Page 1
Quick Start Guide
2
1
1
2
1
2
1
2
1
1
1
2
3
1
2
2-Port Wireless Access Controller
EWS4502
1. Unpack the Controller and Check Contents
EWS4502
Wireless Access Controller
Rack Mounting Kit—contains two brackets and eight
screws
Power cord—either Japan, US, Continental Europe
or UK
Console cable—RJ-45 to DB-9
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note:
For Safety and Regulatory information, refer to
the Safety and Regulatory Information document
included with the wireless controller.
2. Mount the Wireless Controller
3. Connect Power
Plug the power cord into a 100-240 VAC, 50-60 Hz AC power
source.
Insert the other end of the power cord directly into the AC
input socket on the back of the wireless controller.
Caution:
controller. For international users that may need to change
the AC power cord, you must use a cord set that has been
approved for the socket type in your country.
Use the AC power cord supplied with the wireless
4. Verify Wireless Controller Operation
Attach the brackets to the wireless controller.
Use the screws supplied with the rack to secure the wireless
controller in the rack.
Caution:
two people. One person should position the wireless
controller in the rack, while the other secures it using the
rack screws.
www.edge-core.com
Installing the wireless controller in a rack requires
Verify basic wireless controller operation by checking the
system LEDs. When operating normally, the Pwr/Sys LED
should be on green.
5. Make Initial Configuration Changes
Connect a PC to the wireless controller console port using
the included console cable.
Configure the PC’s serial port: 115200 bps, 8 characters, no
parity, one stop bit, 8 data bits, and no flow control.
– 1 –
E032015-CS-R01
150200001135A
Page 2
Quick Start Guide
3
1
2
1
2
Log in to the command-line interface (CLI) using default
settings: User name “admin” with no password.
Note:
For further wireless controller configuration
information, refer to the Administrator’s Guide and CLI
Command Reference, which are on the Edge-Core web site,
www.edge-core.com.
6. Connect Network Cables
For RJ-45 ports, connect 100-ohm Category 5, 5e or better
twisted-pair cable.
As connections are made, check the port status LEDs to be
sure the links are valid.
Hardware Specifications
Chassis
Size (W x D x H) 320 x 207.2 x 43.6 mm (12.6 x 8.16 x 1.72 in.)
Weight 1.44 kg (3.17 lb)
Temperature Operating: 0 °C to 50 °C (32 °F to 122 °F)
Storage: -40 °C to 70 °C (-40 °F to 158 °F)
Humidity Operating: 5% to 95% (non-condensing)
Interfaces
Network 2 RJ-45 1000BASE-T ports
Console RS-232 serial, RJ-45 port
Power
AC Input 100-240V AC, 50-60Hz
Power Consumption 30 Watts maximum
Maximum Current 2 A @ 100 VAC
1 A @ 240 VAC
Regulatory Compliances
Emissions CE Mark
◆
EN 55022, Class A
◆
EN 61000-3-2, Class A
◆
EN 61000-3-3
FCC Class A
BSMI CNS 13438
Immunity IEC 61000-4-2/3/4/5/6/8/11
Safety CB (IEC/EN 60950-1)
EN 60950-1: 2006+A11: 2009+A1:
2010+A12:2011 / IEC 60950-1:2005;
Am1:2009
BSMI (CNS14336-1)
– 2 –
Loading...