Edimax Technology Co 9574791415 User Manual

Download

Page 1

AC1200 Wireless LAN 11ac

Dual-Band Concurrent

Wall Mount Access Point

User’s Manual

EW-7679WAUser Manual

05-2014 / v1.0

Version: 1.0

(October, 2014)

Page 2

CONTENTS

I. Product Information .............................................................................. 1

I-1. Package Contents ........................................................................................................ 1

I-2. System Requirements .................................................................................................. 2

I-3. Hardware Overview ..................................................................................................... 2

I-4. LED Status .................................................................................................................... 3

I-5. Reset ............................................................................................................................ 3

I-6. Magnetic Wall Mount .................................................................................................. 4

I-7. Console ........................................................................................................................ 5

I-8. Safety Information ....................................................................................................... 6

II. Quick Setup ........................................................................................... 7

II-1. Initial Setup .................................................................................................................. 7

II-2. Basic Settings ............................................................................................................... 9

II-3. Wi-Fi Protected Setup (WPS) ................................................................................... 13

III. Hardware Installation ........................................................................... 13

IV. Browser Based Configuration Interface ................................................. 14

IV-1. Information .............................................................................................................. 17

IV-1-1. System Information ................................................................................................. 17

IV-1-2. Wireless Clients ........................................................................................................ 21

IV-1-3. Wireless Monitor ..................................................................................................... 23

IV-1-4. Log ............................................................................................................................ 24

IV-2. Network Settings ..................................................................................................... 26

IV-2-1. LAN-Side IP Address ................................................................................................. 26

IV-2-2. LAN Port ................................................................................................................... 28

IV-2-3. VLAN ........................................................................................................................ 29

IV-3. Wireless Settings ...................................................................................................... 30

IV-3-1. 2.4GHz 11bgn ........................................................................................................... 30

IV-3-1-1. Basic ........................................................................................................................... 31

IV-3-1-2. Advanced ................................................................................................................... 34

IV-3-1-3. Security ...................................................................................................................... 36

IV-3-1-3-1. No Authentication ................................................................................................... 37

IV-3-1-3-2. WEP .......................................................................................................................... 38

IV-3-1-3-3. IEEE802.1x/EAP ........................................................................................................ 38

IV-3-1-3-4. WPA-PSK .................................................................................................................. 38

IV-3-1-3-5. WPA-EAP .................................................................................................................. 39

IV-3-1-3-6. Additional Authentication ....................................................................................... 39

IV-3-1-4. WDS ........................................................................................................................... 41

Page 3

IV-3-2. 5GHz 11ac 11an ....................................................................................................... 43

IV-3-2-1. Basic ........................................................................................................................... 43

IV-3-2-2. Advanced ................................................................................................................... 46

IV-3-2-3. Security ...................................................................................................................... 48

IV-3-2-4. WDS ........................................................................................................................... 50

IV-3-3. RADIUS ....................................................................................................................... 52

IV-3-3-1. RADIUS Settings ......................................................................................................... 53

IV-3-3-2. Internal Server ........................................................................................................... 54

IV-3-3-3. RADIUS Accounts ....................................................................................................... 56

IV-3-4. MAC Filter ................................................................................................................ 58

IV-3-5. WMM ......................................................................................................................... 60

IV-4. Management ........................................................................................................... 62

IV-4-1. Admin ....................................................................................................................... 62

IV-4-2. Date and Time .......................................................................................................... 65

IV-4-3. Syslog Server ............................................................................................................ 67

IV-4-4. I’m Here ................................................................................................................... 68

IV-5. Advanced ................................................................................................................. 69

IV-5-1. LED Settings ............................................................................................................. 69

IV-5-2. Update Firmware ..................................................................................................... 70

IV-5-3. Save/Restore Settings .............................................................................................. 72

IV-5-4. Factory Default ........................................................................................................ 75

IV-5-5. Reboot ..................................................................................................................... 76

V. Appendix ............................................................................................. 77

V-1. Configuring your IP address ..................................................................................... 78

V-1-1. Windows XP ............................................................................................................. 78

V-1-2. Windows Vista ......................................................................................................... 80

V-1-3. Windows 7 ............................................................................................................... 82

V-1-4. Windows 8 ............................................................................................................... 89

V-1-5. Mac .......................................................................................................................... 89

V-1-6. Glossary...................................................................................................................... 91

V-2. Hardware Specification ............................................................................................ 94

V-3. ENVIRONMENT & PHYSICAL .................................................................................... 94

Page 4

1. Access Point

2. Antennas x 2

3. Magnetic Wall Mount x 1

& Screws

4. Quick Installation Guide

5. Power Cord

6. Power Adapter

2 3 4 5 6

I. Product Information

I-1. Package Contents

Page 5

I-2. System Requirements

A 12V DC IN

B LAN 1 (PoE)

C LAN 2

D Reset

- Existing cable/DSL modem & router

- Computer with web browser for access point configuration

I-3. Hardware Overview

A. 12V DC port to connect the power adapter B. LAN port with Power over Ethernet (PoE PD, IN) C. LAN port with Power over Ethernet (PoE PSE, OUT) D. Reset the access point to factory default settings

Page 6

I-4. LED Status

LED Status

Description

Off

The access point is off.

Blue

The access point is on.

Amber

The access point is starting up.

I-5. Reset

If you experience problems with your access point, you can reset the device back to its factory settings. This resets all settings back to default.

1. Press and hold the reset button on the access point for at least 10 seconds

than release the button.

You may need to use a pin or similar sharp object to push the reset button.

2. Wait for the access point to restart. The access point is ready for setup

when the LED is blue.

Page 7

I-6. Magnetic Wall Mount

The access point includes a magnetic wall mount which requires some assembly.

1. Attach the two magnetic wall mount strips to your wall using the included

screws, as shown below.

2. Press the back of your access point firmly against the two wall mounted

magnetic strips, with the access point’s in the correct position, upright orientation as displayed above.

Ensure your access point is securely attached to the magnetic strips.

Page 8

I-7. Console

Baud Rate

115200

Data

8 bit

Parity

None

Stop

1 bit

Flow Control

None

The access point can be configured via the “Console” port located on the access point’s side panel using a terminal-emulation program (e.g. HyperTerminal).

Use the following configuration settings for terminal-emulation programs:

Page 9

I-8. Safety Information

In order to ensure the safe operation of the device and its users, please read and act in accordance with the following safety instructions.

1. The access point is designed for indoor use only; do not place the access point outdoors.

2. Do not place the access point in or near hot/humid places, such as a kitchen or bathroom.

3. Do not pull any connected cable with force; carefully disconnect it from the access point.

4. Handle the access point with care. Accidental damage will void the warranty of the access point.

5. The device contains small parts which are a danger to small children under 3 years old. Please keep the access point out of reach of children.

6. Do not place the access point on paper, cloth, or other flammable materials. The access point may become hot during use.

7. There are no user-serviceable parts inside the access point. If you experience problems with the access point, please contact your dealer of purchase and ask for help.

8. The access point is an electrical device and as such, if it becomes wet for any reason, do not attempt to touch it without switching the power supply off. Contact an experienced electrical technician for further help.

9. If you smell burning or see smoke coming from the access point or power adapter, then disconnect the access point and power adapter immediately, as far as it is safely possible to do so. Call your dealer of purchase for help.

10. Operating temperature when using power adapter is 0°C to 40°C,

Operating temperature when using PoE switch is 0°C to 50°C.

Page 10

II. Quick Setup

II-1. Initial Setup

1. Connect the access point to a computer via Ethernet cable.

2. Connect the power adapter to the access point’s 12V DC port and plug the

power adapter into a power supply using the included cable.

3. Please wait a moment for the access point to start up. The access point is

ready when the LED is blue.

4. Set your computer’s IP address to 192.168.2.x where x is a number in the

range 3 – 100. If you are unsure how to do this, please refer to V-1. Configuring your IP address for more information.

Please ensure there are no other active network connections on your computer (disconnect Wi-Fi connections and Ethernet cables).

5. Enter the access point’s default IP address 192.168.2.2 into the URL bar of

a web browser.

Page 11

6. You will be prompted for a username and password. Enter the default

username “admin” and the default password “1234”.

7. You will arrive the “System Information” screen shown below.

8. Next, please follow the instructions below in II-2. Basic Settings to

configure the access point’s basic settings.

For more advanced configurations, please refer to IV. Browser Based Configuration Interface.

Page 12

II-2. Basic Settings

The instructions below will help you to configure the following basic settings of the access point:

- LAN IP Address

- 2.4GHz & 5GHz SSID & Security

- Administrator Name & Password

- Time & Date

It is recommended you configure these settings before using the access point.

1. To change the access point’s LAN IP address, go to “Network Settings” >

“LAN-side IP Address” and you will see the screen below.

2. Enter the IP address settings you wish to use for your access point. You

can use a dynamic (DHCP) or static IP address, depending on your network

environment. Click “Apply” to save the changes and wait a few moments

for the access point to reload.

When you change your access point’s IP address, you need to use

the new IP address to access the browser based configuration interface instead of the default IP 192.168.2.2.

3. To change the SSID of your access point’s 2.4GHz wireless network(s), go

to “Wireless Setting” > “2.4GHz 11bgn” > “Basic”. Enter the new SSID for

your 2.4GHz wireless network in the “SSID1” field and click “Apply”.

Page 13

To utilize multiple 2.4GHz SSIDs, open the drop down menu labelled “Enable SSID number” and select how many SSIDs you require. Then enter a new SSID in the corresponding numbered fields below, before clicking “Apply”.

4. To configure the security of your access point’s 2.4GHz wireless

network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Security”. Select

an “Authentication Method” and enter a “Pre-shared Key” or “Encryption Key” depending on your choice, then click “Apply”.

If using multiple SSIDs, specify which SSID to configure using the “SSID” drop down menu.

5. Go to “Wireless Setting” > “5GHz 11ac 11an” and repeat steps 3 & 4 for

the access point’s 5GHz wireless network.

Page 14

6. To change the administrator name and password for the browser based

configuration interface, go to “Management” > “Admin”.

7. Complete the “Administrator Name” and “Administrator Password” fields

and click “Apply”.

8. To set the correct time for your access point, go to “Management” >

“Date and Time”.

9. Set the correct time and time zone for your access point using the drop

down menus. The access point also supports NTP (Network Time Protocol) so alternatively you can enter the host name or IP address of a time server. Click “Apply” when you are finished.

Page 15

You can use the “Acquire Current Time from your PC” button if

you wish to set the access point to the same time as your PC.

10. The basic settings of your access point are now configured. Please

refer to III. Hardware Installation for guidance on connecting your access point to a router or PoE switch.

Page 16

II-3.

III. Hardware Installation

1. Connect a router or PoE switch to the access point’s LAN 1 port using an

Ethernet cable. PoE switches must be connected to the access point’s LAN 1 port.

2. If you are using a router, then connect the power adapter to the access

point’s 12V DC port and plug the power adapter into a power supply.

3. If you are using a PoE (Power over

Ethernet) switch then it is not necessary to use the included power adapter, the access point will be powered by the PoE switch.

Do not use the power adapter if you are using a PoE switch.

4. Connect a local network client or switch to the access point’s LAN 2 port

as required.

The access point’s LAN 2 port can support another powered device(PD).

Page 17

IV. Browser Based Configuration Interface

The browser-based configuration interface enables you to configure the access point’s advanced features. The EW-7679WAC features a range of advanced functions such as MAC filtering, MAC RADIUS authentication, VLAN configurations, up to 32 SSIDs and many more. To access the browser based configuration interface:

1. Connect a computer to your access point using an Ethernet cable.

2. Enter your access point’s IP address in the URL bar of a web browser. The

access point’s default IP address is 192.168.2.2.

3. You will be prompted for a username and password. The default

username is “admin” and the default password is “1234”, though it was recommended that you change the password during setup (see II-2. Basic Settings).

If you cannot remember your password, reset the access point back to its factory default settings. Refer to I-5. Reset

4. You will arrive at the “System Information” screen shown below.

Page 18

5. Use the menu across the top and down the left side to navigate.

6. Click “Apply” to save changes and reload the access point, or “Cancel” to

cancel changes.

Please wait a few seconds for the access point to reload after you “Apply” changes, as shown below.

Page 19

7. Please refer to the following chapters for full descriptions of the browser

based configuration interface features.

Page 20

IV-1. Information

Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration.

IV-1-1. System Information

The “System Information” page displays basic system information about the access point.

Page 21

System

Model

Displays the model number of the access point.

Product Name

Displays the product name for reference, which consists of “AP” plus the MAC address.

Uptime

Displays the total time since the device was turned on.

Boot From

Displays information for the booted hardware, booted from either USB or internal

Page 22

memory.

Version

Displays the firmware version.

MAC Address

Displays the access point’s MAC address.

Management VLAN ID

Displays the management VLAN ID.

IP Address

Displays the IP address of this device. Click “Refresh” to update this value.

Default Gateway

Displays the IP address of the default gateway.

DNS

IP address of DNS (Domain Name Server)

DHCP Server

IP address of DHCP Server.

Wired LAN Port Settings

Wired LAN Port

Specifies which LAN port (1 or 2).

