Edirol V-8 User Manual
Owner’s Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 6–7; p. 8). These sections provide
important information concerning the proper operation of the unit. Additionally,
in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s Manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
Copyright © 2008 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without
the written permission of ROLAND CORPORATION.
Confirm the Contents of the Package
The V-8 includes the following items. Please take a moment to confirm that all of these items have been included with the V-8. If you
find that any item is missing, contact the nearest authorized EDIROL/Roland distributor in your country.
V-8
AC adaptor/Power cord
* The shape of the power cord’s plug varies depending
on the country.
RCA-BNC adaptor plugs (four)
Screws for attaching the video fader
(four spare screws)
Owner’s manual (this document)
For the U.K.
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
BLUE:
BROWN:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.
NEUTRAL
LIVE
2
Main Features
●
Eight channels of video input
The V-8 provides video input connectors for eight video (composite) channels and four S-video channels. Of the
input channels 1–8, S-video input is available only for channels 5–8.
* If S-video and video (composite) are both input to a channel 5–7, the input from the S-video connector will take priority and
will be selected automatically. Likewise, if S-video and RGB signals from a computer are both input to channel 8, the S-video
will take priority.
●
Computer input jacks with built-in scan converters
A built-in scan converter supports RGB signals (VGA to UXGA) from a computer. The incoming RGB signal is
converted to a video signal. By key-compositing a computer screen with a video image, you can use this as a titler.
* There are two computer input connectors. A switch on the operating panel allows one of the two to be selected.
●
Two independent frame synchronizers
Even if an unstable video signal is input, the internal frame synchronizer can correct the synchronization signal.
This allows you to use a variety of video without worrying about noise caused by unstable synchronization signals.
●
Monitor out connectors for eight channels
An independent monitor out connector is provided for each video input channel 1–8.
* If both S-video and video (composite) signals are being input to channels 5–7, or if both an S-video signal and a computer
output signal are being input to channel 8, the input from the S-video connector will take priority, and will be sent from monitor
out. The input signal from the computer will also be sent from monitor out as a video signal.
●
High-quality digital effects
Digitally processed effects are built in. You can apply a variety of high-quality effects including Picture In Picture,
Mirror, Multi, Feedback, and Afterimage. In addition to the familiar Mix and Wipe transitions, new transitions such
as FAM (Full Additive Mix), NAM (Non-Additive Mix), Slide, and Stretch are also provided.
●
Simple and customizable operation
Switching between video sources and mixing them is easy. The T-bar type video fader can be attached in either
a horizontal or vertical orientation according to your preference. Sliders are used for effect controllers, allowing
you to operate the V-8 like a DJ mixer.
●
Synchronize with music
By pressing the TAP button in time with the beat of the music, you can switch images or control effects in
synchronization with the tempo (BPM).
●
Control via MIDI
MIDI connectors (IN, OUT/THRU) are provided, allowing you to switch images or control effects by controlling the
V-8 from an external MIDI device. You can also control an external device from the V-8.
In addition, the V-8 can be used in conjunction with V-LINK compatible audio/video equipment to easily create
video output that is linked with the expressive elements of a performance.
3
Table of Contents
Introduction
Confirm the Contents of the Package ......................................................................................................................................2
Main Features .............................................................................................................................................................................3
USING THE UNIT SAFELY .........................................................................................................................................................6
IMPORTANT NOTES ..................................................................................................................................................................8
Video Signal Flow ......................................................................................................................................................................9
Panel Descriptions................................................................................................................................................................... 10
Connecting Peripheral Devices 14
Basic Connections................................................................................................................................................................... 14
Connecting the AC Adaptor .................................................................................................................................................15
Examples of Using the V-8 ......................................................................................................................................................16
Basic Operation 20
Turning the Power On/Off .......................................................................................................................................................20
Checking the Input and Output............................................................................................................................................... 21
Outputting Images ...............................................................................................................................................................21
Outputting a Preview Image ................................................................................................................................................22
Menu Operations...................................................................................................................................................................... 23
Preparations for Viewing the Menu...................................................................................................................................... 23
Operating the Menu .............................................................................................................................................................24
About the Current Settings Display .......................................................................................................................................26
Changing the Contents of the Settings Display ...................................................................................................................27
Storing the Operating Panel Settings ([MEMORY] Knob) ....................................................................................................28
Settings Stored at the [MEMORY] Knob.............................................................................................................................. 28
Recalling a Memory .............................................................................................................................................................29
Copying the Contents of a Memory .....................................................................................................................................29
Exchanging the Contents of Memories................................................................................................................................30
Fading Out the Output Image.................................................................................................................................................. 31
Fading Out the Bus A / Bus B Image...................................................................................................................................31
Fading Out the Final Output ................................................................................................................................................32
Returning the Menu Settings to the Factory-Set State (Factory Reset).............................................................................. 33
Returning All Settings to the Factory-Set State ...................................................................................................................33
Returning the Settings of a Specific Sub-Menu to the Factory-Set State ............................................................................34
Switching Between Images 35
Switching Between Two Images............................................................................................................................................. 35
Changing the Transition Assigned to Each TRANSITION Button .......................................................................................36
Combining Multiple Transition Effects (User Transition)...................................................................................................... 38
Using the [TRANSFORMER] Buttons to Switch Images ......................................................................................................40
Changing the Assignment of the [TRANSFORMER] Buttons.............................................................................................. 41
Using Effects 42
About Effects............................................................................................................................................................................ 42
Combining Two Images........................................................................................................................................................... 43
Using Picture In Picture (P in P) to Combine Images ..........................................................................................................43
Using Chroma-Key to Combine Images ..............................................................................................................................45
Using Luminance-Key to Combine Images .........................................................................................................................46
Changing the Color of the Image............................................................................................................................................ 48
Inverting the Image to Form a Negative ..............................................................................................................................48
Adding Color According to the Brightness or Darkness of the Image (Colorize) .................................................................49
Repeatedly Layering an Image onto Itself (Feedback) ......................................................................................................... 50
Using Multi-Screen................................................................................................................................................................... 51
Inverting the Image (Flip) ........................................................................................................................................................52
Assigning Different Effects to the EFFECTS Buttons ..........................................................................................................53
4
Table of Contents
(continued)
Editing the Input/Output Settings 54
Adjusting the Input Image .......................................................................................................................................................54
Adjusting the PC Input Image ..............................................................................................................................................54
Adjusting the Input Image for Bus A and B..........................................................................................................................56
Adjusting the Output Image ....................................................................................................................................................57
Outputting Color Bars .............................................................................................................................................................58
Switching Between NTSC and PAL ........................................................................................................................................59
Switching Images in Synchronization with Music (BPM Sync) 60
Switching Images at a Specified BPM.................................................................................................................................... 60
Switching Images at the Tempo Specified by the [TAP] Button.......................................................................................... 61
Changing the Settings of the [BPM SYNC] Button ...............................................................................................................62
Using the V-8 with Other Equipment 63
Using MIDI to Control the V-8 from an External Device .......................................................................................................63
About MIDI...........................................................................................................................................................................63
Buttons and Knobs that Transmit or Receive MIDI Messages ............................................................................................64
MIDI Message Transmission Settings .................................................................................................................................66
MIDI Message Reception Settings ......................................................................................................................................68
Saving V-8 Settings on an External MIDI Device (Bulk Dump) ............................................................................................69
Transmitting Menu Setting Data to an External MIDI Device ..............................................................................................69
Restoring Data Saved on an External MIDI Device Back into the V-8 ................................................................................70
Sending the V-8’s Settings to Another V-8 ..........................................................................................................................71
Controlling via V-LINK .............................................................................................................................................................72
What is V-LINK? ..................................................................................................................................................................72
Controlling the RSS M-400 from the V-8 (V-LINK Master) ..................................................................................................72
Controlling the V-8 from an External V-LINK Compatible Device (V-LINK Slave)...............................................................74
Using the V-8 in Conjunction with the PR Series (PR Control mode).................................................................................75
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Adjusting the Video Fader 76
Installing the Video Fader in the Most Convenient Orientation........................................................................................... 76
Calibrating the Video Fader ....................................................................................................................................................77
Specifying the Video Fader Operating Curve........................................................................................................................ 78
Appendices 79
Troubleshooting....................................................................................................................................................................... 79
Menu List ..................................................................................................................................................................................81
MIDI Implementation ................................................................................................................................................................90
MIDI Implementation Chart...................................................................................................................................................... 98
Transition Effect List ...............................................................................................................................................................99
Effect List................................................................................................................................................................................ 105
Effects that Can Be Controlled by the [CONTROL] Fader................................................................................................. 106
Effects that Cannot Be Used Simultaneously ....................................................................................................................107
Block Diagram ........................................................................................................................................................................108
Main Specifications................................................................................................................................................................ 109
Index........................................................................................................................................................................................ 110
Information .............................................................................................................................................................................113
Input/output
settings
5
USING THE UNIT SAFELY
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
002d
●
Do not open or perform any internal modifications on the
unit or its AC adaptor. (The only exception would be
where this manual provides specific instructions; see
p. 76.)
