ECS B85H3-M7, H81H3-M7 User Manual

B85H3-M7 USER MANUAL

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.

Other product names used in this manual are the properties of their respective owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

B85H3-M7 USER MANUAL

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

The manual consists of the following:

Describes features of the motherboard.

page 1

Describes installation of motherboard components.

page 7

page 27

page 63

Installing the Motherboard

Introducing the Motherboard

Provides information on using the BIOS Setup Utility.

Describes the motherboard software.

Limits and methods of mesurement of radio disturbance characteristics of information technology equipment

EN 55022

EN 61000-3-2

Disturbances in supply systems caused

EN 61000-3-3

Disturbances in supply systems caused by household appliances and similar electrical equipment “ Voltage fluctuations”

EN 55024

Information technology equipment-Immunity characteristicsLimits and methods of measurement

EN 60950

Safety for information technology equipment including electrical business equipment

CE marking

About the Manual



This device is in conformity with the following EC/EMC directives:

Chapter 4

Chapter 1

Chapter 2

Chapter 3 Using BIOS

Using the Motherboard Software

Chapter 5 Trouble Shooting

Provides basic trouble shooting tips.

page 67

iii

B85H3-M7 USER MANUAL

Chapter 2 7

Installing the Motherboard 7

Safety Precautions..............................................................................7

Installing the Motherboard in a Chassis.......................................7

Checking Jumper Settings..................................................................8

Installing Hardware...........................................................................9

Installing the Processor............................................................9

Installing the CPU Cooler........................................................11

Installing Memory Modules...................................................12

Installing Add-on Cards..........................................................13

Connecting Optional Devices.................................................15

Installing a SATA Hard Drive...................................................22

Connecting Case Components........................................................23

Front Panel Header................................................................25

TABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...........................................................................................1

Pakage Contents..................................................................................1

Specifications......................................................................................2

Motherboard Components................................................................4

I/O Ports...............................................................................................6

Chapter 3 27

Using BIOS 27

About the Setup Utility......................................................................27

The Standard Configuration........................ ...........................27

Entering the Setup Utility.......................................................27

Resetting the Default CMOS Values.....................................28

Using BIOS.........................................................................................28

BIOS Navigation Keys..............................................................29

Main Menu.............................................................................30

Advanced Menu......................................................................31

Chipset Menu..........................................................................46

M.I.B III(MB Intelligent Bios III) Menu....................................49

Boot Menu...............................................................................58

Security Menu.........................................................................59

Exit Menu................................................................................60

Updating the BIOS......................................................................61

B85H3-M7 USER MANUAL

Chapter 4 63

Using the Motherboard Software 63

Auto-installing under Windows XP/7/8.......................................63

Running Setup........................................................................63

Manual Installation..........................................................................65

ECS Utility Software (Intelligent EZ Utility).....................................65

Chapter 5 67

Trouble Shooting 67

Start up problems during assembly..............................................67

Start up problems after prolong use............................................68

Maintenance and care tips..............................................................68

Basic Troubleshooting Flowchart.....................................................69

B85H3-M7 USER MANUAL

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the B85H3-M7 motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1150 socket for Intel® Haswell Processor.

This motherboard is based on Intel® B85 Express Chipset for best desktop platform solution. It supports up to 16 GB of system memory with dual channel long DDR3 1600/1333 MHz. One PCI Express x16 slot, intended for Graphics Interface, is fully conformed to PCI Express 3.0 Standard. In addition, two PCI Express x1 slots are for extending usage.

It integrates USB 2.0 and USB 3.0 interface, supporting up to eight USB 2.0 ports (four USB 2.0 ports and two USB 2.0 headers support additional four USB 2.0 ports) and four USB 3.0 ports (two USB 3.0 ports at the rear panel and one USB 3.0 header supports additional two USB 3.0 ports).

The motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and PS/2 keyboard connectors, one VGA port, one DVI port, one HDMI port, four USB 2.0 ports, two USB 3.0 ports, one RJ45 LAN connector, and audio jacks for microphone, line-in and 6-ch line-out.

In addition, this motherboard supports two SATA 6Gb/s and two SATA 3Gb/s connectors for expansion.

Your motherboard package ships with the following items:

Package Contents

B85H3-M7 Motherboard Quick Installation Guide User Manual DVD I/O Shield 2 SATA Cables

     

The package contents above are for reference only, please take the actual package items as standard.

Chapter 1

B85H3-M7 USER MANUAL

CPU

Specifications

• Intel® B85 Express Chipset

Chipset

• Dual-channel long DDR3 memory architecture

• 2 x 240-pin DDR3 DIMM sockets support up to 16 GB

• Supports DDR3 1600/1333 MHz DDR3 SDRAM

Memory

• 1 x PCI Express x16 Gen3 slot

• 2 x PCI Express x1 slots

• Supported by Intel® B85 Express Chipset

- 2 x Serial ATA 3Gb/s devices

- 2 x Serial ATA 6Gb/s devices

Expansion Slots

Storage

• 1 x PS/2 keyboard and PS/2 mouse connectors

• 1 x VGA port

• 1 x DVI port

• 1 x HDMI port

• 4 x USB 2.0 ports

• 2 x USB 3.0 ports

• 1 x RJ45 LAN connector

• 1 x Audio port (1x Line in, 1x Line out, 1x Mic_in Rear)

Rear Panel I/O

LAN • Realtek 8111G Gigabit LAN (co-lay 8106)

• LGA1150 socket for Intel® Haswell Processor

Note: Please go to ECS website for the latest CPU support list.

Note: Please go to ECS website for the latest Memory support list.