Status

Displays the status of the specified LAN port (connected or disconnected).

VLAN Mode/ID

Displays the VLAN mode (tagged or untagged) and VLAN ID for the specified LAN port. See IV-2-3. VLAN

Wireless 2.4GHz (5GHz)

Status

Displays the status of the 2.4GHz or 5GHz wireless (enabled or disabled).

MAC Address

Displays the access point’s MAC address.

Channel

Displays the channel number the specified wireless frequency is using for broadcast.

Transmit Power

Displays the wireless radio transmit power level as a percentage.

Wireless 2.4GHZ (5GHz) / SSID

SSID

Displays the SSID name(s) for the specified frequency.

Authentication Method

Displays the authentication method for the specified SSID. See IV-3. Wireless Settings

Encryption Type

Displays the encryption type for the specified SSID. See IV-3. Wireless Settings

VLAN ID

Displays the VLAN ID for the specified SSID. See IV-2-3. VLAN

Page 23

Additional Authentication

Displays the additional authentication type for the specified SSID. See IV-3. Wireless Settings

Wireless Client Isolation

Displays whether wireless client isolation is in use for the specified SSID. See IV-2-3. VLAN

Wireless 2.4GHZ (5GHz) / WDS Status

MAC Address

Displays the peer access point’s MAC address.

Encryption Type

Displays the encryption type for the specified WDS. See IV-3-1-4. WDS

VLAN Mode/ID

Displays the VLAN ID for the specified WDS. See IV-3-1-4. WDS

Refresh

Click to refresh all information.

Page 24

IV-1-2. Wireless Clients

Refresh time

Auto Refresh Time

Select a time interval for the client table list to automatically refresh.

Manual Refresh

Click refresh to manually refresh the client table.

2.4GHz (5GHz) WLAN Client Table

SSID

Displays the SSID which the client is connected to.

MAC Address

Displays the MAC address of the client.

Displays the total data packets transmitted by the specified client.

Displays the total data packets received by the specified client.

The “Wireless Clients” page displays information about all wireless clients connected to the access point on the 2.4GHz or 5GHz frequency.

Page 25

Signal (%)

Displays the wireless signal strength for the specified client.

Connected Time

Displays the total time the wireless client has been connected to the access point.

Idle Time

Client idle time is the time for which the client has not transmitted any data packets i.e. is idle.

Vendor

The vendor of the client’s wireless adapter is

displayed here.

Page 26

IV-1-3. Wireless Monitor

Wireless Monitor

Site Survey

Select which frequency (or both) to scan, and click “Scan” to begin.

Channel Survey Result

After a scan is complete, click “Export” to save the results to local storage.

Site Survey Results

Displays the channel number used by the specified SSID.

SSID

Displays the SSID identified by the scan.

MAC Address

Displays the MAC address of the wireless router/access point for the specified SSID.

Security

Displays the authentication/encryption type of the specified SSID.

Signal (%)

Displays the current signal strength of the SSID.

Type

Displays the 802.11 wireless networking standard(s) of the specified SSID.

Vendor

Displays the vendor of the wireless router/access point for the specified SSID.

Wireless Monitor is a tool built into the access

point to scan and monitor the surrounding wireless environment. Select a frequency and click “Scan” to display a list of all SSIDs within range along with relevant details for each SSID.

Page 27

IV-1-4. Log

Save

Click to save the log as a file on your local computer.

Clear

Clear all log entries.

Refresh

Refresh the current log.

The system log displays system operation information such as up time and connection processes. This information is useful for network administrators.

When the log is full, old entries are overwritten.

Page 28

The following information/events are recorded by the log:

 USB

Mount & unmount

 Wireless Client

Connected & disconnected Key exchange success & fail

 Authentication

Authentication fail or successful.

 Association

Success or fail

 Change Settings  System Boot

Displays current model name

 NTP Client  Wired Link

LAN Port link status and speed status

 Proxy ARP

Proxy ARP module start & stop

 Bridge

Bridge start & stop.

 SNMP

SNMP server start & stop.

 HTTP

HTTP start & stop.

 HTTPS

HTTPS start & stop.

 SSH

SSH-client server start & stop.

 Telnet

Telnet-client server start or stop.

 WLAN (2.4G)

WLAN (2.4G] channel status and country/region status

 WLAN (5G)

WLAN (5G) channel status and country/region status

 ADT

Page 29

IV-2. Network Settings

LAN-side IP Address

IP Address Assignment

Select “DHCP Client” for your access point to be assigned a dynamic IP address from your

router’s DHCP server, or select “Static IP” to

manually specify a static/fixed IP address for your access point (below).

Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration.

IV-2-1. LAN-Side IP Address

The “LAN-side IP address” page allows you to configure your access point on your Local Area Network (LAN). You can enable the access point to dynamically receive an IP address from your router’s DHCP server or you can specify a static IP address for your access point, as well as configure DNS servers.

The access point’s default IP address is 192.168.2.2.

Page 30

IP Address

Specify the IP address here. This IP address will be assigned to your access point and will replace the default IP address.

Subnet Mask

Specify a subnet mask. The default value is

255.255.255.0

Default Gateway

For DHCP users, select “From DHCP” to get default gateway from your DHCP server or “User-Defined” to enter a gateway manually. For static IP users, the default value is blank.

DNS Servers

Primary Address

DHCP users can select “From DHCP” to get primary DNS server’s IP address from DHCP or “User-Defined” to manually enter a value. For static IP users, the default value is blank.

Secondary Address

Users can manually enter a value when DNS server’s primary address is set to

“User-Defined”.

DHCP users can select to get DNS servers’ IP address from DHCP or manually

enter a value. For static IP users, the default value is blank.

Page 31

IV-2-2. LAN Port

Wired LAN Port Settings

Wired LAN Port

Identifies LAN port 1 or 2.

Enable

Enable/disable specified LAN port.

Speed & Duplex

Select a speed & duplex type for specified LAN

port, or use the “Auto” value. LAN ports can

operate up to 1000Mbps and full-duplex enables simultaneous data packets transfer/receive.

Flow Control

Enable/disable flow control. Flow control can pause new session request until current data processing is complete, in order to avoid device overloads under heavy traffic.

802.3az

Enable/disable 802.3az. 802.3az is an Energy Efficient Ethernet feature which disables unused interfaces to reduce power usage.

The “LAN Port” page allows you to configure the settings for your access point’s two wired LAN (Ethernet) ports.

Page 32

IV-2-3. VLAN

VLAN Interface

Wired LAN Port/Wireless

Identifies LAN port 1 or 2 and wireless SSIDs (2.4GHz or 5GHz).

VLAN Mode

Select “Tagged Port” or “Untagged Port” for

specified LAN interface.

