ECS P67H2-A User Manual

Page 1

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.

Other product names used in this manual are the properties of their respective owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

Preface

Page 2

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1 Introducing the Motherboard

Chapter 2 Installing the Motherboard

Chapter 3 Using BIOS

Chapter 4 Using the Motherboard Software

Chapter 5 ATI CrossfireTM Technology Support

Chapter 6 Hydra Core Technology Support

Chapter 7 Setting Up eJIFFY

Chapter 8

® ®

Intel

Matrix Storage Manager RAID

Configurations

Describes features of the motherboard

Go to

Describes installation of motherboard components

Go to

Provides information on using the BIOS Setup Utility

Go to

Describes the motherboard software

Go to

Describes the ATI Crossfire Technology

Go to

Describes the Hydra Core Technology

Go to

Describes the eJIFFY setting up

Go to

Describes the Intel age Manager RAID Configurations

Go to

page 1

page 7

page 25

page 53

page 57

page 61

page 65

®®

Matrix Stor-

page 77

Preface

Page 3

iii

Chapter 9 Marvell 88SE9128 SATA 6Gb/s RAID

Controller BIOS Setup

Chapter 10 Provides basic trouble shooting Trouble Shooting

Describes the SATA RAID Setup

Go to

tips

Go to

page 83

page 89

Preface

Page 4

Memo

Preface

Page 5

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

ABLE OF CONTENTSABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...................................................................................1

Feature............................................................................................2

Specifications................................................................................4

Motherboard Components..........................................................5

Chapter 2

Installing the Motherboard 7

Safety Precautions............................................................................7

Choosing a Computer Case.............................................................7

Installing the Motherboard in a Case............................................7

Installing Hardware.............................................................................9

Installing the Processor............................................................9

Installing Memory Modules....................................................11

Expansion Slots.......................................................................13

Connecting Optional Devices.................................................15

Installing a SATA Hard Drive.................................................18

Connecting I/O Devices................................................................ 19

Connecting Case Components.......................................................20

Panel Header..........................................................................23

Chapter 3 25

Using BIOS 25

About the Setup Utility................................................................. 25

The Standard Configuration.......................... ........................25

Entering the Setup Utilities......................................................25

Resetting the Default CMOS Values....................................26

Using BIOS......................................................................................26

BIOS Navigation Key.............................................................27

Main Menu.............................................................................27

Advanced Menu......................................................................28

Chipset Menu..........................................................................41

M.I.B.X(MB Intelligent Bios X) Menu.....................................44

Boot Menu...............................................................................48

Page 6

Security Menu.........................................................................49

Save & Exit Menu...................................................................50

Updating the BIOS..................................................................52

Chapter 4

Using the Motherboard Software 53

About the Software DVD-ROM/CD-ROM...................................53

Auto-installing under Windows XP/Vista/7..................................53

Running Setup.........................................................................54

Manual Installation...........................................................................56

Utility Software Reference.................................................................56

Chapter 5

ATI CrossFireTM Technology Support 57

Requirements..................................................................................57

Installing CrossFireTM graphics cards.........................................57

The CatalystTM Control Center Dialog Box.................................59

To Enable CrossFireTM...........................................................59

Chapter 6

Hydra Core Technology Support 61

Requirements..................................................................................61

Installing graphics cards...............................................................61

The HYDRALOGIX Control Panel.................................................64

To Enable HydraLogix...........................................................64

Chapter 7

Setting Up eJIFFY 65

Introduction.................................................................................... 65

Installation and BIOS Setup..........................................................66

Entering eJIFFY....................................................................................69

Features Icons.....................................................................................70

Usage FAQ...........................................................................................71

53 53

57 57

61 61

65 65

Chapter 8

Intel® Matrix Storage Manager RAID Configurations 77

Before creating a RAID set............................................................77

Entering Intel® Matrix Storage Manager RAID BIOS utility....78

Creating a RAID set........................................................................79

Deleting a RAID set........................................................................81

Resetting disks to Non-RAID.......................................................82

Exiting Setup....................................................................................82

7777

Page 7

vii

Chapter 9

Marvell 88SE9128 SAT A 6Gb/s RAID Controller BIOS Setup 83

To Create Virtual Disks....................................................................83

Chapter 10

T r ouble Shooting 89

Start up problems during assembly..............................................89

Start up problems after prolong use............................................90

Maintenance and care tips..............................................................90

Basic Troubleshooting Flowchart...................................................91

83 83

89 89

Page 8

viii

Page 9

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing P67H2-A motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1155 socket for 2nd Generation Intel® CoreTM Family & Unlock processors to reach the optimum system performance. Combined with ECS unique M.I.B X* BIOS interface, it makes a simple, fast and safe O.C platform for high-end business or personal desktop market.

This motherboard is based on Intel® P67 Chipset for best desktop platform solution. P67 is a single-chip, highly integrated, high performance Hyper-Threading peripheral controller, unmatched by any other single chip-device controller. This motherboard supports up to 16 GB of system memory with dual channel DDR3

2133(OC)/1866(OC)/1600(OC)/1333/1066 SDRAM. It cooperates with LT24102

chips to generate three of PCIe 16X Gen 2 graphic interface, that allows you install up to three non-identical graphic cards with multiple GPU running at PCIe Gen 2 speed. It provides two PCI rev 2.3 slots and two PCI Express x1 rev 2.0 slots for extending usage. It implements an EHCI compliant interface that provides fourteen USB 2.0 ports (six USB ports and four USB 2.0 headers support additional eight USB ports and one of Front USB 2.0 headers provide with EZ charger technology, please reference chapter 2 parts of Front Panel USB headers to check the detail information). P67H2-A implements extra USB 3.0 chips which provide four USB3.0 ports at rear I/O with blue connector and one USB 3.0 header at internal I/O also.

P67H-A implements extra Marvell 88SE9128 SATA 6Gb/s chips, which provide two eSATA 6Gb/s ports with RAID 0, 1 configuration, this motherboard delivers the highest data transfer rate to fulfill the most speed-demanding usage.

The motherboard is equipped with advanced full set of I/O ports in the rear panel, including one PS/2 mouse and keyboard combo connector, one CLR_CMOS button, two eSATA 6Gb/s ports, two Gigabit LAN ports, six USB 2.0 ports, four USB 3.0 ports running at 5 Gb/s, one optical SPDIFO port and audio jacks for microphone, line-in and 8-ch line-out.

In addition, this motherboard comes with a power button and a reset button.

* ECS M.I.B X stands for extreme O.C BIOS interface. Please refer to chapter 3 for detailed setup information.

Introducing the Motherboard

Page 10

Feature

Processor

The motherboard uses an LGA1155 type of socket that carries the following features:

• Accommodates 2nd Generation Intel® CoreTM Family & Unlock processors

• Supports “Hyper-Threading” technology CPU

“Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical” processors within the same physical processor.

Chipset

The Intel® P67 Chipset is a single-chip with proven reliability and performance.

• Supports PCI Express x16 Gen2 slot

• Compliant with PCI Rev 2.3 interface

• Supports two PCI Express x1 Gen2 slot

• Supports two PCI slots

• Integrated four SATA 3.0 Gb/s Host Controllers and two SATA 6.0 Gb/ s Host Controller

• Fourteen USB 2.0 ports supported

• Four USB 3.0 ports and one USB 3.0 header supported(by NEC chip)

• Serial Peripheral Interface (SPI) support

• Enhanced DMA Controller, interrupt controller, and timer functions

• Intel® High Definition Audio Controller

Memory

• Supports DDR3 1333/1066 DDR3 SDRAM with Dual-channel architecture

• Accommodates four unbuffered DIMMs

• Up to 4 GB per DIMM with maximum memory size up to 16 GB

Audio

• 7.1+2 Channel High Definition Audio Codec

• Meets Microsoft WLP3.x (Windows Logo Program) audio

• All DACs supports 44.1k/48k/96k/192kHz sample rate

• Software selectable 2.5V/3.2V/4.0V VREFOUT

• Direct Sound 3D. compatible

• Power Support: Digital: 3.3V; Analog: 5.0V

requirements

Giga LAN

• Supports PCI Express

• Integrated 10/100/1000 transceiver

• Wake-on-LAN and remote wake-up support

1.1

Introducing the Motherboard

Page 11

Expansion Options

The motherboard comes with the following expansion options:

• Three PCI Express x16 slots for Graphic Interface (x16, x8, x8) or (x16, x16)

• Two PCI Express x1 slots

• Two 32-bit PCI v2.3 compliant slots

• Six 7-pin SATA connectors

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• One CLR_COMS button

• Two LAN ports

• Six USB 2.0 ports

• Four USB 3.0 ports

• Two eSATA ports

• One optical SPDIFO port

• Audio jacks for microphone, line-in and 8-ch line-out

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different processor clock speeds.

