Edimax Office +1 operation manual
Office +1
Quick Installation Guide
12-2017 / v1.0
CONTENTS
I Quick Summary & Reminder .................................................................. 3
II Product Information .............................................................................. 4
II-1 Package Contents .................................................................................................................. 4
II-2 System Requirements ........................................................................................................... 5
II-3 Hardware Overview .............................................................................................................. 5
II-4 LED Status .............................................................................................................................. 6
II-5 Reset ...................................................................................................................................... 6
III Adding Office +1 AP to Office 1-2-3 ........................................................ 7
IV Replacing Master AP ............................................................................. 8
2
I Quick Summary & Reminder
1. You can find all supporting documents, video, and programs:
www.edimax.com/edimax_pro/download/Office1-2-3
2. For the complete Office 1-2-3 system introduction, please go to the link
below:
http://office123.edimax.com
3. During the initial power up, the master AP will automatically
communicate its settings with the Office +1 Access Point. After the
process (~10 minutes), all the settings will be set for the Office +1 AP.
4. The default username and password for Office +1 AP are admin and
1234 respectively.
After the automatic communication with the master AP, the username
and password of the Office +1 AP will change to the Master AP’s
username and password.
5. Clicking Apply during any of the configuration will reboot the AP, which
takes time, it is recommended that you use Apply only after changing
all settings.
6. If you wish to add more APs to expand your office coverage, Office
1-2-3 supports up to a total of 16 APs, please refer to the “Office +1”
package.
3
1 2 3
4
5
6
7
1. Office +1 Access Point
2. Ceiling Mount Bracket
3. Ethernet Cable
4. Quick Installation Guide
5. T-Rail Mounting Kit & Screws
6. Power Adapter
7. Ceiling Mount Screw Template
II Product Information
II-1 Package Contents
4
A
12V DC IN
12V DC port to connect the power adapter
B
LAN 1 (PoE)
LAN port with Power over Ethernet (PoE) IN
C
LAN 2
LAN port
D
Reset
Resets the device to factory default settings
A
B
C
D
II-2 System Requirements
- Existing cable/DSL modem & router.
- Existing PoE Switch connected to the router
- Computer with web browser for access point configuration
II-3 Hardware Overview
5
LED Color
LED Status
Description
Blue
On
The access point is on.
Flashing Slowly
Upgrading firmware.
Flashing Quickly
Resetting to factory defaults.
Amber
On
Starting up.
Flashing
Error.
Off
Off
The access point is off.
NOTE: You may need to use a pin or similar sharp object to push the
reset button.
II-4 LED Status
II-5 Reset
If you experience problems with your access point, you can reset the device
back to its factory settings. This resets all settings back to default.
1. Press and hold the reset button on the access point for at least 10
seconds then release the button.
2. Wait for the access point to restart. The access point is ready for setup
when the LED is blue.
6
III Adding Office +1 AP to Office 1-2-3
This quick setup is a guide to help you add the Office +1 AP to existing Office
1-2-3 high speed Wi-Fi network.
1. Identify the PoE Switch connected to existing Office 1-2-3 network.
2. Connect the Office +1 AP to the PoE Switch using an Ethernet cable.
Please make sure the Ethernet cable is connected to the PoE port of the
access point as shown below:
If you need to, remove the cap from the underside of the access point.
This creates extra space for your cables to pass through.
3. The master AP will automatically communicate its settings with the
Office +1 Access Point. After the process (~10 minutes), all the settings
will be set for the Office +1 AP.
4. Please refer to Office 1-2-3 User manual on the deployment
recommendations of the APs.
7
Loading...