ECS Z97-PK User Manual

Z97-PK
USER MANUAL
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac­turer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publica­tion and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.
Other product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal­lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits govern­ing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
ii
Z97-PK
USER MANUAL
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the follow­ing conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference
that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference­causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
The manual consists of the following:
Describes features of the motherboard.
page 1
Describes installation of motherboard components.
page 7
page 29
page 65
Installing the Motherboard
Introducing the Motherboard
Provides information on us­ing the BIOS Setup Utility.
Chapter 5
Describes the motherboard software.
page 69
Limits and methods of mesurement of radio disturbance char­acteristics of information technology equipment
EN 55022
EN 61000-3-2
Disturbances in supply systems caused
EN 61000-3-3
Disturbances in supply systems caused by household appli­ances and similar electrical equipment “ Voltage fluctuations”
EN 55024
Information technology equipment-Immunity characteristics­Limits and methods of measurement
EN 60950
Safety for information technology equipment including electri­cal business equipment
CE marking
About the Manual
This device is in conformity with the following EC/EMC directives:
Chapter 4
Chapter 1
Chapter 2
Chapter 3 Using BIOS
Using the Motherboard Software
Chapter 7 Trouble Shooting
Provides basic trouble shooting tips.
page 77
Intel
®
Matrix Storage Manager
RAID Configurations
Describes Intel
®
Matrix Storage Manager RAID Configurations.
Chapter 6
AMD CrossFireX
TM
Technology
Support
Describes AMD Crossfire
TM
Technology
page 75
iii
Z97-PK USER MANUAL
Chapter 2 7
Installing the Motherboard 7
Safety Precautions.............................................................................7
Installing the Motherboard in a Chassis......................................7
Checking Jumper Settings.................................................................8
Installing Hardware..................................................................9
Installing the Processor.............................................................9
Installing the CPU Cooler.........................................................11
Installing Memory Modules....................................................12
Installing Add-on Cards...........................................................14
Connecting Optional Devices..................................................16
Installing a SATA Hard Drive...................................................24
Connecting Case Components.......................................................25
Front Panel Header.................................................................27
TABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction...................................................................................1
Pakage Contents............................................................................1
Specifications................................................................................2
Motherboard Components..........................................................4
I/O Ports..............................................................................................6
Chapter 3 29
Using BIOS 29
About the Setup Utility................................................................29
The Standard Configuration....................................................29
Entering the Setup Utility........................................................29
Resetting the Default CMOS Values.....................................30
Using BIOS........................................................................................30
BIOS Navigation Keys..............................................................31
Main Menu.............................................................................32
Advanced Menu......................................................................33
Chipset Menu..........................................................................44
M.I.B III(MB Intelligent Bios III) Menu....................................52
Security Menu..........................................................................60
Boot Menu...............................................................................61
Exit Menu................................................................................62
iv
Z97-PK
USER MANUAL
Updating the BIOS...........................................................................63
Chapter 7 77
Trouble Shooting 77
Start up problems during assembly..............................................77
Start up problems after prolong use............................................78
Maintenance and care tips..............................................................78
Basic Troubleshooting Flowchart...................................................79
Chapter 6 75
AMD CrossFireXTM Technology Support 75
Requirements....................................................................................75
Installing CrossFireXTM graphics cards......................................75
The Catalyst
TM
Control Center Dialog Box...................................76
Chapter 5 69
Intel® Rapid Storage Technology RAID Configuration 69
Before creating a RAID set...................................................................69
Entering Intel® Rapid Storage Technology RAID BIOS utility......70
Creating a RAID set..........................................................................71
Deleting a RAID set...............................................................................73
Resetting disks to Non-RAID..............................................................74
Exiting Setup.........................................................................................74
Chapter 4 65
Using the Motherboard Software 65
Auto-installing under Windows XP/7/8......................................65
Running Setup.........................................................................65
Manual Installation..........................................................................67
ECS Utility Software (Intelligent EZ Utility).....................................67
1
Z97-PK
USER MANUAL
Chapter 1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the Z97-PK motherboard. This motherboard is a high perfor­mance, enhanced function motherboard designed to support the LGA1150 socket for Intel® 4th and 5
th
Generation CoreTM Family processors.
This motherboard is based on Intel
®
Z97 Express Chipset for best desktop platform
solution. It supports up to 32 GB
of system memory with dual channel DDR3 1600/ 1333 MHz. One PCI Express x16 Gen3 slot (Gray slot) and one PCI Express x16 Gen2 slot (Black slot runs at x4 mode) are supported, intended for Graphics Interface. In addition, one PCI Express x1 Gen2 slot is for extending usage.
It integrates USB 2.0 and USB 3.0 interface, supporting up to ten USB 2.0 ports (four USB 2.0 ports at rear panel and three USB 2.0 headers support additional six USB 2.0 ports) and four USB 3.0 ports (two USB 3.0 ports at the rear panel and one USB 3.0 header supports additional two USB 3.0 ports). The gray USB 2.0 header provides EZ charger technology, please refer to
Front Panel USB 2.0 headers of chapter 2 for
more details.
The motherboard is equipped with advanced full set of I/O ports in the rear panel, including one PS/2 mouse and keyboard Combo connector, one VGA port, one DVI port, one HDMI port, one RJ45 LAN connector, four USB 2.0 ports, two USB 3.0 ports and audio 8-ch jacks.
In addition, this motherboard supports six SATA 6Gb/s connectors for expansion.
Your motherboard package ships with the following items:
Package Contents
Z97-PK Motherboard Quick Installation Guide User Manual DVD I/O Shield 2 SATA 6G Cables
     
The package contents above are for reference only, please take the actual package items as standard.
Chapter 1
2
Z97-PK
USER MANUAL
CPU
Specifications
Intel® Z97 Chipset
Chipset
Dual-channel DDR3 memory architecture
4 x 240-pin DDR3 DIMM sockets support up to 32 GB
Supports DDR3 1600/1333 MHz SDRAM
Memory
Supported by Intel® Z97 Express Chipset
- 6 x Serial ATA 6Gb/s devices
- RAID 0, RAID 1, RAID 5, RAID 10 configuration
Expansion Slots
Storage
1 x PS/2 mouse & keyboard Combo connector
1 x D-sub (VGA port)
1 x DVI port
1 x HDMI port
4 x USB 2.0 ports
1 x RJ45 LAN connector
2 x USB 3.0 ports
1 x Audio 8-ch jacks
Rear Panel I/O
LAN
Realtek RTL8111G Gigabit Lan
Realtek ALC892 8-Ch High Definition audio CODEC
- Compliant with HD audio specification
Audio
LGA1150 socket for
Intel® 4th and 5
th
Generation CoreTM Family
processors
Supports CPU up to 84W, TDP up to 95W
Supports Intel® Turbo Boost Technology
Supports Intel
®
Hyper-Threading Technology
Supports Intel
®
64 Architecture
Supports Intel
®
Advanced Vector Extensions 2.0
Supports Intel
®
Responsiveness Technologies
- Intel
®
Rapid Storage Technology 12
- Intel® Smart Response Technology*
- Intel® Rapid Start Technology*
Note: Please go to ECS website for the latest CPU support list.
Note: Please go to ECS website for the latest Memory support list.
AMD CrossFireX
TM
Technology
Supports AMD CrossFireXTM Technology
- The PCIEX16_S1 (black color of PCIE x16 slot) supports PCI Express Gen2 running at X4 mode
2 x PCI Express x16 slots (one PCI Express Gen3 x16 slot & one PCI Express Gen2 x4 mode slot)
1 x PCI Express x1 Gen2 slot
*SSDS, multiple HDDs required.
Internal I/O Connectors & Headers
1 x 24-pin ATX Power Supply connector
1 x 4-pin ATX 12V Power connector
1 x 4-pin CPU_FAN connector
1 x 4-pin PWR_FAN connector
1 x 4-pin SYS_FAN connector
1 x USB 3.0 header supports additional two USB 3.0 ports
3
Z97-PK
USER MANUAL
Chapter 1
AMI BIOS with 64Mb SPI Flash ROM
Supports Plug and Play, STR (S3)/ STD(S4), Hardware Monitor
Audio, LAN, can be disabled in BIOS
F7 hot key for boot up devices option
Supports ACPI & DMI
Supports PgUp clear CMOS Hotkey (Has PS2 KB Model only)
Supports 3 Independent Dispaly
Supports Multi-Language
Supports AC’97/HD Audio auto detect (default)
System BIOS
Micro ATX Size, 244mm x 220mmForm Factor
Supports eBLU*1/eDLU/eSF*1/Cyberlink*2/Norton*2/Muzee*2/EZ Charger
AP Support
Note: *1Microsoft .NET Framework 3.5 is required.
