Edsal 3011 User Manual

(A) Back

Congratulations ! On the purchase of your Edsal Quick Assemble Wardrobe Cabinet.

(B) Right Hand Side (C) Left Hand Side

(some assembly required)

(H) Door Frame

(I) Door Rods

(M) Hanger Rod

MODEL NUMBER (s)

(L) Locking Handle

(K) Leg Leveler & Cage Nut

3011KA - 3012KA

Page 1

(G) Shelf Clips

(J) 10-24 x 3/8” Screws & Nuts

Required Tools

• Small Screwdriver

• Rubber Mallet

(F) Shelves

• Socket or Nut Driver

Safety Instructions

(D) Top (E) Bottom

Use Caution when handling and assembling metal parts. The metal may have sharp edges or corners. The use of protective gloves is recommended. Do not use this unit for anything that is outside the designed function of storage. Do not store loose or heavy items on the top shelves or on the top of the unit, for they create a falling hazard that can injure yourself or others. Always remember to use proper lifting techniques when moving either the boxed or assembled unit.

General instructions

It is recommended that the cabinets are assembled by more than one person. Use of a raised flat surface during assembly is highly recommended. During shipping and handling, some of the panels that are used for assembly may have become bent. Use your hand to pry up or push the parts back to their original form. To assure that the unit is square. Make sure that the unit is placed on a level surface, as this may effect the performance of the unit.

Part List & Product Specification : Edsal 3011KA & 3012KA Series Wardrobe Cabinet (patent pending)

3011KA

Reference

A B C D E F G H

I J K L M

Description

Back

Right Hand Side

Left Hand Side

Top

Bottom

Shelf

Shelf Clips

Door Frame

Door rods 10-24X3/8” Screw & Nut Leg Leveler & Cage Nut

Locking Handle

Hanger Rod

78”h x 18”d x 36”w

3011KA

78”h x 18”d x 36”w

3011KA

Qty.

1 1 1 1 1 1 2 1 2 2 2 1 1

78”h x 18”d x 36”w

CUBK7837 KA CUSD7820R KA CUSD7820L KA

CUTO3820 KA

CUBO3617-1 KA CUSH3718-2 KA

7000CLP

3000FRAME CUDR3500 KA F102438S & N

Leveler 100

201L

CCHG4102

Qty.

1 1 1 1 1 1 2 1 2 2 2 1 1

3012KA

78”h x 24”d x 36”w

3012KA

78”h x 24”d x 36”w

3012KA

78”h x 24”d x 36”w

CUBK7837 KA

CUSD7826R KA

CUSD7826L KA

CUTO3826 KA CUBO3623-1 KA CUSH3724-2 KA

7000CLP

3000FRAME CUDR3500 KA F102438S & N

Leveler 100

201L

CCHG4102

Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact

our Edsal manufacturing facility at, (773) 475-3000 and request customer service. We can also be reached on the internet

at the following email address : customerservice@edsal.com.

To obtain replacement parts, please provide the following information :

- Model # - Part # & Description - Location Purchased - Date Purchased

Consumer Products Division Edsal Manufacturing Company

4400 South Packers Avenue Chicago, IL 60609 www.edsal.com

Made In China

Assembly Instructions : Edsal 3011KA & 3012KA Series Wardrobe Cabinets Page 2

Important Please Read First

This instruction sheet was designed to help you assemble this unit in the proper way, please follow them using all parts and fasteners provided. Any alteration or deviation from this instruction sheet can result in unit failure. If you have any assembly problems or questions, please feel free to contact our Edsal manufacturing facility at (773) 475-3000 during the hours of 9:00 a.m. to 5:00 p.m. central standard time and ask for customer service. We have people available to assist you if need be with any part of this assembly process.

IT IS HIGHLY RECOMMENDED TO ASSEMBLE THIS UNIT AT EYE LEVEL, AND WITH THE HELP OF AN ADDITIONAL PERSON. Using a RAISED surface such as a TABLE or DESK, will greatly EASE the ASSEMBLY PROCESS. Assembly attempted on a much lower surface such as the floor, is still possible but does make the

assembly process longer and harder. During the shipping and handling of this product, some of the panels may have a MINOR bend such as on a corner, door hinge pin, or a tab. This minor variation can be REPAIRED SIM- PLY by using a SMALL TOOL or your HAND to move the material back to its designed form. A example will be outlined in the “GETTING STARTED” section listed below. Some of the materials used in the packaging to protect the parts from damage may leave dust or smudges on the steel panels. It is RECOMMENDED AFTER AS-

SEMBLY IS COMPLETE to use a MILD SOAP and WATER with a SOFT CLOTH to wipe the unit clean.

Getting Started

This assembly process uses tabs, notches, rectangular, and square holes to hold the parts together. To speed the assembly process, have a rubber mallet, and a small blade screwdriver ready. After unpacking all the panels, visually inspect the corners. These are the most susceptible to damage through the shipping and handling process. If you find a corner bent out of place, use your hand and gently move the corner back to the designed shape. Also during shipping and handling some of the tabs used for engaging the panels together may have become closed. Visually inspect all panels and if found that some are closed, use a small blade screwdriver to push the tabs from behind to open slightly (it is recommend to push tabs out slightly for ease of assembly, and then tap back down with a rubber mallet, to tighten engagement). A example of pushing the tabs out and how the engagement process works, is shown below.

Push tab slightly from back side to open

Piece with tab goes under piece with rectangular

Small blade screwdriver

hole

Step 1 - Side Assembly

First step is to identify the right side panel and the left side panel. Identify by taking one of the panels and place the tab edge facing down. Now look at the top and bottom edges. The top of the side has a notches on the flanges, and the bottom has a bend inward (see figure

1). Place the corresponding side panel under the back assembly making sure the tabs of the side panel ride into the rectangular holes of the back assembly. Slide the parts together making sure that the tabs and rectangular holes fully engage (if properly completed, the side and back assembly will be even at both ends. After assuring the correct side is fastened to the back assembly and the tab engagements are complete, tap tabs down with a rubber mallet to tighten the engagement. Repeat the same process for the opposite side panel.

Slide part

Tap tab with rubber mallet to tighten engagement

Tab fully engaged

Figure 1 - Side Assembly

Side top flange notches

Back’s rectangular holes

+ 2 hidden pages

Edsal 3011 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual