ECS H61H2-M User Manual

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 1.1C

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.

Other product names used in this manual are the properties of their respective owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Describes features of the motherboard.

Go to

page 1

Describes installation of motherboard components.

Go to

page 7

Go to

page 27

Go to

page 59

Describes the motherboard software

Chapter 2

Installing the Motherboard

Chapter 1

Introducing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Chapter 5

Trouble Shooting

Provides basic trouble shooting tips

page 63

Go to

Provides information on using the BIOS Setup Utility.

iii

Chapter 2

7 7

Installing the Motherboard 7

Safety Precautions............................................................................7

Choosing a Computer Case.............................................................7

Installing the Motherboard in a Case............................................7

Checking Jumper Settings...............................................................8

Setting Jumpers........................................................................8

Checking Jumper Settings......................................................

..9

Jumper Settings......................................................................

..9

Installing Hardware...................................................................10

Installing the Processor..........................................................10

Installing Memory Modules...................................................12

Expansion Slots......................................................................14

Connecting Optional Devices.................................................16

Installing a SATA Hard Drive................................................20

Connecting I/O Devices............................................................... 21

Connecting Case Components.....................................................22

Front Panel Header................................................................25

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...................................................................................1

Feature............................................................................................2

Specifications................................................................................4

Motherboard Components..........................................................5

Chapter 3 27

Using BIOS 27

About the Setup Utility........................ ......................................... 27

The Standard Configuration........................ ...........................27

Entering the Setup Utilities......................................................27

Resetting the Default CMOS Values....................................28

Using BIOS......................................................................................28

BIOS Navigation Key.............................................................29

Main Menu.............................................................................30

Advanced Menu......................................................................31

Chipset Menu..........................................................................44

M.I.B.III (MB Intelligent Bios III) Menu.................................51

Boot Menu...............................................................................55

Security Menu.........................................................................56

Exit Menu...............................................................................57

Updating the BIOS..................................................................58

Chapter 4

59 59

Using the Motherboard Software 59

Auto-installing under Windows XP/7/8......................................59

Running Setup.........................................................................59

Manual Installation...........................................................................61

ECS Utility Software ......................................................................61

Chapter 5

63 63

Trouble Shooting 63

Start up problems during assembly..............................................63

Start up problems after prolong use............................................64

Maintenance and care tips..............................................................64

Basic Troubleshooting Flowchart...................................................65

Introducing the Motherboard

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the H61H2-M motherboard. This motherboard is a high performance, enhanced function motherboard designed to support LGA1155 socket for latest Intel

CoreTM Family/ Pentium® / Celeron® processors*1.

This motherboard is based on Intel

H61 Express Chipset for best desktop platform solution. H61 is a single-chip, highly integrated, high performance Hyper-Threading peripheral controller, unmatched by any other single chip-device controller. This motherboard supports up to 16 GB of system memory with dual channel DDR3 1600

*2/1333/1066 SDRAM. High resolution graphics via PCI Express x16 slot,

intended for Graphics Interface, is fully compliant to the PCI Express Base Specification revision 2.0. It provides two PCI rev 2.2 slots and one PCI Express x1 rev

2.0 slot for extending usage. It implements an EHCI (Enhanced Host Controller Interface) compliant interface that provides eight USB 2.0 ports (four USB 2.0 ports at the back panel and two USB 2.0 headers support additional four USB 2.0 ports and one of Front USB 2.0 headers provide EZ charger technology, please refer to chapter 2 parts of

Front Panel USB headers for more details). This motherboard implements optional USB 3.0 chip which provides two optional USB 3.0 ports at rear I/O with blue connectors also.

The motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and PS/2 keyboard connectors, one DVI port(Co-Lay HDMI Port), one D-sub (VGA) port, one RJ45 LAN connector, four USB 2.0 ports, two USB 3.0 ports (USB 2.0 optional), and audio jacks 6-ch for microphone, line-in and line-out.

In addition, this motherboard supports four SATA 3Gb/s connectors for expansion.

*2 The 3rd Generation CPU required.

*1 When accommodating Intel 3rd Generation CPU, the PCI Express 16X

slot can run at Gen3 speed, which accelerates on 32GB/s rate that effectively delivers double of PCI Express Gen2 speed.

Introducing the Motherboard

Feature

• One PCI Express x16 Gen3 port supporting up to 8 GB/s direction peak bandwidth

“Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical” processors within the same physical processor.

The motherboard uses an LGA1155 type of socket that carries the following features:

Processor

Chipset

• Supports DDR3 1600*/1333/1066 DDR3 SDRAM with Dual-channel architecture

• Accommodates four unbuffered DIMMs

• Up to 4 GB per DIMM with maximum memory size up to 16 GB

Memory

Audio

The Intel H61 Chipset is a single-chip with proven reliability and performance.

• Support one PCI Express x1 slot

• Integrated four SATA 3.0 Gb/s Host Controller

• Eight USB 2.0 ports supported

• Serial Peripheral Interface (SPI) support

• Integrated Graphics Support with PAVP 1.5

• Intel

High Definition Audio Controller

• 5.1+2 Channel High Definition Audio Codec

• Meets Microsoft WLP3.x (Windows Logo Program) audio requirements

• All DACs supports 44.1k/48k/96k/192kHz sample rate

• Software selectable 2.5V/3.2V/4.0V VREFOUT

• Direct Sound 3D. compatible

• Power Support: Digital: 3.3V; Analog: 5.0V

1394a Firewire (Optional)

• Compliant with single chip host controller for IEEE Std 1394-1955 and IEEE 1394a-2000

• Integrated 400 Mb/s 2-Port PHY for the PCI BUS

• 3.3V Power Supply with 5V Tolerant Inputs

•

Latest Intel

CoreTM Family/ Pentium® / Celeron® processors

* The 3rd Generation CPU required.

Introducing the Motherboard

The motherboard comes with the following expansion options:

• One PCI Express x16 slot for Graphic Interface

• One PCI Express x1 slot

• Four SATA 3.0 Gb/s connectors

Expansion Options

The motherboard has a full set of I/O ports and connectors:

Integrated I/O

• One PS/2 keyboard and PS/2 mouse connectors

• One D-sub (VGA) port

• One DVI port (Co-Lay HDMI Port)

• Four USB 2.0 ports

• One RJ45 LAN connector

• Two USB 3.0 ports (USB 2.0 optional)

• Audio jacks 6-ch for microphone, line-in and line-out

The firmware can also be used to set parameters for different processor clock speeds.

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

• Graphic parameters

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system features including the following:

1. Some hardware specifications and software items are subject to change without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50

°C.

Onboard LAN (Optional)

The onboard LAN provides the following features:

• Supports PCI Express

1.1

• Integrated 10/100 transceiver

• Wake-on-LAN and remote wake-up support

• Supports PCI Express

1.1

• Integrated 10/100/1000 transceiver

• Wake-on-LAN and remote wake-up support

Introducing the Motherboard

• Supports “Hyper-Threading” technology CPU

CPU

Specifications

• Intel® H61 Chipset

Chipset

• Dual-channel DDR3 memory architecture

• 4 x 240-pin DDR3 DIMM sockets support up to 16 GB

• Supports 1600

*/1333/1066 DDR3 SDRAM

• 1 x PCI Express x16 Gen3 slot

• 1 x PCI Express x1 Gen2 slot

• 2 x PCI slots

• Supported by Intel

H61 Express Chipset

-4 x Serial ATA 3.0 Gb/s devices

• VIA VT1705 6-Ch HD audio CODEC

• Compliant with HD audio specification

• 1 x PS/2 keyboard and PS/2 mouse connectors

• 1 x D-sub (VGA) port

• 1 x DVI port (Co-Lay HDMI Port)

• 4 x USB 2.0 ports

• 1 x RJ45 LAN connector

• 2 x USB 3.0 ports (USB 2.0 optional)

• Audio jacks 6-ch for microphone, line-in and line-out

Memory

Expansion Slots

Storage

LAN

Rear Panel I/O

• Atheros AR8151 Gigabit Lan (Co-lay Atheros AR8152 10/ 100 LAN)

Audio

• 1 x 24-pin ATX Power Supply connector

• 1 x 4-pin 12V Power connector

• 1 x 4-pin CPU_FAN connector

• 1 x 3-pin SYS_FAN connector

• 1 x Frant Panel audio header

• 1 x Frant Panel switch/LED header

• 1 x Speaker header

• 1 x SPDIF out header

• 4 x Serial SATA 3Gb/s connectors

• 1 x 1394 header (Optional)

• 2 x USB 2.0 headers support additional four USB 2.0 ports (F_USB1 support EZ charger)

• 1 x Chassis intrusion header

• 1 x TPM header

• 1 x Serial port header(COM)

• 1 x Parallel port header(LPT)

• 1 x CLR_CMOS header

Internal I/O Connectors & Headers

LGA1155 socket for latest Intel® CoreTM Family/ Pentium® / Celeron

processors

•

* The 3rd Generation CPU required.

Introducing the Motherboard

Motherboard Components

• AMI BIOS with 32Mb SPI Flash ROM

• Supports Plug and Play, STR(S3)/STD(S4), Hardware monitor, Multi Boot

• Supports ACPI & DMI

• Audio, LAN, can be disabled in BIOS

• F7 hot key for boot up devices option

System BIOS

Form Factor • Micro-ATX Size, 244mm x 220mm

Introducing the Motherboard

Table of Motherboard Components

This concludes Chapter 1. The next chapter explains how to install the motherboard.

LABEL COMPONENTS

LGA1155 socket for Latest Intel

CoreTM Family/Pentium

/ Celeron® processors

2. CPU_FAN 4-pin CPU cooling fan connector

3. DDR3_1~4 240-pin DDR3 SDRAM slots

4. ATX_POWER Standard 24-pin ATX power connector

5. SATA1~2 Serial ATA 3.0 Gb/s connectors

6. SPI_DEBUG SPI debug header-for factory use only

7. SPK Speaker header

8. COM Onboard serial port header

9. SATA3~4 Serial ATA 3.0 Gb/s connectors

10. F_PANEL Front panel switch/LED header

11. F_USB1~2 Front panel USB 2.0 header (F_USB1 supports EZ Charger)

12. CASE CASE open header

13. ME_UNLOCK ME unlock header-for factory use only

14. F_1394A Front 1394 header (Optional)

15. TPM Trusted Platform Module header

16. LPT Printer Header

17. CLR_CMOS Clear CMOS jumper

18. SYS_FAN 3-pin system cooling fan connector

19. SPDIFO SPDIF out header

20. F_AUDIO Front panel audio header

21. PCI1~2 32-bit add-on card slots

22. PCIE1 PCI Express x1 slot

23. PCIEX16 PCI Express slot for graphics interface

24. ATX12V 4-pin +12V power connector

1. CPU Socket

Installing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the Micro ATX system case. Some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries a Micro ATX form factor of 244 x 220 mm. Choose a case that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.

Installing the Motherboard

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT.

SHORT OPEN

Do not over-tighten the screws as this can stress the motherboard.

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

Jumper Settings

To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.

Jumper

Type

Description Setting (default)

CLR_CMOS

3-pin

Clear CMOS

1-2: NORMAL

2-3: CLEAR

Before clearing the CMOS, make sure to turn off the system.

CLR_CMOS

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.

This motherboard has an LGA1155 socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

Warning:

1. Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

Installing the Motherboard

A. Disengaging of the Load Lever

· Press the hook of lever down and pull it to the right side to release it from retention tab.

B. Opening of the Load Plate

· Lift the tail of the load lever.

· Rotate the load plate to fully open position.

C. Removing the Cap

· Be careful not to touch the contact at any time.

D. Inserting the Package

· Grasp the package. Ensure to grasp on the edge of the substrate.