3 x USB 2.0 headers support additional six USB 2.0 ports (Gray
header supports EZ charger)
6 x SATA 6Gb/s connectors
1 x SPDIF out header
1 x Front Panel audio header
1 x Front Panel switch/LED header
1 x CIR header
1 x COM header
1 x CLR_CMOS jumper
1 x Parallel port header (LPT)
1 x Trusted platform module header (TPM)
1 x Speaker header
1 x Case open header
1 x ME_UNLOCK header
*2Free bundle software including ECS DVD: Cyberlink/Norton/
Muzee.
Chapter 1
4
Z97-PK
USER MANUAL
Motherboard Components
5
Z97-PK
USER MANUAL
Chapter 1
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket
LGA1150 socket for Intel
®
4th and 5
th
Generation Core
TM
Family processors
2. PWR_FAN 4-pin power cooling fan connector
3. SYS_FAN 4-pin system cooling fan connector
4. CPU_FAN 4-pin CPU cooling fan connector
5. DDR3_1~4 240-pin DDR3 Module slots
6. ATX_POWER Standard 24-pin ATX power connector
7. USB3F Front panel USB 3.0 header
8. CASE CASE open header
9. ME_UNLOCK ME unlock header-for factory use only
10. SATA1~6 Serial ATA 6Gb/s connectors
11. F_PANEL Front panel switch/LED header
12. F_USB1 Front panel USB 2.0 header (Gray header supports EZ Charger)
13. F_USB2~3 Front panel USB 2.0 headers
14. TPM Trusted platform module header
15. LPT Parallel port header
16. SPDIFO1 SPDIF out header
17. SPK Speaker header
18. CIR1 Consumer Infrared
19. COM Onboard serial port header
20. CLR_CMOS Clear CMOS jumper
21. PCIEX16_S1 PCI Express Gen2 x4 slot
22. F_AUDIO1 Front panel audio header
23. PCIE1 PCI Express Gen2 x1 slot
24. PCIEX16 PCI Express Gen3 x16 slot for graphics interface
25. ATX12V 4-pin +12V power connector
Chapter 1
6
Z97-PK
USER MANUAL
I/O Ports
1. PS/2 Combo port
Use the PS/2 combo port to connect the PS/2 Keyboard or PS/2 Mouse.
2. USB 2.0 Ports
Use the USB 2.0 ports to connect USB 2.0 devices.
3. VGA Port
Connect your monitor to the VGA port.
4. DVI Port
Connect your monitor to the DVI port.
5. HDMI Port
You can connect the display device to the HDMI port.
6. USB 3.0 Ports
Use the USB 3.0 ports to connect USB 3.0 devices.
7. LAN Port
Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
8. Audio Ports
Use the audio jacks to connect audio devices. The D port is for stereo line-in signal, while the F port is for microphone in signal. This motherboard supports 8-channel audio devices that correspond to the A, B, C, and E port respectively. In addition, all of the 3 ports, B, C, and E provide users with both right & left channels individually. Users please refer to the following note for specific port function definition.
LAN LED Status Description
OFF No dat a Orange blinking Active OFF No link Green Link
Activity LED
Link LED
Link LED
LAN Port
The above port definition can be changed to audio input or audio output by changing the driver utility setting.
A: Cente r & Woofe r D: Line -in
B: Ba ck Surr ound E: Fro nt Out
C: Si de Surroun d F: Mic_in Rear
Chapter 2
7
Z97-PK USER MANUAL
Chapter 2
Installing the Motherboard
2-1. Safety Precautions
2-2. Installing the motherboard in a Chassis
This motherboard carries a Micro ATX form factor of 244 x 220 mm. Choose a chassis that accommodates this from factor. Make sure that the I/O template in the chassis matches the I/O ports installed on the rear edge of the motherboard. Most system chassis have mounting brackets installed in the chassis, which corresponds to the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.
Follow these safety precautions when installing the motherboard:
Wear a grounding strap attached to a grounded device to avoid damage from static electricity.
Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard.
Leave components in the static-proof bags.
Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.
Do not over-tighten the screws as this can stress the motherboard.
Chapter 2
8
Z97-PK USER MANUAL
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.
2-3. Checking Jumper Settings
Chapter 2
9
Z97-PK USER MANUAL
2-4. Installing Hardware
2-4-1. Installing the Processor
This motherboard has an LGA1150 socket.
When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
You may be able to change the settings in the system Setup Utility. We strongly recommend you do not over-clock processor or other compo­nents to run faster than their rated speed.
The following illustration shows CPU installation components.
A. Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab.
B. Lift the tail of the load lever and rotate the load plate to fully open position.
C. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.
Chapter 2
10
Z97-PK USER MANUAL
D. Rotate the load plate onto the package IHS (Intergraded Heat Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically.
Please save and replace the cover onto the CPU socket if processor is removed.
Chapter 2
11
Z97-PK USER MANUAL
A. Apply some thermal grease onto the contacted area between the heatsink and the CPU, and make it to be a thin layer.
B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector.
C. Connect the CPU cooler power connector to the CPU_FAN connector.
2-4-2. Installing the CPU Cooler
Install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
Avoid using cooling fans with sharp edges in case the fan casing and the clips cause serious damage to the motherboard or its components.
To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heat sink instal­lation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.
DO NOT remove the CPU cap from the socket before installing a CPU.
Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1150 socket.
The following illustration shows how to install CPU fan.
Chapter 2
12
Z97-PK USER MANUAL
2-4-3. Installing Memory Modules
This motherboard accommodates four memory modules. It can support four 240-pin DDR3 1600/1333 MHz.
Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
You must install at least one module in any of the four slots. Total memory capacity is 32 GB.
Refer to the following to install the memory modules.
C. The slot latches are levered upwards and latch on to the edges of the
DIMM.
A. Push the latches on each side of the DIMM slot down.
B. Install the DIMM module into the slot and press it firmly down until it
seats c
orrectly. Check that the cutouts on the DIMM module edge
connector match the notches in the DIMM slot.
The four DDR3 memory sockets (DDR3_1, DDR3_2, DDR3_3 and DDR3_4) are divided into two channels and each channel has two memory sockets as following:
Channel A: DDR3_1, DDR3_2 Channel B: DDR3_3, DDR3_4
Chapter 2
13
Z97-PK USER MANUAL
Recommend memory configuration
Model
Sockets
DDR3_1 DDR3_2 DDR3_3 DDR3_4
1 DIMM ~ Populated ~ ~
1 DIMM ~ ~ ~ Populated
2 DIMMs
~ Populated ~ Populated
3 DIMMs Populated Populated ~ Populated
3 DIMMs
~ Populated Populated Populated
4 DIMMs Populated Populated Populated Populated
Due to Intel CPU spec definition, please follow the table above for recommended memory configuration.
1. For best performance and compatibility, we recommend that users give priority to the white DIMMs (DDR3_2/DDR3_4) when installing DIMMs.
2. We suggest users not to mix memory type. It is recommended to use the same brand and type memory on this motherboard.
Chapter 2
14
Z97-PK USER MANUAL
2-4-4. Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 2.0.
PCIE1 Slot
Recommend add_on card configuration
PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI Ex-
press graphics card that is fully compliant to the PCI Express Base Specification revision 3.0.
PCIEX16_S1 Slot This slot is fully compliant to the PCI Express Base Specification
revision 2.0 which runs at x4 mode.
PCIEX16 PCIEX16_S1
SPEC PCI-E Gen.3 Running x16 mode PCI-E Gen.2 Running x4 mode Color Gray Black
1 Graphic Card (VGA card) Populated --
Model
PCIEX16 Slots
Chapter 2
15
Z97-PK USER MANUAL
1 Remove a blanking plate from the system case corresponding to the slot
you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.
Follow these instructions to install an add-on card:
Please refer the following illustrations to install the add-on card:
Install the LAN Card in the PCIE X1 slot
Install the VGA Card in the PCIE X16 slot
Chapter 2
16
Z97-PK USER MANUAL
2-4-5. Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
No. Components No. Components
1USB3F 7 TPM
2CASE8 LPT
3ME_UNLOCK 9 SPDIFO1
4SATA_1/210 CIR1
5SATA3~611 COM
6 F_USB1~3 12 F_AUDIO1
Chapter 2
17
Z97-PK USER MANUAL
Please make sure that the USB cable has the same pin assignment as indi­cated above. A different pin assignment may cause damage or system hang­up.
This Motherboard implements one USB 3.0 header supporting 2 extra front USB 3.0 ports, which delivers 5Gb/s transfer rate.
