ECS P5TX-Bpro User Manual

P5TX-Bpro Mainboard

User’s Manual

Version 2.0
Copyright © July 1997 All rights reserved

This publication may not be copied, reproduced, translated, transmitted or reduced to any printed
or electronic medium or to any machine readable form, or stored in a retrieval system, either in
whole or in part without the written consent of the copyright holders.

The contents of this publication are subject to change. The manufacturer reserves the right to
alter the contents of this publication at any time and without notice. The contents of this publica­tion may contain inaccuracies or typographical errors and is supplied for informational use only.

Products are noted in this publication for identification purposes only. Microsoft is a registered
trademark and Windows is a trademark of Microsoft Corporation. Pentium is a trademark of Intel
Corporation. All other product names or brands may be trademarks or registered trademarks of
their respective holders.

P5TX–Bpro User’s Manual

Table Of Contents – III

Section 1: P5TX-Bpro Package & Product Information..........................1 - 1

About This Manual ...................................................................................................... 1 - 1

Package Contents .............................................................................................. 1 - 3

Component Information ..................................................................................... 1 - 5

Expansion Cards & Slots ............................................................................................ 1 - 5

Memory Sockets & Modules...................................................................................... 1 - 6

CPU Socket & CPU...................................................................................................... 1 - 6

Port & Controller Connections.................................................................................... 1 - 6

Section 2: Using Your Mainboard ......................................................... 2 - 1

System Controls.................................................................................................. 2 - 1

Hardware Controls & Indicators ................................................................................ 2 - 1

CMOS Setup Utility Controls .......................................................................................2 - 3

Hardware Features............................................................................................ 2 - 6

Onboard Ports ............................................................................................................2 - 6

Connectors..................................................................................................................2 - 6

Optional Hardware Connectors.................................................................................2 - 9

Firmware & Software .......................................................................................2 - 10

How To Use The CMOS Setup Utility........................................................................ 2 - 10

Clearing CMOS ......................................................................................................... 2 - 10

Flashing The BIOS ..................................................................................................... 2 - 12

Bus Master Drivers ................................................................................................... 2 - 12

Section 3: Reconfiguring Your Mainboard ...........................................3 - 1

Installing Expansion Cards .................................................................................. 3 - 1

ISA Cards & Slots ........................................................................................................ 3 - 1

Configuring Expansion Card Resources In CMOS Setup ..........................................3 - 2

Adding System Memory .................................................................................... 3 - 6

Memory Configurations .............................................................................................3 - 6

P5TX–Bpro User’s Manual

Table Of Contents – IV

Installing A CPU Upgrade .................................................................................. 3 - 9

The Basic Procedure...................................................................................................3 - 9

Configuring External Clock Speed & Factor............................................................. 3 - 10

Configuring CPU Voltage .......................................................................................... 3 - 10

CPU Jumper Tables & Illustrations........................................................................... 3 - 12

Adding An IDE Peripheral ................................................................................. 3 - 16

IDE Transfer Modes................................................................................................... 3 - 16

Installing IDE Devices ................................................................................................ 3 - 18

Section 4: P5TX–Bpro Reference Information......................................4 - 1

Using This Section...............................................................................................4 - 1

Jumper Configuration Summary........................................................................4 - 3

Supported CPUs ................................................................................................ 4 - 8

Interpreting CPU Markings.........................................................................................4 - 9

System Memory Specifications..........................................................................4 - 11

Memory Configurations ............................................................................................ 4 - 11

CMOS Setup Utility Summary...........................................................................4 - 12

Using the CMOS Setup Utility ................................................................................... 4 - 12

Accessing The CMOS Setup Utility ........................................................................... 4 - 12

Standard CMOS Setup.............................................................................................. 4 - 16

BIOS Features Setup ................................................................................................ 4 - 20

Chipset Features Setup............................................................................................ 4 - 25

Power Management Setup......................................................................................4 - 27

PNP/PCI Configuration ............................................................................................ 4 - 33

PC Health Monitor .................................................................................................... 4 - 41

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.1

In This Section:

About This Manual
Package Contents
Component Information

P5TX-Bpro Package & Product Information

This manual contains all the information you’ll need to use
the P5TX-Bpro mainboard. Please take a moment to familiarize
yourself with the design and organization of the manual.

About This Manual

This manual is divided into four sections:

• Section 1: Package & Product Information

A brief overview of what comes in the mainboard package, its

basic features, layout and component information.

• Section 2: Using Your Mainboard

Information on mainboard features that you may make use of

in operating your computer.

• Section 3: Reconfiguring Your Mainboard

How to change or upgrade the mainboard configuration.

• Section 4: Reference Information

A summary of the mainboard’s settings and specifications.

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.2

tant information. The icons appear in the sidebar and represent
the following:

The manual uses some icons to call your attention to impor-

G

C
D
N

• Important information

• A recommendation or good idea

• A warning or bad idea

• Danger warning

Online Manual Format

If the support disk for your mainboard is a CD-ROM disc, a
copy of the printed manual may be stored on the disc in Adobe
Acrobat format. If so, it requires Adobe Acrobat Reader version

3.0 or later to view it. Acrobat Reader for Microsoft Windows95
may also be supplied on the Support Disk. If not, you can obtain
a free copy of the Reader software from the Abobe web site which
is currently at www.adobe.com as well as other locations.

If you have the online manual, you may want to install Acro­bat Reader on your system hard disk. You can copy the manual
over as well so that the manual is readily available without hav­ing to hunt up the Support Disk when you want to view it.

If you are unfamiliar with Acrobat Reader, please take a mo­ment to view the Reader Online Guide which is available under
the Help menu when you run Reader.

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.3

Package Contents

items. Please inspect the package contents and confirm that ev­erything is there. If anything is missing or damaged, call your
vendor for instructions before proceeding. The package includes:

• P5TX–Bpro Mainboard

• Cable Pack:

• Support Disk:

eral Operating Systems. The drivers are organized in individual
folders by OS. In each folder there is a “readme” file that explains
how to install the driver. Please locate the folder for the driver
you need and check this file.

The P5TX–Bpro mainboard package contains the following

– 1 Floppy Controller Cable

– 1 IDE Controller Cable

– 9-pin Serial port & PS/2 Mouse port Port Bracket/cable

– 9-pin Serial port & Parallel port Port Bracket/cable

– Bus Master Drivers

– BIOS update Flash Utility

The mainboard comes with IDE Bus Master drivers for sev-

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.4

P5TX-Bpro Mainboard Layout

COM2

AT Keyboard

ISA Slots 1, 2, 3

JP2

J23

PCI Slots 1, 2, 3, 4

J22

COM1

Parallel

IDE2

IDE1

DIMMs 1, 2

Floppy

USB

Std. Power

SIMMs 1, 2, 3, 4

PS/2 Mouse

IR

J21

J16

JP1

J20

CPU Socket 7

J19 J18

Socket 7

JP3

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.5

Component Information

mainboard that you might need to know about if you want to
upgrade or change your system configuration. If your mainboard
is already installed in a system, it isn’t necessary for you to re­view this section.

that integrates many features onto the board including some num­ber of external ports.

Expansion Cards & Slots

sion or ‘add-on’ cards. Three of them are ISA slots, the other four
are PCI slots. When you get an expansion card, it must use one of
these to connect to the computer.

A T design. They are 16-bit slots that run at a moderate bus speed.
There are many kinds of expansion cards that use this slot design
to connect to the computer, some of the most common being
sound and modem cards.

tem expansion cards. They operate at a faster speed and have a
greater data throughput than ISA cards.

requires managing the system resource configuration. Most newer
expansion cards support the ‘Plug and Play’ standard that allows
an Operating System like Windows95 to automatically detect
them and configure system resources as needed. Some older ISA
designs may not support this standard and may therefore require
manual configuration. You should consult the specifications or
documentation for a card to determine if this is the case and what
needs do be done to properly configure the card.

This section is a brief description of the components on the

This mainboard uses the 2/3 Baby AT ‘form factor’, a design

The mainboard has seven expansion slots for system expan-

The ISA expansion slots are a legacy of the original IBM PC/

PCI slots are the current high-speed 32-bit standard for sys-

Expansion cards often make use of system resources, which

P5TX-Bpro User’s Manual

1: Package & Product Information – 1.6

Memory Sockets & Modules

They use 168-pin DIMM memory modules. The sockets func­tion independently of each other. This mainboard has a very flex­ible memory design that allows the use of a variety of memory
options up to a total of 256MB. There is more information about
this in Adding System Memory section of Section 3: Reconfiguring
Your Mainboard.

CPU Socket & CPU

class CPUs including MMX Pentiums
socket is easy . The lever at the side of the socket latches the CPU
in place when it is down and releases it when raised.

on the board for the first time, please refer to ‘Installing a CPU’ in
Section 3: Reconfiguring Your Mainboard.

Port & Controller Connections

two USB (Universal Serial Bus) ports and both a PS/2-type key­board and mouse port built onto the board. There are also sev­eral connectors built onto the board. There are connectors for
four IDE devices in two ‘channels’ and for two floppy disk drives.
There are also connectors on the board for some system case
features, CPU and other cooling fans and some other hardware
features.

formation.