..........................................................................................................
003
●
Do not attempt to repair the unit, or replace parts within
it (except when this manual provides specific
instructions directing you to do so). Refer all servicing to
your retailer, the nearest EDIROL/Roland Service
Center, or an authorized EDIROL/Roland distributor, as
listed on the “Information” page.
..........................................................................................................
004
●
Never use or store the unit in places that are:
•
Subject to temperature extremes (e.g., direct sunlight
in an enclosed vehicle, near a heating duct, on top of
heat-generating equipment); or are
•
Damp (e.g., baths, washrooms, on wet floors); or are
•
Humid; or are
•
Exposed to rain; or are
•
Dusty; or are
•
Subject to high levels of vibration.
..........................................................................................................
007
●
Make sure you always have the unit placed so it is level
and sure to remain stable. Never place it on stands that
could wobble, or on inclined surfaces.
..........................................................................................................
008c
●
Be sure to use only the AC adaptor supplied with the
unit. Also, make sure the line voltage at the installation
matches the input voltage specified on the AC adaptor’s
body. Other AC adaptors may use a different polarity, or
be designed for a different voltage, so their use could
result in damage, malfunction, or electric shock.
..........................................................................................................
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the triangle.
In the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
008e
●
Use only the attached power-supply cord. Also, the
supplied power cord must not be used with any other
device.
..........................................................................................................
009
●
Do not excessively twist or bend the power cord, nor
place heavy objects on it. Doing so can damage the
cord, producing severed elements and short circuits.
Damaged cords are fire and shock hazards!
..........................................................................................................
011
●
Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
..........................................................................................................
012b
●
Immediately turn the power off, remove the AC adaptor
from the outlet, and request servicing by your retailer,
the nearest EDIROL/Roland Service Center, or an
authorized EDIROL/Roland distributor, as listed on the
“Information” page when:
•
The AC adaptor, the power-supply cord, or the plug
has been damaged; or
•
If smoke or unusual odor occurs
•
Objects have fallen into, or liquid has been spilled
onto the unit; or
•
The unit has been exposed to rain (or otherwise has
become wet); or
•
The unit does not appear to operate normally or
exhibits a marked change in performance.
..........................................................................................................
013
●
In households with small children, an adult should
provide supervision until the child is capable of following
all the rules essential for the safe operation of the unit.
..........................................................................................................
6
USING THE UNIT SAFELY
(continued)
014
●
Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
●
Do not force the unit’s power-supply cord to share an
outlet with an unreasonable number of other devices. Be
especially careful when using extension cords—the total
power used by all devices you have connected to the
extension cord’s outlet must never exceed the power
rating (watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat up
and eventually melt through.
..........................................................................................................
016
●
Before using the unit in a foreign country, consult with
your retailer, the nearest EDIROL/Roland Service
Center, or an authorized EDIROL/Roland distributor, as
listed on the “Information” page.
..........................................................................................................
022b
●
Always turn the unit off and unplug the AC adaptor
before attempting installation of the video fader (p. 76).
..........................................................................................................
101b
●
The unit and the AC adaptor should be located so their
location or position does not interfere with their proper
ventilation.
..........................................................................................................
102c
●
Always grasp only the plug on the AC adaptor cord
when plugging into, or unplugging from, an outlet or this
unit.
..........................................................................................................
103b
●
At regular intervals, you should unplug the AC adaptor
and clean it by using a dry cloth to wipe all dust and
other accumulations away from its prongs. Also,
disconnect the power plug from the power outlet
whenever the unit is to remain unused for an extended
period of time. Any accumulation of dust between the
power plug and the power outlet can result in poor
insulation and lead to fire.
..........................................................................................................
104
●
Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be placed
so they are out of the reach of children.
..........................................................................................................
106
●
Never climb on top of, nor place heavy objects on the
unit.
..........................................................................................................
107c
●
Never handle the AC adaptor or its plugs with wet hands
when plugging into, or unplugging from, an outlet or this
unit.
..........................................................................................................
108b
●
Before moving the unit, disconnect the AC adaptor and
all cords coming from external devices.
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
..........................................................................................................
109b
●
Before cleaning the unit, turn off the power and unplug
the AC adaptor from the outlet.
..........................................................................................................
110b
●
Whenever you suspect the possibility of lightning in your
area, disconnect the AC adaptor from the outlet.
..........................................................................................................
115a
●
For installation of the video fader, remove only the
specified screws (p. 76).
..........................................................................................................
118c
●
Keep any screws for the attaching the video fader and
ground terminal you may remove and the included RCABNC adaptor plugs and screws for attaching the video
fader in a safe place out of children’s reach, so there is no
chance of them being swallowed accidentally.
..........................................................................................................
Input/output
settings
7
IMPORTANT NOTES
Power Supply
301
●
Do not connect this unit to same electrical outlet that is being
used by an electrical appliance that is controlled by an inverter
(such as a refrigerator, washing machine, microwave oven, or air
conditioner), or that contains a motor. Depending on the way in
which the electrical appliance is used, power supply noise may
cause this unit to malfunction or may produce visible noise. If it is
not practical to use a separate electrical outlet, connect a power
supply noise filter between this unit and the electrical outlet.
