Quick Start Guide
2
1
1
2
1
2
1
2
1
2
1
2
24/48-Port GE Top-of-Rack Switch
AS4610-30T / AS4610-30P / AS4610-54T / AS4610-54P
1. Unpack the Switch and Check Contents
AS4610-30T
AS4610-30P
AS4610-54T
AS4610-54P
Rack Mounting Kit—two brackets and eight screws
Four adhesive foot pads
Power Cord—either Japan, US, Continental Europe
or UK
Console Cable—RJ-45 to DB-9
Micro-USB to RJ-45 Jack Cable
Documentation—Quick Start Guide (this document)
and Safety and Regulatory Information
Note:
For information on switch software, refer to
www.edge-core.com.
Switches with part numbers 4610-30/54-D*-******** have
switch software pre-loaded on the switch. Software user
documentation can be found at www.edge-core.com.
Switches with part numbers 4610-30/54-O-******** have
the Open Network Installer Environment software installer
pre-loaded on the switch, but no switch software image.
Information about compatible switch software can be
found at www.edge-core.com.
Use the screws and cage nuts supplied with the rack to
secure the switch in the rack.
Caution:
people. One person should position the switch in the rack,
while the other secures it using the rack screws.
Note:
using the included adhesive rubber foot pads.
Installing the switch in a rack requires two
The switch can also be installed on a desktop or shelf
3. Ground the Switch
Ensure the rack on which the switch is to be mounted is
properly grounded and in compliance with ETSI ETS 300 253.
Verify that there is a good electrical connection to the
grounding point on the rack (no paint or isolating surface
treatment).
For a PoE switch, attach a lug (not provided with PSU) to a
#12 AWG minimum grounding wire (not provided with PSU),
and connect it to the grounding point on the switch rear
panel. Then connect the other end of the wire to rack
ground.
For a Non-PoE switch, attach a lug (not provided with PSU) to
a #18 AWG minimum grounding wire (not provided with
PSU), and connect it to the grounding point on the switch
rear panel. Then connect the other end of the wire to rack
ground.
Caution:
unless all supply connections have been disconnected.
The earth connection must not be removed
4. Connect Power
Warning:
all connected cables are not designed for outdoor use.
For indoor use only. The switch, AC power, and
2. Mount the Switch
Attach the brackets to the switch.
www.edge-core.com
– 1 –
Install one or two universal AC power modules in the switch.
Connect an external AC power source to the modules.
E062015-AP-R01
150200001150A
Quick Start Guide
1
1
12312
2
1
3
123
5. Verify Switch Operation
Verify basic switch operation by checking the system LEDs.
For AS4610-30P/AS4610-54P, when operating normally, the
PSU1/PSU2, System and FAN LEDs should all be on green.
For AS4610-30T/AS4610-54T, when operating normally, the
PSU1/PSU2 and System LEDs should all be on green.
6. Perform Initial Configuration
a. Edge-Core DCSS Software (for AS4610-54P only)
To make basic switch configuration changes, connect a PC
to the switch console port using the included Micro-USB to
RJ-45 jack cable and console cable.
Configure the PC’s serial port: 115200 bps, 8 characters, no
parity, one stop bit, 8 data bits, and no flow control.
Log in to the command-line interface (CLI) using default
settings: User “admin” with no password.
Note:
For information on initial switch configuration, refer
to the Administrator’s Guide.
b. ONIE Installer Software
If the network operating system (NOS) installer is located on
a network server, first connect the RJ-45 Management
(Mgmt) port to the network using Category 5, 5e or better
twisted-pair cable. (Not required if the NOS installer is
located on attached storage.)
7. Connect Network Cables
For RJ-45 ports, connect 100-ohm Category 5, 5e or better
twisted-pair cable.
For AS4610-30P, ports 1-16 can suport PoE connections up
to 30 W and ports 17-24 can support UPoE connections up
to 60 W.
For AS4610-54P, ports 1-40 can support PoE connections up
to 30 W and ports 41-48 can support UPoE connections up
to 60 W.
Connect DAC cables to the SFP+/QSFP+ slots. Or first install
SFP+/QSFP+ transceivers and then connect fiber optic
cabling to the transceiver ports.
The following transceivers are supported:
◆
40GBASE-CR4
◆
40GBASE-SR4
◆
10GBASE-CR
◆
10GBASE-SR (ET5402-SR)
◆
1000BASE-SX (ET4201-SX)
◆
1000BASE-LX (ET4201-LX)
As connections are made, check the port status LEDs to be
sure the links are valid:
◆
On/Blinking Green — Port has a data link. Blinking
indicates network activity.
◆
On/Blinking Amber — Port has a data and PoE link.
Blinking indicates network activity.
Boot the switch. Wait for the ONIE software to locate and
execute the NOS installer, and then wait for the installer to
load the NOS software image.
Subsequent switch boots will bypass ONIE and directly run
the NOS software.
Note:
Refer to NOS installer and NOS documentation for
details on software location options and set up for ONIE.
– 2 –
Quick Start Guide
1
234
5
8. Hardware Stacking Connection (Optional)
Plug one end of a 40GBASE-CR4 DAC cable in the bottom
QSFP+ port of the top unit.
Plug the other end of the DAC cable into the top QSFP+ port
of the next unit.
Repeat for each unit in the stack.
(Optional) Plug one end of a 40GBASE-CR4 DAC cable into
the bottom QSFP+ port on the bottom unit and the other
end into the top QSFP+ port on the top unit.
Reboot each switch in the stack to start stack operation.
Note:
Stacking support is dependent on the switch
software. For stacking support information, refer to the NOS
software documentation.
Hardware Specifications
Switch Chassis
Size (W x D x H) 440 x 350 x 45 mm (17.32 x 13.78 x 1.77 inches)
Weight AS4610-30T: 5.16 kg (11.37 lb)
AS4610-30P: 6.02 kg (13.27 lb)
AS4610-54T: 5.38 kg (11.86 lb)
AS4610-54P: 6.36 kg (14.02 lb)
Temperature Operating: 0° C to 45° C (32° F to 113° F)
Storage: -40° C to 70° C (-40° F to 158° F)
Humidity Operating: 5% to 95% (non-condensing)
150 W AC PSU (AS4610-30T/ AS4610-54T)
AC Input 100-240 VAC, 50-60 Hz, 3-1.5 A
Power Rating 150 W maximum
Size (W x D x H) 54.5 x 220 x 40.25 mm (2.15 x 8.66 x 1.58 inches)
600 W AC PSU (AS4610-30P)
AC Input 100-240 VAC, 50-60 Hz, 8.5-4.25 A
Power Rating 600 W maximum
Size (W x D x H) 54.5 x 220 x 40.25 mm (2.15 x 8.66 x 1.58 inches)
920 W AC PSU (AS4610-54P)
AC Input 100-240 VAC, 50-60 Hz, 13-6.5 A
Power Rating 920 W maximum
Size (W x D x H) 54.5 x 220 x 40.25 mm (2.15 x 8.66 x 1.58 inches)
Regulatory Compliances
Emissions EN 55022:2010, Class A
EN 61000-3-2:2009, Class A
EN 61000-3-3:2008
FCC Class A
VCCI Class A
CE Mark
CCC GB9254-2008 (AS4610-54P only)
BSMI (CNS13438)
Immunity EN 55024:2010
IEC 61000-4-2/3/4/5/6/8/11
Safety UL (CSA 22.2 No 60950-1 & UL60950-1)
CB (IEC/EN60950-1)
CCC GB4943-2011 (AS4610-54P only)
BSMI (CNS14336)
– 3 –
Loading...