Edimax Technology PS-1210MFn User Manual

Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any
form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of this Company .

This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Further, this company reserves the right to revise
this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.

The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about
this product, please refer to the User Manual on the CD-ROM. The software
and specifications are subject to change without notice. Please visit our web
site www.edimax.com for the update. All rights reserved including all brand
and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders .

Notice according to GNU/GPL-Version 2

This product includes software that is subject to the GNU/GPL-Version 2.
You find the text of the license on the product cd/dvd. The program is free
software and distributed without any warranty of the author. We offer, valid
for at least three years, to give you, for a charge no more than the costs of
physically performing source distribution, a complete machine-readable
copy of the corresponding source code.
Please contact Edimax at: Edimax Technology co., Ltd, NO. 3, Wu-Chuan
3rd RD Wu-Ku-Industrial Park, Taipei Hsien, Taiwan. R.O.C., TEL :
[phone], FAX : [phone], [e-mail]

Contents

1. Introduction ...................................................................... 1

2. Product Package ............................................................. 2

3. MFP Server with Print Server .......................................... 3

4. MFP Server Installation in Windows 2000/XP/Vista/7 ..... 5

4.1 Hardware Installation Procedure ........................... 5

4.2 Software Installation Procedure ............................ 6

4.2.1 EZMax Installation Wizard .................... ……7

4.2.2 MPF Server Utility Installation ..................... 8

4.3 MFP Server Utilities ............................................ 17

4.4 Install the MFP Drivers/Utilities ........................... 18

4.4.1 Never Install MFP Driver/Utilities ............... 19

4.4.2 MFP Drivers/Utilities has been installed .... 22

5. Using the MFP ............................................................... 24

5.1 Share Print .......................................................... 25

5.2 Share Scan ......................................................... 26

5.3 Share Card Reader ............................................. 27

5.4 Fax a File ............................................................ 28

6. MFP Manager ................................................................ 30

6.1 MFP Server List .................................................. 30

6.2 My Favorite ......................................................... 33

6.3 Auto Connect List ................................................ 35

6.4 Quick Setup ........................................................ 38

6.5 Option Settings ................................................... 40

6.5.1 General Setting .......................................... 40

6.5.2 Search for MFP Server .............................. 41

7. Server Configuration ...................................................... 42

7.1 Introduction ......................................................... 42

7.2 Search for All Available MFP Server ................... 43

7.3 Status of MFP Server .......................................... 44

7.4 Setup the MFP Server ........................................ 45

7.5 General Configuration ......................................... 46

7.6 TCP/IP Configuration .......................................... 47

7.7 System Configuration .......................................... 50

7.8 Wireless Configuration ........................................ 52

7.9 MFP Server Management ................................... 63

7.10 Report ................................................................. 64

8. Web Management ......................................................... 65

8.1 Introduction ......................................................... 65

8.2 Login ................................................................... 66

8.3 Device Setup ....................................................... 67

8.3.1 System ....................................................... 67

8.3.2 Printer ........................................................ 68

8.3.3 TCP/IP ....................................................... 69

8.4 Setup Wizard ...................................................... 70

8.4.1 System ....................................................... 70

8.4.2 Wireless ..................................................... 72

8.4.3 TCP/IP ....................................................... 79

8.4.4 Save Settings ............................................ 80

8.5 System Tools ....................................................... 81

8.5.1 Load Default .............................................. 81

8.5.2 Upgrade Firmware from Browser .............. 82

9. LPR Printing ................................................................... 83

10. RAW Printing ................................................................. 89

1 1. IPP Printing .................................................................... 95

11.1 Introduction ......................................................... 95

11.2 System Setup ...................................................... 95

11.2.1 MFP Server Side ....................................... 95

11.2.2 Client Side ................................................. 95

12. MFP Server Inst allation in Windows 98SE/Me/NT ...... 100

12.1 Software Installation Procedure ........................ 101

12.1.1 EZMax Installation Wizard ....................... 102

12.1.2 MPF Server Utility Installation ................. 103

12.2 Server Utilities ................................................... 112

12.3 Network Port Setup ........................................... 113

12.4 Add Printer ........................................................ 114

13. UNIX/Linux System Network ....................................... 118

13.1 GUI Mode .......................................................... 118

13.2 Console Mode ................................................... 123

13.2.1 Enable MFP Server’s TCP/IP Support .... 123

13.2.2 Setup MFP Server’s IP Address .............. 123

13.2.3 Verify MFP Server’s IP Address .............. 126

13.2.4 Configure Remote LPD Printing on the Host
……………………………………………….126

14. MFP Server Installation in MAC OS ............................. 128

14.1 MAC 10.4.x ....................................................... 128

14.2 MAC 10.3.x ....................................................... 129

15. Troubleshooting ........................................................... 133

1. Introduction

Thank you for purchasing and using our MFP server. This MFP
server allows your Multi-function, all-in-one printer (called for short:
MFP) or printer to become a shared device on the network. Unlike
many print servers, it can communicate with MFP and printer as if
it is connected directly to your computer. Because of the features,
all users can share print, scan, card reader and fax functions
through the network. Furthermore, the MFP Server can build the
bi-directional communication with MFPs and Printers so that it can
help to monitor important information such as ink levels and paper
levels.

The MFP server supports print, scan, card reader and fax sharing
functions in the most popular operating systems: Windows 2000
SP4 above, Windows XP SP1 above and Windows Vista. It also
supports Windows XP and Vista scanning utility and MFP vendors’
scanning utilities. When you want to scan in the Windows XP, Vista
or Windows 7, you can choose one of the utilities.

Not only be a MFP Server, this MFP Server can also be a
traditional print server. It supports TCP/IP network protocol and
LPR, RAW and IPP printing protocols. It can share print function in
the various common network operating systems including
Windows 2000/XP/2003/Vista/7, Unix, Linux and MAC OS 9.x
above.

The MFP server is the best solution for users to share MFP or
printer conveniently and easily. It offers the most flexibility and
manageability for MFP or printer on your Local Area Network at an
extremely low cost and with an absolute minimum setup and
maintenance required.

1

2. Product Package

This package contains the following components:

 One MFP Server
 One Antenna (PS-1206MFg, PS-1208MFg or PS-1210MFn)
 One Power Adapter
 One Quick Installation Guide
 One CD (EZmax Wizard / Utility, Multi-language Quick

Installation Guide & User Manual)

2

3. MFP Server with Print Server

This MFP Server supports dual functionalities: MFP Server Mode
and Print Server Mode at the same time. Users can choose one of
the modes to share MFP or Printer functions through the MFP
Server.

MFP Server Mode:

The MFP Server can communicate with MFP and printer as if it is
connected directly to your computer. This enables users to connect
to MFP for sharing print, scan, card reader and fax functions. If the
MFP Server is connected to a printer but not MFP, users still can
share printing function through the operation mode. The supported
OS in this mode is Windows 2000 SP4 above, Windows XP SP1
above, Vista and Windows 7. The MFP Server mode doesn’t
support Windows 98SE/ME/NT, Linux/Unix or MAC OS. For the
detailed applications, please refer to the following chapters.

Chapter 4: MFP Server Installation in Windows 2000/XP/Vista/7
Chapter 5: Using the MFP
Chapter 6: MFP Manager

3

Print Server Mode:

The MFP Server also supports LPR, IPP and RAW printing
protocols, which enable users to share print function from MFP or
Printer. The supported OS is Windows 2000/XP/2003/Vista/7,Unix,
Linux and MAC OS 9.x above. In Windows Vista/7, the MFP
Server only supports LPR printing protocol. For the detailed
applications, please refer to the following chapters.

Chapter 9: LPR Printing
Chapter 10: RAW Printing
Chapter 11: IPP Printing
Chapter 12: MFP Server Installation in Windows 98SE/ME/NT
Chapter 13: Unix System Network
Chapter 14: MFP Server Installation in MAC OS

4

4. MFP Server Installation in Windows
2000/XP/Vista/7

Before you start, you should have:
 One computer with Windows 2000 SP4 above, Windows XP

SP1 above or Windows Vista (32-bit/64-bit) / Windows 7.

 One MFP or printer with USB port and an installation CD
 One Category 5 Ethernet Cable
 One USB Cable

4.1 Hardware Installation Procedure

1. Unpack the MFP Server package and verify that all the items

listed in the previous section are provided.

2. Plug the USB cable to the MFP Server with the MFP or printer

that you want to share on the network.

3. Connect the MFP Server to your network by attached the

network cable to the network port of the MFP server.

4. Connect the power adapter to the MFP Server. The MFP Server

will perform the Power-On-Self-Test (POST) after it is powered
on. When the Status LED is unlighted, the MFP Server is ready.

Note:

1. You must use the power adapter shipped along with the

MFP Server, do NOT use any other power adapter from
other sources.

2. To prevent the compatibility problem between MFP Server

and a few MFP or printer, it is recommended that you power
on the MFP Server before the MFP or printer.

5

4.2 Software Installation Procedure

Before you start, you should check your computer’s operating
system. This program can be run in Windows 2000 SP4 above,
Windows XP SP1 above and Windows Vista. The following
procedures are running in Windows XP, for Windows 2000, Vista
and Windows 7, the procedures are similar.

Tip:

You have to uninstall all the MFP server drivers and utilities if you
have installed the previous version.

6

4.2.1 EZMax Installation Wizard

This wizard can be run in Windows 2000/XP/Vista/7. The
following procedures are operated in Windows XP.

You can install the MFP Server by EZMAX Setup Wizard in the
CD-ROM including in the package. The wizard is an easy and
quick configuration tool for internet connection with series process.
When you start EZMAX Setup Wizard, you will get the following
welcome screen. Please choose the language to start the
configuration. The wizard will guide you to finish your network
connection. We will not provide any instruction for the EZMAX
Setup Wizard here.

If you lose the CD ROM or you prefer the traditional setup
procedure, please follow the instruction as following step in
this quick installation guide.
** Default login user name & password:
User name: admin
Password: 1234

7

4.2.2 MPF Server Utility Installation

**Please find the utility manually from CD-ROM drive’s root
directory or download it from Edimax website. If you have any
question please check with Edimax local technical support team.

1. Please execute the MFP Server Utility installation software

manually.

2. The “MFP Server Utilities - InstallShield Wizard” is displayed,

please click "Next".

8

3. Click “Next” to install the MFP Server utilities in the default

folder or click “Change” to specify the destination folder where
you would like to install the MFP Server utilities.

4. The system starts installing the MFP Server Utilities.

9

5. The “MFP Server Configuration” screen is displayed. If you want

to configure the MFP Server, please click “”Next” directly. Or
you can select “No, I will configure the MFP Server later” and
click “Next” to complete the installation.

The following steps are for MFP Server Configuration.

10

6. The MFP Server List will auto search the MFP Servers in the

network. Select the MFP Server you want to setup and click
“Next” to continue.

7. Enter the “User Name” and “Password” of the MFP Server you

have selected to login the MFP Server. The default “User
Name” is “admin”; default “Password” is “1234.”

11

8. Set the “Alias Name” and the “MFP Server Description” to the

MFP Server here. Click on “Next”.

Note:

You can define the location or other information of the MFP Server
for easy to find the MFP by filling “MFP Server Description”.

12

9. Please set the network settings for the MFP Server manually.

By default, the network settings are as follows.

IP Address: 192.168.2.2
Subnet Mask: 255.255.255.0

If you have selected “DHCP”, the MFP Server will try to
determine your network settings automatically. If a DHCP
Server is present within the network, the MFP Server will
automatically obtain and configure the network settings
assigned by the DHCP Server. The assigned IP Address will be
shown in the IP Address fields. If no DHCP Server is present
within the network, please assign the network settings of the
MFP Server manually. Please click “Next” once you have found
appropriate network settings for the MFP Server.

Note:
The MFP Server IP Address should be in the same network
segment with the connected computer. If the network settings are
incorrect, a message will be prompted to remind you after you click
“Next”. Please make sure that you have set the right settings
before going to the next step. If you don’t want to set it now, please
click “Cancel” to finish the installation. You can then use the
“Server Manager” utility to configure the MFP Server.

13

10. The “Wireless Network Settings” screen will allow you to

connect your wireless MFP Server to your wireless router,
access point, or point-to-point ad-hoc connection.

The MFP Server will automatically scan the wireless
networks nearby. Please select the appropriate wireless
network that you would like to connect from the list and click
“Next”.

You may choose to scan for the wireless access point or
router (Infrastructure mode) or the wireless adapters (Ad
Hoc mode). Or, you can manually enter the wireless
network information (Manual mode). By default, the wireless
settings are as below.

Mode: Ad Hoc
SSID: Default
Channel: 11

14

11. If you chose to connect to an encrypted network, the

“Wireless Security Settings” screen will be appeared. You
have to select the “Security Mode” and enter the key the
same as the settings on your wireless devices. For more
information about the security settings, please refer to the
Section 7.8.

12. The configurations are finished. Please click “Finish” to apply

new settings.

15

13. Click “Finish” to complete the installation.

Note:
If the Windows XP Firewall in your system has been enabled, the
MFP Server will automatically open ports for the MFP Server
programs smoothly run in your system. It will not cause abnormal
behaviors or unsafe on your system.

14. Choose if you want to run the “MFP Manager” utility

automatically when Windows starts. It is recommended to
enable the setting.

16

15. The default wireless setting is “Auto” mode. The MFP Server

will detect if the MFP Server is connected to a wired LAN
network through the attached Ethernet cable. If yes, it will
work in wired network. To enable the wireless setting,
please remove the Ethernet cable. For more detailed
information about wireless setting, please refer to Section

7.8.

4.3 MFP Server Utilities

After the installation is completed, there will be three utilities and a
text file in the MFP Server’s Program folder.

MFP Manager – Allows you to manage the connection between
the MFP and your computer for sharing MFP function.

Server Configuration – Allows you to configure the MFP Server’s
IP Address, network protocols and other advanced features. It also
allows you to manage the MFP Server.

Uninstall – Assistant for removing all installed MFP Server
software programs.

About Version – Display the version of each utility including in the
MFP Server software programs.

17

4.4 Install the MFP Drivers/Utilities

When the installation is completed, the “MFP Manager” will be
popped up. It will automatically find the MFP Servers and the
connected MFPs in the network and show it in the “MFP Server
List”.

Before you start to install the MFP selected from the “MFP Server
List”, please check your computer’s MFP installation status.

 You never install the MFP drivers/utilities; please refer to the

Section 4.4.1.

 You have installed the MFP drivers/utilities; please refer to the

Section 4.4.2.

18

4.4.1 Never Install MFP Driver/Utilities

Before the installation, please read the manual of the MFP. Some
MFP requires users to install the drivers/utilities before connecting
the MFP to your computer. Some MFP requires connecting the
MFP to your computer during the installation. Please refer to the
below illustration of “HP ALL-In-One Series” which is the screen
displayed during the installation.

To connect the MFP to your computer through the MFP Server just
like you have directly connected the MFP to your computer through
the USB cable, you can follow the steps below.

19

1. Select the MFP that you want to install in the “MFP Server List”

and click “Connect” button.

2. The Windows will detect the new hardware and prompt to install

the MFP drivers. When the system stops prompting, the drivers
are all installed. If the system can’t find the MFP driver, please
insert the installation CD of the MFP and designated to find
drivers in the CD.

Note:

If the MFP you have connected is a composite device, the system
will install the driver for composite device at first. The following
screen will be popped up, please click “Continue Anyway”. When
the system stops prompting, the drivers are all installed. If the
system can’t find the MFP driver, please insert the installation CD
of the MFP and designated to find drivers in the CD.

20

3. After you have completed the MFP installation, you will see the

MFP is added to the “Printers and Faxes” in Windows.

21

4.4.2 MFP Drivers/Utilities has been installed

To bundle the MFP drivers/utilities that you have installed to the
MFP Server, please follow the steps below.

1. Select the MFP that you want to install in the “MFP Server List”

and click “Connect” button.

2. The Windows will detect the new hardware and prompt to install

the MFP drivers. When the system stops prompting, the drivers
are all installed. If the system can’t find the MFP driver, please
insert the installation CD of the MFP and designated to find
drivers in the CD.

Note:

If the MFP you have connected is a composite device, the system
will install the driver for composite device at first. The following
screen will be popped up, please click “Continue Anyway”. When
the system stops prompting, the drivers are all installed. If the
system can’t find the MFP driver, please insert the installation CD
of the MFP and designated to find drivers in the CD.

22

3. After the installation, a copy of the MFP will be added to the

“Printers and Faxes” in Windows.

Tip :

The new copy of the MFP is bundled to the MFP Server. Please
use the MFP to share print, scan, card reader or fax functions
through the network.

23

5. Using the MFP

After you have followed the install wizard to finish the MFP
installation, the MFP is now connected to your computer. You can
start sharing print, scan, card reader or fax function provided by
the MFP.

Tip 1:

If you have finished using the MFP, please click “Disconnect” to
release the MFP. Another users can’t use the MFP until the MFP is
released

Tip 2:

It is recommended to enable “Auto Release” setting. The MFP
Server will auto release your connection to the MFP after a period
of idle time that you have assigned. So the MFP will not be
occupied too long and other users can share the MFP frequently.
Please refer to Section 6.1 for more information.

24

5.1 Share Print

The MFP will be added to “Printers and Faxes” in the Windows
after the MFP is installed. When you have connected to the MFP
by clicking “Connect” in the “MFP Manager”, the MFP Server will
auto create the connection between the MFP and your computer
and then you can print a document just follows the same steps as
usual.

Tip:

If you have sent a printing job to the MFP while the MFP is
connecting by a user, you may be prompted that the device is not
found or the document is failed to print. Please resend the printing
job after the MFP is idle or not being connected.

25

5.2 Share Scan

Most of the MFP provides scan utility for users. You can scan
pictures or documents through the utility. In Windows XP and
Windows Vista, user can also scan from Windows XP and
Windows Vista scanning utility.

An example: HP 1600 Series Utilities

Windows XP Scanning Utility

26

5.3 Share Card Reader

If the MFP supports card reader function, you can read the files
from the plugged card reader through the MFP Server.

27

5.4 Fax a File

If the MFP supports fax function, you can fax files from your
computer to the fax number you designated.

An example: Fax through HP Officejet 5600 Series

After the MFP is installed, there is a fax device will be added to
“Printers and Faxes” in the Windows. When you have connected to
the MFP by clicking “Connect” in the “MFP Manager”, you can fax
a file through the MFP Server to the fax device.

Procedures to fax a file

1. In the Microsoft Office or other programs, select “Print” from the

“File” menu.

2. The following screen will be popped up, select the fax device

and then click “Print”.

28

3. The “Send Fax” screen is popped up, please configure the file

and enter the fax number. Click “Send Fax” to fax the file.

29

6. MFP Manager

6.1 MFP Server List

The “MFP Manager” can automatically find the MFP server in the
network and show it in the MFP Server List. Users can select a
MFP and click “Connect” to connect the MFP just like you have
directly connected the MFP to your computer through USB cable. It
also displays the information of the connection status.

