Edimax IGS-5416P Service Manual
IGS-5208/ IGS-5408P/ IGS-5416P
Quick Installation Guide
02-2019 / V1.0
1
2
3
4
5
6
Product Information
I-1. Overview
The Edimax Pro IGS-5208, IGS-5408P and IGS-5416P industrial Gigabit web managed switch come
with 8 PoE+ ports (IGS-5408P and IGS-5416P only) and 2 or 4 SFP slots for high-speed Gigabit,
long-range copper or optical connections and for enduring, reliable, flexible industrial network
deployment. Supporting the redundancy of network and power, IGS series industrial switch protects
the system with uninterrupted data transmission and damage to ensure the network connection
reliability.
Dedicated ruggedized IP30-rated housing with compact aluminum alloy case to use in the harsh
environment with -40~75°C to endure wide temperature & surges range, IEC certified vibrations,
shock and free fall, industrial-grade EMC/EMS tests. It is the ideal solution for industries networks
such as automotive, factory automation, oil and gas, mining, military, transportation, substation,
energy and outdoor applications of railways, roads, tunnels, smart cities, city surveillance and traffic
monitoring.
With smart and secure features in SNMP v1/v2c/v3, PoE PD Alive Check (IGS-5408P and IGS-5416P
only), IGMP Snooping v1/v2/v3, DHCP Snooping, QoS, CoS, STP, 802.1Q VLAN, Link Aggregation
Control Protocol (LACP), Rate Control, IPv4/IPv6, Port Trunk, Mirror and etc., the IGS-5416P web
managed switch that makes managing your network easy and provides a cost effective, reliable,
scalable and secure switch solution for small to medium industrial networks.
I-2. Package Contents
IGS-5208 or IGS-5408P or
IGS-5416P Switch
Wall-Mount Kit
Console Cable
DIN-Rail Kit
DC Power Terminal Block x 2
1
Quick Installation Guide
I-3. Hardware Overview
1. Dimension
IGS-5208: 145 mm (H) x 72.20 mm (W) x 113 mm (D)
IGS-5408P: 145 mm (H) x 72.20 mm (W) x 113 mm (D)
2
IGS-5416P: 145 mm (H) x 90.80 mm (W) x 113 mm (D)
2. DIN-Rail mount
The DIN-Rail clip is already attached on the rear side of the switch supports EN 50022 standard DIN
Rail, in the following diagram includes the dimension of EN 50022 DIN Rail.
Follow the steps below to mount the switch on the DIN-Rail track.
1. Insert the upper end of the DIN-Rail clip into the
back of the DIN-Rail track from its upper side
2. Lightly push the bottom of the DIN-Rail clip into the
track.
3. Check if the DIN-Rail clip is tightly attached to the
track.
4. To remove the switch from the track, reverse the
steps above.
3
3. Wall mount
Screw the wall-mount brackets with screws
in the accessory kit
4. Wiring Power Inputs
1. Insert the positive and negative wires into the PWR1 (+,-) and PWR2
(+,-) on the 4-contact terminal block connector.
2. Tighten the screws to prevent the wires from loosening.
5. Wiring Fault Alarm
1. Insert the wires into the left two contacts of the 4-contact terminal
block (Fault Alarm Relay).
2. Tighten the screws to prevent the wires from loosening.
3. The relay will detect the power and link failure.
4. Users can connect the relay to an alarm and buzzer so that when the
relay forms an open circuit, the users will be notified.
6. Wiring Digital Inputs
Insert the positive and negative wires into the right two contacts (+,-) of the
4-contact terminal block (DI).
1. Tighten the screws to prevent the wires from loosening.
2. The system will detect the voltage go through the DI.
˙ +13 to +30V for state "1"
˙ -30 to +3V for state "0"
˙ Max. input current: 8mA
7. USB Port
A USB port is available on the switch that is located between the Console port
and Reset button. This USB port provides the following features:
˙ Backup/Restore Configurations
˙ Auto-Load configuration from USB
˙ Auto-Backup configuration to USB
˙ Save system logs to USB
4
Loading...