CC2530 Zigbee Module
ITEM
PARAMETER
UNIT
MIN
TYPICAL
MAX
Voltage supply
3.0
3.3
3.6
V
Transmitting
current
36
38
40
mA
Receiving current
25
26
27
mA
Sleep
consumption
1
uA
frequency
2.405
2.485
GHz
Output power
3.8
4.0
4.2
dBm
Receiving
sensitivity
-97
dBm
Data rate
250
Kbps
Transmit distance
100
m
CC2530 Zigbee Wireless RF Module
General Description
The CC2530 Zigbee RF Module is a low-power, highly integrated 2.4-GHz transceiver that suitable for systems
targeting compliance with worldwide radio-frequency. It’s a true system-on-chip solution for 2.4-GHz IEEE802.15.4,ZigBee
applications.
Electrical Characteristics
Ta = 25°C, VCC = 3.3V
Typically, equipment utilizing this device requires emissions testing and government
approval, which is the responsibility of the equipment manufacture.
1 / 6
Baud Rate
2400
9600
115200
bps
Operating
temperature
-40
80
℃
Package size
28×20×2 mm
Radio
·2.4-GHz IEEE802.15.4 compliant RF transceiver
·Excellent receiver sensitivity and robustness to interference, receiver sensitivity reach to -97dBm
·Programmable output power up to 4.5dBm
·Suitable for systems targeting compliance with worldwide radio-frequency
·Accurate digital RSSI/LQI support
·data rate: 250kBank
8051 MCU
·Powerful five-channel DMA
·128KB in-system programmable flash, customization 32-,64-,256KB
·8KB RAM with retention in all power modes
·CSMA/CA hardware support
·AES security coprocessor
·Battery monitor and temperature sensor
·12-Bit ADC with eight channels and configurable resolution
·Two powerful USARTs with support for several serial protocols
·IEEE 802.15.4 MAC timer, general-purpose timers (One 16-Bit, Two 8-Bit)
·32-kHz sleep timer with capture
·Watchdog timer
·21 general-purpose I/O pins (19× 4 mA, 2×20 mA)
·Hardware debug support
-CC2530-Z1 RF Module
·Applications
·2.4-GHz IEEE 802.15.4 systems
·Zigbee systems (256-KB flash)
·Home/Building automation
·Lighting systems
·Industrial control and monitoring
·Low-Power wireless sensor networks
·Consumer electronics
·Health care
2 / 6
CC2530-Z1 RF Module
Pin namee
Pin typ
Description
VCC
Power
DC 2.0－3.6V
GND
Ground
GND
RESET_N
reset
CC2530 RESET
P0.0
Digital I/O
CC2530 P0.0
P0.1
Digital I/O
CC2530 P0.0
P0.2
Digital I/O
CC2530 P0.2
P0.3
Digital I/O
CC2530 P0.3
P0.4
Digital I/O
CC2530 P0.4
P0.5
Digital I/O
CC2530 P0.5
P0.6
Digital I/O
CC2530 P0.5
P0.7
Digital I/O
CC2530 P0.5
P1.0
Digital I/O
CC2530 P1.0
·Package Description
Pin Description
Pin name Pin type Description
3 / 6
P1.1
Digital I/O
CC2530 P1.1
P1.2
Digital I/O
CC2530 P1.2
P1.3
Digital I/O
CC2530 P1.3
P1.4
Digital I/O
CC2530 P1.4
P1.5
Digital I/O
CC2530 P1.5
P1.6
Digital I/O
CC2530 P1.6
P1.7
Digital I/O
CC2530 P1.7
P2.0
Digital I/O
CC2530 P2.0
P2.1
Digital I/O
CC2530 P2.1
P2.2
Digital I/O
CC2530 P2.2
ANT
Antenna interface
50ohm
Note:
1. P2.3 and P2.4 connect to a 32768 KHz crystal.
2. Spring Antenna or PCB Antenna can be choice.
3. Read TI CC2530 datasheet for detail.
4 / 6
Develop & Debug
USB Interface
Power Led
Debug Interface
power supply
(5～8V)
RS232
Interface
RS485 Interface
USB\232\485 SEL
Zigbee Base
IO Interface
Power selection
communication
Led
Led Enable
Using Zigbee base board, it is easy to develop wireless application.
Inserting Zigbee module into base board, then, Connecting computer and Zigbee base board. In computer, running Comm
UART Assist or other Comm debug software, As shown in the following illustration.
5 / 6
Setting com port, Baudrate etc, Default Baudrate setting 9600, parity NONE, DataBit 8, StopBit 1. then send data, zigbee
module transmit RF data, other zigbee module receive data.
6 / 6
Loading...