When you don’t want to use the MFP or Printer, please click
“Disconnect” so that other users can use the device. Or you can
enable the “Auto Release” setting, so that the MFP Server will
release your connection after a period of idle time that you have
assigned.

If you unplug the USB cable or turn off the MFP while using, the
device will not display in the list. After you reconnect the USB cable
or turn on MFP, you have to click “Refresh” and “Connect” buttons
in the “MFP Manager” to recover the connection.

30

MFP Server List

MFP Server List The “MFP Server List” will list all the MFP

Servers within the network. You can find the
information of the MFP Servers including “MFP
Server Name”, “MAC ID”, “IP Address” and the
device that is connected to the MFP Server.

MFP Server/MFP
Information

When you are clicking on the “MFP Server” in
the “MFP Server List”, you will see the “MFP
Server Description” and the “Idle Timeout”
setting for the MFP Server.
MFP Server Description – It is a description
that can help users to identify where or what the
MFP Server is.

Idle Timeout – From here, each user can know
his/her auto release setting. To avoid occupying
the MFP overtime, each user can enable the
“Auto Release” setting at the bottom of the “MFP
Manager” utility. It is used to automatically
disconnect the connection after the MFP is idle
for a specified period of time. By default, it is
never released.

When you are clicking on the “MFP” in the “MFP
Server List”, you will see the information
including “Status”, “Computer Name” and
“Contact Information”.

Status – It displays the status of the MFP
including Connected, Idle and Busy. When the
status is “Connected”, it indicates that you are
connecting the MFP. When the status is “Idle”, it

31

indicates that the MFP is not being used. When
the status is “Busy”, it indicates that other user is
using the MFP to scan, print, or etc.

Computer Name – It display the computer name
of the user who is connecting to the MFP.
Contact Information – When the current user
has set his “Contact Information”, you can see it
here. You can contact with the current user for
asking to disconnect the MFP.

Refresh Refresh the “MFP Server List” immediately.

Connect Let the MFP be connected to your computer.

Disconnect Disconnect the selected MFP.

Add to My
Favorite

Add the MFP Servers that you frequently use to
“My Favorite List”.

Auto Release
when idle time is
over xx minutes
(5-255)

To avoid you occupy the MFP overtime; you can
setup auto release function. It is used to
automatically disconnect the current connection
after the MFP is idle for a specified period of
time. By default, it is never released. It is
recommended to enable the setting after the
MFP and MFP Server are installed completely so
that the MFP resource will not be occupied
permanently.

32

6.2 My Favorite

You can add the frequently use MFP Servers to “My Favorite” list.
The MFP Server in the list will be added to the quick link list when
you right click the MFP Server icon in the system tray. Please refer
to Section 6.4 to know more about the quick setup functions.

My Favorite List

My Favorite List The “My Favorite List” will list your favorite MFP

Servers. You can find the information of the MFP
Servers including “MFP Server Name”, “MAC
ID”, “IP Address” and the device that is
connected to the MFP Server.

MFP Server/MFP
Information

The information listed here are the same as MFP
Server List. Please refer to Section 6.1.

Refresh Refresh the “MFP Server List” immediately.

Connect Let the MFP be connected to your computer.

33

My Favorite List

Disconnect Disconnect the selected MFP.

Delete Delete the selected MFP Server from the “My

Favorite List”.

Auto Release
when idle time is
over xx minutes
(5-255)

To avoid you occupy the MFP overtime; you can
setup auto release function. It is used to
automatically disconnect the current connection
after the MFP is idle for a specified period of
time. By default, it is never released. It is
recommended to enable the setting after the
MFP and MFP Server are installed completely so
that the MFP resource will not be occupied
permanently.

34

6.3 Auto Connect List

To let the system occupy the MFP server automatically when you
want to print a document just like the behavior of using traditional
print server, you can add the MFP into your Auto Connect List. The
system will send the printing jobs to the MFP when the MFP
Server is idle and not being connected.

Tip:

If you have sent a printing job to the MFP while the MFP is
connecting by a user, you may be prompted that the device is not
found or the document is failed to print. It also happens in some
MFPs or printers even though the MFP is not connecting by a user.
Please follow the message to retry and the MFP will queue your
printing job in your computer spooler. The MFP Server will then
print the job after the MFP is idle or disconnected.

To add the MFP to the Auto Connect List, please follow the steps
below.

1. Click “Add” from the “Auto Connect List”.

35

2. The MFP Servers within the network will be displayed in the

following screen. Select the MFP Server you would like to add
to the list.

3. Select the MFP that is connected to the selected MFP Server.

Click “Ok”. Note that in some cases, new coming printing jobs
cannot be printed because the MFP is already disconnected. It
will cause unformatted messages to be printed out. “Keep
connecting for 30 second(s) after printing has been finished
(5-60)” is enabled by default. It will help to avoid this kind of
situation.

36

4. The setup is finished.

37

6.4 Quick Setup

Right click on the MFP Server icon in the system tray you can see
the MFP servers you have designated to “My Favorite List”. You
can directly connect or disconnect the MFP and check the MFP
information from the here easily.

38

Quick Setup

Status The current status of the MFP will be displayed

here. “Connected” indicates that you are
connecting to the MFP. “Busy” indicates the
MFP is being used. “Idle” indicates that the MFP
is free to use by any users.

Connect If the MFP is free to use, the “Connect” will be

available to click for occupying the MFP. Or it will
be grayed.

Quick Setup

Disconnect Disconnect the selected MFP. The “Disconnect”

will be available only for the current user.

Information To check more information about the MFP

Server and the MFP, please click this button.
The information will be listed as the illustration
above.

39

6.5 Option Settings

6.5.1 General Setting

General Setting

Run MFP Manager
when Windows starts

Minimized when start
MFP Manager

Refresh status every
xx seconds. (5~300)

Your Contract
Information

Execute the “MFP Manager” when Windows
starts every time. By default, it is enabled.

Minimized the “MFP Manager” to an icon in
the system tray when you start the “MFP
Manager”. By default, it is disabled.

Setup the refresh interval for device status
update. By default, it is disabled.

Enter your contact information here. When
you connect to the MFP, your contact
information will be displayed in the right side
of the program for other users to contact
you.

40

6.5.2 Search for MFP Server

If there is an MFP Server is not in the network as your computer,
you can enter the IP Address of the MFP Server to do the remote
search. The MFP Server in the “Remote MFP Server List” will be
added to the “MFP Server List” for you to configure.

Note:

If the remote MFP Server you have searched is behind NAT Router,
the MFP Server may not operate normally.