· Make sure pin 1 indicator is on your bottom-left side.

· Aim at the socket and place the package carefully into the socket by purely vertical motion.

E. Closing the Load Plate

· Rotate the load plate onto the package IHS (Intergraded Heat Spreader).

· Engage the load lever while pressing down lightly onto the load plate.

· Secure the load lever with the hook under retention tab.

F. Fasten the cooling fan supporting base onto the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.

CPU Installation Procedure

The following illustration shows CPU installation components.

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin DDR3 1600

*/1333/1066. The total memory capacity is 16 GB.

You must install at least one module in any of the four slots. Total memory capacity is 16 GB.

DDR3 SDRAM memory module table

1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/ heatsink supplied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a CPU.

3. Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1155 socket.

Memory module Memory Bus

DDR3 1066 533 MHz

DDR3 1333 667 MHz

Channel A: DDR3_1, DDR3_2

Channel B: DDR3_3, DDR3_4

The four DDR3 memory sockets (DDR3_1, DDR3_2, DDR3_3 and DDR3_4) are divided into two channels and each channel has two memory sockets as following:

Recommend memory configuration

DDR3_1 DDR3_2 DDR3_3 DDR3_4

1 DIMM Populated

2 DIMMs Populated Populated

Mode

Sockets

4 DIMMs

Populated

(Single Side)

Populated

(Single Side)

Populated

(Single Side)

Populated

(Single Side)

When insert 4 DIMM single side memory, it may run at DDR3 1066.

DDR3 1600 800 MHz

* The 3rd Generation CPU required.

Installing the Motherboard

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR3 SDRAM . 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.

6 Install any remaining DIMM modules.

* For reference only

Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

1. For best performance and compatibility, we recommend that users give priority to the gray DIMMs (DDR3_1/DDR3_3) when installing DIMMs.

2. We suggest users not mix memory type. It is recommended to use the same brand and type memory on this motherboard.

Installing the Motherboard

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

Expansion Slots

The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 2.0.

PCIE1 Slot

PCIEX16 Slot

The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revision 3.0.

This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.2 compliant.

PCI1~2 Slots

Installing the Motherboard

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the

slot you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

2. The onboard PCI interface does not support 64-bit SCSI cards.

1. For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

* For reference only

Installing the Motherboard

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

SATA1~4: Serial ATA connectors

These connectors are used to support the Serial ATA 3.0Gb/s device, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and sofeware compatibility with Prallel ATA.

F_AUDIO: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.

1 PORT 1L 2 AUD_GND 3 PORT 1R 4 PRESENCE# 5 PORT 2R 6 SENSE1_RETURN

7 SENSE_SEND 8 KEY

Pin Signal Name Pin Signal Name

9 PORT 2L 10 SENSE2_RETURN

1 Ground 2 TX+

3 TX- 4 Ground

5 RX- 6 RX+ 7 Ground - -

Pin Signal Name

Installing the Motherboard

F_USB1~2: Front Panel USB 2.0 headers (F_USB1 supports EZ Charger)

The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.

1 USBPWR Front Panel USB Power

2 USBPWR Front Panel USB Power

3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal

5 USB_FP_P0+ USB Port 0 Positive Signal 6 USB_FP_P1+ USB Port 1 Positive Signal

7 GND Ground 8 GND Ground 9 Key No pin

10 NC Not connected

Pin Signal Name Function

Unlike F_USB2 in this mainboard, F_USB1 supports EZ Charger technology, provides 3 times current than general USB port in off mode for USB devices. It is useful and excellent, especially for the iPhone, iPad and iPod touch devices that need a large amount of current for faster recharging within less time.

F_1394A: Front 1394 header (Optional)

Connect this header to any device with IEEE 1394a interface.

1 TPA+ 2 TPA- 3 GND 4 GND 5 TPB+ 6 TPB-

7 Cable-Power 8 Cable-Power

Pin Signal Name Pin Signal Name

9 Key Pin 10 GND

Installing the Motherboard

CASE: Chassis Intrusion Detect Header

Short Chassis cover is removed

Open Chassis cover is closed

This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.

Pin 1-2 Function

ME_UNLOCK: ME Unlock Header

Short Unlock

Open Lock

Pin 1-2 Function

SPDIFO: SPDIF out header

This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.

1 SPDIFOUT

2 VCC 3 KEY

4 GND

Pin Signal Name

COM: Onboard serial port header

Connect a serial port extension bracket to this header to add a serial port to your system.

1 DCDB Data Carrier Detect 2 SINB Serial Input 3 SOUTB UART B Serial Output

4 DTRB UART B Data Ter minal Ready 5 GND Ground 6 DSRB Data Set Ready

7 RTSB RART B Request to Send 8 CTSB Clear to Send

9 RI Ring Indicator

10 Key No pin

Pin Signal Name Function

Installing the Motherboard

LPT: Onboard parallel port Header

This is a header that can be used to connect to the printer, scanner or other devices.

1 STROBE 14 AFD 2 PD0 15 ERROR 3 PD1 16 INIT

4 PD2 17 SLCT 5 PD3 18 Ground 6 PD4 19 Ground

7 PD5 20 Ground 8 PD6 21 Ground

9 PD7 22 Ground

10 ACK 23 Ground

Pin Signal Name Pin Signal Name

11 BUSK 24 Ground

12 PE 25 Ground

13 SLCT 26 Key

TPM(Optional): Trusted Platform Module header

Trusted platform module (TPM) is a published specification detailing a microcontrollerthat can store secured information, and implementations of that specification.

1 TPM_CLK 11 LAD0

2 GND 12 GND

3 LFRAME# 13 RESERVE0

4 KEY 14 RESERVE1

5 LREST# 15 VCC3_DUAL 6 SMBDATA 16 SERIRQ

7 LAD3 17 GND 8 LAD2 18 GND

9 VCC3 19 LPCPD#

10 LAD1 20 SMBCLK

Pin Signal Name Pin Signal Name

Installing the Motherboard

Installing a SATA Hard Drive

This section describes how to install a SATA Hard Drive.

