Page 1
5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
ES-5104PH V2
802.3af
15.4W
802.3at
30W
10M/
100M
PoE
Distance
200M
Fan-
Less
VLAN
QoS
5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
Introduction
The Edimax ES-5104PH V2 is a five port Fast Ethernet switch with four PoE+ Ports designed for use in home,
small or medium sized network environments. With four DIP switches, PoE ports can be manually set with
on/off control, extending PoE delivery distance up to 200 meters and port-based on/off control for VLAN and
QoS is also supported. The switch easily connects and supplies power to PoE-enabled devices such as wireless
access points, network cameras and IP phones as well as other Ethernet-enabled devices such as computers,
printers or network attached storage (NAS). The compact size and fan-less design make the switch an ideal
solution for expanding home and small business networks.
Power over Ethernet (PoE+) Auto Detection
Features four IEEE 802.3at Power over Ethernet (PoE+)
ports which supply up to 30 watts of electricity per port.
It can convert standard 100‐240V AC power into
low‐voltage 50 - 57V DC electricity to power IEEE 802.3at
compliant network accessories via existing LAN cables.
With PoE detection capability, the ES-5104PH V2 is able
to verify whether the connected device is IEEE 802.3at
compliant. In the event that a PoE device is not detected,
only network data will be transmitted through the LAN
cable – meaning easy setup and management of network
devices such as access points and network cameras.
*IP Phone: 3 - 7W, IP Camera: 7 - 10W PZT Camera: 15 - 25+ W
*Access Point: 8W for 802.11a/g radios; upwards of 20W for 802.11n radios
The guidelines are meant to provide general estimates for power consumption. Actual power requirements vary and should
be confirmed for each model when determining your PoE budget requirements.
1
1
www.edimax.com
Page 2
PoE Ports 1 – 2 Power + Data extend
As a normal PoE switch
PoE Ports 3 – 4 Power + Data extend
As a normal PoE switch
Ports 1 – 4 VLAN enabled
Ports 1 – 4 VLAN disabled
QoS (Video & Voice Traffic High Priority) enabled
QoS disabled
Power and Data Distance Extension
The built-in DIP switch provides extended
operation modes on switch 1 & 2. The ES-
5104PH V2 operates as a “standard” IEEE
802.at/af PoE Switch when DIP switches are off.
With switches on, the ES-5104PH V2 operates on
a per-port basis at 10Mbps duplex operation but
can support 30-watt PoE power output over a
distance of up to 200 meters, overcoming the
100m limit on Ethernet UTP cables. With this
brand-new feature, the ES-5104PH V2 provides
an additional solution for 802.3at/af PoE
distance extension and saves costs of Ethernet
cable installation.
5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
ES-5104PH V2
DIP Switch Status Description
On
Off
On
Off
On
Off
On
Off
DIP Switch
1. PoE Extend
2. PoE Extend
3. VLAN
4. QoS
1
PoE Extend
2
PoE Extend
3
VLAN
4
QoS
Innovative Port-based VLAN Features
The ES-5104PH V2 features port-based VLAN where ports can be isolated from each other via DIP switch port 3.
This can help to prevent IP camera’s multicast or broadcast storms from affecting each other.
Port Isolated
Port-based VLAN
Hardware QoS for Video & Voice Traffic
Priority
Supports 802.1p QoS via DIP switch port 4. This
ensures first priority for video and voice traffic.
2
High Priority
Media Streaming
VoIP
Web Browsing
Email & Downloading
Data Transfer
Low Priority
www.edimax.com
Page 3
5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
ES-5104PH V2
CCTV Mode
The unique CCTV-mode DIP switch function is ideal for surveillance networking environment. Switching all DIP
switches to on enables CCTV mode which gives multi-function PoE + data extension, Port Isolation and QoS on
the ES-5104PH V2. When using video surveillance systems for homes, business or institutions, the CCTV mode
provides better speeds for multicast viewing and easier installation. Setting all DIP switches back to off quickly
changes the ES-5104PH V2 back to normal for general-use data transmission..
One Uplink Port
The ES-5104PH V2 comes with one uplink port with 100Mbps transfer rate to ensure high-speed data and video
transmission, and reliable assurance for connections between surveillance systems and the outside network
where the four PoE+ ports can be used to their full potential.
