EDIMAX GS-5424PLX User manual

Download

GS-5424PLX

User Manual

09-2020 / v1.0

Contents

I Product Information .............................................................................. 1

I-1 Package Content ............................................................................................ 2

I-2 Hardware Overview ...................................................................................... 2

I-3 LED Status ............................................................................................... 3

II Installation ............................................................................................ 4

II-1 Mounting the Switch ..................................................................................... 4

II-1-1 Placement Tips........................................................................................ 4

II-1-2 Rack Mounting ........................................................................................ 5

III Getting Started ..................................................................................... 7

III-1 Power ............................................................................................................ 7

III-1-1 Connecting to Power .............................................................................. 7

III-1-2 Connecting to Network ........................................................................... 8

III-1-3 Power over Ethernet (PoE) Considerations ............................................ 9

III-1-4 Starting the Web-based Configuration Utility ...................................... 10

III-1-5 Logging In .............................................................................................. 11

III-1-6 Logging Out ........................................................................................... 12

IV Web-based Switch Configuration .......................................................... 13

IV-1 Status ........................................................................................................... 13

IV-1-1 System Information .............................................................................. 13

IV-1-2 Logging Message ................................................................................... 16

IV-1-3 Port ....................................................................................................... 17

IV-1-3-1 Statistics .................................................................................. 17

IV-1-3-2 Error Disabled .......................................................................... 19

IV-1-3-3 Bandwidth Utilization ............................................................. 20

IV-1-4 Link Aggregation ................................................................................... 21

IV-1-5 MAC Address Table ............................................................................... 22

IV-2 Network ....................................................................................................... 23

IV-2-1 IP Address ............................................................................................. 23

IV-2-2 System Time ......................................................................................... 26

IV-3 Port .............................................................................................................. 28

IV-3-1 Port Setting ........................................................................................... 28

IV-3-2 Long Range Mode ................................................................................. 31

IV-3-3 Error Disable ......................................................................................... 31

IV-3-4 Link Aggregation ................................................................................... 32

IV-3-4-1 Group ....................................................................................... 32

IV-3-4-2 Port Setting .............................................................................. 35

IV-3-4-3 LACP ......................................................................................... 37

IV-3-4-4 EEE ........................................................................................... 39

IV-3-5 Jumbo Frame ........................................................................................ 40

IV-4 PoE ............................................................................................................... 41

IV-4-1 Global Setting ....................................................................................... 41

IV-4-2 Priority Setting ...................................................................................... 43

IV-4-3 Power Limit ........................................................................................... 44

IV-4-4 PoE Show .............................................................................................. 46

IV-4-5 Power Device Monitor .......................................................................... 47

IV-5 VLAN ............................................................................................................ 48

IV-5-1 VLAN ..................................................................................................... 48

IV-5-1-1 Create VLAN ............................................................................ 48

IV-5-1-2 VLAN Configuration ................................................................. 50

IV-5-1-3 Membership ............................................................................ 51

IV-5-1-4 Port Setting .............................................................................. 53

IV-5-2 Voice VLAN ........................................................................................... 56

IV-5-2-1 Property................................................................................... 56

IV-5-2-2 Voice OUI ................................................................................. 58

IV-5-3 MAC VLAN ............................................................................................ 59

IV-5-3-1 MAC Group .............................................................................. 59

IV-5-3-2 Group Binding ......................................................................... 60

IV-5-4 Surveillance VLAN ................................................................................. 62

IV-5-4-1 Property................................................................................... 62

IV-5-4-2 Surveillance OUI ...................................................................... 63

IV-6 MAC Address Table ..................................................................................... 64

IV-6-1 Dynamic Address .................................................................................. 64

IV-6-2 Static Address ....................................................................................... 65

IV-6-3 Filtering Address ................................................................................... 65

IV-7 Spanning Tree .............................................................................................. 66

IV-7-1 Property ................................................................................................ 66

IV-7-2 Port Setting ........................................................................................... 68

IV-7-3 MST Instance ........................................................................................ 70

IV-7-4 MST Port Setting ................................................................................... 71

IV-7-5 Statistics ................................................................................................ 74

IV-8 Discovery ..................................................................................................... 76

IV-8-1 LLDP ...................................................................................................... 76

IV-8-1-1 Property................................................................................... 76

IV-8-1-2 Port Setting .............................................................................. 78

IV-8-1-3 Packet View ............................................................................. 80

IV-8-1-4 Local Information .................................................................... 83

IV-8-1-5 Neighbor .................................................................................. 86

IV-8-1-6 Statistics .................................................................................. 90

IV-9 Multicast ..................................................................................................... 92

IV-9-1 General ................................................................................................. 92

IV-9-1-1 Property................................................................................... 92

IV-9-1-2 Group Address ......................................................................... 93

IV-9-1-3 Router Port .............................................................................. 95

IV-9-2 IGMP Snooping ..................................................................................... 97

IV-9-2-1 Property................................................................................... 97

IV-9-2-2 Querier .................................................................................. 100

IV-9-2-3 Statistics ................................................................................ 102

IV-9-3 MVR .................................................................................................... 104

IV-9-3-1 Property................................................................................. 104

IV-9-3-2 Port Setting ............................................................................ 105

IV-9-3-3 Group Address ....................................................................... 107

IV-10 Security ...................................................................................................... 109

IV-10-1 RADIUS ......................................................................................... 109

IV-10-2 Management Access .................................................................... 112

IV-10-2-1 Management VLAN ............................................................... 112

IV-10-2-2 Management Service ............................................................. 112

IV-10-2-3 Management ACL .................................................................. 114

IV-10-2-4 Management ACE .................................................................. 114

IV-10-3 Authentication Manager .............................................................. 119

IV-10-3-1 Property................................................................................. 119

IV-10-3-2 Port Setting ............................................................................ 124

IV-10-3-3 Sessions ................................................................................. 127

IV-10-4 Port Security ................................................................................. 129

IV-10-5 Traffic Segmentation .................................................................... 131

IV-10-6 Storm Control ............................................................................... 132

IV-10-7 DoS ............................................................................................... 134

IV-10-7-1 Property................................................................................. 135

IV-10-7-2 Port Setting ............................................................................ 137

IV-10-8 DHCP Snooping ............................................................................ 138

IV-10-8-1 Property................................................................................. 138

IV-10-8-2 Statistics ................................................................................ 140

IV-10-8-3 Option82 Property................................................................. 142

IV-10-8-4 Option82 Circuit ID ................................................................ 144

IV-10-9 IP Source Guard ............................................................................ 146

IV-10-9-1 Port Setting ............................................................................ 146

IV-10-9-2 IMPV Binding ......................................................................... 148

IV-10-9-3 Save Database ....................................................................... 150

IV-11 ACL ............................................................................................................. 151

IV-11-1 MAC ACL ....................................................................................... 151

IV-11-2 MAC ACE ...................................................................................... 152

IV-11-3 IPv4 ACL ....................................................................................... 154

IV-11-4 IPv4 ACE ....................................................................................... 155

IV-11-5 ACL Binding .................................................................................. 159

IV-12 QoS ............................................................................................................ 161

IV-12-1 General ......................................................................................... 161

IV-12-1-1 Property................................................................................. 162

IV-12-1-2 Queue Scheduling.................................................................. 165

IV-12-1-3 CoS Mapping ......................................................................... 166

IV-12-1-4 IP Precedence Mapping ......................................................... 167

IV-12-2 Rate Limit ..................................................................................... 169

IV-12-2-1 Ingress/Egress Port ................................................................ 169

IV-13 Diagnostics ................................................................................................ 172

IV-13-1 Logging ......................................................................................... 172

IV-13-1-1 Property................................................................................. 172

IV-13-1-2 Remote Server ....................................................................... 173

IV-13-2 Mirroring ...................................................................................... 174

IV-13-3 Ping .............................................................................................. 176

IV-13-4 Traceroute .................................................................................... 177

IV-13-5 Copper Test .................................................................................. 178

IV-13-6 Fiber Module ................................................................................ 179

IV-13-7 UDLD ............................................................................................ 180

IV-13-7-1 Property................................................................................. 180

IV-13-7-2 Neighbor ................................................................................ 182

IV-14 Management ............................................................................................. 183

IV-14-1 User Account ................................................................................ 183

IV-14-2 Fireware ....................................................................................... 185

IV-14-2-1 Upgrade / Backup .................................................................. 185

IV-14-2-2 Active Image .......................................................................... 189