There are three memory module sockets on the mainboard.

The Socket 7 CPU socket supports the full range of Pentium®-

®

. Installing a CPU in the

If you want to install a CPU upgrade or are installing a CPU

This mainboard has two external Serial ports, a Parallel port,

Details about these connectors are in Section 4: Reference In-

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.1

In This Section:

Using Your Mainboard

This section covers the following topics:

• System Controls & Indicators

• Hardware Features

• Firmware & Software

They go over the system control features and status indicators
that derive from the mainboard and explain the software that
comes with or is built-into the mainboard

System Controls
Hardware Features
Firmware & Software

System Controls

There are two topics in this section, a explanation of the hard­ware controls and status indicators that connect from the main­board to your system case and some information about the parts
of the CMOS Setup Utility that allow you customize some sys­tem features.

Hardware Controls & Indicators

There are some control features and status indicators that con­nect from the mainboard to your system case, which is some­times called the ‘Enclosure’ or ‘Chassis.’ These are:

• Power Status Indicator

• Suspend Switch

• Reset Switch

• Keyboard Lock

• Suspend Status Indicator

• Hard Disk Drive Activity Indicator

All of these case features connect to the mainboard via con­nectors J16, J18 and J19. Not all system cases have all of these
features, so your system may not have all of them. The functions
and options for these are shown in the table on the next page.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.2

Hardware Control & Indicator Connectors
Feature Function

Power Status LED When lighted indicates that system is turned on
Suspend Switch Puts the system into Suspend state under Operating

Systems that support this power management feature

Reset Switch Pressing the Reset switch restarts the system

Keyboard Lock Disables keyboard via a lock mounted on front panel of the case
Speaker Connects to the PC speaker mounted on the system case
Suspend LED When lighted indicates the system is suspended (J18)
HDD Activity LED Flashes when hard disk drive is active (J19)

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.3

CMOS Setup Utility Controls

T wo sections of the CMOS Setup Utility allow you to config­ure how some of your system’s features work. These are:

• BIOS Features Setup

• Power Management Setup

The CMOS Setup Utility is a program that is permanently
stored in the BIOS chip on the mainboard. The utility creates a
system hardware configuration record that it stores in a small
amount of battery-supported memory on the board. The BIOS
uses this record to function as an interface between the system
hardware and the operating system. Most of the settings in the
CMOS Setup Utility are made automatically, so you won’t nor­mally need to use this program. You can, however, customize
some of the operational features to suit how you prefer to use
the system.

The screen illustrations on the next two pages show the Setup
Default settings for these two sections of the utility.

The CMOS Setup Utility Summary in Section 4: Reference
Information, lists the setting options for each section of the util­ity including the two noted above.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.4

CMOS Setup Utility –

BIOS Features Setup
This section of the setup util­ity allows you to configure
some system features includ­ing Virus Warning, Boot Se­quence and Security Option.

Virus Warning –
When enabled, monitors the
primary hard disk boot sec­tor and warns of any attempt
to write to it.
Boot Sequence –
Controls the order in which
the system checks disk drives
for a boot disk.

Security Option –
Sets the level of password
protection for the system.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.5

CMOS Setup Utility –

Power Management Setup
This section of the setup util­ity allows you to configure the
power management features
supported by the BIOS. These
can also operate in tandem
with Operating System power
management features.

You can use the Min Saving
or Max Saving default modes
or you can configure the
power management features
individually in the User Define
mode.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.6

Hardware Features

This section is a brief overview of information about the
mainboard’s hardware features that connect to external devices.

Onboard Ports

There are five external ports on the mainboard. These are ports
standard to most personal computers:

• COM1 Serial Port

A high-speed serial port which can also be configured as the

COM3 port in the CMOS Setup Utility.

• COM2 Serial Port

A high-speed serial port which can also be configured as the

COM4 port in the CMOS Setup Utility.

• Parallel Port

The parallel port can be configured as a Standard, ECP or EPP

parallel port in the CMOS Setup Utility

• PS/2 Keyboard Port & PS/2 Mouse Port (stacked)

• USB ports – two ports (stacked)

Connectors

There are several connectors on the mainboard for connecting
additional ports and internal peripheral devices

• IDE 1 – Primary IDE Channel

Connector for the Primary Master and Slave IDE devices.

• IDE 2 – Secondary IDE Channel

Connector for the Secondary Master and Slave IDE devices.

• Floppy Connector

Connector for two floppy disk drives.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.7

CMOS Setup Utility –

Integrated Peripherals
This section of the setup util­ity configures the IDE and
Floppy controllers and the
settings for the external ports

This section enables and con­figures the optional USB and
Infrared features.

The screen illustration shows
the settings when Setup De­faults are loaded.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.8

Cooling Fan Connectors

There are three cooling fan connectors on the mainboard that
support cooling fans for the CPU, power supply and a fan
mounted on the system case. If you connect fans to these con­nectors, and the ‘CPU FAN Off In Suspend’ line in the CMOS
Setup utility’s Power Management Setup section is set to Enabled,
the system will turn the fans off when the system is in Suspend
mode. The system power supply must have a separate fan power
connector to support this feature.

“PC Health” Monitoring

In order to detect potentially damaging conditions while the
mainboard is operating, the mainboard has an onboard sensor
that monitors temperature and voltage levels. In the event that
these exceed predefined limits, the system will automatically re­act in attempt to prevent damage.

The PC Health Monitor section of the CMOS Setup utility
sets the controls for this feature and also displays data from the
onboard sensor.

UltraDMA Hard Disk Drive Support

This mainboard supports hard disks that use UltraDMA data
transfer. You attach an UltraDMA drive to one of the IDE cables.
If you use the Optimum Settings feature in the CMOS Setup
utility the system will automatically detect the drive and config­ure the system to use it.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.9

Optional Hardware Connectors

There are additional feature connectors on the mainboard for
optional ports. These require optional external port hardware.

USB Ports

The USB connector on the mainboard supports two Univer­sal Serial Bus ports. An optional external port bracket attaches to
the onboard connector via an attached cable.

With the optional port bracket installed you can attach USB
devices to the external ports. If the USB ports are installed, the
USB Keyboard Support line in the Integrated Peripherals section
of the CMOS Setup utility must be set to ‘Enabled’. USB ports
may also require Operating System support for USB devices.

IR Ports

There is one standard and one optional connector on the main­board which support an IR (infrared) port module that enables
wireless communication between the computer and other com­puters and devices with an infrared port. The default IR connec­tor, J11, is for HPSIR or ASKIR and the optional J10 connector is
for Fast IR..

The port module is an optional component. If it is installed,
you must set the UART 2 line in the Integrated Peripherals sec­tion of the CMOS Setup utility to the appropriate IR mode used
by the module.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.10

Firmware & Software

The mainboard hardware is supported by both firmware and
software components. Firmware is software that is stored on a
chip on the board rather than on disk media.

The firmware component you interface with on this main­board is the CMOS Setup Utility. This utility establishes various
settings used by the BIOS, the basic software that is an interface
between the system hardware and software.

The software component is comprised of software drivers that
support the PCI IDE controller and some of the other hardware
features.

How To Use The CMOS Setup Utility

The CMOS Setup Utility options are listed in detail in Section
4: Reference Information. This section is just a brief explanation
of how to run the program to adjust settings as noted in this and
the next section.

To run the CMOS Setup Utility, press the Del or Delete key
while the computer is starting up, before the operating starts to
load. The utility’s main screen will appear as shown on the next
page. To navigate the program, use the controls shown on the
screen. The utility has several sections. Many of the features con­figured by the utility are set to operate automatically when the
‘Setup Defaults’, the recommended mode, are used. With Setup
Defaults loaded you can still customize various settings.

Clearing CMOS

Under some unusual circumstances the configuration record
created by the CMOS Setup utility and stored on the mainboard
can become corrupted and unusable, possibly leading to the board
being unable to operate properly. If this happens, the CMOS
record can be cleared by setting jumper JP2 to the clear setting for
a moment and then setting it back to the Normal setting. Refer to
the Jumper Summary in Section 4 for more information.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.11

CMOS Setup Utility –

This is the main screen for the
setup utility from which you
access its various sections.
The function and use of each
section is covered in Section
4: Reference Information.

P5TX–Bpro User’s Manual

2: Using Your Mainboard – 2.12

Flashing The BIOS

This mainboard uses the Award BIOS. The BIOS is stored on
a programmable flash memory chip on the mainboard. Updates
to the BIOS can be installed by installing a new BIOS file on the
flash chip, which replaces the existing one. You do this using
software that comes on the Support Disk. There is an explana­tion of how to install a BIOS update in a ‘readme’ text file in­cluded with the program.

Bus Master Drivers

This mainboard comes with software drivers, for various Op­erating Systems, that enable the PCI controller to operate in ‘Bus
Master’ mode. The drivers are on the Support Disk. The included
‘readme’ file has information on the drivers and installation in­formation.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.1

In This Section:

Installing Expansion Cards
Adding System Memory
Installing A CPU Upgrade
Adding An IDE Peripheral

Reconfiguring Your Mainboard

This section explains how to install new hardware on your
mainboard. It covers installing expansion cards, adding system
memory , changing the CPU and installing additional IDE periph­eral devices such as a hard disk or a CD-ROM drive.