1. Some hardware specifications and software items are subject to change without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50 °C.

Introducing the Motherboard

Page 12

Specifications

CPU

Chipset

Memory

Expansion Slots

Storage

Audio

Giga LAN

Rear Panel I/O

Internal I/O Connectors & Headers

System BIOS

Form Factor • ATX Size, 305mm x 244mm

• LGA1155 socket for 2nd Generation Intel® CoreTM Family & Unlock processors

• Supports “Hyper-Threading” technology CPU

• DIM 5.0 GT/S

• Intel® P67 Chipset

• Dual-channel DDR3 memory architecture

• 4 x 240-pin DDR3 DIMM sockets support up to 16 GB

• Supports 1333 DDR3 SDRAM

• 3 x PCI Express Gen2 x16 slots

• 2 x PCI Express x1 slots

• 2 x PCI slots

• Supported by Intel® P67 Chipset

• 4 x SATA 3.0 Gb/s Host Controllers

• 2 x SATA 6.0 Gb/s Host Controllers

• 2 x eSATA 6.0 Gb/s

• Realtek ALC892 8-Ch HD audio CODEC

• Compliant with HD audio specification

• Dual Realteck 8111E Gigabit Lan

• 1 x PS/2 keyboard & PS/2 mouse combo connector

• 1 x CLR CMOS button

• 4 x USB3.0 ports(Compatible with 4 x USB2.0 ports)

• 6 x USB2.0 ports

• 2 x eSATA ports

• 2 x RJ45 LAN connectors

• 1 x Audio port with 6 audio jacks (Center/ Subwoofer Speaker Out/ Rear Speaker Out / Side Speaker Out / Line in, microphone in, line out, and optical SPDIF out)

• 1 x 24-pin ATX Power Supply connector, 8-pin 12V connector

• 2 x Serial ATA 6Gb/s connectors

• 4 x Serial ATA 3Gb/s connectors

• 1 x USB3.0 header

• 4 x USB2.0 headers support additional 8 USB ports (F_USB1 supports EZ Charger)

• 1 x Front panel audio header

• 1 x SPDIF out header

• 1 x Panel header

• 1 x ME UNLOCK header

• 1 x Reset button

• 1 x Power button

• 1 x COM header

• CPU_FAN/SYS_FAN/PWR_FAN connectors

• AMI BIOS with 32 Mb SPI Flash ROM

• Supports ECS M.I.B X Utility

• Supports ACPI&DMI, Plug and Play, STR(S3)/STR(S4)/S1,

Hardware monitor

• Audio, LAN, can be disabled in BIOS

• F7 hot key for boot up devices option

Introducing the Motherboard

Page 13

Motherboard Components

Introducing the Motherboard

Page 14

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket

LGA1155 socket for 2nd Generation Intel® Cor e Unlock processors

Family &

2. CPU_FAN CPU cooling fan connector

3. DDR3_1~4 240-pin DDR3 SDRAM slots

4. PWR_FAN Power cooling fan connector

5. ATX_POWER Standard 24-pin ATX power connector

6. BZ Buzzer

7. RST_BTN Reset button

8. PWR_BTN Power on button

9. SATA1~6 Serial ATA connectors (SATA1~2 support SATA 6Gb/s) USB3F

10.

Front panel USB 3.0 header

11. ME_UNLOCK ME unlock header-for factory use only

12. PANEL Front panel switch/LED header

13. F_USB1~4 Front panel USB headers (F_USB1 supports EZ Charger)

14. SPI_DEBUG SPI debug header-factory use only

15. SYS_FAN System cooling fan connector

16. COM Onboard serial port header

17. SPDIFO SPDIF out header

18. F_AUDIO Front panel audio header

19. PCIE16X1~3 PCI Express slot for graphics interface

20. PCI1~2 32-bit add- on card slots

21. PCIE1~2 PCI Express x1 slots

22. ATX12V 8-pin +12V power connector

This concludes Chapter 1. The next chapter explains how to install the motherboard.

Introducing the Motherboard

Page 15

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the ATX system case. Some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries an ATX form factor of 305 x 244 mm. Choose a case that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.

Installing the Motherboard

Page 16

Do not over-tighten the screws as this can stress the motherboard.

Installing the Motherboard

Page 17

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.

Warning:

1. Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

This motherboard has an LGA1155 socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

Installing the Motherboard

Page 18

CPU Installation Procedure

The following illustration shows CPU installation components.

A. Opening of the Load Plate

· Put your thumb on the tail of the load plate and press the tail down.

· Rotate the load plate to fully open position.

B. Disengaging of the Load Lever

· Hold the hook of lever and pull it to the left side to clear retention tab.

· Rotate the load lever to fully open position.

C. Removing the Cap

· Be careful not to touch the contact at any time.

D. Inserting the Package

· Grasp the package. Ensure to grasp on the edge of the substrate.

· Make sure pin 1 indicator is on your bottom-left side.

· Aim at the socket and place the package carefully into the socket by purely vertical motion.

E. Closing the Load Plate

· Rotate the load plate onto the package IHS (Intergraded Heat Spreader).

· Engage the load lever while pressing down lightly onto the load plate.

· Secure the load lever with the hook under retention tab.

F. Fasten the cooling fan supporting base onto the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.

Installing the Motherboard

Page 19

1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a CPU.

3. Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1155 socket.

Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin DDR3 2133 (OC)/DDR3 1866 (OC)/1600 (OC)/1333/1066 SDRAM. The total memory capacity is 16 GB.

You must install at least one module in any of the four slots. Total memory capacity is 16 GB.

The four DDR3 memory sockets (DDR3_1, DDR3_2, DDR3_3 and DDR3_4) are divided into two channels and each channel has two memory sockets as following:

Channel A: DDR3_1, DDR3_3

Channel B: DDR3_2, DDR3_4

Recommend memory configuration

Mode

Sockets

DDR3_1 DDR3_2 DDR3_3 DDR3_4

1 DIMM -- Populated -- --

1 DIMM -- -- -- Populated

2 DIMMs -- Populated -- Populated

3 DIMMs Populated Populated -- Populated

3 DIMMs -- Populated Populated Populated

4 DIMMs Populated Populated Populated Populated

Due to Intel CPU spec definition, the system will not boot if only one DIMM is installed in DDR3_1 or DDR3_3. Follow the table above for recommended memory configuration.

Installing the Motherboard

Page 20

1. For best performance and compatibility, we recommend that users give priority to the white DIMMs (DDR3_2/DDR3_4 when installing DIMMs.

2. We suggest users not mix memory type. It is recommended to use the same brand and type memory on this motherboard.

Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR3 SDRAM . 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.

6 Install any remaining DIMM modules.

* For reference only

Installing the Motherboard

Page 21

Expansion Slots

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

PCIE16X_1~3 Slots

PCIE1~2 Slots

PCI1~2 Slots

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

The PCI Express x16 slots are used to install external PCI Express graphics cards that are fully compliant to the PCI Express Base Specification revision 2.0. (two (x16, x16) or three (x16, x8, x8))

The PCI Express x1 slots are fully compliant to the PCI Express Base Specification revision 2.0.

This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.

Installing the Motherboard

Page 22

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the

slot you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

* For reference only

1. For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

2. The onboard PCI interface does not support 64-bit SCSI cards.

Installing the Motherboard

Page 23

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

F_AUDIO: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.

Pin Signal Name Pin Signal Name

1 PORT 1L 2 AUD_GND 3 PORT 1R 4 PRESENCE# 5 PORT 2R 6 SENSE1_RETURN

7 SENSE_SEND 8 KEY

9 PORT 2L 10 SENSE2_RETURN

SA T A1/2: Serial A T A connectors

These connectors are used to support the Serial ATA devices for the highest data transfer rates (6.0 Gb/s), simpler disk drive cabling and easier PC assembly. It doubles the transfer rate of current SATA 3.0Gb/s interface.