IV-14-3 Configuration ............................................................................... 190

IV-14-3-1 Upgrade / Backup .................................................................. 190

IV-14-3-2 Save Configuration ................................................................ 194

IV-14-4 SNMP ........................................................................................... 194

IV-14-4-1 View ....................................................................................... 194

IV-14-4-2 Group ..................................................................................... 195

IV-14-4-3 Community ............................................................................ 197

IV-14-4-4 User ....................................................................................... 199

IV-14-4-5 Engine ID ............................................................................... 202

IV-14-4-6 Trap Event ............................................................................. 204

IV-14-4-7 Notification............................................................................ 204

IV-14-5 Time Range .................................................................................. 208

V Surveillance Mode ........................................................................................ 209

V-1 Home Page ............................................................................................. 209

V-1-1 Overview ................................................................................................ 210

V-1-2 Port Info ................................................................................................. 211

V-1-3 IP Camera Info ........................................................................................ 212

V-1-4 NVR Info ................................................................................................. 213

V-1-5 PoE Info .................................................................................................. 213

V-1-6 Status ..................................................................................................... 214

V-2 PoE Scheduling ....................................................................................... 215

V-3 Time ....................................................................................................... 217

V-3-1 Clock Settings ......................................................................................... 217

V-3-2 SNTP Settings ......................................................................................... 218

V-4 Surveillance Settings .............................................................................. 219

V-5 Mail Alert ............................................................................................... 223

V-6 Powered Device Monitor ........................................................................ 224

V-7 ONVIF ..................................................................................................... 226

V-7-1 IPC Discover ........................................................................................... 226

V-7-2 NVR Discover .......................................................................................... 226

V-8 E-map Management ............................................................................... 227

V-8-1 Image Upload ......................................................................................... 227

V-8-2 Image Settings ........................................................................................ 228

V-8-3 E-map View ............................................................................................ 229

V-9 Tools ...................................................................................................... 229

V-9-1 Firmware Information ............................................................................ 229

V-9-2 Firmware Upgrade & Backup .................................................................. 230

V-9-3 Configuration Restore & Backup ............................................................. 230

V-9-4 Reset ...................................................................................................... 231

V-9-5 Reboot System ....................................................................................... 231

I Product Information

The EDIMAX GS-5424PLX long-range web-smart switch comes with a web

based user interface, equipped with 24 Gigabit PoE+ ports, and SFP+ ports for

10 Gigabit uplinks and long-range copper or optical connections.

The 10 GbE connectivity fully utilizes the power of your office networking for

demanding tasks, such as data backup, video conferencing, IP surveillance,

high volume transaction processing, large file transferring, and more.

You can find all supporting documents from the link below or via QR Code:

https://www.edimax.com/download

(Once you’ve visited the Edimax official website, please enter the model no. “GS-5424PLX” into the search box to search for your product.)

I-1 Package Content

No.

Descriptions

Reset button

LED (ALM, PoE/MAX, SYS, PWR

LED (Link/Act)

CONSOLE port

PoE Ports (1~24)

SFP+ Ports (25~28)

GS-5424PLX

Power Cord

Rack-Mount Kit & Screws

GS-5424PLX

3 2 5 4 6

Before start using this product, please check if there is anything missing in the package, and contact your dealer to claim the missing item(s):

I-2 Hardware Overview

I-3 LED Status

Function

Status

Description

PWR

On (Green)

Power on

Off

Power off

Alert

On (Red)

System fault detected.

(System failure due to

overheating of switch or

wrong voltage)

Off

No faults detected

PoE/Max

On (Green)

Over PoE max power

Off

Under PoE max power

Link/ACT

(1-24 port)

On (Green)

Link at 1000M

On ( Amber )

Link at 10/100M

Blinking

Sending or receiving data

Off

Port disconnected or link fail

SFP+

(25-28 port)

On (Blue)

10G link

On (Green)

1000M link

Blinking

Data transmitting

Off

Port disconnected or link fail

PoE

On (Green)

PoE power output on

Blinking

PoE power output over 30W

Off

PoE power output off

II Installation

This chapter describes how to install and connect your Edimax Switch. Read the following topics and perform the procedures in the correct order. Incorrect installation may cause damage to the product.

II-1 Mounting the Switch

There are two ways to physically set up the switch.

 Place the switch on a flat surface. To place the switch on a desktop, install the four

rubber feet (included) on the bottom of the switch.

 Mount the switch in a standard rack (1 rack unit high).

II-1-1 Placement Tips

 Ambient Temperature — To prevent the switch from overheating, do not operate it

in an area that exceeds an ambient temperature of 122°F (50°C).

 Air Flow — Be sure that there is adequate air flow around the switch.  Mechanical Loading — Be sure that the switch is level and stable to avoid any

hazardous conditions.

 Circuit Overloading — Adding the switch to the power outlet must not overload that

circuit.

Follow these guidelines to install the switch securely.

 Put the switch in a stable place such as a desktop, to avoid it falling.  Ensure the switch works in the proper AC input range and matches the voltage

labeled.

 Ensure there is proper heat dissipation from and adequate ventilation around the

switch.

 Ensure the switch’s location can support the weight of the switch and its accessories.

Figure 4 - Desktop Installation

II-1-2 Rack Mounting

You can mount the switch in any standard size, 19-inch (about 48 cm) wide rack. The switch requires 1 rack unit (RU) of space, which is 1.75 inches (44.45 mm) high.

For stability, load the rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy rack is likely to be unstable and may tip over.

When mounting smaller switch products into a standard 19-inch rack, a pair of extension brackets (sometimes referred to as ears) are needed to adapt the switch to the rack size.

These extension brackets are mounted on the switch using the screws provided in the kit, and have two holes that are used to then screw the switch into the rack.

An example of one type of these extension brackets is shown in the following figure.

A common problem that occurs during rack mounting is the distance between the screw holes on the rack. Some racks are made with a uniform distance between all of the holes, and others have the holes organized into groups (see photo on the next page for an example).

When organized into groups, the switch must be placed in the rack so that the holes in the extension brackets line up correctly.

1. Align the mounting brackets with the mounting holes on the switch’s side panels

and secure the brackets with the screws provided.

Figure 5 - Bracket Installation

2. Secure the switch on the equipment rack with the screws provided.

Figure 6 - Rack Installation

III Getting Started

This section provides an introduction to the web-based configuration utility, and covers the following topics:

 Powering on the device  Connecting to the network  Power over Ethernet (PoE) considerations  Starting the web-based configuration utility

III-1 Power III-1-1 Connecting to Power

Power down and disconnect the power cord before servicing or wiring a switch.

Do not disconnect modules or cabling unless the power is first switched off. The device only supports the voltage outlined in the type plate. Do not use any other power components except those specifically designated for the switch. Disconnect the power cord before installation or cable wiring.

The switch is powered by the AC 100-240 V 50/60Hz internal high-performance power supply. It is recommended to connect the switch with a single-phase three-wire power source with a neutral outlet, or a multifunctional computer professional source. Connect the AC power connector on the back panel of the switch to the external power source with the included power cord, and check the power LED is on.

Figure 7 - Rear View AC Power Socket

III-1-2 Connecting to Network

To connect the switch to the network:

1. Connect an Ethernet cable to the Ethernet port of a computer

2. Connect the other end of the Ethernet cable to one of the numbered Ethernet

ports of the switch. The LED of the port lights if the device connected is active.

3. Repeat Step 1 and Step 2 for each device to connect to the switch.

We strongly recommend using CAT-5E or better cable to connect network devices. When connecting network devices, do not exceed the maximum cabling distance of 100 meters (328 feet). It can take up to one minute for attached devices or the LAN to be operational after it is connected. This is normal behavior. Connect the switch to end nodes using a standard Cat 5/5e Ethernet cable (UTP/STP) to connect the switch to end nodes as shown in the illustration below. Switch ports will automatically adjust to the characteristics (MDI/MDI-X, speed, duplex) of the device to which the switch is connected.

Figure 8 - PC Connect

III-1-3 Power over Ethernet (PoE) Considerations

Model

Power Dedicated to PoE

PoE Ports

PoE Standard Supported

GS-542PLX

400W

1 to 24

IEEE802.3at/af

For PoE switch models, consider the following information: Devices considered a Power Sourcing Equipment (PSE), can support up to 30 Watts per PoE port to a Powered Device (PD).

Ports 1-24 provide PoE power supply functionality with a maximum output power up to 30W each port. This can supply power to PDs such as internet phones, network cameras, wireless access points. Connect the switch PoE port directly to the PD port using a network cable.

When connecting switches capable of supplying PoE, consider the following information:

 Switch models with PoE function are PSEs. These models are capable of supplying DC

power to attached PDs, such as VoIP phones, IP cameras, and wireless access points (APs). PoE switches. Additionally, PoE switches are capable of detecting and supplying power to pre-standard legacy PoE Power Devices. Due to the support for legacy PoE, there is a possibility that PoE switches acting as a PSE may inadvertently detect and supply power an attached PSE, including other PoE switches. This false detection may result in a PoE switch operating improperly and unable to supply power to attached PDs.

 The prevention of a false detection can be easily remedied by disabling PoE on the

ports that are used to connect PSEs. Another simple practice to prevent a false detection is to first power up a PSE device before connecting it to a PoE switch.

 When a device is falsely detected as a PD, disconnect the device from the PoE port

and power recycle the device with AC power before reconnecting it to the PoE port.

III-1-4 Starting the Web-based Configuration Utility

This section describes how to navigate the web-based switch configuration utility. Be sure to disable any pop-up blocker.

Browser Restrictions

 If you are using older versions of Internet Explorer, you cannot directly use an IPv6

address to access the device. You can, however, use the DNS (Domain Name System) server to create a domain name that contains the IPv6 address, and then use that domain name in the address bar in place of the IPv6 address.

 If you have multiple IPv6 interfaces on your management station, use the IPv6 global

address instead of the IPv6 link local address to access the device from your browser.

Launching the Configuration Utility

To open the web-based configuration utility:

1. Open a Web browser.

2. Enter the IP address of the device you are configuring in the address bar on the

browser (factory default IP address is 192.168.2.1) and then press Enter.

When the device is using the factory default IP address, its power LED flashes continuously. When the device is using a DHCP assigned IP address or an administrator-configured static IP address, the power LED is lit a solid color. Your

computer’s IP address must be in the same subnet as the switch. For example, if the switch is using the factory default IP address, your computer’s IP address can be in the

following range: 192.168.2.x (whereas x is a number from 2 to 254). After a successful connection, the login window displays.

Figure 9 - Login Window

III-1-5 Logging In

The default username is admin and the default password is admin. The first time that you log in with the default username and password, you are required to enter a new password.

To log in to the device configuration utility:

1. Enter the default user ID (admin) and the default password (admin).

2. If this is the first time that you logged on with the default user ID (admin) and the

default password (admin) it is recommended that you change your password immediately. See “4.9.3. Administrator” for additional information.

When the login attempt is successful, the System Information window displays.

Figure 10 - System Information

If you entered an incorrect username or password, an error message appears and the Login page remains displayed on the window. If you are having problems logging in, please see the Launching the Configuration Utility section in the Administration Guide for additional information.

III-1-6 Logging Out

By default, the application logs out after ten minutes of inactivity.

To manually logout, click Logout in the top right corner of any page.

When a timeout occurs or you intentionally log out of the system, a message appears and the Login page appears, with a message indicating the logged-out state. After you log in, the application returns to the initial page.

IV Web-based Switch Configuration

No.

Name

Description

Configuration menu

Navigate to locate specific switch functions.

Configuration settings

Edit specific function settings.

Switch’s current link

status

Green squares indicate the port link is up, while black squares indicate the port link is down.

Common toolbar

Provides access to frequently used settings.

1 3

The PoE smart switch software provides rich Layer 2 functionality for switches in your networks. This chapter describes how to use the web-based management interface (Web UI) to configure the switch’s features.

For the purposes of this manual, the user interface is separated into four sections, as shown in the following figure:

Figure 11 - User Interface

IV-1 Status

Use the Status pages to view system information and status.

IV-1-1 System Information

This page shows switch panel, CPU utilization, Memory utilization and other system current information. It also allows user to edit some system information.

To display the Device Information web page, click Status > System Information.

Item

Description

Model

Model name of the switch.

System Name

System name of the switch. This name will also use as CLI prefix of each line. (“Switch>” or “Switch#”).

System Location

Location information of the switch.

System Contact

Contact information of the switch.

MAC Address

Base MAC address of the switch.

IPv4 Address

Current system IPv4 address.

System OID

SNMP system object ID.

System Uptime

Total elapsed time from booting.

Current Time

Current system time.

Loader Version

Boot loader image version.

Loader Date

Boot loader image build date.

Firmware Version

Current running firmware image version.

Firmware Date

Current running firmware image build date.

Telnet

Current Telnet service enable/disable state.

SSH

Current SSH service enable/disable state.

HTTP

Current HTTP service enable/disable state.

HTTPS

Current HTTPS service enable/disable state.

SNMP

Current SNMP service enable/disable state.

Figure 12 - Status > System Information

Click “Edit” button on the table title to edit following system information.

Figure 13 - Status > System Information > Edit System Information

Item

Description

System Name

System name of the switch. This name will also use as CLI prefix of each line. (“Switch>” or “Switch#”).

System Location

Location information of the switch.

System Contact

Contact information of the switch.

IV-1-2 Logging Message

Item

Description

Log ID

The log identifier.

Time

The time stamp for the logging message.

Severity

The severity for the logging message.

Description

The description of logging message.

Viewing

 RAM: Show the logging messages stored on the RAM.  Flash: Show the logging messages stored on the Flash.

Clear

Clear the logging messages.

Refresh

Refresh the logging messages.

To view the logging messages stored on the RAM and Flash, click Status > Logging

Message.

Figure 14 - Status > Logging Message

IV-1-3 Port

IV-1-3-1 Statistics

This page displays standard counters on network traffic form the Interfaces, Ethernet

-like and RMONMIB. Interfaces and Ethernet-like counters display errors on the traffic passing through each port. RMON counters provide a total count of different frame types

and sizes passing through each port. The “Clear” button will clear MIB counter of current

selected port.

To display the Port Flow Chart web page, click Status > Port > Statistics.

Figure 15 - Status > Port > Statistics

Item

Description

Port

Select one port to show counter statistics.

MIB Counter

Select the MIB counter to show different counter type

 All: All counters.  Interface: Interface related MIB counters.  Etherlike: Ethernet-like related MIB counters.  RMON: RMON related MIB counters.

Refresh Rate

Refresh the web page every period of seconds to get new counter of specified port.

IV-1-3-2 Error Disabled

Item

Description

□

Select one or more port to operate.

Port

Interface or port number.

Reason

Port will be disabled by one of the following error reason:

 BPDU Guard  UDLD  Self Loop  Broadcast Flood  Unknown Multicast Flood  Unicast Flood  ACL  Port Security Violation  DHCP rate limit  ARP rate limit

Time Left (sec)

The time left in second for the error recovery.

Refresh

Refresh the current page.

Recover

Recover the selected port status.

To display the Error Disabled web page, click Status > Port > Error Disabled.

Figure 16 - Status > Port > Error Disabled

IV-1-3-3 Bandwidth Utilization

Item

Description

Refresh Rate

Refresh the web page every period of seconds to get new bandwidth utilization data.

This page allow user to browse ports’ bandwidth utilization in real time. This page will

refresh automatically in every refresh period.

To display Bandwidth Utilization web page, click Status > Port > Bandwidth Utilization.

Figure 17 - Status > Port > Bandwidth Utilization

IV-1-4 Link Aggregation

Item

Description

LAG

LAG Name.

Name

LAG port description.

Type

The type of the LAG.

 Static: The group of ports assigned to a static LAG are always

active members.

 LACP: The group of ports assigned to dynamic LAG are

candidate ports. LACP determines which candidate ports are active member ports.

Link Status

LAG port link status.

Active Member

Active member ports of the LAG.

Inactive Member

Inactive member ports of the LAG.

To display the Link Aggregation web page, click Status > Link Aggregation.

Figure 18 - Status > Link Aggregation

IV-1-5 MAC Address Table

Item

Description

VLAN

VLAN ID of the mac address.

MAC Address

MAC address.

Type

The type of MAC address

 Management: DUT’s base mac address for management Purpose.  Static: Manually configured by administrator  Dynamic: Auto learned by hardware.

Port

The type of Port

 CPU: DUT’s CPU port for management purpose.  Other: Normal switch port.

The MAC address table page displays all MAC address entries on the switch including static MAC address created by administrator or auto learned from hardware. The “Clear”

button will clear all dynamic entries and “Refresh” button will retrieve latest MAC

address entries and show them on page.