VLAN ID

Set a VLAN ID for specified interface, if “Untagged Port” is selected.

Management VLAN

VLAN ID

Specify the VLAN ID of the management VLAN. Only the hosts belonging to the same VLAN can manage the device.

The “VLAN” (Virtual Local Area Network) enables you to configure VLAN settings. A VLAN is a local area network which maps workstations virtually instead of physically and allows you to group together or isolate users from each other. VLAN IDs 1 – 4094 are supported.

VLAN IDs in the range 1 – 4094 are supported.

Page 33

IV-3. Wireless Settings

Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration.

IV-3-1. 2.4GHz 11bgn

The “2.4GHz 11bgn” menu allows you to view and configure information for your access point’s 2.4GHz wireless network across four categories: Basic,

Advanced, Security and WDS.

Page 34

IV-3-1-1. Basic

The “Basic” screen displays basic settings for your access point’s 2.4GHz Wi-Fi network (s).

Page 35

2.4GHz Basic Settings

Wireless

Enable or disable the access point’s 2.4GHz wireless radio. When disabled, no 2.4GHz SSIDs will be active.

Band

Select the wireless standard used for the access point. Combinations of 802.11b,

802.11g & 802.11n can be selected.

Enable SSID Number

Select how many SSIDs to enable for the

2.4GHz frequency from the drop down menu. A maximum of 16 can be enabled.

SSID#

Enter the SSID name for the specified SSID (up to 16). The SSID can consist of any combination of up to 32 alphanumeric characters.

VLAN ID

Specify a VLAN ID for each SSID.

Auto Channel

Enable/disable auto channel selection. Auto channel selection will automatically set the

wireless channel for the access point’s 2.4GHz

frequency based on availability and potential interference. When disabled, select a channel manually as shown in the next table.

Auto Channel Range

Select a range from which the auto channel setting (above) will choose a channel.

Auto Channel Interval

Specify a frequency for how often the auto channel setting will check/reassign the wireless channel. Check/uncheck the “Change

channel even if clients are connected” box

according to your preference.

Channel Bandwidth

Set the channel bandwidth: 20MHz (lower performance but less interference), 40MHz (higher performance but potentially higher interference) or Auto (automatically select based on interference level).

BSS BasicRateSet

Set a Basic Service Set (BSS) rate: this is a series of rates to control communication frames for wireless clients.

Page 36

Channel

Select a wireless channel from 1 – 11 (1-13).

Channel Bandwidth

Set the channel bandwidth: 20MHz (lower performance but less interference), 40MHz (higher performance but potentially higher interference) or Auto (automatically select based on interference level).

BSS BasicRate Set

Set a Basic Service Set (BSS) rate: this is a series of rates to control communication frames for wireless clients.

When auto channel is disabled, select a wireless channel manually:

Page 37

IV-3-1-2. Advanced

2.4GHz Advanced Settings

Contention Slot

Select “Short” or “Long” – this value is used for contention windows in WMM (see IV-3-6.

WMM).

Preamble Type

Set the wireless radio preamble type. The preamble type in 802.11 based wireless communication defines the length of the CRC (Cyclic Redundancy Check) block for communication between the access point and roaming wireless adapters. The default value is “Short Preamble”.

Guard Interval

Set the guard interval. A shorter interval can improve performance.

These settings are for experienced users only. Please do not change any of the values on this

page unless you are already familiar with these functions.

Changing these settings can adversely affect the performance of your access point.

Page 38

802.11g Protection

Enable/disable 802.11g protection, which increases reliability but reduces bandwidth (clients will send Request to Send (RTS) to access point, and access point will broadcast Clear to Send (CTS), before a packet is sent from client.)

802.11n Protection

Enable/disable 802.11n protection, which increases reliability but reduces bandwidth (clients will send Request to Send (RTS) to access point, and access point will broadcast Clear to Send (CTS), before a packet is sent from client.)

DTIM Period

Set the DTIM (delivery traffic indication message) period value of the wireless radio. The default value is 1.

RTS Threshold

Set the RTS threshold of the wireless radio. The default value is 2347.

Fragment Threshold

Set the fragment threshold of the wireless radio. The default value is 2346.

Multicast Rate

Set the transfer rate for multicast packets or use the “Auto” setting.

Tx Power

Set the power output of the wireless radio. You may not require 100% output power. Setting a lower power output can enhance security since potentially malicious/unknown users in distant areas will not be able to access your signal.

Beacon Interval

Set the beacon interval of the wireless radio. The default value is 100.

Station idle timeout

Set the interval for keepalive messages from the access point to a wireless client to verify if the station is still alive/active.

Page 39

IV-3-1-3. Security

The access point provides various security options

(wireless data encryption). When data is encrypted, information transmitted wirelessly cannot be read by anyone who does not know the correct encryption key.

It’s essential to configure wireless security in order to prevent unauthorised access to your network.

Select hard-to-guess passwords which include combinations of numbers, letters and symbols, and change your password regularly.

Page 40

2.4GHz Wireless Security Settings

SSID Selection

Select which SSID to configure security settings for.

Broadcast SSID

Enable or disable SSID broadcast. When enabled, the SSID will be visible to clients as an available Wi-Fi network. When disabled, the SSID will not be visible as an available Wi-Fi network to clients – clients must manually enter the SSID in order to connect. A hidden (disabled) SSID is typically more secure than a visible (enabled) SSID.

Wireless Client Isolation

Enable or disable wireless client isolation. Wireless client isolation prevents clients connected to the access point from communicating with each other and improves security. Typically, this function is useful for corporate environments or public hot spots and can prevent brute force attacks on clients’ usernames and passwords.

Load Balancing

Load balancing limits the number of wireless clients connected to an SSID. Set a load balancing value (maximum 50).

Authentication Method

Select an authentication method from the drop down menu and refer to the information below appropriate for your method.

Additional Authentication

Select an additional authentication method from the drop down menu and refer to the information below (IV-3-1-3-6.) appropriate for your method.

IV-3-1-3-1. No Authentication

Authentication is disabled and no password/key is required to connect to the access point.

Disabling wireless authentication is not recommended. When disabled, anybody within range can connect to your device’s SSID.

Page 41

IV-3-1-3-2. WEP

Key Length

Select 64-bit or 128-bit. 128-bit is more secure than 64-bit and is recommended.

Key Type

Choose from “ASCII” (any alphanumerical character 0-9, a-z and A-Z) or “Hex” (any characters from 0-9, a-f and A-F).

Default Key

Select which encryption key (1 – 4 below) is the default key. For security purposes, you can set up to four keys (below) and change which is the default key.

Encryption Key 1 – 4

Enter your encryption key/password according to the format you selected above.

