Page 1
Digital voice recorders
of EM Tiny+, Tiny16+, Tiny S+ series
Short operation manual
Purpose
Voice recorders of the Edic-mini Tiny(16)+, Tiny S+ series are professional devices
intended for making high quality record of voice messages into built-in flash memory. The
recordings can be further uploaded onto the PC. These voice recorders feature really
unique characteristics (the world's smallest size, maximum autonomy, high acoustic
sensitivity etc). The recorders are marketed as personal means of documenting audio
information providing protection against fake records as well as unauthorized access
to records. Recorders designed for home use by mass consumers.
The EMPlus program located in the built-in memory is used to operate the recorder.
SoundProcessor program is designed to process the transferred records and to
facilitate the conversion of records to text. The programs operate under Windows XP
(SP2, SP3) / Vista / 7 / 8.
Page 2
2
Model Power supply
Dimensions, mm
Weight, g
Tiny+ A77
Li-Pol 105mA/h rech.batt
29x15x12
7
Tiny+ A81
Li-Pol 500 150mA/h rech.batt
78x13x13
19
Tiny+ A83
Li-Pol 800 mA/h rech.batt
38x18,5x23,5
26
Tiny+ B70
LR43 battery
37x15x7
7
Tiny+ B73
LR43 battery
46x14x6
6
Tiny+ B74
CR2016 battery
56x26x4
10
Tiny+ B76
CR2016 battery
37x25x6
16
Tiny+ B80
CR2450 battery
48х32х7
16
Tiny+ E71
External, 3.5-6V
46x14x6
7
Tiny16+ A75
Li-Pol 150mA/h rech.batt
77x27x4
13
Tiny16+ A78
Rech.batt
41x29x8
9
Tiny16+ A79
Rech.batt
53x73x17
112
Tiny16+ A82
Li-Pol 500 150mA/h rech.batt
90х13х13
21
Tiny16+ E72
External, 3.5-6V
46x14x6
7
Tiny16+ S78
Li-Pol 150mA/h
rech.batt; solar battery
41x29x8
9
Tiny S+ E84
External, 3.5-6V
46х14х6
7
* take into account that the autonomy specified is for 8kHz/8 bit mode, when sample rate
or capacity is higher autonomy is lower (for 16kHz/16 bit roughly twice for models with
rechargeable batteries, four times for models with batteries).
It is not advisable to use 22kHz/16 bit record mode for recorders with batteries. The autonomy
also depends on the battery quality.
Page 3
3
Autonomy*,
h
Signal-to-
noise, dB
Sensitivity,
m
Sample rate, kHz
Frequency band, Hz
55
65
12
8; 11;16;22
100-10000
210
65
12
8; 11;16;22
100-10000
200
65
12
8; 11;16;22
100-10000
10
65
12
8; 11;16;22
100-10000
10
65
12
8; 11;16;22
100-10000
25
65
12
8; 11;16;22
100-10000
25
65
12
8; 11;16;22
100-10000
190
65
12
8; 11;16;22
100-10000
65
12
8; 11;16;22
100-10000
70
80
15
8; 10;13,3;20
100-10000
70
80
15
8; 10;13,3;20
100-10000
1680
80
15
8;10;13,3;20
100-10000
140
80
15
8;10;13,3;20
100-10000
80
15
8; 10;13,3;20
100-10000
74 80
15
8; 10;13,3;20
100-10000
65
12
8; 11; 16; 22;
Mono & Stereo
100-10000
Record time in 8kHz/uLaw mode – 300h (600h; 1200h; 2400h - depending on model index:
300HQ, 600HQ, 1200HQ, 2400HQ)
Interface: USB 2.0
Operating temperature range: 0…+50°C
Operation life: 3 years
Page 4
4
Main features
• Voice Activating System (VAS)
• Timers: Once and Daily
• Linear and circular recording
• Built-in clock, calendar
• Password protection of the records
• Built-in digital markers provides protection from modification of records
• Control and indication: switch and LED
In box
• Digital recorder,
• USB-adapter,
• 1 battery (for models with battery),
• device for battery removing (B76 model),
• operation manual,
Operating the recorder
For recorders with battery first set the battery in the recorder. LED will flash three
times and then will light for 40 seconds. After LED extinction the recorder is ready for
operation.
For model B70. Insert a battery into a special compartment. Set the switch to On
position for 2 seconds and then to Off position. The led flashes 3 times and then will
be active for 40 seconds. After the led turns off, the recorder is ready for operation.
Page 5
5
Attention: When installing batteries, observe the polarity (see marking on the recorder's
case). Inappropriate installing of battery may lead to failure of the recorder system,
which is not covered by the Warranty. Do not store the recorder for a long time with a
battery inserted, as the battery may leak and lead to recorder failure, and that is not
covered by the Warranty.
For recorders with rechargeable battery, first charge the battery. To do this, gently and
without strain follow the correct polarity, connect the recorder to the USB adapter, which
is in the delivery set, aligning the mark on the recorder with the one on the adapter.