Pin Signal Name

1 Ground 2 TX+

3 TX- 4 Ground

5 RX- 6 RX+ 7 Ground - -

Pin Signal Name

Installing the Motherboard

Page 24

SAT A3~6: Serial A T AII connectors

These connectors are used to support the Serial ATA 3Gb/s devices, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

Pin Signal Name

1 Ground 2 TX+

3 TX- 4 Ground

5 RX- 6 RX+ 7 Ground - -

Pin Signal Name

F_USB1~4 (USB 2.0): Front Panel USB 2.0 headers

The motherboard has four USB 2.0 headers supporting eight USB 2.0 ports. Additionally, some computer cases have USB 2.0 ports at the front of the case. If you have this kind of case, use auxiliary USB 2.0 connector to connect the frontmounted ports to the motherboard.

Unlike F_USB2~4 in this mainboard, F_USB1 supports EZ Charger technology, provides about 1A current than general USB port in off mode for USB devices. It is useful and excellent, especially for the iPhone, iPad and iPod touch devices that need a large amount of current for faster recharging within less time.

Pin Signal Name Function

1 USBPWR Front Panel USB Power

2 USBPWR Front Panel USB Power

3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal

5 USB_FP_P0+ USB Port 0 Positive Signal 6 USB_FP_P1+ USB Port 1 Positive Signal

7 GND Ground 8 GND Ground 9 Key No pin

10 USB_FP_OC0 USBOC-

SPDIFO: SPDIF out header

This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.

Pin Signal Name

1 SPDIFOUT

2 +5V 3 Key

4 GND

Installing the Motherboard

Page 25

USB3F: Front Panel USB 3.0 header

This Motherboard implements one USB 3.0 header supporting 2 extra front USB 3.0 ports, which delivers 5Gb/s transfer rate.

Pin Signal Name Function

1 Vbus Front Panel USB Power

2 IntA_P1_SSRX- USB3 ICC Port1 SuperSpeed Rx-

3 IntA_P2_SSRX+ USB3 ICC Port1 SuperSpeed Rx+

4 GND GND

5 IntA_P1_SSTX- USB3 ICC Port1 SuperSpeed Tx- 6 IntA_P1_SSTX+ USB3 ICC Port1 SuperSpeed Tx+

7 GND GND 8 IntA_P1_D- USB3 ICC Port1 D- 9 IntA_P1_D+ USB3 ICC Port1 D+

10 ID USBOC- Over Current Protection

11 IntA_P2_D+ USB3 ICC Port2 D+

12 IntA_P2_D- USB3 ICC Port2 D- 13 GND GND

14 IntA_P2_SSTX+ USB3 ICC Port2 SuperSpeed Tx+

15 IntA_P2_SSTX- USB3 ICC Port2 SuperSpeed Tx- 16 GND GND

17 IntA_P2_SSRX+ USB3 ICC Port2 SuperSpeed Rx+

18 IntA_P2_SSRX- USB3 ICC Port2 SuperSpeed Rx-

19 Vbus Front Panel USB Power

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.

ME_UNLOCK: ME Unlock Header

Pin 1-2 Function

Short Unlock

Open Lock

Installing the Motherboard

Page 26

Installing SAT A Hard Drives

This section describes how to install SATA devices such as a hard disk drive and a CDROM drive.

About SA TA Connectors

Your motherboard features four SATA 3.0 Gb/s connectors and two SATA 6.0Gb/s connectors supporting a total of six drives SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the SATA hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

Installing Serial A T A Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

SATA cable (optional) SATA power cable (optional)

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the

other end to the power supply.

* For reference only

This motherboard supports the “Hot-Plug” function.

Installing the Motherboard

Page 27

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

PS/2 Keyboard/Mouse Combo Port

CLR_CMOS Button

eSATA 6 Gb/s ports Use these ports to connect to external SATA boxes or

LAN Ports

USB 2.0 Ports USB 3.0 Ports Use the USB 3.0 ports to connect USB 3.0 devices.

Optical SPDIF Output

Audio Ports

Connect the PS/2 Keyboard or PS/2 Mouse to the PS/2 combo port.

Use the CLR_CMOS button to clear CMOS.

Before clearing CMOS, make sure to turn off the power of the system.

Serial ATA port multipliers.

Connect an RJ-45 jack to the LAN port to connect your computer to the Network.

Use the USB 2.0 ports to connect USB 2.0 devices.

This jack connects to external optical digital audio output devices.

Use the audio jacks to connect audio devices. The C port is for stereo line-in signal, while the E port is for microphone in signal. This motherboard supports audio devices that correspond to the A, B, and D port respectively. In addition, both of the 2 ports, B, and D provide users with both right & left channels individually. Users please refer to the following note for specific port function definition.

A: C enter & Woofer D: Front Out B: Bac k Surround E: Mic _in R ear C: Line-in -

The above port definition can be changed to audio input or audio output by changing the driver utility setting.

Installing the Motherboard

Page 28

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the system cooling fan connector to SYS_FAN. 3 Connect the power cooling fan connector to PWR_FAN. 4 Connect the case switches and indicator LEDs to the PANEL. 5 Connect the standard power supply connector to ATX_POWER. 6 Connect the auxiliary case power supply connector to ATX12V.

1. Connecting 24-pin power cable

The ATX 24-pin connector allows you to connect to ATX v2.x power supply.

24-pin power cable

With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX_POWER match perfectly.

Installing the Motherboard

Page 29

2. Connecting 8 power cable

Users please note that the 8-pin and 4-pin power cables can both be connected to the ATX12V connector.

When installing 8-pin power cable, the latches of power cable and the ATX12V connector

match perfectly.

8-pin power cable

CPU_FAN: CPU cooling F AN Power Connector

Pin Signal Name Function

1 GND System Ground 2 +12V Power +12V 3 Sense Sensor 4 PWM PWM

Users please note that the fan connector supports the CPU cooling fan of

1.1A ~ 2.2A (26.4W max) at +12V.

SYS_FAN: F AN Power Connectors

Pin Signal Name Function

1 GND System Ground 2 +12V Power +12V 3 Sense Sensor 4 PWM PWM

A TX_ POWER: A TX 24-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V 3 Ground 15 Ground

4 +5V 16 PS_ON

5 Ground 17 Ground

6 +5V 18 Ground 7 Ground 19 Ground 8 PWRGD 20 -5V

9 +5VSB 21 +5V

10 +12V 22 +5V 11 +12V 23 +5V

12 +3.3V 24 Ground

Installing the Motherboard

Page 30

PWR_FAN: F AN Power Connector

Pin Signal Name Function

1 GND System Ground

2 +12V Power +12V 3 Sense Sensor

A TX12V: A TX 12V Power Connector

Pin Signal Name

1 Ground

2 Ground

3 Ground

4 Ground

Pin Signal Name

5 +12V

6 +12V

7 +12V

8 +12V

Installing the Motherboard

Page 31

Panel Header

The panel header (PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:

Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)

3 HD_LED_N Hard disk LED(- )

5 RST_SW_N Reset Switch(-)

7 RST_SW_P Reset Switch(+)

9 RSVD Reserved

* MSG LED (dual color or single color)

Users please note that the above picture is for reference only, you should determine the header pin definition by the actual key pin location.

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

4 FP PWR/SLP *MSG LED(-)

6 PWR_SW_P Power Switch(+)

8 PWR_SW_N Power Switch(-)

10 Key No pin

This concludes Chapter 2. The next chapter covers the BIOS.

Installing the Motherboard

Page 32

Memo

Installing the Motherboard

Page 33

Chapter 3

Using BIOS

About the Setup Utility

The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Press DEL to enter SETUP

Using BIOS

Page 34

Press the delete key to access BIOS Setup Utility.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

BIOS Information

System Data [ Mon 09/27/2010]

System Time [02:06:56]

Set the Date. Use Tab to

switch between Date elements

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.

Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.



) lead to submenus that enable you to change



Using BIOS

Page 35

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle



.



The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

ESC Exits the current menu



+/- Modifies the selected field’s values

Enter Select

F1 General Help F2 Previous Value F3 Optimized Defaults

F4 Save & Exit

For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.