Key Length

Select 64-bit or 128-bit. 128-bit is more secure than 64-bit and is recommended.

WPA Type

Select from WPA/WPA2 Mixed Mode-PSK, WPA2 or WPA only. WPA2 is safer than WPA only, but not supported by all wireless clients. Please make sure your wireless client supports your selection.

Encryption

Select “TKIP/AES Mixed Mode” or “AES”

encryption type.

Key Renewal Interval

Specify a frequency for key renewal in minutes.

Pre-Shared Key

Choose from “Passphrase” (8 – 63

WEP (Wired Equivalent Privacy) is a basic encryption type. For a higher level of security consider using WPA encryption.

IV-3-1-3-3. IEEE802.1x/EAP

IV-3-1-3-4. WPA-PSK

WPA-PSK is a secure wireless encryption type with strong data protection and user authentication, utilizing 128-bit encryption keys.

Page 42

Type

alphanumeric characters) or “Hex” (up to 64 characters from 0-9, a-f and A-F).

Pre-Shared Key

Please enter a security key/password according to the format you selected above.

WPA Type

Select from WPA/WPA2 Mixed Mode-EAP, WPA2-EAP or WPA-EAP.

Encryption

Select “TKIP/AES Mixed Mode” or “AES”

encryption type.

Key Renewal Interval

Specify a frequency for key renewal in minutes.

IV-3-1-3-5. WPA-EAP

WPA-EAP must be disabled to use MAC-RADIUS authentication.

IV-3-1-3-6. Additional Authentication

Additional wireless authentication methods can also be used:

MAC Address Filter

Restrict wireless clients access based on MAC address specified in the MAC filter table.

See IV-3-5.MAC Filter to configure MAC filtering.

MAC Filter & MAC-RADIUS Authentication

Restrict wireless clients access using both of the above MAC filtering & RADIUS authentication methods.

MAC-RADIUS Authentication

Restrict wireless clients access based on MAC address via a RADIUS server, or password authentication via a RADIUS server.

See IV-3-4.RADIUS to configure RADIUS servers.

WPS must be disabled to use MAC-RADIUS authentication. See IV-3-3. for WPS settings.

Page 43

MAC RADIUS Password

Select whether to use MAC address or password authentication via RADIUS server. If

you select “Use the following password”, enter

the password in the field below. The password

should match the “Shared Secret” used in

IV-3-4. RADIUS.

Page 44

IV-3-1-4. WDS

Wireless Distribution System (WDS) can bridge/repeat access points together in an

extended network. WDS settings can be configured as shown below.

When using WDS, configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points, preferably on the WAN side.

WDS must be configured on each access point, using correct MAC addresses. All access points should use the same wireless channel and encryption method.

Page 45

2.4GHz

WDS Functionality

Select “WDS with AP” to use WDS with access point or “WDS Dedicated Mode” to use WDS and also block communication with regular wireless clients. When WDS is used, each access point should be configured with corresponding MAC addresses, wireless channel and wireless encryption method.

Local MAC Address

Displays the MAC address of your access point.

WDS Peer Settings

WDS #

Enter the MAC address for up to four other WDS devices you wish to connect.

WDS VLAN

VLAN Mode

Specify the WDS VLAN mode to “Untagged Port” or “Tagged Port”.

VLAN ID

Specify the WDS VLAN ID when “Untagged Port” is selected above.

WDS Encryption method

Encryption

Select whether to use “None” or “AES”

encryption and enter a pre-shared key for AES consisting of 8-63 alphanumeric characters.

Page 46

IV-3-2. 5GHz 11ac 11an

The “5GHz 11ac 11an” menu allows you to view

and configure information for your access point’s 5GHz wireless network across four categories: Basic, Advanced, Security and WDS.

IV-3-2-1. Basic

The “Basic” screen displays basic settings for your access point’s 5GHz Wi-Fi network (s).

Page 47

5GHz Basic Settings

Wireless

Enable or disable the access point’s 5GHz wireless radio. When disabled, no 5GHz SSIDs will be active.

Band

Select the wireless standard used for the access point. Combinations of 802.11a,

802.11n & 802.11ac can be selected.

Enable SSID Number

Select how many SSIDs to enable for the 5GHz frequency from the drop down menu. A maximum of 16 can be enabled.

SSID#

Enter the SSID name for the specified SSID (up to 16). The SSID can consist of any combination of up to 32 alphanumeric characters.

VLAN ID

Specify a VLAN ID for each SSID.

Auto Channel

Enable/disable auto channel selection. Auto channel selection will automatically set the wireless channel for the access point’s 5GHz frequency based on availability and potential interference. When disabled, select a channel manually as shown in the next table.

Auto Channel Range

Select a range from which the auto channel setting (above) will choose a channel.

Auto Channel Interval

Specify a frequency for how often the auto channel setting will check/reassign the

wireless channel. Check/uncheck the “Change channel even if clients are connected” box

according to your preference.

Channel Bandwidth

Set the channel bandwidth: 20MHz (lower performance but less interference), Auto 40/20MHz or Auto 80/40/20MHz (automatically select based on interference level).

BSS BasicRate Set

Set a Basic Service Set (BSS) rate: this is a series of rates to control communication frames for wireless clients.

Page 48

When auto channel is disabled, select a wireless channel manually:

Channel

Select a wireless channel.

Channel Bandwidth

Set the channel bandwidth: 20MHz (lower performance but less interference), Auto 40/20MHz or Auto 80/40/20MHz (automatically select based on interference level).

BSS BasicRate Set

Set a Basic Service Set (BSS) rate: this is a series of rates to control communication frames for wireless clients.

Page 49

IV-3-2-2. Advanced

5GHz Advanced Settings

Guard Interval

Set the guard interval. A shorter interval can improve performance.

802.11n Protection

DTIM Period

Set the DTIM (delivery traffic indication message) period value of the wireless radio. The default value is 1.

RTS Threshold

Set the RTS threshold of the wireless radio. The default value is 2347.

Fragment Threshold

Set the fragment threshold of the wireless radio. The default value is 2346.

These settings are for experienced users only. Please do not change any of the values on this

page unless you are already familiar with these functions.

Changing these settings can adversely affect the performance of your access point.

Page 50

Multicast Rate

Set the transfer rate for multicast packets or use the “Auto” setting.

Tx Power

Beacon Interval

Set the beacon interval of the wireless radio. The default value is 100.

Station idle timeout

Set the interval for keepalive messages from the access point to a wireless client to verify if the station is still alive/active.

Page 51

IV-3-2-3. Security

5GHz Wireless Security Settings

SSID Selection

Select which SSID to configure security settings for.

