How it Works
Edimax
Loading...
GS-5416PLC
operation manual
221 pgs6.18 Mb0
Service Manual
4 pgs550.22 Kb0
Service Manual [de]
4 pgs753.4 Kb0

Edimax GS-5416PLC operation manual

GS-5416PLC / GS-5424PLC
User Manual
04-2018 / v1.0
CONTENTS
I Introduction .......................................................................................... 1
I-4-1 Ports ........................................................................................................ 2
I-4-2 LED Indicators ......................................................................................... 3
II Installation ............................................................................................ 4
II-1-1 Placement Tips........................................................................................ 4
II-1-2 Desktop Mounting .................................................................................. 5
II-1-3 Rack Mounting ........................................................................................ 5
III Getting Started ..................................................................................... 7
III-4-1 Logging In .............................................................................................. 12
III-4-2 Logging Out ........................................................................................... 13
IV Web-based Switch Configuration .......................................................... 14
IV-1-1 System Information .............................................................................. 15
IV-1-2 Logging Message ................................................................................... 17
IV-1-3 Port ....................................................................................................... 18
IV-1-4 Link Aggregation ................................................................................... 23
IV-1-5 MAC Address Table ............................................................................... 24
IV-2-1 IP Address ............................................................................................. 25
IV-2-2 System Time ......................................................................................... 28
IV-3-1 Port Setting ........................................................................................... 30
IV-3-2 Long Range Mode ................................................................................. 33
IV-3-3 Error Disable ......................................................................................... 34
IV-3-4 Link Aggregation ................................................................................... 35
IV-3-5 Jumbo Frame ........................................................................................ 42
IV-4-1 Global Setting ....................................................................................... 43
IV-4-2 Priority Setting ...................................................................................... 45
IV-4-3 Power Limit ........................................................................................... 46
IV-4-4 PoE Status ............................................................................................. 48
IV-4-5 PD (Powered Device) Alive Check ......................................................... 49
IV-5-1 VLAN ..................................................................................................... 51
IV-5-2 Voice VLAN ........................................................................................... 59
IV-5-3 MAC VLAN ............................................................................................ 62
IV-6-1 Dynamic Address .................................................................................. 65
IV-6-2 Static Address ....................................................................................... 65
IV-6-3 Filtering Address ................................................................................... 66
IV-7-1 Property ................................................................................................ 67
IV-7-2 Port Setting ........................................................................................... 69
IV-7-3 MST Instance ........................................................................................ 71
IV-7-4 MST Port Setting ................................................................................... 73
IV-7-5 Statistics ................................................................................................ 75
IV-8-1 LLDP ...................................................................................................... 77
IV-9-1 General ................................................................................................. 94
IV-9-2 IGMP Snooping ..................................................................................... 99
IV-9-3 MVR .................................................................................................... 106
IV-10-1 RADIUS ......................................................................................... 111
IV-10-2 Management Access .................................................................... 114
IV-10-3 Authentication Manager .............................................................. 120
IV-10-4 Port Security ................................................................................. 130
IV-10-5 Protected Port .............................................................................. 132
IV-10-6 Storm Control ............................................................................... 134
IV-10-7 DoS ............................................................................................... 136
IV-10-8 DHCP Snooping ............................................................................ 140
IV-10-9 IP Source Guard ............................................................................ 148
IV-11-1 MAC ACL ....................................................................................... 153
IV-11-2 MAC ACE ...................................................................................... 154
IV-11-3 IPv4 ACL ....................................................................................... 156
IV-11-4 IPv4 ACE ....................................................................................... 157
IV-11-5 ACL Binding .................................................................................. 161
IV-12-1 General ......................................................................................... 163
IV-12-2 Rate Limit ..................................................................................... 171
IV-13-1 Logging ......................................................................................... 174
IV-13-2 Mirroring ...................................................................................... 176
IV-13-3 Ping .............................................................................................. 178
IV-13-4 Traceroute .................................................................................... 179
IV-13-5 Copper Test .................................................................................. 180
IV-13-6 Fiber Module ................................................................................ 181
IV-13-7 UDLD ............................................................................................ 182
IV-14-1 User Account ................................................................................ 185
IV-14-2 Fireware ....................................................................................... 187
IV-14-3 Configuration ............................................................................... 191
IV-14-4 SNMP ........................................................................................... 195
I Introduction
or
1
2
3
1. GS-5416PLC Switch
OR
GS-5424PLC Switch
2. Power Cord
3. Rack-Mount Kit & Screws
Thank you for choosing a Edimax (PoE) WEB Smart Ethernet Switch. This device is designed to be operational right out-of-the-box as a standard bridge. In the default configuration, it will forward packets between connecting devices after powered up.
