Edge Lighting 4X4-H1 User Manual
1718 W. Fullerton Ave
www.edgelighting.com
© 2009 Edge Lighting. All Rights Reserved.
info@edgelighting.com
Installation Instructions for 4 x 4
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, exposure to
excessive UV radiation, or injury to persons:
- Do not look directly at the lamp while the fixture is on.
- RISK OF FIRE: Use only the type of lamp and maximum
wattage indicated in this instruction manual.
- Never cover the halogen lamp with anything other than a
lamp shield provided by Edge Lighting and never place
flammable material close to the fixture.
- Never turn the fixture on and off by connecting and
disconnecting the halogen lamp.
- Do not touch the fixture head, shade or lamp shield while
the fixture is on. These surfaces may be VERY HOT.
- Do not touch lamp at anytime. Use a soft cloth instead as oil
from skin may damage lamp.
- It is normal for a new halogen lamp to produce minor
smoke when first turned on.
- Do not operate the luminaire with a missing or damaged
shield.
- Turn power off and allow to cool before replacing lamp.
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
IMPORTANT INFORMATION
- This product is ETL listed for indoor and outdoor locations.
- RISK OF FIRE:
the ground for wet locations.
- This product can be wall or ceiling mounted.
- This product can mount to either a 4" square electrical box
with round plaster ring or an octagon electrical box.
- This product can be dimmed with a low voltage electronic
dimmer.
4X4-H1-_
This product must be installed 4 ft above
SAVE THESE INSTRUCTIONS!
904-4X4-H1-04
Install the Fixture
A
1
3: Connect the white transformer wire to the neutral power
wire with a wire nut.
4: Connect the black transformer wire to the hot power wire
with a wire nut.
5: Place the transformer and transformer wires inside the
electrical box.
FIXTURE CANOPY
1
MOUNTING
PLATE
PHILLIPS SCREW
2
1:
Remove the two Phillips screws on the sides of the fixture
canopy.
2: Pull the mounting plate off of the fixture canopy.
B
4
3
WIRE NUT
TRANSFORMER
1
C
MOUNTING PLATE
#8-32 SCREW
GROUND
SCREW
7
6
6
6: Line up the mounting plate with the electrical box holes, and
secure it in place by tightening the two #8-32 screws
provided.
7: Connect the transformer green wire to the mounting plate
ground screw. Make sure that the mounting plate is grounded
in accordance with local electrical codes.
ELECTRICAL BOX HOLE
8: Connect each transformer low voltage (blue wire) to one
fixture wire with a wire nut
9: Place all wires and wire connections inside the electrical box.
E
FACE
PLATE
10
11
FIXTURE
CANOPY
PHILLIPS
SCREW
10
Install the Lamp
1: While holding the fixture face plate, loosen the two
M3 set screws on the support posts (Do Not Remove) with
the provided 1.5mm Allen wrench.
2: While holding the glass ring in place, carefully remove the
face plate.
D
8
8
10: Place the fixture canopy onto the mounting plate, make
sure the gasket is in place and secure it by tightening the
two Phillips screws.
11: For installation in wet location, caulk around the fixture
fixture canopy with waterproof construction sealant.
F
FACE
PLATE
2
STUD
M3 SET SCREW
1
1
1.5MM ALLEN WRENCH
GLASS
RING
SUPPORT
POST
G
STUD
LAMP
4
SOCKET
3
1.5MM ALLEN WRENCH
CAUTION: To reduce risk of a burn or electrical shock during
lamping, disconnect the power to the fixture.
NOTE: Use only fingers and a soft cloth to install the lamp.
Use MAX 20 Watt Bi-Pin Halogen Lamp.
3: Remove the old lamp.
4: Push the new lamp pins completely into the socket holes.
5: Align the face plate studs with the support posts. Push the
face plate studs completely into the support posts and
tighten the two M3 set screws with the 1.5mm Allen wrench.
2
Loading...