Broadcast SSID

The access point provides various security options (wireless data encryption). When data is encrypted, information transmitted wirelessly

cannot be read by anyone who does not know the correct encryption key.

It’s essential to configure wireless security in order to prevent

unauthorised access to your network.

Select hard-to-guess passwords which include combinations of numbers, letters and symbols, and change your password regularly.

Page 52

Wireless Client Isolation

and can prevent brute force attacks on clients’

usernames and passwords.

Load Balancing

Load balancing limits the number of wireless clients connected to an SSID. Set a load balancing value (maximum 50).

Authentication Method

Select an authentication method from the drop down menu and refer to the information below appropriate for your method.

Additional Authentication

Select an additional authentication method from the drop down menu and refer to the information below appropriate for your method.

Please refer back to IV-3-1-3. Security for more information on authentication and additional authentication types.

Page 53

IV-3-2-4. WDS

Wireless Distribution System (WDS) can bridge/repeat access points together in an extended network. WDS settings can be

configured as shown below.

When using WDS, configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points, preferably on the WAN side.

WDS must be configured on each access point, using correct MAC addresses. All access points should use the same wireless channel and encryption method.

Page 54

5GHz WDS Mode

WDS Functionality

Local MAC Address

Displays the MAC address of your access point.

WDS Peer Settings

WDS #

Enter the MAC address for up to four other WDA devices you wish to connect.

WDS VLAN

VLAN Mode

Specify the WDS VLAN mode to “Untagged Port” or “Tagged Port”.

VLAN ID

Specify the WDS VLAN ID when “Untagged Port” is selected above.

WDS Encryption

Encryption

Select whether to use “None” or “AES”

encryption and enter a pre-shared key for AES with 8-63 alphanumeric characters.

Page 55

IV-3-3. RADIUS

The RADIUS sub menu allows you to configure the

access point’s RADIUS server settings, categorized

into three submenus: RADIUS settings, Internal Server and RADIUS accounts.

A RADIUS server provides user-based authentication to improve security and offer wireless client control – users can be authenticated before gaining access to a network.

The access point can utilize both a primary and secondary (backup) RADIUS server for each of its wireless frequencies (2.4GHz & 5GHz). External RADIUS servers can be used or the access point’s internal RADIUS server can be used.

To use RADIUS servers, go to “Wireless Settings”  “Security” and select “MAC RADIUS Authentication”  “Additional

Authentication” and select “MAC RADIUS Authentication” (see IV-3-1-3. & IV-3-2-3).

Page 56

IV-3-4-1. RADIUS Settings

RADIUS Type

Select “Internal” to use the access point’s

built-in RADIUS server or “external” to use an external RADIUS server.

RADIUS Server

Enter the RADIUS server host IP address.

Authentication Port

Set the UDP port used in the authentication protocol of the RADIUS server. Value must be between 1 – 65535.

Shared Secret

Enter a shared secret/password between 1 – 99 characters in length. This should match the

“MAC-RADIUS” password used in IV-3-1-3-6 or IV-3-2-3.

Configure the RADIUS server settings for

2.4GHz & 5GHz. Each frequency can use an

internal or external RADIUS server.

Page 57

Session Timeout

Set a duration of session timeout in seconds between 0 – 86400.

Accounting

Enable or disable RADIUS accounting.

Accounting Port

When accounting is enabled (above), set the UDP port used in the accounting protocol of the RADIUS server. Value must be between 1 –

65535.

Internal Server

Check/uncheck to enable/disable the access point’s internal RADIUS server.

EAP Internal Authentication

Select EAP internal authentication type from the drop down menu.

IV-3-4-2. Internal Server

The access point features a built-in RADIUS server which can be configured as shown

below used when “Internal” is selected for “RADIUS Type” in the “Wireless Settings”  “RADIUS”  “RADIUS Settings” menu.

To use RADIUS servers, go to “Wireless Settings”  “Security” and select “MAC RADIUS Authentication”  “Additional

Authentication” and select “MAC RADIUS Authentication” (see IV-3-1-3. & IV-3-2-3).

Page 58

EAP Certificate File Format

Displays the EAP certificate file format: PCK#12(*.pfx/*.p12)

EAP Certificate File

Click “Upload” to open a new window and

select the location of an EAP certificate file to use. If no certificate file is uploaded, the internal RADIUS server will use a self-made certificate.

Shared Secret

Enter a shared secret/password for use between the internal RADIUS server and RADIUS client. The shared secret should be 1 – 99 characters in length. This should match the

“MAC-RADIUS” password used in IV-3-1-3-6 or IV-3-2-3.

Session Timeout

Set a duration of session timeout in seconds between 0 – 86400.

Termination Action

Select a termination-action attribute:

“Reauthentication” sends a RADIUS request to the access point, “Not-Reathentication” sends

a default termination-action attribute to the access point, “Not-Send” no termination-action attribute is sent to the access point.

Page 59

IV-3-4-3. RADIUS Accounts

The internal RADIUS server can authenticate up to 256 user accounts. The “RADIUS

Accounts” page allows you to configure and manage users.

Page 60

User Name

Enter the user names here, separated by commas.

Add

Click “Add” to add the user to the user

registration list.

Reset

Clear text from the user name box.

Select

Check the box to select a user.

User Name

Displays the user name.

Password

Displays if specified user name has a password (configured) or not (not configured).

Customize

Click “Edit” to open a new field to set/edit a

password for the specified user name (below).

Delete Selected

Delete selected user from the user registration list.

Delete All

Delete all users from the user registration list.

User Name

Existing user name is displayed here and can be edited according to your preference.

Password

Enter or edit a password for the specified user.

Edit User Registration List

Page 61

IV-3-5. MAC Filter

Mac filtering is a security feature that can help to prevent unauthorized users from

connecting to your access point.

This function allows you to define a list of network devices permitted to connect to the access point. Devices are each identified by their unique MAC address. If a device which is not on the list of permitted MAC addresses attempts to connect to the access point, it will be denied.

To enable MAC filtering, go to “Wireless Settings”  “2.4GHz

11bgn/5GHz 11ac 11an”  “Security”  “Additional Authentication” and select “MAC Filter” (see IV-3-1-3. & IV-3-2-3).

The MAC address filtering table is displayed below:

Page 62

Add MAC Address

Enter a MAC address of computer or network device manually e.g. ‘aa-bb-cc-dd-ee-ff’ or enter multiple MAC addresses separated with commas, e.g. ‘aa-bb-cc-dd-ee-ff,aa-bb-cc-dd-ee-gg’

Add

Click “Add” to add the MAC address to the MAC address filtering table.

Reset

Clear all fields.

Select

Delete selected or all entries from the table.

MAC Address

The MAC address is listed here.

Delete Selected

Delete the selected MAC address from the list.