SATA cable

(optional)

SATA power cable (optional)

About SATA Connectors

Your motherboard features four SATA connectors supporting a total of four drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

Installing Serial ATA Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with a SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the

other end to the power supply.

* For reference only

Installing the Motherboard

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

LAN Port

Connect an RJ-45 jack to the LAN port to connect your computer to the Network.

VGA Port Connect your monitor to the VGA port.

Audio Ports

Use the three audio ports to connect audio devices. The first jack is for stereo line-in singal. The second jack is for stereo line-out singal. The third jack is for microphone.

Connect the DVI port to the monitor.

Use the USB 2.0 ports to connect USB 2.0 devices.USB 2.0 Ports

DVI Port (HDMI optional)

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

Use the USB 3.0 ports to connect USB 3.0 devices.

USB 3.0 Ports

Installing the Motherboard

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

The ATX 24-pin connector allows you to connect to ATX v2.x power supply.

With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX match perfectly.

Connecting 24-pin power cable

24-pin power cable

1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the standard power supply connector to ATX_POWER. 3 Connect the case switches and indicator LEDs to the F_PANEL. 4 Connect the system cooling fan connector to SYS_FAN. 5 Connect the auxiliary case power supply connector to ATX12V. 6 Connect the case speaker cable to SPK.

Installing the Motherboard

ATX_POWER: ATX 24-pin Power Connector

Users please note that the fan connector supports the CPU cooling fan of

1.1A ~ 2.2A (26.4W max) at +12V.

CPU_FAN: CPU cooling FAN Power Connector

1 GND System Ground

3 Sense Sensor 4 PWM PWM

Pin Signal Name Function

2 +12V Power +12V

SYS_FAN: System Cooling FAN Power Connector

1 GND System Ground

3 Sense Sensor

Pin Signal Name Function

2 +12V Power +12V

Pin Signal Name Pin Signal Name

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V 3 Ground 15 Ground

4 +5V 16 PS_ON

5 Ground 17 Ground

6 +5V 18 Ground 7 Ground 19 Ground 8 PWRGD 20 -5V

9 +5VSB 21 +5V

10 +12V 22 +5V 11 +12V 23 +5V

12 +3.3V 24 Ground

The ATX12V4P power connector is used to provide power to the CPU.

When installing 4-pin power cable, the latches of power cable and the ATX12V4P match perfectly.

Connecting 4-pin power cable

4-pin power cable

Installing the Motherboard

ATX12V: ATX 12V Power Connector

Pin Signal Name

4 +12V

3 +12V

2 Ground

1 Ground

SPK: Internal speaker

Pin Signal Name

1 VCC 2 Key 3 GND 4 Signal

Installing the Motherboard

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

This concludes Chapter 2. The next chapter covers the BIOS.

Front Panel Header

The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:

Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)

3 HD_LED_N Hard disk LED(- )

5 RST_SW_N Reset Switch(-)

7 RST_SW_P Reset Switch(+)

9 RSVD Reserved

4 FP PWR/SLP *MSG LED(-)

6 PWR_SW_P Power Switch(+)

8 PWR_SW_N Power Switch(-)

10 Key No pin

* MSG LED (dual color or single color)

Installing the Motherboard

Memo

Using BIOS

About the Setup Utility

The computer uses the latest “American Megatrends Inc.” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Press DEL to enter SETUP

Chapter 3

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with an icon



 ) lead to submenus that enable you to change

the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.

Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.

Press the delete key to access BIOS Setup Utility.

Enter/Dbl Click : Select

/Click: Select Item

Choose the system default language

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

BIOS Information

System Language English

System Date

Wed 01/09/2013

System Time 00:00:32

Using BIOS

The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

Scrolls through the items on a menu

+/- Modifies the selected field’s values

F2 Previous Value

F3 Optimized Defaults

F1 General Help

ESC Exits the current menu

mnlk

Enter Select

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by an icon .

F4 Save & Exit

1. For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.

2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select item; Double click: enter; Right click: exit.

Using BIOS

System Date & System Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.

System Language (English)

This item is used to set system language.

When you enter the BIOS Setup program, the main menu appears, giving you an overview of the basic system information. Select an item and press <Enter> to display the submenu.

Main Menu

Choose the system default language

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

BIOS Information

System Language English

System Date

Wed 01/09/2013

System Time 00:00:32

Using BIOS

The Advanced menu items allow you to change the settings for the CPU and other system.

Advanced Menu

LAN Configuration

The item in the menu shows the LAN-related information that the BIOS automatically detects.

ACPI Power Management Configuration

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Onboard LAN Controller (Enabled)

Use this item to enable or disable the Onboard LAN.

Enabled/Disabled Onboard LAN1 Controller

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

LAN Configuration

Onboard LAN Controller Enabled

LAN Configuration PC Health Status ACPI Settings CPU Configuration SATA Configuration USB Configuration Super IO Configuration Intel(R) Smart Connect Technology Trusted Computing Power Management Setup

Press <Esc> to return to the Advanced Menu page.

IEEE 1394 Controller Enabled

Using BIOS

PC Health Status

On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.

Scroll to this item and press <Enter> to view the following screen:

 Smart Fan Function

CPU Smart Fan Control (Enabled)

This item allows you to enable/disable the control of the CPU fan speed by changing the fan voltage.

Smart Fan Mode (Normal)

This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quiet mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjusted depending on users’ parameters.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU Fan Speed : 1584 RPM CPU Voltage : 1.248V AXG Voltage : 0.012V DIMM Voltage : 1.524V

-=- PECI Mode -=-

Offset to TCC Activation Temp. : -54

Smart Fan Function

PC Health Status

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU Smart Fan Control Enabled

Smart Fan Mode

Normal

Smart Fan start PWM value 180 Smart Fan start PWM TEMP(-) 30 Delta T 3 Smart Fan Slope PWM value 10 PWM value/unit CPU Fan Full Speed Offset (-) 23

Using BIOS

• CPU Fan Speed

• CPU Voltage

• AXG Voltage

• DIMM Voltage

System Component Characteristics

These items display the monitoring of the overall inboard hardware health events, such as CPU fan speed, CPU & DIMM voltage...etc.