302
●
The AC adaptor will begin to generate heat after long hours of
consecutive use. This is normal, and is not a cause for concern.
307
●
Before connecting this unit to other devices, turn off the power to
all units. This will help prevent malfunctions and/or damage to
video monitors or other devices.
Placement
352a
●
This unit may interfere with radio and television reception. Do not
use this unit in the vicinity of such receivers.
352b
●
Noise may be produced if wireless communications devices, such
as cell phones, are operated in the vicinity of this unit. Such noise
could occur when receiving or initiating a call, or while
conversing. Should you experience such problems, you should
relocate such wireless devices so they are at a greater distance
from this unit, or switch them off.
355b
●
When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation)
may form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using
the unit, you must allow it to stand for several hours, until the
condensation has completely evaporated.
360
●
Depending on the material and temperature of the surface on
which you place the unit, its rubber feet may discolor or mar the
surface.
You can place a piece of felt or cloth under the rubber feet to
prevent this from happening. If you do so, please make sure that
the unit will not slip or move accidentally.
Maintenance
401a
●
For everyday cleaning wipe the unit with a soft, dry cloth or one
that has been slightly dampened with water. To remove stubborn
dirt, use a cloth impregnated with a mild, non-abrasive detergent.
Afterwards, be sure to wipe the unit thoroughly with a soft, dry
cloth.
402
●
Never use benzine, thinners, alcohol or solvents of any kind, to
avoid the possibility of discoloration and/or deformation.
Additional Precautions
***
●
This unit allows you to switch images or turn video effects on/off
at high speed. For some people, viewing such images can cause
headache, nausea, or other discomfort. Do not use this unit to
create video that might cause these types of health problems.
Roland Corporation will accept no responsibility for any such
health problems that may occur in yourself or in viewers.
551
●
Please be aware that the contents stored at the [MEMORY] knob
(p. 28) can be irretrievably lost as a result of a malfunction, or the
improper operation of the unit. To protect yourself against the risk
of loosing important data, we recommend that you periodically
save a backup copy of important data you have stored in the
unit’s memory in another MIDI device (e.g., a sequencer).
552
●
Unfortunately, it may be impossible to restore the contents of data
that was stored in another MIDI device (e.g., a sequencer) once it
has been lost. Roland Corporation assumes no liability
concerning such loss of data.
553
●
Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and
connectors. Rough handling can lead to malfunctions.
556
●
When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing
shorts, or damage to the cable’s internal elements.
559c
●
When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise, you will
need to use equivalent packaging materials.
Copyright
851
●
Recording, duplication, distribution, sale, lease, performance, or
broadcast of copyrighted material (musical works, visual works,
broadcasts, live performances, etc.) belonging to a third party in
part or in whole without the permission of the copyright owner is
forbidden by law.
852a
●
This product can be used to record or duplicate visual material
without being limited by certain technological copy-protection
measures. This is due to the fact that this product is intended to
be used for the purpose of producing original video material, and
is therefore designed so that material that does not infringe
copyrights belonging to others (for example, your own original
works) can be recorded or duplicated freely.
853
●
Do not use this unit for purposes that could infringe on a copyright
held by a third party. We assume no responsibility whatsoever
with regard to any infringements of third-party copyrights arising
through your use of this unit.
Repairs and Data
452
●
Please be aware that all data contained in the unit’s memory may
be lost when the unit is sent for repairs. Important data should
always be backed up in another MIDI device (e.g., a sequencer),
or written down on paper (when possible). During repairs, due
care is taken to avoid the loss of data. However, in certain cases
(such as when circuitry related to memory itself is out of order),
we regret that it may not be possible to restore the data, and
Roland assumes no liability concerning such loss of data.
8
* Microsoft and Windows are registered trademarks of Microsoft
Corporation.
207
* Apple and Macintosh are registered trademarks of Apple Inc.
* MMP (Moore Microprocessor Portfolio) refers to a patent
portfolio concerned with microprocessor architecture, which
was developed by Technology Properties Limited (TPL).
Roland has licensed this technology from the TPL Group.
Video Signal Flow
fig.signal-flow-e.eps
You can use the input selector to choose any two of the video signals coming into the eight input jacks. These two video
signals are sent to
The video signals sent to bus A and bus B are mixed in the video mixer section. The mixed signal then passes through the
output fader and is sent from the output jack.
☞
For details on the structure of the mixer, refer to “Block Diagram” (p. 108).
INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6 INPUT7 INPUT8 PC1 PC2
bus A
and
bus B
of the video mixer section.
Video device Computer
PC input selector
Scan converter
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Input s
elector
Bus A
Effects
Fader
Video mixer
Output fader
Bus B
Effects
Fader
Preview selector
Inside of the V-8
OUTPUT
Final output
* The preview output will also show the settings menu of the V-8 overlaid with the image (p. 23).
* INPUTs 5–7 provide composite connectors and S-video connectors. If an image is being input to both connectors of the
same channel, the input from the S-video connector will take priority.
* INPUT 8 provides both an S-video connector and a PC connector. If an image is being input to both of these, the input
from the S-video connector will take priority.
PREVIEW OUT
Preview output
Input/output
settings
9
Panel Descriptions
Operating Panel
fig.top-panel1-e.eps
Menu Operation Buttons
These are used when working with the menu.
☞
“Operating the Menu” (p. 24)
●
[MENU] Button
This button overlays the menu onto the television monitor
connected to the PREVIEW OUT connector (p. 13).
If you’ve moved to a lower-level menu, this button will return you
to the preceding menu (the next higher level).
If the menu is displayed, the [MENU] button will light.
●
[ ] [ ] Buttons
These buttons move the cursor that is displayed in the menu.
Alternatively, they edit a value in the menu.
●
[ENTER] Button
This button confirms the menu item you’ve selected, and takes
you to the next menu (a lower level).
BPM Display
●
This shows the current BPM (Beats Per Minute).
☞
“Switching Images at a Specified BPM” (p. 60)
●
If you’ve chosen “003: Fam✽” or “005: Nam✽” as the transition
effect selected by a TRANSITION button, this will blink to
indicate the FAM/NAM cross point level.
☞
“Changing the cross point of the FAM/NAM” (p. 37)
[BPM/CONTROL] Knob
●
Use this to edit the BPM value.
●
If you’ve used the TRANSITION buttons ( ) to select “003:
Fam✽” or “005: Nam✽” as the transition effect, this will adjust
the way in which the transition occurs.
☞
“About the FAM and NAM Transition Effects” (p. 37)
[MEMORY] Knob
This knob stores up to seven settings (memory numbers 2–8) for
the operating panel (i.e., the buttons and faders). The factory
preset settings are assigned to memory number 1.
The stored settings will be called up when you turn the
[MEMORY] knob to the desired memory number.