1. USB3F: Front Panel USB 3.0 header
2. CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.
Chapter 2
18
Z97-PK USER MANUAL
3. ME_UNLOCK: ME Unlock Header
SATA1~6 connectors are used to support the Serial ATA 6.0Gb/s device, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Paral­lel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
4 & 5. SATA1~6: Serial ATA connectors
Chapter 2
19
Z97-PK USER MANUAL
Unlike F_USB2 & F_USB3, F_USB1 supports EZ Charger technology, provides 3 times current than general USB port in off mode for USB devices. It is useful and excellent, especially for the iPhone, iPad and iPod touch devices that need a large amount of current for faster recharging within less time.
The motherboard has three USB 2.0 headers supporting six USB 2.0 ports. Addition­ally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
6. F_USB1~3: Front Panel USB 2.0 headers
Please make sure that the USB cable has the same pin assignment as indi­cated above. A different pin assignment may cause damage or system hang­up.
7. TPM: Trusted Platform Module header
Trusted platform module (TPM) is a published specification detailing a microcontroller that can store secured information, and implementations of that specification.
Chapter 2
20
Z97-PK USER MANUAL
This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.
9. SPDIFO1: SPDIF out header
This is a header that can be used to connect to the printer, scanner or other devices.
8. LPT: Onboard parallel port header
Chapter 2
21
Z97-PK USER MANUAL
11. COM: Onboard serial port header
Connect a serial port extension bracket to this header to add a serial port to your system.
10. CIR1: Consumer Infrared Header
Chapter 2
22
Z97-PK USER MANUAL
If you use AC97 Front Panel, please tick off the option of Disabled Front Panel Detect . If you use HD Audio Front Panel, please dont tick off Disabled Front Panel Detect .
* For reference only
AC97 Audio Configuration: To enable the front panel audio connector to support AC97 Audio mode.
The front panel audio header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC97 front panel audio to HD onboard headers, please set as below picture.
12. F_AUDIO1: Front Panel Audio Header
Chapter 2
23
Z97-PK USER MANUAL
If you use AC97 Front Panel, please dont tick off Using Front Jack Detect . If you use HD Audio Front Panel, please tick off the option of Using Front Jack Detect .
* For reference only
Chapter 2
24
Z97-PK USER MANUAL
2-4-6. Installing a SATA Hard Drive
About SATA Connectors
Your motherboard features six SATA connectors supporting a total of six drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with a SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
* For reference only
Installing Serial ATA Hard Drives
This section describes how to install a SATA Hard Drive.
Chapter 2
25
Z97-PK USER MANUAL
No. Components No. Components
1 PW R_FAN 5 F_P ANEL
2SYS_FAN6 SPK
3CPU_FAN 7ATX_12V
4ATX_POWER~ ~
After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:
2-4-7. Connecting Case Components
Chapter 2
26
Z97-PK USER MANUAL
1. PWR_FAN (Power Cooling FAN Connector) & 2. SYS_FAN (System cooling FAN Connector) & 3. CPU_FAN (CPU Cooling FAN Connector)
Connect the CPU cooling fan cable to CPU_FAN.
Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V.
Connect the system cooling fan connector to SYS_FAN.
4. ATX_POWER (ATX 24-pin Power Connector) & 7. ATX12V (ATX 12V Power Connector)
Connect the standard power supply connector to ATX_POWER. Connect the auxiliary case power supply connector to ATX12V.
Connect the power cooling fan connector to PWR_FAN.
Chapter 2
27
Z97-PK USER MANUAL
5. F_PANEL: Front Panel Header
The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:
The ATX 24-pin connector allows you to connect to ATX v2.x power supply.
With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX match perfectly.
Connecting 24-pin power cable
24-pin power cable
The ATX12V4P power connector is used to provide power to the CPU.
When installing 4-pin power cable, the latches of power cable and the ATX12V4P match perfectly.
Connecting 4-pin power cable
4-pin power cable
Chapter 2
28
Z97-PK USER MANUAL
This concludes Chapter 2. The next chapter covers the BIOS.
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-con­tact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momen­tary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.
Connect the case speaker cable to SPK.
6. SPK: Speaker header
Chapter 3
Z97-PK USER MANUAL
29
About the Setup Utility
The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s con­figuration status and provides you with options to set system parameters. The pa­rameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we rec­ommend that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
when changing the system configuration
when a configuration error is detected and you are prompted to make changes to the Setup Utility
when trying to resolve IRQ conflicts
when making changes to the Power Management configuration
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:
Press DEL to enter SETUP
Chapter 3
Using BIOS
Hard drives, diskette drives and peripherals
Video display type and display options
Password protection from unauthorized use
Power Management features
Chapter 3
Z97-PK USER MANUAL
30
Press the delete key to access BIOS Setup Utility.
Resetting the Default CMOS Values
When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.
Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.
Chapter 3
Z97-PK USER MANUAL
31
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for informa­tion.
Some options (marked with an icon ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY FUNCTION
 Scrolls through the items on a menu
+/-
Change Opt.
F2 Previous Value
F3 Optimized Defaults
F1 General Help
ESC Exits the current menu

Enter Select
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by an icon .
F4 Save & Exit
1. For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.
2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select item; Double click: enter; Right click: exit.
Chapter 3
Z97-PK USER MANUAL
32
Main Menu
System Date & Time
The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
System Language (English)
This item is used to set system language.
This menu shows the information of BIOS and enables you to set the system language, date and time.
Choose the system default language
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
BIOS Information
System Language English
System Date Tue 07/01/2014
System Time 00:27:45
Chapter 3
Z97-PK USER MANUAL
33
The Advanced menu items allow you to change the settings for the CPU and other system.
Advanced Menu
LAN Configuration Parameters
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
LAN Configuration
PC Health Status Power Management Setup ACPI Settings CPU Configuration SATA Configuration USB Configuration Trusted Computing Intel(R) Rapid Start Technology Intel(R) Smart Connect Technology
LAN Configuration
The item in the menu shows the LAN-related information that the BIOS automatically detects.
Onboard LAN Controller (Enabled)
Use this item to enable or disable Onboard LAN controller.
Press <Esc> to return to the Advanced Menu page.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
LAN Configuration
Onboard LAN Controller Enabled
Enabled/Disabled Onboard LAN Controller
Chapter 3
Z97-PK USER MANUAL
34
Smart Fan Mode (Normal)
This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.
PC Health Status
On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
Scroll to this item and press <Enter> to view the following screen:
Smart Fan Function
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
CPU Temperature (DTS) 46 System Temperature 31OC CPU Fan Speed 3426 RPM System Fan Speed 4787 RPM Core Voltage 1.728V DIMM Voltage 1.488V +12V 12.096V +5V 5.124V +3.3V 1.056V
TCC Activation Temperature (DTS) 75
Smart Fan Function
PC Health Status
Smart Fan Select
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Smart Fan Select CPU
Smart Fan Mode Normal Smart Fan start PWM value 180 Smart Fan start PWM TEMP(DTS) 45 DeltaT 3 Smart Fan Slope PWM value 10 Fan Full Speed Offset (DTS) 52
Smart Fan Select (CPU)
This item allows you to change and configure Smart Fans on M/B. ex. CPU Fan1, CPU Fan2, System Fan1.
Chapter 3
Z97-PK USER MANUAL
35
Smart Fan start PWM value (180)
Smart Fan start PWM TEMP (DTS) (45)
This item is used to set the start PWM value of the smart fan.
This item is used to set the start temperature of the smart fan.
DeltaT (3)
This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.
Smart Fan Slope PWM value (10)
This item is used to set the Slope Select PWM of the smart fan.
This item is used to set the CPU fan/System fan full speed offset value.
CPU Fan/System Fan Full Speed Offset (DTS) (52)
Press <Esc> to return to the PC Health Status page.
CPU Temperature (DTS)
System Temperature
CPU Fan Speed
System Fan Speed
Core Voltage
DIMM Voltage
+12V
+5V
+3.3V
System Component Characteristics
These items display the monitoring of the overall inboard hardware health events, such as CPU & DIMM voltage, CPU & System fan speed...etc.
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Z97-PK USER MANUAL
36
Power Management Setup
This page sets up some parameters for system power management operation.
Resume By PME (Disabled)
The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI/PCI-E Modem or PCI/PCI-E LAN c
ard. You must use an ATX power supply in order to use this
feature. Use this item to do wake-up action if inserting the PCI/PCI-E card.
Resume By USB (Disabled)
This item allows you to enable or disable the USB device wakeup function from S3 mode.
