EDS SD630A, SD630A24, SD630AK, SD630AK24 Installation Manual

SD630A AK, SD630A24 AK24//

INSTALLATION MANUAL

TELEPHONE DIALLER

4 12

TELEPHONE DIALLER

SD630A AK, SD630A24 AK24//

KK-SD630/110907_ER3
f:/pazarlama/kullanýmkýlavuzlarý/eds/english/sd630_ER3

How to Delete a Pre-entered Telephone Number

Engineering code

MMMM#01#

MMMM#02#
MMMM#03#.
MMMM#04#
MMMM#05#
MMMM#06#

MMMM:

For deleting 1. Telephone number:
For deleting 2. Telephone number:
For deleting 3. Telephone number:
For deleting 4. Telephone number:
For deleting 5. Telephone number:
For deleting 6. Telephone number:

(default 1234 )

After entering the 4-digit engineering code, #, row number and user code
if you enter a valid syntax you hear, two beeps. If you enter an invalid syntax you hear single beep. That means wrong
operation has been done, and the commands are ignored. You could repeat the operation by pressing # button.

1234#01#

please enter the followings in order:

Example:

When thedevice receives analarm it starts callingthe pre-entered telephonenumbers from the firstnumber. It cancall
5 times if the dialed number doesn't answer or it is busy. After 10 times ringing if it's not answered it calls the next
number. Thedevice reads16 seconds recordedvoice.

After reading the message, the device waits 10 seconds to have an order. After listening the message enter the user
code than press the 2 button and if you heard two beeps it cannot call the following telephone number, the relay is
became anactive conditionsby entering usercode thanpressing 1 buttonin 10seconds.

To makeanother operation2-3 seconds shouldbe wait.(The relay inactive conditions.)

The devicereads 16seconds recorded voice:

NOTE:

How the device operates

How to Enter Passwords

After entering the 4-digit engineering code, #, row number and user code
if you enter a valid syntax you hear, two beeps. If you enter an invalid syntax you hear single beep which means
wrong operation. You can repeat the operation by pressing # button.

please enter the followings in order:

MMMM:
SxSxSx:
Example:

Engineering code (default 1234 )

New password

1234 # 07 5612 if you want to set 5612 user password

Setting 1. Telephone's number's password: MMMM # 07 S1S1S1
Setting 2. Telephone's number's password. MMMM # 08 S2S2S2
Setting 3. Telephone's number's password: MMMM # 09 S3S3S3
Setting 4. Telephone's number's password: MMMM # 10 S4S4S4
Setting 5. Telephone's number's password: MMMM # 11 S5S5S5
Setting 6. Telephone's number's password: MMMM # 12 S6S6S6

Changing the engineering code: MMMM #13 S7S7

General Specifications

Technical Specifications

TELEPHONE DIALLER

•

•

•

•

•

•

•

If the dialed numbers do not answer, can call 5times
16 seconds voice message recording time
Recorded messages and telephone numbers are not erased in caseof power failure
Special password for each number
Receives the lines and calls incase of alert even ifthe line is busy
Relay can be controlled by special password
Microprocessor controlled

2 4 3

4

SD 630A is a security dialer which calls up to six telephone numbers and playbacks pre-recorded voice as a warning
message, when an alarm occurs. The alarm is detected when the alarm terminal of the device are open-circuited. In
normal operation alarm terminals should be short-circuited and jumpers should be positioned as shownin figure 3
and jumpers must be positioned as shown in Figure 3 and a phone line is connected to LINE terminal of the device.

J1 and J2 should be in N (Normal) position while in normal working mode, as shown in Figure 3. Operates with
Negative Triggering When the Jumper 5 as in Figure 1, and operates with Positive Triggering when the jumper as in
Figure 2.

Max Voice Recording Time
Calling Time
Power Supply
Power Consumption
Box Type
Box Dimension

Model

SD630A SD630AK

TELEPHONE DIALLER

16 sn.
70sec (Tone)-80sn. (Pulse)
12VDC 24V DC
Max.50mA(sleep mode) max.100mA(active mode)
ABS plastic Card type ABS plastic
12x15.7x3.2 90x80x25 12x15.7x3.2

General Issues

Parameters and Programming Methods

NOTE 1:
NOTE 2:
NOTE 3:
NOTE 4:
NOTE 5:

NOTE 6:

We can start to operate SD 630A 3 seconds after supplying power.

Siren sound is heard on the telephone on alarm conditions.
The alarm output of the alarm panel should be dry contact type.
Fabrication engineering code is 1234.
To return to the fabrication codes, please, first cut off the power, short circuit J4 then apply the power. You

will hear the confirmation sound then you should make J4 open-circuit.

Operating frequency is between 390Hz and 490Hz

SD630A24 SD630AK24

POZ

NEG

POZ

NEG

J5

Figure 1

PN

J2

Figure 3Figure 2

PN

J1

J1J2

J3

J5

J4

(Jumper Positions for programming Mode)

How to Program the Device

The device should be programmed before using it. During programming J1 and J2 jumpers conditions should be

as in figure 4. 6 telephone numbers can be programmed and each telephone number can have special password

Voice Recording and Playback

To Record Voice :

To Playback:

J1 and J2 must be programming conditions . Hang up the telephone which is connected to
the TEL port of the device and short-circuit J3 jumper when the red led on the PCB is on device start recording your
warning message. The messageshould notexceed 16 seconds. When theLED light is offthat means the recordingtime
is over.When therecording is finishedJ3 jumpermust be open-circuitedagain.

J1 and J2must be programming conditions(Figure 4). By pressing MMMM# 14 buttons. Youcould listen
the pre-recordedmessage. To passdifferent operation youmust wait 16 seconds.The device cannot make telephone call
if thewarning messagewasn't recorded.

(Figure 4 )

Tone, Pulse Selection

At default, the dialer is in tone mode; by pressing it would be converted to the pulse mode.MMMM #15

SD630A AK, SD630A24 AK24// SD630A AK, SD630A24 AK24//

MMMM:
Example:

Engineering code (default 1234 )

1234 # 01 0532 9876543# (If you want to enter 0532 9876543)

TEL

(Programmer)

LINE

(Telephone

Line)

ALRM

(Trigger)

COM NC

(

Relay Output)

NO

+12V-

(Power supply)

PCB CARD

'

(to program the
device you need)

Important:

telephone line must be direct,
please don’t connect PABX devices.

N.C
Trigger Button
(to make the device call)

12V

Power Supply

. Telephone number: MMMM #04 Tel4 #

Telephone number: MMMM #05 Tel5 #

Telephone number: MMMM #06 Tel6 #

Setting 4
Setting 5.
Setting 6.

Setting 1.
Setting 2.
Setting 3.

Telephone number: MMMM #01 Tel1 #

Telephone number: MMMM #02 Tel2 #
Telephone number: MMMM #03 Tel3 #

J2 J1

PPN

N

Figure 4

PPN

N

NOTE: After entering, 4-digit engineering code, #, row number, telephone
number and #, if you enter a valid syntax you hear, two beeps. If you anter an invalid syntax you hear single beep
which means wrong operation. You can repeat the operation by pressing # button.

please enter the followings in order: