ECS H110M-C3V, H110M-C3D User Manual

H110M-C3V/H110M-C3D

USER MANUAL

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Windows® 7/8 are registered trademarks of Microsoft Corp.

Other product names used in this manual are the properties of their respective owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

H110M-C3V/H110M-C3D

USER MANUAL

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference

that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

The manual consists of the following:

Describes features of the motherboard.



page 1

Describes installation of motherboard components.



page 9



page 29



page 61

Installing the Motherboard

Introducing the Motherboard

Provides information on using the BIOS Setup Utility.

Describes the motherboard software.

Limits and methods of mesurement of radio disturbance characteristics of information technology equipment

EN 55022

EN 61000-3-2

Disturbances in supply systems caused

EN 61000-3-3

Disturbances in supply systems caused by household appliances and similar electrical equipment “ Voltage fluctuations”

EN 55024

Information technology equipment-Immunity characteristicsLimits and methods of measurement

EN 60950

Safety for information technology equipment including electrical business equipment

CE marking

About the Manual



This device is in conformity with the following EC/EMC directives:

Chapter 4

Chapter 1

Chapter 2

Chapter 3 Using BIOS

Using the Motherboard Software

Chapter 5 Trouble Shooting

Provides basic trouble shooting tips.

page 67



iii

H110M-C3V/H110M-C3D USER MANUAL

Chapter 2 9

Installing the Motherboard 9

Safety Precautions.............................................................................9

Installing the Motherboard in a Chassis......................................9

Checking Jumper Settings...............................................................10

Installing Hardware.................................................................11

Installing the Processor...........................................................11

Installing the CPU Cooler.........................................................13

Installing Memory Modules....................................................14

Installing Add-on Cards...........................................................15

Connecting Optional Devices..................................................17

Installing a SATA Hard Drive...................................................23

Connecting Case Components.......................................................24

Front Panel Header.................................................................26

TABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction...................................................................................1

Pakage Contents............................................................................1

Specifications................................................................................2

Motherboard Components..........................................................4

I/O Ports..............................................................................................7

Chapter 3 29

Using BIOS 29

About the Setup Utility................................................................29

The Standard Configuration....................................................29

Entering the Setup Utility........................................................29

Resetting the Default CMOS Values.....................................30

Using BIOS........................................................................................31

BIOS Navigation Keys..............................................................31

Main Menu.............................................................................33

Advanced Menu......................................................................34

Chipset Menu..........................................................................45

Tweak Menu............................................................................52

Security Menu..........................................................................57

Boot Menu...............................................................................58

Exit Menu................................................................................59

H110M-C3V/H110M-C3D

USER MANUAL

Chapter 4 61

Using the Motherboard Software 61

Auto-installing under Windows 7/8..............................................61

Running Setup.........................................................................62

Manual Installation..........................................................................64

ECS Utility Software (Intelligent EZ Utility).....................................64

Chapter 6 67

Trouble Shooting 67

Start up problems during assembly..............................................67

Start up problems after prolong use............................................68

Maintenance and care tips..............................................................68

Basic Troubleshooting Flowchart...................................................69

H110M-C3V/H110M-C3D

USER MANUAL

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the H110M-C3V/H110M-C3D motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1151 socket for Intel® Skylake processor.

This motherboard is based on Intel

H110 Express Chipset for best desktop platform solution. It supports up to 32 GB of system memory with dual channel DDR3L 1600 MHz. One PCI Express x16 Gen3 slot is supported, intended for Graphics Interface. In addition, one PCI Express x1 Gen2 slot is for extending usage.

It integrates USB 2.0 and USB 3.0 interface, supporting up to six USB 2.0 ports (two USB 2.0 ports at rear panel and two USB 2.0 headers support additional four USB 2.0 ports) and four USB 3.0 ports (two USB 3.0 ports at the rear panel and one USB 3.0 header supports additional two USB 3.0 ports).

The motherboard is equipped with advanced full set of I/O ports in the rear panel, including one PS/2 mouse and PS/2 keyboard connector, one DVI port (or one HDMI port), one VGA port, two USB 3.0 ports, two USB 2.0 ports, one RJ45 LAN connector, and audio jacks for line-in, line-out and microphone.

In addition, this motherboard supports four SATA 6Gb/s connectors for expansion.

Your motherboard package ships with the following items:

Package Contents

H110M-C3V/H110M-C3D Motherboard User Manual DVD I/O Shield 2 SATA 6G Cables

    

The package contents above are for reference only, please take the actual package items as standard.

