Edimax HP-5102Wn User Manual

HP-5102Wn

User Manual

12-2014 / v1.0

COPYRIGHT

Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission from Edimax Technology Co., Ltd.

Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability, or fitness for any particular purpose. Any software described in this
manual is sold or licensed as is. Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right
to revise this publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. For more information about this product, please refer to the
user manual on the CD-ROM. The software and specifications are subject to change
without notice. Please visit our website www.edimax.com for updates. All brand and
product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.

Edimax Technology Co., Ltd.

Add: No. 3, Wu-Chuan 3rd Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan
Tel: [phone]
Email: [e-mail]

Notice According to GNU General Public License Version 2

This product includes software that is subject to the GNU General Public License version

2. The program is free software and distributed without any warranty of the author. We
offer, valid for at least three years, to give you, for a charge no more than the costs of
physically performing source distribution, a complete machine-readable copy of the
corresponding source code.

CONTENTS

I. PRODUCT INFORMATION ............................................................................................................. 1

I-1. Package Contents ...................................................................................................................... 1

I-2. Hardware ................................................................................................................................... 2

I-3. LED Status .................................................................................................................................. 3

I-4. Resetting the Powerline Adapter .............................................................................................. 4

I-5. Safety Information ..................................................................................................................... 5

II. POWERLINE NETWORK ................................................................................................................ 6

II-1. Installation ................................................................................................................................. 6

II-2. Leaving a Powerline Network .................................................................................................... 8

II-3. WPS Setup ................................................................................................................................. 9

III. WI-FI CONFIGURATION .............................................................................................................. 10

III-1. Setup Wizard .......................................................................................................................... 12

III-2. Device Configuration .............................................................................................................. 13

III-3. WLAN Configuration ............................................................................................................... 14

III-4. Status Overview ...................................................................................................................... 16

III-5. Management .......................................................................................................................... 17

III-5-1. Account ............................................................................................................................ 18

III-5-2. DHCP Server ..................................................................................................................... 19

III-5-3. Factory Restore ................................................................................................................ 20

III-5-4. WLAN Radio Configuration .............................................................................................. 21

IV. POWERLINE UTILITY SOFTWARE ................................................................................................ 23

IV-1. Using the Utility ...................................................................................................................... 24

IV-1-1. Main ................................................................................................................................. 24

IV-1-2. Diagnostics ....................................................................................................................... 26

IV-1-3. About ................................................................................................................................ 27

V. APPENDIX ................................................................................................................................. 28

V-1. Windows XP ............................................................................................................................. 28

V-2. Windows Vista......................................................................................................................... 29

V-3. Windows 7 ............................................................................................................................... 30

V-4. Windows 8/8.1 ......................................................................................................................... 32

V-5. Mac OS ..................................................................................................................................... 36

V-6. Glossary ................................................................................................................................... 38

1

I. PRODUCT INFORMATION

I-1. Package Contents

Before you start using this product, please check if there is anything missing in

the package, and contact your dealer to claim the missing items(s):

HP-5102Wn

Ethernet Cable

CD-ROM

Quick Installation Guide

2

I-2. Hardware

1

LEDs

See I-3. LED Status below.

2

Reset/Group

Button

Press for 10+ seconds to reset the HP-5102Wn Powerline
function (PLC utility settings) to factory defaults, and less
3 seconds to connect with another Powerline adapter.
Press for 5 - 8 seconds to leave an encrypted powerline
network group.

3

WPS Button

Press for 10+ seconds to reset the Wi-Fi functions (web
U.I. settings) to factory defaults and less than 2 seconds to
activate WPS (see II-3. WPS Setup).

4

Ethernet Port

Connect a computer or Ethernet device to the
HP-5102Wn.

5

On/Off Switch

Switch the HP-5102Wn on or off.

3

I-3. LED Status

LED

Color

LED Status

Description

Power

Green

On

HP-5102Wn is on.

Flashing

Establishing Powerline
connection.

Off

HP-5102Wn is off.

PLC

Green

On

Powerline connection
detected.

Flashing

Powerline traffic: excellent
connection.

Off

No Powerline connection
detected.

Orange

Flashing

Powerline traffic: good
connection.

Red

Flashing

Powerline connection: bad
connection.

LAN

Green

On

LAN port connected.

Flashing

LAN activity (transferring or
receiving data).

Off

LAN port not connected.

Wi-Fi

Green

On

WPS is active.

Flashing

Wireless activity (transmitting
or receiving data).

Off

No wireless activity.

4

I-4. Resetting the Powerline Adapter

If you experience a problem with your HP-5102Wn you can reset the device
back to its factory default settings.

To reset Powerline settings, press and hold the Reset/Group button for at
least 10 seconds. The power LED ( ) will display on when the HP-5102Wn is
ready (see LED Status).

To reset Wi-Fi settings, press and hold the WPS button for 10+ seconds.

5

I-5. Safety Information

In order to ensure the safe operation of the device and its users, please read
and act in accordance with the following safety instructions.