Installing Expansion Cards

There are seven expansion card slots on the mainboard, three
ISA slots and four PCI slots. When you get an expansion card, it
will come with instructions on how to install it, so this section
covers relevant information from the mainboard side only.

ISA Cards & Slots

ISA expansion cards often use system resources in the form of
IRQs and DMA channels. Newer cards that comply with the Plug
and Play (PnP) standard are designed to allow the Operating Sys­tem to automatically configure system resources. Cards that do
not support PnP may require manual configuration of both the
card hardware and settings in the CMOS Setup Utility.

If you have a PnP-compliant card to install there should be
little to do other than follow the installation instructions. If, how­ever, you have a non-PnP card and it requires configuring system
resources, you may need to review the third part of this section,
Configuring Expansion Card Resources In CMOS Setup.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.2

PCI Cards & Slots

likely to get will be Plug an Play compliant. If you are using an
Operating System that supports PnP, such as Windows 95, you
should be able to follow the installation instructions that come
with the card and have the Operating System automatically rec­ognize and configure the card.

capability. For installed PCI cards to use this feature an Operat­ing System-specific Bus Master software driver that comes with
this mainboard must be installed under your Operating System.
These drivers are located on the Support Disk. There is more
information about them later in this section.

With very few exceptions, any PCI expansion card you are

The four PCI slots on the mainboard all have ‘Bus Master’

Running CMOS Setup

To run the CMOS Setup utility,
press the Delete or the Del
key while your computer is
first starting up. Select the
‘PNP/PCI CONFIGURATION’
item on the main screen and
press the Enter key to open it.
When you are finished, press
the Esc key once to return to
the main screen and then
select ‘SAVE & EXIT SETUP’ and
press the Enter key to save the
new configuration. For more
information on this see Sec­tion 4: Reference Information.

Configuring Expansion Card Resources In CMOS Setup

The CMOS Setup Utility , which is covered in detail in Section
4: Reference Information, has a section called PNP/PCI Configu­ration. The default settings in this section allow the Operating
System to automatically configure IRQ resources for PnP com­pliant ISA and PCI Cards.

If you need to install a non-PnP card, you will need to config­ure any IRQ and DMA settings manually, both on the card and
in the CMOS Setup Utility . The following three pages show how
to do this.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.3

CMOS Setup Utility –

PnP/PCI Configuration
This is the default screen for
this section when Setup De­faults are loaded. If you need
to manually configure the IRQ
settings, set the first item on
the screen to the ‘Manual’
setting. See the next page.

If you install an Operating Sys­tem that supports Plug and
Play, such as Windows95,
you should set the first line,
‘PNP OS Installed’ to ‘Yes’.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.4

CMOS Setup Utility –

PnP/PCI Configuration
When ‘Resources Controlled
By’ is set to ‘Manual’ you can
individually configure the IRQ
& DMA channel settings. The
individual defaults are for PnP
cards and will still use all the
items listed to automatically
assign resources as needed.

If you are installing a ‘legacy’
ISA card that requires manual
configuration, you can manu­ally assign the required re­sources as needed. See the
next page for an example.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.5

CMOS Setup Utility –

Pnp/PCI Configuration
This screen shows an ex­ample of a manually config­ured IRQ setting for a “Legacy’
ISA expansion card. Legacy
cards, by definition, are not
PnP compliant and must be
manually configured if they
require an IRQ or DMA chan­nel. See the card manual for
specifics.

When an item in the list is con­figured this way, it is no longer
part of the pool of automati­cally configurable resources.
For this reason, don’t config­ure ISA cards this way unless
they are Legacy cards.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.6

N

You can not use SIMM and
DIMM modules at the same
time on this mainboard.

D

It is possible to install more
memory than the board sup­ports, e.g. four 128MB SIMM
modules would total 512MB,
but the board would ignore
256MB of that. Do not install
more than 256MB on this
mainboard.

Adding System Memory

There are some requirements you must follow if you want to
install system memory . The memory subsystem has four 72-pin
SIMM sockets divided into two banks, SIMM1 & SIMM2 and
SIMM3 & SIMM4. It also has two DIMM sockets. You cannot
use SIMMs and DIMMs at the same time on this mainboard.

SIMM modules should use either Fast Page Mode (FPM) or
EDO 5-Volt DRAM. You can use modules from 4MB to 128MB,
either single or double-sided. DIMM modules must use 3.3-Volt
EDO or SDRAM.. Total supported memory capacity is 256MB.

If your mainboard is already installed in a system, it will have
some amount of memory installed on the board. You can tell
how much by checking the configuration screen that appears
when the computer is starting up. With some memory installed,
there may be sockets available to add additional memory. If not,
you must remove modules to install an upgrade.

Memory Configurations

SIMMs install in pairs. You can install any SIMM memory
combination as long as you follow the basic requirement of in­stalling identical modules in both sockets of a bank, i.e.:

• 5-Volt modules

• Both modules are the same size, e.g. 16MB (MegaBytes)

• Both are the same DRAM memory type, e.g. EDO

• Both use the same operating speed, e.g. 60ns (nanoseconds)

Each DIMM is a memory Bank. You can install DIMMs with
these specifications:

• 8MB to 128 MB single or double-sided module

• 3.3-Volt module

• EDO or SDRAM DRAM

Other than these requirements, there is no limitation on the
variety of possible combinations, so they are not listed here.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.7

DIMMs 1, 2

Retaining Clips

SIMMs 1, 2, 3, 4

Socket 7

Memory Sockets

The picture above shows the
memory module sockets in
detail. The DIMM sockets are
numbered DIMM1 & DIMM2
as noted.
Modules press into place
and are held in position by a
retaining clamp at each end
of the socket.

When you want to remove a
module, press down on the
retaining clamps to push the
module out of the socket.

The SIMM sockets are num­bered SIMM1 to SIMM4 as
noted. You must install mod­ules in pairs in either sockets
1 & 2 or 3 & 4.

Retaining Clamps

Modules snap into place and
are held in position by a re­taining clip at each end of the
SIMM socket.
When you want to remove a
module, press down on the
retaining clips to release the
module from the socket.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.8

Installing Memory Modules

entation. If you have trouble inserting the connector edge of a
module into a socket, it may be oriented the wrong way. Turn
the module around and try again. You shouldn’t need to force it.

45° angle and then push it up into the retaining clips so that it
snaps in place and is at a 90° angle to the board.

position of the shorter section of the connector edge that plugs
into the DIMM socket. Note the position of the shorter section
of the socket. Orient the module so that these match and press
the module into the socket at a 90° angle. The retaining clamps at
each end of the socket will rotate upwards automatically.

If All Sockets Are Occupied

available, you must remove some installed modules and replace
them with upgrade modules.

memory is already installed. In some cases, there may be a mix
of module types. You can tell this by checking the configuration
screen that appears while the computer is starting up.

and replace them with the upgrade. EDO is faster than Fast Page
and SDRAM is faster than EDO. For example, if you have the
following configuration and you plan to install two 16MB EDO
SIMM modules:

are lower performance and replace them with the memory up­grade, resulting in the greatest performance gain.

Modules are designed so that they will only insert in one ori-

To install a SIMM module, insert it into the socket at about a

To install a DIMM module, look at the module and note the

If you want to install more memory and there are no sockets

If you have to do this, make sure to identify what type of

Remove the lowest performance and smallest size modules

• SIMM 1 & 2: 8MB Fast Page mode modules

• SIMM 2 & 3: 8MB EDO modules

You should remove the two 8MB FP modules because they

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.9

Installing A CPU Upgrade

installed unless your vendor installed one when you purchased
the board. If the mainboard is installed in a system, there will
already be a CPU installed. In either case the information and
procedure for installing a CPU is the same. Since the more likely
scenario is that you are installing an upgrade, this section assumes
that is what you are doing.

The Basic Procedure

board for a specific CPU by doing the following:

on the board. In order to do this, you will need to know some
information about the CPU you plan to install. This should be
provided by the CPU vendor or by the vendor you buy the chip
from. You’ll need the following information:

process data and is the one used by CPU manufacturers to indi­cate the speed of the chip, for example, a 133MHz Intel Pentium
The CPU also has an external clock speed which is the speed at
which it interacts with external components.

or it may be split, depending on the CPU design. Some proces­sors use one voltage for the ‘core’ (Vcore) and another for input/
output (Vio).

If you are installing this mainboard it will not have a CPU

To install a CPU on this mainboar d you need to set up the

• Set the External Clock Speed

• Set the Clock Multiplier Factor

• Set the CPU Voltage

You configure the CPU settings by adjusting jumper settings

• CPU Internal Clock Speed

• CPU Voltage

The internal clock speed is the speed the CPU operates at to

®

CPU voltage may either be the same internally and externally

.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.10

Configuring External Clock Speed & Factor

have to set the external clock speed (sometimes referred to as the
bus speed) and the clock factor so that the result is the internal
clock speed of the CPU you are installing. For example, the de­fault setting for these is:

at is fixed, the two factors, external clock and clock factor, are the
variables. The CPU manufacturer or vendor’s information should
tell you what these factors should be.