EUP Function (Enabled)
This item allows user to enable or disable EUP support.
Press <Esc> to return to the Advanced Menu page.
Power LED Type (Dual Color LED)
This item shows the type of the Power LED.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
About Resume By Ring
Resume By RTC Alarm (Disabled)
The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wake­up alarm. You must use an ATX power supply in order to use this feature.
Wake on LAN (Disabled)
Use this item to enable or disable integrated LAN to wake the system. (The wake on LAN cannot be disabled if ME is on at Sx state.) If disabled, resume by USB (S3) will not be available.
Resume By RING (Disabled)
An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state.
Power Management Setup
Resume By RING Disabled
Resume By PME Disabled Wake on LAN Disabled Resume By USB Disabled Resume By RTC Alarm Disabled EUP Function Enabled Power LED Type Dual Color LED
Chapter 3
Z97-PK USER MANUAL
37
ACPI Settings
The item in the menu shows the highest ACPI sleep state when the system enters suspend.
ACPI Sleep State [S3(Suspend to RAM)]
This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).
Press <Esc> to return to the Advanced Menu page.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.
ACPI Settings
ACPI Sleep State S3 (Suspend to RAM)
Chapter 3
Z97-PK USER MANUAL
38
CPU Configuration
The item in the menu shows the CPU.
Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz
This is display-only field and displays the information of the CPU installed in your comput
er.
EM64T (Supported)
This item shows the computer supports EM64T.
Processor Speed (2000MHz)
This item shows the current processor speed.
Processor Stepping (306c3)
This item shows the processor stepping version.
Microcode Revision (19)
This item shows the Microcode version.
Processor Cores (2)
This item shows the core number of the processor.
Intel HT Technology (Not Supported)
This item shows the computer not supports Intel HT Technology.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Number of cores to enable in each processor package.
CPU Configuration
Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz EM64T Supported Processor Speed 2000 MHz Processor Stepping 306c3 Microcode Revision 19 Processor Cores 2 Intel HT Technology Not Supported Intel VT-x Technology Supported
Active Processor Cores All
Limit CPUID Maximum Disabled Execute Disable Bit Enabled Intel Virtualization Technology Enabled LakeTiny Feature Enabled CPU C3 Report Enabled CPU C6 Report Enabled Package C State limit AUTO Enhanced Halt (C1E) Enabled
Active Processor Cores (All)
Use this item to control the number of active processor cores.
Limit CPUID Maximum (Disabled)
Use this item to enable or disable the maximum CPUID value limit, you can enables this item to prevent the system from “rebooting” when trying to install Windows NT
4.0.
Intel VT-x Technology (Supported)
This item shows the computer supports Intel VT-x Technology.
Chapter 3
Z97-PK USER MANUAL
39
Press <Esc> to return to the Advanced Menu page.
Execute Disable Bit (Enabled)
This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.
Intel Virtualization Technology (Enabled)
When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.
LakeTiny Feature (Enabled)
Use this item to enable or disable the LakeTiny for C state configuration.
CPU C6 Report (Disabled)
Use this item to enable or disable CPU C6 (ACPI C3) report to OS.
CPU C3 Report (Enabled)
Use this item to enable or disable CPU C3 (ACPI C2) report to OS.
Package C State limit (AUTO)
Use this item to set the package C state limit.
Enhanced Halt (C1E) (Enabled)
Use this item to enable or disable the Enhanced C1 state.
Chapter 3
Z97-PK USER MANUAL
40
SATA Configuration
Use this item to show the mode of serial SATA configuration options.
SATA Mode (AHCI Mode)
Use this it
em to select SATA mode.
Determines how SATA controller(s) operate.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Press <Esc> to return to the Advanced Menu page.
SATA Port 1~6 (Not Present)
This motherboard supports six SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.
Spin up Device (Disabled)
On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device.
External SATA (Disabled)
Use this item to enable/disable External SATA Support.
SATA Configuration
SATA Mode AHCI Mode
SA
TA Port1 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port2 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port3 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port4 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port5 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port6 Not Present Spin Up Device Disabled External SATA Disabled
Chapter 3
Z97-PK USER MANUAL
41
All USB Devices (Enabled)
Use this item to enable or disable all USB devices.
USB Configuration
Use this item to show the information of USB configuration.
Legacy USB Support (Enabled)
Use this item to enable or disable support for legacy USB devices.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
USB Support Parameters
USB Configuration
All USB Devices Enabled
Legacy USB Support Enabled
Press <Esc> to return to the Advanced Menu page.
Chapter 3
Z97-PK USER MANUAL
42
Trusted Computing
Use this item to show the information of trusted computing configuration.
Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
TPM Support (Enabled)
Use this item to enable or disable the TPM support. O.S. will not show TPM. Reset of platform is required.
Pending operation (None)
Schedule an Operation for the Security Device. NOTE: Your Computer will reboot during restart in order to change State of Security Device.
TPM State (Disabled)
Use this item to enable or disable the security device.
Press <Esc> to return to the Advanced Menu page.
TPM Active Status (Deactivated)
This item displays the TPM status to be activated or not.
TPM Enabled Status (Disabled)
This item displays the TPM status to be enabled or not.
TPM Owner Status (Unowned)
This item displays the TPM status to be owned or not.
Configuration
TPM Support Enabled
TPM State Disabled Pending operation None
Current Status Information TPM Enabled Status: Disabled TPM Active Status: Deactivated TPM Owner Status: Unowned
Chapter 3
Z97-PK USER MANUAL
43
Use this item to show the information of Intel(R) Rapid Start Technology.
Intel(R) Rapid Start Technology
Intel(R) Rapid Start Technology (Disabled)
Use this item to enable or disable the Intel(R) Rapid Start Technology.
Enable or disable Intel(R) Rapid Start Technology.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Intel(R) Rapid Start Technology Disabled
Press <Esc> to return to the Advanced Menu page.
Use this item to show the information of Intel(R) Smart Connect Technology.
Intel(R) Smart Connect Technology
ISCT Configuration (Disabled)
Use this item to enable or disable ISCT configuration.
Enable/Disable ISCT Configuration
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
ISCT Configuration Disabled
Chapter 3
Z97-PK USER MANUAL
44
The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system.
Chipset Menu
System Agent (SA) Parameters.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
System Agent Configuration
PCH Configuration ME Configuration
Chapter 3
Z97-PK USER MANUAL
45
IGD Memory (64M)
This item shows the information of the IGD (Internal Graphics Device) memory.
This item allows you to select graphics controller to use as the primary boot device.
DVMT Memory (256M)
When set to Fixed Mode, the graphics driver will reserve a fixed position of the
s
ystem memory as graphics memory, according to system and graphics
requirements.
Initiate Graphic Adapter (Auto)
System Agent Configuration
Scroll to this item and press <Enter> to view the following screen:
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select SG for Switchable Gfx.
System Agent Configuration
Initiate Graphic Adapter Auto
IGD Memory 64M DVMT Memory 256M IGD Multi-Monitor Disabled
CPU SA Audio Device Enabled
IGD Multi-Monitor (Disabled)
This item allows you to enable or disable the IGD Multi-Monitor.
CPU SA Audio Device (Enabled)
This item allows you to enable or disable the CPU SA Audio device.
Press <Esc> to return to the Chipset Menu page.
Chapter 3
Z97-PK USER MANUAL
46
Multi-Monitor technology
Please note that Multi-Monitor technology supports up to four monitors: one or two Intel integrated Graphics and one or two PCI-Express graphics devices under Windows 7/8.
Multi-Monitor technology can help you to increase the area available for programs running on a single computer system through using multiple display devices.
It is not only to increase larger screen viewing but aslo to improving personal productivity.
Step 1. Insert ECS drives DVD to run Auto setup or browse the DVD to install Intel chipset drivers, VGA and sound drivers.(If you want know the detail information, please refer to chapter 4.)
Intel Integrated Graphics
PCI-Express Graphics
Chapter 3
Z97-PK USER MANUAL
47
Step 3. Enable IGD Multi-Monitor from BIOS. In the following BIOS screen, please set
IGD Multi-Monitor to [Enabled].
Step 2. Install all the drivers of PCI-Express graphic cards. Click the Browse CD item,
then appears the following screen. Select the driver you want to install(e.g NVIDIA
GeForce 8400 GS(Microsoft Corporation-WDDM v1.1)) and double click it.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Select which of IGFX/PEG/PCI Graphics device should be Primary Display or Select SG for Switchable Gfx.
System Agent Configuration
Initiate Graphic Adapter Aut o
IGD Memory 64M DVMT Memory 256M IGD Multi-Monitor Enabled
CPU SA Audio Device Enabled
Chapter 3
Z97-PK USER MANUAL
48
2.Select display devices, set the multiple displays option and to extend destop for display “Multi-Monitor technology”.