Delete All

Delete all entries from the MAC address filtering table.

Export

Click “Export” to save a copy of the MAC filtering table. A new window will pop up for you to select a location to save the file.

MAC address entries will be listed in the “MAC Address Filtering Table”. Select an entry using the “Select” checkbox.

Page 63

IV-3-6. WMM

Background

Low Priority

High throughput, non time sensitive bulk data e.g. FTP

Best Effort

Medium Priority

Traditional IP data, medium throughput and delay.

Video

High Priority

Time sensitive video data with minimum time delay.

Voice

High Priority

Time sensitive data such as VoIP and streaming media with minimum time delay.

Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification based on the

IEEE 802.11e standard, which provides Quality of Service (QoS) features to IEE 802.11 networks. WMM prioritizes traffic according to four categories: background, best effort, video and voice.

Configuring WMM consists of adjusting parameters on queues for different categories of wireless traffic. Traffic is sent to the following queues:

Queues automatically provide minimum transmission delays for video, voice, multimedia and critical applications. The values can further be adjusted manually:

Page 64

CWMin

Minimum Contention Window (milliseconds): This value is input to the initial random backoff wait time algorithm for retry of a data frame transmission. The backoff wait time will be generated between 0 and this value. If the frame is not sent, the random backoff value is doubled until the value reaches the number defined by CWMax (below). The CWMin value must be lower than the CWMax value. The contention window scheme helps to avoid frame collisions and determine priority of frame transmission. A shorter window has a higher probability (priority) of transmission.

CWMax

Maximum Contention Window (milliseconds): This value is the upper limit to random backoff value doubling (see above).

AIFSN

Arbitration Inter-Frame Space (milliseconds): Specifies additional time between when a channel goes idle and the AP/client sends data frames. Traffic with a lower AIFSN value has a higher priority.

TxOP

Transmission Opportunity (milliseconds): The maximum interval of time an AP/client can transmit. This makes channel access more efficiently prioritized. A value of 0 means only one frame per transmission. A greater value effects higher priority.

Page 65

IV-4. Management

Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration.

IV-4-1. Admin

You can change the password used to login to the browser-based configuration interface here.

It is advised to do so for security purposes.

If you change the administrator password, please make a note of the new password. In the event that you forget this password and are unable to login to the browser based configuration interface, see I-5. Reset for how to reset the access point.

Page 66

Account to Manage This Device

Administrator Name

Set the access point’s administrator name. This is used to log in to the browser based configuration interface and must be between 4-16 alphanumeric characters (case sensitive).

Administrator Password

Set the access point’s administrator password. This is used to log in to the browser based configuration interface and must be between 4-32 alphanumeric characters (case sensitive).

Advanced Settings

Product Name

Edit the product name according to your preference consisting of 1-32 alphanumeric characters. This name is used for reference purposes.

Page 67

Management Protocol

Check/uncheck the boxes to enable/disable specified management interfaces (see below). When SNMP is enabled, complete the SNMP fields below.

SNMP Version

Select SNMP version appropriate for your SNMP manager.

SNMP Get Community

Enter an SNMP Get Community name for verification with the SNMP manager for SNMP-GET requests.

SNMP Set Community

Enter an SNMP Set Community name for verification with the SNMP manager for SNMP-SET requests.

SNMP Trap

Enable or disable SNMP Trap to notify SNMP manager of network errors.

SNMP Trap Community

Enter an SNMP Trap Community name for verification with the SNMP manager for SNMP-TRAP requests.

SNMP Trap Manager

Specify the IP address or sever name (2-128 alphanumeric characters) of the SNMP manager.

HTTP

Internet browser HTTP protocol management interface

HTTPS

Internet browser HTTPS protocol management interface

TELNET

Client terminal with telnet protocol management interface

SSH

Client terminal with SSH protocol version 1 or 2 management interface

SNMP

Simple Network Management Protocol. SNMPv1, v2 & v3 protocol supported. SNMPv2 can be used with community based authentication. SNMPv3 uses user-based security model (USM) architecture.

Page 68

IV-4-2. Date and Time

Date and Time Settings

Local Time

Set the access point’s date and time manually

using the drop down menus.

Acquire Current Time from your PC

Click “Acquire Current Time from Your PC” to

enter the required values automatically according to your computer’s current time and date.

You can configure the time zone settings of your access point here. The date and time of the

device can be configured manually or can be synchronized with a time server.

Page 69

NTP Time Server

Use NTP

The access point also supports NTP (Network Time Protocol) for automatic time and date setup.

Server Name

Enter the host name or IP address of the time server if you wish.

Update Interval

Specify a frequency (in hours) for the access point to update/synchronize with the NTP server.

Time Zone

Select the time zone of your country/ region. If your country/region is not listed, please select another country/region whose time zone is the same as yours.

Page 70

IV-4-3. Syslog Server

Syslog Server

Transfer Logs

Check/uncheck the box to enable/disable the use of a syslog server, and enter a host name, domain or IP address for the server, consisting of up to 128 alphanumeric characters.

Copy Logs to Attached USB Device

Check/uncheck the box to enable/disable copying logs to attached USB storage.

The system log can be sent to a server or to attached USB storage.

Page 71

IV-4-4. I’m Here

Duration of Sound

Set the duration for which the buzzer will sound when the “Sound Buzzer” button is clicked.

Sound Buzzer

Activate the buzzer sound for the above specified duration of time.

The access point features a built-in buzzer which can sound on command using the “I’m

Here” page. This is useful for network administrators and engineers working

in complex network environments to locate the access point.

The buzzer is loud!

Page 72

IV-5. Advanced

Power LED

Select on or off.

Diag LED

Select on or off.

Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration.

IV-5-1. LED Settings

preference.

The access point’s LEDs can be manually

enabled or disabled according to your

Page 73

IV-5-2. Update Firmware

The “Firmware” page allows you to update

the system firmware to a more recent

version. Updated firmware versions often offer increased performance and security, as well as bug fixes. You can download the latest firmware from the website.

Do not switch off or disconnect the access point during a firmware upgrade, as this could damage the device.

Page 74

Update Firmware From

Select to upload firmware from your local computer or from an attached USB device. (You must transfer a firmware file to the USB device first.)

Firmware Update File

Click “Browse” to open a new window to locate and select the firmware file in your computer.

Update

Click “Update” to upload the specified

firmware file to your access point.

Page 75

IV-5-3. Save/Restore Settings

The access point’s “Save/Restore Settings”

page enables you to save/backup the access point’s current settings as a file to your local computer or a USB device attached to the access point, and restore the access point to previously saved settings.

Page 76

Save / Restore Settings

Using Device

Select to save the access point’s settings to your local computer or to an attached USB device.

