How it Works
Edimax Technology Co
Loading...
9513001104
User Manual
92 pgs1.94 Mb0

Edimax Technology Co 9513001104 User Manual

Wireless Projector Server User Manual
Version 2.0
Table of Contents
Chapter I Product Introduction .................................................................................. 4
1-1 Package Contents ........................................................................................ 4
1-3 System Requirements ................................................................................. 7
Chapter II Using Projector Server ........................................................................... 17
2-3-1 Windows 95/98/Me IP address setup: ............................................... 20
2-3-2 Windows 2000 IP address setup: ....................................................... 22
2-3-3 Windows XP IP address setup: .......................................................... 24
2-3-4 Windows Vista IP address setup: ...................................................... 26
2-6 Using Client Software ................................................................................ 39
On-Screen Keyboard ................................................................................... 41
About............................................................................................................ 41
2-6-2 Start / Stop Projection .................................................................... 43
2-6-3 Quad-split Display ........................................................................... 44
2-6-4 Change Display Setting ................................................................. 45
2-11-1 ‘User Switch’ Button ....................................................................... 50
2-11-2 Use Remote Controller .................................................................... 52
Chapter III Configure Projector Server .................................................................. 53
3-5-1 ‘Basic’ Settings .................................................................................. 62
3-5-2 ‘Advanced’ Settings ........................................................................... 65
3-5-3 ‘Security’ Settings .............................................................................. 68
3-5-3-1 Encryption: Disabled ............................................................. 70
3-5-3-2 Encryption: WEP ................................................................... 72
3-5-3-3 Encryption: WPA pre-shared key .......................................... 74
3-5-3-4 ‘WPS’ Settings ........................................................................ 76
3-6-1 Configuration Tools ........................................................................... 82
3-6-2 Firmware Upgrade ............................................................................ 84
3-6-3 Reset ................................................................................................... 86
Chapter I Product Introduction
1-1 Package Contents
Thank you for purchasing this wireless projector server! Before you start to use this product, please check every item in the package. If any of them is missing, please ask your dealer of purchase for a new package.
Packaging List
Item No. 1
2 3 4 5
Name Quantity
Wireless Projector Server 1 A/C Adapter 1 Network Cable 1 Remote Controller 1 Rubber Foot Pad 4
6 7
8
Wireless Antenna 2 CR-2302 Lithium Battery
1 (Installed in Remote Controller) CD(Manual) 1
1-2 Safety Instructions
Please follow the following safety instructions when you’re using this wireless projector server, or you may damage this projector server and / or yourself!
1. THIS PROJECTOR SERVER IS NOT A TOY! Keep out of reach of children!
2. Do not place this wireless projector server in humid and / or hot environment, like bathroom or kitchen. Please refer to the specification of this wireless projector server to understand the environmental requirements of this wireless projector server.
3. This wireless projector server is designed to be used indoor. Do not use this wireless projector server at places like garden or any other outdoor environment.
4. Do not put any part or any component, accessories of this projector server into your body.
5. If any part or any component is dropped into water, return it to your dealer of purchase and ask for an examination; never use it again before it has been properly processed by certified technician.
6. If the projector server is dropped into water when it’s powered on, DO NOT ATTEMPT TO GET IT BACK BY YOURSELF! Switch the electrical power switch off, and call a qualified electrical technician or us immediately for help.
7. If you want to hang this wireless projector server at high places, please make sure that the wireless projector server is properly secured. Falling down from high places will damage this wireless projector server, and may cause serious injury to people!
8. Do not drag any connected cord with force; the terminal and cord will be damaged.
9. Only use dry cloth with water to clean this wireless projector server; do not use alcohol or other chemical solution to clean this wireless projector server.
10. There’s no user-serviceable part inside this wireless projector server; if the wireless projector server is not working properly, please contact the dealer of purchase to ask for help.
11. Do not put the wireless projector server and / or A/C adapter on paper, cloth, or other flammable materials. After hours of use, this projector server w ill become hot, and may cause flammable materials placed under it to burn.
12. Do not cover the wireless projector server with cloth or any material; the projector server will become overheat and cause malfunction, even cause fire.
13. When the projector server is powered on, do not connect or disconnect any connection cable.
14. Do not display the same video content on projector, CRT / LCD display, and plasma TV for too long time. The image may remain PERMENTALY. Use screen saver to prevent to display the same video content for too long time.
15. If you smell something strange or even see smoke coming out from the wireless projector server or A/C adapter, disconnect the power cord immediately, and call your dealer of purchase for help.
1-3 System Requirements
Video Display:
A Projector, CRT display, LCD display, or plasma TV that support VGA
video input.
The display should support at least one resolution listed below:
800 x 600 1024 x 768 1280 x 800
Audio amplifier or speaker that accepts 3.5 audio connector.
Computers support wired or wireless Ethernet connectivity.
Windows 95 / 98 / Me / 2000 / XP / Vista / Windows 7 operating system or
MAC OSX 10.5 / 10.6 (Power PC exclusive) with Internet Explorer 5.5, Netscape, Safari, Firefox web browser.