Scrolls through the items on a menu

Main Menu

When you enter the BIOS Setup program, the main menu appears, giving you an overview of the basic system information. Select an item and press <Enter> to display the submenu.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

BIOS Information

System Data [ Mon 09/27/2010]

System Time [02:06:56]

Set the Date. Use Tab to switch between Date elements.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Using BIOS

Page 36

Date & Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.

Advaned Menu

The Advanced menu items allow you to change the settings for the CPU and other system.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Legacy OpROM Support

Launch PXE OpROM [Disabled]

Launch Storage OpROM [Enabled]

LAN Configuration







ECS eJIFFY Function







PC Health Status







Power Management Setup







ACPI Settings







CPU Configuration







SATA Configuration







USB Configuration







Super IO Configuration







Main Advanced Chipset M.I.B X Boot Security Save & Exit

Legacy OpROM Support Launch PXE OpROM [Disabled]

Launch Storage OpROM [Enabled]

LAN Configuration







ECS eJIFFY Function







PC Health Status







Power Management Setup







ACPI Settings







CPU Configuration







SATA Configuration







USB Configuration







Super IO Configuration







Launch PXE OpROM Disabled Enabled

Launch Storage OpROM Disabled Enabled

Enable/Disable Onboard LAN Option ROM

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Enable/Disable Onboard LAN Option ROM

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Launch PXE OpROM

The item enables or disables launch PXE Option ROM.

Launch Storage OpROM

The item enables or disables launch Storage Option ROM.

LAN Configuration

The item in the menu shows the LAN-related information that the BIOS automatically detects.

Using BIOS

Page 37

Main Advanced Chipset M.I.B X Boot Security Save & Exit

LAN Configuration

Onboard LAN 1 Controller [Enabled]

Onboard LAN 2 Controller [Enabled]

Main Advanced Chipset M.I.B X Boot Security Save & Exit

LAN Configuration

Onboard LAN 1 Controller [Enabled]

Onboard LAN 2 Controller [Enabled]

Onboard LAN 1 Controller Disabled Enabled

Enable or Disable Onboard LAN 1 Controller

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Enable or Disable Onboard LAN 1 Controller

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Main Advanced Chipset M.I.B X Boot Security Save & Exit

LAN Configuration

Onboard LAN 1 Controller [Enabled]

Onboard LAN 2 Controller [Enabled]

Onboard LAN 2 Controller Disabled Enabled

Onboard LAN1/2 Controller (Enabled)

Use this item to enable or disable the Onboard LAN.

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Enable or Disable Onboard LAN 1 Controller

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Page 38

ECS eJIFFY Function

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset M.I.B X Boot Security Save & Exit

ECS eJIFFY Function

ECS eJIFFY Function [Disabled]

Main Advanced Chipset M.I.B X Boot Security Save & Exit

ECS eJIFFY Function

ECS eJIFFY Function [Disabled]

ECS eJIFFY Function

Disabled

Enabled

Make sure that the eJIFFY has been installed to hard disk.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Make sure that the eJIFFY has been installed to hard disk.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

ECS eJIFFY Function (Disabled)

This item allows you to enable or disable ECS eJIFFY Function.

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Page 39

PC Health Status

On motherboards support hardware monitoring, this item lets you monitor the paeameters for critical voltages, temperatures and fan speeds.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Smart Fan Function



System Temperature : 29°C CPU Fan Speed : 704 RPM System Fan Speed : 3139 RPM CPU Vcor e : 0.960V IMC Voltage : 1.044V VDIMM : 1.512V PCH Voltage : 1.092V

-=- PECI Mode -=-

Offset to TCC Activation Temp : -38



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults

-=- PECI Mode -=-

F4:Save & Exit

ESC:Exit

Offset to TCC Activation Temp : -27

Smart Fan Function

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset M.I.B X Boot Security Save & Exit

SMART Fan Control [Enabled]

SMART Fan Mode [Normal]

SMART Fan start PWM value 56 SMART Fan start PWM TEMP(-) 30 Delta T +3 SMART Fan Slope PWM value 10 PWM value/unite CPU Fan Full Speed Offset (-) 10

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

SMART FAN Control (Enabled)

This item allows you to enable/disable the control of the system fan speed by changing the fan voltage.

SMART Fan Mode (Normal)

This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.

Using BIOS

Page 40

SMART Fan start PWM value (56)

This item is used to set the start PWM value of the smart fan.

SMART Fan start TEMP(-) (30)

This item is used to set the start temperature of the smart fan.

DeltaT (+3)

This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.

SMART Fan Slope PWM value (10 PWM value/unite)

This item is used to set the Slope Select PWM of the smart fan.

CPU Fan Full Speed Offset(-) (10)

This item is used to set the CPU fan full speed offset value.

Press <Esc> to return to the PC Health Status page.

System Component Characteristics

These items display the monitoring of the overall inboard hardware health events, such as System & CPU temperature, CPU & DIMM voltage, CPU & system fan speed,... etc.

• CPU Vcore

• IMC Voltage

• VDIMM

• PCH Voltage

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Page 41

Power Management Setup

This page sets up some parameters for system power management operation.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Power Management Setup

Resume by Ring [Disabled]

Resume By PCI/PCI-E/Lan PME [Disabled] Resume by USB (S3) [Disabled] Resume by PS2 KB (S3) [Disabled] Resume by PS2 MS (S3) [Disabled] EUP Function [Disabled]

About Resume by Ring

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Resume by Ring (Disabled)

An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state.

Resume By PCI/PCI-E/Lan PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card.

Resume By USB (S3) (Disabled)

This item allows you to enable/disable the USB device wakeup function from S3 mode.

Resume By PS2 KB (S3) (Disabled)

This item enables or disables you to allow keyboard activity to awaken the system from power saving mode.

Resume By PS2 MS (S3) (Disabled)

This item enables or disables you to allow mouse activity to awaken the system from power saving mode.

EUP Support (Disabled)

This item allows user to enable or disable EUP support.

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Page 42

ACPI Configuration

The item in the menu shows the highest ACPI sleep state when the system enters suspend.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

ACPI Configuration

ACPI Sleep State [S3 (Suspend to RAM)]

Main Advanced Chipset M.I.B X Boot Security Save & Exit

ACPI Configuration

ACPI Sleep State [S3 (Suspend to RAM)]

ACPI Sleep State

Suspend Disabled

S1 (CPU Stop Clock) S3 (Suspend to RAM)

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults F4:Save & Exit ESC:Exit

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults F4:Save & Exit ESC:Exit

ACPI Sleep State (S3(Suspend to RAM))

This item allows user to enter the APCI S3 (Suspend toRAM) Sleep State(default).

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Page 43

CPU Configuration

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset M.I.B X Boot Security Save & Exit

CPU Configuration

Intel (R) Core (TM) i7-2600K CPU @ 3.40GHz EMT64 Supported Processor Speed 1600 MHz Processor Stepping 206a2 Microcode Revision 22 Processor Cores 4 Intel HT Technology Supported

Hyper-threading [Enabled]

Limit CPUID Maximum [Disabled] Execute Disable Bit [Enabled] Intel Virtualization Technology [Disabled] Power Technology [Custom] CPU C3 Report [Disabled] CPU C6 Report [Enabled] Package C State limit [No Limit]

1-Core Ratio Limit 0 2-Core Ratio Limit 0 3-Core Ratio Limit 0

4-Core Ratio Limit 0

Main Advanced Chipset M.I.B X Boot Security Save & Exit

CPU Configuration

Intel (R) Core (TM) i7-2600K CPU @ 3.40GHz EMT64 Supported Processor Speed 1600 MHz Processor Stepping 206a2 Microcode Revision 22 Processor Cores 4 Intel HT Technology Supported

Hyper-threading [Enabled] Limit CPUID Maximum [Disabled] Execute Disable Bit [Enabled] Intel Virtualization Technology [Disabled]

Power Technology [Custom]

CPU C3 Report [Disabled] CPU C6 Report [Enabled] Package C State limit [No Limit] 1-Core Ratio Limit 0 2-Core Ratio Limit 0

3-Core Ratio Limit 0 4-Core Ratio Limit 0

Power Technology Disabled Energy Efficient Custom

Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS(OS not optimized for Hyper-ThreadingTechnology). When Disabled only one thread per enabled core is enabled.