☞
“Storing the Operating Panel Settings ([MEMORY] Knob)” (p. 28)
Bus A INPUT SELECT Buttons
Use these buttons to select the image that will be input to bus A
of the video mixer.
fig.inputsel-indicator-e.eps
The indicator of the selected INPUT SELECT
button will light.
☞
“Switching Between Two Images” (p. 35)
* For channels 5–8, input from the S-video connector will take priority.
* Use the [PC INPUT SELECT] button to choose the input from the PC1/
PC2 connectors.
Indicator
[TAP] Button
You can specify the BPM by pressing the [TAP] button at the
desired interval.
☞
“Switching Images at the Tempo Specified by the [TAP] Button” (p. 61)
10
Panel Descriptions
(continued)
Bus A EFFECTS Buttons
These buttons turn effects on/off for the bus A image of the video
mixer. If an effect is on, the button will be lit or blinking.
You can use up to four effects simultaneously.
☞
“Using Effects” (p. 42)
* The EFFECTS button will blink if you’ve selected an effect that can be
controlled by the [CONTROL] fader ( ).
For details, refer to “Effects that can be controlled by the [CONTROL]
faders” (p. 42).
* Depending on the type of effect, there are some combinations that
cannot be used simultaneously. For details, refer to “Effects that Cannot
Be Used Simultaneously” (p. 107).
The settings listed below are the settings for memory number 1
of the [MEMORY] knob. By selecting memory numbers 2–8 you
can assign other effects to the EFFECTS buttons.
[1 (FEEDBACK)] button
[2 (NEGATIVE)] button
[3 (COLORIZE)] button
[4 (MULTI)] button
☞
“Assigning Different Effects to the EFFECTS Buttons” (p. 53)
Feedback (022: FEEDBACK✽)
Negative (033: NEGATIVE✽)
Colorize (042: COLORIZE✽)
Multi (126: MULTI-HV✽)
Bus A [CONTROL] Fader
●
You can use this fader to control the settings of an effect
assigned to the blinking EFFECTS button.
☞
“Effects that can be controlled by the [CONTROL] faders” (p. 42)
●
If the [FADE] button ( ) is blinking, this will fade in/out the
bus A image.
The fade color is fixed at black.
☞
“Fading Out the Bus A / Bus B Image” (p. 31)
Bus A [FADE] Button
This button lets you use the bus A [CONTROL] fader to fade the
bus A image.
While the [FADE] button is blinking, operating the [CONTROL]
fader will fade in/out the bus A image.
[FADE] button Fade function
Blinking
Lit
Unlit
☞
“Fading Out the Bus A / Bus B Image” (p. 31)
On
On
Off
Bus A [TRANSFORMER] Button
This button switches between the bus A and bus B images
without using the video fader.
☞
“Using the [TRANSFORMER] Buttons to Switch Images” (p. 40)
Video Fader
This is a T-bar type video fader. It switches between the bus A
and bus B images.
☞
“Switching Between Two Images” (p. 35)
The video fader can be installed in the V-8 in either a vertical or
a horizontal orientation, and you are free to change this to suit
your preference.
☞
“Installing the Video Fader in the Most Convenient Orientation” (p. 76)
TRANSITION Buttons
Here you can select the way in which you will transition between
the bus A and bus B images. The button you’ve selected will light.
The settings listed below are for memory number 1 of the
[MEMORY] knob. By selecting memory numbers 2–8 you can
assign different transition effects to each TRANSITION button.
[1 MIX] button
[2 WIPE] button
[3 EFX] button
☞
“Switching Between Two Images” (p. 35)
Dissolve (001: Mix01)
Wipe (008: Wipe03)
Soft edge wipe (192: SWipe88)
[BPM SYNC] Button
This lets you automatically switch between images or turn effects
on/off in synchronization with the BPM (BMP Sync).
☞
“Switching Images in Synchronization with Music (BPM Sync)” (p. 60)
PREVIEW OUT SELECT Buttons
These buttons select the preview image that will be output from
the PREVIEW OUT connector (p. 13).
●
[1]–[PC/8] Buttons
The image being input to the INPUT 1–8/PC1/PC2 connector will
be sent from the preview output. The channel number or menu
(p. 23) will be shown overlaid on the preview output.
* The input from the S-video connector will take priority for channels 5–8.
* Use the [PC INPUT SELECT] switch to choose between the PC1/PC2
connector inputs.
* The menu will appear if you press the [MENU] button.
●
[OUTPUT] Button
The final output image will be sent from the preview output.
Information about the settings (p. 26) or the menu (p. 23) will be
shown overlaid on the preview output.
* The menu will appear if you press the [MENU] button.
[PC INPUT SELECT] Switch
This switches between the PC1 input and PC2 input.
[WHITE/BLACK] Switch
This selects either “white” or “black” as the fade color applied
when you operate the [OUTPUT FADE] fader.
WHITE
BLACK
Fade to white
Fade to black
[OUTPUT FADE] Fader
Lowering the [OUTPUT FADE] fader will fade out the image (final
output) being sent from the OUTPUT connector.
Raising the [OUTPUT FADE] fader will fade in the image.
☞
“Fading Out the Final Output” (p. 32)
●
OUTPUT FADE indicator
The indicator located above the [OUTPUT FADE] fader indicates
the fade status.
Blinking
Lit
Now fading in/out
Normal output
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Input/output
settings
11
Panel Descriptions
(continued)
Operating Panel (continued)
fig.top-panel2-e.eps
Bus B INPUT SELECT Buttons
Use these buttons to select the image that will be input to bus B
of the video mixer.
fig.inputsel-indicator-e.eps
The indicator of the selected INPUT SELECT
button will light.
☞
“Switching Between Two Images” (p. 35)
* For channels 5–8, input from the S-video connector will take priority.
* Use the [PC INPUT SELECT] button to choose the input from the PC1/
PC2 connectors.
Bus B EFFECTS Buttons
These buttons turn effects on/off for the bus B image of the video
mixer. If an effect is on, the button will be lit or blinking.
You can use up to four effects simultaneously.
☞
“Using Effects” (p. 42)
* The EFFECTS button will blink if you’ve selected an effect that can be
controlled by the [CONTROL] fader ( ).
For details, refer to “Effects that can be controlled by the [CONTROL]
faders” (p. 42).
* Depending on the type of effect, there are some combinations that
cannot be used simultaneously. For details, refer to “Effects that Cannot
Be Used Simultaneously” (p. 107).
The settings listed below are the settings for memory number 1
of the [MEMORY] knob. By selecting memory numbers 2–8 you
can assign other effects to the EFFECTS buttons.
[1 (FLIP)] button
[2 (CHROMA KEY)] button
[3 (LUMINANCE KEY)] button
[4 (P in P)] button
☞
“Assigning Different Effects to the EFFECTS Buttons” (p. 53)
Flip (102: FLIP✽)
Chroma key (098: CHROMAKEY✽)
Luminance key (096:B-LUMIKEY✽)
Picture in picture (150: PinP✽)
Indicator
Bus B [CONTROL] Fader
●
You can use this fader to control the settings of an effect
assigned to the blinking EFFECTS button.