• 1 x 24-pin ATX Power Supply connector

• 1 x 4-pin ATX12V Power connector

• 1 x 4-pin CPU_FAN connector

• 1 x 3-pin SYS_FAN connector (co-lay 4-pin)

• 2 x USB 2.0 headers support additional four USB 2.0 ports

• 1 x USB 3.0 header supports additional two USB 3.0 ports

• 2 x SATA 3Gb/s connectors

• 2 x SATA 6Gb/s connectors

• 1 x COM header

• 1 x Case open header

• 1 x CLR_CMOS header

• 1 x Front Panel audio header

• 1 x Front Panel switch/LED header

• 1 x SPDIFO header

• 1 x LDC header

• 1 x SPK header

Internal I/O Connectors & Headers

• Realtek ALC662

- 6 Channel High Definiton Audio Codec

- Compliant with HD audio specification

Audio

• 1 x LPT header

B85H3-M7 USER MANUAL

Chapter 1

• AMI BIOS with 64Mb SPI Flash ROM

• Supports Plug and Play, STR(S3)/STD(S4)

• Supports Hardware Monitor

• Supports ACPI & DMI

• Audio, LAN, can be disabled in BIOS

• Supports Dual/Triple Display (depends on display output)

• F7 hot key for boot up devices option

• Supports Pgup clear CMOS Hotkey (Has PS2 KB Model only)

• Supports Multi-Language

• Supports AC’97/HD Audio auto detect (default)

System BIOS

Form Factor

• Micro-ATX Size, 225mm x 180mm

Chapter 1

B85H3-M7 USER MANUAL

Motherboard Components

B85H3-M7 USER MANUAL

Chapter 1

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket LGA1150 socket

2. SYS_FAN 3-pin system cooling fan connector (co-lay 4-pin)

3. CPU_FAN 4-pin CPU cooling fan connector

4. DDR3_1~2 240-pin long DDR3 Module slots

5. ATX_POWER Standard 24-pin ATX power connector

6. SATA2_3~4 Serial ATA 3.0 Gb/s connectors

7. CASE CASE open header

8. F_PANEL Front panel switch/LED header

9. SPK Speaker header

10. SATA3_1~2 Serial ATA 6.0 Gb/s connectors

11. F_USB1~2 Front panel USB 2.0 headers

12. LDC Debug card header

13. COM Onboard serial port header

14. LPT Printer Header

15. F_AUDIO Front panel audio header

16.SPDIFO SPDIF out header

17. PCIE1~2 PCI Express x1 slots

18. CLR_CMOS Clear CMOS jumper

19. PCIEX16 PCI Express slot for graphics interface

20. USB3F Front panel USB 3.0 header

21. ATX12V 4-pin +12V power connector

Chapter 1

B85H3-M7 USER MANUAL

I/O Ports

1. PS/2 Mouse (green)

Use this PS/2 port to connect a PS/2 mouse.

2. PS/2 Keyboard (purple) Use this PS/2 port to connect a PS/2 keyboard.

3. VGA Port

Connect your monitor to the VGA port.

4. DVI Port

You can connect the display device to the DVI port.

5. HDMI Port

You can connect the display device to the HDMI port.

6. USB 2.0 Ports

Use the USB 2.0 ports to connect USB 2.0 devices.

7. USB 3.0 Ports

Use the USB 3.0 ports to connect USB 3.0 devices.

8. LAN Port

Connect an RJ-45 jack to the LAN port to connect your computer to the Network.

9. Line-in (blue) It can be connected to an external CD/DVD player, Tape player or other audio devices for audio input.

10. Line-out (lime) It is used to connect to speakers or headphones.

11. Microphone (pink) It is used to connect to a microphone.

LAN LED Status Description

OFF No d ata Orange blinking Active OFF No link Green Link

Activity LED

Link LED

LAN Port

Chapter 2

B85H3-M7 USER MANUAL

Chapter 2

Installing the Motherboard

2-1. Safety Precautions

2-2. Installing the motherboard in a Chassis

This motherboard carries a Micro ATX form factor of 225 x 180 mm. Choose a chassis that accommodates this from factor. Make sure that the I/O template in the chassis matches the I/O ports installed on the rear edge of the motherboard. Most system chassis have mounting brackets installed in the chassis, which corresponds to the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Follow these safety precautions when installing the motherboard:

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity.

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard.

• Leave components in the static-proof bags.

• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

Do not over-tighten the screws as this can stress the motherboard.

Chapter 2

B85H3-M7 USER MANUAL

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

1. To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.

2-3. Checking Jumper Settings

Chapter 2

B85H3-M7 USER MANUAL

2-4. Installing Hardware

2-4-1. Installing the Processor

• This motherboard has an LGA1150 socket.

• When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

• You may be able to change the settings in the system Setup Utility. We strongly recommend you do not over-clock processor or other components to run faster than their rated speed.

• The following illustration shows CPU installation components.

A. Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab.

B. Lift the tail of the load lever and rotate the load plate to fully open position.

C. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.

Chapter 2

B85H3-M7 USER MANUAL

D. Rotate the load plate onto the package IHS (Intergraded Heat Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically.

Please save and replace the cover onto the CPU socket if processor is removed.

Chapter 2

B85H3-M7 USER MANUAL

A. Apply some thermal grease onto the contacted area between the heatsink and the CPU, and make it to be a thin layer.

B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector.

C. Connect the CPU cooler power connector to the CPU_FAN connector.

2-4-2. Installing the CPU Cooler

• Install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

• Avoid using cooling fans with sharp edges in case the fan casing and the clips cause serious damage to the motherboard or its components.

• To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heat sink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.

• DO NOT remove the CPU cap from the socket before installing a CPU.

• Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1150 socket.

• The following illustration shows how to install CPU fan.

Chapter 2

B85H3-M7 USER MANUAL

2-4-3. Installing Memory Modules

• This motherboard accommodates two memory modules. It can support two 240-pin DDR3 1600/1333.

• Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

• You must install at least one module in any of the two slots. Total memory capacity is 16 GB.

• Refer to the following to install the memory modules.

C. The slot latches are levered upwards and latch on to the edges of the

DIMM.

A. Push the latches on each side of the DIMM slot down.

B. Install the DIMM module into the slot and press it firmly down until it

seats correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot.

Chapter 2

B85H3-M7 USER MANUAL

2-4-4. Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

PCIEX16 Slot

The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revision 3.0.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

The PCI Express x1 slots are fully compliant to the PCI Express Base Specification revision 2.0.

PCIE1~2 Slots

Chapter 2

B85H3-M7 USER MANUAL

Install the VGA Card in the PCIE X16 slot

1 Remove a blanking plate from the system case corresponding to the slot

you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

1. For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

2. The onboard PCI interface does not support 64-bit SCSI cards.

Follow these instructions to install an add-on card:

Please refer the following illustrations to install the add-on card:

Install the LAN Card in the PCIE X1 slotInstall the VGA Card in the PCI slot

Chapter 2

B85H3-M7 USER MANUAL

2-4-5. Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

No. Components No. Components

1 SATA2_3/4 & SATA3_1/2 6 L PT

2 CASE 7 SPDIFO

3F_USB1~28F_AUDIO

4LDC9USB3F

5COM~ ~

Chapter 2

B85H3-M7 USER MANUAL

SATA2_3/4 connectors are used to support the Serial ATA 3.0Gb/s devices, and SATA3_1/ 2 connectors support the Serial ATA 6.0Gb/s device, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

1. SATA2_3/4 & SATA3_1/2 : Serial ATA connectors

2. CASE: Chassis Intrusion Detect Header

This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.

Chapter 2

B85H3-M7 USER MANUAL

The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

3. F_USB1~2: Front Panel USB 2.0 headers

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hangup.

4. LDC: Debug Card Header

Chapter 2

B85H3-M7 USER MANUAL

5. COM: Onboard serial port header

Connect a serial port extension bracket to this header to add a serial port to your system.

6. LPT: Onboard parallel port Header

This is a header that can be used to connect to the printer, scanner or other devices.

Chapter 2

B85H3-M7 USER MANUAL

This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.

7. SPDIFO: SPDIF out header

The front panel audio header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC’ 97 front panel audio to HD onboard headers, please set as below picture.

8. F_AUDIO: Front Panel Audio Header

Chapter 2

B85H3-M7 USER MANUAL

If you use AC’ 97 Front Panel, please tick off the option of “Disabled Front Panel Detect ”. If you use HD Audio Front Panel, please don’ t tick off “Disabled Front Panel Detect

” .

* For reference only

AC’ 97 Audio Configuration: To enable the front panel audio connector to support AC97 Audio mode.

If you use AC’ 97 Front Panel, please don’ t tick off “ Using Front Jack Detect ” . If you use HD Audio Front Panel, please tick off the option of “Using Front Jack Detect ”.

* For reference only

Chapter 2

B85H3-M7 USER MANUAL

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hangup.

This Motherboard implements one USB 3.0 header supporting 2 extra front USB 3.0 ports, which delivers 5Gb/s transfer rate.

9. USB3F: Front Panel USB 3.0 header

Chapter 2

B85H3-M7 USER MANUAL

2-4-6. Installing a SATA Hard Drive

About SATA Connectors

Your motherboard features four SATA connectors supporting a total of four drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with a SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

* For reference only

Installing Serial ATA Hard Drives

This section describes how to install a SATA Hard Drive.

Chapter 2

B85H3-M7 USER MANUAL

1 & 2. CPU_FAN(CPU cooling FAN Power Connector) & SYS_FAN (co-lay 4 pin)(System Cooling FAN Power Connector)

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V.

2-4-7. Connecting Case Components

No. Components No. Components

1 SYS_FAN 4 F_P ANEL

2 CPU_FAN 5 SPK

3 ATX_POWER 6 ATX12V

Connect the CPU cooling fan cable to CPU_FAN

Connect the system cooling fan connector to SYS_FAN.

Chapter 2

B85H3-M7 USER MANUAL

3 & 6. ATX_POWER (ATX 24-pin Power Connector) & ATX12V (ATX 12V Power Connector)

The ATX 24-pin connector allows you to connect to ATX v2.x power supply.

With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX match perfectly.

Connecting 24-pin power cable

24-pin power cable

Connect the standard power supply connector to ATX_POWER. Connect the auxiliary case power supply connector to ATX12V.

The ATX12V4P power connector is used to provide power to the CPU.

When installing 4-pin power cable, the latches of power cable and the ATX12V4P match perfectly.

Connecting 4-pin power cable

4-pin power cable

Chapter 2

B85H3-M7 USER MANUAL

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

4. Front Panel Header

The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:

Chapter 2

B85H3-M7 USER MANUAL

5. SPK: Speaker

Connect the case speaker cable to SPK.

This concludes Chapter 2. The next chapter covers the BIOS.

B85H3-M7 USER MANUAL

Chapter 3

About the Setup Utility

The computer uses the latest “American Megatrends Inc.” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Press DEL to enter SETUP

Chapter 3

Using BIOS

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

B85H3-M7 USER MANUAL

Chapter 3

Press the delete key to access BIOS Setup Utility.

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with an icon

) lead to submenus that enable you to change

the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.

Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.

Choose the system default language

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

BIOS Information

System Language English

System Date

Tue 07/03/2013

System Time 00:05:46

B85H3-M7 USER MANUAL

Chapter 3

The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by an icon

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

Scrolls through the items on a menu

+/- Change Opt.

F2 Previous Value

F3 Optimized Defaults

F1 General Help

ESC Exits the current menu



Enter Select

F4 Save & Exit

1. For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.

2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select item; Double click: enter; Right click: exit.

B85H3-M7 USER MANUAL

Chapter 3

System Date & Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.

System Language (English)

This item is used to set system language.

When you enter the BIOS Setup program, the main menu appears, giving you an overview of the basic system information. Select an item and press <Enter> to display the submenu.

Main Menu

F4: Save & Exit ESC/Right Click: Exit

Choose the system default language

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

BIOS Information

System Language English

System Date

Tue 07/23/2013

System Time 00:05:46

B85H3-M7 USER MANUAL

Chapter 3

The Advanced menu items allow you to change the settings for the CPU and other system.

Advanced Menu

LAN Configuration

The item in the menu shows the LAN-related information that the BIOS automatically detects.

Onboard LAN Controller (Enabled)

Use this item to enable or disable Onboard LAN controller.

Press <Esc> to return to the Advanced Menu page.

LAN Configuration Parameters

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

LAN Configuration

PC Health Status Power Management Setup PCI Express Configuration ACPI Settings CPU Configuration SATA Configuration

Intel(R) Rapid Start Technology Intel(R) Smart Connect Technology Intel ME BIOS Extension Configuration

Enabled/Disabled Onboard LAN Controller

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

LAN Configuration

Onboard LAN Controller Enabled

USB Configuration Super IO Configuration

B85H3-M7 USER MANUAL

Chapter 3

PC Health Status

On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.

Scroll to this item and press <Enter> to view the following screen:

Smart Fan Function

CPU/System Smart Fan Control (Enabled)

This item allows you to enable/disable the control of the CPU/System fan speed by changing the fan voltage.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU Smart Fan Control Enabled

Smart Fan Mode Normal

Smart Fan start PWM value 180 Smart Fan start PWM TEMP(DTS) 45 DeltaT +3 Smart Fan Slope PWM value 10 PWM value/unite CPU Fan Full Speed Offset (DTS) 52

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU Temperature (DTS) : 45 System Temperature : 32

C CPU Fan Speed : 3126 RPM System Fan Speed : 0 RPM Processor Input Voltage : 1.740V DIMM Voltage : 1.488V

TCC Activation Temperature (DTS) 75

Smart Fan Function

PC Health Status

Smart Fan start PWM value 180 Smart Fan start PWM TEMP(DTS) 45 DeltaT +3 Smart Fan Slope PWM value 10 PWM value/unite System Fan Full Speed Offset (DTS) 52

System Smart Fan Control Enabled Smart Fan Mode Normal

Enable CPU SmartFan

B85H3-M7 USER MANUAL

Chapter 3

System Component Characteristics

These items display the monitoring of the overall inboard hardware health events, such as CPU fan speed, DIMM voltage... etc.

Press <Esc> to return to the Advanced Menu page.

Smart Fan Mode (Normal)

This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quiet mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjusted depending on users’ parameters.

Press <Esc> to return to the PC Health Status page.

Smart Fan Start PWM value (180)

Smart Fan Start TEMP(DTS) (45)

This item is used to set the start PWM value of the smart fan.

This item is used to set the start temperature of the smart fan.

DeltaT (+3)

This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.

Smart Fan Slope PWM value (10 PWM value/unite)

This item is used to set the Slope Select PWM of the smart fan.

This item is used to set the CPU/System fan full speed offset value.

CPU/System Fan Full Speed Offset(DTS) (52)

• CPU Temperature (DTS)

• System Temperature

• CPU Fan Speed

• System Fan Speed

• Processor Input Voltage

• DIMM Voltage

B85H3-M7 USER MANUAL

Chapter 3

EUP Function (Enabled)

This item allows user to enable or disable EUP function.

Resume By PS2 MS (Disabled)

This item enables or disables you to allow mouse activity to awaken the system from power saving mode.

Power Management Setup

This page sets up some parameters for system power management operation.

Resume By PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card.

Resume By USB (Disabled)

This item allows you to enable/disable the USB device wakeup function from S3 mode.

Resume By RING (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature.

Resume By PS2 KB (Disabled)

This item enables or disables you to allow keyboard activity to awaken the system from power saving mode.

Power LED Type (Dual Color LED)

This item shows the type of the power LED.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

About Resume by Ring

Power Management Setup

Resume By RING Disabled

Resume By PME Disabled Resume By USB Disabled Resume By PS2 KB Disabled Resume By PS2 MS Disabled Resume By RTC Alarm Disabled EUP Function Enabled Power LED Type Dual Color LED

Resume By RTC Alarm (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wakeup alarm. You must use an ATX power supply in order to use this feature.

B85H3-M7 USER MANUAL

Chapter 3

PCI Express Configuration

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Configure PCI Express 16X speed B0: D1:F0 Gen 1- Gen 3

NB PCI Express Configuration

PCI Express 16X

PCI Express 16X Speed Auto

PCI Express Configuration

PCI E 1 PCIe Speed Auto

The item in the menu shows the information of PCI Express Configuration.

This item allows user to configure the PCI Express 16X/ PCIE1/ PCIE2 speed.

PCI Express 16X/ PCIE1/ PCIE2 Speed (Auto)

PCI E 2 PCIe Speed Auto

B85H3-M7 USER MANUAL

Chapter 3

ACPI Setting

The item in the menu shows the highest ACPI sleep state when the system enters suspend.

ACPI Sleep State (S3(Suspend to RAM))

This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).

Press <Esc> to return to the Advanced Menu page.

CPU Configuration

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

ACPI Settings

ACPI Sleep State S3 (Suspend to RAM)

Select the highest ACPI sleep state the system will enter when the suspend button is pressed.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enabled for Windows XP and Linux (OS optimized for HyperThreading Technology) and Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled only one thread per enabled core is enabled.

CPU Configuration

Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz EM64T Supported Processor Speed 2000 MHz Processor Stepping 306c3 Microcode Revision 12 Processor Cores 4 Intel HT Technology Supported Intel VT-x Technology Supported

Hyper-threading Enabled

Active Processor Cores All Limit CPUID Maximum Disabled Execute Disable Bit Enabled Intel Virtualization Technology Enabled LakeTiny Feature Enabled CPU C3 Report Enabled CPU C6 Report Disabled CPU C7 Report Disabled Package C State limit Auto Enhanced Halt (C1E)

Enabled

B85H3-M7 USER MANUAL

Chapter 3

Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz

This is display-only field and diaplays the information of the CPU installed in your computer.

EM64T (Supported)

This item shows the computer supports EMT64.

Processor Speed (2000MHz)

This item shows the current processor speed.

Processor Stepping (306c3)

This item shows the processor stepping version.

Microcode Revision (12)

This item shows the Microcode version.

Processor Cores (4)

This item shows the core number of the processor.

Execute Disable Bit (Enabled)

This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.

Intel Virtualization Technology (Enabled)

When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.

Limit CPUID Maximum

(Disabled)

Use this item to enable or disable the maximum CPUID value limit.

Intel HT Technology (Supported)

This item shows that your computer supports Intel HT technology or not.

Intel VT-x Technology (Supported)

This item shows that your computer supports Intel VT-x technology or not.

CPU C3 Report (Enabled)

Use this item to enable or disable CPU C3(ACPI C2) report to OS.

CPU C6 Report (Disabled)

Use this item to enable or disable CPU C6(ACPI C3) report to OS.

Active Processor Cores (All)

Use this item to control the active processor cores.

LakeTiny Feature (Enabled)

This item is used to enable or disable LakeTiny for C state configuration.

This item is used to enable or disable CPU C7 report to OS.

CPU C7 Report (Disabled)

Use this item to enable or disable Package C State limit.

Package C State limit (AUTO)

Hyper-threading (Enabled)

Use this item to enable or disable hyper-threading.

B85H3-M7 USER MANUAL

Chapter 3

Enhanced Halt (C1E) (Enabled)

Use this item to enable the CPU energy-saving function when the system is not running.

Press <Esc> to return to the Advanced Menu page.

B85H3-M7 USER MANUAL

Chapter 3

SATA Configuration

Use this item to show the mode of SATA configuration options.

SATA Mode (AHCI Mode)

Use this item to select SATA mode.

SATA Port 1~4

This motherboard supports four SATA channel and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Determines how SATA Controller(s) operate.