:Select Screen



:Select Item



Enter : Select

+/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and Disabled for other OS(OS not optimized for

Hyper-ThreadingTechnology). When Disabled only one thread per enabled core is enabled.

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Using BIOS

Page 44

Inter(R) Core (TM) i7-2600K CPU @ 3.40 GHz

This is display-only field and diaplays the information of the CPU installed in your computer.

EMT64 (Supported)

This item shows the computer supports EMT64.

Processor Speed (1600MHz)

This item shows the processor speed.

Processor Stepping (206a2)

This item shows the information of processor stepping.

Microcode Revision (22)

This item shows the Microcode revision.

Processor Cores (4)

This item shows the information of the processor cores.

Intel HT Technology (Supported)

This item shows your computer supports Intel HT technology.

Hyper-threading (Enabled)

This item enables or disables Hyper-threading.

Limit CPUID Maximum (Disabled)

Use this item to enable or disable the maximum CPUID value limit. When supports Prescott and LGA775 CPUs, enables this to prevent the system from “rebooting” when trying to install Windows NT 4.0.

Excute Disable Bit (Enabled)

This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.

Intel Virtualization Technology (Disabled)

When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.

CPU C3 Report (Disabled)

This item enables or disables the CPU C3 Report.

CPU C6 Report (Enabled)

This item enables or disables the CPU C6 Report.

Package C State limit (No Limit)

Use this item to set the Package C State limit.

1/2/3/4-Core Ratio Limit (0)

This item shows the Core Ratio Limit value.

Press <Esc> to return to the Advanced Menu page.

Using BIOS

Page 45

SA T A Configuration

Use this item to show the mode of serial SATA configuration options.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

SATA Configuration

SATA Mode [IDE Mode]

Serial-ATA Controller 0 [Compatible] Serial-ATA Controller 1 [Enhanced] eSATA 6Gb/s Controller Mode [AHCI Mode]

SATA Port0 Not Present

SATA Port1 Not Present

SATA Port2 ST3320620AS (320.0

SATA Port3 Not Present

SATA Port4 SONY DVD RW ATAPI

SATA Port5 Not Present

(1) IDE Mode. (2) AHCI Mode.

(3) RAID Mode.

:Select Screen



:Select Item



Enter : Select

+/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

Main Advanced Chipset M.I.B X Boot Security Save & Exit

SATA Configuration

SATA Mode [IDE Mode]

Serial-ATA Controller 0 [Compatible] Serial-ATA Controller 1 [Enhanced] eSATA 6Gb/s Controller Mode [AHCI Mode]

SATA Port0 Not Present

SATA Port1 Not Present

SATA Port2 ST3320620AS (320.0

SATA Port3 Not Present

SATA Port4 SONY DVD RW ATAPI

SATA Port5 Not Present

(1) IDE Mode. (2) AHCI Mode.

(3) RAID Mode.

SATA Mode

Disabled

IDE Mode

AHCI Mode

RAID Mode

:Select Screen



:Select Item



Enter : Select

+/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

SATA Mode (IDE Mode)

Use this item to select SATA mode.

Serial-ATA Controller 0/1 (Compatible/Enhanced)

Use this item to show the Serial-ATA cotroller options: Disabled, Compatible, Enhanced.

Using BIOS

Page 46

eSATA 6 Gb/s Controller Mode (AHIC Mode)

Use this item to select eSATA 6 Gb/s controller mode.

SATA Port 0~5

This motherboard supports six SATA channel and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.

Press <Esc> to return to the Advanced Menu page.

USB Configuration

Use this item to show the information of USB configuration.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

USB Configuration

All USB Devices [Enabled]

USB 3.0 Controller [Enabled]

Legacy USB Support [Enabled]

Main Advanced Chipset M.I.B X Boot Security Save & Exit

USB Configuration

All USB Devices [Enabled]

USB 3.0 Controller [Enabled]

Legacy USB Support [Enabled]

All USB Devices Disabled Enabled

Enabled/Disabled All USB Devices

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Enabled/Disabled All USB Devices

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

All USB Devices (Enabled)

Use this item to enable or disable all USB devices.

Using BIOS

Page 47

USB 3.0 Controller (Enabled)

Use this item to enable or disable USB 3.0 controller. We recommand users keep the default value. Disabling it might cause the USB devices not to work properly.

Legacy USB Support (Enabled)

Use this item to enable or disable support for legacy USB devices.

Press <Esc> to return to the Advanced Menu page.

Super IO Configuration

Use this item to show the information of Super IO configuration.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Super IO Configuration

Super IO Chip IT8728

Serial Port 0 Configutation







Temp. to 80-Port [Disabled]

Set Parameters of Serial Port 0 (COMA)

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Super IO Chip (IT8728)

This item shows the information of the super IO chip.

Serial Port 0 Configuration

This item shows the information of the super IO chip.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Serial Port 0 Configuration

Serial Port [Enabled]

Device Settings IO=3F 8h; IRQ=4;

Change Settings [Auto]

Serial Port Disabled Enabled

Using BIOS

Enable or Disable Serial Port (COM)

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Page 48

Serial Port (Enabled)

This item allows you to enable or disable serial port.

Device Settings (IO=3F 8h; IRQ=4)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

Press <Esc> to return to the Super IO Configuration page.

Temp. to 80-Port (Disabled)

This item enables or disables

Temperature (°C) to 80-Port.

Using BIOS

Page 49

Chipset Menu

The chipset menu items allow you to change the settings for the North chipset, South chipset and other system.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

North Bridge



South Bridge



ME Subsystem



North Bridge

Scroll to this item and press <Enter> and view the following screen.

North Bridge Parameters

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Main Advanced Chipset M.I.B X Boot Security Save & Exit

North Bridge

Initate Graphic Adapter [PCI Express]

Select which graphics controller to use as the primary boot device.

:Select Screen

Initate Graphic Adapter

PCI PCI Express



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Initate Graphic Adapter (PCI Express)

This item allows you to select graphics controller to use as the primary boot device.

Press <Esc> to return to the chipset menu page.

Using BIOS

Page 50

South Bridge

Scroll to this item and press <Enter> to view the following screen.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

South Bridge

Restore AC Power Loss [Power Off]

Audio Configuration Azaia HD Audio [Enabled]

Main Advanced Chipset M.I.B X Boot Security Save & Exit

South Bridge

Restore AC Power Loss [Power Off]

Audio Configuration Azaia HD Audio [Enabled]

Restore AC Power Loss Power Off Power On Last State

Specify what state to go to when power is re-applied after a power failure (G3 state).

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Specify what state to go to when power is re-applied after a power failure (G3 state).

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Main Advanced Chipset M.I.B X Boot Security Save & Exit

South Bridge

Restore AC Power Loss [Power Off]

Audio Configuration

Azaia HD Audio [Enabled]

Azalia HD Audio

Disabled Enabled

Using BIOS

Enabled/Disabled Azalia HD Audio

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults F4:Save & Exit ESC:Exit

Page 51

Restore AC Power Loss (Power Off)

This item specifies what state to go to when power is re-applied after a power failure (G3 state).

Audio Configuration

This item shows the information of the audio configuration.

Azaia HD Audio (Enabled)

This item enables or disables Azaia HD audio.

Press <Esc> to return to the chipset menu page.

ME Subsystem

Scroll to this item and press <Enter> to view the following screen.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Intel ME Subsytem Configuration

ME Version 7.0.0.1105

ME Subsystem [Enabled]

ME Subsystem Help

:Select Screen

ME Subsystem Disabled Enabled

Azalia HD Audio

Disabled

Enabled



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

ME Version (7.0.0.1105)

This item shows the ME version.

ME Subsystem (Enabled)

This item allows you to enable or disable ME subsystem.