Before you begin installing the switch, make sure you have all of the package contents available, and a PC with a web browser for using web-based system management tools.
I-1 Overview
The Edimax GS-54XXPLC Series Smart Switch features 4 RJ45 and 4 SFP Combo ports. The GS-5416PLC and GS-5424PLC come with 16 and 24 Gigabit PoE+ ports respectively.
I-2 Package Content
Before using the product, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.
1
I-3 Features
No.
Name
Description
1
10/100/1000Mbps RJ-45 ports
1-24 for GS-5424PLC 1-16 for GS-5416PLC
Designed to connect to network devices with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. Each has a corresponding 10/100/1000Mbps LED.
2
RJ45/SFP combo Ports (SFP1, SFP2, SFP3, and SFP4)
Designed to install SFP modules or RJ-45 connect to network devices with a bandwidth of 1000Mbps. Each has a corresponding 1000Mbps LED.
1
2
1
2
Supports up to 24 10/100/1000Mbps Gigabit Ethernet ports and 4 SFP slots or 4
mini-GBIC/SFP slots
IEEE 802.3af/at PoE compliant to simplify deployment and installation GS-5416PLC supports PoE up to 30W per port with 330W total power budget.
Available PoE power output budget is 280W
GS-5424PLC supports PoE up to 30W per port with 450W total power budget.
Available PoE power output budget is 400W
Automatically detects powered devices (PD) and power consumption levels IEEE 802.1Q VLAN for network segmentation to enhance performance and security Supports Access Control List (ACL) Switch capacity: PG28CB: 56Gbps, Forwarding rate: 41.6Mbps Supports IGMP Snooping V1 / V2 / V3 8K MAC address table and 10K jumbo frames 19-inch rack-mountable metal case
I-4 Product Components I-4-1 Ports
The following are the front views of the switches.
Figure 1 – GS-5424PLC Front View
Figure 2 – GS-5416PLC Front View
2
The following is the rear view of the switches:
No.
Name
Description
1
AC power in
Support AC100 – 240V 50-60Hz.
No.
Name
Description
1
Power
Off: power off On: power on
2
System
Off: system not ready On: system ready Blinking: system boot-up
3
PoE LED
Off: PoE inactive On: PoE active
4
Port LED
Off: port disconnected or link fail Green on: 1000Mbs connected Amber on: 10/100Mbs connected Blinking: sending or receiving data
5
Combo Port LED
Off: port disconnected or link fail Green on: 1000Mbs connected
1 1 5 5 2 3 1
2 3 4
4
Figure 3 - Rear View
I-4-2 LED Indicators
The following are the front views of the switches.
Figure 4 – GS-5424PLC Front View LED Indicators
Figure 5 – GS-5416PLC Front View LED Indicators
3
II Installation
This chapter describes how to install and connect your Edimax Switch. Read the following topics and perform the procedures in the correct order. Incorrect installation may cause damage to the product.
Please note, since the installation / mounting instructions for different models of switches are almost identical, GS-5424PLC is used as the graphical demonstrations here.
II-1 Mounting the Switch
There are two ways to physically set up the switch.
Place the switch on a flat surface. Mount the switch in a standard rack (1 rack unit high).
II-1-1 Placement Tips
Ambient Temperature — To prevent the switch from overheating, do not operate it
in an area that exceeds an ambient temperature of 122°F (50°C).
Air Flow — Be sure that there is adequate air flow around the switch. Mechanical Loading — Be sure that the switch is level and stable to avoid any
hazardous conditions.
Circuit Overloading — Adding the switch to the power outlet must not overload that
circuit.
Follow these guidelines to install the switch securely.
Put the switch in a stable place such as a desktop, to avoid it falling. Ensure the switch works in the proper AC input range and matches the voltage
labeled.
Ensure there is proper heat dissipation from and adequate ventilation around the
switch.
Ensure the switch’s location can support the weight of the switch and its accessories.
4
II-1-2 Desktop Mounting
Please install the four rubber feet (included) on the bottom of the switch and place the switch at the desired location.
