Page 1
904-M2P-4RD-OUT-02
© 2009 Edge Lighting. All Rights Reserved.
1718 W. Fullerton Ave
Chicago, IL 60614
Tel: 773-770-1195
Fax: 773-935-5613
www.edgelighting.com
info@edgelighting.com
M2P-4RD-OUT-_
Installation Instructions for Monorail 2 Circuit Out Rigger Power Feed
IMPORTANT INFORMATION
- This product is ETL listed for indoor dry locations.
- This product can be installed to a 4" electrical box with
round plaster ring, or to an octagon electrical box.
- Minimum electrical box volume must be 6 cubic inches
(98 cubic centimeters).
- This product should be installed by a qualified electrician.
SAVE THESE INSTRUCTIONS!
Install the Power Feed Canopy
A
MIDDLE END
CONNECTOR
TOP END
CONNECTOR
BOTTOM END
CONNECTOR
NOTE: Use the universal round crossbar (provided) if the electrical
HOT 1
box holes are not spaced 2-3/4" apart.
NOTE: The low voltage wires should be present in the electrical
box. Refer to the instructions provided with the remote
4
HOT 2
transformer to install the transformer and the low voltage wires
before proceeding with the steps below.
1: Turn the power to electrical box off.
3
2: Connect the wire that is attached to the bottom end
connector (white wire) to the low voltage wire marked
"COM" with a wire nut.
3: Connect the wire that is attached to the middle end
2
connector to the low voltage wire marked "HOT
2" with a wire nut.
(red wire)
4: Connect the wire that is attached to the top end connector
COM
(black wire)
to the low voltage wire marked "HOT 1" with a
wire nut.
B
5: Place all wires and wire nut connections inside the electrical
box.
6: Secure the power feed canopy to the electrical box by
tightening the two provided #8-32 screws with the 3/32
Allen wrench.
HOT 1
HOT 2
COM
3/32 ALLEN WRENCH
6
6
#8-32
SCREW
5
1
Page 2
C
OUT RIGGER ARM
7
8
10: The cable post should be installed above the power feed
canopy so that there is a minimum of a 30° angle between
the out rigger arm and the aircraft cable to properly lock
the aircraft cable in position.
11: Use the tables below to determine the cable post position
relative to the out rigger arm for various angles.
7: From the end of the out rigger arm, mark the point where
out rigger arm needs
the to be shortened. (Optional)
8: Cut at the marked point with a hacksaw.
9: Clean the inside and the outside burrs where cut.
D
CABLE POST
AIRCRAFT CABLE
E
ANGLE EQUATION FOR HEIGHT (H)
30°
45°
60°
LENGTH(L) (H) FOR 30° (H) FOR 45° (H) FOR 60°
36"
24"
12"
WALL
ANCHOR
H = 0.6 x L
H = L
H = 1.7 X L
21"
14"
7"
13
14
36"
24"
12"
62"
42"
21"
H
OUT RIGGER ARM
30°
CANOPY
L
12: Mark the cable post location on the wall above the canopy.
(See table above for measurements).
13:
Using a hammer tap in the anchor on the marked
location up to the threaded portion.
14: Screw in the threaded portion of the anchor with a Phillips
screwdriver.
15: Mount the integrated washer-nipple to the anchor
using the #8 screw provided.
F
15
#8 SCREW
INTEGRATED
WASHER-NIPPLE
2
Page 3
G
AIRCRAFT CABLE
CABLE POST
16: Feed the aircraft cable through the cable post and screw
the cable post completely onto the integrated
washer-nipple.
16
INTEGRATED
WASHER-NIPPLE
17: Push the straight conductive connectors into the canopy
end connector.
I
CANOPY END
OUT RIGGER ARM
CONNECTOR
18
H
STRAIGHT CONDUCTIVE
CONNECTOR
18: Push the out rigger arm entirely onto the straight
conductive connectors and hold it in place.
CANOPY END
CONNECTOR
17
STRAIGHT
18
19: While holding the out rigger arm in place, feed the aircraft
cable through the cable grip by pushing the tab down.
20: Pull the aircraft cable out through the hole on the cable
grip. Adjust the out rigger arm so that it is perpendicular to
the wall, release the tab to lock the out rigger arm in place.
21: Trim off the excess aircraft cable coming out of the cable
grip.
CONDUCTIVE
CONNECTOR
J
AIRCRAFT CABLE
19
20
TAB
CABLE GRIP
OUT RIGGER ARM
3
Page 4
Install the Monorail 2 Circuit to
Out Rigger Power feed
K
MONORAIL
HOUSING
CONNECTOR
M5 SCREW
MIDDLE CONTACT
2
1
1.5MM ALLEN
DRIVER
1: Slightly loosen the M5 screw on the bottom of Monorail 2
circuit housing connector, (Do Not Remove) with the
2.5mm Allen wrench.
2: Loosen the two M3 set screws on the Monorail 2 circuit
housing middle contact (Do Not Remove) with the 1.5mm
Allen driver provided.
M3 SET SCREW
OUT RIGGER ARM
2.5MM ALLEN WRENCH
L
MONORAIL 2 CIRCUIT HOUSING CONNECTOR
2 CIRCUIT MONORAIL
3: Slide the Monorail 2 circuit through the opening of Monorail
2 circuit housing connector. Make sure that the Monorail 2
circuit is supported by the Monorail 2 circuit outrigger
standoffs. (Refer to the instructions provided with the
Monorail 2 circuit out rigger standoffs).
4: Adjust the Monorail 2 circuit in the Monorail 2 circuit housing
connector and tighten the M5 screw firmly with the 2.5mm
Allen wrench for proper power connection.
5: Tighten the two M3 set screws firmly on the Monorail 2
Circuit firmly housing middle contact with the 1.5mm Allen
driver for proper power connection.
M5 SCREW
2.5MM ALLEN
WRENCH
4
M3 SET SCREW
5
1.5MM ALLEN DRIVER
4
Loading...