© 2011 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
FJ-CRYSP10-CL-WH-_
Installation Instructions for Fast Jack Crystal Spirit Pendant
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Use this fixture indoors only.
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations and
approved to be used at any height above the finished
floor.
SAVE THESE INSTRUCTIONS!
904-FJ-CRYSP10-02
Install the Fixture
A
ASSEMBLY BRACKET
3: Push the lamp pins completely into the socket holes.
4: Push the lamp shield onto the spring clips.
PHILLIPS SCREW
1
1
FABRIC
SHADE
2
FIXTURE
ASSEMBLY
FABRIC
SHADE
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
Use MAX 50 Watt, Type Bi-Pin Halogen Lamp.
1: While holding the fixture, carefully remove the three Phillips
screws from the assembly bracket.
1
2: Slightly turn the fixture assembly on its side and pull it out of
the fabric shade.
B
FIXTURE
ASSEMBLY
SOCKET
3
LAMP
SPRING CLIP
4
LAMP SHIELD
1
C
METAL DISK
5: Take one of the crystal strings and insert the hook into one
of the holes on the metal disk.
6: Repeat step 5 to install remaining crystal strings.
5
CRYSTAL STRING
D
6
METAL DISK DETAIL
HOLE
7: Install a crystal drop, by squeezing the key ring to open the
end. Slide the end through the hoop and rotate it inside the
hoop to lock in place.
8: Repeat step 7 to install remaining crystals drops.
E
STEM
COAXIAL CABLE
PHILLIPS
SCREW
9
FIXTURE
BRACKET
10
9
9
7
CRYSTAL
DROP
8
9: Feed the coaxial cable through the fabric shade and lower
the fabric shade to rest onto the assembly bracket. Secure
the shade to the assembly bracket by using the three
Phillips screws
10: Slide the stem down the coaxial cable adjacent to the
fixture assembly.
HOOP
KEY
RING
Adjust the Fixture Height
FABRIC
SHADE
1: Cut the coaxial cable to the desired height (H) with a sharp
cutter. The overall fixture height is measured from the
bottom of the crystals to the end of the coaxial cable.
F
FABRIC SHADE
CRYSTAL
1
COAXIAL
CABLE
STEM
H
2
G
2MM ALLEN
WRENCH
M4 SET SCREW
2
COAXIAL FIXTURE CONNECTOR
3
1.5MM ALLEN
WRENCH
M3 SET
SCREW
2: Loosen the two M4 set screw on base of the coaxial fixture
connector with the 2mm Allen wrench provided. Do not
remove these set screw.
3: Remove the M3 set screw on tip of the connector with the
1.5mm Allen wrench provided.
H
STRAIN RELIEF TUBE
4
4: Feed the coaxial cable through the conical nipple and flared
side of the strain relief tube. Slide the conical nipple and
strain relief tube down the coaxial cable.
I
5
COAXIAL CABLE
6: Keep feeding the coaxial cable in until the inner wire is
visible in the screw hole of the fixture connector tip. The
outer metal jacket will start to wrinkle.
7: Hold the fixture connector in place. Replace and tighten the
M3 set screw on fixture connector tip with the 1.5mm Allen
wrench.
8: Pull down the outer metal jacket to smooth the wrinkles.
COAXIAL CABLE
CONICAL NIPPLE
5: Feed the coaxial cable into the coaxial fixture connector. The
coaxial cable will come to a stop point.
J
1.5MM ALLEN WRENCH
M3 SET SCREW
WRINKLE
7
8
OUTER METAL JACK
FIXTURE CONNECTOR
INNER WIRE
6
K
2MM ALLEN WRENCH
M4 SET SCREW
9: Push the strain relief tube completely into the coaxial
fixture connector. Make sure the slot on the strain relief
tube is not inline with the M4 set screw.
10: Tighten the two M4 set screws with the 2mm Allen wrench.
COAXIAL FIXTURE
CONNECTOR
10
9
STRAIN RELIEF TUBE
3
L
11
11
11
11
11
11: Use fingers to tighten the Fast Jack fixture connector into
the Fast Jack system connector (Monorail, Monorail Wall,
Monorail 2 Circuit, or multi-port and mono-point canopies.
Refer to the instructions provided with the system
connector or canopy).
12: Refer to the instructions provided with the Monorail 2
Circuit fixture connector to choose the Circuit #1 or Circuit
#2.
CIRCUIT #1
12
CIRCUIT #2
1
2
11
11
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
1: Reach the lamp shield through the hanging crystals and
remove it.
2: Remove the old lamp.
3: Follow steps 3 & 4 in "Install the Fixture" to install the new
lamp.
N
Balancing the Fixture (Optional)
12
1
2
N
Replacing the Lamp
M
SPRING CLIP
OLD LAMP
LAMP SHIELD
2
1
N
3
2
CRYSTAL DROPS NOT SHOWN
TO AVOID CONFUSION
CYLINDER CONNECTOR
BEVELED WASHER
FIXTURE ASSEMBLY
FABRIC SHADE
NOT
BALANCED
1
NOTE: In some cases fixture may be sightly off balanced, follow
steps 1 through 3 to adjust the fixture.
1: Carefully loosen cylinder connector and the beveled washer
(do not remove) about one thread.
2: Slide the fixture assembly towards the direction of the
sagging.
3: Once the fixture is balanced tighten the beveled washer and
cylinder connector to secure fixture in place.
4
Loading...