ECS H61H2-A User Manual
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 2.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Chapter 5
Ò
Intel
Matrix Storage Manager
RAID Configurations
Chapter 6
Trouble Shooting
Describes features of the
motherboard
Go to
Describes installation of
motherboard components
Go to
Provides information on using
the BIOS Setup Utility
Go to
Describes the motherboard
software
Go to
Describes the Intel
Storage Manager RAID
Configurations
Go to
Provides basic trouble shooting tips
Go to
H
H
H
H
H
H
page 1
page 7
page 25
page 58
®®
®
®®
Matrix
page 63
page 69
Preface
TT
ABLE OF CONTENTSABLE OF CONTENTS
T
ABLE OF CONTENTS
TT
ABLE OF CONTENTSABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction....................................................................................1
Feature................................................................................................2
Specifications...................................................................................4
Motherboard Components...........................................................5
iii
Chapter 2
Installing the Motherboard 7
Safety Precautions...........................................................................7
Choosing a Computer Case............................................................7
Installing the Motherboard in a Case...........................................7
Checking Jumper Settings..............................................................8
Setting Jumpers.......................................................................8
Checking Jumper Settings.......................................................9
Jumper Settings.......................................................................9
Installing Hardware...................................................................10
Installing the Processor........................................................10
Installing Memory Modules..................................................12
Expansion Slots.....................................................................14
Connecting Optional Devices...............................................16
Installing a SATA Hard Drive...............................................19
Connecting I/O Devices................................................................20
Connecting Case Components.....................................................21
Front Panel Header...............................................................24
Chapter 3 25
Using BIOS 25
About the Setup Utility........................ ......................................... 25
The Standard Configuration...................................................25
Entering the Setup Utilities....................................................25
Resetting the Default CMOS Values..................................26
Using BIOS......................................................................................26
BIOS Navigation Key.............................................................27
Main Menu............................................................................27
Advanced Menu.....................................................................28
Chipset Menu
M.I.B. III(MB Intelligent BIOS III) Menu..............................48
Boot Menu
.........................................................................41
..............................................................................53
7 7
7
7 7
iv
Security Menu.........................................................................54
Exit Menu................................................................................55
Updating the BIOS..................................................................57
Chapter 4
Using the Motherboard Software 59
About the Software DVD-ROM/CD-ROM.................................59
Auto-installing under Windows XP/Vista/7...............................59
Running Setup..........................................................................60
Manual Installation........................................................................62
Utility Software Reference.........................................................62
Chapter 5
Intel® Matrix Storage Manager RAID Configurations 63
Before creating a RAID set.............................................................63
Entering Intel
Creating a RAID set........................................................................65
Deleting a RAID set........................................................................67
Resetting disks to Non-RAID.......................................................68
Exiting Setup....................................................................................68
®
Matrix Storage Manager RAID BIOS utility....64
Chapter 6
Trouble Shooting 69
Start up problems during assembly..............................................69
Start up problems after prolong use............................................70
Maintenance and care tips..............................................................70
Basic Troubleshooting Flowchart...................................................71
59 59
59
59 59
63 63
63
63 63
69 69
69
69 69
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing H61H2-A motherboard. This motherboard is a high
performance, enhanced-function motherboard designed to support the LGA1155
socket for latest Intel
optimum system performance for high-end business or personal desktop market.
This motherboard is based on Intel
H61 is a single-chip, highly integrated, high performance Hyper-Threading peripheral controller, unmatched by any other single chip-device controller. This
motherboard supports up to 16 GB of system memory with dual channel DDR3
1333/1066 SDRAM. It supports one PCIe x16 graphic interface, that allows you
install up to one graphic card with multiple GPU. It provides two PCI rev 2.2 slots
and three PCI Express x1 rev 2.0 slots for extending usage. It provides standard
eight USB 2.0 ports (four rear I/O ports and two headers support additional four USB
2.0 ports and one of Front USB 2.0 headers provide EZ charger technology, please
refer to chapter 2 parts of
The motherboard is equipped with advanced full set of I/O ports in the rear panel,
including one PS/2 mouse and PS/2 keyboard connectors, one LAN port, four USB
2.0 ports, one VGA port, and audio jacks for microphone, line-in and 6-ch line-out.
