Edelbrock 36011, 36020 User Manual

Download

Page 1

Catalog #36011, 36020 Rev. 5/06 - RS/mc 1 of 4

Brochure #63-36020

EDELBROCK PRO-TUNER EFI PRESSURE SENSORS

Catalog #36011, 36020

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and

procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected]

IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation

will void your warranty and may result in poor performance and engine or vehicle damage.

PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the "Part #____" space. THANK YOU.

DESCRIPTION: Edelbrock Pro-Tuner EFI Pressure Sensors are intended to be used with Edelbrock’s Pro-Tuner EFI system, but may be used with other

systems using the supplied connector and wiring. They are configureable to most aftermarket ECUs. If you are using another aftermarket ECU, check the sensor’s specifications with the manufacturer of your ECU. The brass body of these sensors features a 1/8” pipe thread (1/8-27 NPT) and preapplied thread sealant. Individual descriptions are as follows:

#36011: 0-100 PSI Pressure Sensor. This pressure sensor is designed to be used for monitoring fuel, oil, or other fluid pressures from

0-100 PSI.

#36020: 2-BAR Manifold Absolute Pressure (MAP) Sensor. This MAP sensor is designed to monitor manifold pressure from -29.9 in/Hg

to +14.7 PSIg. The sensor’s total range is 200 KPA.

(NOTE: PSIg = Gauge Pressure)

KIT CONTENTS:

❑ 1 Sensor ❑ 1 6” Pig-Tail Harness (Connector and 6” wiring lead) ❑ 1 Installation Instructions

INSTALLATION PROCEDURE

SENSOR MOUNTING:

The brass body of these sensors features a 1/8” pipe thread (1/8-27 NPT) and pre-applied thread sealant. You may be able to use an existing location or port, however some applications will require drilling and tapping a 1/8” NPT hole to mount the sensor.

• 36011 - 0-100 PSI Pressure Sensor Be sure to mount the sensor in a position that is fairly protected from contact with other parts, excessive heat, or possible road damage. Avoid remote mounting of the sensor, as the extended pressure line will affect the pressure signal.

• 36020 - 2-BAR Manifold Absolute Pressure Sensor The sensor should be mounted such that the connector side faces upward to avoid trapping water or condensation in the sensor tip, which will damage the sensor. Mount the MAP sensor at or as close to the intake manifold’s plenum as possible to ensure the most accurate and consistent reading.

SENSOR CONNECTIONS/WIRING:

The wiring diagram on page 2

(Figure 1)

illustrates the wire color coding and pin locations on the pig-tail harness. Refer to this figure during the

installation process.

• 36011 - 0-100 PSI Pressure Sensor If installing the 36011 (0-100 PSI Pressure Sensor) with the Edelbrock Pro-Tuner wiring harness, connect the sensor directly to the main harness. Do not use the supplied pig-tail connector. To install the sensor on a non-Edelbrock wire harness, compare the wire descriptions on the pig-tail to the descriptions supplied by the manufacturer of your harness, and connect each wire to it’s appropriate match.

• 36020 - 2-BAR Manifold Absolute Pressure Sensor To install the 36020 (MAP Sensor) to the Edelbrock Pro-Tuner wiring harness, connect each wire on the pig-tail harness to the matching wire on the Edelbrock harness as described in

Figure 1

. To install the sensor on a non-Edelbrock wire harness, compare the wire descriptions on the

pig-tail to the descriptions supplied by the manufacturer of your harness, and connect each wire to it’s appropriate match.

Page 2

Catalog #36011, 36020 Rev. 5/06 - RS/mc 2 of 4

Brochure #63-36020

Figure 1 - Pig-Tail Wire Harness and Wire Color-Coding

SENSOR SPECIFICATIONS

GENERAL SPECIFICATIONS:

Input Voltage: 4.9 to 5.1 volts DC

Overvoltage: 16 volts DC (maximum)

Reverse Polarity: 16 volts DC (maximum)

Supply Current: 5 mA (maximum)

Response Time: 6.0 mS (maximum) (To 63% of Step Input)

Minimum Load: 9.0 K OHMS (Pull-Up or Pull-Down)

DIMENSIONS:

Figure 2 - Sensor Dimensions

6.0"

Pig-Tail Harness

A - Ground (Black) B - Supply Voltage (Gray) C - Output Signal (Light Blue)