Plug & Play, No Installation Required
Just plug Ethernet or PoE enabled devices into the switch. Data and power can be transmitted through existing
standard Cat-5e Ethernet cables with no additional cables or configuration required. The ES-5104PH V2 reduces
the difficulty, time and cost of network setup.
Flexible Network Deployment & Energy Efficient
A fast and effective solution when power outlets are unavailable for your network devices. The switch
additionally supports IEEE 802.3az Energy Efficient Ethernet which allows for less power consumption and
reduced costs during periods of low data activity.
Fan-Less Quiet & Compact Design
A fan-less design ensures quiet operation and enables an even more compact design, keeping valuable desk
space free in home or small office environments.
FEATURES
• Five 10/100Mbps Fast Ethernet ports and four PoE+ ports
• IEEE 802.3af/at PoE compliant (ports 1 - 4) for simplified deployment and installation
• Up to 30W per PoE port (total power budget: 71.5W) for powering PoE-enabled devices
• Auto-detection of powered devices (PD) and power consumption levels
• 60-watt PoE budget
• Hardware DIP switch for “Standard” and “Extend” mode selection; the “Extend” mode features 30-watt
PoE transmit distance of 200m at speed of 10Mbps
• Port-based VLAN and Loop Protection features
• Supports 802.1p Quality of Service (QoS)
• Plug & play, no installation required
• Fanless quiet operation
• External power adapter included
3
www.edimax.com
Page 4
5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
Hardware
Ports
5 RJ-45 10/100Base-T ports
4 RJ-45 10/100Base-T PoE+ ports
Transmission Method
Store and forward
LED Indicators
Power: Green LED
LNK/ACT: Green LED (Port 1 – Port 5)
PoE: Green LED (Port 1 – Port 4)
PoE Alert: Green LED (PoE overload alarm)
Fan
Fanless
DIP Switch
PoE Extend, VLAN, QoS
Power Requirements
AC-to-DC external power adapter
Input: 100-240V AC
Output: 55V DC/1.3A (Total Power: 71.5W)
Power Consumption
3W
Dimensions (L x W x H)
121*75*26mm
Weight
240.5g
Performance
Switching Capacity
1G
MAC Address
1K
Buffer Memory
56Kb
Filtering/Forwarding Rates
100Mbps port - 148,800pps
10Mbps port - 14,880pps
Power over Ethernet
Standard
IEEE 802.3af, IEEE 802.3at
Power Output
Up to 30W per port
Pin Assignment
1/2(+), 3/6(-)
PoE Power Budget
60W
Environment
Temperature
Operating: 0 ~ 40 °C
Storage: -40 ~ 70 °C
Humidity (Non-condensing)
Operating: 10 ~ 90%
Storage: 5 ~ 90%
Standards Compliance
Standards
IEEE 802.3 10BaseT Ethernet
IEEE 802.3u 100BaseTX Fast Ethernet
IEEE 802.3af Power over Ethernet (PoE)
IEEE 802.3at Power over Ethernet Plus (PoE+)
IEEE 802.3x Full-duplex and flow control
IEEE 802.3az Energy efficient Ethernet
Certifications
FCC, CE, LVD
ES-5104PH V2
HARDWARE INTERFACE
PoE Overload
Alarm LED
SPECIFICATIONS
Link/Activity (LNK/Act) LEDs PoE LEDs
PoE LED
Fast Ethernet
PoE+ Ports
Power DC Jack
Fast Ethernet
Ports
ES-5104PH V2 5-Port Fast Ethernet Switch with 4 PoE+ Ports & DIP Switch
Power On/Off
DIP Switch
1. PoE Extend
2. PoE Extend
3. VLAN
4. QoS
Edimax Technology Co., Ltd
No. 278, Xinhu 1st Rd., Neihu Dist.,
Taipei City, Taiwan
Email: sales@edimax.com.tw
*Maximum performance, actual data rates, and coverage will vary depending on network conditions and environmental
factors. Product specifications and design are subject to change without notice.
Copyright © 2017 Edimax Technology Co. Ltd. All rights reserved.
Edimax Technology Europe B.V.
Fijenhof 2, 5652 AE Eindhoven,
The Netherlands
Email: sales@edimax.nl
Edimax Computer Company
3350 Scott Blvd., Bldg.15 Santa Clara,
CA 95054, USA
Email : sales@edimax.com
www.edimax.com
Loading...