SATA Configuration

SATA Mode AHCI Mode

SATA Port1 Not Present Spin up Device

Disabled

External SATA Disabled

SATA Port2 Not Present Spin up Device Disabled External SATA Disabled

SATA Port3 Not Present Spin up Device Disabled External SATA Disabled

SATA Port4 Not Present Spin up Device Disabled External SATA Disabled

B85H3-M7 USER MANUAL

Chapter 3

USB Configuration

Scroll to this item and press <Enter> to view the following screen:

All USB Devices (Enabled)

Use this item to enable or disable all USB devices.

Legacy USB Support (Enabled)

Use this item to enable or disable support for legacy USB devices. Setting to Audio allows the system to detect the presence of the USB device at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

USB Support Parameters

USB Configuration

All USB Devices Enabled

Legacy USB Support Enabled

B85H3-M7 USER MANUAL

Chapter 3

Super IO Configuration

Use this item to show the information of the Super IO Configuration.

Super IO Chip (IT8728)

This item shows the information of the super IO chip.

Serial Port 0 Configuration

Scroll to this item and press <Enter> to view the following screen:

Press <Esc> to return to the Super IO Configuration page.

Serial Port (Enabled)

This item allows you to enable or disable serial port.

Device Settings (IO=3F8h; IRQ=4)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Serial Port 0 Configuration

Parallel Port Configuration

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Serial Port

Serial Port 0 Configuration

Serial Port Enabled

Device Settings IO=3F8h; IRQ=4;

Change Settings Auto

Set Parameters of Serial Port 0 (COMA)

Super IO Configuration

Super IO Chip IT8728

B85H3-M7 USER MANUAL

Chapter 3

Parallel Port Configuration

Scroll to this item and press <Enter> to view the following screen:

Parallel Port (Enabled)

This item allows you to enable or disable parallel port.

Device Settings (IO=378h; IRQ=5; DMA=3;)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

Device Mode (ECP Mode)

This item shows the information of the device mode.

Press <Esc> to return to the Super IO Configuration page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enabled or Disabled Parallel Port (LPT/LPTE)

Parallel Port Configuration

Parallel Port Enabled

Device Settings IO=378h; IRQ=5; DMA=3;

Change Settings Auto Device Mode ECP Mode

Press <Esc> to return to the Advanced Menu page.

B85H3-M7 USER MANUAL

Chapter 3

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable/Disable Intel(R) Rapid Start Technology.

Intel(R) Rapid Start Technology Disabled

Intel(R) Rapid Start Technology

Use this item to show the information of Intel(R) Rapid Start Technology.

Intel(R) Rapid Start Technology

(Disabled)

Use this item to enable or disable the Intel(R) Rapid Start Technology.

Press <Esc> to return to the Advanced Menu page.

B85H3-M7 USER MANUAL

Chapter 3

Intel(R) Smart Connect Technology

Use this item to show the information of Intel(R) Smart Connect Technology.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable/Disable ISCT Support

ISCT Support Disabled

ISCT Support (Enabled)

Use this item to enable/disable ISCT Support.

B85H3-M7 USER MANUAL

Chapter 3

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable/Disable Intel(R) Active Management Technology BIOS Extension. Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device

Intel AMT Disabled

BIOS Hotkey Pressed Disabled MEBx Selection Screen Disabled

Intel ME BIOS Extension Configuration

Use this item to show the information of Intel ME BIOS Extension Configuration.

Intel AMT (Disabled)

This item just controls the BIOS extension execution. If enabled, this requires

additional firmware in the SPI device.

BISO Hotkey Pressed (Disabled)

This item allows you to enable or disable the BIOS Hotkey Pressed.

MEBx Selection Screen (Disabled)

This item allows you to enable or disable the MEBx selection screen.

B85H3-M7 USER MANUAL

Chapter 3

IGD Multi-Monitor (Disabled)

This item enables or disables IGD (Internal Graphics device) multi-monitor.

System Agent Configuration

Scroll to this item and press <Enter> and view the following screen:

IGD Memory (64M)

This item shows the information of the IGD(Internal Graphics device) memory.

DVMT Memory (256M)

When set to Fixed Mode, the graphics driver will reserve a fixed position of the system memory as graphics memory, according to system and graphics requirements.

Chipset Menu

The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system.

System Agent (SA) Parameters

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

System Agent Configuration PCH Configuration

ME Configuration

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select DVMT 5.0 PreAllocated (Fixed) Graphics Memory size used by the Internal Graphics Device.

System Agent Configuration

IGD Memory 64M

DVMT Memory 256M IGD Multi-Monitor Disabled

CPU SA Audio Device Enabled

CPU SA Audio Device (Enabled)

This item enables or disables CPU SA Audio Device.

B85H3-M7 USER MANUAL

Chapter 3

Press <Esc> to return to the chipset menu page.

Restore AC Power Loss (Power Off)

This item enables your computer to automatically restart or return to its operating status.

Audio Configuration

This item shows the information of the audio configuration.

Azalia HD Audio (Enabled)

This item enables or disables Azalia HD audio.

PCH Configuration

Scroll to this item and press <Enter> to view the following screen:

F4: Save & Exit

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select AC power state when power is re-applied after a power failure

PCH Configuration

Restore AC Power Loss Power Off

Audio Configuration Azalia HD Audio Enabled

Case Open Warning Disabled Chassis Opened No

Case Open Warning (Disabled)

This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case.

Chassis Opened (No)

This item indicates whether the case has been opened.

B85H3-M7 USER MANUAL

Chapter 3

ME Configuration

Scroll to this item and press <Enter> to view the following screen:

ME FW Version (9.0.10.1372)

This item shows the ME FW version.

Press <Esc> to return to the Chipset Menu page.

ME Subsystem Help

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable/Disable ME Firmware

ME Control (Enabled)

Use this item to enable or disable ME Firmware.

Management Engine Technology Configuration

ME Control Enabled

ME FW Version 9.0.10.1372

B85H3-M7 USER MANUAL

Chapter 3

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

M.I.B. III (MB Intelligent BIOS III) Menu

CPU OverClocking Configuration

Scroll to this item to view the following screen:

ME Subsystem Help

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU OverClocking Configuration

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Package Current Lock

M.I.B. III (MB Intelligent BIOS III)

CPU OverClocking Configuration

North Bridge Configuration Memory Configuration Over Voltage Configuration

Spread Spectrum Auto

Intel(R) Core(TM) i7-4765T CPU @ 2.00GHz Processor Speed 2000 MHz Memory Frequency 1333 MHz Total Memory 4096 MB (DDR3)

CPU Ratio 20

Package Current Lock Disabled

IA Core Current Maximum Enhanced Intel SpeedStep Technology Enabled Turbo Mode Enabled RuntimeTurbo Mode Disabled Boot Performance mode Max Non-Turbo Perfor... Package TDP Lock Enable Disabled Long Duration Power Limit Override Maximum Power Limit 1 Time (Second) 8 Power Limit 2 Switch Enabled Short Duration Power Limit Override Maximum 1 Core Ratio Limit 30 2 Core Ratio Limit 29 3 Core Ratio Limit 27 4 Core Ratio Limit 28 Disable OverClocking Lock Enabled

B85H3-M7 USER MANUAL

Chapter 3

Use this item to enable/disable Package Current Lock.