Press <Esc> to return to the Advanced Menu page.

Press <Esc> to return to the PC Health Status page.

Smart Fan Start PWM value (180)

Smart Fan Start TEMP(-) (30)

This item is used to set the start PWM value of the smart fan.

This item is used to set the start temperature of the smart fan.

DeltaT (3)

This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.

SMART Fan Slope PWM value (10 PWM value/unit)

This item is used to set the Slope Select PWM of the smart fan.

This item is used to set the CPU fan full speed offset value.

CPU Fan Full Speed Offset(-) (23)

Using BIOS

ACPI Setting

The item in the menu shows the highest ACPI sleep state when the system enters suspend.

ACPI Sleep State (S3(Suspend to RAM))

This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).

Press <Esc> to return to the Advanced Menu page.

CPU Configuration

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

ACPI Settings

ACPI Sleep State S3 (Suspend to RAM)

Select the highest ACPI sleep state the system will enter when the suspend button is pressed.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU Configuration

Intel(R) Core(TM) i3-3240 CPU @ 3.40GHz 64-bit Supported Processor Speed 3400 MHz Processor Stepping 206a7 Microcode Revision 28 Processor Cores 2 Intel HT Technology Not Supported Intel VT-x Technology Supported

Active Processor Cores All

Limit CPUID Maximum

Disabled

Execute Disable Bit Enabled Intel Virtualization Technology Enabled CPU C3 Report Disabled CPU C6 Report Enabled Enhanced Halt (C1E) Enabled

Number of cores to enable in each processor package.

Using BIOS

Intel(R) Core(TM) i3-3240 CPU @ 3.40GHz

This is display-only field and diaplays the information of the CPU installed in your computer.

64-bit (Supported)

This item shows the computer supports EMT64.

Processor Speed (3400MHz)

This item shows the current processor speed.

Processor Stepping (206a7)

This item shows the processor stepping version.

Microcode Revision (28)

This item shows the Microcode version.

Processor Cores (2)

This item shows the core number of the processor.

Execute Disable Bit (Enabled)

This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.

Intel Virtualization Technology (Enabled)

When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.

Enhanced Halt (C1E) (Enabled)

Use this item to enable the CPU energy-saving function when the system is not

running.

Press <Esc> to return to the Advanced Menu page.

Limit CPUID Maximum (Disabled)

Use this item to enable or disable the maximum CPUID value limit.

Intel HT Technology (Not supported)

This item shows that your computer supports Intel HT technology or not.

Intel VT-x Technology (Supported)

This item shows that your computer supports Intel VT-x technology or not.

CPU C3 Report (Disabled)

Use this item to enable or disable CPU C3 (ACPI C2) report to OS.

CPU C6 Report (Enabled)

Use this item to enable or disable CPU C6 (ACPI C3) report to OS.

Active Processor Cores (All)

Use this item to control the active processor cores.

Using BIOS

SATA Configuration

Use this item to show the mode of serial SATA configuration options.

SATA Mode (IDE Mode)

Use this item to select SATA mode.

SATA Port 1~4 (Not Present)

This motherboard supports four SATA channel and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.

Press <Esc> to return to the Advanced Menu page.

H61 Chipset is not fully support AHCI Mode. HW supports only.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Determines how SATA Controller(s) operate.

SATA Configuration

SATA Mode IDE Mode

SATA Port1 Not Present

SATA Port2 Not Present

SATA Port3 Not Present

SATA Port4 Not Present

Using BIOS

USB Configuration

Scroll to this item and press <Enter> to view the following screen:

All USB Devices (Enabled)

Use this item to enable or disable all USB devices.

Legacy USB Support (Enabled)

Use this item to enable or disable support for legacy USB devices. Setting to Audio allows the system to detect the presence of the USB device at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

USB Support Parameters

USB Configuration

All USB Devices Enabled

Legacy USB Support Enabled

Using BIOS

Super IO Configuration

Use this item to show the information of the Super IO Configuration.

Super IO Chip (IT8758)

This item shows the information of the super IO chip.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Super IO Configuration

Super IO Chip IT8758 Serial Port 0 Configuration Parallel Port Configuration

Set Parameters of Serial Port 0 (COMA)

Using BIOS

 Serial Port 0 Configuration

Scroll to this item and press <Enter> to view the following screen:

Serial Port (Enabled)

This item allows you to enable or disable serial port.

Device Settings (IO=3F 8h; IRQ=4)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

Press <Esc> to return to the Super IO Configuration page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enabled or Diabled Serial Port (COM)

Serial Port 0 Configuration

Serial Port Enabled

Device Settings IO=3F8h; IRQ=4;

Change Settings

Auto

Using BIOS

 Parallel Port Configuration

Scroll to this item and press <Enter> to view the following screen:

Parallel Port (Enabled)

This item allows you to enable or disable parallel port.

Device Settings (IO=378h; IRQ=5)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

Press <Esc> to return to the Super IO Configuration page.

Press <Esc> to return to the Advanced Menu page.

Device Mode (Standard Parallel...)

Use this item to select device mode.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Parallel Port Configuration

Parallel Port Enabled

Device Settings IO=378h; IRQ=5

Enable or Disable Parallel Port (LPT/LPTE)

Change Settings Auto Device Mode Standard Parallel Po...

Using BIOS

Intel(R) Smart Connect Technology

Use this item to show the information of Intel(R) Smart Connect Technology.

ISCT Configuration (Disabled)

Use this item to enable/disable ISCT Configuration.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enabled/Disabled ISCT Configuration

Press <Esc> to return to the Advanced Menu page.