1. The powerline adapter is designed for indoor use only; do not place the
powerline adapter outdoors.

2. Do not place the powerline adapter in or near hot/humid places, such as a
kitchen or bathroom.

3. Do not pull any connected cable with force; carefully disconnect it from the
powerline adapter.

5. The device contains small parts which are a danger to small children under
3 years old. Please keep the powerline adapter out of reach of children.

6. Do not place the powerline adapter on paper, cloth, or other flammable
materials. The powerline adapter will become hot during use.

7. There are no user-serviceable parts inside the powerline adapter. If you
experience problems with the powerline adapter, please contact your
dealer of purchase and ask for help.

8. The powerline adapter is an electrical device and as such, if it becomes wet
for any reason, do not attempt to touch it without switching the power
supply off. Contact an experienced electrical technician for further help.

6

II. POWERLINE NETWORK

A minimum of two Powerline devices are required to establish
a Powerline network.

For best performance, plug Powerline adapters directly into
standard wall sockets. Avoid using multi-socket adapters.

It may be convenient to install and configure your Powerline
adapters in the same room, and then relocate the HP-5102Wn
to its preferred location after setup is complete.

II-1. Installation

1. Connect a Powerline adapter to your router via Ethernet cable and plug it

into a power socket. The power and LAN LEDs should display on.

2. Plug the HP-5102Wn into a power socket, and confirm the power LED is on.

3. The PLC LED on both Powerline adapters should indicate that a Powerline

connection is established. For the HP-5102Wn the PLC LED will display on
(see LED Status).

7

4. If you want to create a private network, press the “Reset/Group” button on

each Powerline adapter for less than 3 seconds, within 2 minutes of each
other. The adapters will automatically group together and generate an
encrypted network.

5. To connect to your HP-5102Wn’s Wi-Fi, use a Wi-Fi device (e.g. computer,

tablet, smartphone) to search for a Wi-Fi network with the SSID

“EdimaxPLC_***” and connect to it. The password is displayed on the

product label.

Note: The last three characters of the SSID are unique

to your device. The full SSID & password is displayed
on the product label as shown below.

Note: Alternatively, you can use the WPS button as

described later in II-3. WPS Setup.

8

6. You can also use an Ethernet cable to connect a computer or other device

to the HP-5102Wn using the Ethernet port on the underside of the product.

II-2. Leaving a Powerline Network

Press the “Reset/Group” button on the powerline adapter for 5–8 seconds to
leave a Powerline network that the HP-5102Wn is connected to. The
HP-5102Wn will be disconnected/ungrouped from its network and ready to
reconnect to any Powerline network.

9

II-3. WPS Setup

If your wireless device supports WPS (Wi-Fi Protected Setup) then you can use
this method to connect to the HP-5102Wn’s Wi-Fi after you have established
a Powerline connection.

1. Press the WPS button on the HP-5102Wn for less than 2 seconds to

activate WPS. The HP-5102Wn’s Wi-Fi LED will display on to indicate that
WPS is active.

2. Within two minutes, press the WPS button on your wireless device to

activate WPS. The devices will establish a connection.

Note: Please check the instructions for your

wireless device for how long you need to hold
down its WPS button to activate WPS.

10

III. WI-FI CONFIGURATION

To make configurations to your HP-5102Wn (e.g. change the SSID & password)
you can use the product’s web-based control panel. To access the control
panel, follow the instructions below:

Note: By default, the HP-5102Wn is set to use a

dynamic IP address from your router. This means that
order to access the control panel as shown here using
the default IP address, the HP-5102Wn must be
disconnected from your router. If using a dynamic IP
or if you later set your powerline adapter to use a
static IP address – then you do not need to disconnect
the HP-5102Wn from your router to access the control
panel. In such cases, use the new IP address to access
control panel instead.

1. Connect your computer to the HP-5102Wn using Wi-Fi (Default SSID:

EdimaxPLC_*** see product label) or using an Ethernet cable as shown

below:

2. Change your computer’s IP address to 192.168.2.x where x = any number

between 3 and 254. Refer to the appendix if you need help.

11

Note: If you later change your HP-5102Wn’s IP address

then please adjust this step to ensure your computer’s

IP address is in the same subnet.

3. Go to 192.168.2.2 in a web browser and you will arrive at the login screen,

as shown below. The default username is admin and the default password
is 1234.

Note: If you cannot access the control panel, please

unplug your HP-5102Wn and plug it back in, and try
again.

12

III-1. Setup Wizard

Click “Start Setup Wizard” to set the SSID and password of the powerline

adapter.

Name (SSID)

Enter the network name(SSID) name for the
Wi-Fi network. The SSID can consist of any
combination of up to 32 alphanumeric
characters.

Password

Enter a password of 8 – 63 characters for the
SSID.

13

III-2. Device Configuration

Select “DHCP” for your powerline adapter to be assigned a dynamic IP address
from your router’s DHCP server, or select “Fixed IP” to manually specify a
static/fixed IP address for your powerline adapter. When using “DHCP” check
your router’s settings to find your powerline adapter’s IP address.

Fixed IP

IP Address

Specify a static IP address here. This IP
address will be assigned to your powerline
adapter and will replace the default IP
address.

Subnet Mask

Specify a subnet mask. The default value is

255.255.255.0

Note: If you assign a new IP address to your powerline

adapter, use this IP address in a web browser to access
the control panel, and ensure your computer’s IP
address is in the same subnet.

14

III-3. WLAN Configuration

The powerline adapter provides three security/encryption options. When data is

encrypted, information transmitted wirelessly cannot be read by anyone who
does not know the correct encryption key. By default, WPA encryption is
enabled.

It’s essential to configure wireless security in order to prevent

unauthorised access to your network.

Select hard-to-guess passwords which include combinations of
numbers, letters and symbols, and change your password
regularly.

15

Name (SSID)

Enter the network name (SSID) for the Wi-Fi
network. The SSID can consist of any
combination of up to 32 alphanumeric
characters.

Channel

Select a radio channel for your Wi-Fi or use
the auto setting. Selecting a less-crowded
channel can improve performance due to less
interference from other Wi-Fi devices. See
below for information about country-specific
restrictions.
Channels 1-11 approved for use in the United
States, Canada, Latin America, and Taiwan.

Channels 1-14 approved for use in Japan.
Channels 1-13 approved for use in other

countries.

Security Settings

Open

Authentication is disabled and no
password/key is required to connect to the
powerline adapter. Not recommended.

WEP

WEP (Wired Equivalent Privacy) is a
basic encryption type. Enter a security
key. For a higher level of security
consider using WPA encryption below.

WPA

WPA is a secure wireless encryption
type with strong data protection and
user authentication, utilizing 128-bit
encryption keys. Select from WPA,
WPA2 or both. WPA2 is safer than WPA
only, but not supported by all wireless
clients. Selecting both will use WPA2
where supported by clients. Please
make sure your wireless client supports
your selection. Enter your security key.

16

III-4. Status Overview

Displays the current firmware version and the MAC address of any wireless
clients which are connected to the powerline adapter.

17

III-5. Management

The sub-menu provides access to various management settings:

18

III-5-1. Account

Account settings are the username and password used to log in to the control
panel. The default values are username: admin password: 1234. It is
recommended to change account settings according to your preference.

19

III-5-2. DHCP Server

Enable or disable the powerline adapters DHCP server. The DHCP server will
automatically assign an IP address to network devices connected to the
powerline adapter. You can specify a range of IP address to assign.

Do not enable DHCP server is your router has also enabled DHCP
server.

First IP Address

Enter the start IP address for the DHCP
server’s IP address leases.

Last IP Address

Enter the end IP address for the DHCP
server’s IP address leases.

20

III-5-3. Factory Restore

You can restore the powerline adapter back its factory default state. This
resets all settings including SSID, password and IP settings.

21

III-5-4. WLAN Radio Configuration

You can configure the powerline adapter’s Wi-Fi radio.

Name (SSID)

Enter the network name (SSID) for the Wi-Fi
network. The SSID can consist of any
combination of up to 32 alphanumeric
characters.

Channel

Select a radio channel for your Wi-Fi or use
the auto setting. Selecting a less-crowded
channel can improve performance due to less
interference from other Wi-Fi devices. See
below for information about country-specific
restrictions.
Channels 1-11 approved for use in the United
States, Canada, Latin America, and Taiwan.

Channels 1-14 approved for use in Japan.
Channels 1-13 approved for use in other

countries.

Mode

Select the wireless standard used for the
powerline adapter from 802.11g & 802.11n.

22

Channel Width

Select wireless channel width (bandwidth
used by wireless signals from the device) – the
recommended value is HT20/40.

23

IV. POWERLINE UTILITY SOFTWARE

The included CD-ROM contains Powerline utility software which provides
powerline diagnostic information and management for advanced users.

Before installating the utility software, please uninstall any
existing Powerline utility software you may already have.

To install the utility software, insert the CD into your CD-ROM drive and the
setup wizard should begin automatically. If not, please manually locate and
open the “AutoRun.exe” file in the CD.

1. When the following screen appears, select your model.

2. Click “Setup Utility” and follow the on-screen instructions.

24

IV-1. Using the Utility

The following pages describe the functions of each tab within the Powerline
utility software.

IV-1-1. Main

The “Main” tab provides a list of Powerline adapters connected to the network.
Use the drop down menu to select a network card if you have more than one
installed on your computer.

25

Name

This column shows the default device name, for
example: “Device 2”, “Device 3”. If you want to
change the name, please click “Set Name” button
to edit the name.

MAC Address

The adapter’s MAC address will be shown here.

Password

This column by default is blank. In order to
manage the powerline adapters, you have to enter
the password of the adapter. The password is
printed on the label located on the back of the
powerline adapter. After you have entered the
correct password, this column will show the
password.

To set the password of the adapter, first select the
adapter by clicking on its name and then click
“Enter Password” button. A dialog box will appear
as below. Please type the password and click “OK”
button.

Quality

The status of the connection quality will be shown
here.

Speed (Mbps)

Shows the current data rate of the powerline
adapter.

Set Name

Select a device and click “Set Name” to rename
the device.

Enter Password

Click “Enter Password” to set up a password for
the selected device.

Scan

Perform a scan of other remote Powerline
adapters. By default, the utility automatically scans
every few seconds.

26

Security

Network Name

Powerline adapters often ship with the same
default network name “HomePlugAV”. Powerline
adapters with the same network name can be
connected together.

If you want to create another network, please
enter the new network name and select “Set all
remote devices whose password has been
entered” or “Set Local Device Only” below.

Set All Remote
Devices Whose
Password Has Been
Entered

Change the network name of all devices that
appear in box above whose password has been
entered.
Set Local Devices

Change the network name for local devices only.

IV-1-2. Diagnostics

The “Diagnostics” tab displays the system information and history of all

remote devices. The upper panel displays technical data concerning the
software and hardware on the host computer and the lower panel displays the
history of all remote devices. Click “Save Report” to save the report to local
storage.

27

IV-1-3. About

The “About” tab displays basic information about the software.

28

V. APPENDIX

How to Modify the IP Address of Your PC or Mac

Please follow the instructions appropriate for your operating system. In the
following examples we use the IP address 192.168.2.10.

V-1. Windows XP

1. Click the “Start” button (it should be located in the lower-left corner of your

computer), then click “Control Panel”. Double-click the “Network and
Internet Connections” icon, click “Network Connections”, and then

double-click “Local Area Connection”. The “Local Area Connection Status”
window will then appear, click “Properties”.

2. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10
Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

29

V-2. Windows Vista

1. Click the “Start” button (it should be located in the lower-left corner of your

computer), then click “Control Panel”. Click “View Network Status and
Tasks”, then click “Manage Network Connections”. Right-click “Local Area
Network”, then select “Properties”. The “Local Area Connection Properties”
window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”,
and then click “Properties”.

2. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10
Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

30

V-3. Windows 7

1. Click the “Start” button (it should be located in the lower-left corner of your

computer), then click “Control Panel”.

2. Under “Network and Internet” click “View network status and tasks”.

31

3. Click “Local Area Connection”.

4. Click “Properties”.

32

5. Select “Internet Protocol Version 4 (TCP/IPv6) and then click “Properties”.

6. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10
Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

V-4. Windows 8/8.1

1. From the Windows 8 Start screen, you need to switch to desktop mode.

Move your curser to the bottom left of the screen and click.

33

2. In desktop mode, click the File Explorer icon in the bottom left of the

screen, as shown below.

34

3. Right click “Network” and then select “Properties”.

4. In the window that opens, select “Change adapter settings” from the left

side.

35

5. Choose your connection and right click, then select “Properties”.

6. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.

36

7. Select “Use the following IP address”, then input the following values:

IP address: 192.168.2.10
Subnet Mask: 255.255.255.0

Click ‘OK’ when finished.

V-5. Mac OS

1. Have your Macintosh computer operate as usual, and click on “System

Preferences”

2. In System Preferences, click on “Network”.

3. Here you will see all of your network connections. Network Preferences will

now display an Ethernet adapter, as shown below. The status of “Ethernet”
should be “Connected”.

37

4. Click on “Ethernet” in the left panel and then click the drop down arrow for

the menu labeled “Configure IPv4” in the right panel. From the drop down
menu, select “Manually”.

5. In the panel on the right side, enter IP address 192.168.2.10 and subnet

mask 255.255.255.0. Click on “Apply”.

6. In the left sidebar, “Ethernet” should now display “Connected” as shown

below. In the right panel, you should see the IP address 192.168.2.10 and
subnet mask 255.255.255.0.

38

V-6. Glossary

Default Gateway (Wireless bridge): Every non-access point IP device needs to

configure a default gateway’s IP address. When the device sends out an IP

packet, if the destination is not on the same network, the device has to send
the packet to its default gateway, which will then send it out towards the
destination.

DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives
every computer on your home network an IP address.

DNS Server IP Address: DNS stands for Domain Name System, which allows
Internet servers to have a domain name (such as www.Broadbandaccess
point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server
keeps a database of Internet servers and their respective domain names and
IP addresses, so that when a domain name is requested (as in typing
"Broadbandaccess point.com" into your Internet browser), the user is sent to
the proper IP address. The DNS server IP address used by the computers on
your home network is the location of the DNS server your ISP has assigned to
you.

DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your
existing phone lines to transmit data at high speeds.

Ethernet: A standard for computer networks. Ethernet networks are
connected by special cables and hubs, and move data around at up to 10/100
million bits per second (Mbps).

IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP
address consists of a series of four numbers separated by periods, that
identifies a single, unique Internet computer host in an IP network. Example:

192.168.2.1. It consists of 2 portions: the IP network address, and the host

identifier.

The IP address is a 32-bit binary pattern, which can be represented as four

cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each
“aaa” can be anything from 000 to 255, or as four cascaded binary numbers
separated by “.”: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b”

can either be 0 or 1.

A network mask is also a 32-bit binary pattern, and consists of consecutive
leading 1’s followed by consecutive trailing 0’s, such as

39

11111111.11111111.11111111.00000000. Therefore sometimes a network

mask can also be described simply as “x” number of leading 1’s.
When both are represented side by side in their binary forms, all bits in the IP

address that correspond to 1’s in the network mask become part of the IP

network address, and the remaining bits correspond to the host ID.

For example, if the IP address for a device is, in its binary form,

11011001.10110000.10010000.00000111, and if its network mask is,

11111111.11111111.11110000.00000000

It means the device’s network address is

11011001.10110000.10010000.00000000, and its host ID is,

00000000.00000000.00000000.00000111. This is a convenient and efficient

method for access points to route IP packets to their destination.

ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an
IP address for the Internet access point located at the ISP's office.

ISP: Internet Service Provider. An ISP is a business that provides connectivity
to the Internet for individuals and other businesses or organizations.

LAN: Local Area Network. A LAN is a group of computers and devices
connected together in a relatively small area (such as a house or an office).
Your home network is considered a LAN.

MAC Address: MAC stands for Media Access Control. A MAC address is the
hardware address of a device connected to a network. The MAC address is a
unique identifier for a device with an Ethernet interface. It is comprised of
two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique

for each manufacturer), plus 3 bytes that are often used as the product’s

serial number.

NAT: Network Address Translation. This process allows all of the computers
on your home network to use one IP address. Using the broadband access

point’s NAT capability, you can access the Internet from any computer on

your home network without having to purchase more IP addresses from your
ISP.
Port: Network Clients (LAN PC) uses port numbers to distinguish one network
application/protocol over another. Below is a list of common applications and
protocol/port numbers:

Application

Protocol

Port Number

40

Telnet

TCP

23

FTP

TCP

21

SMTP

TCP

25

POP3

TCP

110

H.323

TCP

1720

SNMP

UCP

161

SNMP Trap

UDP

162

HTTP

TCP

80

PPTP

TCP

1723

PC Anywhere

TCP

5631

PC Anywhere

UDP

5632

Access point: A access point is an intelligent network device that forwards
packets between different networks based on network layer address
information such as IP addresses.

Subnet Mask: A subnet mask, which may be a part of the TCP/IP information
provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured
like an IP address. It is used to create IP address numbers used only within a
particular network (as opposed to valid IP address numbers recognized by the
Internet, which must be assigned by InterNIC).
TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and
Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data
transmission over the Internet. Both TCP and UDP are transport layer protocol.
TCP performs proper error detection and error recovery, and thus is reliable.
UDP on the other hand is not reliable. They both run on top of the IP (Internet
Protocol), a network layer protocol.

WAN: Wide Area Network. A network that connects computers located in
geographically separate areas (e.g. different buildings, cities, countries). The
Internet is a wide area network.

Web-based management Graphical User Interface (GUI): Many devices
support a graphical user interface that is based on the web browser. This
means the user can use the familiar Netscape or Microsoft Internet Explorer
to Control/configure or monitor the device being managed.

41

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna
or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance could void the authority
to operate equipment.

Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to
the antenna shall not be less than 2.5cm (1 inch) during normal operation.

Federal Communications Commission (FCC) RF Exposure Requirements
This EUT is compliance with SAR for general population/uncontrolled exposure limits in ANSI/IEEE
C95.1-1999 and had been tested in accordance with the measurement methods and procedures
specified in OET Bulletin 65 Supplement C. The equipment version marketed in US is restricted to usage
of the channels 1-11 only.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal
equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and
replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth
Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus,
Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey,
and United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states:
Iceland, Liechtenstein, Norway, and Switzerland.

EU Countries Not Intended for Use
None

42

EU Declaration of Conformity

English: This equipment is in compliance with the essential requirements and other relevant

provisions of Directive 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

French: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive

1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.

Czechian: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními

směrnic 1999/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES.

Polish: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami

określonymi Dyrektywą UE 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

Romanian: Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale

Directivei 1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.

Russian: Это оборудование соответствует основным требованиям и положениям Директивы

1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek

(1999/5/EK, 2009/125/EK, 2006/95/EK, 2011/65/EK).

Türkçe: Bu cihaz 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC direktifleri zorunlu istekler ve

diğer hükümlerle ile uyumludur.

Ukrainian: Обладнання відповідає вимогам і умовам директиви 1999/5/EC, 2009/125/EC,

2006/95/EC, 2011/65/EC.

Slovakian: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc

1999/5/ES, 2009/125/ES, 2006/95/ES, 2011/65/ES.

German: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 1999/5/EC, 2009/125/EC,

2006/95/EC, 2011/65/EC.

Spanish: El presente equipo cumple los requisitos esenciales de la Directiva 1999/5/EC, 2009/125/EC,

2006/95/EC, 2011/65/EC.

Italian: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili

della Direttiva 1999/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE.

Dutch: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van

richtlijn 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

Portugese: Este equipamento cumpre os requesitos essênciais da Directiva 1999/5/EC, 2009/125/EC,

2006/95/EC, 2011/65/EC.

Norwegian: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv

1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

Swedish: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta

bestämmelser i direktiv 1999/5/EG, 2009/125/EG, 2006/95/EG, 2011/65/EG.

Danish: Dette udstyr er i overensstemmelse med de væsentligste krav og andre relevante

forordninger i direktiv 1999/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC.

Finnish: Tämä laite täyttää direktiivien 1999/5/EY, 2009/125/EY, 2006/95/EY, 2011/65/EY oleelliset

vaatimukset ja muut asiaankuuluvat määräykset.

-------------------------------------------------------------------------------------------------------------

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It should
be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or
returned to the supplier for disposal.

43

Declaration of Conformity

We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the
equipment described below complies with the requirements of the European R&TTE
directive.

Equipment:

AV500 PowerLine Wi-Fi Extender

Model No.:

HP-5102Wn

The following European standards for essential requirements have been followed:

Directives 1999/5/EC

Spectrum:

ETSI EN 300 328 V1.7.1:2006

EMC:

ETSI EN 301 489-1 V1.9.2:2011

ETSI EN 301 489-17 V2.1.1:2009

Recommendation 99/519/EC

EMF:

EN 62311:2008

Directives 2004/108/EC

EMC:

EN 55022: 2010 CISPR/I/257/CD:2008

EN 61000-3-2: 2006+A2:2009
EN 61000-3-3: 2008
EN 50412-2-1: 2005
IEC 61000-4-2: 2008; IEC 61000-4-3: 2010

IEC 61000-4-4: 2012; IEC 61000-4-5: 2005

IEC 61000-4-6: 2008; IEC 61000-4-8: 2009
IEC 61000-4-11: 2004

Directives 2006/95/EC

Safety (LVD):

EN 60950-1: 2006 +A11: 2009 + A1: 2010 + A12: 2011
IEC 60950-1:2005+A1:2009

Edimax Technology Co., Ltd.
No. 3, Wu Chuan 3rd Road,
Wu-Ku Industrial Park,
New Taipei City, Taiwan

Date of Signature:

December, 2014

Signature:

Printed Name:

Albert Chang

Title:

Director

Edimax Technology Co., Ltd.

44

HP-5102AC

User Manual

02-2013 / v1.0

1

COPYRIGHT

Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission from Edimax Technology Co.,
Ltd.

Edimax Technology Co., Ltd. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability, or fitness for any particular purpose.
Any software described in this manual is sold or licensed as is. Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Edimax Technology Co., Ltd. reserves the right to
revise this publication and to make changes from time to time in the contents
hereof without the obligation to notify any person of such revision or changes.

The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more information about this product,
please refer to the user manual on the CD-ROM. The software and specifications
are subject to change without notice. Please visit our website www.edimax.com
for updates. All brand and product names mentioned in this manual are
trademarks and/or registered trademarks of their respective holders.

Edimax Technology Co., Ltd.

Add: No. 3, Wu-Chuan 3rd Rd., Wu-Ku Industrial Park, New Taipei City, Taiwan
Tel: [phone]
Email: [e-mail]

2

Contents

Chapter 1: Introduction ..................................................................................................................................... 3

1.1 Product Features .................................................................................................................................. 3

1.2 Application ........................................................................................................................................... 3

1.3 Compatibility ........................................................................................................................................ 4

1.4 System Requirements .......................................................................................................................... 4

Chapter 2: About the Product ............................................................................................................................ 5

2.1 LED Definitions ..................................................................................................................................... 5

2.2 Interface ............................................................................................................................................... 6

2.3 Fast Ethernet Port ................................................................................................................................ 6

Chapter 3:Utility Software Installation .............................................................................................................. 7

3.1 Win 8 .................................................................................................................................................... 7

3.2 Win XP/Vista / 7 ................................................................................................................................. 15

Chapter 4: Using the Utility Software .............................................................................................................. 21

4.1 Main Tab ............................................................................................................................................ 21

4.2 Diagnostics Tab .................................................................................................................................. 22

4.3 About Tab ........................................................................................................................................... 23

Chapter 5: Group Button ................................................................................................................................. 24

5.1 Forming a HomePlug AV Logical Network ......................................................................................... 24

5.2 Joining a Network .............................................................................................................................. 25

5.3 Leaving a Network & Joining another Network ................................................................................. 26

Chapter 6: Troubleshooting ............................................................................................................................. 27

3

Chapter 1: Introduction

1.1 Product Features

 Easy plug-n-play setup and 128-bit AES security
 Max. powerline speed up to 500Mbps
 Backward compatible with 200Mbps powerline adapters
 Features energy saving mode to reduce power consumption
 Utilizes existing electrical wires to transmit network data
 Powerline transmission range up to 300 meters

1.2 Application

 High-definition (HD) and standard-definition (SD) video distribution
 Broadband Internet sharing
 Internet Protocol Television (IPTV) and Voice over Internet Protocol (VoIP)

applications

4

1.3 Compatibility

500Mbps powerline devices (HomePlug AV standard) are incompatible and cannot be

used with 14Mbps and 85Mbps powerline devices (HomePlug 1.0 and 1.1 standards).

1.4 System Requirements

Operating System

Utility supports Windows XP/Vista/7/8

CPU

Intel Pentium III 1.0GHz (or above)

RAM

256MB (or above)

Free Disk Space

100MB (or above)

Network Interface

Ethernet port (100Mbps or above) and an Ethernet cable

5

Chapter 2: About the Product

2.1 LED Definitions

LED

Status

Description

LAN

Green

LAN port connected

Blinking

LAN activity (transferring data)

Off

LAN port not connected

PLC

Green/Yellow

The green indicator turns on and the yellow indicator
blinks slowly when the device is detecting a
powerline link.
The green indicator turns on and the yellow indicator
blinks quickly to indicate data is being transferred
over the powerline link.

Off

No other PLC device detected

PWR

Green

Powered on

Off

Powered off

Note: The device will enter standby mode, and all LEDs will extinguish, after

5 seconds without any data transfer, including when the Ethernet cable is
disconnected. The Power LED will flash once every 15 seconds.

6

2.2 Interface

Interface

Description

Integrated
Power Socket

The integrated electrical socket enables additional terminal
devices or multiple socket to be connected to the adapter, just
as a normal wall socket would.

Ethernet Port

This is a Fast Ethernet port for connecting to a computer or
other devices with a network port.

Group/Reset

Creates an encrypted powerline network group automatically
(press the button for less than 3 seconds).

Leaves an encrypted powerline network group
(press the button for 5~8 seconds).

Restores the powerline adapter to factory defaults (press the
button for 10~15 seconds).

2.3 Fast Ethernet Port

You can connect the powerline adapter to a router, a computer, or any network device
via this Fast Ethernet port.

7

Chapter 3:Utility Software Installation

3.1 Win 8

Step 1 Before installing the utility software, make sure that no other powerline utility is

installed on your computer. If any other utility software is installed, uninstall it and
reboot the computer.

Step 2 Insert the CD into your CD-ROM drive. When the following EZmax Wizard appears,

select your model.

Step 3 Then click “Setup Utility”.

8

Step 4 Click right button on WinPCap4.1.2 then click “Properties”.

Step 5 Click Compatibility tab and check “Run this program in compatibility mode for:",

then select Windows 7, then click “Apply”.

9

Step 6 Then click “WinPcap_4_1_2”. The wizard will guide you through the setup process.

Step 7 When the following WinPcap Compatibility Assistant appears, select Run the

program without getting help.

10

11

Step 8 After the installation is complete, click “Finish”.

12

Step 9 Click the “Edimax PowerLine Utility”, the “PLC 500Mbps Utility” appears, click
“Next” to continue.

Step 10 Select where you want to install the utility software, and then click “Next”.

13

Step 11 After the installation is complete, click “Close”.

14

Step 12 An icon will appear on your desktop. Click the icon to open the utility software.

Note: You can manage all the connected powerline adapters with the utility

software. However, installing the utility software is optional.

15

3.2 Win XP/Vista / 7

Step 1 Before installing the utility software, make sure that no other powerline utility is

installed on your computer. If any other utility software is installed, uninstall it and
reboot the computer.

Step 2 Insert the CD into your CD-ROM drive. When the following EZmax Wizard appears,

select your model.

Step 3 Then click “Setup Utility”.

16

Step 4 If you have not installed WinPcap version 4.1.2 (or higher) on your computer

before. The wizard will guide you through the setup process.

17

18

Step 5 When the “Edimax PowerLine Utility” setup wizard appears, click “Next” to
continue.

Step 6 In the “License Agreement” screen, please select “I Agree” and then click “Next” to
continue.

19

Step 7 Select where you want to install the utility software, and then click “Next”.

Step 8 If you confirm to install the utility, click “Next”.

20

Step 9 After the installation is complete, click “Close”.

Step 10 An icon will appear on your desktop. Click the icon to open the utility software.

Note: You can manage all the connected powerline adapters with the utility

software. However, installing the utility software is optional.

21

Chapter 4: Using the Utility Software

4.1 Main Tab

The “Main” tab provides a list of powerline adapters connected to the network. The
upper panel displays local powerline adapters. The lower panel displays remote powerline
adapters in the network.

Set Name

Select a device and click “Set Name” to rename the device.

Enter Password

By default, this column is blank. Select a device and click
“Enter Password” to set up a password for the device.

Scan

Click “Scan” and the utility software will perform an
immediate scan of other remote powerline adapters. By
default, the utility automatically scans every few seconds.

22

4.2 Diagnostics Tab

The “Diagnostics” tab displays the system information and history of all remote
devices.

The upper panel displays technical data concerning the software and hardware on the
host computer and the lower panel displays the history of all remote devices.

23

4.3 About Tab

The “About” tab contains some basic information about the software. You can also
enable or disable the autoscan function under “Preferences”.

24

Chapter 5: Group Button

This section demonstrates how to add or remove devices from a HomePlug AV network
with the “Group” button.

5.1 Forming a HomePlug AV Logical Network

When two devices with different group keys are connected to the same powerline and
you want them to form a logical network, follow the following procedures:

Step 1 Press and hold the “Group” button on adapter A for less than 3 seconds. The

Power LED will start to blink.

Step 2 Within 120 seconds after the Power LED starts blinking on adapter A, press the

“Group” button on adapter B for less than 3 seconds.

Step 3 Wait for the connection to be established.

25

5.2 Joining a Network

If you want to add a new powerline device to an existing network, follow the following
procedures:

Step 1 Press the “Group” button on an adapter in the existing network (adapter A or B) for

less than 3 seconds. The Power LED will start to blink.

Step 2 Within 120 seconds after the Power LED starts blinking on adapter A or B, press

the “Group” button on the new adapter (adapter C) for at least 3 seconds.

Step 3 Wait for the connection to be established.

26

5.3 Leaving a Network & Joining another Network

If you want to remove a powerline device from an existing network and add it to
another network, follow the following procedures:

Step 1 Press the “Group” button on the adapter to be removed (adapter B) for at least 10

seconds.

Step 2 Wait for adapter B to be disconnected with adapter A & C.

Step 3 Press the “Group” button on an adapter in another network (adapter D) for less

than 3 seconds. The Power LED will start to blink.

Step 4 Within 120 seconds after the Power LED starts blinking on adapter D, press the

“Group” button on adapter B for at least 3 seconds.

Step 5 Wait for the connection to be established.

27

Chapter 6: Troubleshooting

If your powerline adapters have difficulty communicating with each other, try the

following procedures:

 Try power cycling the unit by unplugging it from the electric outlet for 10 seconds and

plugging it in again.

 Use a pin to hold the reset button down for 2 seconds on each unit you are trying to

connect. The units will reset and attempt to establish a connection using factory default
settings.

 Try plugging the powerline adapter into an adjacent electric outlet.
 Powerline adapters work better when plugged directly into an electric outlet. Using a

power strip or surge protector may degrade network performance or completely block
network signals.

 This powerline adapter should not be used on GFI protected electric outlets, as some

outlets will filter out the powerline signal.

 This powerline adapter should not be used in areas with excessive heat.
 Certain florescent or incandescent lights are noise sources that can degrade

performance.

 If your building has more than one circuit breaker box, your powerline adapters may not

be able to establish a connection across different circuit breaker boxes. In such cases, try
establishing a connection across different circuit breaker boxes by linking two powerline
adapters together with an Ethernet cable.

28

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio technician for help.

FCC Caution

This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the authority to operate equipment.

Federal Communications Commission (FCC) Radiation Exposure Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be
less than 2.5cm (1 inch) during normal operation.

Federal Communications Commission (FCC) RF Exposure Requirements

SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the
center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar
physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap
pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for
certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

R&TTE Compliance Statement

This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.

Safety

This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment.
All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use
of the equipment.

EU Countries Intended for Use

The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.

EU Countries Not Intended for Use

None

29

EU Declaration of Conformity

English: This equipment is in compliance with the essential requirements and other relevant provisions of

Directive 2004/108/EC, 2009/125/EC.

Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive

2004/108/EC, 2009/125/EC

Čeština: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic

2004/108/EC, 2009/125/EC.

Polski: Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi

Dyrektywą UE 2004/108/EC, 2009/125/EC.

Română: Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale

Directivei 2004/108/EC, 2009/125/EC.

Русский: Это оборудование соответствует основным требованиям и положениям Директивы

2004/108/EC, 2009/125/EC.

Magyar: Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek

(2004/108/EC, 2009/125/EC)

Türkçe: Bu cihaz 2004/108/EC, 2009/125/EC direktifleri zorunlu istekler ve diğer hükümlerle ile

uyumludur.

Українська: Обладнання відповідає вимогам і умовам директиви 2004/108/EC, 2009/125/EC.
Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc 2004/108/EC,

2009/125/EC.

Deutsch: Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2004/108/EC, 2009/125/EC.
Español: El presente equipo cumple los requisitos esenciales de la Directiva 2004/108/EC, 2009/125/EC.

Italiano: Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili della

Direttiva 2004/108/EC, 2009/125/EC.

Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van

richtlijn 2004/108/EC, 2009/125/EC.

Português: Este equipamento cumpre os requesitos essênciais da Directiva 2004/108/EC, 2009/125/EC.
Norsk: Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv

2004/108/EC, 2009/125/EC.

Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta

bestämmelser i direktiv 2004/108/EC, 2009/125/EC.

Dansk: Dette udstyr er i overensstemmelse med de væ sentligste krav og andre relevante forordninger i

direktiv 2004/108/EC, 2009/125/EC.

Suomi: Tämä laite täyttää direktiivien 2004/108/EC, 2009/125/EC oleelliset vaatimukset ja muut

asiaankuuluvat määräykset.

WEEE Directive & Product Disposal

At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.

30