☞
“Effects that can be controlled by the [CONTROL] faders” (p. 42)
●
If the [FADE] button ( ) is blinking, this will fade in/out the
bus B image.
The fade color is fixed at black.
☞
“Fading Out the Bus A / Bus B Image” (p. 31)
Bus B [FADE] Button
This button lets you use the bus B [CONTROL] fader to fade the
bus B image.
While the [FADE] button is blinking, operating the [CONTROL]
fader will fade in/out the bus B image.
[FADE] button Fade function
Blinking
Lit
Unlit
☞
“Fading Out the Bus A / Bus B Image” (p. 31)
On
On
Off
Bus B [TRANSFORMER] Button
This button switches between the bus A and bus B images
without using the video fader.
☞
“Using the [TRANSFORMER] Buttons to Switch Images” (p. 40)
12
Rear Panel
fig.rear-panel-e.eps
Panel Descriptions
(continued)
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
OUTPUT Connectors
●
Composite output connectors
These are BNC connectors that output the final output image as
a composite video signal.
* If the connection cable you’re using has an RCA phono type plug, use
the included (or commercially available) RCA-BNC adaptors.
●
S-video output connector
This outputs the final output image as an S-video signal.
INPUT Connectors (channels 1–8)
* For channels 5–8, input from the S-video connector will take priority.
●
Composite input connectors (channels 1–7)
These are BNC connectors that input a composite video signal.
Here you can connect video equipment that has composite video
output connectors.
* If the connection cable you’re using has an RCA phono type plug, use
the included (or commercially available) RCA-BNC adaptors.
●
S-video input connectors (channels 5–8)
These connectors can accept S-video signals.
Here you can connect video equipment that has an S-video
output connector.
●
PC1/PC2 input connectors (channel 8)
These are D-sub 15-pin connectors for inputting RGB signals.
Use the [PC INPUT SELECT] switch (p. 11) to choose between
the PC1 input or PC2 input.
☞
“Adjusting the PC Input Image” (p. 54)
MONITOR OUT Connectors (channels 1–7)
These are BNC connectors that output the composite video
signal from the images being input to the composite input
connectors or S-video input connectors.
You can connect these to television monitors that have
composite video inputs, and use them to view the input image for
each channel.
* The input from the S-video connector will take priority for channels 5–7.
* If the connection cable you’re using has an RCA phono type plug, use
the included (or commercially available) RCA-BNC adaptors.
PREVIEW OUT Connector
This is a BNC connector that outputs the composite signal for the
image selected by the PREVIEW OUT SELECT buttons (p. 11).
If you are previewing an input image from the INPUT 1–8/PC1/
PC2 connectors, the channel number or menu (p. 23) will be
overlaid on the image.
If you are previewing the final output image, the menu (p. 23) or
information about the settings (p. 26) will be overlaid on the image.
* If the connection cable you’re using has an RCA phono type plug, use
the included (or commercially available) RCA-BNC adaptors.
* The menu is shown when you press the [MENU] button (p. 10).
Ground Terminal
Use this to connect an external earth or ground.
☞
“About the ground terminal” (p. 15)
Cord Hook
Fasten the cord of the included AC adaptor to this hook so that
the cord will not be disconnected accidentally.
☞
“Connecting the AC Adaptor” (p. 15)
AC Adaptor Connector
Connect the included AC adaptor here.
☞
“Connecting the AC Adaptor” (p. 15)
[POWER] Switch
This turns the power on/off.
☞
“Turning the Power On/Off” (p. 20)
MIDI OUT/THRU Connector
You can switch the function of this connector between MIDI OUT
and MIDI THRU.
☞
“MIDI OUT/THRU connector setting” (p. 66)
●
MIDI OUT
This connector will transmit MIDI messages to an external device.
●
MIDI THRU
This connector will retransmit (without change) any MIDI
messages arriving at the MIDI IN connector.
Input/output
settings
MONITOR OUT PC/8 Connector (channel 8)
This is a BNC connector that outputs a composite video signal of
the image that is being input to the channel 8 S-video connector
or to the PC1/PC2 input connector.
Here you can connect a television monitor that has a composite
video input connector, and use it to view the input image.
* The input from the S-video connector will take priority for channel 8.
* If the connection cable you’re using has an RCA phono type plug, use
the included (or commercially available) RCA-BNC adaptors.
MIDI IN Connector
This connector receives MIDI messages from an external MIDI
device.
Security Slot ( )
You can attach a commercially available security lock here. For
details, refer to the following website:
http://www.kensington.com/
13
Connecting Peripheral Devices
Basic Connections
* To prevent malfunction and/or damage to video monitors or other devices, always turn off the power on all devices before making
any connections.
* Be sure to use cables and adapter plugs with the proper connectors matching those of the other devices you are using.
DVD player, Video tape recorder, DV camera
Video deviceComputer
VGA output
*1 Composite connectors can be one of two
types: RCA phono type and BNC type.
Before making connections, be sure to
check the type of plug on your connection
cable and the shape of the composite
connector.
If you want to connect an RCA phono type
cable to a BNC connector, you’ll need to
use the included (or commercially
available) RCA-BNC adaptor plugs.
RCA-BNC
adaptor plugs
connector
VGA cable
Ground
terminal
S-video cable
RCA-BNC
adaptor plugs
S-video output
connector
RCA-BNC
adaptor plugs
RCA-BNC
adaptor
plugs
Composite output
connector *1
Composite cable
V-8 Rear panel
RCA-BNC
adaptor plugs
Composite input
connector *1
Preview monitor
14
Composite cable Composite cable
S-video
cable
S-video
input
connector
Final
output device
Composite input
connector *1
Projector or TV monitor
Composite
input
connector *1
Monitor the
8/PC1/PC inputs
Composite cableComposite cable
Composite
input
connector *1
Monitor the
1–7 inputs
Connecting Peripheral Devices
●
About the composite connectors and MONITOR OUT connectors
The V-8’s composite inputs and outputs use BNC connectors. If your connection cables have RCA phono plugs, you’ll
need to use the included (or commercially available) RCA-BNC adaptor plugs.
●
About cable routing
Using an S-video cable will provide a higher-quality image. However, if the cable routing is very long, noise may
appear in the image. If this occurs, use a composite cable.
●
About the inputs
The S-video connector input will take priority for input channels 5–8.
●
About the final output
The same image is sent from all of the OUTPUT connectors (composite connectors and S-video connector).
●
About the ground terminal
Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that
the surface feels gritty to the touch when you touch this device. This is due to an infinitesimal electrical charge, which
is absolutely harmless. However, if you are concerned about this, connect the ground terminal with an external ground.
When the unit is grounded, a slight hum may occur, depending on the particulars of your installation. If you are unsure
of the connection method, contact the nearest EDIROL/Roland Service Center, or an authorized EDIROL/Roland
distributor, as listed on the “Information” page.