41

7. Server Configuration

7.1 Introduction

This chapter introduces MFP Server’s system configuration utility
in Windows environment. This utility provides the most complete
management and configuration functions on the MFP Server side.
This utility only provides configuration functions for MFP Server
itself; it does not include configuration functions for client side or
other file server in the network environment.

The Configuration Utility provides the following configuration and
management functions:

 Search MFP Server: Search All Available MFP Servers on the
Network.

 Status: Display MFP Server Network Status.
 General Configuration: Configure general settings about the

MFP Server such as Server Name, Password, etc.

 TCP/IP Configuration: IP Address and DHCP Server
Configuration.

 System Configuration: MFP Server Network Ability Setting

and Firmware Upgrade.

 Wireless Configuration: Search for the available wireless

networks and configure the wireless settings of the MFP Server
for the wireless connection.

 MFP Server Management: For administrator to manage the

MFP Server. Administrator can force disconnect the current
connection of the MFP Server.

 Report: List the some information of All Available MFP Servers

on the Network.

42

We will explain each function separately in the following section.

7.2 Search for All Available MFP Server

Every time when you run the “Server Manager” configuration utility,
click the “Search” icon

on the tool bar. The configuration
utility will delay for several seconds because the utility is using
system’s available network protocols to search for all MFP Servers
on the network. All available MFP Servers will be listed under
“Server Group” on the left side of the window.

You must select the MFP Server you would like to configure from
the list. The system will, at the same time, display the selected
MFP Server’s status on the right side of the window.

43

7.3 Status of MFP Server

Click “Status” icon on the tool bar, the status of the currently
selected MFP Server will be showed on the right side of the
window. The information of the MFP Server displayed are including
MAC ID, Model Type, Firmware Version, status of each server port,
IP address, subnet mask, default gateway and supported printing
protocols…etc.

You can refresh the MFP Server’s status by pressing the “Refresh”
button

.

You can restart the MFP Server by pressing the “Reboot” button

.

44

7.4 Setup the MFP Server

Click “Setup” icon on the tool bar, the setup items of the
current selected MFP Server will be showed on the right side of the
window.

Double click one of the icons to set up the selected MFP Server. A
screen will pop up to verify “User Name” and “Password” of the
MFP Server. The default values are: User Name: admin,
Password: 1234.

Tip:

When you have finished the settings, please click “

” to restart

the MFP Server to let the settings take effect.

45

7.5 General Configuration

Double Click “General” icon and the General configuration window
will pop-up.
You can see basic MFP Server information in this page. You also
can configure the “Server Name”, “User Name” and “Password”
here.

Server Name, the name of the MFP Server. You can use this
name to identify the MFP Server when you are searching for the
MFP Server by the “Server Manger” utility.

User Name / Password is used to authenticate the administrator
to login the MFP Server for configuring it from the “Server Manger”
utility or the Web Management tool.

46

7.6 TCP/IP Configuration

Double Click “TCP/IP” icon and the TCP/IP configuration window
will pop-up.

47

You can configure the MFP Server to automatically get IP from
DHCP server or manually specify static IP. The MFP Server also
has a built-in DHCP server. You can enable this DHCP server and
let it manages IP for you.

IP Address Assignment:

Click the “IP” button to enter the IP setting page. If you need the
MFP Server to automatically get an IP from DHCP server, select
“Auto IP”. You also can select “Static IP” to manually assign “IP
Address”, “Subnet Mask” and “Gateway” for the MFP Server. By
default, “Static IP” is enabled and the default settings are as
follows.

IP Address: 192.168.2.2
Subnet Mask: 255.255.255.0

Auto IP – The IP Address information of the MFP Server obtained

from DHCP Server will be displayed in the address field. If no
DHCP Server is present, you have to assign the information
manually.

Static IP – Manually assign the IP address information in the same
network with your computer to the MFP Server.

DHCP Server:

Click the “DHCP Server” button to enter into the DHCP server’s
setting page. By the default, the DHCP server is disabled.

Auto – If “Auto” is selected, the MFP Server will detect DHCP
server within the network automatically and once the DHCP server
doesn’t exist, the MFP Server will turn on his own DHCP server
and assign IP Address to client. Please fill in the “Starting Address”,
“Range”, “Subnet Mask”, “Gateway” and “DNS”; then the MFP
Server will assign a unique IP within the range for each DHCP
client.

48

Enable – If the DHCP is enabled, you have to assign a range of IP
addresses. Fill in the “Starting Address”, “Range”, “Subnet Mask”,
“Gateway” and “DNS”; then the MFP Server will assign a unique IP
within the range for each DHCP client.

Disable – The DHCP Server is disabled. You have to build up a
DHCP Server in the network or set the IP Address for each client
manually.

49

7.7 System Configuration

Double Click “System” icon and the System configuration window
will pop-up.
In the System configuration page, you can see all available printing
protocols and upgrade the new firmware for this MFP Server.

Upgrade Firmware: You can use this “Upgrade Firmware” tool to
update the newest firmware of the MFP Server. Click “

” button
and select the correct firmware in your PC. After selecting the
firmware file, click the “Upgrade” button to finish the firmware
update process.

Tip:

Before you upgrade the firmware, please make sure that the IP
Address settings of the MFP Server are in the same network as
your computer.

Load Default: If you want to reset the MFP Server to default
factory settings, please click “Load Default”.

50

Wireless Function: You can select “Auto”, Enable” or “Disable” to
manually configure the wireless function.

Auto – “Auto” is the default setting of the MFP Server. At this mode,
the MFP Server will automatically decide to enable or disable the
wireless function. When the MFP Server starts up, it will
auto-detect if the LAN port is connected to an active network by an
Ethernet cable. If this is the case, the MFP Server will run in
Ethernet mode. If the MFP Server is not connected to an active
network by Ethernet cable, the MFP Server will run in wireless LAN
mode.

Users can plug the Ethernet cable to the MFP Server at the first,
after configuring the MFP Server features and wireless settings;
they can unplug the Ethernet cable to enable the wireless
connection. It makes the configuration much easier without
creating the wireless connection in advance.

Note:
After you have set the wireless function, please remove the
Ethernet cable and then re-plug the power jack of the MFP
Server to activate the wireless connection.

Enable – Enable wireless function only, the MFP Server’s wireless
LAN will be always enabled and Ethernet will be always disabled.

Disable – Disable the wireless function, the MFP Server’s wireless
LAN will be always disabled and Ethernet will be always enabled.

