Edimax GS-1008P V2 Service Manual
8-Port Gigabit PoE + Switch with DIP Switch
GS-1008P V2
802.3af
15.4W
802.3at
30W
100M/
1000M
PoE
Distance
200M
Fan-
Less
VLAN
QoS
8-Port Gigabit PoE+ Switch with DIP Switch
Introduction
The Edimax GS-1008P V2 is a Eight PoE+ Port Gigabit switch designed for use in home, small or medium sized
network environments. With 8 DIP switches, the PoE port can be manually set for ON-OFF control to extend
the PoE delivery distance up to 200 meters and also support port-based NO-OFF for VLAN and QoS functions. It
easily connects and supplies power to PoE-enabled devices such as wireless access points, network cameras
and IP phones as well as other Ethernet-enabled devices such as computers, printers and network attached
storage (NAS). The device's compact size and fan-less design make it an ideal solution for expanding home and
small business networks.
Power over Ethernet (PoE+) Auto Detection
The GS-1008P V2 features four IEEE 802.3at Power over
Ethernet (PoE+) ports which supply up to 30 watts of
electricity per port. It can convert standard 100‐240V AC
power into low‐voltage 50 - 57V DC electricity to power
IEEE 802.3at compliant network accessories via existing
LAN cables. With PoE detection capability, the GS-1008P
V2 is able to verify whether the connected device is IEEE
802.3at compliant. In the event that a PoE device is not
detected, only network data will be transmitted through
the LAN cable – meaning easy setup and management of
network devices such as access points and network
cameras.
*IP Phone: 3- 7W, IP Camera: 7- 10W PZT Camera: 15 -25+ W
*Access Point: 8W for 802.11a/g radios; upwards of 20W for 802.11n radios
The guidelines are meant to provide general estimates for power consumption. Actual power requirements vary and should
be confirmed for each model when determining your PoE budget requirements.
1
1
www.edimax.com
Power and Data Transmit Distance
DIP Switch
Status
Description
1
On
PoE Ports 1 – 2 Power + Data extend
PoE Extend
Off
As a normal PoE switch
2
On
PoE Ports 3 – 4 Power + Data extend
PoE Extend
Off
As a normal PoE switch
3
On
Ports 1 – 4 VLAN enabled
VLAN
Off
Ports 1 – 4 VLAN disabled
4
On
QoS (Video & Voice Traffic High Priority) enabled
QoS
Off
QoS disabled
5
On
PoE Ports 5 Power + Data extend
PoE Extend
Off
As a normal PoE switch
6
On
PoE Ports 6 Power + Data extend
PoE Extend
Off
As a normal PoE switch
7
On
PoE Ports 7 Power + Data extend
PoE Extend
Off
As a normal PoE switch
8
On
Ports 5 – 7 VLAN enabled
VLAN
Off
Ports 5 – 7 VLAN disabled
Extension
The built-in solid DIP switch provides “Extend”
operation modes on switch 1 & 2. The GS-1008P
V2 operates as a “Standard” IEEE 802.at/af PoE
Switch when DIP switches status off. In the
“Extend” mode, status on, the GS-1008P V2
operates on a per-port basis at 10Mbps duplex
operation but can support 30-watt PoE power
output over a distance of up to 200 meters
overcoming the 100m limit on Ethernet UTP
cable. With this brand-new feature, the GS1008P V2 provides an additional solution for
802.3at/af PoE distance extension, thus saving
the cost of Ethernet cable installation.
8-Port Gigabit PoE+ Switch with DIP Switch
GS-1008P V2
Innovative Port-based VLAN
features
The ES-1008P V2 features portbased VLAN where ports can be
isolated from each other via DIP
switch port 3 & 8. This can help to
prevent IP camera’s multicast or
broadcast storms from affecting
each other.
Hardware QoS for Video & Voice Traffic Priority
Supports 802.1p QoS via DIP switch port 4. This ensures first
priority for video and voice traffic.
2
www.edimax.com
Loading...