Package Current Lock (Disabled)

IA Core Current (Maximum)

)

Use this item to control CPU Current Limit.

Enhanced Intel SpeedStep Technology (Enabled)

This item allows users to enable or disable the EIST (Enhanced Intel SpeedStep Technology).

Turbo Mode (Enabled)

This item allows you to control the Intel Turbo Boost Technology.

Boot Performance Mode (Max Non-Turbo Perfor...)

Use this item to select the performance state that the BIOS will set before OS handoff.

Package TDP Lock Enable (Disabled)

Use this item to enable/disable Package TDP Lock Enable.

Power Limit 1 Time (Second) (8)

Use this item to set Power Limit 1 Time.

Power Limit 2 Switch (Enabled)

Use this item to control the Power Limit 2. This is for Turbo mode.

1/2/3/4 Core Ratio Limit (30/29/27/28)

These items show the Core Ratio limit value.

Disable OverClocking Lock (Enabled)

Use this item to control OverClocking Lock.

Runtime Turbo Enable (Disabled)

CPU Ratio (20)

This item allows users to control non turbo CPU ratio.

Long Duration Power Limit Override (Maximum)

)

Short Duration Power Limit Override (Maximum) )

This item shows if CPU support Runtime Turbo.

Intel(R) Turbo Boost Technology will use this power limit during the Long Duration Power Limit Time Window.

Intel(R) Turbo Boost Technology will use this power limit for a very short duration. After that, the Long Duration Power Limit will be honored.

Chapter 3

B85H3-M7 USER MANUAL

Graphics Core Ratio Limit (24)

This item allows you to control the internal GFX core ratio.

Press <Esc> to return to the M.I.B. III Menu page.

North Bridge Configuration

Scroll to this item to view the following screen:

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Graphics Core Ratio Limit

Intel Graphics Configuration

Graphics Core Ratio Limit 24

Main Advanced Chipset M.I.B. III Boot Security Exit

Chapter 3

B85H3-M7 USER MANUAL

Main Advanced Chipset M.I.B. III Boot Security Exit

The selection of Memory Profiles which impacts memory sizing behavior.

+/- : Change Opt.





: Select Screen

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Memory Configuration

Scroll to this item to view the following screen:

Memory Information

Memory RC Version 1.6.1.2 Memory Frequency 1333 Mhz Total Memory 4096 MB (DDR3)

Memory Profiles Automatic

Memory Frequency

1333

Timing Default Current Target tCL 9 9 9 tRCD 9 9 9 tRP 9 9 9 tRAS 24 24 24 NMode 1 1 Auto tWR 10 10 10 tRFC 107 107 107 tRRD 4 4 4 tWTR 5 5 5 tRTP 5 5 5 tCWL 7 7 7 tREFI 5200 5200 5200 tFAW 20 20 20 tWRPRE Auto tCPDED Auto tPRPDEN Auto OdtReadDelay Auto tCKE Auto tCCD

tWPRE tRPRE

Auto Auto

Auto

/Click: Select Item

Enter/Dbl Click : Select

Chapter 3

B85H3-M7 USER MANUAL

Memory RC Version (1.6.1.2)

This item shows the information of the memory RC version.

Memory Frequency (1333 Mhz)

This item shows the information of the memory frequency.

Total Memory (4096 MB (DDR3))

This item shows the information of the total memory.

Memory Profiles (Automatic)

This item enables you to set the memory profiles. The selection of memory profiles

impacts memory sizing behavior.

Enh Interleave Support (Enabled)

This item allows you to enable or disable the Enh Interleave support.

RI Support (Enabled)

This item allows you to enable or disable the Rank Interleave support. NOTE: RI and

HORI can not be enabled at the same time.

DLL Weak Lock Support (Enabled)

This item allows you to enable or disable the DLL weak lock support.

Main Advanced Chipset M.I.B. III Boot Security Exit

Enable or disable 2xRef when warm and Hot 2-iNC enables 2xRef when Hot.

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

tCCD Auto tWPRE Auto tRPRE Auto tRDRD Auto tRDRD_dr Auto tRDRD_dd Auto tRDPDEN Auto CMD_3st Auto tWRRD Auto tWRRD_dr Auto tWRRD_dd Auto tWRWR Auto tWRWR_dr Auto tWRWR_dd Auto tWRPDEN Auto Dec_WRD Auto Scomp Auto TcoComp Auto RcompDrvUp Auto RcomDrvDown Auto LsComp Auto

Enh Interleave Support Enabled RI Support Enabled DLL Weak Lock Support Enabled Mc Lock Enabled CMD Tri-State Enabled Memory Scrambler Enabled MRC Fast Boot Enabled Memory Remap Enabled Memory Thermal Management Enabled DDR PowerDown and idle counter BIOS

Refresh 2x Mode Disabled

Chapter 3

B85H3-M7 USER MANUAL

Mc Lock (Enabled)

This item allows you to enable or disable capacity to lock MC registers or not.

CMD Tri-State (Enabled)

This item allows you to enable or disable the CMD Tri-State (ending of the training).

Memory Scrambler (Enabled)

This item allows you to enable or disable the memory scrambler.

MRC Fast Boot (Enabled)

This item allows you to enable or disable the WRC fast boot.

Memory Remap (Enabled)

This item allows you to enable or disable the memory remap above 4G.

Memory Thermal Management (Enabled)

This item allows you to enable or disable the memory thermal management.

DDR PowerDown and Idle counter (BIOS)

This item allows you to BIOS or PCODE the DDR Power Down and Idle counter. BIOS:

BIOS is in countrol of DDR CKE mode and idle timer value. PCODE: pcode will manage the modes.

Refresh 2x Mode (Disabled)

This item allows you to enable or disable 2xRef when warm and Hot 2-iMC enables

2xRef when Hot.

