Edimax ET-913, ET-913MSC, ET-913SSC1, ET-913SSC2, ET-913SSC3 User Manual

Introduction

Congratulations on purchasing Edimax’s ET-913 Series
Media Converter. The ET-913 series convert the signals
between two different transmission medium, allowing user
a simple and cost-effective method to migrate between
UTP cable and fiber optic cable.

FCC Warning

The ET-913 Series Media Converters have been tested
and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These
standards are designed to provide reasonable protection
against harmful interference when these devices are
operated in a commercial environment. These devices
generate, use, and can radiate radio frequency energy
and may cause harmful interference to radio
communications unless installed in accordance with this
User’s Guide. Operation of these devices in a residential
area is likely to cause harmful interference which will
make the user responsible for the appropriate remedial
action at his / her own expense.

CE Mark Warning

These are Class B products. In a domestic environment
these products may cause radio interference in which case
the user will need to consider adequate preventative
methods.

1. Checklist

The carton should contain the following items:

- ET-913 Series Media Converter

- AC-DC Power Adapter

- User’s guide

Please notify your sales representative immediately if any
items are missing or damaged.

2. Overview

ET-913 Series Media Converter is designed to meet the
massive needs for Gigabit network deployment and able to
extend a copper based Gigabit network via fiber cable to a
maximum distance up to 60KM.

ET-913 Series Media Converter is fully compliant with
IEEE802.3z & 802.3ab standards. It can be installed into a
ET-910MCR Media Converter Rack Chassis. The
installation & operation procedures are simple &
straightforward. Operation status can be locally monitored
through a set of Diagnostic LED located in the front panel.

Features

- 1000Base-T to 1000BASE-SX/LX Converter

- Standard : IEEE 802.3z & 802.3ab

- Interface: 1 * RJ-45 connector
1 * SC Duplex connector or
1 * SC Simplex connector (W2 type)

- MDI/MDIX Auto-Crossover supported

- LED: Power , FDX , TP Link, FO Link ,

TP ACT, FO ACT

- Plug-and-Play installation

- Support Link Alarm

- Support Jumbo Frame (64-9216 Byte)

- Support Voltage Monitor

3. Installation

• Attach fiber cable from the ET-913 Series Media
Converter to the fiber network. The fiber connections
must be matched – transmit socket to receive socket.

• Attach a UTP cable from the 1000BASE-T network to
the RJ-45 port on the ET-913 Series Media Converter .

• Connect the power adapter to the ET-913 Series
Media Converter and check that the Power LED lights
up. The TX Link and FX Link LEDs will light up when all
the cable connections are satisfactory.

• Dip-switch select :

Default set OFF from PIN 1 to PIN 4

Pin 1 Off/On Always OFF -

Pin 2 Off/On Always OFF ­Pin 3 Off/On FX Force Mode FX Auto-Negotiation

Pin 4 Off/On Link Alarm Disabl e Link Alarm Enable

Link

ACT

FO TP

FDX PWR

5VDC IN

TX RX

Link

ACT

FO TP

Fig. 1 ET-913 Series Media Converter Front Panel

Fig. 2 ET-913 Series Media Converter Front Panel

Fig. 3 ET-913 Series Media Converter Rear Panel

FDX PWR

ON
OFF

4. LED Description

5. Technical Specifications

Standards : IEEE 802.3z, 802.3ab

Interface: 1 X RJ45 connector

1 X SC Duplex connector or
1 X SC Simplex connector (W2)
Operation LED: Power, FDX,
TP Link, FO Link, TP ACT, FO ACT
Power: I/P AC 100-240V

O/P DC 5V, 1.6A

Power Consumption:

5W

Weight: 300g (Net Weight)

Dimensions: 26 X 71 X 97 mm

Temperature : Operating: 0 ~ 50

o

C

Storage: -20 ~ 60 oC

Humidity:

5% ~ 90% RH

Emission:

Electrical: UL, CSA

EMI: FCC Class A, CE

Media

TP EIA/TIA-568 Cat 5, 100M
Fiber 50/125, 62.5/125um multimode fiber
9/125, 10/125um single-mode fiber

Ordering Information,

Multi-mode

ET-913MSC: SC/850nm/550m

Single-mode

ET-913SSC1: SC/1310nm/10Km
ET-913SSC2: SC/1310nm/20Km
ET-913SSC3: SC/1310nm/30Km
ET-913SSC6: SC/1550nm DFB/60Km

Media Converter-G

1000Base-T To 1000Base-SX/LX

Media Converter

ET- 913 Series

ET-913MSC
ET-913SSC1
ET-913SSC2
ET-913SSC3
ET-913SSC6

User’s Guide

V 1.0

LED Color Function

PWR Green Lit when power is available
TP/Link Green Lit when TP cable connection with

remote device is good

FO/Link Green

Lit when Fiber cable connection

with remote device is good
TP ACT Green Lit when TP is activity
FO ACT Green Lit when Fiber is activity
FDX Green Lit when TP port Full Duplex M ode is

enabled

Media Converter-G