Edelbrock 5714 user manual

Page 1 of 2

Brochure #63-5714

Rev. 7/06 - KS/DA/mc

EDELBROCK CAT-BACK EXHAUST SYSTEM

For 2006 Dodge Ram, 1500 Quad Cab,

5.7L Hemi V8, 2 & 4 WD Catalog #5714

INSTALLATION INSTRUCTION

Please study these instructions carefully before installing your new Cat-Back Exhaust System. If you have any questions, contact our Technical Hotline at: 1-800-416-8628 from 7 am - 5 pm, Monday through Friday, Pacific Standard Time or e-mail us at Edelbrock@Edelbrock.com.

SUGGESTED TOOLS FOR INSTALLATION:

❑ 3/8" ratchet with deep SAE and metric sockets ❑ 9/16” and 15mm wrenches ❑ Jackstands and jack ❑ Liquid penetrant and rubber lubricant

DISASSEMBLY

1. Raise vehicle and support with proper jackstands for the weight, leaving the suspension hanging.

2. Use caution around hot exhaust systems to avoid burns.

3. Use penetrating oil on all nuts and bolts.

4. Remove the bolts and clamps from the system and lubricate the rubber hangers to ease removal.

5. Use a long pry bar to pull the rubber hangers off of the pipe hangers.

6. Remove the old system. In some cases, you will find it easier to cut the overaxle pipe to remove it.

ASSEMBLY

1. Clamp the intermediate pipe (#25-3250) to the catalytic converter with a 3” band clamp and just snug the clamp at this time. Slide hanger clamp assembly (#23-4083) onto intermediate pipe and engage wire into original front rubber isolator. Leave clamp loose at this time.

WARNING: Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before

driving!

IMPORTANT NOTE:

Proper installation is the responsibility of the installer. Improper installation will void warranty and may

result in poor performance and engine or vehicle damage.

2. Install hanger clamp assembly #23-4084 into the second I-pipe isolator on frame.

3. Slip the muffler onto the intermediate pipe with a 3” band clamp on the front. Inlet of muffler is stamped in the nipple.

4. Install hanger clamp assembly (#23-4085) onto outlet end of muffler, engage hangers into the stock rubber isolators and slip it onto the muffler outlet. Slip the overaxle pipe over the rear end and into the muffler outlet.

5. Install hanger clamp assembly (#23-4086) onto rear of the overaxle pipe and engage into factory isolator.

6. Install tailpipe and snug clamp.

7. Working from the front of the system, align and tighten each pipe from the cat-back.

8. Check for clearance to body, frame, and driveline as you tighten and align the system from front to rear.

9. Check for leaks and correct, if any are found.

INSTALLATION INSTRUCTIONS

Page 2 of 2

Brochure #63-5714

Rev. 7/06 - KS/DA/mc

KIT CONTENTS

CATALOG #5714

WARNING: Support your vehicle with proper

jackstands or ramps rated for the total vehicle weight. Place stands so that the rear axle is allowed to hang free for easy system removal.

WARNING: These cat-back systems are engineered to fit vehicles with stock catalytic converters or equivalent replacements. If your original system has been modified, Edelbrock will not warranty fit or performance.

Overaxle Pipe Assembly

Intermediate Pipe Assembly

Hanger Clamp Assembly

SDT Series Muffler #55725

Qty Part # Description

❑ 1 25-3250 Intermediate Pipe

❑ 1 25-55725 Muffler

❑ 1 23-3251 Overaxle Pipe Assembly

❑ 1 25-3157 Tail Pipe

Band Clamp

Tail Pipe Assembly

Edelbrock Corporation, 2700 California Street, Torrance, CA 90503

Tech Line: 1-800-416-8628

E-mail: Edelbrock@Edelbrock.com

Qty Part # Description

❑ 2 46-6612 3” Band Clamps

❑ 1 23-4083 I-Pipe Hanger Clamp Assembly*

❑ 1 23-4084 I-pipe Hanger Clamp Assembly*

❑ 1 23-4085 Muffler Hanger Clamp Assembly

❑ 1 23-4086 Tail Pipe Hanger Clamp Assembly*

*Not Shown.