*When accommodating Intel 3rd Generation CPU, the PCI Express 16X
slot can run at Gen3 speed, which accelerates on 32GB/s rate that
effectively delivers double of PCI Express Gen2 speed.
®
CoreTM Family/Pentium®/Celeron® processors* to reach the
®
H61 Chipset for best desktop platform solution.
Front Panel USB headers for more details).
1
Introducing the Motherboard
2
Feature
Processor
The motherboard uses an LGA1155 type of socket that carries the following
features:
• Supports 22nm & 32nm Intel® CoreTM micro-architecture
• DMI 5.0GT/s
• Supports “Hyper-Threading” technology CPU
• One PCI Express x16 slot
“Hyper-Threading” technology enables the operating system into thinking
it’s hooked up to two processors, allowing two threads to be run in parallel, both
on separate “logical” processors within the same physical processor.
Chipset
The Intel® H61 Chipset is a single-chip with proven reliability and performance.
• Supports three PCI Express x1 Gen2 slots
• Integrated four SATA 3.0 Gb/s Host Controllers
• Ten USB 2.0 ports supported
• Serial Peripheral Interface (SPI) support
• Integrated DirectX 10.1 graphics processor
• Supports Intel
®
HD Graphics
Extra Chips
• ITE IT8893 PCI Bridge supports two PCI slots expansion
Memory
• Supports DDR3 1333/1066 DDR3 SDRAM with Dual-channel architecture
• Accommodates two unbuffered DIMMs
• Up to 8 GB per DIMM with maximum memory size up to 16 GB
Audio
• 5.1+2 Channel High Definition Audio Codec
• Meets Microsoft WLP3.x (Windows Logo Program) audio
• All DACs supports 44.1k/48k/96k/192kHz sample rate
• Software selectable 2.5V/3.2V/4.0V VREFOUT
• Direct Sound 3D. compatible
• Power Support: Digital: 3.3V; Analog: 5.0V
requirements
Introducing the Motherboard
Onboard LAN (Optional)
The onboard LAN provides the following features:
TM
TM
1.1
1.1
• Supports PCI Express
• Integrated 10/100/1000 transceiver
• Wake-on-LAN and remote wake-up support
• Supports PCI Express
• Integrated 10/100 transceiver
• Wake-on-LAN and remote wake-up support
Expansion Options
The motherboard comes with the following expansion options:
• One PCI Express x16 slot for Graphic Interface
• Three PCI Express x1 slots
• Two 32-bit PCI v2.2 compliant slots
• Four 7-pin SATA 3.0 Gb/s connectors
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• One D-sub port
• One DVI port (Optional)
• Six USB 2.0 ports (Two ports are optional)
• One PS/2 keyboard and PS/2 mouse connectors
• One RJ-45 port
• Audio jacks for microphone, line-in and 6-ch line-out
3
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure many system
features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1. Some hardware specifications and software items are subject to change
without prior notice.
2. Due to chipset limitation, we recommend that motherboard be operated
in the ambiance between 0 and 50
°C.
