Edge Lighting Cirrus Channel Suspension, Direct User Manual

© 2014 Edge Lighting. All Rights Reserved.

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]
www.edgelighting.com
[e-mail]

CCS-D1-_

Installation Instructions for Cirrus Channel Suspension D1

IMPORTANT INFORMATION

- This product is suitable for indoor locations.

- This instruction shows a typical installation.

SAVE THESE INSTRUCTIONS!

Connecting Channel Sections

A

CHANNEL

FEMALE
CONNECTOR

TOP OF CHANNEL

JOINER BRACKET

1

LENS

MALE
CONNECTOR

NOTE: Omit this section if the channel is made out of a single

piece.

NOTE: Prior to installation, multi-sectional Cirrus Channel should

be connected together for marking proper measurements.

NOTE: It is recommended more than one person to assist in this

installation.

1: Lift a section of the lens at the end of the channels where
the connectors are visible. Slide the channel over the joiner
bracket and ensure the male & female connectors mate
properly.

2: Push the lens back into the channel.

904-CCS-D1-06

FRONT

VIEW

3: Position the joiner bracket where the two channels meet.

Tighten four #6-32 set screws using the 1/16 Allen wrench.

CHANNEL

JOINER CHANNEL

Adjusting Cable Position

C

STRAIN RELIEF

#4-40 SET SCREW

HOLD CABLE HERE

1

SLIDING POST

COAXIAL CABLE

2

0.05" ALLEN WRENCH
#4-40 SET SCREW

CHANNEL

1

NOTE: When using Edge Lighting Slim Profile Junction Box

(C-1RE-BOX), continue to "Install the Channel using the Junction
Box (C-1RE-JBOX)" on page 3.

B

CHANNEL CHANNEL

WARNING: To avoid damaging the coaxial cable electrical

connection, make sure that the end of the coaxial cable coming
out of the fixture is held with thumb before relocating sliding
posts.

1: Loosen (DO NOT REMOVE) the #4-40 set screw on the
sliding post bushing and bed with a 0.05" Allen wrench.

2: Slide the strain relief tube out of the sliding post using a pair
of needle-nose pliers.

BACK
VIEW

1/16 ALLEN
WRENCH

JOINER BRACKET

#6-32 SET
SCREW

3

1

D

COAXIAL CABLE

3

SLIDING
POST

!CAUTION! Tightening the strain relief set screw CANNOT
BE REVERSED. Only tighten the set screw AFTER the cable

location is set properly.

4: Insert the strain relief tube back inside the sliding post
bushing and tighten the #4-40 set screw with the 0.05"
Allen wrench.

CHANNEL

3

0.05" ALLEN
WRENCH

#4-40 SET

SCREW

3: Carefully move the sliding post to the predetermined location
on channel and tighten the #4-40 set screw on the sliding
post bed with the 0.05" Allen wrench.

E

0.05" ALLEN
WRENCH

4

#4-40 SET

SCREW

STRAIN RELIEF

4

SLIDING
POST

F

0.05"ALLEN
WRENCH

#4-40 SET SCREW

5

5

5

SLIDING

POST

Install the Fixture

G

H

CANOPY

COAXIAL CABLE

AIRCRAFT CABLE

STRAIN RELIEF

STANDOFF

AIRCRAFT CABLE

5: Repeat Steps 1 through 4 for aircraft cable side.

NOTE: Run the proper size wires between the 24VDC power

supply to the electrical box. Refer to the instructions provided with
the power supply for additional information. See the wiring
diagram on page 2.

1: Measure the distance between the coaxial cable and the
aircraft cable mounted on the channel. This measurement
varies on the fixture length.

2: Mark the standoff location from the center of the electrical
box for the distant achieved on step 1.

CHANNEL

TOP VIEW

L

CANOPY

STANDOFF

3: Tap the anchors onto the marked points up to the threaded
portion with a hammer.

4: Screw in the threaded portion of the anchors with a Phillips
screwdriver.

H

CEILING

3

ANCHOR

BE FLUSH TO WALL

4

ANCHOR MUST

2