Unsuitable places for connection
•
Water pipes (may result in shock or electrocution)
•
Gas pipes (may result in fire or explosion)
•
Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
(continued)
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Connecting the AC Adaptor
* Place the AC adaptor so the side with the indicator (see illustration) faces upwards and the side with textual information
faces downwards. The indicator will light when you plug the AC adaptor into an AC outlet.
Indicator
Power cord (included)
AC Adaptor
Cord hook
(included)
* The shape of the power cord’s plug varies
depending on the country.
To prevent the inadvertent disruption of power to your unit
(should the plug be pulled out accidentally), and to avoid
applying undue stress to the AC adaptor connector, anchor
the power cord using the cord hook, as shown in the
illustration.
To power outlet
Input/output
settings
15
Connecting Peripheral Devices
Examples of Using the V-8
Events
In events that involve various types of exhibition or video performance, you can use the V-8 to switch between multiple
live video sources and the video from a DVD or computer.
(continued)
Input monitor
Output video device
Multi monitor
Computer
Output video device
DV camera
DVD player
●
Advantages of using the V-8
•
You can mix two video images (e.g., two live images, live image + DVD/computer image)
•
You can use the Picture In Picture effect to display two images simultaneously (p. 43).
•
Since a scan converter is built in, still images and the like from a computer can be input directly.
VGA
Composite
S-video
Composite
Composite
Composite
S-video
Preview monitor
Preview
Final output device
Large display
Projector
16
Connecting Peripheral Devices
(continued)
Concerts or VJ Performances
Images can be projected on a large screen located at the back of the stage to create a video performance that’s
synchronized to the music. You can mix images from a PR-50/80 or computer (VJ software) with multiple live images.
Output video device
Computer
Input monitor
MIDI
Multi monitor
Preview
Preview monitor
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Output video device
VGA
DV camera
PR-80/50
DVD player
●
Advantages of using the V-8
•
You can use the BPM Sync function to switch images in time with the music (p. 60).
•
You can combine multiple transition effects to create an original transition pattern (User Transition; p. 38).
•
You can use numerous effects such as Feedback, After-image, and Silhouette.
•
Since a scan converter is built in, video from a computer (VJ software) can be input directly. You can also
Composite
S-video
Composite
Composite
Final output device
Composite
S-video
use the V-8’s Zoom function to input just a portion of the image.
•
You can use the V-8’s [CONTROL] faders to dynamically apply an effect or fade to the input signal.
•
You can set the V-8 to Local Off, and use it to control the VJ software on your computer without affecting the
output image (Panel Mode; p. 67).
Projector
Input/output
settings
17
Connecting Peripheral Devices
Presentations
You can switch between photos or DVD output, or superimpose images or text from your computer.
Output video device
(continued)
Preview
Preview monitor
Computer
Output video device
DV camera
DVD player
●
Advantages of using the V-8
•
You can use the Picture In Picture effect to show two images simultaneously (p. 43).
•
You can use Luminance keying to superimpose text or graphics on an image (p. 46).
•
Since a scan converter is built in, you can directly input presentation material from your computer.
•
Since there are two PC inputs, you can connect and use two computers.
VGA
VGA
Composite
S-video
Composite
Composite
S-video
Final output device
Large display
Projector
18
Connecting Peripheral Devices
Background Video for a Musical Performance (Using V-LINK)
You can control background video (BGV) simultaneously while playing an instrument.
(continued)
Output video device
Computer
Output video device
VGA
DV camera
PR-80/50
●
Advantages of using the V-8
•
By using the V-8 in conjunction with the PR-50/80 you can control live video and images from the PR-50/80
Composite
S-video
MIDI
(V-LINK)
Composite
Preview
Preview monitor
Final output device
Composite
S-video
Projector
using just one device.
•
You can switch effects on/off from your instrument.
•
If you’re using V-LINK compatible devices, MIDI settings can be dramatically simplified.
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Using the V-8 with the RSS M-400 (Using V-LINK)
You can control the M-400 in synchronization with the switching of images.
Preview
Output video device
Preview monitor
Computer
Output video device
DV camera
PR-80/50
VGA
Composite
S-video
Composite
MIDI
(V-LINK)
Composite
S-video
M-400
Final output device
Projector
Input/output
settings
●
Advantages of using the V-8
•
Using V-LINK lets you synchronize the V-8’s video fader operations with the M-400’s audio input levels.
19
Basic Operation
Turning the Power On/Off
Turning the Power On
1
Make sure that the V-8 is correctly connected to your other equipment.
Press the [POWER] switch located on the V-8’s rear panel to turn it on.
fig.power-on-e.eps
2
On Off
V-8 Rear panel
Turning the Power Off
If you’ve used a menu operation (p. 24) to modify any parameters, close the menu before you turn off the power. If you turn
off the power before closing the menu, the changes you made will be discarded.
1
Press the [POWER] switch located on the V-8’s rear panel to turn it off.
20
Checking the Input and Output
Basic Operation
(continued)
fig.outputfade-up.eps
fig.input-select-e.eps
fig.video-fader-e.eps
Outputting Images
Here’s how to verify that the image is being correctly output to the TV monitor or projector connected to the OUTPUT
connector.
1
Power up your connected equipment and the V-8.
2
Play back your video device.
Input the image from the video device (camera, VTR, DVD player, etc.) or computer.
Raise the [OUTPUT FADE] fader.
3
4
Use the INPUT SELECT buttons to switch input channels.
If you’ve selected the [PC/8] button
Use the [PC INPUT SELECT] switch
to change between the PC1 and PC2
connector inputs.
Bus A Bus B
Press the INPUT SELECT button of a channel to which an image is being input. Verify that the image is correctly
shown on the television monitor or projector connected to the OUTPUT connector.
Try switching the input channel, and verify that the image shown in the television monitor or projector is switched
accordingly.
* The input from the S-video connector takes priority for channels 5–8.
Move the video fader to the bus A position.
Switch between inputs by successively pressing the INPUT SELECT
[1]–[PC/8] buttons for bus A.
Bus B
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Input/output
settings
Move the video fader to the bus B position.
Switch between inputs by successively pressing the INPUT SELECT
[1]–[PC/8] buttons for bus B.
Bus A
About the PC inputs
When you use the [PC INPUT SELECT] switch to switch the PC input, it will take some time for the input to stabilize.
We recommend that you use a monitor to verify the image.
In addition, selecting the PC input may cause the image display position to be skewed for some computers. Use the
PC input adjustment menu to adjust the screen display position. For details, refer to “Adjusting the PC Input Image”
(p. 54).
* When displaying moving images from a PC input, skew or flickering may occur in the image. For details, refer to
“Skewed or Flickering Images (Tearing)” (p. 55).
Blue Back Output
You can output a blue back to the final output image and to the preview of the final output image. Blue back output is
switched on/off using “No Signal Blueback” in the “Utility” menu.
Value Details
On
Off
* For details on menu operations, refer to “Menu Operations” (p. 23).
A blue back will be output when there is no signal.
A black image will be output when there is no signal.
21
Basic Operation
fig.preview-select.eps
(continued)
Outputting a Preview Image
Here’s how to verify that an image is correctly output to the TV monitor connected to the PREVIEW OUT connector that
you’re using for previewing.
