Edgecraft ScissorPro 500 User Manual

MODEL 500

InstructIOns

ScissorPro

®

Diamond Hone® Sharpener

© 2012 EdgeCraft Corp.

Read these instructions before use.

It is essential that you follow these

instructions to achieve optimum results.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be
followed including the following:

1. Read all instructions.

2. To protect against electrical hazards, do not immerse the ScissorPro
other liquid.

3. Make sure only clean scissor blades are inserted in the ScissorPro

4. Unplug from outlet when not in use, before putting on or taking off parts and
before cleaning.

5. Avoid contacting moving parts.

6. Do not operate any appliance with a damaged cord or plug, or after the appliance
malfunctions, or is dropped or damaged in any manner.

U.S. customers: You may return your sharpener to EdgeCraft’s factory for service where

the cost of repair or electrical or mechanical adjustment can be estimated. If the
electrical cord on this appliance is damaged, it must be replaced by the Chef’sChoice
distributor or other qualified service to avoid the danger of electrical shock.

Outside U.S.: Please return your sharpener to your local distributor where the cost of

repair or electrical or mechanical adjustment can be estimated. If the supply cord
of this appliance is damaged, it must be replaced by a repair facility appointed by
the manufacturer because special tools are required. Please consult your
Chef’sChoice distributor.

7. CAUTION! This appliance may be fitted with a polarized plug (one blade is wider than
the other). To reduce the risk of electric shock, this plug will fit in a polarized outlet only
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not modify the plug in anyway.

8. The use of attachments not recommended or sold by EdgeCraft Corporation may cause
fire, electric shock or injury.

9. The ScissorPro
and crafts scissors. Do not attempt to sharpen pinking shears, serrated blades or knives.
Do not attempt to sharpen any scissor blades that does not fit freely in the slots.

10. Do not let the cord hang over edge of table or counter, or touch hot surfaces.

11. When in the “ON” position the ScissorPro
countertop or table.

12. WARNING: SCISSORS PROPERLY SHARPENED ON YOUR ScissorPro
THAN YOU EXPECT. TO AVOID INJURY, USE AND HANDLE THEM WITH EXTREME CARE.
DO NOT CUT TOWARD ANY PART OF YOUR FINGERS, HAND OR BODY. DO NOT RUN
FINGER ALONG EDGE. STORE IN A SAFE MANNER.

13. Do not use outdoors.

14. Close supervision is necessary when any appliance is used by or near children.

15. Do not use honing oils, water or any other lubricant with the ScissorPro

16. For household use only.

17.

SAVE THESE INSTRUCTIONS.

®

Model 500 is designed to sharpen kitchen, household, sewing and arts

®

should always be on a level, stable

2

®

in water or

®

.

®

WILL BE SHARPER

®

.

CONGRATULATIONS

You are the owner of the world’s finest scissors sharpener designed to permit everyone to sharpen
scissors to professional standards, simply and easily. The ScissorPro® will put an incredibly sharp
edge on your kitchen, household, sewing and arts and crafts scissors. It is important to completely

read this booklet to optimize your sharpening results.

®

ScissorPro
scissors blade securely at a precise angle against the specially contoured, Omni-Curve™ rotating
diamond abrasive disks. These guides (see Figures 1 and 2) incorporate a unique hold-down spring
mechanism and, in combination with the magnets, comprise the unique Magne-Flex™ scissors hold­down system. Before sharpening your first scissors it is important to read the following section:

Figure 1. ScissorPro® Model 500.

owes much of its uniqueness to its precision magnetic guides, designed to hold the

Magne-Flex

Plastic Hold-Down Spring

Magnet Surface

™

Guides

Plastic Hold-Down Spring

Magnet
Surface

“Fine” Stage
Diamond Abrasives

“Coarse” Stage
Diamond Abrasives

On/Off Switch

Top of Blade

Cutter
Edge

Magnet

Figure 2. Magnets control the blade angle
and keep scissors in contact with diamond
abrasive disk.

Omni-Curve™
Diamond Disk

Figure 3. Typical scissors.

3

Pivot

Back of Blade

Anvil Edge

Tip