1. Do not place the product near water or in humid and / or hot environment,
like bathroom or kitchen. Please refer to the specification of the environment.
2. This product is designed to be used indoor.
3. Avoid swallowing any parts, components, or accessory of this product.
4. If this product is dropped into water when it‟s powered on, DO NOT
ATTEMPT TO RETRIEVE BACK BY YOURSELF! Switch the electrical power
switch off first, and call a qualified electrical technician for help.
5. If to hang this product, please make sure placement is properly secured.
Misplacement would cause falling and damage this product and injury to
people!
6. Do not drag any connected cord with force; the terminal and cord will be
damaged.
7. Only use dry cloth with water to clean this product; do not use alcohol or
other chemical solution to clean this product.
8. Do not repair, disassemble, or modify the product; if the product is not
working properly, please contact the dealer of purchase.
9. Do not put the product and / or A/C adapter directly on paper, cloth, or other
flammable materials. After hours of use, this product will become hot, and may
cause flammable materials placed under it to burn.
10. Do not cover the product with cloth or any material; the product will
become overheat and cause malfunction, even cause fire.
11. When the product is powered on, do not connect or disconnect any
connection cable.
12. If not using the product for a long time, please unplug A/C adapter from
wall socket, and remove the battery inside remote controller.
Chapter I Product Introduction
(1) WPG-350
(2) AC adapter
(3) Remote controller
(4) IR receiver extension cord
(5) AC adapter extension cord
(6) VGA cord
(7) Quick Installation Guide
(8) Software CD-ROM
(9) USB CABLE
Congratulations on your purchase of ViewSonic Wireless Presentation
Gateway WPG-350. This section introduces you to the WPG-350 (referred to
as the WPG in this user guide).
1-1 Package Contents
1-2 Requirements
PC CPU
Speed
Intel Pentium 4/1.5 GHz or higher
(Recommend Intel Core 2 Duo CPU For Video Playback
Mode)
Memory
512 MB of RAM or higher
(Recommend 1GB of RAM For Video Playback Mode)
Operating
System
Windows XP 32 bit or above
(Recommend Windows XP 32 bit)
MAC OS X 10.4 and 10.5
(Both PowerPC / Intel Version)
Network
100Mbps Wired Fast Ethernet /
11Mbps 802.11b wireless Ethernet
(Recommend 54Mbps 802.11g wireless Ethernet)
1-3 Highlights
Thanks again for choosing the product. This product allows multiple users to
connect to the same projector by wired or wireless network and avoiding the
hassle of using VGA cable.
Features
1. 802.11 b/g/n Wireless compatibility.
2. Supports both Wireless and Ethernet connectivity
3. VGA connections
4. Conference control
5. Supports multiple users at the same time with Quarter split screen
6. WPS (Wi-Fi Protected Setup)
7. Output Resolution: 1024x768 or 800x600.
8. Upgrade software via the Internet.
9. Network security.
10. Presentation remote
11. Video capture, to capture screen image for projection*
*This function will be available in Q4, 2009 via upgrade through Internet.
1-4 Part Names
Item No.
Description
1
WPS: Single Click when the
device is ON.
Turn On: Single Click when
the device is OFF.
2
„POWER‟ LED
3
„LAN‟ LED
4
„WIRELESS‟ LED
5
„PC IN‟ LED
Name
Description
12V
Connect to A/C adapter /
ViewSonic projector’s D/C
power outlet(device need to
be “ON” when plug the
power)
LAN
10/100/1000Mbps fast
Ethernet port
IR IN
Connect to IR receiver
Audio Out
Stereo audio output
VGA OUT
VGA video output
Antenna
Receives wireless signal.
USB 1
USB TYPE MINI B With
USB Cable display(may
not ready on MAC when
1st MP)
1
2 - 5
Front View
Back View
USB 2
USB TYPE A With Mouse
Control Function(will add
PC less function in the
future)
Name
Description
PC IN
Connect to computer‟s
VGA output port
Item No.
Description
1 Power
Stand-by mode on/off
2 Login
Show user list: Single Click.
2
WPS: Press and hold for 3
seconds.
3 Prev.user
Move up to select user for
presentation
4 Next user
Move down to select user for
presentation
5 Page up
Go to previous page
6 Page down
Go to next page
7 Confirm
Confirm selected user for
presentation
8 Battery Lid
Press battery lid and push it
Note:
1) WPS stands for Wi-Fi Protected Setup.
Side View
Remote Controller
downward by your thumb to open
battery compartment
9 IR LED
Infrared signal transmitter
1
2
3
5 7 6
4
8
9
Note:
1) Remote controller effective distance is 7 meters. This distance will be shortened
in some environments, or when the battery is low.
2) If there’s strong light source near WPG and / or remote controller, remote
controller may not be able to function properly.
1-5 Initial Setup
Connect one end of the VGA cable
to the external display, and the
other to WPG VGA-out port locates
at back.
Connect the Ethernet cable to the
LAN port
Connect audio cable to WPG
Audio-out Port locate at the back,
and the other end to an external
amplifier / speaker.
Connect the IR receiver extending
cable to „IR IN‟ port located at the
back of WPG, and place the IR
receiver at a place where you can
point the remote controller to it
easily
Step-by-step setup instructions
Adjust the antennas so they are
perpendicular to the ground.
Connect the A/C power adapter to
the electrical outlet on the wall.
Connect A/C power adapter to the
power jack labeled as „12V‟ at the
back of WPG.
To fix the product placement, please
use two wall mount holes located at
the back of the product.
If you can see this start screen
display on projector, indicates
WPG-350 is working and all
connection cables are correctly
connected.
Note:
DO NOT USE VELCRO STICKER ALONE TO FIX THE PRODUCT ON THE
WALL!
Chapter II Using WPG
The IP Address (Wireless / Wired Ethernet)
of the device.
2-1 Check the IP address of WPG
When WPG is powered on, check the connected display, you can find the IP
address and login code Instruction Page:
You can connect to WPG by the IP address of the connection type you‟re using
(wired / wireless).
2-2 Connect to WPG by wireless network
Use your computer‟s Wireless Network Connection window to access an
available wireless network. Select the device from the list. Click Connect. The
default device name is WPG-350.
Note: If using a wireless client other than Windows, the screen above may look
differently. For more details, see your PC user guide.
2-3 Manual Network Connection Setting
If there‟s no DHCP server available on your LAN, please follow the following
instructions to set the IP address of the computer.
If the operating system of your computer is….
Windows XP - please go to section 2-3-1
Windows Vista - please go to section 2-3-2
Macintosh - please go to section 2-5-4
2-3-1 Windows XP IP address setup:
Click „Start‟ from windows toolbar
locate at bottom, open control panel,
then select Network and Internet
Connections, click Network
Connections, and then double-click
Local Area Connection, Local
Area Connection Status window
will appear, and then click
„Properties‟
Select „Use the following IP
address‟, then input the following
settings in respective field:
IP address: 192.168.0.x (where x is
an integer greater or less than 200, if
there‟s more than one computer
need to use this WPG on the same
network, each computer should use
an unique number)
Subnet Mask: 255.255.255.0
Click „OK‟ when finish.
2-3-2 Windows Vista IP address setup:
Loading...
+ 42 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.