1
Proceed as described in steps 1–3 of “Outputting Images” (p. 21).
2
Press the PREVIEW OUTPUT SELECT buttons to switch between preview output channels.
Press the PREVIEW OUTPUT SELECT button of a channel into which an image is being input. Verify that the image
is correctly shown in the television monitor (preview monitor) connected to the PREVIEW OUT connector.
Successively press the PREVIEW OUTPUT SELECT [1]–[PC/8] and [OUTPUT] buttons, and verify that the image in
the preview monitor is switched.
Sends the video being input via the INPUT 1–8/PC1/PC2connectors to the preview output.
[1]–[PC/8] buttons
[OUTPUT] button
* The image in the preview monitor will momentarily be distorted when you switch the preview output, but this will not
affect the final output.
* For channels 5–8, the input from the S-video connectors will take priority.
* Use the [PC INPUT SELECT] switch to change between the PC1/PC2 connector inputs.
Sends the final image to the preview output.
Preview output when there is no signal
With the factory settings, selecting a channel for which there is no input will cause the indication “No Signal” to appear
in the preview monitor. You can use the “Utility” menu item “Preview Signal Check” to turn the “No Signal” indication
on/off.
Value Details
The “No Signal” indication will be output when there is no signal.
On
Off
You can change the background color by setting the “Utility” menu item “Preview No Signal Color.”
* You can’t change the “No Signal” indication and background color for channel 8.
A black image will be output if there is no signal.
* For details on menu operations, refer to “Menu Operations” (p. 23).
Selecting the preview output
You can use the “Utility” menu item “Preview Switch Pattern” to change the way in which the preview output is
selected.
Value Details
Manual
Prev Auto
Always-1–8,
Always-Out
Auto1-2–1-8,
Auto1-Out
* For details on menu operations, refer to “Menu Operations” (p. 23).
The image selected by the PREVIEW OUT SELECT button will be sent to preview output.
The image of the bus (A or B) not being sent to the final output will be sent to preview output. For example,
if the bus A image is being sent to the final output, the bus B image will be sent to preview output.
The preview output will be fixed at channel 1–8 or at the final output.
While you hold down a PREVIEW OUT SELECT button, the image selected by the button will be sent
from the preview output.
The preview output will be switched automatically. For example, if you set this to “Auto1-4,” channels 1–4
will be switched automatically and sent to preview output.
You can use the “Utility” menu item “Preview Auto Speed” to change the time at which the preview output
is switched.
22
fig.connect-monitor-e.eps
Basic Operation
Menu Operations
By accessing menus you can make settings for the large variety of features, such as transitions and effects, that the V-8
offers.
For details on the menu items, refer to “Menu List” (p. 81).
Preparations for Viewing the Menu
The menu is shown on the TV monitor connected to the PREVIEW OUT connector. You’ll need to have your TV monitor
connected to the PREVIEW OUT connector and ready for use.
TV monitor
(continued)
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
fig.menu-images-e.eps
V-8 Rear panel
About menu levels
Menus are arranged as shown in the figure below. The value are set in the lowest level in each respective parameter.
Main menu
1. Mix (Trans1)
Value
001: Mix01, 002: Fam01, 003: Fam✽, ...
2. Wipe (Trans2)
Value
001: Mix01, 002: Fam01, 003: Fam✽, ...
3. Efx (Trans3)
Value
001: Mix01, 002: Fam01, 003: Fam✽, ...
Effects-A
Sub-menus Value
A-Efx1
A-Efx2
A-Efx3
A-Efx4
001: STILL1, 002: STILL2, ...
001: STILL1, 002: STILL2, ...
001: STILL1, 002: STILL2, ...
001: STILL1, 002: STILL2, ...
Input/output
settings
Effects-B
23
Basic Operation
fig.menu-preset.eps
fig.menu1.eps
fig.menu2.eps
(continued)
Operating the Menu
* The “Mem2” through “Mem8” indications at the right of the menu items indicate that settings will be stored in
[MEMORY] knob locations 2–8. If you want to change settings, turn the [MEMORY] knob to select the memory
number 2–8 whose settings you want to change. ☞ “Storing the Operating Panel Settings” (p. 28)
* If “Mem 1” (memory number 1) is indicated, you won’t be able to change the
contents, since these are the factory preset settings. The menu will indicate “
Preset ✽✽”.
1
Press the [MENU] button to access the menu.
2
Use the [ ] [ ] buttons to select a menu item.
✽✽
fig.menu3.eps
The [ ] [ ] buttons move the cursor up/down.
The menu item at the cursor will blink, indicated that it is selected.
3
Press the [ENTER] button to confirm your choice of menu item.
The selected menu item will be confirmed, and you’ll proceed to the next menu (a lower level).
To return to the previous menu (higher level), press the [MENU] button.
* If the menu level is deeper, repeat steps 2–3.
4
Use the [ ] [ ] buttons to edit the value.
5
Press the [MENU] button several times to close the menu.
While the menu is displayed, you can temporarily hide the menu by holding down the currently selected PREVIEW OUT
SELECT button.
24
fig.menu-protect.eps
Basic Operation
(continued)
Saving your settings
The content of your settings is saved in the V-8’s internal memory when you close the menu.
Be aware that if you edit settings and switch off the power before closing the menu, your changes will be lost.
Locking menu operations (Memory protect)
By turning the “Utility” menu item “Memory Protect” to the “On” setting, you can prevent changes to the settings.
If memory protect is on, the memory screen will indicate “✽Protect On✽.”
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Adjusting the menu display position
You can adjust the location in which menus and settings (p. 26) are shown in the preview monitor. To make this
adjustment, use the “Utility” menu items “OSD Horizontal Locate” (horizontal position) and “OSD Vertical Locate”
(vertical position).
Input/output
settings
25
Basic Operation
● symbol
Value of effect setting
Actual output Physical video fader position
● symbol
Bus output level
About the Current Settings Display
fig.preview-screen-e.eps
(continued)
You can use the preview monitor to view the current settings.
These settings are displayed only while the final output image is being sent to the preview output ([OUTPUT] button is lit).
Settings are not displayed while channels 1–8 are being sent to the preview output.
* You can change the contents of the information that will be displayed. The screen shown below is an example of
“Mode3,” which shows the most information about the settings. For details, refer to “Changing the Contents of the
Settings Display” (p. 27).
fig.preview-efx-e.eps
Preview output channel
BPM setting
“BPM SYNC” menu
“Speed” setting
Bus A effect setting and selection
●
(highlighted=selected)
status
Bus A [TRANSFORMER]
Bus A INPUT SELECT button selection Bus B INPUT SELECT button selection
button setting
Video fader position
Effect indication
[PC INPUT SELECT] switch setting
[MEMORY] knob selection
[WHITE/BLACK] switch setting
[OUTPUT FADE] fader position
Bus B effect setting and selection
(highlighted=selected)
status
TRANSITION button setting and
selection status
Bus B [TRANSFORMER]
button setting
(highlighted=selected)
If you’re able to use the [CONTROL] fader to change the effect
settings, a ● symbol is shown beside the effect name.
* For details on the effects whose settings you can control refer to
“Effects that can be controlled by the [CONTROL] faders”
(p. 42).
fig.preview-faderB.eps
fig.preview-fader-position-e.eps
fig.preview-fade-e.eps
●
Video fader position indication
This indication is shown when you’re using the BPM Sync function
(p. 60).
This indication is shown when the position of the video fader differs
from the actual output.
●
Bus fade indication
When the [CONTROL] faders can be used to fade the bus image
(p. 31), a ● symbol is shown beside the “FADE” indication.
• You can cause the settings to be hidden while you hold down the [OUTPUT] button.
• The settings display is not shown while the menu is displayed (p. 24).
26
Changing the Contents of the Settings Display
Here’s how to change the contents of the information shown in the preview monitor.
Basic Operation
(continued)
Press the [MENU] button to access the menu, and choose “Utility.”
1
fig.menu-utility.eps_18
Press the [MENU] button to access the menu.
Use the [ ] [ ] buttons to select “Utility.”
Press the [ENTER] button to confirm your selection.
2
Use the [ ] [ ] buttons to select “Preview Display Mode,” and press the [ENTER] button.
Use the [ ] [ ] buttons to select the contents of the information that will be shown in the
3
fig.menu-utl-prvdisp.eps_18
preview monitor.
Value No Display Mode1 Mode2 Mode3
Details
No settings will be
shown in the preview
monitor.
(Display example)
fig.preview-mode1.eps_13.5
(Display example)
fig.preview-mode2.eps_13.5
(Display example)
fig.preview-mode3.eps_13.5
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
Press the [MENU] button several times to close the menu.
4
Input/output
settings
27
Basic Operation
Storing the Operating Panel Settings ([MEMORY] Knob)
fig.memory-e.eps
(continued)
You can store the settings of the operating panel buttons and faders in memory locations 2–8 of the [MEMORY] knob. To
recall the stored settings, simply choose the desired memory number.
The factory preset settings are assigned to memory number 1. These settings are recall-only, and can’t be edited.
* The factory preset settings match the button names printed on the operating panel. For details on the settings, refer to
the section “Settings stored at the [MEMORY] knob,” later on this page.
1
2
3
4
5
6
7
8
Settings Stored at the [MEMORY] Knob
Settings for the following buttons and faders are stored at the [MEMORY] knob. The settings you edit are stored immediately
in the currently selected memory number. The on/off states of the EFFECTS buttons are also remembered.
Operating panel
TRANSITION
buttons
[BPM SYNC] button
Bus A EFFECTS
buttons
Bus B EFFECTS
buttons
Bus A [TRANSFORMER] button
Bus B [TRANSFORMER] button
[OUTPUT FADE] fader
PANEL MODE
[1 MIX]
[2 WIPE]
[3 EFX]
[1 (FEEDBACK)]
[2 (NEGATIVE)]
[3 (COLORIZE)]
[4 (MULTI)]
[1 (FLIP)]
[2 (CHROMA KEY)]
[3 (LUMINANCE KEY)]
[4 (P in P)]
Factory preset
(memory number 1)
001: Mix01
008: Wipe03
192: SWipe88
Mode: TransitionA/B
Speed: BPMx1
022: FEEDBACK
033: NEGATIVE
042: COLORIZE
126: MULTI-HV
102: FLIP
098: CHROMAKEY
096: B-LUMIKEY
150: PinP
02: Trans
02: Trans
02: Manual
01: Video + MidiOut
✽
✽
✽
✽
✽
✽
✽
✽
Stored setting
Transition effect assigned to each button. p. 36
Transition mode and displayed BPM when using BPM
sync (p. 60).
Effect setting assigned to each button. p. 53
Settings for operating the [TRANSFORMER] buttons. p. 41
Fade operation setting for the [OUTPUT FADE] fader. p. 78
Settings for whether MIDI messages will be
transmitted when buttons or faders are operated.
See
page
p. 62
p. 67
28
Basic Operation
Recalling a Memory
1
Turn the [MEMORY] knob to the memory number 1–8 that you want to recall.
The settings will be recalled.
fig.memory-dialset.eps
* Memory number 1 contains the factory preset settings (p. 28).
Copying the Contents of a Memory
Here’s how to copy the settings of the currently selected memory number to a different memory number.
1
Turn the [MEMORY] knob to select the desired copy-source memory number 1–8.
fig.memory-dialset.eps
* Memory number 1 contains the factory preset settings (p. 28).
(continued)
Introduction Connections Basic operation Switching images Effects BPM sync External devices Video fader Appendices
2
Press the [MENU] button to access the menu, and choose “Memory Edit.”
3
Use the [ ] [ ] buttons to select the desired copy-destination memory number, and press the
[ENTER] button.
4
Make sure that the display indicates “Push [ENTER],” and press [ENTER].
(If you decide to cancel, press the [MENU] button.)
The contents of memory will be copied.
fig.menu-memory.eps_18
Press the [MENU] button to access the menu.
Use the [ ] [ ] buttons to select “Memory Edit.”
Press the [ENTER] button to confirm your selection.
fig.menu-memory-c.eps_18
fig.memory-copy-e.eps
Copy-source memory number Copy-destination memory number
To copy the contents of memory, choose an item that shows “Copy” at the left
side. In the screen example shown here, the settings of memory number 2 will
be copied to memory number 6.
You can change the copy-source memory number at this time by turning the
[MEMORY] knob.
By choosing “Mem✽ -> All” you can copy the settings to all memory numbers
2–8.
Input/output
settings
Press the [MENU] button several times to close the menu.
5
29
Basic Operation
(continued)
Exchanging the Contents of Memories
Here’s how to exchange the contents of the currently selected memory number with a different memory number.
Turn the [MEMORY] knob to select the desired exchange-source memory number 2–8.
1
Press the [MENU] button to access the menu, and choose “Memory Edit.”
2
fig.memory-dialset.eps
* Memory number 1 contains the factory preset settings (p. 28). They cannot
be exchanged with the settings of another memory number.
fig.menu-memory.eps_18
Press the [MENU] button to access the menu.
Use the [ ] [ ] buttons to select “Memory Edit.”
Press the [ENTER] button to confirm your selection.
Use the [ ] [ ] buttons to select the desired exchange-destination memory number, and
3
press the [ENTER] button.
Make sure that the display indicates “Push [ENTER],” and press [ENTER].
4
(If you decide to cancel, press the [MENU] button.)
The contents of the two memories will be exchanged.
5
Press the [MENU] button several times to close the menu.
fig.menu-memory-e.eps_18
fig.memory-exchange-e.eps
Exchange-source memory number Exchange-destination memory number
To exchange the contents of memory, choose an item that shows “Exchange”
at the left side. In the screen example shown here, the settings of memory
number 2 will be exchanged with the settings of memory number 8.
You can change the exchange-source memory number at this time by turning
the [MEMORY] knob.
30
Loading...