Figure 6 - Desktop Installation
II-1-3 Rack Mounting
You can mount the switch in any standard size, 19-inch (about 48 cm) wide rack. The switch requires 1 rack unit (RU) of space, which is 1.75 inches (44.45 mm) high.
For stability, load the rack from the bottom to the top, with the heaviest devices on the bottom. A top-heavy rack is likely to be unstable and may tip over.
When mounting smaller switch products into a standard 19-inch rack, a pair of extension brackets (sometimes referred to as ears) are needed to adapt the switch to the rack size.
These extension brackets are mounted on the switch using the screws provided in the kit, and have two holes that are used to then screw the switch into the rack.
An example of one type of these extension brackets is shown in the following figure.
A common problem that occurs during rack mounting is the distance between the screw holes on the rack. Some racks are made with a uniform distance between all of the holes, and others have the holes organized into groups (see photo on the next page for an example).
When organized into groups, the switch must be placed in the rack so that the holes in the extension brackets line up correctly.
5
1. Align the mounting brackets with the mounting holes on the switch’s side panels
and secure the brackets with the screws provided.
Figure 7 - Rack Mounting – Bracket Installation
2. Secure the switch on the equipment rack with the screws provided.
Figure 8 - Rack Mounting – Rack Installation
6
III Getting Started
This section provides an introduction to the web-based configuration utility, and covers the following topics:
Powering on the device Connecting to the network Power over Ethernet (PoE) considerations Starting the web-based configuration utility
III-1 Connecting to Power
Power down and disconnect the power cord before servicing or wiring a switch.
Do not disconnect modules or cabling unless the power is first switched off. The device only supports the voltage outlined in the type plate. Do not use any other power components except those specifically designated for the switch. Disconnect the power cord before installation or cable wiring.
The switch is powered by the AC 100-240 V 50/60Hz internal high-performance power supply. It is recommended to connect the switch with a single-phase three-wire power source with a neutral outlet, or a multifunctional computer professional source. Connect the AC power connector on the back panel of the switch to the external power source with the included power cord, and check the power LED is on.
Figure 9 - Rear View AC Power Socket
7
III-2 Connecting to Network
To connect the switch to the network:
1. Connect an Ethernet cable to the Ethernet port of a computer
2. Connect the other end of the Ethernet cable to one of the numbered Ethernet
ports of the switch. The LED of the port lights if the device connected is active.
3. Repeat Step 1 and Step 2 for each device to connect to the switch.
We strongly recommend using CAT-5E or better cable to connect network devices. When connecting network devices, do not exceed the maximum cabling distance of 100 meters (328 feet). It can take up to one minute for attached devices or the LAN to be operational after it is connected. This is normal behavior. Connect the switch to end nodes using a standard Cat 5/5e Ethernet cable (UTP/STP) to connect the switch to end nodes as shown in the illustration below. Switch ports will automatically adjust to the characteristics (MDI/MDI-X, speed, duplex) of the device to which the switch is connected.
Figure 10 - PC Connect
8
III-3 Power over Ethernet (PoE) Considerations
Model
Power Dedicated to PoE
PoE Ports
PoE Standard Supported
GS-5416PLC
280W
1 to 16
IEEE802.3at/af
GS-5424PLC
400W
1 to 24
IEEE802.3at/af
Devices considered a Power Sourcing Equipment (PSE), can support up to 30 Watts per PoE port to a Powered Device (PD).
Ports 1-16 of GS-5416PLC and ports 1-24 of GS-5424PLC provide PoE power supply functionality with a maximum output power up to 30W each port. This can supply power to PDs such as internet phones, network cameras, wireless access points. Connect the switch PoE port directly to the PD port using a network cable.
When connecting switches capable of supplying PoE, consider the following information:
Switch models with PoE function are PSEs. These models are capable of supplying DC
power to attached PDs, such as VoIP phones, IP cameras, and wireless access points (APs). PoE switches. Additionally, PoE switches are capable of detecting and supplying power to pre-standard legacy PoE Power Devices. Due to the support for legacy PoE, there is a possibility that PoE switches acting as a PSE may inadvertently detect and supply power an attached PSE, including other PoE switches. This false detection may result in a PoE switch operating improperly and unable to supply power to attached PDs.
The prevention of a false detection can be easily remedied by disabling PoE on the
ports that are used to connect PSEs. Another simple practice to prevent a false detection is to first power up a PSE device before connecting it to a PoE switch.