Using BIOS

Page 52

M.I.B X (MB Intelligent BIOS X) Menu

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

M.I.B X (MB Intelligent BIOS X)

Integrated Clock Chip Configuration



Performance Tunning



Auto Detect DIMM/PCI Clk [Enabled] Spread Spectrum [Enabled]

XMP Support By [SPD] PCH Voltage [1.08V] PLL Voltage [1.83V] DIMM Voltage [Disabled] CPU Voltage [Disabled] IMC Voltage [Disabled]

Intel(R) Core(TM) i5-2400 CPU @ 3.10GHz Processor Speed 3100 MHz Total Memory 1024 MB (DDR3 1333) VDIMM 1.512V CPU Current Voltage 1.164V IM C 1.044V

Integrated Clock Chip Parameters

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Integrated Clock Chip Configuration

Scroll to this item to view the following screen:

Main Advanced Chipset M.I.B X Boot Security Save & Exit

CPU Ratio 31 IA Core Current [Normal] Power Limit 1 Value (Watt) 95 Power Limit 2 Switch [Enabled] Power Limit 2 Value 118 Long duration maintained (Tau) 1 Enhanced Intel SpeedStep Technology [Enabled]

Turbo Mode [Disabled]

Turbo Mode

:Select Screen



:Select Item



Enter : Select

Turbo Mode

Disabled

Enabled

+/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

CPU Ratio (31)

This item allows users to control non turbo CPU ratio.

IA Core Current (Normal)

Use this item to control Primary Plant Current Limit. This is for Turbo mode.

Using BIOS

Page 53

Power Limit 1 Value(Watt) (95)

Use this item to control the limit of the TDP. This is for Turbo mode.

Power Limit 2 Switch (Enabled)

Use this item to control the Power Limit 2. This is for Turbo mode.

Power Limit 2 Value (1)

Use this item to control Power Limit 2. PL2 provides an upper limit of the TDP excursions. This is for Turbo mode.

Long duration maintainded(Tau) (1)

Use this item to control the time window over PL1 value should be maintained. This is for Turbo mode.

Enhanced Intel SpeedStep Technology (Enabled)

This item allows users to enable or disable the EIST(Enhanced Intel SpeedStep Technology).

Turbo Mode (Disabled)

This item allows you to control the Intel Turbo Boost Technology.

Press <Esc> to return to the M.I.B X menu page.

 Performance Tunning

Scroll to this item to view the following screen:

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Memory Multiplier Configuration

Memory Multiplier [13.33]

Memory Timing Configuration

CAS# Latency (tcl) 9 Row Precharge Time (tRP) 9 RAS# to CAS# Delay (tRCD) 9 RAS# Active Time (tRAS) 24

Memory Multiplier

:Select Screen



:Select Item



Enter : Select

Memory Multiplier

Auto

10.67

13.33 16

18.67

21.33

+/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

Memory Multiplier (13.33)

Use this item to set the system memory multiplier.

Memory Timing Configuration

This item shows the information of Memory Timing Configuration.

Using BIOS

Page 54

CAS#Latency(tcl) (9)

This item determines the operation of DDR SDRAM memory CAS(colulmn address strobe). It is recommanded that you leave this item at the default value. The 2T setting requires faster memory that specifically supports this mode.

Row Precharge Time(tRP) (9)

This item specifies Row precharge to Active or Auto-Refresh of the same bank.

RAS# to CAS# Delay(tRD) (9)

This item specifies the RAS# to CAS# delay to Rd/Wr command to the same bank.

RAS# Active Time(tRAS) (24)

This item specifies the RAS# active time.

Press <Esc> to return to the M.I.B X menu page.

Auto Detect DIMM/PCI Clk (Enabled)

When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.

Spread Spectrum (Enabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

XPM Support By (SPD)

This item allows users to set the XPM Support.

PCH Voltage (1.08V)

This item allows users to adjust the current PCH voltage.

PLL Voltage (1.83V)

This item allows users to adjust the current PLL voltage.

DIMM Voltage (Disabled)

This item allows users to adjust the DIMM voltage.

CPU Voltage (Disabled)

This item allows users to adjust the CPU voltage.

IMC Voltage (Disabled)

This item allows users to adjust the IMC voltage.

Intel(R) Core(TM) CPU i5-2400 @ 3.10 GHz

This is display-only field and displays the information of the CPU installed in your computer.

Processor Speed (3100MHz)

This item shows the CPU speed.

Total Memory (1024MB(DDR3 1333))

This item shows the total momery of DDR3.

VDIMM (1.512V)

This item displays the current VDIMM voltage.

Using BIOS

Page 55

CPU Current Voltage (1.164V)

This item diplays the CPU current voltage.

IMC Voltage (1.044V)

This item displays the current IMC voltage.

Using BIOS

Page 56

Boot Menu

This page enables you to set the keyboard NumLock state.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Boot Configuration

Bootup NumLock State [On]

Quiet BOOT [Enabled]

Boot Option Priorities Boot Option #1 [SATA: SONY DVD ...] Boot Option #2 [SATA: ST3320620AS ...]

CD/DVD ROM Drive BBS Priorities Hard Drive BBS Priorities

Boot Configuration

This item shows the information of the Boot Configuration.

Bootup NumLock State (On)

This item enables you to select NumLock state.

Quiet BOOT (Enabled)

This item enables or disables quiet boot.

Boot Option Priorities

This item enables you to set boot option priorities.

Boot Option #1/#2 (SATA: SONY DVD .../SATA: ST3320620AS ...)

Use these items to determine the device order the computer uses to look for an operating system to load at start-up time.

CD/DVD ROM Drive BBS Priorities

This item enables you to specify the sequence of loading the operating system from the installing CD/DVD ROM drives.

Hard Drive BBS Priorities

This item enables you to specify the sequence of loading the operating system from the installing hard drives.

Select the keyboard NumLock state

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Using BIOS

Page 57

Security Menu

This page enables you to set setup administrator and password.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights. The password must be3 to20 characters long.

Administrator Password

Scroll to this item and press <Enter> to view the following screen.

Set Setup Administrator Password

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Main Advanced Chipset M.I.B X Boot Security Save & Exit

If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup.

Administrator Password

Create New Password

Use this item to set setup administrator password.

Using BIOS

Set Setup Administrator Password

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value F3:Optimized Defaults F4:Save & Exit

ESC:Exit

Page 58

Save & Exit Menu

This page enables you to exit system setup after saving or without saving the changes.

Main Advanced Chipset M.I.B X Boot Security Save & Exit

Save Changes and Exit

Discard Changes and Exit Save Changes and Reset Discard Changes and Reset

Save Options Save Changes Discard Changes

Restore Defaults Save as User Defaults Restore User Defaults

Boot Override SATA: SONY DVD RW DRU-190S SATA : ST3320620AS

Laucnch EFI Shell from filesystem device

Exit system setup after saving the changes.

Sa ve & Exi t Se tup

Save configuration and exit?

Yes N o

:Select Screen



:Select Item



Enter : Select +/- : Value

F1:General Help

F2:Previous Value

F3:Optimized Defaults

F4:Save & Exit

ESC:Exit

Save Changes and Exit

This item enables you to exit system setup after saving the changes.

Discard Changes and Exit

This item enables you to exit system setup without saving any changes.

Save Changes and Reset

This item enables you to reset the system setup after saving the changes.

Discard Changes and Reset

This item enables you to reset system setup without saving any changes.

Save Options

This item enables you to save the options that you have made.

Save Changes

This item enables you to save the changes that you have made.

Discard Changes

This item enables you to discard any changes that you have made.

Restore Defaults

This item enables you to restore the system defaults.

Save as User Defaults

This item enables you to save the changes that you have made as user defaults.

Restore User Defaults

This item enables you to restore user defaults to all the setup options.

Using BIOS

Page 59

Boot Override

Use this item to select the boot device.

SA T A: SONY DVD RW DRU-190S

This item enables you to boot from this device.

SATA: ST3306260AS

This item enables you to boot from this device.

Launch EFI Shell from filesystem device

This item enables you to launch EFI shell from filesystem device.

Using BIOS

Page 60

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to

allow BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Ad-

vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)

3 Prepare a bootable device or create a bootable system disk. (Refer to

Windows online help for information on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s

Web site. Copy these files to the bootable device.

5 Turn off your computer and insert the bootable device in your com-

puter. (You might need to run the Setup Utility and change the the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)

6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file

name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE

040706.ROM

7 When the installation is complete, remove the bootable device from the

computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

Using BIOS

Page 61

Chapter 4

Using the Motherboard Software

About the Software DVD-ROM/CD-ROM

The support software DVD-ROM/CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software. Before installing any software, always inspect the folder for files named README.TXT or something similar. These files may contain important information that is not included in this manual.

