Edge Lighting 2 Circuit 4 Round Adjustable Power Feed Canopies User Manual

904-M2P-4RD-A-03

© 2009 Edge Lighting. All Rights Reserved.

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: [phone]

Fax: [phone]
www.edgelighting.com
[e-mail]

M2P-4RD-A-_

Installation Instructions for Monorail 2 Circuit Adjustable 4" Round

Single Power Feed Canopy

IMPORTANT INFORMATION

- This product is ETL listed for indoor dry locations.

- This product can be installed to a 4" electrical box with
round plaster ring, or to an octagon electrical box.

- Minimum electrical box volume must be 6 cubic inches
(98 cubic centimeters).

- This product should be installed by a qualified electrician.

SAVE THESE INSTRUCTIONS!

Install the Canopy

A

POWER FEED
WIRES

PLASTIC DISK

NOTE: Use the universal round crossbar (provided) if the electrical

box holes are not spaced 2-3/4" apart.

NOTE: The low voltage wires should be present in the electrical

box. Refer to the instructions provided with the remote
transformer to install the transformer and the low voltage wires
before proceeding with the steps below.

5: Turn the power to electrical box off.

6: Connect the top contact wire to the low voltage wire marked

"HOT 1" with a wire nut.

4

3

2

2MM ALLEN WRENCH

CANOPY

1

M4 SET
SCREW

H

1: Loosen the two M4 set screws on the plastic disk with the

2mm Allen wrench provided.

2: Adjust the power feed wires to the desired height (from top
of the canopy to top of the Monorail - Illustrated as "H" in
diagram A) by pushing the power feed wires into the canopy.

3: Tighten the two M4 set screws firmly with the 2mm Allen
wrench.

4: Leave at least 6" of the power feed wires behind the canopy.
Trim off the excess power feed wires with a sharp cutter.
Strip 1/4" of insulation off of the power feed wires.

B

COM

8

SIDE WIRE

MIDDLE CONTACT WIRE

7

HOT 2

HOT 1

6

7: Connect the middle contact wire (coming out of the

cylindrical connector) to the low voltage wire marked
"HOT 2" with a wire nut.

8: Connect the remaining side wire to the low voltage wire
marked "COM" with a wire nut.

TOP CONTACT
WIRE

CYLINDRICAL
CONNECTOR

1

C

9: Place all wires and wire nut connections inside the electrical

box.

9

#8-32
SCREW

3/32 ALLEN
WRENCH

10

10

Install the Monorail 2 Circuit
to the Power Feed Canopy

1: Unscrew the cap from power housing.

2: Slightly loosen the 3/8-24 set screw on the cap with the
3/16 Allen wrench provided, DO NOT REMOVE THEM.

3: Slightly loosen the knurled nut on the power housing so that

the middle contact moves back and clears the power housing
opening.

10: Secure the power feed canopy to the electrical box by
tightening the two provided #8-32 screws with the 3/32
Allen wrench.

D

POWER HOUSING

CAP

3/8-24 SET SCREW

3/16 ALLEN WRENCH

1

2

MIDDLE
CONTACT

KNURLED
NUT

3

E

POWER HOUSING

4

5

CAP

MONORAIL 2 CIRCUIT

6: Tighten the 3/8-24 set screw on the cap firmly with the 3/16
Allen wrench provided for proper power connection.

7: Tighten the knurled nut firmly for proper power connection.

4: Place a section of Monorail 2 Circuit into the power housing.

Make sure that the Monorail 2 Circuit is supported by the
standoffs. Refer to the instructions provided with the
standoffs.

5: Tighten the cap to the power housing. Make sure the cap
is not cross threaded.

F

HOT 1

COM

HOT 2

7

CAP

6

KNURLED NUT

3/8-24 SET SCREW

3/16 ALLEN WRENCH

2