Change the apprearance of your displays
Control Panel All Control Panel Items Display Screen Resolution
Search Control Panel
1
3
4
Detect
Identify
3. DELL U2410Display:
Resolution:
1920 x 1200 (recommended)
Orientation: Landscape
Disconnect this displayMultiple displays:
Make this my main display
Advance settings
Make text and other items larger or smaller What display settings should I choose?
OK Cancel Apply
2
You must select Apply before making additional changes.
!
Extend desktop to this display Disconnect this display
Step 4. Change the appearance of your displays under Windows 7/8.
Change the apprearance of your displays
Control Panel All Control Panel Items Display Screen Resolution
Search Control Panel
1
2
3
4
Detect
Identify
1. DELL U2410Display:
Resolution:
1920 x 1200 (recommended)
Orientation: Landscape
Extend desktop to this displayMultiple displays:
This is currently your main display.
Advance settings
Make text and other items larger or smaller What display settings should I choose?
OK Cancel Apply
Show the path of the setting location
Display devices
The type of the display
Set the multiple displays
1. Enter the Control Panel menu, select the Display in the All Control Panel Items and click the Screen Resolution, then appears the following screen.
Chapter 3
Z97-PK USER MANUAL
49
Change the apprearance of your displays
Control Panel All Control Panel Items Display Screen Resolution
Search Control Panel
1
Detect
Identify
4. AL1717Display:
Resolution:
1920 x 1200 (recommended)
Orientation: Landscape
Disconnect this displayMultiple displays:
Make this my main display
Advance settings
Make text and other items larger or smaller What display settings should I choose?
OK Cancel Apply
2
You must select Apply before making additional changes.
!
3
4
3
Change the apprearance of your displays
Control Panel All Control Panel Items Display Screen Resolution
Search Control Panel
1
Detect
Identify
4. AL1717Display:
Resolution:
1920 x 1200 (recommended)
Orientation: Landscape
Extend desktop to this displayMultiple displays:
Make this my main display
Advance settings
Make text and other items larger or smaller What display settings should I choose?
OK Cancel Apply
2
You must select Apply before making additional changes.
!
3
4
Chapter 3
Z97-PK USER MANUAL
50
PCH Configuration
Scroll to this item and press <Enter> to view the following screen:
Restore AC Power Loss (Power Off)
This item enables your computer to automatically restart or return to its operating status.
Azalia HD Audio (Enabled)
This item enables or disables Azalia HD audio.
Case Open Warning (Disabled)
This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case.
Chassis Opened (No)
This item indicates whether the case has been opened.
Press <Esc> to return to the Chipset Menu page.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Select AC Power state when Power is re-applied after a power failure.
PCH Configuration
Restore AC Power Loss Power Off
Audio Configuration Azalia HD Audio Enabled
Case Open Warning Disabled Chassis Opened No
Chapter 3
Z97-PK USER MANUAL
51
ME Configuration
Scroll to this item and press <Enter> to view the following screen:
ME Control (Enabled)
Use this item to enable or disable the ME Firmware.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Enable/Disable ME Firmware
Management Engine Technology Configuration
ME Control Enabled
ME FW Version
9.1.2.1010
ME FW Version (9.1.2.1010)
This item shows the ME FW version.
Press <Esc> to return to the Chipset Menu page.
Chapter 3
Z97-PK USER MANUAL
52
This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
M.I.B. III (MB Intelligent BIOS III) Menu
CPU Configuration
Scroll to this item to view the following screen:
+/- : Change Opt.
Enter/Dbl Click : Select

: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults
ESC/Right Click: Exit
F4: Save & Exit

Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
CPU OverClocking Configuration
M.I.B. III (MB Intelligent BIOS III)
CPU OverClocking Configuration Memory Configuration
North Bridge Configuration
Over Voltage Configuration
Spread Spectrum Auto
Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz Processor Speed 2000 MHz Memory Frequency 1333 MHz Total Memory 4096MB (DDR3 )
Main Advanced Chipset M.I.B. III Security Boot Exit
Non Turbo Ratio Override
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
CPU Ratio (32)
This item allows users to control non turbo CPU ratio.
Package Current Lock (Disabled)
This item allows you to enable or disable the package current lock.
CPU Ratio 32
Package Current Lock Disabled
IA Core Current Maximum
Enhanced Intel SpeedStep Technology Enabled
Turbo Mode Enabled
Runtime Turbo Enable Disabled
Internal PLL Overvoltage Disabled
Boot performance Mode Max Non-Turbo Perfor...
Package TDP Lock Enable Disabled
Long Duration Power Limit Override Maximum
Power Limit 1 Time(Second) 8
Power Limit 2 Switch Enabled
Short Duration Power Limit Override Maximum
1 Core Ratio Limit 32
2 Core Ratio Limit 32
Disable OverClocking Lock Enabled
ICC clock setting
Host Clock Override(1/100 MHz) 100.00
PEG/DMI Ratio 1.00
LCPLL or SBPLL select LCPLL
Chapter 3
Z97-PK USER MANUAL
53
Enhanced Intel SpeedStep Technology (Enabled)
This item allows users to enable or disable the EIST (Enhanced Intel SpeedStep Tech-
nology).
Turbo Mode (Enabled)
This item allows you to control the Intel Turbo Boost Technology.
1 /2 Core Ratio Limit (32)
These items show the Core Ratio Limit Value.
IA Core Current (Maximum)
This item allows you to set IA Core Current Max.
Boot performance Mode (Turbo Performance)
Use this item to select the performance state that the BIOS will set before OS handoff.
Package TDP Lock Enable (Disabled)
This item allows you to enable or disable the package TDP lock.
Long Duration Power Limit Override (Maximum)
Intel(R) Turbo Boost Technology will use this power limit during the long duration
pow
er limit time window.
Power Limit 1 Time(Second) (8)
This item allows you to set the power limit 1 time.
Power Limit 2 Switch (Enabled)
This item allows you to enable or disable the power limit 2 switch.
Disable OverClocking Lock (Enabled)
This item allows you to control the OverClocking lock.
Press <Esc> to return to the M.I.B. III Menu page.
Short Duration Power Limit Override (Maximum)
Intel(R) Turbo Boost Technology will use this power limit for a very short duration.
After that, the long duration power limit will be honored.
Runtime Turbo Enable (Disabled)
This item allows users to control non turbo CPU ratio.
Internal PLL Overvoltage (Disabled)
This item allows users to control the internal PLL overvoltage.
Host Clock Override(1/100 MHz) (100.00)
This item shows the informtion of the host clock override.
PEG/DMI Ratio (1.00)
This item shows the informtion of the PEG/DMI Ratio.
LCPLL or SBPLL select (LCPLL)
This item shows the informtion of the ICC clocking mode.
Chapter 3
Z97-PK USER MANUAL
54
Main Advanced Chipset M.I.B. III Security Boot Exit
The selection of Memory Profiles which impacts memory sizing behavior.
Memory Configuration
Scroll to this item to view the following screen:
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Memory Information
Memory RC Version 1.8.0.0 Memory Frequency 1333 Mhz Total Memory 4096 MB (DDR3)
Memory Profiles Automatic
Memory Frequency 1333 Timing Default Current Target tCL 9 9 9 tRCD 9 9 9 tRP 9 9 9 tRAS 24 24 24 NMode 1 1 Auto tWR 10 10 10 tRFC 107 107 107 tWTR 5 5 5 tRRD 4 4 4 tRTP 5 5 5 tCWL 7 7 7 tREFI 5200 5200 5200 tFAW 20 20 20 tRC 33 33 33 tWRPRE Auto tCPDED Auto tPRPDEN Auto OdtReadDelay Auto tCKE Auto tCCD Auto tWPRE Auto tRPRE Auto
Chapter 3
Z97-PK USER MANUAL
55
Mc Lock (Enabled)
This item allows you to enable or disable capacity to lock MC registers or not.
Memory RC Version (1.8.0.0)
This item shows the information of the memory RC version.
Memory Frequency (1333 Mhz)
This item shows the information of the memory frequency.
Total Memory (4096 MB (DDR3))
This item shows the information of the total memory.
Memory Profiles (Automatic)
This item enables you to set the memory profiles. The selection of memory profiles
impacts memory sizing beha
vior.
Main Advanced Chipset M.I.B. III Security Boot Exit
Enable or disable Refresh 2x support.