Save Settings to USB

Save Settings

Click “Save” to save settings and a new

window will open to specify a location to save the settings file. If saving settings to your computer or USB device, you can also

check the “Encrypt the configuration file with a password” box and enter a password to

protect the file in the field underneath, if you wish.

Restore Settings from USB

Restore Settings

Click the browse button to find a previously saved settings file on your computer or select a settings file from your USB device.

Page 77

Settings files located on your USB storage will automatically be displayed. Then click “Restore” to replace your current settings. If your settings file is encrypted with a

password, check the “Open file with password” box and enter the password in

the field underneath.

Page 78

IV-5-4. Factory Default

Factory Default

Click “Factory Default” to restore settings to the factory default. A pop-up window will appear and ask you to confirm.

If the access point malfunctions or is not responding, then it is recommended that you

reboot the device (see IV-5.5) or reset the device back to its factory default settings. You can reset the access point back to its default settings using this feature if the location of the access point is not convenient to access the reset button.

After resetting to factory defaults, please wait for the access point to reset and restart.

Page 79

IV-5-5. Reboot

Reboot

Click “Reboot” to reboot the device. A countdown will indicate the progress of the reboot.

If the access point malfunctions or is not responding, then it is recommended that

you reboot the device or reset the access point back to its factory default settings (see IV-5-4). You can reboot the access point remotely using this feature.

Page 80

V. Appendix

V-1. Configuring your IP address

The access point uses the default IP address 192.168.2.2. In order to access the browser based configuration interface, you need to modify the IP address of your computer to be in the same IP address subnet e.g. 192.168.2.x (x = 3 –

254).

The procedure for modifying your IP address varies across different operating systems; please follow the guide appropriate for your operating system.

In the following examples we use the IP address 192.168.2.10 though you can use any IP address in the range 192.168.2.x (x = 3 – 254).

Page 81

V-1-1. Windows XP

1. Click the “Start” button (it should be located in the lower-left corner of

your computer), then click “Control Panel”. Double-click the “Network and Internet Connections” icon, click “Network Connections”, and then double-click “Local Area Connection”. The “Local Area Connection Status” window will then appear, click “Properties”.

2. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10 Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

Page 82

Page 83

V-1-2. Windows Vista

1. Click the “Start” button (it should be located in the lower-left corner of

your computer), then click “Control Panel”. Click “View Network Status and Tasks”, then click “Manage Network Connections”. Right-click “Local Area Network”, then select “Properties”. The “Local Area Connection Properties” window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”.

2. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10 Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

Page 84

Page 85

V-1-3. Windows 7

1. Click the “Start” button (it should be located in the lower-left corner of

your computer), then click “Control Panel”.

2. Under “Network and Internet” click “View network status and tasks”.

3. Click “Local Area Connection”.

Page 86

4. Click “Properties”.

Page 87

5. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.

6. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10 Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

Page 88

V-1-4. Windows 8

1. From the Windows 8 Start screen, you need to switch to desktop mode.

Move your curser to the bottom left of the screen and click.

2. In desktop mode, click the File Explorer icon in the bottom left of the

screen, as shown below.

Page 89

3. Right click “Network” and then select “Properties”.

Page 90

4. In the window that opens, select “Change adapter settings” from the left

side.

5. Choose your connection and right click, then select “Properties”.

Page 91

6. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.

7. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10 Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

Page 92

V-1-5. Mac

1. Have your Macintosh computer operate as usual, and click on “System

Preferences”

2. In System Preferences, click on “Network”.

3. Click on “Ethernet” in the left panel.

4. Open the drop-down menu labeled “Configure IPv4” and select

“Manually”.

Page 93

5. Enter the IP address 192.168.2.10 and subnet mask 255.255.255.0. Click

on “Apply” to save the changes.

Page 94

V-1-6. Glossary Default Gateway (Access point): Every non-access point IP device needs to

configure a default gateway’s IP address. When the device sends out an IP

packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination.

DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network an IP address.

DNS Server IP Address: DNS stands for Domain Name System, which allows Internet servers to have a domain name (such as www.Broadbandaccess point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server keeps a database of Internet servers and their respective domain names and IP addresses, so that when a domain name is requested (as in typing "Broadbandaccess point.com" into your Internet browser), the user is sent to the proper IP address. The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you.

DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your existing phone lines to transmit data at high speeds.

Ethernet: A standard for computer networks. Ethernet networks are connected by special cables and hubs, and move data around at up to 10/100 million bits per second (Mbps).

IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP address consists of a series of four numbers separated by periods, that identifies a single, unique Internet computer host in an IP network. Example:

192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier.

The IP address is a 32-bit binary pattern, which can be represented as four

cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa” can be anything from 000 to 255, or as four cascaded binary numbers separated by “.”: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b”

can either be 0 or 1.

Page 95

A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1’s followed by consecutive trailing 0’s, such as

11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1’s. When both are represented side by side in their binary forms, all bits in the IP

address that correspond to 1’s in the network mask become part of the IP

network address, and the remaining bits correspond to the host ID.

For example, if the IP address for a device is, in its binary form,

11011001.10110000.10010000.00000111, and if its network mask is,

11111111.11111111.11110000.00000000 It means the device’s network address is

11011001.10110000.10010000.00000000, and its host ID is,

00000000.00000000.00000000.00000111. This is a convenient and efficient method for access points to route IP packets to their destination.

ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet access point located at the ISP's office.

ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations.

LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your home network is considered a LAN.

MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique

for each manufacturer), plus 3 bytes that are often used as the product’s

serial number.

Access point: An access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses.

Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured like an IP address. It is used to create IP address numbers used only within a

Page 96

particular network (as opposed to valid IP address numbers recognized by the Internet, which must be assigned by InterNIC).

TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data transmission over the Internet. Both TCP and UDP are transport layer protocol. TCP performs proper error detection and error recovery, and thus is reliable. UDP on the other hand is not reliable. They both run on top of the IP (Internet Protocol), a network layer protocol.

Web-based management Graphical User Interface (GUI): Many devices support a graphical user interface that is based on the web browser. This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control/configure or monitor the device being managed.

Page 97

V-2. Hardware Specification

V-3. ENVIRONMENT & PHYSICAL

Page 98

transmitted, transcribed, stored in a retrieval system, or translated into any language or computer

language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or

otherwise, without the prior written permission of this company

This company makes no representations or warranties, either expressed or implied, with respect to the

contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following their purchase, the buyer (and not this company, its distributor, or its dealer)

assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages

resulting from any defect in the software. Further, this company reserves the right to revise this

publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.

Page 99

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment.

This device is restricted to indoor use only.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not Intended for Use

None