ISCT Configuration Disabled

Using BIOS

Trusted Computing

Scroll to this item and press <Enter> to view the following screen.

TPM Support (Enabled)

This item enables or disables TPM support.

Current Status Information

This item shows the information of current status.

NO Security Device Found

This item shows no security device.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

TPM Configuration

TPM Support Enabled

Current TPM Status Information NO TPM Hardware

Enables or Disables BIOS support for security device.O.S. will not show Security Device. TDG EFI protocol and INT1A interface will not be available.

Using BIOS

EUP Function (Enabled)

This item allows user to enable or disable EUP function.

Resume By PS2 MS (S3) (Disabled)

This item enables or disables you to allow mouse activity to awaken the system from power saving mode.

Power Management Setup

This page sets up some parameters for system power management operation.

Resume By PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card.

Resume By USB 1.x/2.0(S3) (Disabled)

This item allows you to enable/disable the USB device wakeup function from S3 mode.

Resume By RING (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem. You must use an ATX power supply in order to use this feature.

Resume By PS2 KB (S3) (Disabled)

This item enables or disables you to allow keyboard activity to awaken the system from power saving mode.

Power LED Type (Dual Color LED)

This item shows the type of the power LED.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

About Resume by Ring

Power Management Setup

Resume By RING Disabled

Resume By PME

Disabled

Resume By USB 1.x/2.0 (S3) Disabled Resume By PS2 KB (S3) Disabled Resume By PS2 MS (S3) Disabled EUP Function Enabled Power LED Type Dual Color LED

Using BIOS

IGD Multi-Monitor (Disabled)

This item enables or disables IGD (Internal Graphics device) multi-monitor.

System Agent Configuration

Scroll to this item and press <Enter> and view the following screen:

IGD Memory (64M)

This item shows the information of the IGD(Internal Graphics device) memory.

DVMT Memory (256M)

When set to Fixed Mode, the graphics driver will reserve a fixed position of the system memory as graphics memory, according to system and graphics requirements.

The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system.

Chipset Menu

Initiate Graphic Adapter (Auto)

This item allows you to select graphics controller to use as the primary boot device.

System Agent (SA) Parameters

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

System Agent Configuration

PCH Configuration

ME Configuration

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

System Agent Configuration

Initiate Graphic Adapter Auto

IGD Memory

64M

DVMT Memory 256M IGD Multi-Monitor Disabled

Select which of IGFX/PEG/ PCI Graphics device should be Primary Display or Select SG for Switchable Gfx.

Using BIOS

Press <Esc> to return to the chipset menu page.

Multi-Monitor technology

Please note that Multi-Monitor technology supports up to four monitors: one or two Intel integrated Graphics and one or two PCI-Express graphics devices under Windows 7/8.

Multi-Monitor technology can help you to increase the area available for programs running on a single computer system through using multiple display devices.

It is not only to increase larger screen viewing but aslo to improving personal productivity.

Step 1. Insert ECS drives DVD to run Auto setup or browse the DVD to install Intel chipset drivers, VGA and sound drivers.(If you want know the detail information, please refer to chapter 4.)

Intel Integrated Graphics

PCI-Express Graphics

Using BIOS

Step 3. Enable IGD Multi-Monitor from BIOS. In the following BIOS screen, please set IGD Multi-Monitor to [Enabled].

Step 2. Install all the drivers of PCI-Express graphic cards. Click the Browse CD item, then appears the following screen. Select the driver you want to install(e.g NVIDIA GeForce 8400 GS(Microsoft Corporation-WDDM v1.1)) and double click it.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

System Agent Configuration

Initiate Graphic Adapter Auto

IGD Memory

64M

DVMT Memory 256M IGD Multi-Monitor Enabled

Select which of IGFX/PEG/ PCI Graphics device should be Primary Display or Select SG for Switchable Gfx.

Using BIOS

2.Select display devices, set the multiple displays option and to extend destop for display “Multi-Monitor technology”.

Change the apearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

3. DELL U2410Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Disconnect this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

You must select Apply before making additional changes.!

Extend desktop to this display Disconnect this display

Step 4. Change the appearance of your displays under Windows 7/8.

Change the appearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

1. DELL U2410Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Extend desktop to this displayMultiple displays:

This is currently your main display.

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

Show the path of the setting location

Display devices

The type of the display

Set the multiple displays

1. Enter the Control Panel menu, select the Display in the All Control Panel Items and click the Screen Resolution, then appears the following screen.

Using BIOS

Change the appearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

4. AL1717Display:

Resolution: 1920 x 1200 (recommended)

Orientation: Landscape

Disconnect this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

You must select Apply before making additional changes.

Change the appearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

4. AL1717Display:

Resolution: 1920 x 1200 (recommended)

Orientation: Landscape

Extend desktop to this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

You must select Apply before making additional changes.

Using BIOS

 PCH Configuration

Scroll to this item and press <Enter> to view the following screen:

Restore AC Power Loss (Power Off)

This item enables your computer to automatically restart or return to its operating status.

Audio Configuration

This item shows the information of the audio configuration.

Azalia HD Audio (Enabled)

This item enables or disables Azalia HD audio.

Azalia internal HDMI codec (Enabled)

This item enables or disables Azaia internal HDMI codec.

Case Open Warning (Disabled)

This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case.

Chassis Opened (No)

This item indicates whether the case has been opened.

Press <Esc> to return to the chipset menu page.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select AC power state when power is re-applied after a power failure

PCH Configuration

Restore AC Power Loss Power Off

Audio Configuration Azalia HD Audio

Enabled

Azalia internal HDMI codec Enabled

Case Open Warning Disabled Chassis Opened No

Using BIOS

 ME Configuration

Scroll to this item and press <Enter> to view the following screen:

ME FW Version (8.1.0.1248)

This item shows the ME version.

Press <Esc> to return to the chipset menu page.

ME Subsystem Help

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Management Engine Technology Configuration

ME FW Version 8.1.0.1248

Using BIOS

 CPU OverClocking Configuration

Scroll to this item to view the following screen:

CPU Ratio (30)

This item allows users to control non turbo CPU ratio.