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
tRDRD Auto
tRDRD_dr Auto tRDRD_dd Auto tRDPDEN Auto CMD_3st Auto tWRRD Auto tWRRD_dr Auto tWRRD_dd Auto tWRWR Auto tWRWR_dr Auto tWRWR_dd Auto tWRPDEN Auto Dec_WRD Auto
Enh Interleave Support Enabled RI Support Enabled OLL Weak Lock Support Enabled Mc Lock Enabled CMD Tri-State Enabled Memory Scrambler Enabled MRC Fast Boot Enabled Memory Remap Enabled Memory Thermal Management Enabled DDR PowerDown and idle counter BIOS
Refresh 2x Support Disabled
Enh Interleave Support (Enabled)
This item allows you to enable or disable the Enh Interleave support.
RI Support (Enabled)
This item allows you to enable or disable the Rank Interleave support. NOTE: RI
and HORI can not be enabled at the same time.
DLL Weak Lock Support (Enabled)
This item allows you to enable or disable the DLL weak lock support.
Chapter 3
Z97-PK USER MANUAL
56
CMD Tri-State (Enabled)
This item allows you to enable or disable the CMD Tri-State (ending of the training).
Memory Scrambler (Enabled)
This item allows you to enable or disable the memory scrambler.
WRC Fast Boot (Enabled)
This item allows you to enable or disable the WRC fast boot.
Memory Remap (Enabled)
This item allows you to enable or disable the memory remap above 4G.
Memory Thermal Management (Enabled)
This item allows you to enable or disable the memory thermal management.
DDR PowerDown and Idle counter (BIOS)
This item allows you to BIOS or PCODE the DDR Power Down and Idle counter. BIOS:
BIOS is in countrol of DDR CKE mode and idle timer value. PCODE: pcode will manage the modes.
Refresh 2x Support (Disabled)
This item allows you to enable or disable 2xRef when warm and Hot 2-iMC enables
2xRef when Hot.
Press <Esc> to return to the M.I.B. III Menu page.
Chapter 3
Z97-PK USER MANUAL
57
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Graphics Core Ratio Limit (22)
This item allows you to control the internal GFX core ratio.
Press <Esc> to return to the M.I.B. III Menu page.
North Bridge Configuration
Scroll to this item to view the following screen:
Graphics Core Ratio Limit
Intel Graphics Configuration
Graphics Core Ratio Limit 22
Chapter 3
Z97-PK USER MANUAL
58
Over Voltage Configuration
Scroll to this item to view the following screen:
PCH Core Voltage 1.056 V (Auto)
This item allows you to adjust the PCH Core voltage.
DIMM Voltage 1.488 V (Auto)
This item allows you to adjust the DIMM voltage.
Processor Input Voltage (Auto)
This item allows you to adjust the processor input voltage.
Vdroop (Enabled)
Use this item to enable or disable the Vdroop.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
PCH Core Voltage 1.056 V Auto
DIMM Voltage 1.500 V Auto Processor Input Voltage Auto Vdroop Enabled
CPU Adaptive Voltage Target(mV) 0 CPU Voltage Mode Adaptive CPU Voltage Offset(mV) 0 Offset Preflx +
RING Adaptive Voltage Target(mV) 0 RINGVoltage Mode Adaptive RING Voltage Offset(mV) 0 Offset Prefix +
SVID Control Enable Enabled SVID Override Voltage Target(mV) 0
FIVR Faults Enable Enabled FIVR Efficiency Enable Enabled
GT Adaptive Voltage Target(mV) 0 GT Voltage Mode Adaptive GT Voltage Offset (mV) 0 Offset Prefix -
UNCORE Voltage Offset (mV) 0 Offset Prefix +
IOA Voltage Offset (mV) 0 Offset Prefix +
IOD Voltage Offset (mV) 0
CPU/RING/GT Adaptive Voltage Target(mV) (0)
This item allows you to adjust the CPU/RING/GT Adaptive voltage target from 0 to 2000mV.
Chapter 3
Z97-PK USER MANUAL
59
CPU/RING/GT Voltage Mode (Adaptive)
This item allows you to set the CPU/RING/GT voltage mode.
CPU/RING/GT/UNCORE/IOA/IOD Voltage Offset(mV) (0)
This item allows you to adjust the CPU/RING/GT/UNCORE/IOA/IOD voltage offset from
-1000 to 998mV.
Offset Prefix (+)
This item allows you to select the offset value as positive (+) or negative (-).
SVID Control Enable (Enabled)
This item allows you to enable or disable the SVID control. If this function be
disabled, it will not be changed until CPU powers down.
SVID Override Voltage Target(mV) (0)
This item allows you to adjust the SVID override voltage target, up to 2500mV.
FIVR Faults Enable (Enabled)
This item allows you to enable or disable the FIVR faults. If this function is disabled,
it will not be changed until CPU powers down.
FIVR Efficiency Enable (Enabled)
This it
em allows you to enable or disable the FIVR efficiency. If this function is
disabled, it will not be changed until CPU powers down.
Press <Esc> to return to the M.I.B. III Menu page.
Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz
This is display-only field and displays the information of the CPU installed in your
c
omputer.
Processor Speed (2000 MHz)
This item shows the CPU speed.
Memory Frequency (1333 MHz)
This item shows the memory frequency.
Total Memory (4096 MB (DDR3))
This item shows the total memory.
Spread Spectrum (Auto)
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic
Interference) generated by the system.
Chapter 3
Z97-PK USER MANUAL
60
This page enables you to set setup administrator password and user password.
Security Menu
Administrator Password Status (Not Install)
This item shows administrator password installed or not.
User Password Status (Not Install)
This item shows user password installed or not.
Secure Boot (Disabled)
This item is used to control the secure boot flow, it is possible only if system runs in User Mode.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Set Administrator Password
System Mode state Setup Secure Boot state Not Active
Secure Boot Disabled
Administrator Password
Administrator Password Status Not Install User Password Status Not Install
System Mode state (Setup)
This item shows system mode setup or not.
Secure Boot state (Not Active)
This item allows you to enable or disable the secure boot state.
Chapter 3
Z97-PK USER MANUAL
61
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
This page enables you to set the keyboard NumLock state.
Boot Menu
Boot Configuration
This item shows the information of the Boot Configuration.
Operation System Select (Windows 7 or other OS)
This item is used to select the operation system.
Launch PXE OpROM (Disabled)
The item enables or disables launch PXE Option ROM.
Launch Storage OpROM (Enabled)
Use this item to enable or disable the Storage OpROM.
Fast Boot (Disabled)
This item enables or disables boot with initialization of a minimal set of device re-
quired to launch active boot option. Has no effect for BBS boot options.
Bootup NumLock State (On)
This item enables you to select NumLock state.
Quiet Boot (Enabled)
This item enables or disables quiet boot.
Update System BIOS (Disabled)
This item enables or disables to update system BIOS.
Boot mode select (LEGACY)
Use this item to select boot mode.
Set Boot Priority
This item enables you to set boot priority for all boot devices.
Boot Option #1 /
2 /3 /4 /5 /6 /7
These items show the boot priorities.
Windows 7 or other OS: Boot policy for Legacy OS.
Windows 8: Boot policy for UEFI OS without Compatibility Support Module(CSM).
Manual: User customized CSM parameters & boot policy.
Boot Configuration
Operation System Select Windows 7 or other OS
Launch PXE OpROM Disabled Launch Strorage OpROM Enabled
Fast Boot Disabled
Bootup NumLock State On Quiet Boot Enabled Update System BIOS Disabled Boot mode select LEGACY
FIXED BOOT ORDER Priorities Boot Option #1 Hard Disk Boot Option #2 CD/DVD Boot Option #3 USB Floppy Boot Option #4 USB CD/DVD Boot Option #5 USB Hard Disk Boot Option #6 USB Key Boot Option #7 Network
Chapter 3
Z97-PK USER MANUAL
62
Boot Override
Use this item to select the boot device.
Save Options
This item enables you to save the options that you have made.
Save Changes
This item enables you to save the changes that you have made.
Discard Changes
This item enables you to discard any changes that you have made.
Restore Defaults
This item enables you to restore defaults to all the setup options.
Discard Changes and Exit
This item enables you to exit system setup without saving any changes.
Discard Changes and Reset
This item enables you to reset system setup without saving any changes.
This page enables you to exit system setup after saving or without saving the changes.
Exit Menu
Save Changes and Exit
This item enables you to exit
t the system setup after saving the changes.
Save Changes and Reset
This item enables you to reset system setup after saving the changes.
Main Advanced Chipset M.I.B. III Security Boot Exit
Go back to EZ Mode
Back to EZ Mode
Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset
Save Options Save Changes Discard Changes
Restore Defaults
Boot Override
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Back to EZ Mode
This item enables you to back to EZ mode.
