Edge Lighting Alpine User Manual

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]

www.edgelighting.com

© 2009 Edge Lighting. All Rights Reserved.

[e-mail]

Installation Instructions for Alpine

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:

- Do not look directly at the lamp while the fixture is on.

- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.

- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.

- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.

- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.

- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.

- It is normal for a new halogen lamp to produce minor
smoke when first turned on.

- Turn power off and allow to cool before replacing lamp.

ALP-W-RD-H1-_

904-ALP-W-RD-H1-05

IMPORTANT INFORMATION

- This product is ETL listed for indoor and outdoor locations.

- RISK OF FIRE:
the ground for wet locations.

- This product is for wall mount applications only.

- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.

- This product can be dimmed with a standard incandescent
dimmer.

- This instruction shows a typical installation for indoor and
outdoor.

SAVE THESE INSTRUCTIONS!

This product must be installed 4 ft above

Install the Fixture

A

2: Make sure the crossbar assembly is grounded in accordance

with local electrical codes.

3: Feed the power wires through the crossbar assembly
center hole.

FIXTURE BODY

1

CANOPY

1

SILICON WASHER

PHILLIPS SCREW

1: Remove
the fixture body and carefully pull the canopy off of the
fixture body.

the two Phillips screws and the silicon washers on

B

ELECTRICAL BOX HOLE

2

3

4

#8-32 SCREW

4

4: Mount the crossbar assembly to the electrical box holes with

the provided #8-32 screws.

CROSSBAR ASSEMBLY
CENTER HOLE

1

C

NUT

5: Feed the power wires through the canopy center hole,

SILICON GASKET

6

5

9

washer, and nut provided.

6: Slide the canopy back onto the crossbar assembly nipple
(make sure the gasket is in place) and secure the canopy to
the crossbar assembly by tightening the nut.

WASHER

7: Connect the two white fixture wires to the neutral power
wire with a wire nut.

8: Connect the two black fixture wires to the hot power wire
with a wire nut.

E

10

9

FIXTURE
BODY

9

1: Remove the metal shade by pulling it off of the socket

springs.

SILICON
WASHER

SILICON
GASKET

CANOPY

PHILLIPS SCREW

D

8

7

9: Place all wires and wire nut connections inside the fixture

body. Slide the fixture body completely onto the canopy
and make sure the silicon gasket is in place. Replace and
tighten the two silicon washers and Phillips screws.

10: For installation in wet location, caulk around the fixture
canopy with waterproof construction sealant.

Replace the Lamps

F

LAMP

SOCKET

2

1

2: Remove the old lamp by rotating it counter clockwise and

unlocking it from the socket.

3: Repeat steps 1 & 2 for other lamp.

G

4

SOCKET

FIXTURE
BODY

LARGE PORTION
OF THE
SOCKET SLOT

LAMP

4

5

METAL SHADE

CAUTION: To reduce risk of a burn or electrical shock during

lamping, disconnect the power to the fixture.

Use MAX 20 Watt Type GU10 Base PAR16 Line Voltage
Lamp With Each Socket.

4: Push the lamp into the large portion of the socket slots and
rotate it clockwise to lock it in place.

5: Slide metal shade onto the socket spring clips to secure it in
place.

6: Repeat 4 & 5 for the other socket.

2