Edge Lighting Triumph User Manual
®
© 2012 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
M-TRI-4_
M2-TRI-4_
FJ-TRI-4_
904-TRIUMPH-05
Installation Instructions for
Triumph
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Use this fixture indoors only.
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth. Oil from skin
may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations.
- This product is not restricted to certain height installation.
It is approved to be used at any height above the floor.
- Applicable accessories are Hexcell Louver and Glass
Lenses.
SAVE THESE INSTRUCTIONS!
Install the MR16 Lamp with or without a Single Optical
Control Accessory
A
FIXTURE HEAD
LENS HOLDER
RING
SMALL ALLEN
WRENCH
6
2
4
LENS
HOLDER
RING
LAMP
1
GLASS
LENS
CAP
3
CAP
CAP
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
1:
Unscrew to remove the cap from fixture head.
2: From inside the cap, use a small Allen wrench or pen point
to unscrew and remove the lens holder ring.
Use MAX 50 Watt, Type MR16 Front Glass Cover Halogen
Lamp.
If installing the MR16 lamp on its own or along with a single
3:
hexcell louver or glass lens, then place the optical accessory
(optional) followed by the MR16 lamp into the cap.
4: Replace and tighten the lens holder ring to the cap to hold
the lamp in place.
5: Pull a small portion of the socket out of the fixture head.
6: Push the lamp pins into the socket holes.
7: Screw the cap to the fixture head.
5
SOCKET
7
1
Install the MR16 Lamp with Multiple Optical Control Acessory
B
FIXTURE HEAD
3
SOCKET
LENS HOLDER
RING
SMALL ALLEN
WRENCH
4
2
1
HEXCELL LOUVER
GLASS
LENS
5
6
CAP
CAP
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
Unscrew to remove the cap from fixture head.
1:
2: From inside the cap, use a small Allen wrench or pen point
to unscrew and remove the lens holder ring. The lens holder
ring will not be used.
Use MAX 50 Watt, Type MR16 Front Glass Cover Halogen
Lamp.
Pull a small portion of the socket out of the fixture head.
3:
4: Push the lamp pins into the socket holes.
5: Place maximum of two optical glass lenses or combination
of the glass lens and hexcell louver in front of the MR16
lamp.
6: Screw the cap to the fixture body.
Install the Fixture to Monorail Connector (MC-FJ-_)
FAST JACK
C
HOUSING
1
FAST JACK HOUSING
CONNECTOR
2
MONORAIL
2
FAST JACK
FIXTURE
CONNECTOR
Install the Fixture to Monorail
2 Circuit Connector (M2C-FJ-_)
1: Place the Fast Jack housing onto the Monorail 2 Circuit and
use finger to tighten the Fast Jack housing connector to the
Fast Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack housing connector.
1: Place the Fast Jack housing onto the Monorail and use
fingers to tighten the Fast Jack housing connector to the Fast
Jack housing. Make sure that the Fast Jack housing
connector is not cross threaded.
2: Use fingers to tighten the Fast Jack fixture connector into the
Fast Jack housing connector.
FAST JACK
D
HOUSING
FAST JACK HOUSING
CONNECTOR
1
MONORAIL 2 CIRCUIT
2
FAST JACK
2
FIXTURE
CONNECTOR
2
Loading...