Close-Up of Connector Pins

(Connector Side)

Pro-Tuner Harness

Ground (Black/Orange) Supply Voltage (Purple/Yellow) Output Signal (Yellow)

1.67" .40"

A (Ground)

1.00"

B (Supply Voltage)

C (Output)

Page 3

Catalog #36011, 36020 Rev. 5/06 - RS/mc 3 of 4

Brochure #63-36020

2.50 101 14.69 0.00 0.00

2.60 106 15.43 0.73 1.50

2.70 111 16.16 1.47 2.99

2.80 116 16.90 2.20 4.49

2.90 122 17.63 2.94 5.98

3.00 127 18.37 3.67 7.48

3.10 132 19.10 4.41 8.97

3.20 137 19.83 5.14 10.47

3.30 142 20.57 5.88 11.97

3.40 147 21.30 6.61 13.46

3.50 152 22.04 7.35 14.96

3.60 157 22.77 8.08 16.45

3.70 162 23.51 8.82 17.95

3.80 167 24.24 9.55 19.44

3.90 172 24.98 10.28 20.94

4.00 177 25.71 11.02 22.44

4.10 182 26.45 11.75 23.93

4.20 187 27.18 12.49 25.43

4.30 192 27.92 13.22 26.92

4.40 198 28.65 13.96 28.42

4.50 203 29.38 14.69 29.91

Output Volts kPa PSIa PSIg in/Hg

0.50 0 0.00 -14.69 -29.91

0.60 5 0.73 -13.96 -28.42

0.70 10 1.47 -13.22 -26.92

0.80 15 2.20 -12.49 -25.43

0.90 20 2.94 -11.75 -23.93

1.00 25 3.67 -11.02 -22.44

1.10 30 4.41 -10.28 -20.94

1.20 35 5.14 -9.55 -19.44

1.30 41 5.88 -8.82 -17.95

1.40 46 6.61 -8.08 -16.45

1.50 51 7.35 -7.35 -14.96

1.60 56 8.08 -6.61 -13.46

1.70 61 8.82 -5.88 -11.97

1.80 66 9.55 -5.14 -10.47

1.90 71 10.28 -4.41 -8.97

2.00 76 11.02 -3.67 -7.48

2.10 81 11.75 -2.94 -5.98

2.20 86 12.49 -2.20 -4.49

2.30 91 13.22 -1.47 -2.99

2.40 96 13.96 -0.73 -1.50

36020 - 2-BAR Manifold Absolute Pressure Sensor

2.50 446.0 50.00

2.60 463.3 52.50

2.70 480.5 55.00

2.80 497.7 57.50

2.90 515.0 60.00

3.00 532.2 62.50

3.10 549.4 65.00

3.20 566.7 67.50

3.30 583.9 70.00

3.40 601.2 72.50

3.50 618.4 75.00

3.60 635.6 77.50

3.70 652.9 80.00

3.80 670.1 82.50

3.90 687.3 85.00

4.00 704.6 87.50

4.10 721.8 90.00

4.20 739.1 92.50

4.30 756.3 95.00

4.40 773.5 97.50

4.50 790.8 100.00

Output Volts kPa PSIg

0.50 101.3 0.00

0.60 118.5 2.50

0.70 135.8 5.00

0.80 153.0 7.50

0.90 170.2 10.00

1.00 187.5 12.50

1.10 204.7 15.00

1.20 222.0 17.50

1.30 239.2 20.00

1.40 256.4 22.50

1.50 273.7 25.00

1.60 290.9 27.50

1.70 308.1 30.00

1.80 325.4 32.50

1.90 342.6 35.00

2.00 359.8 37.50

2.10 377.1 40.00

2.20 394.3 42.50

2.30 411.6 45.00

2.40 428.8 47.50

36011 - 0-100 PSI Pressure Sensor

SENSOR CALIBRATION:

Edelbrock Pressure Sensors are pre-calibrated for use with Edelbrock Pro-Tuner software. If you are using another aftermarket ECU system, you will need to calibrate the sensors using your software. Refer to the following charts and enter the values required by your software to calibrate the sensors to your software.

Page 4

Catalog #36011, 36020 Rev. 5/06 - RS/mc 4 of 4

Brochure #63-36020

Edelbrock Corporation • 2700 California St. • Torrance, CA 90503

Tech-Line: 1-800-416-8628 • E-Mail: [email protected]