Chapter 1

H110M-C3V/H110M-C3D

USER MANUAL

CPU

Specifications

• Intel® H110 Chipset

Chipset

• Supported by Intel® H110 Express Chipset

- 4 x Serial ATA 6Gb/s devices

Storage

• LGA1151 socket for Intel® Skylake processor

• Supports CPU up to 95W, TDP up to 95W

Note: Please go to ECS website for the latest CPU support list.

• 1 x PS/2 mouse & PS/2 keyboard connector

• 1 x HDMI port (or 1 x DVI port)

• 1 x D-sub port (VGA port)

• 2 x USB 2.0 ports

• 2 x USB 3.0 ports

• 1 x RJ45 LAN connector

• 1 x Audio 6-ch jacks (line-in, line-out, microphone)

Rear Panel I/O

LAN

• Realtek RTL8111H Gigabit Lan

• Realtek ALC662-VDD-GR 6-CH High Definition audio CODEC

- Compliant with HD audio specification

Audio

Internal I/O Connectors & Headers

• 1 x 24-pin ATX Power Supply connector

• 1 x 4-pin ATX 12V Power connector

• 1 x 4-pin CPU_FAN connector

• 1 x 4-pin SYS_FAN connector

• 1 x USB 3.0 header supports additional two USB 3.0 ports

• 2 x USB 2.0 headers support additional four USB 2.0 ports

• 4 x SATA 6Gb/s connectors

• 1 x Front Panel audio header

• 1 x Front Panel switch/LED header

• 1 x COM header

• 1 x Clear CMOS jumper

• 1 x IDEA Memory jumper

• 1 x Trusted platform module header (TPM)

• 1 x Buzzer header

• 1 x Case open header

• 1 x ME unlock header

Expansion Slots

• 1 x PCI Express x16 Gen3 slot

• 1 x PCI Express x1 Gen2 slot

• Dual-channel DDR3L memory architecture

• 2 x 240-pin DDR3L DIMM sockets support up to 32 GB

Memory

Note: Please go to ECS website for the latest Memory support list.

H110M-C3V/H110M-C3D

USER MANUAL

Chapter 1

• AMI BIOS with 64Mb SPI Flash ROM

• Supports Plug and Play, STR (S3)/ STD (S4), Hardware Monitor

• Audio, LAN, can be disabled in BIOS

• F7 hot key for boot up devices option

• Supports ACPI & DMI

• Supports PgUp clear CMOS Hotkey (PS2 KB Model only)

• Add the function of copying BIOS parameters to USB flash drive

System BIOS

• Micro ATX Size, 225mm x 170mmForm Factor

• Supports eBLU*1/eDLU/eSF*1/Cyberlink Media Suite*

AP Support

Note: *1Microsoft .NET Framework 3.5 is required.

*2Free bundle software including ECS DVD: Cyberlink Media

Suite.

Chapter 1

H110M-C3V/H110M-C3D

USER MANUAL

Motherboard Components

H110M-C3V

H110M-C3V/H110M-C3D

USER MANUAL

Chapter 1

H110M-C3D

Chapter 1

H110M-C3V/H110M-C3D

USER MANUAL

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket

LGA1151 socket for Intel

Skylake processor

2. CPU_FAN 4-pin CPU cooling fan connector

3. IDEA_MEMORY IDEA Memory jumper

4. DIMM1~2 240-pin DDR3L Module slots

5. ATX_POWER Standard 24-pin ATX power connector

6. SATA1~4 Serial ATA 6Gb/s connectors

7. F_PANEL Front panel switch/LED header

8. TPM Trusted platform module header

9. ME_UNLOCK ME unlock header

10. F_USB1~2 Front panel USB 2.0 headers

11. COM Onboard serial port header

12. F_AUDIO Front panel audio header

13. CASE CASE open header

14. BZ Buzzer header

15. PCIEX1 PCI Express Gen2 x1 slot

16. USB3F Front panel USB 3.0 header

17. PCIEX16 PCI Express x16 slot Gen3 for graphics interface

18. SYS_FAN 4-pin system cooling fan connector

19. CLR_CMOS Clear CMOS jumper

20. ATX_12V 4-pin +12V power connector

H110M-C3V/H110M-C3D

USER MANUAL

Chapter 1

I/O Ports

1. PS/2 Mouse (green)

Use the upper PS/2 port to connect the PS/2 Mouse.

2. PS/2 Keyboard (purple) Use the upper PS/2 port to connect the PS/2 Keyboard.

3. DVI Port or HDMI Port

You can connect the display device to the DVI port or the HDMI port.