At least 100MB of available hard disk space.
NOTE: Please check the user manual or specification of the display you’re going to use with this projector server for supported resolution. Using an unsupported resolution may damage your projector, CRT / LCD display, or plasma TV.
1-4 Highlights of this Wireless Projector Server
Thanks again for choosing this wireless projector server. This projector server eases the procedure of sharing a single projector among many presenters; they don’t have to switch VGA video cables, just use wired or wireless network connection to connect the projector server, and the video on their computer display will be projected on big-screen.
Other functions of this wireless projector server include:
Supports both wired (10/100Mbps Ethernet connection) and wireless
(802.11b / g / n 11Mbps / 54Mbps / 300Mbps connection).
Wireless interface supports encryption - protects the content of
presentation from theft.
Presenter needs to input a random 4-digit projector server access code as
2nd level security check.
WPS (Wi-Fi Protected Setup) function provides fast, easy, and secure
wireless encryption setup.
No pre-installed software required – new users can download application
from projector server directly, and get it installed within 30 seconds.
Works with any projector, LCD / CRT display, plasma display with VGA
video input.
Supports all major LCD display / projector resolutions – 800 x 600 / 1024 x
768 / 1280 x 800 or 1400 x 1050. Also supports audio output! Presenter can use supplied IR remote controller to control the process or
presentation. USB port - You can connect external peripherals to assist your
presentation, like wireless mouse. Broadcast to more than 2 projector servers for computer desktop or
images. USB port type B - You can connect to PC for direct display.(Only works in
Windows)
1-5 Familiar with Wireless Projector Server / Remote Controller
Front
USB Type B
Name Description Power Press this button to switch this projector server on / off. WPS WPS (Wi-Fi Protected Setup) activation button Remote Controller Receiver Power LED When this LED lights, indicates this wireless projector
LAN When this LED lights, indicates wired LAN is connected. WLAN When this LED flashes, indicates wireless LAN activity. USB Connector Connects to USB peripherals, supports USB mouse.
IR signal receiver (for remote controller), DO NOT block the receiver, or remote controller will not function.
server is correctly powered.
USB Type B Connects to PC or NB for direct projection without login.
(only works in Windows)
Back
Name Reset When this projector server is not working properly, you
VGA VGA D-sub 15 pin video output (Connects to any
Audio Stereo audio output (Connects to external speaker or
External IR Connects to supplied IR extender cable to receive IR
LAN 10/100Mbps fast Ethernet port (Connects to your local
Description
can use a pen or pin to press and hold this button for 5 seconds to reset the projector server.
VGA-compatible display).
audio amplifier).
signals
area network)
12VDC Connect to DC 12V power adapter (Use supplied A/C
power adapter only!). Antenna (Left and Right)
Transmits wireless signal. Please keep both antennas
perpendicular to the ground for best signal reception.
Remote Controller - Front
Name Description ‘Black out’ Button Press this button to activate ‘Black Out’ function, which
will remove any display contents displayed on external
display; Press this button again to resume. ‘Menu’ Button Press this button to switch the display output of projector
server between presenter’s computer display content
and projector server’s configuration menu. ‘Page down’ button ‘Page up’ button Equivalent to ‘Right’ key on your computer’s keyboard. ‘Prev.’ button Select previous user (presenter) in projector server’s
Equivalent to ‘Left’ key on your computer’s keyboard.
configuration menu; Equivalent to ‘Up’ key on your
computer’s keyboard when presentation is in progress. ‘Next’ button Select next user (presenter) in projector server’s
configuration menu; Equivalent to ‘Down’ key on your
computer’s keyboard when presentation is in progress. button Select user in projector server’s configuration menu.
Remote Controller - Top
IR Transmitter
Name Description IR Transmitter Infrared signal transmitter. When using the remote
controller, point the IR transmitter to the front of the
projector server. DO NOT use your finger or other object
to block the IR transmitter, or your command will not be
received by projector server.
Remote Controller - Back
Battery Lid
Name Description Battery Lid Press battery lid and push it out to open battery
compartment (to install or remove CR-2032 lithium
battery).
1-6 Install Wireless Projector Server
Please follow the following instructions to get the projector server installed:
1. Unpack the wireless projector server’s package, and make sure no item in the package is missing.
2. Connect antennas to both antenna connectors located at the back or projector server - hold antenna base by your finger and turn in clockwise direction to fasten it.
3. Connect the Ethernet cable to the LAN port (this port is labeled as ‘LAN’ and located at the back of this projector server)
4. Insert the audio cable which connects with external amplifier / speaker to ‘Audio Out’ port located at the back of this projector server.
You can skip this step if you don’t have external audio amplifier / speaker.
5. Insert VGA cable which connects with external video display to VGA connector located at the back of this projector server.
6. Adjust the antennas located at the back of the projector server, so they’re perpendicular to the ground.
7. Connect the A/C power adapter to the electrical outlet on the wall, and insert the power connector of A/C power adapter to the power slot labeled as ‘12VDC’
at the back of projector server.
