Edge-Core ECS4510-12PD Quick Start Manual

Quick Start Guide

L2 Gigabit Ethernet Switch

ECS4510-12PD

The ECS4510-12PD is a high-performance enterprise Layer 2 switch that provides
ten 10/100BASE-T RJ-45 ports and two Gigabit Small Form Factor Pluggable (SFP)
slots that support 1000BASE-SX and 1000BASE-LX transceivers. RJ-45 ports 1 to 8
on the switch are 802.3at PoE PD ports, and RJ-45 port 10 is an 802.3af PoE PSE port.

Note:

For detailed switch installation information, refer to the Installation Guide,

which is on the Documentation CD included with the switch.

Note:

For Safety and Regulatory information, refer to the Safety and Regulatory

Information document included with the switch.

Warning For Indoor use only:

designed for outdoor use.

The switch is designed to be installed in a standard 19-inch equipment rack.
However, you can also install the switch on any flat surface, such as a desktop.

Follow the steps in this guide to install the switch in your network.

The switch and all connected cables are not

1. Unpack the Switch Unpack the switch and check the package contents.

◆ ECS4510-12PD L2 Gigabit Ethernet Switch

◆ Rack Mounting Kit containing two brackets and eight screws for attaching the

brackets to the switch

◆ Four adhesive foot pads

◆ 3 Pin 5.08 mm pitch DC Terminal Block/Power Plug—Dinkle Cat. No. 2ESDV-03P

www.edge-core.com

– 1 –

E042014-AP-R02

150200000759A

Quick Start Guide

Attach the brackets to the switch,
then use the rack mounting screws
supplied with the rack to secure the
switch in the rack.

Attach the four adhesive rubber foot
pads to the recessed areas on the
bottom of the switch.

◆ Console cable (RJ-45 to DB-9)

◆ Quick Start Guide (this document)

◆ Regulatory and Safety Information

◆ Documentation CD — includes Installation Guide and Management Guide

2. Install the Switch The switch can be mounted in a standard 19-inch rack or on a desktop or shelf.

Rack Mounting

—Following your rack plan, mark the holes in the rack where the
switch will be installed. Lift the switch into the rack so that it is aligned with the
marked holes. With the switch brackets aligned in the proper position, secure the
switch in the rack, using four rack-mounting screws (not provided).

Desktop or Shelf Mounting

—Attach the four adhesive feet to the bottom of the

switch, then set the device on a desktop, shelf, or other flat surface.

– 2 –

3. Connect Power The ECS4510-12PD can be powered by either:

Plug the DC power plug into the
socket on the rear of the switch.

System Status LEDs

◆ PoE power from a PSE device connected to any of Ethernet ports 1 to 8

◆ From an external DC 48 VDC supply using the supplied 3-pin terminal block

plug.

To connect external DC power, connect the terminal block plug to a 48 VDC, 0.65 A
power supply using AWG 20/22 DC wiring as shown in the table and figure below.

Plug Pin Number Description

1DC + Positive

2DC - Negative

3Ground

Quick Start Guide

4. Verify Switch

Verify basic switch operation by checking the system LEDs.

Operation

When operating normally, the Power and Diag LEDs should be on green.

– 3 –

Quick Start Guide

Console Port

Connect Category 5 or better cables
with RJ-45 plugs to the RJ-45 ports.

5. Make Initial
Configuration

Changes

At this point you may need to make a few basic switch configuration changes
before connecting to the network. It is suggested to connect to the switch console
port to perform this task.

The serial port’s configuration requirements are as follows: 115200 bps, 8
characters, no parity, one stop bit, 8 data bits, and no flow control.

You can log in to the command-line interface (CLI) using default settings: User
name “admin” with password “admin.”

6. Connect Network
Cables

For information on initial switch configuration, refer to the Management Guide,
which is on the Documentation CD included with the switch.

Connect network cables to port interfaces:

◆ For the RJ-45 ports, use 100-ohm Category 5, 5e or better cable for 1000BASE-T

connections, or Category 5 or better for 100BASE-TX connections.

◆ For the SFP slots, first install SFP transceivers and then connect cabling to the

transceiver ports.

– 4 –

Quick Start Guide

For fiber transceivers, connect

62.5/125 or 50/125 multimode
or 9/125 single-mode fiber with
LC connectors.

The SFP slots support the following transceiver types: 1000BASE-SX and 1000BASE­LX.

As connections are made, check the port status LEDs to be sure the links are valid.

Note:

For further switch configuration information, refer to the Management

Guide, which is on the Documentation CD included with the switch.

– 5 –

Quick Start Guide

Hardware Specifications

Item Specification

Chassis Specifications

SIze (W x D x H) 18.00 x 16.50 x 3.75 cm (7.09 x 6.50 x 1.48 in)

Weight

Temperature Operating: 0° C to 50° C (32° F to 122° F)

Humidity Operating: 10% to 90% (non-condensing)

Power Specifications

DC Input DC 48 V 0.65 A

Maximum Power
Consumption

Regulatory Compliances

Emissions EN55022 (CISPR 22) Class A

Immunity EN 61000-4-2/3/4/5/6/8/11

Safety cTUVus (CSA 22.2 NO 60950-1 & UL 60950-1)

0.665 kg (1.47 lb)

Storage: -40° C to 70° C (-40° F to 158° F)

PoE PSE disabled: 15 W
PoE PSE enabled: 30.4 W

EN 61000-3-2/3
FCC Class A
CE Mark

CB (IEC/EN60950-1)

– 6 –