Connect the adapter to the USB port of the PC or charger device, e.g. of a mobile phone,
with the output voltage of 5V and a USB connector. During charging, the LED flashes
rarely (interval of 5 seconds), and after charging has been completed, it starts flashing
frequently. Full charging takes approximately 2.5 hours.
Please note: In order to avoid deep discharge and related damage of the rechargeable
battery, the recorder must be charged at least once a month. The failure of the
battery due to its deep discharge is a violation of the rules of operation. In case of a
complete battery discharge, the procedure to restore the operation of the Recorder
described in full operation manual.
Important!
To prevent deep discharge and related damage of the rechargeable battery, disconnect
USB adapter from the Recorder after disconnecting adapter from PC. Use only the USB
adapter included in the delivery set. Using the USB adapter of third party may cause
the recorder’s malfunction.
For recorders with external power supply – switch the recorder to OFF position and
then connect DC power supply (3.6-6V) to pins 1 (minus, gold colored wire) and 2
(plus, red colored wire) of the cable coming from the Recorder. If the voltage source
is represented by a Li-Pol battery, the connected pins 2 and 3 (green colored wire)
of the cable can provide battery charge with the current of 100mA (provided the
recorder is connected to the adapter, and the adapter is connected to the USB).
Page 6
6
Starting the record
The recorder switches to operation mode after the Switch has been shifted to ON. The
LED flashed five times and recording starts. After the transition to operation mode, the
green LED of the recorder makes two series of flashes.
The first series of LED flashes corresponds to battery charge level:
• 1 flash - charge level is 80-100%,
• 2 flashes - charge level is 20-80%,
• 3 flashes - low charge level, 0-20%;
The second series correspond to free memory card capacity:
• 1 flash states for 75-100%,
• 2 flashes – 50-75%,
• 3 flashes – 25-50%,
• 4 flashes – 1-25 %.
To stop the recording shift the Switch to OFF position. The LED will flash for 10-12
seconds and then the record stops.
Record playback
When connecting the recorder to the PC please comply with strict order: first
connect USB adapter to the recorder, next connect adapter to the PC
port (disconnection order: first disconnect the USB adapter from the PC, then
recorder from the adapter). Red and green LEDs are briefly on the adapter.
Windows recognizes a new removable drive, which contains two files:
EMPlus.exe and emplus.srv. Run “EMPlus.exe” program.
Page 7
7
During first connection there will be an offer to install program to your PC. After
accepting short and full operation manuals, EMPlus and SoundProcessor programs
and manuals will be installed to the hard drive.
Run “EMPlus.exe” program from recorder or hard drive.
Choose connection type USB 2.0 HS. The content of the recorder is on the left side of
the window. Select the desired record and click Play on the bottom of the left panel. To
upload right click on the selected record and choose «Copy to default folder» from the
context menu. The record will be converted to WAV to be displayed at the right panel.
For model B70. From page of the B70 recorder on our web-site
www.ts-market.com, from section Product files (Software) download folder
«B70 soft» to the PC. Unzip the folder and install (as Administrator) driver, file
B70_DrvSetup_1_0.exe. Slide the recorder’s cover with flash memory off in the
direction indicated by the arrow and detach it from the recorder. Connect the cover to
the USB adapter of the recorder B70. Connect the USB adapter to PC USB port. After
LED of adapter lights up, run «EMplus.exe» from the folder «B70 soft». Select type of
connection USB 2.0 Reader. The left part of the program’s window displays the
contents of the recorder’s memory. Further work with EMPlus program is the same
as for other recorders.
Reset
Incase of rechargeable battery operation error press the Reset button with sharp thing
(match or toothpick). For the recorders with batteries: remove and install battery again
in a few seconds. For the recorders with external supply: shut down and then turn on
the power supply.
Page 8
8
Warranty
The manufacturer undertakes warranty repair liabilities for 1 year from the date of
purchase, but no longer than 2 years from the date of manufacture of the product
(warranty does not cover batteries), other rules are regulated by the Law «On Protection
of Consumers' Rights».
We are always grateful for any comments and proposals regarding our products, as
well as the detailed description of the conditions and causes that led to failure. We
appreciate time and skills of our customers, and if the problem is not that complicated,
we do not mind if you try to solve the problem yourself. If the attempt to repair was
fairly neat, you do not lose your warranty. In case of major breakdowns and mechanical
damage to the recorder, your warranty will be terminated. Our products have no seals.
If you are experiencing problems with the use of our products, we recommend the
following:
• Go to www.ts-market.com and see a list of common problems (FAQ
section) and their solutions. Perhaps there is a solution to your problem.
• If the problem persists, contact technical support at support@ts-market.com
with the detailed description of your problem, the conditions it
appeared, the exact product name according to the passport, firmware,
software, operating system, and other relevant information. The better
you describe the problem, the sooner it is resolved. E-mail
correspondence is most effective because it preserves history and
minimizes misunderstanding. You will receive a response to
your request by e-mail within 24 hours (excluding
weekends and holidays).
Technical Support
Technical support is available by e-mail: support@ts-market.com
We are constantly working to improve the software and documentation. You can always
download the latest version of the software for free and get information on products on
our website: http://www.ts-market.com.
Loading...