9. Press ‘Power’ button located at the front of projector server.
10. Open battery lid located at the back of remote controller by press and push it downward, and place the CR 2032 battery into remote controller’s battery compartment. Please note that ‘+’ sign on the battery should be facing up. To close battery lid, push it back.
11. Please check the status of the ‘Power’ LED located at the front of the projector server. If it does not light, pl ease check all connections and the status of electrical power outlet, or refer to chapter 4-1 ‘Troubleshooting’ for possible solutions.
Chapter II Using Projector Server
2-1 Switch the Projector Server On and Check IP address
When the connection between projector server and external display is established, you can switch the display’s power on, then press the ‘Power’ button of projector server, which is located at the front of projector server.
You should be able to see the following image displayed on external display; if not, please make sure the external display you used with projector server accepts input video resolution ‘1024 x 768’, and horizontal refresh rate ‘60Hz’.
*
If you see above image shown on display for more than two minutes, please press ‘Power’ button to switch the projector server off, and then switch the projector server on again. If this still happens, refer to chapter 4-2 ‘Troubleshooting’ for possible solutions.
When the projector server is powered on and connected to a LAN with DHCP server, it will get an IP address from DHCP server automatically; when there’s no DHCP server available, it will use default IP address ‘169.254.0.200’. Please refer to chapter 2-3 ‘How to set IP address for your computer’ to set the IP address for computers wish to connect to projector server when there’s no DHCP server available.
The IP address of projector server can be found on the connected external display, like following picture:
The IP Address (Wireless / Wired Ethernet) of projector server can be found here.
The IP address of the WLAN (wireless Ethernet) and LAN (wired Ethernet) interface of projector server can be found at the lower-left corner of video display. You can use one of these IP addresses to connect to the projector server.
2-2 Connect to Projector Server by Wireless Ethernet
The wireless Ethernet interface of this projector server is switched on and accepts any computer to establish connection by default. You can use your computer’s wireless utility to establish connection with this projector server.
The SSID (Service Set Identifier) of this projector server is ‘projector’ by default:
Please select the wireless network named ‘projector’, and click ‘Connect’ to establish connection. In some cases, Windows will connect to projector server automatically, or sometime it will connect to other wireless network. Please make sure you’re connecting to correct wireless network.
After you connected to projector server, please use web browser to connect to projector server’s wireless (WLAN) IP address. In the following example, projector server’s IP address is ’10.30.40.1’, which is default setting.
2-3 Set the IP address of the Computer
If there’s no DHCP server available on your LAN, please follow the following instructions to set the IP address of the computer, so the computers wish to use the projector server can connect to project server.
If the operating system of your computer is….
Windows 95/98/Me - please go to section 2-3-1
Windows 2000 - please go to section 2-3-2 Windows XP - please go to section 2-3-3 Windows Vista - please go to section 2-3-4 Windows 7 - please go to section 2-3-5
2-3-1 Windows 95/98/Me IP address setup:
1. Click ‘Start’ button (it should be located at lower-left corner of your
computer), then click control panel. Double-click Network icon, and Network window will appear. Select ‘TCP/IP’, then click ‘Properties’.
2. Select ‘Specify an IP address’, then input the following settings in respective field:
IP address: 169.254.0.x (where x is an integer greater or less than 200, if there’s more than one computer need to use this projector server on the same network, every computer should use an unique number)
Subnet Mask: 255.255.255.0
click ‘OK’ when finish.
2-3-2 Windows 2000 IP address setup:
1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Dial-up
Connections icon, double click Local Area Connection, and Local Area Connection Properties window will appear. Select ‘Internet Protocol
(TCP/IP)’, then click ‘Properties’
2. Select ‘Use the following IP address’, then input the following settings in respective field:
IP address: 169.254.0.x (where x is an integer greater or less than 200, if there’s more than one computer need to use this projector server on the same network, every computer should use an unique number)
Subnet Mask: 255.255.255.0
click ‘OK’ when finish.
2-3-3 Windows XP IP address setup:
1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet
Connections icon, click Network Connections, and then double-click Local Area Connection, Local Area Connection Status window will appear, and
then click ‘Properties’
2. Select ‘Use the following IP address’, then input the following settings in respective field:
IP address: 169.254.0.x (where x is an integer greater or less than 200, if there’s more than one computer need to use this projector server on the same network, every computer should use an unique number)
Subnet Mask: 255.255.255.0
click ‘OK’ when finish.
2-3-4 Windows Vista IP address setup:
1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, then click Manage Network Connections..Right-click Local Area Netwrok, then select ‘Properties’. Local Area Connection Properties window will appear, select ‘Internet Protocol Version 4 (TCP / IPv4), and then click ‘Properties’
2. Select ‘Use the following IP address’, then input the following settings in respective field:
IP address: 169.254.0.x (where x is an integer greater or less than 200, if there’s more than one computer need to use this projector server on the same network, every computer should use an unique number)
Subnet Mask: 255.255.255.0
click ‘OK’ when finish.
Loading...
+ 64 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use