Edsal 1UGK8 User Manual
Instruction Manual - Mobile Bin Unit - 1UGK8
72 Bins
66” w
10 Shelf
10 Shelf
10 Shelf
Description Qty. Part # Size
Caster (single post) 4
Caster (double post) 2
Post 8 RUPT6302 63"
Beam - Double Rivet 8 RBBR3202 33"
Brace - Double Rivet 8 RBBR1402 15"
Beam - Single Rivet 32 RBBE3201 33"
Brace - Single Rivet 4 RBBE1401 15"
Post Coupling 4 PC101 3"
Wire Deck - 3 Large Bins 6 WD1533L 33" x 15"
Wire Deck - 4 Medium Bins 6 WD1533M 33" x 15"
Wire Deck - 5 Small Bins 6 WD1533S 33" x 15"
Wire Deck - Flat 2 WD1533 33" x 15"
Large Plastic Bin 18 PB15106 10.6" x 6.1" x 15.4"
Medium Plastic Bin 24 PB15076 7.5" x 6.3" x 15.4"
Small Plastic Bin 30 PB15063 6.0" x 3.3" x 15.4"
Safety Instructions
Safety Instructions
Safety Instructions
These units should be placed on a level surface. Failure to do so can result in poor product performance or create a possible safety
hazard. Do not use this unit for anything other than the manufactures intended purpose. DO NOT STAND ON ANY PART OF THE
UNIT, OR USE IT AS A LADDER. Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
DO NOT OVERLOAD. Use care when working with metal parts.
When moving the unit, always push from the sides. NEVER push from the front, back, or top. This can cause a “tipping” hazard,
which can result in a serious injury to yourself or others. NEVER pull the unit during movement, push the unit to the location.
Always move the unit over a flat level surface. Rough surfaces cause the unit to vibrate, which causes the unit’s load to increase in
weight, or again may cause a “tipping” hazard which can result in a serious injury to yourself or others. Do not store any items on
the top of the unit during movement, this may cause a “falling” hazard that can injure yourself or others.
-
66” w
-
66” w
-
-
72 Bins
-
72 Bins
-
Swivel Single
Swivel Double
3"
3"
General Instructions
General Instructions
General Instructions
Assembly is done with the rivets of the beams and braces fitting into the slots of the post. A rubber mallet may be used on the beams
and braces to seat the rivets properly. A hammer can also be used, providing one uses a cloth or a block of wood between the hammer
head and the parts to prevent damage. Tap gently and be sure the rivets are straight and fully engaged.
Should you have any comments, damage, missing parts, or problems with assembly of this unit please feel free to contact our Edsal manufacturing facility at,
To obtain replacement parts, please provide the following information : Model # - Part # & Description - Location Purchased - Date Purchased
Step 1
Step 1
Step 1
(773) 475-3000 and request customer service. We can also be reached on the internet at the following email address :
customerservice@edsal.com.
Install single insert casters into 4 of the 8 posts.
These will be the outside posts on the
completed unit
Press the plastic caster supports fully into the
welded bracket on the bottom of each of the
4 posts.
Insert caster
Into Post bottom
Make sure caster
is fully inserted
Repeat to assemble
4 single posts
Step 2
Step 2
Step 2
Assemble the 2 Double Posts, which
are used in the center of the unit.
Take 2 Posts and insert the 2-Post
Caster into the bottom brackets.
Install 2 of the Post Couplings in the
specified holes to lock the Posts
together. Make sure the Caster and
Couplings are fully seated.
Repeat to assemble the second
Double Post.
Insert 2Post
Caster into
Posts
Make sure
Caster is fully
inserted
Top Post Coupling
Insert in the
4th and 5th
holes from
top of post
Insert Post
Coupling and
align
Bottom Post Coupling
Insert in the
23rd and
24th holes
from top of
post
Tap down
Step 3
Step 3
Step 3
Assemble the front and back frames.
Using 2 of the 33” Double-Rivet
Beams assemble the rear frame as
shown. Use the Double Posts on
the right side, with the connected
side facing the inside of the unit. Insert the rivets on the Beams into the
slots on the Posts and gently tap
down until they are fully seated.
Repeat the process to build a
matching front frame.
Insert rivets
and tap down
Repeat to assemble
2nd Double Post
33” long,
2 Rivet Beam
Double Post
on right with
flanges
inward
33” long,
2 Rivet Beam
Use the 33” long,
2 Rivet Beams
Assemble the
rear frame
Repeat to assemble
the front frame
Loading...