To display the MAC Address Table web page, click Status > MAC Address Table.

Figure 19 - Status > MAC Address Table

IV-2 Network

Use the Network pages to configure settings for the switch network interface and how the switch connects to a remote server to get services.

IV-2-1 IP Address

This section allows you to edit the IP address, Netmask, Gateway and DNS server of the switch.

To view the IP Address menu, navigate to Network > IP Address.

Figure 20 - Network > IP Address

Item

Description

Address Type

The address type of switch IP configuration including

 Static: Static IP configured by users will be used.  Dynamic: Enable the DHCP to obtain the IP address from a

DHCP server.

IP Address

Specify the switch static IP address on the static configuration.

Subnet Mask

Specify the switch subnet mask on the static configuration.

Default Gateway

Specify the default gateway on the static configuration. The

default gateway must be in the same subnet with switch IP address configuration.

DNS Server 1

Specify the primary user-defined IPv4 DNS server configuration.

DNS Server 2

Specify the secondary user-defined IPv4 DNS server configuration.

Table 3-2: IPv6 Address fields

IPv4 Address

The operational IPv4 address of the switch.

IPv4 Gateway

The operational IPv4 gateway of the switch.

IPv6 Address v6

The operational IPv6 address of the switch.

IPv6 Gateway

The operational IPv6 gateway of the switch.

Link Local Address

The IPv6 link local address for the switch.

IV-2-2 System Time

Item

Description

Source

Select the time source.

This page allow user to set time source, static time, time zone and daylight saving settings. Time zone and daylight saving takes effect both static time or time from SNTP server.

To display System Time page, click Network > System Time.

Figure 21 - Network > System Time

 SNTP: Time sync from NTP server.  From Computer: Time set from browser host.  Manual Time: Time set by manually configure.

Time Zone

Select a time zone difference from listing district.

SNTP

Address Type

Select the address type of NTP server. This is enabled when time source is SNTP.

Server Address

Input IPv4 address or hostname for NTP server. This is enabled when time source is SNTP.

Server Port

Input NTP port for NTP server. Default is 123. This is enabled when time source is SNTP.

Manual Time

Date

Input manual date. This is enabled when time source is manual.

Time

Input manual time. This is enabled when time source is manual.

Daylight Saving Time

Type

Select the mode of daylight saving time.

 Disable: Disable daylight saving time.  Recurring: Using recurring mode of daylight saving time.  Non-Recurring: Using non-recurring mode of daylight saving

time.

 USA: Using daylight saving time in the United States that

starts on the second Sunday of March and ends on the first Sunday of November.

 European: Using daylight saving time in the Europe that

starts on the last Sunday in March and ending on the last Sunday in October.

Offset

Specify the adjust offset of daylight saving time.

Recurring From

Specify the starting time of recurring daylight saving time. This field available when selecting “Recurring” mode.

Recurring To

Specify the ending time of recurring daylight saving time. This field available when selecting “Recurring” mode.

Non-recurring From

Specify the starting time of non-recurring daylight saving time. This field available when selecting “Non-Recurring” mode.

Non-recurring To

Specify the ending time of recurring daylight saving time. This field available when selecting “Non-Recurring” mode.

Non-recurring From

Specify the starting time of non-recurring daylight saving time. This field available when selecting “Non-Recurring” mode.

Non recurring To

Specify the ending time of recurring daylight saving time. This field available when selecting “Non-Recurring” mode.

IV-3 Port

Item

Description

Port

Port Name.

Type

Port media type.

Description

Port Description.

State

Port admin state

 Enabled: Enable the port.  Disabled: Disable the port.

Link Status

Current port link status

 Up: Port is link up.  Down: Port is link down.

Speed

Current port speed configuration and link speed status.

Use the Port pages to configure settings for switch port related features.

IV-3-1 Port Setting

This page shows port current status and allow user to edit port configura-tions. Select port entry and click “Edit” button to edit port configurations.

To display Port Setting web page, click Port > Port Setting.

Figure 22 - Port > Port Setting

Duplex

Current port duplex configuration and link duplex status.

Flow Control

Current port flow control configuration and link flow control status.

Item

Description

Port

Selected Port list.

Description

Port media type.

State

Port admin state.

 Enabled: Enable the port.  Disabled: Disable the port.

Speed

Port speed capabilities.

 Auto: Auto speed with all capabilities.  Auto-10M: Auto speed with 10M ability only.  Auto-100M: Auto speed with 100M ability only.  Auto-1000M: Auto speed with 1000M ability only.  Auto-10M/100M: Auto speed with 10M/100M abilities.  10M: Force speed with 10M ability.  100M: Force speed with 100M ability.  1000M: Force speed with 1000M ability.

Duplex

Port duplex capabilities.

Click “Edit” button to edit Port Setting menu

Figure 23 - Port > Port Setting > Port Setting

 Auto: Auto duplex with all capabilities.  Half: Auto speed with 10M and 100M ability only.  Full: Auto speed with 10M/100M/1000M ability only.

Flow Control

Port flow control.

 Auto: Auto flow control by negotiation.  Enabled: Enable flow control ability.  Disabled: Disable flow control ability.

IV-3-2 Long Range Mode

This page shows port current status and Enable long range mode will double the cabling distance but reduce the speed to 10Mbps.

To display Long Range Mode web page, click Port > Long Range Mode Setting.

Figure 24 - Port > Long Range Mode

IV-3-3 Error Disable

To display Error Disabled web page, click Port > Error Disabled

Figure 25 - Port > Error disable

Item

Description

Recover Interval

Auto recovery after this interval for error disabled port.

BPDU Guard

Enabled to auto shutdown port when BPDU Guard reason occur. This reason caused by STP BPDU Guard mechanism.

UDLD

Enabled to auto shutdown port when UDLD violation occur.

Self Loop

Enabled to auto shutdown port when Self Loop reason occur.

Broadcast Flood

Enabled to auto shutdown port when Broadcast Flood reason occur. This reason caused by broadcast rate exceed broadcast storm control rate.

Unknown Multicast Flood

Enabled to auto shutdown port when Unknown Multicast Flood reason occur. This reason caused by unknown multicast rate exceed unknown multicast storm control rate.

Unicast Flood

Enabled to auto shutdown port when Unicast Flood reason occur. This reason caused by unicast rate exceed unicast storm control rate.

ACL

Enabled to auto shutdown port when ACL shutdown port reason occur. This reason caused packet match the ACL shutdown port action.

Port Security

Enabled to auto shutdown port when Port Security Violation reason occur. This reason caused by violation port security rules.

DHCP rate limit

Enabled to auto shutdown port when DHCP rate limit reason occur. This reason caused by DHCP packet rate exceed DHCP rate limit.

ARP rate limit

Enabled to auto shutdown port when ARP rate limit reason occur. This reason caused by DHCP packet rate exceed ARP rate limit.

IV-3-4 Link Aggregation

IV-3-4-1 Group

This page allow user to configure link aggregation group load balance algorithm and group member. To view the Group menu, navigate to Port > Link Aggregation > Group.

Figure 26 - Port > Link Aggregation > Group

Item

Description

Load Balance Algorithm

LAG load balance distribution algorithm

 src-dst-mac: Based on MAC address.  src-dst-mac-ip: Based on MAC address and IP address.

LAG

LAG Name.

Name

LAG port description.

Type

The type of the LAG

 Static: The group of ports assigned to a static LAG are always

active members.

 LACP: The group of ports assigned to dynamic LAG are

candidate ports. LACP determines which candidate ports are active member ports.

Link Status

LAG port link status

Active Member

Active member ports of the LAG.

Inactive Member

Inactive member ports of the LAG.

Click “Edit” to edit Link Aggregation Group menu.

Figure 27 - Port > Link Aggregation > Group > Edit Link Aggregation Group

Item

Description

LAG

Selected LAG group ID.

Name

LAG port description.

Type

The type of the LAG

 Static: The group of ports assigned to a static LAG are always

active members.

 LACP: The group of ports assigned to dynamic LAG are

candidate ports. LACP determines which candidate ports are active member ports.

Member

Select available port to be LAG group member port.

IV-3-4-2 Port Setting

Item

Description

LAG

LAG Port Name.

Type

LAG Port media type.

Description

LAG Port description.

State

LAG Port admin state

 Enabled: Enable the port.  Disabled: Disable the port.

Link Status

Current LAG port link status

 Up: Port is link up.  Down: Port is link down.