1. Never try to install all software from folder that is not specified for use with your motherboard.

2. The notice of Intel HD Audio Installation (optional): The Intel High Definition audio functionality unexpectedly quits working in Windows Server 2003 Service Pack 1 or Windows XP Professional x64 Edition. Users need to download and install the update packages from the Microsoft Download Center “before” installing HD audio driver bundled in the driver disk. Please log on to http://support.microsoft.com/ default.aspx?scid=kb;en-us;901105#appliesto for more information.

Auto-installing under Windows XP/V ista/7

The Auto-install DVD-ROM/CD-ROM makes it easy for you to install the drivers and software for your motherboard.

If the Auto-install DVD-ROM/CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.

The support software DVD-ROM/CD-ROM disc loads automatically under Windows XP/Vista/7. When you insert the DVD-ROM/CD-ROM disc in the DVD-ROM/CDROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.

* For reference only

If the opening screen does not appear; double-click the file “setup.exe” in the root directory.

Using the Motherboard Software

Page 62

Drivers

Setup

Utilities

Browse CD

Click the Setup button to run the software installation program. Select from the menu which software you want to install.

Click the Utilities button to display the application software and other software utilities that are available on the disk. Select the sofware you want to install then follow installation procedure.

The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support disk.

Before installing the software from Windows Explorer, look for a file named README.TXT or something similar. This file may contain important information to help you install the software correctly.

Some software is installed in separate folders for different operating systems.

In installing the software, execute a file named SETUP.EXE by doubleclicking the file and then following the instructions on the screen.

Exit

Utilities

Lists the software utilities that are available on the disk.

Information

Displays the path for all software and drivers available on the disk.

The EXIT button closes the Auto Setup window.

Running Setup

Follow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

Page 63

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default optionsare recom-

mended.

4. Click Next run the Installation Wizard. An item installation screen appears:

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Using the Motherboard Software

Page 64

Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select “Allow” to install the next driver.

Continue this process to complete the drivers installation.

Manual Installation

Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software.

Using the Motherboard Software

Page 65

Chapter 5

ATI CrossFireXTM Technology Support

This motherboard supports the ATI CrossFireX install multi-graphics processing units (GPU) graphics cards. Follow the installation procedures in this section.

If you want to enable the ATI CrossFireX disable(Default: Enable).

Technology that allows you to

Technology, please set Hydra Core to

Requirements

1 Two or three identical CrossFireXTM ready graphic cards are needed for the

setup of 2-way / 3-way CrossFireXTM configuration. 2 You would need one or two CrossfireXTM bridge cable. 3 Make sure that your graphics card driver supports the ATI CrossFireX

technology. Download the latest driver from the ATI website

(www.ati.com). 4 Make sure that your power supply unit (PSU) can provide at least the

minimum power required by your system.

Installing CrossFireXTM graphics cards

1. Insert the CrossFireX card is properly seated on the slot.

A. For 2-way configuration, install two graphic cards on PCIEX16_1 & PCIEX16_2

and connect them with the CrossFireTM Bridge.

graphics cards into the PCIEX16 slots. Make sure that the

* For reference only

ATI CrossFireTM Technology Support

Page 66

B. For 3-way configuration, two CrossFireTM Bridges are needed to connect the

three graphic cards.

3. Connect the cable from your monitors to the CrossFireXTM ready graphics card installed on the PCIEX16_1 slot.

Monitor Cable

* For reference only

4. Connect an auxiliary power source from the power supply to the graphics cards.

ATI CrossFireTM Technology Support

Page 67

The CatalystTM Control Center Dialog Box

To enable CrossFireXTM:

• Install ATI graphic card driver.

• Enter the Catalyst

• check the “Enable CrossFireX

• Click OK to apply.

Control Center Dialog Box.

” item.

If you want to start CrossFireXTM, you have to disable the Hydra Logix Control Panel first.

ATI CrossFireTM Technology Support

Page 68

Memo

ATI CrossFireTM Technology Support

Page 69

Chapter 6

Hydra Core Technology Support

This motherboard supports the Hydra Core Technology that allows you to install multi-graphics processing units (GPU) graphics cards, which support Hydra Core AMode, N-Mode, X-Mode. Follow the installation procedures in this section.

The default setting of Hydra Core ATI CrossFireX

Technology, please change it to Disabled.

Technology is Enabled, if you want to enable the

Requirements

1 Two or three identical or non-identical graphic cards are needed the setup

of 2-Way / 3-Way configuration. . 2 Download the latest driver from the Lucid website (www.lucidlogix.com). 3 Make sure that your power supply unit (PSU) can provide at least the

minimum power required by your system.

Installing graphics cards

1. Insert graphics cards into the PCIEX16 slots. Make sure that the card is properly seated on the slot.

For 2-Way configuration, install two graphic cards on PCIEX16_1 & PCIEX16_2. (x16, x16)

A. A-Mode Performance(Dual identical ATI graphic cards)

Hydra Core Technology Support

Page 70

B. N-Mode Performance(dual Nvidia identical graphic cards)

C. X-Mode Performance(mixture Nvidia and ATI graphic cards)

For 3-Way configuration, install three graphic cards on PCIEX16_1, PCIEX16_2

& PCIEX16_3. (x16, x8, x8)

Hydra Core Technology Support

Page 71

3. Connect the cable from your monitors to the graphic card installed on the PCIEX16_1 slot.

Monitor Cable

2-way

Monitor Cable

3-way

4. Connect an auxiliary power source from the power supply to the graphics cards.

Hydra Core Technology Support

Page 72

The HYDRALOGIX Control Panel

To enable HydraLogix:

• Install HydraLogix driver.

• Install graphic card driver.

• Enter the HYDRALOGIX Control Panel.

• check the “Enable HydraLogix” item.

• Click OK to apply.

Hydra Core Technology Support

Page 73

Chapter 7

Setting Up eJIFFY

Introduction

eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up.

Note: eJIFFY is ECS optional feature utility corresponding to the DVD activation and BIOS setup. Please check the hard copy user’s guide or product color-box to see

if the model has embodded eJIFFY feature. (eJIFFY icon on color-box )

Version: 6.0

Setting Up eJIFFY

Page 74

Installation and BIOS Setup

DVD Activation

Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation.

1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY

feature item to install.

2. Follow the onscreen instructions to finish eJIFFY setup.

Setting Up eJIFFY

Page 75

3. After setting up eJIFFY under Windows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after

rebooting.

Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing. Please refer to the usage FAQ for

more tips.

Setting Up eJIFFY

Page 76

4. Restart your computer after eJIFFY installation. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up.

5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func- tion. Press F4 to save the configuration and exit. Restart your computer.

1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID

Note:

configuration and the onboard 34-pin floppy drives.

2. Please refer to ECS website for new eJIFFY application updates.

Setting Up eJIFFY

Page 77

Entering eJIFFY

The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup.

Click to enter the normal OS you have installed

such as Windows.

Click to enter eJIFFY OS.

Click to set the BIOS.

If you click eJIFFY, the following screen will appear. And If you make no choice it will enter the normal OS automatically after ten seconds.

Setting Up eJIFFY

Page 78

Feature Icons

The following illustration shows the main feature icons that eJIFFY provides on the menu.

eWeb: Firefox for web browsing/webmail and watching flash video.

ePix: Photo viewing.

ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ, AIM, etc.)

Shows ePal on-line connection status.

Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer..

Shows the network connection status.

Click once to connect the storage disk to your computer. Click for the second time to remove your storage disk safely. (please refer to the FAQ for more usage information.)

Language Control Panel

Switch Keyboard Languages

Allows you to adjust the sound volume level from mute to the max

Setting Up eJIFFY

Page 79

Usage F AQ

Language Control Panel: Besides setting English as the default interface, eJIFFY offers multi-language displays and keyboard settings for languageswitch. Open the language control panel to select a preferable language setting.

Keyboard Language Setup

Step1. Click

Step 2: Click “Keyboard Language” icon to open the keyboard selection

list, which offers several regional keyboard settings besides default English keyboard. Step 3: Click the selected keyboard language (e.g. English(US)) and press “OK”.

to open the language control panel.

Setting Up eJIFFY

Page 80

Click to enable all possible language inputs you want to apply, and click

“Apply”:

Move your mouse pointer on the text box and press Ctrl+Space. The language bar will then appear as follows.

Select your desired language

Click the language bar here.

Setting Up eJIFFY

Page 81

How to change display language?

Open the Language Control Panel and click to show the display language

list. Check your desired display language. Your selected display language will be

applied after rebooting.

How to set networking connection?

If you do not have IP shared server(direct link), you can select the icon

and press the right key of your mouse.

1. Show the networking connection status.

2. If you want to set the networking connection, you can press the right key of your

mouse to edit it.

Setting Up eJIFFY

Page 82

Step1 Select the icon , press the right key of your mouse, then select “Edit

Connection...” item.

Step2 Select the connection you want (eg. Wired) and click “+Add” button.

Types of connections

(1) Wired connection

Setting Up eJIFFY

Page 83

(2) Wireless connection

(3) DSL connection

Note: Details about eJIFFY please refer to eJIFFY in disk.

Setting Up eJIFFY

Page 84

Memo

Setting Up eJIFFY

Page 85

Chapter 8

Intel® Matrix Storage Manager RAID Configurations

The Intel® Matrix Storage Manager allows you to configure RAID 0, and 1 sets on the external Serial ATA hard disk drives.

Before creating a RAID set

Prepare the following items:

1. One SATA HDD.

2. A write-enabled floppy disk.

3. Microsoft

4. Motherboard support CD with Intel® Matrix Storage Manager driver.

Complete the following steps before you create a RAID set:

1. Install the external Serial ATA hard disk drive (HDD) on your system.

2. Set the Onboard SATA Mode item in the BIOS to .RAID..

See section “Integrated Peripherals” for details.

Windows® OS installation disk (Windows XP/Vista).

3. Enter the Intel® Matrix Storage Manager option to set up your RAID

4. Create an Intel® Matrix Storage Manager driver disk for Windows® OS

5. Install the Intel® Matrix Storage Manager driver after the Windows® OS

Intel® Matrix Storage Manager RAID Configurations

configuration.

installation. See section “Creating a RAID driver disk” for details.

had been installed.

Page 86

Entering Intel® Matrix Storage Manager RAID BIOS utility

1. During POST, press <Ctrl-I> to enter the Intel® Matrix Storage Manager RAID BIOS menu.

2. The main Intel® Matrix Storage Manager RAID BIOS menu appears.

3. Use the arrow keys to move the color bar and navigate through the items.

Intel® Matrix Storage Manager RAID Configurations

Page 87

Creating a RAID set

1. In the main Intel® Matrix Storage Manager RAID BIOS menu, highlight

Create RAID Volume using the up/down arrow key then press <Enter>.

2. When the RAID Level item is highlighted, use the up/down arrow key to

select the RAID set that you want to create.

When more than two HDDs are installed in your computer, the Disks item will be selectable. Then users can select the HDD that you want to belong to the RAID set. Please be noticed that selecting a wrong disk will result in losing the original data of the HDD.

3. Key in the RAID volume capacity. Use the up/down arrow to choose the

Intel® Matrix Storage Manager RAID Configurations

Capacity. The default value indicates the maximum capacity using the selected disks. Entering a lower capacity allows you to create a second volume on these disks.

Page 88

4. When done, press <Enter> to confirm the creation of the RAID set. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.

Pressing <Y> deletes all the data in the HDDs.

5. The following screen appears, displaying the relevant information about the RAID set you created.

Users please be noted that RAID 0 (Stripe) is set to accelerate the data access, and RAID 1 (Mirror) is set to provide the data backup. If you want to set RAID 0, you need to set the 2nd Boot Device item in the BIOS to Intel Volume0. See section “Advanced Setup” for details.

Intel® Matrix Storage Manager RAID Configurations

Page 89

Deleting a RAID set

1. In the main Intel® Matrix Storage Manager RAID BIOS menu, highlight

Delete RAID Volume using the up/down arrow key then press <Enter>.

2. Use the space bar to select the RAID set you want to delete.

Press the <Del> key to delete the set.

3. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.

Pressing <Y> deletes all the data in the HDDs.

Intel® Matrix Storage Manager RAID Configurations

Page 90

Resetting disks to Non-RAID

An HDD that has been previously configured as part of another RAID set

in another platform is called a broken RAID HDD. When you install a broken RAID HDD, you cannot select this disk when configuring a RAID set through the Intel use this broken RAID HDD as part of the RAID set configured through the Intel® Matrix Storage Manager, you may do so by resetting the disk to Non-RAID. You will, however, lose all data and previous RAID configurations.

To reset disks to Non-RAID:

1. In the main Intel® Matrix Storage Manager RAID BIOS menu, highlight

Reset Disks to Non-RAID using the up/down arrow key then press <Enter>.

2. Use the space bar to select the HDD to reset to Non-RAID.

3. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N>.

Pressing <Y> deletes all the data in the HDDs.

Matrix Storage Manager option. If you still want to

Exiting Setup

When you have finished, highlight Exit using the up/down arrow key then press <Enter> to exit the Intel® Matrix Storage Manager RAID BIOS utility.

A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press <N> to return to the Intel® Matrix Storage Manager RAID BIOS menu.

Intel® Matrix Storage Manager RAID Configurations

Page 91

Chapter 9

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

The 88SE9128 controller supports the creation of RAID 0 and RAID 1 virtual disks comprising of exactly two SATA physical disks.

The following shows the messages displayed during the POST of P67H2-A motherboard.

Press <Ctrl> + <M> to launch Marvell BIOS Utility.

To Create Virtual Disks

1. Enter the Topology pane, scroll the HBA 0: Marvell 0. Press Enter to select Configuration Wizard to begin creating the virtual disk.

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 92

2. Use the arrow keys to scroll the list of free disks. Press Space to select/unselect a disk and press Enter to continue. An asterisk will appear to the left of the selected disks.

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 93

3. Create Virtual Disk by configuring its settings in the Information pane.

4. Press Enter to select a RAID Level (RAID 0, RAID1).

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 94

5. Scroll to Stripe Size and press Enter to select 32K or 64K for the selected

RAID Level.

6. Scroll to Gigabyte Rounding and press Enter to select None, 1G or 10G.

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 95

7. Scroll to Quick Init and press Enter to select Yes or No.

8. Scroll to VD Name to type a new name, and press Enter to confirm the

selection.

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 96

9. Scroll to Next and press Enter to create the virtual disks after configuring the virtual disk. Then press Y to select YES.

The virtual disk is now listed in the Topology pane.

Marvell 88SE9128 SATA 6Gb/s RAID Controller BIOS Setup

Page 97

Chapter 10

Trouble Shooting

Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips.

a) System does not power up and the fans are not running.

1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Turn on again to see if the CPU and power supply fans are running.

2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.

3. Check the CPU FAN connector is connected to the motherboard.

4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.

5. Check the 12V power connector is connected to the motherboard.

6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.

2. Check the VGA adapter card (if applicable) is inserted properly.

3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps : memory not detected b. 1 long beep and 8 short beeps : VGA not detected

Trouble Shooting

Page 98

c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly.

2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.

Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.

1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.

2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.

3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

4. Remove the hard drive, optical drive or DDR memory to determine which of these component may be at fault.

Maintenance and care tips

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.

1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.

2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and areas of high moisture content.

3. Routinely clean the CPU cooler fan to remove dust and hair.

4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.

5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its lifespan.

6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.

Trouble Shooting

Page 99

Power Bu

on is pressed

but PC fails to start.

Yes

Check if Power Supply

Unit

(PSU) is working

Any Beep sound？

CLR CMOS and check

if CPU 12V power

is connected

art the PC stRe

Problem with PSU or board?

If board problem -> contact RMA

AC power cord is plu ed gg

and PSU switch is turned on?

Yes

oblem rBoard p

-> contact RMA

- If 3 short beeps:

DIMM memory not properly

inserted or memory failure

- If 1 long beep and 8 short beeps:

VGA not detected

Yes

Halt at POST screen？

Yes

R CMOLC S and restart.

If fail, contact RMA

Yes

Peripheral device issue

- HDD problem.

- CMOS setup error,

dnee to CLRCMOS.

System fail to start or unstable

er modify BIOS se

ng.

MCLR C OS and restart

Turn on PSU switch

or connect to wall socket

start. eand r

Check if monitor h sa

dis

play

Check if monitor

has display

Basic Troubleshooting Flowchart

Page 100

Memo