Domain Country: The wireless channels are different from country
to country. Generally, the channels are from 1 to 11 in USA and
from 1 to 13 in Europe. The operating channel will be set to the
MFP Server before importing. If you are in different country, please
make sure that you have set the available channels according to
your location.

51

7.8 Wireless Configuration

If you want to use the MFP Server through wireless LAN, please
set up the MFP Server through Ethernet first and make sure your
wireless LAN setting is correct. After setting the wireless LAN,
unplug the Ethernet cable and restart the MFP Server, then you
can start to use the MFP Server through wireless LAN. If the
wireless configuration does not work, please plug the Ethernet
cable again, restart the MFP Server and configure the MFP Server
through Ethernet until the wireless LAN settings are correct.

The default settings of the MFP Server wireless function are as
follows.

y Mode: Ad Hoc
y SSID: Default
y Channel: 11

52

Double Click “Wireless” icon and the wireless configuration window
will pop-up. If you use access point to build up wireless network,
you have to select “Infrastructure Mode”. If you do not have any
access point and want to use peer-to-peer connection to build up
wireless network, you have to select “Ad-Hoc Mode”.
For Wireless Function, you can select “Auto”, Enable” or “Disable”
to manually configure the wireless function.

Auto – “Auto” is the default setting of the MFP Server. At this mode,
the MFP Server will automatically decide to enable or disable the
wireless function. When the MFP Server starts up, it will
auto-detect if the LAN port is connected to an active network by an
Ethernet cable. If this is the case, the MFP Server will run in
Ethernet mode. If the MFP Server is not connected to an active
network by Ethernet cable, the MFP Server will run in wireless LAN
mode.

Users can plug the Ethernet cable to the MFP Server at the first,
after configuring the MFP Server features and wireless settings;
they can unplug the Ethernet cable to enable the wireless
connection. It makes the configuration much easier without
creating the wireless connection in advance.

Note:
After you have set the wireless function, please remove the
Ethernet cable and then re-plug the power jack of the MFP
Server to activate the wireless connection.

Enable – Enable wireless function only, the MFP Server’s wireless
LAN will be always enabled and Ethernet will be always disabled.

Disable – Disable the wireless function, the MFP Server’s wireless
LAN will be always disabled and Ethernet will be always enabled.

53

After selecting the operation modes of the wireless function, click
“Next” to go to further detailed configuration.

Infrastructure Mode:

In the Infrastructure mode, you have to let the MFP Server
associate with an access point. You let the MFP Server scan for an
available access point automatically or manually assign the SSID
of the access point you want to use.

If you select to let the MFP Server scan for an available access
point, the following window will pop up.

54

The table will list the available access points near the MFP Server.
Select an access point in the list and click “Next”. If you cannot find
the access point that you want to use, click “Scan” to let the MFP
Server scan again.

Ad Hoc Mode:

55

In the Ad-Hoc mode, you can let the MFP Server automatically
associate with other wireless station or manually assign the SSID
of your wireless network. You can let the MFP Server automatically
select the channel that is the same with the wireless station that
you want to connect or manually assign a channel.

If you select to let the MFP Server scan for an active wireless
station, the following window will pop up.

The list is the scanned active wireless stations. Select a wireless
station in the list and click “Next”. If you cannot find the wireless
station that you want the MFP Server to communicate with, click
“Scan” to let the MFP Server scan again.

56

Both “Infrastructure” and “Ad-Hoc” mode have to go through the
following procedure:

57

This MFP Server supports WEP and WPA-PSK security mode. If
you want to use WEP encryption to protect your wireless network,
you have to select “WEP(ASCII)” or “WEP(HEX)”. If you want to
use WPA-PSK, you have to select “WPA-shared key” or
“WPA-None” specified for Ad Hoc mode. The wireless security
setting should be the same with other wireless devices in the same
network.

WEP Security Mode:

58

You can select “64 bit” or “128 bit” length and “Hexadecimal” or
“ASCII” format for the encryption key. Longer key length can
provide stronger security but worth communication performance.

PassPhrase – A “PassPhrase” simplifies the WEP encryption
process by automatically generating the WEP encryption keys for
the MFP Server. This setting is only valid when the security mode
is in “WEP(HEX)”.

Key 1 to Key 4 – Enter four key values by following the rules
below and select one key as the default key.

If the key length is 64-bit, enter 10-digit Hex values or 5-digit ASCII
values as the encryption keys. For example: “0123456aef“ or
“Guest“.

If the key length is 128-bit, enter 26-digit Hex values or 13-digit
ASCII values as the encryption keys. For example:
“01234567890123456789abcdef“ or “administrator“.

59

WPA-shared key or WPA-None Security Mode:

“WPA-shared key” (for an infrastructure network) or “WPA-None”
(enables WPA security for your ad hoc network) requires users to
select the advanced encryption methods, i.e. TKIP or AES and
enter a set of shared key.

60

TKIP – TKIP (Temporal Key Integrity Protocol) changes the
temporal key every 10,000 packets. This insures much greater
security than the standard WEP security.

AES – AES has been developed to ensure the highest degree of
security and authenticity for digital information and it is the most
advanced solution defined by IEEE 802.11i for the security in the
wireless network.

Key – Enter 8 to 63 digits of ASCII format to be the key for the
authentication within the network.

When you finish configuring the wireless security, click “Next” to go
to next step.

You can select to let the MFP Server automatically obtain IP
settings with DHCP client or manually assign the IP settings.

If you manually assign the IP settings, you have to enter IP
address, subnet mask and default gateway address.

61

When you finish configuring the IP settings, click “Next” to confirm
the IP Address configuration.

Click “Save” to save the wireless configuration.

62

7.9 MFP Server Management

Double Click “MFP Server Management” icon and the MFP Server
configuration window will pop-up. You are able to manage the MFP
Server as below.

Force Release: Select the port number and then click “Force
Release” will help to you disconnect the current connection
between the user and the connected device. It is very useful when
a user forgets to disconnect the MFP, administrator can force to
disconnect the connection and let the MFP be free to use.

MFP Server Description: Enter 15 digits description of the MFP
Server such as location or other information to help user to find the
MFP Server easily.

63

7.10 Report

Click “Report” icon on the tool bar, the Report window will
pop up.
The report lists basic information of all available MFP Servers on
the network. The information includes Device Name, MAC ID,
Model Type and Firmware Version of MFP Server.

64

8. Web Management

8.1 Introduction

MFP Server can be configured and managed on the Web. Through
Local Area Network, or even Internet, administrator can easily
configure and manage MFP Server’s various main functions in
browsers. Simply enter MFP Server’s IP address into your
browser’s address field to manage a MFP Server by MFP Server’s
built-in Web Server.