Chapter 3
Z97-PK USER MANUAL
63
Updating the BIOS
You can download and install updated BIOS for this motherboard from the
manufacturer’s Website. New BIOS provides support for new peripherals, improve-
ments in performance, or fixes for known bugs. Install new BIOS as follows:
This concludes Chapter 3. Refer to the next chapter for information on the software
supplied with the motherboard.
1 If your motherboard has a BIOS protection jumper, change the setting to
allow BIOS flashing.
2 If your motherboard has an item called Firmware Write Protect in
Advanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)
3 Prepare a bootable device or create a bootable system disk. (Refer to
Windows online help for information on creating a bootable system disk.)
4 Download the Flash Utility and new BIOS file from the manufacturer’s
Web site. Copy these files to the bootable device.
5 Turn off your computer and insert the bootable device in your computer.
(You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)
6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file
name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE
040706.ROM
7 When the installation is complete, remove the bootable device from the
computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.
Chapter 3
Z97-PK USER MANUAL
64
Memo
65
Z97-PK USER MANUAL
Chapter 4
Chapter 4
Using the Motherboard Software
The auto-install DVD-ROM makes it easy for you to install the drivers and software.
The support software DVD-ROM disc loads automatically under Windows XP/7/8.
When you insert the DVD-ROM disc in the DVD-ROM drive, the auto-run feature will
automatically bring up the installation screen. The screen has four buttons on it:
Setup, Utilities, Browse CD and Exit.
Auto-installing under Windows XP/7/8
Displays the path for all software and drivers available on the disk.
Open Windows Explorer and show the contents of the support disk.
Click “Exit” button to close the Auto-Setup
window.
Browse CD:
Click the “Setup” button to select and run the software installation program.
Click the “ Utilities” button to select and install ECS Intelligent Utility.
Information:
Follow these instructions to install device drivers and software for the
motherboard:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.
1. Click Setup. The installation program begins:
Running Setup
The motherboard identification is located in the upper left-hand corner.
66
Z97-PK USER MANUAL
Chapter 4
2. Click Next. The following screen appears:
3. Check the box next to the items you want to install. The default options are recommended.
5. Follow the instructions on the screen to install the items.
4. Click Next to run the Installation Wizard. An item installation screen appears:
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to re­start a few times to complete the installation.
Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver.
67
Z97-PK USER MANUAL
Chapter 4
If the auto-install DVD-ROM does not work on your system, you can still install
drivers through the file manager for your OS (for example, Windows Explorer). Look
for the chipset and motherboard model, and then browse to the directory and path
to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that
automatically detects your operating system before installation. Other drivers have
the setup program located in the operating system subfolder.
Manual Installation
ECS Utility Software (Intelligent EZ Utility)
ECS Intelligent EZ Utility provides friendly interfaces under Windows O.S, which makes
your computing more easily and conveniently.
If the driver you want to install does not have a setup program, browse to the oper-
ating system subfolder and locate the readme text file (README.TXT or README.DOC)
for information on installing the driver or software for your operating system.
These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software.
Windows 7/8 will appear below UAC (User Account Control) message after the system restart. You must select “Yes” to install the next driver. Continue
this process to complete the drivers installation.
68
Z97-PK USER MANUAL
Chapter 4
eBLU
ECS eBLU utility makes BIOS update faster and easier. eBLU will list the latest BIOS with a default check-mark. Click”install” button to install.
eDLU
ECS eDLU utility makes updating drivers fast and easy. eDLU saves time and hassle by listing all the latest drivers online. Just select the one you prefer and start to download and install the drivers.
eSF
eSF(Smart Fan) utility provides easy and safe way to adjust fan speed in accordance with your PC’s system loading and temperature.
It has five modes to adjust fan speed in a safe range without entering the BIOS to optimize your system cooling environment.
Microsoft .NET Framework 3.5 is required.
Microsoft .NET Framework 3.5 is required.
69
Z97-PK USER MANUAL
Chapter 5
Chapter 5
Intel® Rapid Storage Technology RAID Configuration
The Intel® Rapid Storage Technology allows you to configure RAID 0, and 1 sets on the
external Serial ATA hard disk drives.
1. Install the external Serial ATA hard disk drive (HDD) on your system.
2. Set the SATA Mode item in the BIOS from “IDE Mode” to “RAID Mode”
See section “SATA Configuration” for details.
Before creating a RAID set
1. One SATA HDD.
2. A write-enabled floppy disk.
3. Microsoft
®
Windows® OS installation disk (Windows 7/8/8.1).
4. Motherboard support CD with Intel® Rapid Storage Technology RAID driver.
Complete the following steps before you create a RAID set:
Prepare the following items:
Determines how SATA controller(s) operate.
Main Advanced Chipset M.I.B. III Security Boot Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
SATA Configuration
SATA Mode AHCI Mode
SATA Port1 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port2 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port3 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port4 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port5 Not Present Spin Up Device Disabled External SATA Disabled
SATA Port6 Not Present Spin Up Device Disabled External SATA Disabled
70
Z97-PK USER MANUAL
Chapter 5
2. The main Intel® Rapid Storage Technology RAID BIOS menu appears.
Entering Intel® Rapid Storage Technology RAID BIOS utility
1. During POST, press <Ctrl-I> to enter the Intel® Rapid Storage Technology RAID BIOS menu.
3. Use the arrow keys to move the color bar and navigate through the items.
3. Enter the Intel
®
Rapid Storage Technology option to set up your RAID
configuration.
4. Create an Intel
®
Rapid Storage Technology RAID driver disk for Windows
®
OS installation. See section “Creating a RAID driver disk” for details.
5. Install the Intel
®
Rapid Storage Technology RAID driver after the Windows
®
OS had been installed.
Intel(R) Matrix Storage Manager option ROM 11.0.0.1204 Copyright(C) 2003-07 Intel Corporation. All Rights Reserved.
RAID Volumes:
None defined.
Physical Disks: Port Drive Model Serial # Size Type/Status(Vol ID)
4 Maxtor 7H500F0 H81D3FLH 465.8GB Non-RAID Disk 5 ST3500320AS 5QM0KLEY 465.8GB Non-RAID Disk
Press <CTRL-I> to enter Configuration Utility...
[ Main Menu ]
1. Create RAID Volume 4. Recovery Volume Options
2. Delete RAID Volume 5. Acceleration Options
3. Reset Disks to Non-RAID 6. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
None defined.
Physical Devices: ID Device Model Serial # Size Type/Status (Vol ID)
2 WDC WD2001FASS-0 WD-WMAUR0083571 1.8TB Non-RAID Disk 3 SAMSUNG HD203WI S1UYJ1BZ203313 1.8TB Non-RAID Disk
[ ]-Select [ESC]-Exit [ENTER]-Select Menu
Intel(R) Rapid Storage Technology-Option ROM - 11.0.0.1204 Copyright(C) 2003-11 Intel Corporation. All Rights Reserved.
71
Z97-PK USER MANUAL
Chapter 5
2. When the RAID Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create.
Creating a RAID set
1. In the main Intel® Rapid Storage Technology RAID BIOS menu, highlight Create RAID Volume using the up/down arrow key then press <Enter>.
3. Key in the RAID volume capacity. Use the up/down arrow to choose the Capacity. The default value indicates the maximum capacity using the selected disks. Entering a lower capacity allows you to create a second volume on these disks.
When more than two HDDs are installed in your computer, the Disks item will be selectable. Then users can select the HDD that you want to belong to the RAID set. Please be noticed that selecting a wrong disk will result in losing the original data of the HDD.
[ Main Menu ]
1. Create RAID Volume 4. Recovery Volume Options
2. Delete RAID Volume 5. Acceleration Options
3. Reset Disks to Non-RAID 6. Exit
[ CREATE VOLUME MENU ]
Name: Volume0 RAID Level: RAID0(Stripe) Disks: Select Disks Strip Size: 128KB Capacity: 931.5 GB
Create Volume
[ CREATE VOLUME MENU ]
Name: Volume0 RAID Level: RAID1(Mirror) Disks: Select Disks Strip Size: N/A Capacity: 465.8 GB
Create Volume
[ CREATE VOLUME MENU ]
Name: Volume0 RAID Level: RAID0(Stripe) Disks: Select Disks Strip Size: 128KB Capacity: 931.5 GB
Create Volume
[ CREATE VOLUME MENU ]
Name: Volume0 RAID Level: RAID0(Stripe) Disks: Select Disks Strip Size: 128KB Capacity: 931.5 GB
Create Volume
72
Z97-PK USER MANUAL
Chapter 5
Pressing <Y> deletes all the data in the HDDs.
5. The following screen appears, displaying the relevant information about the RAID set you created.
Users please be noted that RAID 0 (Stripe) is set to accelerate the data access, and RAID 1 (Mirror) is set to provide the data backup. If you want to set RAID 0, you need to set the 2nd Boot Device item in the BIOS to Intel Volume0. See section “Advanced Setup” for details.
4. When done, press <Enter> to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.
[ CREATE VOLUME MENU ]
Name: Volume0 RAID Level: RAID0(Stripe) Disks: Select Disks Strip Size: 128KB Capacity: 931.5 GB
[ ]Change [TAB]-Next [ESC]-Previous Menu [ENTER]-Select
Intel(R) Matrix Storage Manager option ROM 11.0.0.1204
Copyright(C) 2003-07 Intel Corporation. All Rights Reserved.
Press ENTER to create the specified volume.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
[ DISK/VOLUME INFORMATION ]
RAID Volumes: ID Name Level Strip Size Status Bootable
0 Volume0 RAID0(Stripe) 128KB 931.5GB Normal Yes
Physical Disks: Port Drive Model Serial # Size Type/Status (Vol ID)
4 Maxtor 7H500F0 H81D3FLH 465.8GB Member Disk(0) 5 ST3500320AS 5QM0KLEY 465.8GB Member Disk(0)
73
Z97-PK USER MANUAL
Chapter 5
Deleting a RAID set
1. In the main Intel® Rapid Storage Technology RAID BIOS menu, highlight Delete RAID Volume using the up/down arrow key then press <Enter>.
2. Use the space bar to select the RAID set you want to delete.
Press the <Del> key to delete the set.
3. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.
Pressing <Y> deletes all the data in the HDDs.
[ Main Menu ]
1. Create RAID Volume 4. Recovery Volume Options
2. Delete RAID Volume 5. Acceleration Options
3. Reset Disks to Non-RAID 6. Exit
[ CREATE VOLUME MENU ]
Name Level Drives Capacity Status Bootable
Volume0 RAID0(Stripe) 2 931.5GB Normal Yes
[ ]Select [ESC]-Previous Menu [DEL]-Delete Volume
Intel(R) Matrix Storage Manager option ROM 11.0.0.1204
Copyright(C) 2003-07 Intel Corporation. All Rights Reserved.
Deleting a volume will reset the disks to non-RAID.
WARNING: ALL DISK DATA WILL BE DELETED.
ALL DATA IN THE VOLUME WILL BE LOST!
Are you sure you want to delete “Volume0”? (Y/N):
[ DELETE VOLUME VERIFICATION ]
Main Advanced Chipset M.I.B. III Boot Security Exit
+/- : Change Opt.
Enter/Dbl Click : Select


: Select Screen
/Click: Select Item
F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit
Sets the system boot order
Hard Disk Drive Priorities
1st Boot Intel volume0
74
Z97-PK USER MANUAL
Chapter 5
Resetting disks to Non-RAID
An HDD that has been previously configured as part of another RAID set
in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this disk when configuring a RAID set through the Intel
®
Rapid Storage Technology option. If you still want to use this
broken RAID HDD as part of the RAID set configured through the Intel
®
Rapid Storage Technology, you may do so by resetting the disk to Non­RAID. You will, however, lose all data and previous RAID configurations.
To reset disks to Non-RAID:
1. In the main Intel® Rapid Storage Technology RAID BIOS menu, highlight Reset Disks to Non-RAID using the up/down arrow key then press <Enter>.
2. Use the space bar to select the HDD to reset to Non-RAID.
3. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.
Pressing <Y> deletes all the data in the HDDs.
When you have finished, highlight Exit using the up/down arrow key then press <Enter> to exit the Intel® Rapid Storage Technology RAID BIOS utility.
A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N> to return to the Intel
®
Rapid Storage Technology RAID BIOS menu.
Exiting Setup
[ Main Menu ]
1. Create RAID Volume 4. Recovery Volume Options
2. Delete RAID Volume 5. Acceleration Options
3. Reset Disks to Non-RAID 6. Exit
75
Z97-PK USER MANUAL
Chapter 6
Chapter 6
AMD CrossFireXTM Technology Support
This motherboard supports the AMD CrossFireX
TM
Technology that allows you to install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section.
Requirements
1 Two identical CrossFireXTM ready graphic cards are needed for the setup
of 2-way CrossFireX
TM
configuration.
2 You would need one CrossfireX
TM
bridge cable.
3 Make sure that your graphics card driver supports the AMD CrossFireX
TM
technology. Download the latest driver from the AMD website (www.amd.com).
4 Make sure that your power supply unit (PSU) can provide at least the mini-
mum power required by your system.
Installing CrossFireXTM graphics cards
1. Insert the CrossFireX
TM
graphics cards into the PCIEX16/PCIEX16_S1 slots. Make
sure that the card is properly seated on the slot.
* For reference only
3. Connect an auxiliary power source from the power supply to the graphics cards.
2. Connect the cable from your monitors to the CrossFireX
TM
ready graphics card
installed on the PCIE16X slot.
Monitor Cable
76
Z97-PK USER MANUAL
Chapter 6
The CatalystTM Control Center Dialog Box
To enable CrossFireXTM:
Install AMD graphic card driver.
Enter the Catalyst Control Center Dialog Box.
check the “Enable CrossFireX
TM
” item.
Click Apply button.
77
Z97-PK USER MANUAL
Chapter 7
Chapter 7
Trouble Shooting
Start up problems during assembly
After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. You may also log onto our ECS website for more information:
a) System does not power up and the fans are not running.
1. Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Make sure the power cord is plugged into the wall socket & the switch on the Power Supply Unit (PSU) is turned “ on “ as well. Turn on again to see if the CPU and power supply fans are running.
2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.
3. Check the CPU FAN connector is connected to the motherboard.
4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.
5. Check the 12V power connector is connected to the motherboard.
6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.
b) Power is on, fans are running but there is no display
1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.
2. Check the VGA adapter card (if applicable) is inserted properly.
3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps: memory not detected b. 1 long beep and 8 short beeps: VGA not detected
c) The PC suddenly shuts down while booting up.
1. The CPU may experience overheating so it will shutdown to protect itself. Apply the thermal grease onto the CPU heatsink & ensure the CPU fan is well-connected with the CPU heatsink. Check if the CPU fan is working properly while the system is running.
http:// www.ecs.com.tw/ECSWebSite/Support/Support_FAQ.aspx?MenulD=49& childid=M 49&LanlD=0
78
Z97-PK USER MANUAL
Chapter 7
Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.
1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.
2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and
Start up problems after prolong use
After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.
1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.
2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.
3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.
4. Remove the hard drive, optical drive or DDR memory to determine which of these components may be at fault.
areas of high moisture content.
3. Routinely clean the CPU cooler fan to remove dust and hair.
4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.
5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.
6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.
Maintenance and care tips
2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.
5. Check whether there is any bulked up electrolytic capacitor or abnormal component.
Please logo onto our ECS website: http://www.ecs.com.tw/ECSWebSite/Support/ Technical_Support_List.aspx?MenuID=50&LanID=0 for more information.
uB rewoP
desserp si no
.trats ot sliaf CP tub
seY
ylppuS rewoP fi kcehC
tinU
gnikrow si )USP(
oN
oN
dnuos peeB ynA
oN
kcehc dna SOMC RLC
rewop V21 UPC fi
detcennoc si
CP eht tratseR
?draob ro USP htiw melborP
AMR tcatnoc >- melborp draob fI
deulp si droc rewop CA gg
?no denrut si hctiws USP dna
seY
melborp draoB
AMR tcatnoc >-
oN
:speeb trohs 3 fI -
ylreporp ton yromem MMID
eruliaf yromem ro detresni
:speeb trohs 8 dna peeb gnol 1 fI -
detceted ton AGV
seY
seY
neercs TSOP ta tlaH
seY
OMC RL dna SC tser .tra
AMR tcatnoc ,liaf fI
seY
oN
eussi ecived larehpireP
.melborp DDH-
,rorre putes SOMC-
d .SOMCRLC ot een
ts ot liaf metsyS elbatsnu ro tra
a
es SOIB yfidom re
.gn
M SOC RLC tratser dna
hctiws USP no nruT
tekcos llaw ot tcennoc ro
.tratser dna
oN
h rotinom fi kcehC sa
sid
yalp
rotinom fi kcehC
yalpsid sah
Basic Troubleshooting Flowchart
79
80
Z97-PK USER MANUAL
Chapter 7
Memo
Loading...