Press <Esc> to return to the M.I.B. III Menu page.

Chapter 3

B85H3-M7 USER MANUAL

ChReadVref 0.744 V (Auto)

This item allows you to adjust the ChReadVref from 0 to 108, and the default is 54, 1 step is 4mV.

Over Voltage Configuration

Scroll to this item to view the following screen:

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Ch0WriteVref 0.744 V (Auto)

This item allows you to adjust the Ch0WriteVref from 0 to 108, and the default is 54, 1 step is 4mV.

Ch1WriteVref 0.744 V (Auto)

This item allows you to adjust the Ch1WriteVref from 0 to 108, and the default is 54, 1 step is 4mV.

ChVrefCA 0.744 V (Auto)

This item allows you to adjust the ChVrefCA from 0 to 108, and the default is 54, 1 step is 4mV.

Ch0WriteVref 0.744V Auto

Ch1WriteVref 0.744 V

Auto

ChVrefCA 0.744V Auto ChReadVref 0.744V

CPU Adaptive Voltage Target(mV) CPU Voltage Mode CPU Voltage Offset(mV) Offset Preflx

RING/Cache Adaptive Voltage Target(mV) 0 RING/Cache Voltage Mode RING/Cache Voltage Offset(mV) Offset Prefix

SVID Control Enable Enabled SVID Override Voltage Target(mV) 0

FIVR Faults Enable Enabled FIVR Efficiency Enable Enabled

GT Adaptive Voltage Target(mV) 0 GT Voltage Mode Adaptive GT Voltage Offset (mV) 0 Offset Prefix +

UNCORE Voltage Offset (mV) 0 Offset Prefix +

IOA Voltage Offset (mV) 0 Offset Prefix +

Auto

Adaptive

Chapter 3

B85H3-M7 USER MANUAL

CPU/RING/Cache/GT Adaptive Voltage Target(mV) (0)

This item allows you to adjust the CPU/RING/Cache/GT Adaptive voltage target from 0 to 2000mV.

CPU/RING/Cache/GT Voltage Mode (Adaptive)

This item allows you to set the CPU/RING/Cache/GT voltage mode.

CPU/RING/Cache/GT/UNCORE/IOA/IOD Voltage Offset(mV) (0)

This item allows you to adjust the CPU/RING/Cache/GT/UNCORE/IOA/IOD voltage offset from -1000 to 998mV.

Offset Prefix (-/+)

This item allows you to select the offset value as positive (+) or negative (-).

SVID Control Enable (Enabled)

This item allows you to enable or disable the SVID control. If this function be disabled, it will not be changed until CPU powers down.

SVID Override Voltage Target(mV) (0)

This item allows you to adjust the SVID override voltage target, up to 2500mV.

FIVR Faults Enable (Enabled)

This item allows you to enable or disable the FIVR faults.

If this function is disabled,

it will not be changed until CPU powers down.

FIVR Efficiency Enable (Enabled)

This item allows you to enable or disable the FIVR efficiency. If this function is dis-

abled, it will not be changed until CPU powers down.

Press <Esc> to return to the M.I.B. III Menu page.

Chapter 3

B85H3-M7 USER MANUAL

Intel(R) Core (TM) i7-4765T CPU @ 2.00GHz

This is display-only field and displays the information of the CPU installed in your computer.

Processor Speed (2000 MHz)

This item shows the CPU speed.

Memory Frequency (1333 MHz)

This item shows the memory frequency.

Total Memory (4096 MB (DDR3))

This item shows the total memory.

Spread Spectrum (Enabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

When end-users encounter failure after attempting over-clocking, please take the following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

Warning: Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

Fail-Safe Procedures for Over-clocking

Chapter 3

B85H3-M7 USER MANUAL

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

This page enables you to set the keyboard NumLock state.

Boot Menu

Boot Configuration

This item shows the information of the Boot Configuration.

Operation System Select (Windows 7 or other OS)

This item is used to select the operation system.

Launch PXE OpROM (Disabled)

The item enables or disables launch PXE Option ROM.

Launch Storage OpROM (Enabled)

Use this item to enable or disable the Storage OpROM.

Fast Boot (Disabled)

This item enables or disables boot with initialization of a minimal set of device required to launch active boot option. Has no effect for BBS boot options.

Bootup NumLock State (On)

This item enables you to select NumLock state.

Quiet Boot (Enabled)

This item enables or disables quiet boot.

Boot mode select (LEGACY)

Use this item to select boot mode.

Set Boot Priority

This item enables you to set boot priority for all boot devices.

Boot Option #1 /2 /3 /4 /5 /6 /7

These items show the boot priorities.

Windows 7 or other OS: Boot policy for Legacy OS.

Windows 8: Boot policy for UEFI OS without Compatibility Support Module(CSM).

Manual: User customized CSM parameters & boot policy.

Boot Configuration

Operation System Select Windows 7 or other OS

Launch PXE OpROM Disabled Launch Storage OpROM Enabled

Fast Boot Disabled

Bootup NumLock State On Quiet Boot Boot mode select

Set Boot Priority Boot Option #1 Hard Disk Boot Option #2 CD/DVD Boot Option #3 USB/Floppy Boot Option #4 USB CD/DVD Boot Option #5 USB Hard Disk Boot Option #6 USB Flash Boot Option #7 Network

Enabled

LEGACY

Chapter 3

B85H3-M7 USER MANUAL

This page enables you to set setup administrator password and user password.

Security Menu

Administrator Password Status (Not Install)

This item shows administrator password installed or not.

User Password Status (Not Install)

This item shows user password installed or not.

Secure Boot (Disabled)

This item is used to control the secure boot flow, it is possible only if system runs in User Mode.

Platform Mode (Setup)

This item allows you to set the platform mode.

Main Advanced Chipset M.I.B. III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Set Administrator Password

Administrator Password

Platform Mode Setup Secure Boot Disabled

Secure Boot

Disabled

Administrator Password Status Not Install User Password Status Not Install

Chapter 3

B85H3-M7 USER MANUAL

Boot Override

Use this item to select the boot device.

Save Options

This item enables you to save the options that you have made.

Save Changes

This item enables you to save the changes that you have made.

Discard Changes

This item enables you to discard any changes that you have made.

Restore Defaults

This item enables you to restore defaults to all the setup options.

Discard Changes and Exit

This item enables you to exit system setup without saving any changes.

Discard Changes and Reset

This item enables you to reset system setup without saving any changes.

This page enables you to exit system setup after saving or without saving the changes.

Exit Menu

Back to EZ Mode

This item enables you to back to EZ mode.

Save Changes and Exit

This item enables you to exitt the system setup after saving the changes.

Save Changes and Reset

This item enables you to reset system setup after saving the changes.

Save as User Defaults

This item enables you to save the changes that you have made as user defaults.

Restore User Defaults

This item enables you to restore the user defaults.

Main Advanced Chipset M.I.B. III Boot Security Exit

Go back to EZ Mode

Back to EZ Mode

Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset

Save Options Save Changes Discard Changes

Restore Defaults Save as User Defaults Restore User Defaults

Boot Override

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Chapter 3

B85H3-M7 USER MANUAL

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Website. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

1 If your motherboard has a BIOS protection jumper, change the setting to

allow BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Ad-

vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)

3 Prepare a bootable device or create a bootable system disk. (Refer to

Windows online help for information on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s

Web site. Copy these files to the bootable device.

5 Turn off your computer and insert the bootable device in your computer.

(You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)

6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file

name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE

040706.ROM

7 When the installation is complete, remove the bootable device from the

computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.

Chapter 3

B85H3-M7 USER MANUAL

Memo

B85H3-M7 USER MANUAL

Chapter 4

Using the Motherboard Software

The auto-install DVD-ROM makes it easy for you to install the drivers and software. The support software DVD-ROM disc loads automatically under Windows XP/7/8. When you insert the DVD-ROM disc in the DVD-ROM drive, the auto-run feature will automatically bring up the installation screen. The screen has four buttons on it:

Setup, Utilities, Browse CD and Exit.

Auto-installing under Windows XP/7/8

Displays the path for all software and drivers available on the disk.

Open Windows Explorer and show the contents of the support disk.

Click “Exit” button to close the Auto-Setup

window.

Browse CD:

Click the “Setup” button to select and run the software installation program.

Click the “ Utilities” button to select and install ECS Intelligent Utility.

Information:

Follow these instructions to install device drivers and software for the motherboard:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

1. Click Setup. The installation program begins:

Running Setup

The motherboard identification is located in the upper left-hand corner.

B85H3-M7 USER MANUAL

Chapter 4

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

5. Follow the instructions on the screen to install the items.

4. Click Next to run the Installation Wizard. An item installation screen appears:

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver.

B85H3-M7 USER MANUAL

Chapter 4

If the auto-install DVD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Look

for the chipset and motherboard model, and then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

Manual Installation

ECS Utility Software (Intelligent EZ Utility)

ECS Intelligent EZ Utility provides friendly interfaces under Windows O.S, which makes your computing more easily and conveniently.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software.

Windows 7/8 will appear below UAC (User Account Control) message after the system restart. You must select “Yes” to install the next driver. Continue

this process to complete the drivers installation.

B85H3-M7 USER MANUAL

Chapter 4

eBLU

ECS eBLU utility makes BIOS update faster and easier. eBLU will list the latest BIOS with a default check-mark. Click”install” button to install.

eDLU

ECS eDLU utility makes updating drivers fast and easy. eDLU saves time and hassle by listing all the latest drivers online. Just select the one you prefer and start to download and install the drivers.

eSF

eSF(Smart Fan) utility provides easy and safe way to adjust fan speed in accordance with your PC’s system loading and temperature.

It has five modes to adjust fan speed in a safe range without entering the BIOS to optimize your system cooling environment.

Microsoft .NET Framework 3.5 is required.

B85H3-M7 USER MANUAL

Chapter 5

Trouble Shooting

Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. You may also log onto our ECS website for more information:

a) System does not power up and the fans are not running.

1. Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Make sure the power cord is plugged into the wall socket & the switch on the Power Supply Unit (PSU) is turned “ on “ as well. Turn on again to see if the CPU and power supply fans are running.

2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.

3. Check the CPU FAN connector is connected to the motherboard.

4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.

5. Check the 12V power connector is connected to the motherboard.

6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.

2. Check the VGA adapter card (if applicable) is inserted properly.

3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps: memory not detected b. 1 long beep and 8 short beeps: VGA not detected

c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Apply the thermal grease onto the CPU heatsink & ensure the CPU fan is well-connected with the CPU heatsink. Check if the CPU fan is working properly while the system is running.

http:// www.ecs.com.tw/ECSWebSite/Support/Support_FAQ.aspx?MenulD=49& childid=M 49&LanlD=0

B85H3-M7 USER MANUAL

Chapter 5

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.

1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.

2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and

Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.

1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.

2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.

3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

4. Remove the hard drive, optical drive or DDR memory to determine which of these components may be at fault.

areas of high moisture content.

3. Routinely clean the CPU cooler fan to remove dust and hair.

4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.

5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.

6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.

Maintenance and care tips

2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.

5. Check whether there is any bulked up electrolytic capacitor or abnormal component.

Please logo onto our ECS website: http://www.ecs.com.tw/ECSWebSite/Support/ Technical_Support_List.aspx?MenuID=50&LanID=0 for more information.

uB rewoP

desserp si no

.trats ot sliaf CP tub

seY

ylppuS rewoP fi kcehC

tinU

gnikrow si )USP(

dnuos peeB ynA

kcehc dna SOMC RLC

rewop V21 UPC fi

detcennoc si

CP eht tratseR

?draob ro USP htiw melborP

AMR tcatnoc >- melborp draob fI

deulp si droc rewop CA gg

?no denrut si hctiws USP dna

seY

melborp draoB

AMR tcatnoc >-

:speeb trohs 3 fI -

ylreporp ton yromem MMID

eruliaf yromem ro detresni

:speeb trohs 8 dna peeb gnol 1 fI -

detceted ton AGV

seY

neercs TSOP ta tlaH

seY

OMC RL dna SC tser .tra

AMR tcatnoc ,liaf fI

seY

eussi ecived larehpireP

.melborp DDH-

,rorre putes SOMC-

d .SOMCRLC ot een

ts ot liaf metsyS elbatsnu ro tra

es SOIB yfidom re

.gn

M SOC RLC tratser dna

hctiws USP no nruT

tekcos llaw ot tcennoc ro

.tratser dna

h rotinom fi kcehC sa

sid

yalp

rotinom fi kcehC

yalpsid sah

Basic Troubleshooting Flowchart

B85H3-M7 USER MANUAL

Chapter 5

Memo

ECS B85H3-M7, H81H3-M7 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual