Eden Bath EBC009AD, EBC006AD, EBC011AD, EBC004AD, EBC005AD Installation Manual

Faucet Installation Guide

All Eden Bath products are covered under a 1 year limited warranty against manufacturing defects.

The following installation guide and its associated photos are merely an informative example of how the faucet is installed and may not be an exact representation
of the faucet you are installing. We recommend that installation should only be completed by a trained plumber. Eden Bath, its dealers, and affiliates take no re­sponsibility for the information provided below and will not be liable for any misuse or damages caused by using this information.

Large Nut Type Installation

1. Ensure the water in your home
is turned off. Attach both hold and
cold steel braided water supply
lines provided, to their respective
threaded connectors at the bot­tom of the faucet. Hot: Left - Cold:
Right.

If your faucet includes the above mounting hard­ware, please follow the set of instructions to the
right. This threaded pipe and nut may be attached to
the bottom of your faucet already.

4. Attach the nut sized rubber
gasket, then the large nut pro­vided to the threaded pipe from
underneath the countertop and
tighten with a wrench or grips
until the faucet is secured.

Screw And Horseshoe Plate Type Installation

2. Tighten both supply lines by
hand, and then with a wrench or
grips, but be careful not to over
tighten or you may strip or crack
the threaded connectors.

5. Apply plumbers tape / Teflon
tape to the threaded connectors
of your homes supply pipes. At­tach the steel braided water sup­ply lines from the faucet, to each
of the hot and cold supply valves/
connectors and tighten.

3. Attach the threaded pipe to the
bottom of the faucet if it isn't al­ready attached. Remove the
large nut and matching rubber
gasket. Insert the water supply
lines and faucet into the mounting
hole in your countertop.

If your faucet includes the above mounting hard­ware, please follow the set of instructions to the
right.

1. Ensure the water in your home
is turned off. Attach both hold and
cold steel braided water supply
lines provided, to their respective
threaded connectors at the bot­tom of the faucet. Hot: Left - Cold:
Right.

4. Place the horseshoe shaped
rubber gasket and metal plate
under the countertop with the
supply lines coming through the
open area. Attach provided
screws through plate holes and
into the faucet body and tighten.

© 2009 · Eden Bath · www.edenbath.com · [phone]

2. Tighten both supply lines by
hand, and then with a wrench or
grips, but be careful not to over
tighten or you may strip or crack
the threaded connectors.

5. Attach the nuts provided to the
threaded screw shaft and hand
tighten until flush with the metal
plate. Then do a final tightening
with a wrench or grips until the
faucet is secure.

3. If a thin circular rubber ring
was provided, place it between
the faucet and the top of the
countertop. Insert the water sup­ply lines and faucet into the
mounting hole in your countertop.

6. Apply plumbers tape / Teflon
tape to the threaded connectors
of your homes supply pipes. At­tach the steel braided water sup­ply lines from the faucet, to each
of the hot and cold supply valves/
connectors and tighten.

Sink Installation Guide

All Eden Bath products are covered under a 1 year limited warranty against manufacturing defects.

The following installation guide and its associated photos are merely an informative example of how a vessel sink is installed and may not be an exact representa­tion of the sink you are installing. We recommend that installation should only be completed by a trained plumber. Eden Bath, its dealers, and affiliates take no
responsibility for the information provided below and will not be liable for any misuse or damages caused by using this information.

Vessel Sink Installation

Above: Above Counter Vs. Recessed Installation

Above: Process for “Above Counter Mounting”

Above: Process for “Recessed Mounting”

Above: Drain Attachment

There are two different ways to mount a vessel sink.
The first is the "above counter method" which is the most

popular method and can be used for any shape or style of
vessel sink. The second is the "recessed method" which
can only be used for perfectly rounded vessel sinks (bowl
or cone) that have a smooth outer edge and are made of
a solid material such as stone, wood or copper.

In the "above counter method" the vessel sink is held in
place by the drain, adhesive between the flat bottom of
the sink and the countertop, and the weight of the sink
itself.

The “recessed method” results in a much sturdier installa­tion as a larger contact area between the sink and coun­tertop exists, adhesive used underneath the counter holds
the sink in place. The process for installing a glass vessel
is the same, however a mounting ring or thick rubber
gasket needs to be used between the top of the counter
and the bottom of the sink to prevent cracking.

ABOVE COUNTER MOUNTING

Ensure you have the appropriate sized hole in your coun­tertop. It should be just large enough to allow the
threaded drain pipe to fit through it but not the nut that is
screwed on to this pipe.

Apply a moderate amount of clear kitchen and bath rated
adhesive / caulking underneath the sink on the flattest
part around the drain. Flip the sink over and set it on your
countertop, lining up the hole in your sink and the hole in
the countertop.

Remove the nut attached to the threaded pipe of the drain
and place the drain assembly along with the upper most
rubber drain gasket (if provided) into the sinks drain hole.

RECESSED MOUNTING

Ensure you have a hole cut out in your countertop large
enough to accommodate the sink without letting it fall
through the opening.

Place the sink in the cut out area, leveling each axis to
make sure the fit is correct. From underneath the counter,
apply a bead of silicone between the sink and countertop.

Remove the nut attached to the threaded pipe of the drain
and place the drain assembly along with the upper most
rubber drain gasket (if provided) into the sinks drain hole.

DRAIN ATTACHMENT

From underneath the countertop, attach the lower most
rubber gasket and the nut onto the drain pipe. Ensure the
drain tail pipe is seated inside the P trap adapter / female
trap adapter as shown.

Thoroughly tighten the nut onto the threaded pipe of the
drain, securing the sink and drain in place.

Tighten the female trap adapter attached to your drainage
pipe until it securely grips the drains tailpipe.

* Occasionally plumbers putty or silicone may be required
between the drain and sink to ensure a leak proof seal.
Test this by running the water and evaluating.

© 2009 · Eden Bath · www.edenbath.com · [phone]