Introducing the Motherboard
4
Specifications
CPU
Chipset
Extra Chips
Memory
Expansion
Slots
Storage
Audio
LAN
Rear Panel I/O
Internal I/O
Connectors &
Headers
System BIOS
• LGA1155 socket for latest Intel® CoreTM Family/Pentium®/
• DMI 5.0GT/s
• Supports “Hyper-Threading” technology CPU
• Intel® H61 Chipset
• ITE IT8893 PCI Bridge supports two PCI slots expansion
• Dual-channel DDR3 memory architecture
• 2 x 240-pin DDR3 DIMM sockets support up to 16 GB
• Supports DDR3 1333/1066
• 1 x PCI Express x16 slot
• 3 x PCI Express x1 slots
• 2 x PCI slots
• Supported by Intel
- 4 x SATA 3.0 Gb/s Host Controllers
• Realtek ALC662 6-Ch High Definition audio CODEC
• Compliant with HD audio specification
• Realteck 8111E Gigabit Fast Ethernet (Co-lay 10/100)
• 1 x PS/2 keyboard & PS/2 mouse connectors
• 1 x D-sub port
• 1 x DVI port (optional)
• 1 x RJ-45 port
• 1 x Audio port (Line in, Microphone in, Line out)
• 4 x USB 2.0 ports & 2 ports (optional)
• 1 x 24-pin ATX Power Supply connector
• 1 x 4-pin 12V Power connector
• 1 x Speaker header
• 1 x Front panel switch/LED header
• 1 x Front Panel audio header
• 1 x S/PDIF out header
• 1 x CLR_CMOS header
• 1 x Serial port header (COM)
• 1 x Parallel port header (LPT)
• 4 x SATA II 3Gb/s connectors
• 2 x USB2.0 headers support additional four USB 2.0 ports
• 1 x ME UNLOCK header
• 1 x Chassis intrusion header
• 1 x 4-pin CPU_FAN connector
• 1 x 3-pin SYS_FAN connector
• 1 x 3-pin PWR_FAN connector
• AMI BIOS with 64 Mb SPI Flash ROM
• Supports Plug and Play, STR(S3)/STD(S4), Hardware moni-
®
Celeron
(F_USB2 supports EZ Charger)
tor, Multi Boot
processors
®
H61 Chipsets
Introducing the Motherboard
• Supports ACPI & DMI, Watch dog
• Audio, LAN, can be disabled in BIOS
• F7 hot key for boot up devices option
• Supports eBLU/eDLU/eSF
• Supports PgUp clear CMOS Hotkey (Has PS2 KB Model only)
• Supports ACPI 3.0 revision
• Supports ECS M.I.B III Utility, GPU Voltage Adjustable, MultiLanguage BIOS
• Supports GUI UEFI
Form Factor • ATX Size, 305mm x 195mm
Motherboard Components
5
Introducing the Motherboard
6
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket
LGA1155 socket for latest Intel
®
Celeron
processors
®
CoreTM Family/Pentium®/
2. CPU_FAN CPU cooling fan connector
3. DDR3_1~2 240-pin DDR3 SDRAM slots
4. ATX_POWER Standard 24-pin ATX power connector
5. SYS_FAN System cooling fan connector
6. SATA1~4 SATA 3Gb/s connectors
7. PWR_FAN Power cooling fan connector
8. F_PANEL Front panel switch/LED header
9. SPI_DEBUG SPI debug header-for factory use only
10. F_USB2 Front panel USB 2.0 header (F_USB2 supports EZ Charger)
11. F_USB1 Front panel USB 2.0 header
12. CLR_CMOS Clear CMOS jumper
13. SPK Internal speaker header
14. COM Onboard serial port header
15. CASE CASE open header
16. ME_UNLOCK ME unlock header-for factory use only
17. LPT Parallel port header
18. F_AUDIO Front panel audio header
19. SPDIFO SPDIF out header
20. PCI1~2 32-bit add-on card slots
21. PCIE1~3 PCI Express x1 slots
22. PCIEX16 PCI Express x16 slot for graphics interface
23. ATX12V 4-pin +12V power connector
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid damage from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies
with the specifications for the ATX system case. Some features on the motherboard
are implemented by cabling connectors on the motherboard to indicators and switches
on the system case. Make sure that your case supports all the features required.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries an ATX form factor of 305 x 195 mm. Choose a case that
accommodates this form factor.
7
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in
a case.
Most system cases have mounting brackets installed in the case, which correspond
the holes in the motherboard. Place the motherboard over the mounting brackets
and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion
slots on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the jumper
caps are placed on the correct pins.
The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.
This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT.
SHORT OPEN
Installing the Motherboard
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is
labeled.
9
Jumper Settings
Jumper
CLR_CMOS
To avoid the system instability after clearing CMOS, we recommend
users to enter the main BIOS setting page to “Load Default Settings”
and then “Save and Exit Setup”.