When a device is falsely detected as a PD, disconnect the device from the PoE port
and power recycle the device with AC power before reconnecting it to the PoE port.
9
III-4 Starting the Web-based Configuration Utility
This section describes how to navigate the web-based switch configuration utility. Be sure to disable any pop-up blocker.
Browser Restrictions
If you are using older versions of Internet Explorer, you cannot directly use an IPv6
address to access the device. You can, however, use the DNS (Domain Name System) server to create a domain name that contains the IPv6 address, and then use that domain name in the address bar in place of the IPv6 address.
If you have multiple IPv6 interfaces on your management station, use the IPv6 global
address instead of the IPv6 link local address to access the device from your browser.
Launching the Configuration Utility
To open the web-based configuration utility:
1. Open a Web browser.
2. Enter the IP address of the device you are configuring in the address bar on the
browser (factory default IP address is 192.168.2.1) and then press Enter.
When the device is using the factory default IP address, its power LED flashes continuously. When the device is using a DHCP assigned IP address or an administrator-configured static IP address, the power LED is lit a solid color. Your
computer’s IP address must be in the same subnet as the switch. For example, if the switch is using the factory default IP address, your computer’s IP address can be in the
following range: 192.168.2.x (whereas x is a number from 2 to 254). After a successful connection, the login window displays.
Figure 11 - GS-5416PLC Login Window
10
Figure 12 - GS-5416PLC Login Window
Please note that, unless otherwise specified, pictures / interfaces of GS-5424PLC will be used hereafter in the document.
11
III-4-1 Logging In
Note: Unless otherwise specified, pictures / interfaces of GS-5424PLC will be used hereafter in the document.
The default username is admin and the default password is 1234. The first time that you log in with the default username and password, you are required to enter a new password.
To log in to the device configuration utility:
1. Enter the default user ID (admin) and the default password (1234).
2. If this is the first time that you logged on with the default user ID (admin) and the
default password (1234) it is recommended that you change your password immediately. See IV-14 Management on page 185 for additional information.
When the login attempt is successful, the System Information window displays.
Figure 13 - System Information
12
If you entered an incorrect username or password, an error message appears and the Login page remains displayed on the window. If you are having problems logging in, please see the Launching the Configuration Utility section in the Administration Guide for additional information.
III-4-2 Logging Out
By default, the application logs out after ten minutes of inactivity.
To manually logout, click Logout in the top right corner of any page.
When a timeout occurs or you intentionally log out of the system, a message appears and the Login page appears, with a message indicating the logged-out state. After you log in, the application returns to the initial page.
13
IV Web-based Switch Configuration
No.
Name
Description
1
Configuration menu
Navigate to locate specific switch functions.
2
Configuration settings
Edit specific function settings.
3
Switch’s current link
status
Green squares indicate the port link is up, while black squares indicate the port link is down.
4
Common toolbar
Provides access to frequently used settings.
2
1 3
4
The PoE smart switch software provides rich Layer 2 functionality for switches in your networks. This chapter describes how to use the web-based management interface (Web UI) to configure the switch’s features.
For the purposes of this manual, the user interface is separated into four sections, as shown in the following figure:
Figure 14 - User Interface
14
IV-1 Status
Item
Description
Model
Model name of the switch.
System Name
System name of the switch. This name will also use as CLI prefix of each line. (“Switch>” or “Switch#”).
System Location
Location information of the switch.
System Contact
Contact information of the switch.
MAC Address
Base MAC address of the switch.
IPv4 Address
Current system IPv4 address.
Use the Status pages to view system information and status.
IV-1-1 System Information
This page shows switch panel, CPU utilization, Memory utilization and other system current information. It also allows user to edit some system information.
To display the Device Information web page, click Status > System Information.
Figure 15 - Status > System Information
15
System OID
SNMP system object ID.
System Uptime
Total elapsed time from booting.
Current Time
Current system time.
Loader Version
Boot loader image version.
Loader Date
Boot loader image build date.
Firmware Version
Current running firmware image version.
Firmware Date
Current running firmware image build date.
Telnet
Current Telnet service enable/disable state.
SSH
Current SSH service enable/disable state.
HTTP
Current HTTP service enable/disable state.
HTTPS
Current HTTPS service enable/disable state.
SNMP
Current SNMP service enable/disable state.
Item
Description
System Name
System name of the switch. This name will also use as CLI prefix of each line. (“Switch>” or “Switch#”).
System Location
Location information of the switch.
System Contact
Contact information of the switch.
Click “Edit” button on the table title to edit following system information.
Figure 16 - Status > System Information > Edit System Information
16
IV-1-2 Logging Message
Item
Description
Log ID
The log identifier.
Time
The time stamp for the logging message.
Severity
The severity for the logging message.
Description
The description of logging message.
Viewing
RAM: Show the logging messages stored on the RAM. Flash: Show the logging messages stored on the Flash.
Clear
Clear the logging messages.
Refresh
Refresh the logging messages.
To view the logging messages stored on the RAM and Flash, click Status > Logging
Message.
Figure 17 - Status > Logging Message
17
IV-1-3 Port
IV-1-3-1 Statistics
This page displays standard counters on network traffic form the Interfaces, Ethernet
-like and RMONMIB. Interfaces and Ethernet-like counters display errors on the traffic passing through each port. RMON counters provide a total count of different frame types
and sizes passing through each port. The “Clear” button will clear MIB counter of current
selected port.
To display the Port Flow Chart web page, click Status > Port > Statistics.
18
19 20
Figure 18 - Status > Port > Statistics
Item
Description
Port
Select one port to show counter statistics.
MIB Counter
Select the MIB counter to show different counter type
All: All counters. Interface: Interface related MIB counters. Etherlike: Ethernet-like related MIB counters. RMON: RMON related MIB counters.
Refresh Rate
Refresh the web page every period of seconds to get new counter of specified port.
IV-1-3-2 Error Disabled
Item
Description
□
Select one or more port to operate.
Port
Interface or port number.
Reason
Port will be disabled by one of the following error reason:
BPDU Guard UDLD Self Loop Broadcast Flood Unknown Multicast Flood Unicast Flood ACL
To display the Error Disabled web page, click Status > Port > Error Disabled.
Figure 19 - Status > Port > Error Disabled
21
Port Security Violation DHCP rate limit ARP rate limit
Time Left (sec)
The time left in second for the error recovery.
Refresh
Refresh the current page.
Recover
Recover the selected port status.
Item
Description
Refresh Rate
Refresh the web page every period of seconds to get new bandwidth utilization data.
IV-1-3-3 Bandwidth Utilization
This page allows user to browse ports’ bandwidth utilization in real time. This page will refresh automatically in every refresh period.
To display Bandwidth Utilization web page, click Status > Port > Bandwidth Utilization.
Figure 20 - Status > Port > Bandwidth Utilization
22
IV-1-4 Link Aggregation
Item
Description
LAG
LAG Name.
Name
LAG port description.
Type
The type of the LAG.
Static: The group of ports assigned to a static LAG are always
active members.
LACP: The group of ports assigned to dynamic LAG are
candidate ports. LACP determines which candidate ports are active member ports.
Link Status
LAG port link status.
Active Member
Active member ports of the LAG.
Inactive Member
Inactive member ports of the LAG.
To display the Link Aggregation web page, click Status > Link Aggregation.
Figure 21 - Status > Link Aggregation
23
IV-1-5 MAC Address Table
Item
Description
VLAN
VLAN ID of the mac address.
MAC Address
MAC address.
Type
The type of MAC address
Management: DUT’s base mac address for management Purpose. Static: Manually configured by administrator Dynamic: Auto learned by hardware.
Port
The type of Port
CPU: DUT’s CPU port for management purpose. Other: Normal switch port.
The MAC address table page displays all MAC address entries on the switch including
static MAC address created by administrator or auto learned from hardware. The “Clear” button will clear all dynamic entries and “Refresh” button will retrieve latest MAC
address entries and show them on page.
To display the MAC Address Table web page, click Status > MAC Address Table.
Figure 22 - Status > MAC Address Table
24
IV-2 Network
Use the Network pages to configure settings for the switch network interface and how the switch connects to a remote server to get services.
IV-2-1 IP Address
This section allows you to edit the IP address, Netmask, Gateway and DNS server of the switch.
To view the IP Address menu, navigate to Network > IP Address.
25
Figure 23 - Network > IP Address
Item
Description
Address Type
The address type of switch IP configuration including
Static: Static IP configured by users will be used. Dynamic: Enable the DHCP to obtain the IP address from a
DHCP server.
IP Address
Specify the switch static IP address on the static configuration.
Subnet Mask
Specify the switch subnet mask on the static configuration.
Default Gateway
Specify the default gateway on the static configuration. The
26
Loading...
+ 191 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use