CPU Frequency (100)

This item shows the information of the CPU frequency.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU OverClocking Configuration

CPU Frequency 100 CPU Ratio 30

Enhanced Intel SpeedStep Technology Enabled

Intel Graphics Configuration

Graphics Core Ratio Limit 22 Graphics Voltage(1/256) 0

Enhanced Intel SpeedStep Technology

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

M.I.B III (MB Intelligent BIOS III) Menu

ME Subsystem Help

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU OverClocking Configuration

M.I.B III (MB Intelligent BIOS III)

CPU OverClocking Configuration Chipset OverClocking Configuration

B.O.M.P Technology Enabled

Auto Detect DIMM/PCI Clk Enabled Spread Spectrum Enabled

Intel(R) Core (TM) i3-3240 CPU @ 3.40GHz Processor Speed 3400 MHz Memory Frequency 1333 MHz Total Memory 1024 MB (DDR3 )

Using BIOS

Enhanced Intel SpeedStep Technology (Enabled)

This item allows users to enable or disable the EIST(Enhanced Intel SpeedStep Technology).

Graphics Voltage(1/256) (0)

This item allows you to adjust the internal GFX voltage.

Graphics Core Ratio Limit (22)

This item allows you to control the internal GFX Turbo ratio

Using BIOS

 Chipset OverClocking Configuration

Scroll to this item to view the following screen:

Row Precharge Time (tRP) (9)

This item specifies Row precharge to Active or Auto-Refresh of the same bank.

CAS Latency (tCL) (9)

This item determines the operation of DDR SDRAM memory CAS (colulmn address strobe). It is recommended that you leave this item at the default value. The 2T setting requires faster memory that specifically supports this mode.

RAS# to CAS# Delay (tRCD) (9)

This item specifies the RAS# to CAS# delay to Rd/Wr command to the same bank.

Row Refresh Cycle Time (tRFC) (74)

This item specifies the row refresh cycle time.

RAS# Active Time (tRAS) (24)

This item specifies the RAS# active time.

Write Recovery Time (tWR) (10)

This item specifies the write recovery time.

Active to Active Delay (tRRDmin) (4)

This item controls the ACTIVE bank x to ACTIVE bank y in memory clock cycles.

Read CAS# Precharge (tRTP) (5)

Write to Read Delay (twTR) (5)

This item specifies the write to read delay time.

This item controls the Read to PRECHARGE delay for memory devices, in memory clock cycles.

Main Advanced Chipset M.I.B III Boot Security Exit

Memory Multiplier Configuration

Performance Memory Profiles Automatic XMP Profile 1 Supported XMP Profile 2 Supported

Memory Timing Configuration

CAS# Latency (tCL) 9 RAS# to CAS# Delay (tRCD) 9 Row Precharge Time (tRP) 9 RAS# Active Time ( tRAS) 24 Write Recovery Time (tWR) 10 Row Refresh Cycle Time (tRFC) 74 Active to Active Delay (tRRD) 4 Write to Read Delay (tWTR) 5 Read CAS# Precharge (tRTP) 5 Four Active Window Delay (tFAW) 20

The selection of Performance Memory Profiles which impacts memory sizing behavior.

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Performance Memory Profiles (Automatic)

This item enables you to set the Performance Memory Profile.

XMP Profile 1/2 (Supported)

These items show the information of Performance Memory Profile.

Using BIOS

B.O.M.P Technology (Enabled)

This item allows users to enable or disable B.O.M.P technology. This function can run safe setting to setup menu when system boot fail 3 times.

Spread Spectrum (Enabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

Intel(R) Core(TM) i3-3240 CPU @ 3.40GHz

This is display-only field and displays the information of the CPU installed in your computer.

Processor Speed (3400 MHz)

This item shows the CPU speed.

Memory Frequency (1333MHz)

This item shows the memory frequency.

Auto Detect DIMM/PCI Clk (Enabled)

When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.

Total Memory (1024MB(DDR3))

This item shows the total memory of DDR3.

This item controls the four bank activate time in memory clock cycles.

Four Active Window Delay (tFAW) (20)

Press <Esc> to return to the M.I.B III menu page.

Using BIOS

This page enables you to set the keyboard NumLock state.

Boot Menu

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values

Windows 7 or other OS: Boot policy for Legacy OS

Windows 8: Boot Policy for UEFI OS without Compatibility Support Module (CSM)

Manual: User customized CSM parameters & boot policy

F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Boot Configuration

This item shows the information of the Boot Configuration.

Bootup NumLock State (On)

This item enables you to select NumLock state.

Quiet Boot

(Enabled)

This item enables or disables quiet boot.

Boot mode select (LEGACY)

Use this item to select boot mode.

Operation System Select (Windows7 or other OS)

This item is used to select the operation system.

Boot Configuration

Launch PXE OpROM (Disabled)

The item enables or disables launch PXE Option ROM.

Launch Storage OpROM (Enabled)

The item enables or disables launch Storage Option ROM.

Set Boot Priority

This item enables you to set boot priority for all boot devices.

Boot Option #1/2/3/4/5/6/7

These items show the boot priorities.

Operation System Select Windows7 or other OS Launch PXE OpROM

Disabled

Launch Storage OpROM Enabled

Fast Boot Disabled

Bootup NumLock State On Quiet Boot Enabled Boot mode select LEGACY

Set Boot Priority Boot Option #1 Hard Disk Boot Option #2 CD/DVD Boot Option #3 USB/Floppy Boot Option #4 USB CD/DVD Boot Option #5 USB Hard Disk Boot Option #6 USB Flash Boot Option #7 Network

Fast Boot (Disabled)

This item enables or disables fast boot.

Using BIOS

This page enables you to set setup administrator password and user password.

Security Menu

Administrator Password Status (Not Install)

This item shows administrator password installed or not.