Type
Description Setting (default)
1-2: NORMAL
3-pin
Clear CMOS
2-3: CLEAR
Before clearing the
CMOS, make sure to
turn off the system.
Installing the Motherboard
1
CLR_CMOS
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes
across the motherboard, you may cause serious damage to the motherboard
or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system
bus frequency for the processor. You may be able to change the settings in the system
Setup Utility. We strongly recommend that you do not over-clock processors or
other components to run faster than their rated speed.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from the
power outlet before installing or removing the motherboard or other
hardware components.
This motherboard has an LGA1155 socket. When choosing a processor, consider the
performance requirements of the system. Performance is based on the processor
design, the clock speed and system bus frequency of the processor, and the quantity
of internal cache memory and external cache memory.
Fail-Safe Procedures for Over-clocking
When end-users encounter failure after attempting over-clocking, please take the
following steps to recover from it.
1. Shut down the computer.
2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the
PC up.
3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.
4. The BIOS returns to the default setting by itself.
Installing the Motherboard
CPU Installation Procedure
The following illustration shows CPU installation components.
A. Disengaging of the Load Lever
· Hold the hook of lever and pull it to the
left side to clear retention tab.
· Rotate the load lever to fully open
position.
B. Opening of the Load Plate
· Put your thumb on the tail of the load
plate and press the tail down.
· Rotate the load plate to fully open
position.
C. Removing the Cap
· Be careful not to touch the contact at
any time.
D. Inserting the Package
· Grasp the package. Ensure to grasp
on the edge of the substrate.
· Make sure pin 1 indicator is on your
bottom-left side.
· Aim at the socket and place the
package carefully into the socket by
purely vertical motion.
11
E. Closing the Load Plate
· Rotate the load plate onto the package
IHS (Intergraded Heat Spreader).
· Engage the load lever while pressing
down lightly onto the load plate.
· Secure the load lever with the hook
under retention tab.
F. Fasten the cooling fan supporting base
onto the CPU socket on the motherboard.
G. Make sure the CPU fan is plugged to the
CPU fan connector. Please refer to the
CPU cooling fan user’s manual for more
detail installation procedure.
Installing the Motherboard
12
1. To achieve better airflow rates and heat dissipation, we suggest
that you use a high quality fan with 3800 rpm at least. CPU fan and
heatsink installation procedures may vary with the type of CPU fan/
heatsink supplied. The form and size of fan/heatsink may also vary.
2. DO NOT remove the CPU cap from the socket before installing a
CPU.
3. Return Material Authorization (RMA) requests will be accepted
only if the motherboard comes with the cap on the LGA1155 socket.
Installing Memory Modules
This motherboard accommodates two memory modules. It can support two 240-pin
DDR3
DDR3 1333/1066 SDRAM. The total memory capacity is 16 GB.
DDR3 SDRAM memory module table
Memory module Memory Bus
DDR3 1066 533 MHz
DDR3 1333 667 MHz
You must install at least one module in any of the two slots. Total memory capacity
is 16 GB.
Do not remove any memory module from its antistatic packaging
until you are ready to install it on the motherboard. Handle the
modules only by their edges. Do not touch the components or metal
parts. Always wear a grounding strap when you handle the modules.
Installing the Motherboard
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR3 SDRAM .
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install any remaining DIMM modules.
13
* For reference only
Installing the Motherboard
14
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect
them to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can
increase the motherboard’s capabilities by adding hardware that performs tasks that
are not part of the basic system.
PCIEX16 Slot
PCIE1~3 Slots
PCI1~2 Slots
Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.
The PCI Express x16 slot is used to install external PCI Express
graphics cards.
The PCI Express x1 slots are fully compliant to the PCI Express Base Specification revision 2.0.
This motherboard is equipped with two standard PCI slots. PCI
stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board
are PCI v2.2 compliant.
Installing the Motherboard
Follow these instructions to install an add-on card:
1 Remove a blanking plate from the system case corresponding to the
slot you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
* For reference only
15
1. For some add-on cards, for example graphics adapters and network
adapters, you have to install drivers and software before you can begin using
the add-on card.
2. The onboard PCI interface does not support 64-bit SCSI cards.
Installing the Motherboard
16
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional
devices:
F_AUDIO: Front Panel Audio header
This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.
Pin Signal Name Pin Signal Name
1 PORT 1L 2 AUD_GND
3 PORT 1R 4 PRESENCE#
5 PORT 2R 6 SENSE1_RETURN
7 SENSE_SEND 8 KEY
9 PORT 2L 10 SENSE2_RETURN
SATA1~4: Serial ATAII connectors
These connectors are used to support the Serial ATA 3Gb/s devices, simpler disk drive
cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA
interface. But maintains register compatibility and software compatibility with Parallel ATA.
Pin Signal Name
1 Ground 2 TX+
3 TX- 4 Ground
5 RX- 6 RX+
7 Ground - -
Pin Signal Name
Installing the Motherboard
F_USB1~2(USB 2.0): Front Panel USB 2.0 headers
The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Additionally, some computer cases have USB 2.0 ports at the front of the case. If you have
this kind of case, use auxiliary USB 2.0 connector to connect the front-mounted
ports to the motherboard.
Unlike F_USB1 in this mainboard, F_USB2 supports EZ Charger technology, provides about 1A current than general USB port in off mode for USB devices. It is useful
and excellent, especially for the iPhone, iPad and iPod touch devices that need a
large amount of current for faster recharging within less time.
Pin Signal Name Function
1 USBPWR Front Panel USB Power
2 USBPWR Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground
9 Key No pin
10 USB_FP_OC0 N/A
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or system
hang-up.
17
CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis
equipped with instrusion detection switch and needs to be enabled in BIOS.
Pin 1-2 Function
Short Chassis cover is removed
Open Chassis cover is closed
ME_UNLOCK: ME Unlock Header
Pin 1-2 Function
Short Unlock
Open Lock
Installing the Motherboard
18
SPDIFO: SPDIF out header
This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface)
output to digital multimedia device through optical fiber or coaxial connector.
Pin Signal Name
1 SPDIFOUT
2 +5V
3 Key
4 GND
COM: Onboard serial port header
Connect a serial port extension bracket to this header to add a serial port to your
system.
Pin Signal Name Function
1 DCDB Data Carrier Detect
2 SINB Serial Input
3 SOUTB UART B Serial Output
4 DTRB UART B Data Terminal Ready
5 GND Ground
6 DSRB Data Set Ready
7 RTSB RART B Request to Send
8 CTSB Clear to Send
9 RI Ring Indicator
10 Key No pin
LPT: Onboard parallel port Header
This is a header that can be used to connect to the printer, scanner or other devices.
Pin Signal Name Pin Signal Name
1 STROBE 14 AFD
2 PD0 15 ERROR
3 PD1 16 INIT
4 PD2 17 SLCT
5 PD3 18 Ground
6 PD4 19 Ground
7 PD5 20 Ground
8 PD6 21 Ground
9 PD7 22 Ground
10 ACK 23 Ground
11 BUSK 24 Ground
12 PE 25 Ground
13 SLCT 26 Key
Installing the Motherboard
Installing a SATA Hard Drive
This section describes how to install SATA devices such as a hard disk drive and a CDROM drive.
About SATA Connectors
Your motherboard features four SATA 3.0 Gb/s connectors supporting a total of four
drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the SATA hard drives which are currently used in most PCs. These
connectors are well designed and will only fit in one orientation. Locate the SATA
connectors on the motherboard and follow the illustration below to install the SATA
hard drives.
Installing Serial ATA Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the
Serial ATA protocol. You can connect either end of the SATA cable to the SATA hard
drive or the connector on the motherboard.
19
SATA cable
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard.
2 Attach the other cable end to the SATA hard drive.
3 Attach the SATA power cable to the SATA hard drive and connect the
other end to the power supply.
* For reference only
This motherboard supports the “Hot-Plug” function.
(optional)
SATA power cable (optional)
Installing the Motherboard
Loading...