Edsal CR3618 User Manual
Heavy Duty
Steel Shelving
B - Braces
D - Woodboard Shelf
MODEL NUMBER
CR3618 - CR4824
A - Beams
C - Post
CR3618 5 Shelf
CR3618 5 Shelf
CR3618 5 Shelf
Description
A - Beams
B - Braces
C - Post
D - Woodboard
Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a
possible safety hazard. This unit should be securely anchored to a wall or floor with suitable fasteners, which are not
included. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY
PART OF THE UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the
heavier loads on the bottom. Use care when working with metal parts.
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used
on the beams and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block
of wood between the hammer head and the parts to prevent damage. Tap gently and be sure the rivets are straight and
fully engaged.
Qty.
10
10
8
5
-
72”h x 18”d x 36”w
-
72”h x 18”d x 36”w
-
72”h x 18”d x 36”w
Part Number
RCBE3503
RCBE1703
RUPT3602S
RPB21836
Part Size
35 9/32”
17 9/32”
36”
35 29/32”
A - Beams
B - Braces
C - Post
D - Woodboard
CR4824 5 Shelf
CR4824 5 Shelf
CR4824 5 Shelf
Description
Qty.
10
10
8
5
-
72”h x 24”d x 48”w
-
72”h x 24”d x 48”w
-
72”h x 24”d x 48”w
Part Number
RCBE4703
RCBE2303
RUPT3602S
RPB22448
Part Size
47 9/32”
24 9/32”
36”
47 29/32”
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel
free to contact our Muscle Rack manufacturing facility at, (773) 475-3000 and request customer service.
We can also be reached on the internet at the following email address : customerservice@edsal.com.
To obtain replacement parts, please provide the following information :
- Model # - Part # & Description - Location Purchased - Date Purchased
Consumer Products Division
Edsal Manufacturing Company
4400 South Packers Avenue
Chicago, IL 60609 www.edsal.com
Assembly Instructions for CR3618 & CR4824
Assembly Instructions for CR3618 & CR4824
Assembly Instructions for CR3618 & CR4824
Step
1
Figure A
Post
Brace
Assemble two (2) post with one (1) brace. Skipping one slot
from the bottom of the post (see figure A), place the rivets
into post with the slot pointing down, and with the shelf ledge
of the brace facing up (see figure B). Tap lightly to seat rivets. Repeat with two (2) post and one (1) brace. Assemble
the two (2) post units with two (2) beams (see figure C). Skip
one hole from the bottom of post, tap lightly to seat rivets.
Figure B
Note:
Post are
directional.
The slot
must point
down.
Figure C
Figure C
Tap Lightly
Shelf Ledge
Post Slot Points Down
Beam
Step
2
Woodboard Shelf
Start by adding a woodboard shelf to the level previously
built, then continue working by adding the second level
using two (2) beams and two (2) braces in the post slots
of your desired location. Again place the rivets of the
beams and braces into the post slots with the shelf
ledge facing up and tap lightly to seat the rivets.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
IMPORTANT NOTE : Make sure all rivets are fully seated into the post slots.
Step
Note:
Post are directional. The slot
must point down.
3
Top
Figure D
Tap Lightly
Bottom
Post
Add a woodboard shelf to the previously built level, then
assemble the top post to the bottom post by using two (2)
beams and two (2) braces. One (1) rivet from each beam
and brace must be placed in the top hole of the bottom
post, and the bottom hole of the top post (see figure D).
After all beams and braces are in place, tap lightly to
properly seat the rivets.
Post
Slot
Down
Woodboard Shelf
Step
4
Add a woodboard shelf to the previously built level, then
continue by adding the fourth and fifth level to the unit
using two (2) beams and two (2) braces per level. Tap
lightly to properly seat the rivets and add the final woodboard shelves to the unit.
Loading...