User Password Status (Not Install)

This item shows user password installed or not.

System Mode state (Setup)

This item shows system mode setup or not.

Secure Boot state (Disabled)

This item allows you to enable or disable the secure boot state.

Secure Boot (Disabled)

This item is used to control the secure boot flow, it is possible only if system runs in User Mode.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values

Set Administrator Password

F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Administrator Password Status Not Install User Password Status Not Install

Administrator Password

System Mode state Setup Secure Boot state Disabled

Secure Boot Disabled

Using BIOS

Boot Override

Use this item to select the boot device.

This page enables you to exit system setup after saving or without saving the changes.

Exit Menu

Save Changes and Reset

This item enables you to save the changes that you have made and resit.

Discard Changes and Exit

This item enables you to discard any changes that you have made and exit.

Save Options

This item enables you to save the options that you have made.

Save Changes

This item enables you to save the changes that you have made.

Discard Changes

This item enables you to discard any changes that you have made.

Restore Defaults

This item enables you to restore the system defaults.

Save as User Defaults

This item enables you to save the changes that you have made as user defaults.

Restore User Defaults

This item enables you to restore user defaults.

Discard Changes and Reset

This item enables you to discard any changes that you have made and reset.

Main Advanced Chipset M.I.B III Boot Security Exit

+/- : Change Opt.

Enter/Dbl Click : Select

: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values

Reset the system after saving the changes.

F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Save Changes and Reset

Discard Changes and Exit Discard Changes and Reset

Save Options Save Changes Discard Changes

Restore Defaults Save as User Defaults Restore User Defaults

Boot Override

Using BIOS

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

1 If your motherboard has a BIOS protection jumper, change the setting to

allow BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Ad-

vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)

3 Prepare a bootable device or create a bootable system disk. (Refer to

Windows online help for information on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s

Web site. Copy these files to the bootable device.

5 Turn off your computer and insert the bootable device in your com-

puter. (You might need to run the Setup Utility and change the the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)

6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file

name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE

040706.ROM

7 When the installation is complete, remove the bootable device from the

computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.

Using the Motherboard Software

Chapter 4

Using the Motherboard Software

The auto-install DVD-ROM makes it easy for you to install the drivers and software. The support software DVD-ROM disc loads automatically under Windows XP/7/8. When you insert the DVD-ROM disc in the DVD-ROM drive, the auto-run feature will automatically bring up the installation screen. The screen has four buttons on it:

Setup, Utilities, Browse CD and Exit.

Auto-installing under Windows XP/7/8

Displays the path for all software and drivers available on the disk.

Open Windows Explorer and show the contents of the support disk.

Click “Exit” button to close the Auto-Setup

window.

Browse CD:

Click the “Setup” button to select and run the software installation program.

Click the “ Utilities” button to select and install ECS Intelligent Utility.

Information:

Follow these instructions to install device drivers and software for the motherboard:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

1. Click Setup. The installation program begins:

Running Setup

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver.

4. Click Next to run the Installation Wizard. An item installation screen appears:

Using the Motherboard Software

Windows 7/8 will appear below UAC (User Account Control) message after the system restart. You must select “Yes” to install the next driver. Continue this process to complete the drivers installation.

If the auto-install DVD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer).

Look for the chipset and motherboard model, and then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

Manual Installation

ECS Utility Software (Intelligent EZ Utility)

ECS Intelligent EZ Utility provides friendly interfaces under Windows O.S, which makes your computing more easily and conveniently.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software.

Using the Motherboard Software

eBLU

ECS eBLU utility makes BIOS update faster and easier. eBLU will list the latest BIOS with a default check-mark. Click”install” button to install.

eDLU

ECS eDLU utility makes updating drivers fast and easy. eDLU saves time and hassle by listing all the latest drivers online. Just select the one you prefer and start to download and install the drivers.

eSF

eSF(Smart Fan) utility provides easy and safe way to adjust fan speed in accordance with your PC’s system loading and temperature.

It has five modes to adjust fan speed in a safe range without entering the BIOS to optimize your system cooling environment.

Microsoft .NET Framework 3.5 is required.

Trouble Shooting

Chapter 5

Trouble Shooting

Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips.

a) System does not power up and the fans are not running.

1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Turn on again to see if the CPU and power supply fans are running.

2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.

3. Check the CPU FAN connector is connected to the motherboard.

4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.

5. Check the 12V power connector is connected to the motherboard.

6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.

2. Check the VGA adapter card (if applicable) is inserted properly.

3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps: memory not detected b. 1 long beep and 8 short beeps: VGA not detected

c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly.

Trouble Shooting

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.

Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.

1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.

2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.

3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

4. Remove the hard drive, optical drive or DDR memory to determine which of these components may be at fault.

Maintenance and care tips

2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.

1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.

2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and areas of high moisture content.

3. Routinely clean the CPU cooler fan to remove dust and hair.

4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humility.

5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.

6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.

Power Bu

on is pressed

but PC fails to start.

Yes

Check if Power Supply

Unit

(PSU) is working

Any Beep soundΛ

CLR CMOS and check

if CPU 12V power

is connected

art the PC stRe

Problem with PSU or board?

If board problem -> contact RMA

AC power cord is plu ed g

and PSU switch is turned on?

Yes

oblem rBoard p

-> contact RMA

- If 3 short beeps:

DIMM memory not properly

inserted or memory failure

- If 1 long beep and 8 short beeps:

VGA not detected

Yes

Halt at POST screenΛ

Yes

R CMOLC S and rest

art.

If fail, contact RMA

Yes

Peripheral device issue

- HDD problem.

- CMOS setup error,

dnee to CLRCMOS.

System fail to start or unstable

er modify BIOS se

ng.

MCLR C OS and restart

Turn on PSU switch

or connect to wall socket

start. e

and r

Check if monitor h

s a

dis

play

Check if monitor

has display

Basic Troubleshooting Flowchart

Trouble Shooting

Memo

ECS H61H2-M User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual