Edbak PWB1 Instruction Manual

4. Security screw

When the screen is hanging securely on the back plate,
tighten solidly two security screws situated in bottom
part of front panels using Phillips screw driver.

5. Maintenance

Before maintenance of wall mount it is necessary to turn off and unplug plasma/LCD screen.
Wipe the screen up with dry cloth. If the wall mount is very dirty, it is necessary to remove the dirt first with
neutral cleaner diluted with water, and than wipe the mount up with dry cloth. You can not use such cleaners
like solvent, furniture wax as it may cause peeling off of the powdercoated metal parts.

EDBAK Sp. z o.o.

Piotrowice 186, 23-107 Strzyżewice, Poland

www.edbak.com [e-mail]

Rev. date: 31.07.2006

PWB1

UNIVERSAL FIXED WALL MOUNT PWB1

FOR 32-60” PLASMA /LCD SCREENS

Installation manual

SAFETY WARNING!
Remarks regarding safety and installation

INSTRUCTIONS MUST BE ALWAYS FOLLOWED PRECISELY

1. Before installation read carefully this installation manual and instruction manual of your

plasma/LCD screen for proper installation.

2. Installation of this unit should be carried out by at least two qualified technicians.

3. This unit is not adapted to direct installation on the ceiling surface. Mounting to the ceiling is

only possible with CM1 adapter.

4. EDBAK is not liable for any damage or injury caused by mishandling or improper installation.

5. Maximum capacity load: 80 kg

6. Mounting interface: min. 100x100 mm, max 750x460mm

Universal Fixed Wall Mount PWB1

List of components:

1. Back plate – 1 pcs.

2. Front plate – 2 pcs.

3. Fixings and fixtures - 1 bag

1

4. Instruction manual – 1 pcs.

Tools required for installation (not

included):

- Allen key nr 3,4,5, 6 – 1 pcs.

2

- Phillips PH2 screwdriver – 1 pcs.

Formatiert: Schriftart: Fett

Gelöscht: Every 6 months run

periodical check the condition of
screw joints and in case there ¶

Gelöscht: .

Gelöscht: 5

Gelöscht: .

Gelöscht: ¶

1. Mounting back plate on the wall surface

Mounting of the back plate to the wall
should be carried out in desired position
after prior checking of wall type and
structure and according to building craft.
If you have any doubt please consult a
qualified builder or contractor. It is not
allowed to mount a screen on the wall
which structure is not durable enough to
hold the specified capacity load.

Mount back plate horizontally to the wall

Bottom

surface using screws/bolts (not supplied) suitable to
the type and structure of wall.

2. Mounting front plates to the back of plasma / LCD screen

Screw

Top

In the enclosed bag there are different screws, washers and spacers fitting different types and makes of
plasma/LCD screens. Only ONE set of screws, washers and spacers will be necessary for mounting front plates
to the back of plasma/LCD screen.
Compile set of screws, washers and spacers in the following manner:

- select suitable height of spacers, in order to keep a couple millimeters distance between the back of the
plasma/LCD screen and front panels

- select suitable screws (length and thread), so that after assembling spacers, front panels and washers
together the depth mounting pole back of the plasma/LCD screen is adequate to the length of the screw
thread. Screw can not be too long, because while screwing in it may cause damage to your screen.

Position front panels centrally on the back of the screen
Tighten previously selected screws using Allen key.

Screen center

Center holes

Gelöscht: on

Gelöscht: <sp><sp>

Gelöscht: as

Gelöscht: <sp><sp>

Formatiert: Schriftart: (Standard)

Arial

Washer

Top of the screen

Front plate

Spacer

Mounting

hole

Bottom of the

screen

Place plasma/LCD screen face down on soft cloth (to prevent damage) on a flat and stable surface.

Please compile all parts necessary for mounting:

front plate – 2 pcs
screw – 4 pcs.
washer – 4 pcs.
spacer – min. 4 pcs.

Allen key

3. Mounting screen on the back plate

Please be careful while engaging plasma with the
wall!!

Raise the screen in vertical position (at least two people)

Gelöscht: Klucz imbusowy

Formatiert: Schriftart: (Standard)

Arial

with front plates already assembled to the back of the
screen and hang it on the back plate mounted on the wall
surface, so that hooks hang on the edge of the back plate
(please see the drawing).

Make sure that the hooks are hooked on the edge of the back plate.