P Rated CPUs

performance rated at an Intel Pentium
tually have a slower internal clock speed. This ‘P’ rating is used
to indicate the CPU’s performance rather than its internal clock
speed. For example, the Cyrix/IBM P166 has an actual internal
clock speed of 133MHz. If you install a CPU of this type, make
sure you set the mainboard for the actual internal clock speed of
the CPU, not its P rating.

To configure the board for a CPU’s internal clock speed, you

66.6MHZ [external clock] x 2.0 [clock factor] =133.2MHz

or, an effective setting of 133MHz.

Since the internal clock speed the CPU is supposed to operate

Cyrix, IBM and AMD all make Pentium®-class CPUs that are

®

equivalent speed but ac-

Configuring CPU Voltage

The CPU voltage specification should also be provided in in­formation from the manufacturer or vendor. Standard Pentium
CPUs are single voltage. MMX Pentiums® are dual-voltage. You
should set the CPU Voltage jumpers according to the specifica­tions you get with the CPU.

®

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.11

CPU Settings

Internal Clock External Clock Clock Factor
Intel Pentium CPUs (Including MMX)

75MHz 50MHz x 1.5
90MHz 60MHz x 1.5
100MHz 66.6MHz x 1.5
120MHz 60MHz x 2.0
133MHz 66.6MHz x 2.0
150MHz 60MHz x 2.5
166MHz 66.6MHz x 2.5
200MHz 66.6MHz x 3.0
233MHz 66.6MHz x 3.5

Cyrix/IBM CPUs
6X86 & 6X86L – 6X86MX –
P120+ (100MHz) 50MHz x 2.0 PR166MHz (150MHz) 60MHz x 2.5
P133+ (110MHz) 55MHz x 2.0 PR200MHz (166MHz) 66.6MHz x 2.5
P150+ (120MHz) 60MHz x 2.0 PR233MHz (200MHz) 66.6MHz x 3.0
P166+ (133MHz) 66.6MHz x 2.0 PR233MHz (188MHz) 75MHz x 2.5
P200+ (150MHz) 75MHz x 2.0 PR266MHz (225MHz) 75MHz x 3.0

AMD CPUs
K5

PR75 (75MHz) 50MHz x 1.5
PR90 (90MHz) 60MHz x 1.5
PR100 (100MHz) 66.6MHz x 1.5
PR120 (120MHz) 60MHz x 2.0
PR133 (133MHz) 66.6MHz x 2.0
PR150 (150MHz) 60MHz x 2.5
PR166 (166MHz) 66.6MHz x 2.5
K6
PR166 (166MHz) 66.6MHz x 2.5
PR200 (200MHz) 66.6MHz x 3.0
PR233 (233MHz) 66.6MHz x 3.5

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.12

C

In practice, for an Off setting
on a two-pin jumper, place
the cap over one pin so that it
doesn’t get lost.

CPU Jumper Tables & Illustrations

The next few pages show the CPU jumper settings. The set­tings are listed in the tables as follows:

• Where two pins are shorted (connected) by a jumper cap on a

three-or-more-pin jumper the shorted pins are listed, e.g. 1-2

or

• For a two-pin jumper, On, if the cap is in place, and Off, if the

cap is not in place.

In the jumper illustrations, the Pin 1 position is shaded and
the jumpers, shown in a “bird’s eye” view, look like this:

A jumper with a cap in position looks like this:

The default settings are noted in the tables.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.13

CPU Jumper Settings
Function Jumper Settings

External Speed JP1 Ext. Clock Bus Speed

50MHz 25MHz 11-13, 19-21,20-22
55MHz 27.5MHz 11-13, 17-19,20-22
60MHz 30MHz 9-11, 19-21,20-22

66.6MHz 33.3MHz 11-13, 19-21,18-20 [D]

68.5MHz 34.25MHz 9-11, 17-19,18-20
75MHz 37.5MHz 9-11, 17-19,20-22

83.3MHz 41.5MHz 11-13, 17-19,18-20

Note: JP1 has two sections, one for External Clock Speed and the other for Internal Clock Factor
Internal Clock Factor JP1 1.5x & 3.5x 1-3, 2-4

2.0x 1-3, 4-6

2.5x 3-5, 4-6 [D]

3.0x 3-5, 2-4

Note: JP1 has two sections, one for External Clock Speed and the other for Internal Clock Factor
CPU Core Voltage JP3 1-2 3-4 7-8 9-10 11-12

On= Cap On 2.5V On
(One cap for this jumper) 2.8V On [D]

2.9V On

3.2V On

3.52V On

[D] = Default Setting

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.14

Internal Clock Factor

1.5x & 3.5x
JP1

12
56
910
13 14
17 18
21 22
50MHz 55MHz 60MHz 66.6MHz

External Clock Speed

JP1

12
56
910
13 14

2.0x
JP1

12
56
910
13 14
17 18
21 22

2.5x

12
56
910
13 14
17 18
21 22

CPU Core Voltage (Vcore)

2.5V
11

12

JP1

3.0x
JP1

12
56
910
13 14
17 18
21 22

JP3

1

2

2.8V
11

12

JP1

12
56
910
13 14
17 18
21 22

68.5MHz

JP3

1

2

JP1

12
56
910
13 14
17 18
21 22
75MHz

2.9V
JP3

11

12

1

2

17 18
21 22

83.3MHz

3.2V
11

12

JP3

3.52V
JP3

1

2

11

12

1

2

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.15

Jumper Locations

This illustration shows the lo­cation of the jumpers illus­trated on the previous page.

JP1

Socket 7

JP3

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.16

Adding An IDE Peripheral

ripheral devices as they relate to the mainboard. The onboard
Enhanced IDE controller supports up to four devices, two per
IDE channel. The primary hard disk drive in most systems is an
IDE device. You may want to install more hard disks, a CD-ROM
drive or combination of these and other devices. This mainboard
supports both PIO and UltraDMA modes, which it can detect
automatically. You can install a mix of devices. With the Setup
Defaults loaded in the CMOS Setup utility , the system will auto­matically detect and configure multiple devices of whatever mode.

IDE Transfer Modes

board chipset. The transfer of data between the hard disk and the
system takes place using one of a number of transfer modes –
either one of several PIO modes or UltaDMA mode.

mainboard supports all of them, most current hard disk and CD­ROM drives use either Mode 3 or 4. The greater the mode num­ber, the faster the transfer rate, so you should use the fastest mode
the device can operate at. With Setup Defaults loaded in the
CMOS Setup Utility, the system will automatically detect the
fastest mode a device can use and set it for that mode.

data transfer than PIO modes. To use it you must install a drive
that uses this transfer method. Drives that use PIO Mode transfer
can not use the UltraDMA setting.

section of the CMOS Setup utility . The screen illustration at right
shows the Setup Defaults settings.

This section covers some aspects of installing internal IDE pe-

Hard disk read and write operations are executed via the main-

Although there are several PIO Modes (0 through 4), and this

UltraDMA is another transfer method that provides even faster

The settings for drive modes are in the Integrated Peripherals

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.17

CMOS Setup Utility –

Integrated Peripherals
The illustration above shows
the Setup Defaults settings for
this screen. Y ou can install IDE
devices under these settings
and the system will automati­cally detect and set the best
mode for each device.

You can also set the transfer
mode for each device manu­ally, although we recom­mend using the default set­tings unless you have a rea­son not to and you know what
you are doing.

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.18

Installing IDE Devices

vices in two channels, IDE1 and IDE2. These are called the Pri­mary and Secondary IDE channels.

the Master device and the second the Slave device. You must
configure any IDE device you install to operate as one or the
other. To find out how to configure the device you plan to install
you should refer to the manual that comes with the device. You
may need to set jumpers or switches to configure it.

IDE Cables

two devices to the mainboard. If you need to install devices on
the second channel you will need to get another IDE cable. These
are a standard and inexpensive item that you can generally find
at any computer supply store. One edge of the cable is colored to
indicate the Pin 1 side. When you connect the cable to the main­board and a device you must orient the cable so that this colored
edge is at the Pin 1 side of the connector you are attaching it to.

ensure correct orientation, and the supplied cable has an orienta­tion tab on the side of the connector. Some IDE cables do not
have this tab and therefore are not forced to use the correct orien­tation. You should check that any cable you buy has orientation
tabs on the side of the connectors. If you get a cable that does not
have them, make sure the cable is correctly oriented when you
attach it to the board and the device.

The mainboard’s Enhanced IDE controller supports four de-

Each channel supports two devices, the first device is called

The mainboard comes with one IDE ribbon cable to connect

The mainboard IDE connectors have an orientation cut-out to

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.19

and one in-between, closer to one of the ends. When you install
a device on the second channel, attach the lone end to the IDE2
connector on the mainboard. The two connectors that are closer
to each other are for connecting to IDE devices. The connector
on the end is for the Master device and the connector in the middle
is for the Slave device.

IDE Devices & CMOS Setup

automatically detected by the BIOS and entered in the Standard
CMOS Setup section of the CMOS Setup utility if you use the
Setup Defaults, which automatically detect any new hard disk
drive. All other devices do not use drive parameters and will not
show up in the device list on this page.

IDE cables have three connectors on them, one at each end

When you install a new hard disk drive its parameters will be

P5TX–Bpro User’s Manual

3: Reconfiguring Your Mainboard – 3.20

P5TX–Bpro User’s Manual

4: Reference Information – 4.1

In This Section:

Jumper Summary
Connector Summary
CPU Information
Memory Configurations

P5TX–Bpro Reference Information

This section is a summary of the P5TX–Bpro’s specifications

and settings. It includes the following:

• Jumper Configuration Summary

• Connector Summary

• Supported CPUs

• System Memory Configuration Specifications

• CMOS Setup Utility Summary

CMOS Setup Utility

Using This Section

The information in this section is presented in a summary for­mat to make it easy to find specific information. If you need re­lated explanations, please refer to the topics earlier in the manual.

P5TX–Bpro User’s Manual

4: Reference Information – 4.2

ISA Slots 1, 2, 3

PCI Slots 1, 2, 3, 4

J22

COM1

Parallel

IDE2

COM2

IDE1

DIMMs 1, 2

AT Keyboard

Floppy

USB

Std. Power

SIMMs 1, 2, 3, 4

PS/2 Mouse

IR

JP2

J21

J16

JP1

J23

J20

CPU Socket 7

J19 J18

Socket 7

JP3

P5TX–Bpro User’s Manual

4: Reference Information – 4.3

C

In practice, for an Off setting
on a two-pin jumper, place
the cap over one pin so that it
doesn’t get lost.

Jumper Configuration Summary

This section lists the jumper setting options for this mainboard.
The settings are listed as follows:

• The two pins shorted by a jumper cap on a three-or-more-pin

jumper, e.g. 1-2

or

• For a two-pin jumper, On, if the cap is in place, and Off, if a

cap is not in place.

In the jumper illustrations, the Pin 1 position is shaded and
the jumpers, shown in a “bird’s eye” view, look like this:

A jumper with a cap in position looks like this:

The default settings are noted in the summary tables. Unless
you need to upgrade the CPU, disable the onboard VGA feature
or upgrade the BIOS, you should not need to change them.

Jumper & Connectors

The illustration at left shows
the location of the jumpers,
ports and other connectors
on the mainboard.

P5TX–Bpro User’s Manual

4: Reference Information – 4.4

CPU Jumper Settings
Function Jumper Settings

External Speed JP1 Ext. Clock Bus Speed

50MHz 25MHz 11-13, 19-21,20-22
55MHz 27.5MHz 11-13, 17-19,20-22
60MHz 30MHz 9-11, 19-21,20-22

66.6MHz 33.3MHz 11-13, 19-21,18-20 [D]

68.5MHz 34.25MHz 9-11, 17-19,18-20
75MHz 37.5MHz 9-11, 17-19,20-22

83.3MHz 41.5MHz 11-13, 17-19,18-20

Note: JP1 has two sections, one for External Clock Speed and the other for Internal Clock Factor
Internal Clock Factor JP1 1.5x & 3.5x 1-3, 2-4

2.0x 1-3, 4-6

2.5x 3-5, 4-6 [D]

3.0x 3-5, 2-4

Note: JP1 has two sections, one for External Clock Speed and the other for Internal Clock Factor
CPU Core Voltage JP3 1-2 3-4 7-8 9-10 11-12

On= Cap On 2.5V On
(One cap for this jumper) 2.8V On [D]

2.9V On

3.2V On

3.52V On

Other Jumper Settings

Clear CMOS JP2 Default Normal 2-3 [D]

Clear 1-2*

* Put cap on jumper for a moment and then remove to clear current settings

[D] = Default Setting

P5TX–Bpro User’s Manual

4: Reference Information – 4.5

Internal Clock Factor

1.5x & 3.5x
JP1

12
56
910
13 14
17 18
21 22
50MHz 55MHz 60MHz 66.6MHz

External Clock Speed

JP1

12
56
910
13 14

2.0x
JP1

12
56
910
13 14
17 18
21 22

CPU Core Voltage (Vcore)

2.5V
11

2.5x

12
56
910
13 14
17 18
21 22

JP3

1

JP1

3.0x
JP1

12
56
910
13 14
17 18
21 22

2.8V
JP3

11

JP1

12
56
910
13 14
17 18
21 22

68.5MHz

2.9V
JP3

1

11

JP1

12
56
910
13 14
17 18
21 22
75MHz

1

17 18
21 22

83.3MHz

12

3.2V
11

12

JP3

2

1

2

12

3.52V
JP3

11

12

2

1

2

12

Clear CMOS
JP2

1

Normal Clear

2

JP2

1

P5TX–Bpro User’s Manual

4: Reference Information – 4.6

Onboard Connectors
Name Function Description

J1 PS/2 Mouse Optional PS/2 Mouse port

(not present if AT keyboard por t installed)

J2 PS/2 Keyboard Optional PS/2 Keyboard port

(not present if AT keyboard por t installed)
J3 AT Keyboard Port Connects to AT Keyboard
J4 PS/2 Mouse port Connects to PS/2 mouse port bracket cable
J5 USB Ports Connector for Universal Serial Bus 2-port bracket
J6 First IDE Channel 40-pin connector connects to 2-device cable;

End device is Primary Master, middle is Slave
J7 Second IDE Channel 40-pin connector connects to 2-device cable;

End device is Secondary Master, middle is Slave
J8 COM1 Port Onboard 9-pin serial port is COM1, can be set to COM3
J9 COM2 Port Onboard 9-pin serial port is COM2, can be set to COM4
J10 FIR header (optional) Connects to optional Fast IR infrared module cable
J11 Intel IR header Connects to optional IrDA or ASKIR infrared module cable
J12 Parallel Port 25-pin parallel port supports enhanced modes
J13 Floppy Drive Controller 34-pin connector connects to 2-device cable;

End device is Drive A:, middle is Drive B:
J14 PS/1 Power Connects to standard power supply leads P8 & P9
J16 Case Features Connects to case features:

Pin 2-3:Power On LED; Pin 4-5: Suspend Switch;

Pin 9-10: Reset Switch;

Pin 11-15: Keyboard Lock; Pin 17-20: Speaker

P5TX–Bpro User’s Manual

4: Reference Information – 4.7

Name Function Description

J18 Suspend Mode LED Connects to case front panel Suspend mode LED;

LED blinking indicates low-power suspend mode is active
J19 Hard Disk LED Connects to case front panel hard disk activity LED
J20 Case Fan power For case-mounted cooling fan power cable (+12V)
J21 CPU Fan power For CPU cooling fan power cable (+12V)
J22 Power Fan power Connects to lead from “green” power supply with power

management-enabled cooling fan
J23 Intrusion Detector Connects to chassis intrusion cable

J22: Case Features Connector

3–25–410–9

15 – 1120 – 17

Pins 2-3: Power On LED
Pins 4-5: Suspend Switch
Pins 9-10: Reset Switch
Pins 11-15: Keyboard Lock
Pins 17-20: Speaker

P5TX–Bpro User’s Manual

4: Reference Information – 4.8

Supported CPUs

This mainboard can use CPUs from Intel, Cyrix, IBM and
AMD. The board’ s switching CPU power design and jumper con­figuration options allow the use of all Pentium class processors
from all three vendors, including those with MMX features. The
correct jumper configuration automatically sets the required
power configuration for the CPU.

Processor speeds from 90 to 233MHz are supported as well as
single and split voltage CPUs.

Intel CPUs Supported:

Pentium P54C, P54CTB, P54CT, P55C

Cyrix & IBM CPUs Supported:

6X86, 6X86L, 6X86MX

AMD CPUs Supported:

K5, K6

P5TX–Bpro User’s Manual

4: Reference Information – 4.9

AMD K5 CPU Markings

P–Rating: 75, 90, 100, 120, 133, 150, 166

Interpreting CPU Markings

If you are installing a CPU and you do not have the informa­tion needed to set the CPU jumper configuration you can usually
get it from the makings on the CPU. The following information
is a guide to reading the markings.

Package Type
A=SPGA (296-pin)

AMD – K5 – PR100 A B Q

100MHz

Internal Clock Speed

Operating Voltage
B = 3.45V ~ 3.60V
C = 3.30V ~ 3.465V
F = 3.135V ~ 3.465V

(Vcore/Vio)
H = 2.76V ~ 3.0V / 3.135V ~ 3.465V
J = 2.57V ~ 2.84V / 3.135V ~ 3.465V
K = 2.38V ~ 2.63V / 3.135V ~ 3.465V

CPU Model

Case Temperature
Q = 60°C
R = 70°C
W = 55°C
X = 65°C
Y = 75°C
Z = 85°C

P5TX–Bpro User’s Manual

4: Reference Information – 4.10

Cyrix 6x86 CPU Markings

P–Rating: 90+, 120+, 133+, 150+, 166+, 200+

CPU Model

6x86

6x86L

Core Voltage
Range Midpoint

3.3V

3.52V

2.5V

2.7V

6x86 – P166+ GP
133MHz

3.52V (028)

VCC Specification
Full-spec = 3.15V ~ 3.7V
C-spec (16) = 3.15V ~ 3.45V
C-spec (028) = 3.4V ~ 3.7V

Internal Clock Speed (Core Frequency)
100, 110, 120, 133, 150

P5TX–Bpro User’s Manual

4: Reference Information – 4.11

N

You can not use SIMM and
DIMM modules at the same
time on this mainboard.