The default IP Address, User Name and Password settings of the
MFP Server are as follows.

IP Address: 192.168.2.2
User Name: Admin
Password: 1234

65

8.2 Login

You may use any Web Browser to review the status or configure
the settings of the MFP Server. After entering the IP address of the
MFP Server, a login page display. You have to enter correct “User
Name” and “Password” before going to the Web Management
pages.

Note: Default User Name is “admin”, default password is “1234”.

66

8.3 Device Setup

8.3.1 System

System Information includes “Device Name”, “MFP Server Name”,
“Model Type”, “Firmware Version”, “MAC Address”, “Wireless
Configuration”, and the protocols enabled status, etc.

67

8.3.2 Printer

This page lists information and the status of MFP or printer
connected to the MFP Server port. The status of the MFP or printer
includes “Connected”, ”Ready”, “Off Line” or “Paper Out”.

Connected: a user clicks “Connect” button in the “MFP Manager”
utility, and the connection between the user’s computer and the
MFP is built.

Ready: the MFP or printer is not connected by a user and is ready
to use.

Off Line: the MFP or printer is not connected by a user and is not
connected to MFP Server through USB cable or it is turned off.

Paper Out: the MFP or printer not connected by a user and is
paper out.

68

8.3.3 TCP/IP

This page lists all TCP/IP settings of the MFP Server including “IP
Address”, “Subnet Mask” and “Gateway”. It also can tell the DHCP
server is “On” or “Off”.

69

8.4 Setup Wizard

Note:

You can configure the MFP Server from the Setup Wizard. To let
the changes take effect, you have to click “Save Settings” in the
menu of the left side to reboot the MFP Server.

8.4.1 System

You can change the MFP Server name and password of the MFP
Server from here.

MFP Server Name, the name of the MFP Server. You can use this
name to identify the MFP Server when you are searching for the
MFP Server by the “Server Manager” utilities.

70

Password, enter the password you want to change to the MFP
Server. The password can be up to 7-digit alphanumeric format.
The default password is “1234”.

Re-type Password, enter the same password for the MFP Server
again.

8.4.1.1 Advanced Settings

Some advanced feature of the MFP Server can be set here.

TCP/IP Printing (LPR/IPP/RAW): This MFP Server supports
TCP/IP network protocol and LPR/IPP/RAW printing protocols. By
default these protocols are enabled.

71

8.4.2 Wireless

If you want to use the MFP Server through wireless LAN, please
set up the MFP Server through Ethernet first and make sure your
wireless LAN setting is correct. After setting the wireless LAN,
unplug the Ethernet cable and restart the MFP Server, then you
can start to use the MFP Server through wireless LAN. If the
wireless configuration does not work, please plug the Ethernet
cable again, restart the MFP Server and configure the MFP Server
through Ethernet until the wireless LAN settings are correct.

You can enable/disable the wireless function and set up the
wireless parameters for the MFP Server from here. The
parameters include “Function”, “Mode”, “ESSID” and “Channel
Number”. You can manually set the wireless network that you want
to connect in this page or use the “Site Survey” function to
automatically search for an available wireless network and
associate with it.

72

Function is for user to disable, enable or let the MFP Server auto
select to connect to the wired or wireless network. If “Disable” is
selected, the MFP Server can only connect to the network through
wired Ethernet. If “Enable” is selected, the MFP Server can only
connect to the network through Wireless LAN. If “Auto” is selected,
the MFP Server can automatically decide to enable or disable the
wireless function. The MFP Server only can work in either Ethernet
or wireless LAN mode. It cannot work in both Ethernet and
wireless LAN mode at the same time. When the MFP Server starts
up, it will auto-detect if the LAN port is connected to an active
network by an Ethernet cable. If the MFP Server is connected to
an active network by Ethernet cable when starting up, the MFP
Server will run in Ethernet mode. If the MFP Server is not
connected to an active network by Ethernet cable when starting up,
the MFP Server will run in wireless LAN mode. The MFP Server
default is in “Auto” mode.

Mode is the operation mode of wireless station. You can choose
either “Ad Hoc” or “Infrastructure” mode. If you do not have any
access point and want to use peer-to-peer connection, you have to
choose “Ad Hoc” mode. If you have an access point as the
wireless LAN infrastructure, you have to choose “Infrastructure”
mode.

ESSID is the unique name identified by in a wireless LAN. The ID
prevents the unintentional merging of two co-located WLANs.
Please make sure that the ESSID of all stations and access points
in the same WLAN network are the same.

Channel Number is the channel number of your wireless LAN.
Please make sure that the channel number of all stations and
access points in the same WLAN network are the same.

73

8.4.2.1 Site Survey

You can use this “Site Survey” function to search for available
access points in you location. In the list is the information of all
available access points or wireless stations, includes SSID, BSSID,
Channel, Type, Encryption and Signal Strength. You can select one
wireless device in the list for this MFP Server to associate with or
you have to go back to Wireless page to manually setup the
wireless parameters.

There is “WLAN Function” setting for you to setup
Auto/Disable/Enable wireless function of the MFP Server here.
Please refer to section 8.4.2 to know more about the setting.

74

8.4.2.2 Encryption

This MFP Server supports WEP and WPA-PSK security mode. If
you want to use WEP encryption to protect your wireless network,
you have to select “WEP”. If you want to use WPA-PSK, you have
to select “WPA-PSK” (for an infrastructure network or “WPA-None”
(enables WPA security for an ad hoc network). The wireless
security setting should be the same with other wireless devices in
the same network.

WEP Security Mode:

Key Length – You can choose “64-bit” to use WEP with 64-bit key

length encryption or choose “128-bit” to use WEP with 128-bit key
length encryption. The longer key length can provide better
security but worse transmission throughput.

75

Key Format – You may select to use ASCII Characters
(alphanumeric format) or Hexadecimal digits (in the "A-F", "a-f" and
"0-9" range) to be the WEP Key.
PassPhrase – A “PassPhrase” simplifies the WEP encryption
process by automatically generating the WEP encryption keys for
the MFP Server.

Default Key – Select one of the four keys to encrypt your data.
Only the key you select it in the “Default key” will take effect.

Key 1 – Key 4 – The WEP keys are used to encrypt data
transmitted within the wireless network. Fill the text box by
following the rules below.

64-bit WEP: input 10-digit Hex values (in the "A-F", "a-f" and "0-9"
range) or 5-digit ASCII character as the encryption keys. For
example: “0123456aef“ or “Guest“.

128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9"
range) or 10-digit ASCII characters as the encryption keys. For
example: “01234567890123456789abcdef“ or “administrator“.

76

WPA-PSK or WPA-None Security Mode:

77

“WPA-shared key” (for an infrastructure network) or “WPA-None”
(enables WPA security for your ad hoc network) requires users to
select the advanced encryption methods, i.e. TKIP or AES and
enter a set of shared key.

TKIP – TKIP (Temporal Key Integrity Protocol) changes the
temporal key every 10,000 packets. This insures much greater
security than the standard WEP security.

AES – AES has been developed to ensure the highest degree of
security and authenticity for digital information and it is the most
advanced solution defined by IEEE 802.11i for the security in the
wireless network.

Key – Enter 8 to 63 digits of ASCII format to be the key for the
authentication within the network.

When you finish configuring the wireless security, click “Save &
Next” to confirm the configuration.

78

8.4.3 TCP/IP

You can configure the MFP Server to automatically get IP from
DHCP server or manually specify static IP.

If you need the MFP Server to automatically get an IP from DHCP
server, select “Enable Obtain TCP/IP Settings Automatically (Use
DHCP/ BOOTP)”. You also can select “Disable Use the following
TCP/IP Settings” to manually assign “IP Address”, “Subnet Mask”
and “Gateway” for the MFP Server.

79

8.4.4 Save Settings

After configuring the MFP Server, you have to click the “Save
Settings” to save the settings and restart the system.

80

8.5 System Tools

8.5.1 Load Default

You can use this page to restore the factory default settings. All of
your previous setup will be cleared.

81

8.5.2 Upgrade Firmware from Browser

You can upgrade new firmware for this MFP Server in this page.
Click “Browse” to select the new firmware in your storage and then
click “OK”, the firmware will be updated in several minutes.

Be aware that if you have started upgrading firmware, you have to
follow all the upgrading steps or the MFP Server can’t turn back to
normal configuration.

82

9. LPR Printing

LPR Printing (Line Printer Remote technology) allows users to
connect to MFPs or printers via TCP/IP for printing sharing. The
computer with Windows 98SE/Me/NT/2000/XP/2003/Vista
operating system can use the protocol to share printing in the
network. MFP Server can support LPR printing by default.

If you install the MFP Server in Windows 98SE/Me/NT, the MFP
Server provides a tool “Network Port Setup” that helps to add the
LPR protocol to users’ computer easily. Please refer to Chapter 10.

To configure the LPR setting in Windows 2000/XP/2003/Vista,
please follow the steps below. Note that the following procedures
are running in Windows XP, for Windows 2000/2003/Vista, the
procedures are similar.

1. Click “Start”, choose “Settings” and select “Printers and Faxes”.

2. Click “Add a Printer”.

3. The “Add Printer Wizard” is displayed. Click “Next”.

83

4. Select “Local Printer attached to this computer” and click “Next”.

5. Choose “Create a new port” and “Standard TCP/IP Port”. Click

“Next”.

84

6. Please make sure that the MFP Server and the MFP or Printer

have turned on and connected to the network correctly before
you continue. Click “Next”.

7. Enter the IP Address of the MFP Server in the “Printer Name or

IP Address”. Click “Next”.

85

8. Select “Custom” and click “Settings”. When you have finished

the settings at step 9, click “Next” to continue.

9. Select “LPR” and enter “lpt1” in the “Queue Name”, click “OK”.

By default the queue name of the MFP Server is “lpt1”.

86

10. Click “Finish”.

11. Select a suitable printer manufacturer and the printer model

and click “Next”. If your printer is not in the list, click “Have
Disk…” to install the driver of the printer. After installation, the
printer model will be added to the list.

87

12. Choose to set the print whether as a default printer or not.

Click “Next”.

13. You have added the network printer to the PC successfully.

The information of the printer is displayed in the windows.
Click “Finish”.

88

10. RAW Printing

RAW Printing allows users to connect to MFPs or printers via
TCP/IP for printing sharing. The computer with Windows
2000/XP/2003 operating system can use the protocol to share
printing in the network. MFP Server can support RAW printing by
default.

To configure the RAW setting in Windows 2000/XP/2003, please
follow the steps below. Note that the following procedures are
running in Windows XP, for Windows 2000/2003, the procedures
are similar.

1. Click “Start”, choose “Settings” and select “Printers and Faxes”.

2. Click “Add a Printer”.

3. The “Add Printer Wizard” is displayed. Click “Next”.

89

4. Select “Local Printer attached to this computer” and click “Next”.

5. Choose “Create a new port” and “Standard TCP/IP Port”. Click

“Next”.

90

6. Please make sure that the MFP Server and the MFP or Printer

have turned on and connected to the network correctly before
you continue. Click “Next”.

7. Enter the IP Address of the MFP Server in the “Printer Name or

IP Address”. Click “Next”.

91

8. Select “Custom” and click “Settings”. When you have finished

the settings at step 9, click “Next” to continue.

9. Select “RAW” and enter “lpt1” in the “Queue Name”, click “OK”.

By default the queue name of the MFP Server is “lpt1”.

92

10. Click “Finish”.

11. Select a suitable printer manufacturer and the printer model

and click “Next”. If your printer is not in the list, click “Have
Disk…” to install the driver of the printer. After installation, the
printer model will be added to the list.

93

12. Choose to set the print whether as a default printer or not.

Click “Next”.

13. You have added the network printer to the PC successfully.

The information of the printer is displayed in the windows.
Click “Finish”.

94

11. IPP Printing

11.1 Introduction

IPP (Internet Printing Protocol) Printing provides a convenient way
of remote printing service by TCP/IP. The MFP Server can support
IPP printing in Windows 2000/XP/2003 by default. By using the
IPP printing, you can share the printer to all the PC’s that can
access the MFP Server by IP. You can even share your MFP or
printer to Internet users.

11.2 System Setup

11.2.1 MFP Server Side

It is needless to do any setting on the MFP Server side. Make sure
the MFP Server has correct IP settings. If you want to share the
printers to Internet users, you have to set a real IP to the MFP
Server. You also have to make sure that any gateway, router or
firewall does not block IPP protocol if you have these gateway
devices installed in your network.

11.2.2 Client Side

You only need to perform Window’s standard Add New Printer
procedure.

1. Click “Start”, choose “Settings” and select “Printers and Faxes”.

2. Click “Add a Printer”.

95