Edirol CS-50 User Manual

Owner’s Manual

195mm

21mm

MICROPHONE CONNECTION CABLE

GNDMID +

SIDE -

21

3

GNDMID +

SIDE +

21

3

LEFT (GRAY)

RIGHT (RED)

LO CUT

FLAT

WIDE ST

FOCUS

LO CUT

FLAT

WIDE ST

FOCUS

WIND SCREEN

LOW-CUT SWITCH DIRECTIVITYSWITCH

XLR TYPE CONNECTOR
(5-pin)

CONNECTION CABLE

XLR TYPE CONNECTOR
(3-pin)

XLR TYPE CONNECTOR
(3-pin)

LEFT (GRAY)

RIGHT (RED)

MICHOLDER

MICSTAND

SCREWADAPTER

(5/8"—27,3/8"—16)

CAMERASHOE

MOUNTADAPTER

MEMO

We’d like to take a moment to thank you for purchasing the Stereo Shotgun
Microphone CS-50.

Before using this unit, carefully read the section entitled: “IMPORTANT
NOTES.” This section provides important information concerning the proper
operation of the unit. Additionally, in order to feel assured that you have gained
a good grasp of every feature provided by your new unit, this manual should be

■ IMPORTANT NOTES

• Howling could be produced depending on the location of microphones
relative to speakers. This can be remedied by:

1. Changing the orientation of the microphone(s).

2. Relocating microphone(s) at a greater distance from speakers.

3. Lowering volume levels.

• Protect the unit from strong impact. (Do not drop it!)

• Do not open or perform any internal modifications on the unit.

• Never use or store the unit in places that are:

• Subject to temperature extremes (e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top of heat-generating equipment); or are

• Damp (e.g., baths, washrooms, on wet floors); or are

read in its entirety. The manual should be saved and kept on hand as a
convenient reference.
Copyright © 2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.

• Humid; or are

• Exposed to rain; or are

• Dusty; or are

• Subject to high levels of vibration.

• When using the microphone with the stand recommended by Roland (ST­210 or ST-259), make sure the legs of the tripod are opened wide enough to
keep the equipment from falling over. The stand must be carefully placed so
it is level and sure to remain stable.

• For everyday cleaning wipe the unit with a soft, dry cloth or one that has
been slightly dampened with water. To remove stubborn dirt, use a cloth
impregnated with a mild, non-abrasive detergent. Afterwards, be sure to
wipe the unit thoroughly with a soft, dry cloth.

• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the
possibility of discoloration and/or deformation.

WARNING

• Keep the included Screw Adapter in a
safe place out of children’s reach, so
there is no chance of them being
swallowed accidentally.

■ FEATURES

• Shotgun microphone enables single-unit stereo acquisition

• Compact and lightweight for superior portability, perfect for field recording

• Two-position switch for wide stereo pickup (WIDE ST) or exceptional
directivity (FOCUS)

• Includes low end roll-off (high-pass filter) switch (cutoff frequency: 80 Hz)

• Condenser microphone (requires 11 to 52 V DC phantom power)

* Supply from plug required for both left and right channels

■ OPERATION

1. Connect the XLR connector (5-pin) to the microphone.

2. Connect the other ends of the cable to the inputs of the unit you use, such as
mixer.

3. If you wish to install the microphone to a microphone stand, use the supplied
mic holder. If the mic holder does not fit the stand, try exchanging the screw
adapter. (U 5/8, W 3/8)

■ LOW-CUT SWITCH

Cuts lower-range portions of the audio. Cutoff frequency is
80 Hz.
Switch to “LO CUT” to cut audio at 80 Hz and lower
frequencies.
The low end is not cut when this is switched to “FLAT.”

■ DIRECTIVITY SWITCH

Switches the directivity of the stereo mic.
In the “WIDE ST” position, the mic switches to a wide

stereo pickup pattern.
Switching to “FOCUS” raises the sensitivity at the front of
the mic, increasing the directivity.

■ PIN ASSIGNMENT

The pin assignment for XLR type connectors is as shown below.
Before making any connections, make sure that this pin assignment is
compatible with that of all your other devices.

■ POLAR PATTERNS

■ FREQUENCY RESPONSE

■ MAIN SPECIFICATIONS

Type .......................................................................................................Condenser

Frequency Response .....................................................................50—20,000 Hz

Output Impedance.......................................................................................200 Ω

Polar Patterns................................................................................Cardioid/FIG-8

Sensitivity ................................................................-36 dB (0 dB=1 V/Pa, 1 kHz)

Dimensions (diameter × length) ......................................................21 × 195 mm

Weight..............................................................................................................83 g

Accessories

Connection cable ............................................................................................1

Wind screen ....................................................................................................1

Carrying case ..................................................................................................1

Screw adapter (5.8"–27, 3/8"–16) ..................................................................1

Mic stand ........................................................................................................1

Mic holder ......................................................................................................1

Camera shoe mount adapter ...........................................................................1

* In the interest of product improvement, the specifications and/or appearance of

this unit are subject to change without prior notice.