System Memory Specifications

The memory subsystem has four 72-pin SIMM sockets di­vided into two banks, SIMM1 & SIMM2 and SIMM3 & SIMM4.
It also has two DIMM sockets. You cannot use SIMMs and
DIMMs at the same time on this mainboard.

SIMM modules should use either Fast Page Mode (FPM) or
EDO 5-Volt DRAM. You can use modules from 4MB to 128MB,
either single or double-sided. DIMM modules must use 3.3-Volt
EDO or SDRAM.. Total supported memory capacity is 256MB.

Memory Configurations

SIMMs install in pairs. You can install any SIMM memory
combination as long as you follow the basic requirement of in­stalling identical modules in both sockets of a bank, i.e.:

• 5-Volt modules

• Both modules are the same size, e.g. 16MB (MegaBytes)

• Both are the same DRAM memory type, e.g. EDO

• Both use the same operating speed, e.g. 60ns (nanoseconds)

Each DIMM is a memory Bank. You can install DIMMs with
these specifications:

• 8MB to 128 MB single or double-sided module

• 3.3-Volt module

• EDO or SDRAM DRAM

Other than these requirements, there is no limitation on the
variety of possible combinations, so they are not listed here.

Note: It is possible to install more memory than the board
supports. Do not install more than 256MB on this mainboard,
the system will ignore additional memory.

P5TX–Bpro User’s Manual

4: Reference Information – 4.12

CMOS Setup Utility Summary

This section explains the entries in the CMOS Setup Utility
program. This utility is permanently stored on the BIOS chip on
the mainboard. It creates a record of the mainboard’s and some
system configuration information and stores it in battery-sup­ported memory on the mainboard. This record must be intact
and accurate in order for the mainboard to operate.

After a brief explanation of how to operate the utility there is
a summary of the entries and options for all sections of the util­ity. Under normal conditions, once your system is set up, you
should have little or no need to use this utility.

Using the CMOS Setup Utility

This mainboard uses the Award system BIOS. It is stored in a
Flash ROM memory chip on the mainboard. The BIOS uses a
software program, also stored on the same chip to create a sys­tem configuration record which is saved in a small amount of
special “CMOS” memory on the mainboard.

Accessing The CMOS Setup Utility

When you turn on your computer, a message appears on the
screen indicating you can run the Setup program by pressing the
Del key (it’s on the keypad.) The message appears after the POST
(Power On Self Test).

If you want to run Setup but you don’t respond in time before
the message disappears, you can reset the system by pressing the
Ctrl + Alt + Delete keys at the same time, or by pushing the
system Reset button. The message will then reappear.

After you press the Del or Delete key the program menu screen
will appear, displaying the Setup utility section names and some
command instructions.

P5TX–Bpro User’s Manual

4: Reference Information – 4.13

P5TX–Bpro User’s Manual

4: Reference Information – 4.14

Menu Commands

If you look at the lower portion of the screen illustration you’ll
see a section that lists the control commands for this level of the
program. You execute a command by pressing the key for that
command. The program commands are :

Quit

This command will close the Setup program when you press

the ESC key.
Save & Exit Setup

This will save the current settings and close the Setup pro-

gram when you press the F10 key.
Select Item

You can use the arrow keys on your keyboard to move around

the screen and select a menu item. An item is highlighted when

it is selected.
Change Color

Change the program color scheme by pressing Shift + F2.

The section at the bottom of the screen displays a brief expla­nation of a highlighted menu item’s function.

There are six main sections to the Setup program:

• Standard CMOS Setup

Date, time, disk drive, video display and error handling

• BIOS Features Setup

System customization features and video display settings

• Chipset Features Setup

Chipset settings, memory configuration feature for special-

ized add-on cards and VGA memory configuration

• Power Management Setup

Sets up the “green” power management features

• PNP/PCI Configuration

PCI expansion slot and system resource settings

P5TX–Bpro User’s Manual

4: Reference Information – 4.15

• Load BIOS Defaults

Loads minimum settings from the BIOS ROM.

• Load Optimum Settings

Loads optimized settings from the BIOS ROM.

• Integrated Peripherals

Settings for the IDE channels and onboard ports

• PC Health Monitor

Monitoring sensor settings and readings

The other main menu items interact with these main sections:

• Supervisor Password & User Password

Sets a system password which is configured by the Security

Option item in BIOS Features Setup.

• IDE HDD Auto Detection

Automatically detects the drive parameters of any installed

IDE hard disk drives and enters them automatically in the Stan-

dard CMOS Setup .

• Save & Exit Setup

Saves the current settings and exits the program.

• Exit Without Saving

Discards any changes made during the current session and

exits the program.

To enter a section of the Setup pr ogram, highlight the menu
item and press the Enter key.

P5TX–Bpro User’s Manual

4: Reference Information – 4.16

Note:

Due to a technical limitation
in producing the illustration of
this screen, the memory fig­ures shown are not standard.
Your system will display the
figures for the memory in­stalled on the mainboard.

Standard CMOS Setup

To enter this section, highlight this menu item in the main
menu and press the Enter key. The screen above will appear.

Menu Commands

If you look at the lower portion of the screen illustration you’ll
see a section that lists the control commands for this level of the
program. You execute a command by pressing the key for that
command. The program commands are :

Quit

This command will close the Setup program when you press

the ESC key.

Help

This displays information about the highlighted item when

you press the F10 key.

P5TX–Bpro User’s Manual

4: Reference Information – 4.17

Select Item

You can use the arrow keys on your keyboard to move around

the screen and select a menu item. An item is highlighted when

it is selected.

Change Color

You can change the program color scheme by pressing Shift +

F2.

Modify

T o change the setting of a highlighted selection you can press

either the Page Up (PU) and Page Down (PD) keys or the Plus

(+) and Minus (–) keys. Pressing a key once will switch to the

next setting option for the selected item.

If your mainboard is already installed in a working system the
proper entries are already entered on this screen and you shouldn’t
change them except for adjusting the Date and Time entries if
necessary.

Date & Time

The first two lines on the screen are the date and time settings
for the system clock.

Hard Disk Type & Parameters

Use the IDE HDD Auto Detection feature to automatically
enter the drive parameters of IDE hard disk drives in these fields.
If you have only SCSI hard disk drives installed in your system
leave the settings here at None. Only hard disk information needs
to be entered here. Other IDE devices do not use this.

For an IDE hard drive, you should set the entry to “Auto” and
the BIOS will automatically detect all drive information needed.
You can use the IDE HDD Auto Detection utility described later
to supervise the auto-detection process. If you want to do this,
leave the drive set to “None”. You can also enter specifications
manually by using the “User” option.

P5TX–Bpro User’s Manual

4: Reference Information – 4.18

Large Hard Disk Modes

The last of the drive parameter entries – Mode – has four op­tions, Normal, LBA, Large and Auto. The Mode settings are for
IDE hard disks only.

Normal

For IDE hard disks of 528MB or less.

LBA

This stands for Logical Block Addressing, the current standard

access mode for large IDE hard disk drives. It allows the use of

hard disks larger than 528MB by causing the IDE controller to

translate between the logical address it creates and the hard

disk’s actual physical address. The maximum drive size sup-

ported is 8.4GB.

Large

For 1GB or smaller drives with more than 1024 cylinders and

no LBA support. This access mode causes the Operating Sys-

tem to treat the drive as if it has fewer than 1024 cylinders by

dividing the cylinder total in half and doubling the number of

heads. Drives needing this mode are less common.

Most large IDE hard disk drives currently available use the
LBA mode. Use the AUTO setting to automatically detect the
correct mode for new drives.

Floppy Disk Drives

The two floppy disk drive items set the drive type for drives A
and B, and must be entered manually. The options are

360KB, 5.25 in.

1.2MB, 5.25 in.
720KB, 3.5 in.

1.44MB, 3.5 in.

2.88MB, 3.5 in.
None

P5TX–Bpro User’s Manual

4: Reference Information – 4.19

Highlight the listing after each drive name and select the ap­propriate entry.

Floppy 3 Mode Support

3 Mode is a Japanese 3.5-inch floppy disk drive specification.
If this type of drive is installed you should enable this feature.
The default setting is Disabled.

Video Display Types

You set this according to the type of display card in your sys­tem. This should normally be left on EGA/VGA. The options are:

EGA/VGA
Mono (for Hercules or MDA)
CGA 40
CGA 80

Error Handling

The last line – Halt On – sets when the system stops if an
error occurs. The options are:

All Errors (Default)
No Errors
All, But Keyboard
All, But Diskette
All, But Disk/Key

When you are finished in this section, exit to the main menu
screen by pressing the Esc key.

P5TX–Bpro User’s Manual

4: Reference Information – 4.20

BIOS Features Setup

T o enter this section of the Setup program, highlight this menu
item in the main menu and press the Enter key. The following
screen will appear.

P5TX–Bpro User’s Manual

4: Reference Information – 4.21

Menu Commands

If you look at the lower portion of the screen illustration you’ll
see a section that lists the control commands for this level of the
program. You execute a command by pressing the key for that
command. The program commands are :

Quit

This command will close the Setup program when you press

the ESC key.
Help

This displays information about the highlighted item when

you press the F10 key.
Select Item

You can use the arrow keys on your keyboard to move around

the screen and select a menu item. An item is highlighted when

it is selected.
Modify

T o change the setting of a highlighted selection you can press

either the Page Up (PU) and Page Down (PD) keys or the Plus

(+) and Minus (–) keys. Pressing a key once will switch to the

next setting option for the selected item.
Change Color

Change the program color scheme by pressing Shift + F2.
Old Values

If you make changes during the current session and you don’t

want to keep them you can recall the last set of saved values

for this page by pressing the F5 key.
Load BIOS Defaults

Pressing F6 loads the BIOS Default settings for this page.
Load Setup Defaults

Pressing F7 loads the Setup Default settings for this page.

If your mainboard is already installed in a working system the
proper entries are already entered on this screen and you shouldn’t
change them.

P5TX–Bpro User’s Manual

4: Reference Information – 4.22

Virus Warning

This protects the primary hard disk’s boot sector and partition
table from infection. Any attempt to write to them will halt the
system and produce a warning message. If this happens, you can
either allow the system to continue or stop it and boot from a
virus-free bootable floppy disk. Use an anti-virus utility located
on the floppy disk to check the hard disk. The default setting is
Disabled.

CPU Internal Cache

This enables CPU’s Level 1 built-in cache. Leave it enabled to
maintain system performance. The default setting is Enabled.

External Cache

This is the Level 2 external cache of either 256KB or 512KB.
Leave this enabled to maintain system performance. The default
setting is Enabled.

Quick Power On Self Test

This feature speeds up the Power On Self T est (POST) by skip­ping some parts of the POST. If your system is functioning nor­mally , you can enable this feature to speed the boot process. The
default setting is Enabled.

Boot Sequence

This determines the order in which the computer checks drives
for an operating system. In addition to the drive A: floppy disk
drive and the drive C: boot hard disk, you can configure the or­der to include another IDE hard disk drive or CD-ROM drive or
a SCSI device. The options are:

A, C, SCSI C, A, SCSI SCSI, A, C SCSI, C, A
D, A, SCSI E, A, SCSI F, A, SCSI
C, CD-ROM, A CD-ROM, C, A
C Only

P5TX–Bpro User’s Manual

4: Reference Information – 4.23

Swap Floppy Drive

This switches the floppy drive assignments so that drive A is
treated as drive B: and drive B: as drive A: under DOS. The de­fault setting is Disabled.

Boot Up NumLock Status

This item allows you to select which mode the numeric key­pad on an IBM-compatible extended keyboard is set to when the
computer boots up. The options are:

On – Numeric keypad mode (Default)
Off – Cursor control mode

Security Option

This sets when password protection is active. The two op­tions are:

System – Password required at boot up
Setup – Password controls access to Setup utility

You create a password using the Password Setting option in
the main menu. If no password is set, the system ignores this
item.

P5TX–Bpro User’s Manual

4: Reference Information – 4.24

PCI/VGA Palette Snoop

If your video display card has an MPEG card attached to the
feature connector, the display may invert to black on white while
booting. If this happens, set this line to Enabled to correct the
problem. The default setting is Disabled.

OS Select For DRAM >64MB

If your system has more than 64MB of system memory in­stalled and you are using the OS/2 operating system, set this to
the OS2 setting. The default setting, Non-OS2, is for all other
operating systems.

Video BIOS Shadow

This copies the video display card BIOS into system DRAM
to increase display speed and is required for system performance.
The default setting is Enabled.

Shadowing Address Ranges

The next six lines, from C8000-CBFFF Shadow to DC000­DFFFF Shadow are address ranges for shadowing other expan­sion card ROMs. If there are any expansion cards with ROMs
installed in your system, you have to know the address range
they use to shadow them specifically. The default setting for all
of these is Disabled.

When you are done in this section press the Esc key to return
to the main menu.

P5TX–Bpro User’s Manual

4: Reference Information – 4.25

Chipset Features Setup

T o enter this section of the Setup program, highlight this menu
item in the main menu and press the Enter key. The following
screen will appear.

Menu Commands

The menu commands for this screen are the same as for the
BIOS Features Setup screen.

Auto Configuration

Everything on this screen except for the Memory Hole item is
either an optimum setting or set automatically when auto-con­figuration is active. If you disable auto-configuration you can set
the DRAM timing values manually . We recommend against mak­ing any manual settings in this section unless you know what
you are doing. The default setting is Enabled.

P5TX–Bpro User’s Manual

4: Reference Information – 4.26

Memory Hole At 15M–16M

Some special add-on cards require a 1MB address space be­tween 15 and 16MB. The documentation for this type of card
should tell you if it needs this. The default setting is Disabled.

To retur n to the main menu press the Esc key.

P5TX–Bpro User’s Manual

4: Reference Information – 4.27

Power Management Setup

T o enter this section of the Setup program, highlight this menu
item in the main menu and press the Enter key. The following
screen will appear.

Menu Commands

The menu commands for this screen are the same as for the
BIOS Features Setup screen.

P5TX–Bpro User’s Manual

4: Reference Information – 4.28

What Power Management Does

Power management lets you set up your computer to save
electricity when it is not actively in use by putting the system
into progressively greater power saving modes. In the power man­agement scheme there are four system states which proceed in
the following sequence:

Normal
Doze
Standby
Suspend

Power Management

This controls the entire power management scheme. There
are four settings:

User Defined

You set the power saving options manually
Disable

Turns of f all power management
Max Saving

Maximizes power saving by activating maximum power sav-

ing settings after one minute of system inactivity
Min Saving

Produces less power saving by activating moderate power sav-

ing settings after one hour of system inactivity

PM Control By APM

When this is set to Yes the Advanced Power Management fea­ture in Microsoft Windows controls power management opera­tion. The default setting is No.

P5TX–Bpro User’s Manual

4: Reference Information – 4.29

Video Off Method

This governs monitor power saving by controlling how power
management blanks the monitor screen. The default setting blanks
the screen and turns off vertical and horizontal scanning and re­quires a monitor with “green” features. If you don’t have this
type of monitor, use the Blank option. DPMS (Display Power
Management System) allows the BIOS to control the video dis­play card if the card has the DPMS feature.

V/H SYNC+Blank (Default)
Blank (Non-green monitor, less saving)
DPMS (Display card must support DPMS)

Video Off After

This governs when the video display gets turned off. The op­tions are:

Suspend Off after system enters Suspend mode
Standby Off after system enters Standby mode
Doze Off after system enters Doze mode
N/A No display shut off

P5TX–Bpro User’s Manual

4: Reference Information – 4.30

Doze Mode

This sets the period of system inactivity after which the sys­tem goes into Doze mode, the most limited power saving state.
The settings range from 1 minute to 1 hour and can be set manu­ally when power management is in User Define mode. The de­fault setting is Disabled. When the system goes into power sav­ing mode, power management will skip to the next mode in the
sequence if this is disabled.

Standby Mode

This sets the period of system inactivity after which the sys­tem goes into Standby mode, the intermediate power saving state.
The settings range from 1 minute to 1 hour and can be set manu­ally when power management is in User Define mode. The de­fault setting is Disabled. When the system goes into power sav­ing mode, power management will skip to the next mode in the
sequence if this is disabled.

Suspend Mode

This sets the period of system inactivity after which the sys­tem goes into Suspend mode, the maximum power saving state.
The settings range from 1 minute to 1 hour and can be set manu­ally when power management is in User Define mode. The de­fault setting is Disabled. When the system goes into power sav­ing mode, power management will skip to the next mode in the
sequence if this is disabled.

HDD Power Down

This shuts down IDE hard disks that support a power saving
mode after a specified time period. The settings range from 1 to
15 minutes and can be set manually when power management is
in User Define mode. HDD Power Down does not affect SCSI
hard disks. The default setting is Disabled.

P5TX–Bpro User’s Manual

4: Reference Information – 4.31

The system automatically resumes from any power saving
mode when there is system activity such as keyboard activity or
an IRQ wake-up event like mouse movement or a modem ring.

Throttle Duty Cycle

This line sets the percentage by which the CPU speed is cut
back when power saving initiates. The settings are:

62.5% Default
75%

87.5%

12.5%
25%

37.5%
50%

ZZ Active In Suspend

This item puts the cache controller into sleep mode when the
system is in Suspend mode to achieve additional power saving.
The default setting is Disabled, the option is Enabled.

VGA Active Monitor

When this line is set to the default, Enabled, the system will
not initiate power saving while there is display activity . The other
option is Disabled.

P5TX–Bpro User’s Manual

4: Reference Information – 4.32

CPU Fan Off In Suspend

In the default Enabled setting, when a CPU Fan is connected
to one of the fan power connectors on the mainboard, the fan
will turn off when the system is in Suspend mode. The other
option is Disabled.

Break Event From Suspend

The two lines in this section control whether the system will
wake-up if either of the events noted occur. The defaults are
shown on the screen illustration.

Reload Global Timer Events

The system will restart the power saving count-down when
an event generates from any of the items in this section that are
set to Enabled.

When you are finished in this section, press the Esc key to
return to the main menu.

P5TX–Bpro User’s Manual

4: Reference Information – 4.33

PNP/PCI Configuration

T o enter this section of the Setup program, highlight this menu
item in the main menu and press the Enter key. The following
screen will appear.

Menu Commands

The menu commands for this screen are the same as for the
BIOS Features Setup screen.

P5TX–Bpro User’s Manual

4: Reference Information – 4.34

Resources Controlled By

When this line is set to Auto the BIOS will automatically con­figure IRQ and DMA resources. This is the recommended set­ting. If you set this line to Manual, the screen changes as shown
above and allows manual configuration. In general you should
only need to do this if you are installing an ISA card that requires
manual configuration.

Reset Configuration Data

The default setting is ‘Disabled’. If you need to clear the ESCD
data, set this to ‘Enabled’. The data will clear automatically and
the BIOS will reset this line to the ‘Disabled’ setting.

P5TX–Bpro User’s Manual

4: Reference Information – 4.35

PCI IDE IRQ Map To

Most of PCI IDE cards are non-PCI compliant. This line de­fines the IRQ Routing to make them work properly. The avail­able settings are:

PCI-AUTO (default)
ISA
PCI-SLOT1
PCI-SLOT2
PCI-SLOT3
PCI-SLOT4

If you set this option to ‘ISA’, both the ‘Primary IDE INT#’
and ‘Secondary IDE INT#’ options below it will not appear on
the screen.

Primary/Secondary IDE INT#

These define the primary/secondary IDE INT# of a PCI IDE
card. The setting options are:

A (Primary IDE INT# default )
B (Secondary IDE INT# default )
C
D

When you are finished you can press the Esc key to return to
the main menu.

P5TX–Bpro User’s Manual

4: Reference Information – 4.36

Load BIOS Defaults

T o use this command highlight it in the main menu and press
Enter. A message will appear asking if you want to load the BIOS
Defaults. Press the Y key and then the Enter key. The BIOS de­fault settings will load. Press the N key if you want to cancel.

This loads a set of troubleshooting default values permanently
stored in the BIOS ROM. The settings are not optimal and turn
off all the performance features. Standard CMOS Setup is not
affected by this command.

Load Optimized Settings

T o use this command highlight it in the main menu and press
Enter. A message will appear asking if you want to load the Op­timized Settings. Press the Y key and then the Enter key. The
optimized default settings will load. Press the N key if you want
to cancel.

This loads a set of optimized default values permanently stored
in the BIOS ROM. Use this command to load default settings for
normal system operation. Standard CMOS Setup is not affected
by this command.

P5TX–Bpro User’s Manual

4: Reference Information – 4.37

Integrated Peripherals

This section sets the IDE transfer mode for all IDE channels. It
also configures the other onboard ports.

Menu Commands

The menu commands for this screen are the same as for the
BIOS Features Setup screen.

P5TX–Bpro User’s Manual

4: Reference Information – 4.38

IDE HDD Block Mode

Enables hard disk drive block transfer mode . The setting op­tions are:

Enabled (default)
Disabled

On-Chip Primary/Secondary PCI IDE

Enables or Disables the Primary or Secondary PCI controllers.
Selecting “Disabled”

Enabled (default)
Disabled

releases IRQ14.

IDE Primary/Secondary Master/ Slave PIO

These four lines set the hard disk PIO transfer mode, which
affects the hard disk data transfer rate. The system will auto­detect the PIO mode of a device in any of these positions when
they are set to ‘Auto’, the recommended setting. Alternatively,
you can set the mode manually. Modes 0 to 4 are supported.

Primary/Master Master/Slave UltraDMA

These four lines enable hard disk UltraDMA transfer mode,
which requires a drive that supports this data transfer method.
The system will auto-detect an UltraDMA device in any of these
four positions when they are set to ‘Auto’, the recommended
setting. The other setting is ‘Disabled’. You can leave these set to
Auto without effect if there are no UltraDMA devices installed.

USB Keyboard Support

Enables or Disables support for a USB keyboard. Enable this if
you connect a USB keyboard. The default is Disabled.

P5TX–Bpro User’s Manual

4: Reference Information – 4.39

Onboard FDD Controller

Enables or Disables the onboard Floppy Drive controller.

Onboard Serial Port 1/2

Sets the I/O address for serial ports 1 & 2.

3F8/IRQ4 Onboard serial port COM1 default
2F8/IRQ3 Onboard serial port COM2 default
3E8/IRQ4
2E8/IRQ3
Disabled

UART 2 Mode

Sets mode for the second serial port UART . If you select an IR
module type, the second serial port will not be available. Setting
options for the selected IR option appear when you select an IR
type. The setting options are:

Standard (default) – (used by COM2 serial port)
ASKIR
HPSIR

Onboard Parallel Port

Sets the I/O address for the onboard parallel port. The setting
options are:

378H/IRQ7 (default)
Disabled
278H/IRQ5
3BCH/IRQ7

P5TX–Bpro User’s Manual

4: Reference Information – 4.40

If you set this to ‘Disabled’, the
tion below will not appear on the screen.

‘Onboard Parallel Mode’

op-

Onboard Parallel Mode

Selects the parallel port mode. The setting options are:

SPP (default)
ECP/EPP
EPP/SPP
ECP

If you set this option to ‘SPP’ or ‘EPP/SPP’, the ‘ECP Mode
Use DMA’ option will not appear on the screen. If you set this
option to ‘SPP’ or ‘ECP’, the ‘Parallel Port EPP Type’ option will
not appear on the screen.

ECP Mode Use DMA

Selects the ECP Mode DMA channel. The setting options are:

3 (default)
1

Parallel Port EPP Type

Sets the EPP protocol version. The setting options are:

EPP 1.7 (default)
EPP 1.9

P5TX–Bpro User’s Manual

4: Reference Information – 4.41

PC Health Monitor

T o enter this section of the Setup program, highlight this menu
item in the main menu and press the Enter key.

Menu Commands

The menu commands for this screen are the same as for the
BIOS Features Setup screen.

What The Health Monitor Does

This section of the CMOS Setup utility is connected to the
sensor technology on the mainboard. The sensor monitors the
voltage and temperature status for the items listed on this screen.

There are two sections on this screen, Warning Messages and
PC Status. The Warning Messages section has settings that con­trol the monitoring function. The PC Status section displays the
current status of the listed items as detected by the onboard sen­sor, including voltage readings and temperatures.

Warning Messages

This section of the screen lists the items monitored by the
sensor and enables warning messages which appear during the
POST (Power On Self Test), which runs when your computer is
starting up. If the sensor detects a condition outside safe param­eters during start-up, it will generate a warning message.

You can set the expected core voltage for the CPU under CPU
Voltage. The options for the rest of the items listed are Enabled
and Disabled.

P5TX–Bpro User’s Manual

4: Reference Information – 4.42

The monitored items and default settings are:

**** Warning Messages ****
+12V Voltage Enabled
–12V Voltage Enabled
+5V Voltage Enabled
+3.3V Voltage Enabled
CPU Voltage 2.8V

(2.93V; 3.2V; 3.3V; Disabled)
CPU Fan Disabled
CPU Temperature Enabled
Mainboard Temperature Enabled
Chassis Enabled

PC Status

When you call up the PC Health Monitor screen this section
displays the current readings from the onboard sensor. The read­ings are for the same items as in the Warning Message list.

The last line, System Status indicates the current evaluation of
the system state in terms of the monitored items listed. Under
normal conditions it will display ‘OK!’ as the system status. If
there is a problem a warning will appear.

P5TX–Bpro User’s Manual

4: Reference Information – 4.43

Password Setting

T o use this command, highlight it in the main menu and press
Enter. A message will appear prompting you to enter a password.

Type in a passwor d. The password is case sensitive, and can
be up to 8 alphanumeric characters. Press Enter when you finish
typing in the password.

If you typed in a password, the message “Confirm Password”
will appear. Confirm the password by typing it again and press­ing Enter. The message box will close.

If you decide you don’t want to set a password after you acti­vate this command, or if you want to eliminate an existing pass­word, press Enter without typing anything else. The message
“Password Disabled” will appear and the message box will close.

When you set a password, the Security Option line in BIOS
Features Setup controls when the password is required. You can
set the option to require the password when the system boots up
or when calling up the CMOS Setup utility . The mainboard ships
with no password.

IDE HDD Auto Detection

When you install an IDE hard drive, you can use this feature
to automatically detect the drive parameters and enter them in
the appropriate Hard Disk section of Standard CMOS Setup.
However, since the Auto settings in Standard CMOS Setup per­form the same function, you do not need to configure IDE hard
disk drives from here. If you want to use this feature, highlight it
in the main menu and press the Enter key.

P5TX–Bpro User’s Manual

4: Reference Information – 4.44

Save And Exit Setup

When you select this and press Enter the values entered dur­ing the current session are recorded in CMOS memory.

Exit Without Saving

When you select this and press Enter the Setup Utility closes

without recording any changes made during the current session.