Speed

Current LAG port speed configuration and link speed status.

Duplex

Current LAG port duplex configuration and link duplex status.

Flow Control

Current LAG port flow control configuration and link flow control status.

This page shows LAG port current status and allow user to edit LAG port configurations. Select LAG entry and click “Edit” button to edit LAG port configurations.

To display LAG Port Setting web page, click Port > Link Aggregation > Port Setting.

Figure 28 - Port > Link Aggregation > Port Setting

Click “Edit” to view Edit Port Setting menu.

Item

Description

Port

Selected Port list.

Description

Port description.

State

Port admin state

 Enabled: Enable the port.  Disabled: Disable the port.

Speed

Port speed capabilities

Flow Control

Port flow control

 Auto: Auto flow control by negotiation.  Enabled: Enable flow control ability.  Disabled: Disable flow control ability.

Figure 29 - Port > Link Aggregation > Port Setting > Edit Port Setting

IV-3-4-3 LACP

Item

Description

System Priority

Configure the system priority of LACP. This decides the system priority field in LACP PDU.

Port

Port Name.

Port Priority

LACP priority value of the port.

Timeout

The periodic transmissions type of LACP PDUs.

 Long: Transmit LACP PDU with slow periodic (30s).  Short: Transmit LACPP DU with fast periodic (1s).

This page allow user to configure LACP global and port configurations. Select ports and click “Edit” button to edit port configuration.

To display the LACP Setting web page , click Port > Link Aggregation > LACP.

Figure 30 - Port > Link Aggregation > LACP

Click "Edit" button to view Edit LACP Port Setting menu.

Figure 31 - Port > Link Aggregation > LACP > Edit LACP Port Setting

Item

Description

Port

Selected port list.

Port Priority

Enter the LACP priority value of the port

Timeout

The periodic transmissions type of LACP PDUs.

 Long: Transmit LACP PDU with slow periodic (30s).  Short: Transmit LACPP DU with fast periodic (1s).

IV-3-4-4 EEE

Item

Description

Port

Port Name.

State

Port EEE admin state

 Enabled: EEE is enabled.  Disabled: EEE is disabled.

Operational Status

Port EEE operational status

 Enabled: EEE is operating.  Disabled: EEE is no operating.

This page allow user to configure Energy Efficient Ethernet settings.

To display the EEE web page, click Port > EEE.

Click “Edit” to edit the EEE menu.

Figure 32 - Port > EEE

Figure 33 - Port > EEE > Edit EEE Setting

Item

Description

Port

Port Name

State

Port EEE admin state

 Enabled: EEE is enabled.  Disabled: EEE is disabled.

Item

Description

Jumbo Frame

Enable or disable jumbo frame. When jumbo frame is enabled, switch max frame size is allowed to configure. When jumbo frame is disabled, default frame size 1522 will be used.

IV-3-5 Jumbo Frame

This page allow user to configure switch jumbo frame size.

To display Jumbo Frame web page, click Port > Jumbo Frame.

Figure 34 - Port > Jumbo Frame

IV-4 PoE

Port security can set port isolation and specific behavior.

IV-4-1 Global Setting

To display the Global web page, click PoE > Global Setting.

Figure 35 - PoE > Global Setting

Item

Description

Nominal Power

Maximum supply power.

Consuming Power

Current consumed power.

Remaining Power

Remaining available power.

Schedule Status

Schedule status global switch.

Name

PoE Schedule Name.

Port List

The ports provide power in designated schedule index.

Schedule Status

The current schedule status.

Item

Description

Index

The serial number of schedule list.

Schedule Status

 Checked: Schedule status is enabled.  Unchecked: Schedule status is disabled.

Name

Enter the PoE schedule name.

Date

Select a valid time for this schedule.

Port List

Select the port provide power.

Click “Edit” to view PoE Schedule List menu.

Figure 36 - PoE > Priority Setting > Edit PoE Schedule Edit

IV-4-2 Priority Setting

Use this section to set the power supply priority of PoE ports. Individual ports can be assigned critical, high, or low power supply priority.

To display the Priority Setting web page, click PoE > Priority Setting.

Figure 37 - PoE > Priority Setting

Click the port to change its priority status according to the bottom right hand chart.

IV-4-3 Power Limit

Item

Description

Port

Port name.

Power Limit

The max supply power for this port.

To display the Power Limit web page, click PoE > Power Limit.

Figure 38 - PoE > Power Limit

Click “Edit” to view Power Limit Setting menu.

Item

Description

Port List

Selected port list.

Power Limit

Enter max supply power value for the selected port list.

Figure 39 - PoE > Power Setting > Power Limit Setting Table

IV-4-4 PoE Show

To display the PoE Status web page, click PoE > Power Status.

Figure 40 - PoE > Power Stauts

Per Port PoE Status Checked: Port PoE status is enabled. Unchecked: Port PoE status is disabled.

IV-4-5 Power Device Monitor

This page shows the information of each ports, including mode, ping PD IP Address, interval time, retry count, action, reboot time and connect status.

To display port setting page, please click the “Edit” button.

Item

Description

Port list

Display the interface of port entry.

Status

Enable/Disable

Ping PD IP Address

Input IP address of the PD

Internal Time

The default setting about Interval (30 seconds) will make switch detect the PD status by performing ping requests every 30 seconds.

Retry Count

If there is no ping reply from the PD, retry count starts to count from 1. Once retry count is reached to 2 times, the switch will perform the action in which you defined.

Action

The Action including none, PD reboot, Reboot & Alarm and Alarm

IV-5 VLAN

A virtual local area network, virtual LAN or VLAN, is a group of hosts with a common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of their physical location. A VLAN has the same attributes as a physical local area network (LAN), but it allows for end stations to be grouped togeth-er even if they are not located on the same network switch. VLAN membership can be configured through software instead of physically relocating devices or connections.

IV-5-1 VLAN

Use the VLAN pages to configure settings of VLAN.

IV-5-1-1 Create VLAN

This page allows user to add or delete VLAN ID entries and browser all VLAN entries that add statically or dynamic learned by GVRP. Each VLAN entry has a unique name, user can edit VLAN name in edit page.

To display Create VLAN page, click VLAN > VLAN > Create VLAN.

Item

Description

Available VLAN

VLAN has not created yet. Select available VLANs from left box then move to right box to add.

Created VLAN

VLAN had been created. Select created VLANs from right box then move to left box to delete

VLAN

The VLAN ID.

Name

The VLAN Name.

Type

The VLAN Type.

 Static: Port base VLAN.  Dynamic: 802.1q VLAN.

Figure 41 - VLAN > VLAN > Create VLAN

Click “Edit” button to view Edit VLAN Name menu.

Figure 42 - VLAN > VLAN > Create VLAN > Edit VLAN Name

Item

Description

Name

Input VLAN name.

Item

Description

VLAN

Select specified VLAN ID to configure VLAN configuration.

Port

Display the interface of port entry.

IV-5-1-2 VLAN Configuration

This page allow user to configure the membership for each port of selected VLAN.

To display VLAN Configuration page, click VLAN > VLAN > VLAN Configuration.

Figure 43 - VLAN > VLAN > VLAN Configuration

Mode

Display the interface VLAN mode of port.

Membership

Select the membership for this port of the specified VLAN ID.

 Forbidden: Specify the port is forbidden in the VLAN.  Excluded: Specify the port is excluded in the VLAN.  Tagged: Specify the port is tagged member in the VLAN.  Untagged: Specify the port is untagged member in the VLAN.

PVID

Display if it is PVID of interface.

IV-5-1-3 Membership

This page allow user to view membership information for each port and edit membership for specified interface.

To display Membership page, click VLAN > VLAN > Membership.

Figure 44 - VLAN > VLAN > Membership

Item

Description

Port

Display the interface of port entry.

Mode

Display the interface VLAN mode of port.

Administrative VLAN

Display the administrative VLAN list of this port.

Operational VLAN

Display the operational VLAN list of this port. Operational VLAN means the VLAN status that really runs in device. It may different to administrative VLAN.

Click "Edit" button to view the Edit Port Setting menu

Item

Description

Port

Display the interface.

Mode

Display the VLAN mode of interface.

Membership

Select VLANs of left box and select one of following membership then move to right box to add membership. Select VLANs of right box then move to left box to remove membership. Tagging membership may not choose in differ VLAN port mode. Select the time source.

 Forbidden: Set VLAN as forbidden VLAN.  Excluded: This option is always disabled.  Tagged: Set VLAN as tagged VLAN.  Untagged: Set VLAN as untagged VLAN.  PVID: Check this checkbox to select the VLAN ID to be the port-based

VLAN ID for this port. PVID may auto select or can’t select in differ

settings.

Figure 45 - VLAN > VLAN > Membership > Edit Port Setting

IV-5-1-4 Port Setting

This page allow user to configure ports VLAN settings such as VLAN port mode, PVID etc…The attributes depend on different VLAN port mode.

To display Port Setting page, click VLAN > VLAN > Port Setting.

Figure 46 - VLAN > VLAN > Port Setting

Item

Description

Port

Display the interface.

Mode

Display the VLAN mode of interface.

PVID

Display the Port-based VLAN ID of port.

Accept Frame Type

Display accept frame type of port.

Ingress Filtering

Display ingress filter status of port.

Uplink

Display uplink status.

TPID

Display TPID used of interface.

Click “Edit” button to Edit Port Setting menu.

Item

Description

Port

Display selected port to be edited.

Mode

Select the VLAN mode of the interface.

 Forbidden: Set VLAN as forbidden VLAN.  Hybrid: Support all functions as defined in IEEE 802.1Q specification.  Access: Accepts only untagged frames and join an untagged VLAN.  Trunk: An untagged member of one VLAN at most, and is a tagged

member of zero or more VLANs.

PVID

Specify the port-based VLAN ID (1-4094). It’s only available with Hybrid and Trunk mode.

Accepted Type

Specify the acceptable-frame-type of the specified interfaces. It’s only available with Hybrid mode.

Ingress Filtering

Set checkbox to enable/disable ingress filtering. It’s only available with

Hybrid mode.

Uplink

Set checkbox to enable/disable uplink mode. It’s only available with trunk

mode.

TPID

Select TPID used of interface. It’s only available with trunk mode.

Figure 47 - VLAN > VLAN > Port Setting > Edit Port Setting

IV-5-2 Voice VLAN

Use the Voice VLAN pages to configure settings of Voice VLAN.

IV-5-2-1 Property

This page allow user to configure global and per interface settings of voice VLAN.

To display Property Web page, click VLAN> Voice VLAN> Property.

Figure 48 - VLAN > Voice VLAN > Property

Item

Description

State

Set checkbox to enable or disable voice VLAN function.

VLAN

Select Voice VLAN ID. Voice VLAN ID cannot be default VLAN.

Cos/802.1p

Select a value of VPT. Qualified packets will use this VPT value as inner priority.

Remarking

Set checkbox to enable or disable 1p remarking. If enabled, qualified packets will be remark by this value.

Aging Time

Input value of aging time. Default is 1440 minutes. A voice VLAN entry will be age out after this time if without any packet pass through.

Port Setting Table

Port

Display port entry.

State

Display enable/disabled status of interface.

Mode

Display voice VLAN mode.

QoS Policy

Display voice VLAN remark will effect which kind of packet.

Item

Description

Port

Display selected port to be edited.

State

Set checkbox to enable/disabled voice VLAN function of interface.

Mode

Select port voice VLAN mode

 Auto: Voice VLAN auto detect packets that match OUI table and add

received port into voice VLAN ID tagged member.

 Manual: User need add interface to VLAN ID tagged member

manually.

QoS Policy

Select port QoS Policy mode

 Voice Packet: QoS attributes are applied to packets with OUIs in the

source MAC address.

 All: QoS attributes are applied to packets that are classified to Voice

VLAN.

Click “Edit” button to view Edit Port Setting menu.

Figure 49 - VLAN > Voice VLAN > Property > Edit Port Setting

IV-5-2-2 Voice OUI

Item

Description

OUI

Display OUI MAC address.

Description

Display description of OUI entry.

This page allow user to add, edit or delete OUI MAC addresses. Default has 8 pre-defined OUI MAC.

To display the Voice OUI Web page, click VLAN > Voice VLAN > Voice OUI.

Figure 50 - VLAN > Voice VLAN > Voice OUI

Click “Add” or “Edit” button to Add/Edit Voice OUI menu.

Figure 51 - VLAN > Voice VLAN > Voice OUI > Add/Edit Voice OUI

Item

Description

OUI

Input OUI MAC address. Can’t be edited in edit dialog.

Description

Input description of the specified MAC address to the voice VLAN OUI table.

Item

Description

Group ID

Display group ID of entry.

MAC Address

Display mac address of entry.

Mask

Display mask of mac address for classified packet.

IV-5-3 MAC VLAN

Use the MAC VLAN pages to configure settings of MAC VLAN.

IV-5-3-1 MAC Group

This page allow user to add or edit groups settings of MAC VLAN.

To display the MAC page , click VLAN > MAC VLAN > MAC Group.

Figure 52 - VLAN > MAC VLAN > MAC Group

Click “Add” button or "Edit" button to view Add/Edit MAC menu.

Figure 53 - VLAN > MAC VLAN > MAC Group > Add/Edit MAC

Item

Description

Group ID

Input group ID that is a unique ID of mac group entry. The range from 1 to 2147483647. Only available on Add Dialog.

MAC Address

Input mac address for classifying packets.

Mask

Input mask of mac address.

IV-5-3-2 Group Binding

This page allow user to bind MAC VLAN group to each port with VLAN ID.

To display Group Binding page, click VLAN> MAC VLAN > Group Binding.

Figure 54 - VLAN > MAC VLAN > Group Binding

Item

Description

Port

Display port ID that binding with MAC group entry.

Group ID

Display group ID that port binding with.

VLAN

Display VLAN ID that assign to packets which match MAC group.

Item

Description

Port

Select ports in left box then move to right to binding with MAC group. Or select ports in right box then move to left to unbind with MAC group. Only interface has hybrid VLAN mode can be selected and bound with protocol group. Only available on Add dialog.

Group ID

Select a Group ID to associate with port. Only available on Add dialog.

VLAN

Input VLAN ID that will assign to packets which match MAC group.

Click “Add” or “Edit” button to view the Add/Edit Group Binding menu.

Figure 55 - VLAN > MAC VLAN > Add/Edit Group Binding

IV-5-4 Surveillance VLAN

Use the Surveillance VLAN pages to configure settings of Surveillance VLAN.

IV-5-4-1 Property

Item

Description

State

Enable/Disable

VLAN

Choose none or indicate VLAN

CoS/802.1p Remarking

The 802.1p standard defines seven levels of CoS from 0 through to 7 (highest priority). 802.1p is a sub-set of the 802.1q standard which added additional fields into the header of a standard Ethernet frame allowing it to contain VLAN identifiers as well as the priority values.

Port Aging Time

When aging is configured on an interface that's using port security, all the dynamically learned secure addresses age out when the aging time expire

Item

Description

Port

Display port entry.

State

Display enable/disabled status of interface.

Mode

Display voice VLAN mode.

QoS Policy

Display voice VLAN remark will effect which kind of packet.

To display Port Setting page, click the “Edit” button.

IV-5-4-2 Surveillance OUI

Item

Description

OUI

An organizationally unique identifier (OUI) is a 24-bit number that uniquely identifies a vendor, manufacturer, or other

organization. ... In MAC addresses, the OUI is combined with a

24-bit number (assigned by the assignee of the OUI) to form the address.

OUI Mask

Specifies a set of MAC addresses using a bit mask to indicate the bits of the MAC addresses that must fit to the specified MAC address attribute.

To change the description of your IP camera, click the “Edit” button.

IV-6 MAC Address Table

Use the MAC Address Table pages to show dynamic MAC table and configure settings for static MAC entries.

IV-6-1 Dynamic Address

To display the Dynamic Address web page, click MAC Address Table > Dynamic Address.

Figure 56 - MAC Address Table > Dynamic Address

Item

Description

Aging Time

The time in seconds that an entry remains in the MAC address table. Its valid range is from 10 to 630 seconds, and the default value is 300 seconds.

Item

Description

MAC Address

The MAC address to which packets will be statically forwarded.

VLAN

Specify the VLAN to show or clear MAC entries.

Port

Interface or port number.

Item

Description

MAC Address

Specify unicast MAC address in the packets to be dropped.

VLAN

Specify the VLAN to show or clear MAC entries.

IV-6-2 Static Address

To display the Static Address web page, click MAC Address Table > Static Address.

Figure 57 - MAC Address Table > Static Address.

IV-6-3 Filtering Address

To display the Filtering Address web page, click MAC Address Table > Filtering Address.

Figure 58 - MAC Address Table > Filtering Address.

IV-7 Spanning Tree

The Spanning Tree Protocol (STP) is a network protocol that ensures a loop-free topology for any bridged Ethernet local area network.

IV-7-1 Property

To display the Property web page, click Spanning Tree > Property.

Figure 59 - Spanning Tree > Property

Item

Description

State

Enable/disable the STP on the switch.

Operation Mode

Specify the STP operation mode.

 STP: Enable the Spanning Tree (STP) operation.  RSTP: Enable the Rapid Spanning Tree (RSTP) operation.  MSTP: Enable the Multiple Spanning Tree (MSTP) operation.

Path Cost

Specify the path cost method.

 Long: Specifies that the default port path costs are within the

range: 1-200,000,000.

 Short: Specifies that the default port path costs are within the

range: 1-65,535.

BPDU Handling

Specify the BPDU forward method when the STP is disabled.

 Filtering: Filter the BPDU when STP is disabled.  Flooding: Flood the BPDU when STP is disabled.

Priority

Specify the bridge priority. The valid range is from 0 to 61440, and the value should be the multiple of 4096. It ensures the probability that the switch is selected as the root bridge, and the lower value has the higher priority for the switch to be selected as the root bridge of the topology.

Hello Time

Specify the STP hello time in second to broadcast its hello message to other bridges by Designated Ports. Its valid range is from 1 to 10 seconds.

Max Age

Specify the time interval in seconds for a switch to wait the configuration messages, without attempting to redefine its own configuration.

Forward Delay

Specify the STP forward delay time, which is the amount of time that a port remains in the Listening and Learning states before it enters the Forwarding state. Its valid range is from 4 to 10 seconds.

TX Hold Count

Specify the tx-hold-count used to limit the maximum numbers of packets transmission per second. The valid range is from 1 to 10.

Region Name

The MSTP instance name. Its maximum length is 32 characters. The default value is the MAC address of the switch.

Revision

The MSTP revision number. Its valid rage is from 0 to 65535.

Max Hop

Specify the number of hops in an MSTP region before the BPDU is discarded. The valid range is 1 to 40.

Operational Status

Bridge Identifier

Bridge identifier of the switch.

Designated Root Identifier

Bridge identifier of the designated root bridge. Root Port

Operational root port of the switch.

Root Path Cost

Operational root path cost.

Topology Change Count

Numbers of the topology changes.

Last Topology Change

The last time for the topology change.

Item

Description

Port

Specify the interface ID or the list of interface IDs.

State

The operational state on the specified port.

Path Cost

STP path cost on the specified port.

Priority

STP priority on the specified port.

BPDU Filter

The states of BPDU filter on the specified port.

BPDU Guard

The states of BPDU guard on the specified port.

Operational Edge

The operational edge port status on the specified port.

Operational Point-to-Point

The operational point-to-point status on the specified port.

Port Role

The current port role on the specified port. The possible values are:

“Disabled”, “Master”, “Root”, “Designated”, “Alternative”, and “Backup”.

Port State

The current port state on the specified port. The possible values are: “Disabled”, “Discarding”, “Learning”, and “Forwarding”.

Designated Bridge

The bridge ID of the designated bridge.

Designated Port ID

The designated port ID on the switch. Designated Cost

The path cost of the designated port on the switch.

IV-7-2 Port Setting

To configure and display the STP port settings, click STP > Port Setting.

Figure 60 - Spanning Tree > Port Setting

Protocol Migration Check

Restart the Spanning Tree Protocol (STP) migration process (re-negotiate with its neighborhood) on the specific interface.

Item

Description

Port

Selected port ID.

State

Enable/Disable the STP on the specified port.

Path Cost

Specify the STP path cost on the specified port.

Priority

Specify the STP path cost on the specified port.

Edge Port

Specify the edge mode.

 Enable: Force to true state (as link to a host).  Disable: Force to false state (as link to a bridge).

In the edge mode, the interface would be put into the Forwarding state immediately upon link up. If the edge mode is enabled for the interface and there are BPDUs received on the interface, the loop might be occurred in the short time before

Click "Edit" button to view Edit Port Setting menu.

Figure 61 - Spanning Tree > Port Setting > Edit Port Setting

the STP state change.

BPDU Filter

The BPDU Filter configuration avoids receiving / transmitting BPDU from the specified ports.

 Enable: Enable BPDU filter function.  Disable: Disable BPDU filter function.

BPDU Guard

The BPDU Guard configuration to drop the received BPDU directly.

 Enable: Enable BPDU guard function.  Disable: Disable BPDU guard function.

Point-to-Point

Specify the Point-to-Point port configuration:

 Auto: The state is depended on the duplex setting of the port  Enable: Force to true state.  Disable: Force to false state

Item

Description

MSTI

Designated port number.

Priority

The bridge priority on the specified MSTI.

IV-7-3 MST Instance

To configure MST instance setting, click STP > MST Instance.

Figure 62 - Spanning Tree > MST Instance

Bridge Identifier

The bridge identifier on the specified MSTI.

Designated Root Bridge

The designated root bridge identifier on the specified MSTI.

Root Port

The designated root port on the specified MSTI.

Root Path Cost

The designated root path cost on the specified MSTI.

Remaining Hop

The configuration of remaining hop on the specified MSTI.

VLAN

The VLAN configuration on the specified MSTI.

Item

Description

VLAN

Select the VLAN list for the specified MSTI.

Priority

Specify the bridge priority on the specified MSTI. The valid range is from 0 to 61440, and the value must be the multiple of 4096. It ensures the probability that the switch is selected as the root bridge, and the lower values has the higher priority for the switch to be selected as the root bridge of the STP topology.

Click "Edit" button to view Edit MST Instance menu.

Figure 63 - Spanning Tree > MST Instance > Edit MST Instance Setting

IV-7-4 MST Port Setting

To configure and display MST port setting, click STP > MST Port Setting.

Item

Description

MSTI

Specify the port setting on the specified MSTI.

Port

Specify the interface ID or the list of interface IDs.

Path Cost

The port path cost on the specified MSTI.

Priority

The port priority on the specified MSTI.

Port Role

The current port role on the specified port. The possible values are:

“Disabled”, “Master”, “Root”, “Designated”, “Alternative”, and “Backup”.

Port State

The current port state on the specified port. The possible values are: “Disabled”, “Discarding”, “Learning”, and “Forwarding”.

Mode

The operational STP mode on the specified port.

Type

The possible value for the port type are:

 Boundary: The port attaching an MST Bridge to a LAN that is not in

the same region.

 Internal: The port attaching an MST Bridge to a LAN that is not in

the same region.

Designated Bridge

The bridge ID of the designated bridge.

Figure 64 - Spanning Tree > MST Port Setting

Designated Port ID

The designated port ID on the switch. Designated Cost

The path cost of the designated port on the switch.

Remaining Hop

The remaining hops count on the specified port.

Item

Description

Path Cost

Specify the STP port path cost on the specified MSTI.

Priority

Specify the STP port priority on the specified MSTI.

Click "Edit" button to view Edit MST Port Setting menu.

Figure 65 - Spanning Tree > MST Port Setting > Edit MST Port Setting

IV-7-5 Statistics

Item

Description

Refresh Rate

The option to refresh the statistics automatically.

Receive BPDU (Config)

The counts of the received CONFIG BPDU.

Receive BPDU (TCN)

The counts of the received TCN BPDU.

Receive BPDU (MSTP)

The counts of the received MSTP BPDU.

Transmit BPDU (Config)

The counts of the transmitted CONFIG BPDU.

Transmit BPDU (TCN)

The counts of the transmitted TCN BPDU.

Transmit BPDU (MSTP)

The counts of the transmitted MSTP BPDU.

Clear

Clear the statistics for the selected interfaces

View

View the statistics for the interface.

To display the STP statistics, click STP > Statistics.

Figure 66 - Spanning Tree > Statistics

Click "View" button to view the STP Port Statistic menu.

Item

Description

Refresh Rate

The option to refresh the statistics automatically.

Clear

Clear the statistics for the selected interfaces.

Figure 67 - Spanning Tree > Statistics > STP Port Statistic

IV-8 Discovery

Item

Description

State

Enable/ Disable LLDP protocol on this switch.

LLDP Handling

Select LLDP PDU handling action to be filtered, bridging or flooded when LLDP is globally disabled.

 Filtering: Deletes the packet.  Bridging: (VLAN-aware flooding) Forwards the packet to all VLAN

members.

 Flooding: Forwards the packet to all ports

TLV Advertise

Select the interval at which frames are transmitted. The default is 30

Use this section to configure LLDP.

IV-8-1 LLDP

LLDP is a one-way protocol; there are no request/response sequences. Informa-tion is advertised by stations implementing the transmit function, and is received and processed by stations implementing the receive function. The LLDP category contains LLDP and LLDP-MED pages.

IV-8-1-1 Property

To display LLDP Property Setting web page, click Discovery > LLDP > Property.

Figure 68 - Discovery > LLDP > Property

Interval

seconds, and the valid range is 5–32767 seconds.

Holdtime Multiplier

Select the multiplier on the transmit interval to assign to TTL (range 2–10, default = 4).

Reinitialization Delay

Select the delay before a re-initialization (range 1–10 seconds, default = 2).

Transmit Delay

Select the delay after an LLDP frame is sent (range 1–8191 seconds, default = 3).

Fast Start Repeat Count

Select fast start repeat count when port link up (range 1–10, default =

3).

IV-8-1-2 Port Setting

Item

Description

Port

Port Name.

Mode

The port LLDP mode.

Selectde TLV

The Selected LLDP TLV.

To display LLDP Port Setting, click Discovery > LLDP > Port Setting.

Figure 69 - Discovery > LLDP > Port Setting

Click "Edit" button to view Edit Port Setting menu.

Item

Description

Port

Select specified port or all ports to configure LLDP state.

Mode

Select the transmission state of LLDP port interface.

 Disable: Disable the transmission of LLDP PDUs.  RX Only: Receive LLDP PDUs only.  TX Only: Transmit LLDP PDUs only.  TX And RX: Transmit and receive LLDP PDUs both.

Optional TLV

Select the LLDP optional TLVs to be carried (multiple selection is allowed).

 System Name  Port Description  System Description  System Capability  802.3 MAC-PHY  802.3 Link Aggregation  802.3 Maximum Frame Size  Management Address  802.1 PVID.

Figure 70 - Discovery > LLDP > Port Setting > Edit Port Setting

802.1 VLAN Name

Select the VLAN Name ID to be carried (multiple selection is allowed).

IV-8-1-3 Packet View

To display LLDP Overloading, click Discovery > LLDP > Packet View.

Figure 71 - Discovery > LLDP > Packet View

Item

Description

Port

Port Name.

In-Use (Bytes)

Total number of bytes of LLDP information in each packet.

Available (Bytes)

Total number of available bytes left for additional LLDP information in each packet.

Operational Status

Overloading or not.

Click "Detail" button to view Packet View Detail menu.

Item

Description

Port

Port Name.

Mandatory TLVs

Total mandatory TLV byte size. Status is sent or overloading.

MED Capabilities

Total MED Capabilities TLV byte size. Status is sent or overloading.

MED Location

Total MED Location byte size. Status is sent or overloading.

MED Network Policy

Total MED Network Policy byte size. Status is sent or overloading.

MED Inventory

Total MED Inventory byte size. Status is sent or overloading

MED Extended Power via MDI

Total MED Extended Power via MDI byte size. Status is sent or overloading.

802.3 TLVs

Total 802.3 TLVs byte size. Status is sent or overloading.

Optional TLVs

Total Optional TLV byte size. Status is sent or overloading.

802.1 TLVs

Total 802.1 TLVs byte size. Status is sent or overloading.

Total

Total number of bytes of LLDP information in each packet.

Figure 72 - Discovery > LLDP > Packet View > Packet View Detail

IV-8-1-4 Local Information

Use the LLDP Local Information to view LLDP local device information.

To display LLDP Local Device, click Discovery > LLDP > Local Information.

Item

Description

Chassis ID Subtype

Type of chassis ID, such as the MAC address.

Chassis ID

Identifier of chassis. Where the chassis ID subtype is a MAC address, the MAC address of the switch is displayed.

System Name

Name of switch.

System Description

Description of the switch. Capabilities

Primary functions of the device, such as Bridge, WLAN AP, or Router.

Figure 73 - Discovery > LLDP > Local Information

Supported

Capabilities Enabled

Primary enabled functions of the device. Port ID Subtype

Type of the port identifier that is shown.

LLDP Status

LLDP Tx and Rx abilities.

LLDP Med Status

LLDP MED enable state.

Click “Detail” button on the page to view detail information of the selected port.

Figure 74 - Discovery > LLDP > Local Information > Detail

IV-8-1-5 Neighbor

Use the LLDP Neighbor page to view LLDP neighbors information.

To display LLDP Remote Device, click Discovery > LLDP > Neighbor.

Figure 75 - Discovery > LLDP > Neighbor

Item

Description

Local Port

Number of the local port to which the neighbor is connected.

Chassis ID Subtype

Type of chassis ID (for example, MAC address).

Port ID Subtype

Type of the port identifier that is shown.

Port ID

Identifier of port.

System Name

Published name of the switch.

Time to Live

Time interval in seconds after which the information for this neighbor is deleted.

Click “detail” to view selected neighbor detail information

Figure 76 LLDP Neighbor Detail Page

IV-8-1-6 Statistics

The Link Layer Discovery Protocol (LLDP) Statistics page displays summary and per-port information for LLDP frames transmitted and received on the switch. To display LLDP Statistics status, click Discovery > LLDP > Statistics.

Figure 77 - Discovery > LLDP > Statistics

Item

Description

Insertions

The number of times the complete set of information advertised by a particular MAC Service Access Point (MSAP) has been inserted into tables associated with the remote systems.

Deletions

The number of times the complete set of information advertised by MSAP has been deleted from tables associated with the remote systems.

Drops

The number of times the complete set of information advertised by MSAP could not be entered into tables associated with the remote systems because of insufficient resources.

Age Outs

The number of times the complete set of information advertised by MSAP has been deleted from tables associated with the remote systems because the information timeliness interval has expired.

Statistics Table

Port

Interface or port number.

Transmit Frame Total

Number of LLDP frames transmitted on the corresponding port.

Receive Frame Total

Number of LLDP frames received by this LLDP agent on the corresponding port, while the LLDP agent is enabled.

Receive Frame Discard

Number of LLDP frames discarded for any reason by the LLDP agent on the corresponding port.

Receive Frame Error

Number of invalid LLDP frames received by the LLDP agent on the corresponding port, while the LLDP agent is enabled.

Receive TLV Discard

Number of TLVs of LLDP frames discarded for any reason by the LLDP agent on the corresponding port.

Receive TLV Unrecognized

Number of TLVs of LLDP frames that are unrecognied while the LLDP agent is enabled.

Neighbor Timeout

Number of age out LLDP frames.

IV-9 Multicast

Item

Description

Unknown Multicast Action

Set the unknown multicast action

 Flood: flood the unknown multicast data.  Drop: drop the unknown multicast data.  Router port: forward the unknown multicast data to router

port.

IPv4

Set the ipv4 multicast forward method.

 MAC-VID: forward method dmac+vid.  DIP-VID: forward method dip+vid.

IPv6

 MAC-  DIP-VID: forward method dip+vid(dip is ipv6 low 32 bit).

Use this section to configure Multicast.

IV-9-1 General

Use the General pages to configure settings of IGMP and MLD common function.

IV-9-1-1 Property

To display multicast general property Setting web page, click Multicast> General> Property.

Figure 78 - Multicast > General > Property

IV-9-1-2 Group Address

Item

Description

IP Version

 IPv4: ipv4 multicast group  IPv6: ipv6 multicast group

VLAN

The VLAN ID of group.

Group Address

The group IP address.

Member

The member ports of group.

Type

The type of group. Static or Dynamic.

Life(Sec)

The life time of this dynamic group.

This page allow user to browse all multicast groups that dynamic learned or statically added.

To display Multicast General Group web page, click Multicast> General > Group Address.

Figure 79 - Multicast > General > Group Address

Click “Add” or “Edit” button to view Add or Edit Group Address menu.

Item

Description

VLAN

The VLAN ID of group.

IP Version

 IPv4: ipv4 multicast group  IPv6: ipv6 multicast group

Group Address

The group IP address.

Member

The member ports of group.

Figure 80 - Multicast > General > Group Address > Add/Edit Group Address

EDIMAX GS-5424PLX User manual

Specifications and Main Features

Frequently Asked Questions

User Manual