4. VGA Port

Connect your monitor to the VGA port.

5. USB 3.0 Ports

Use the USB 3.0 ports to connect USB 3.0 devices.

6. LAN Port

Connect an RJ-45 jack to the LAN port to connect your computer to the Network.

7. USB 2.0 Ports

Use the USB 2.0 ports to connect USB 2.0 devices.

8. Line-in (blue) It can be connected to an external CD/DVD player, Tape player or other audio devices for audio input.

LAN LED Status Description

OFF No dat a Orange blinking Active OFF No link Green Link

Activity LED

Link LED

LAN Port

Chapter 1

H110M-C3V/H110M-C3D

USER MANUAL

9. Line-out (lime) It is used to connect to speakers or headphones.

10.Microphone (pink) It is used to connect to a microphone.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

Chapter 2

Installing the Motherboard

2-1. Safety Precautions

2-2. Installing the motherboard in a Chassis

This motherboard carries a Micro ATX form factor of 225 x 170 mm. Choose a chassis that accommodates this from factor. Make sure that the I/O template in the chassis matches the I/O ports installed on the rear edge of the motherboard. Most system chassis have mounting brackets installed in the chassis, which corresponds to the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Follow these safety precautions when installing the motherboard:

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity.

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard.

• Leave components in the static-proof bags.

• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

Do not over-tighten the screws as this can stress the motherboard.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”.

2-3. Checking Jumper Settings

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2-4. Installing Hardware

2-4-1. Installing the Processor

• This motherboard has an LGA1151 socket.

• When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

• You may be able to change the settings in the system Setup Utility. We strongly recommend you do not over-clock processor or other components to run faster than their rated speed.

• The following illustration shows CPU installation components.

A. Press the hook of lever down with your thumb and pull it to the right side to release it from retention tab.

B. Lift the tail of the load lever and rotate the load plate to fully open position.

C. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

D. Rotate the load plate onto the package IHS (Intergraded Heat Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically.

Please save and replace the cover onto the CPU socket if processor is removed.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

A. Apply some thermal grease onto the contacted area between the heatsink and the CPU, and make it to be a thin layer.

B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector.

C. Connect the CPU cooler power connector to the CPU_FAN connector.

2-4-2. Installing the CPU Cooler

• Install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

• Avoid using cooling fans with sharp edges in case the fan casing and the clips cause serious damage to the motherboard or its components.

• To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heat sink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.

• DO NOT remove the CPU cap from the socket before installing a CPU.

• Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with the cap on the LGA1151 socket.

• The following illustration shows how to install CPU fan.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2-4-3. Installing Memory Modules

• This motherboard accommodates two memory modules. It can support two 240-pin DDR3L 1600 MHz.

• Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

• You must install at least one module in any of the four slots. Total memory capacity is 32 GB.

• Refer to the following to install the memory modules.

C. The slot latches are levered upwards and latch on to the edges of the

DIMM.

A. Push the latches on each side of the DIMM slot down.

B. Install the DIMM module into the slot and press it firmly down until it

seats c

orrectly. Check that the cutouts on the DIMM module edge

connector match the notches in the DIMM slot.

We suggest users not to mix memory type. It is recommended to use the same brand and type memory on this motherboard.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2-4-4. Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

The PCI Express x1 slot is fully compliant to the PCI Express Base Specification revision 2.0.

PCIEX1

PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI

Express graphics card that is fully compliant to the PCI Express Base Specification revision 3.0.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

Install the VGA Card in the PCIE X16 slot

1 Remove a blanking plate from the system case corresponding to the slot

you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

Follow these instructions to install an add-on card:

Please refer the following illustrations to install the add-on card:

Install the LAN Card in the PCIEX1 slot

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2-4-5. Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

No. Components No. Components

1 SATA1~4 5 COM

2TPM6F_AUDIO

3ME_UNLOCK 7 CASE

4 F_USB1~2 8 USB3F

SATA1~4 connectors are used to support the Serial ATA 6Gb/s device, simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

1. SATA1~4: Serial ATA III Connectors

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2. TPM: Trusted Platform Module Header

Trusted platform module (TPM) is a published specification detailing a microcontroller that can store secured information, and implementations of that specification.

3. ME_UNLOCK: ME Unlock Header

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

The motherboard has two USB 2.0 headers supporting four USB 2.0 ports. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

4. F_USB1~2: Front Panel USB 2.0 headers

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.

5. COM: Onboard Serial Port Header

Connect a serial port extension bracket to this header to add a serial port to your system.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

If you use AC’ 97 Front Panel, please tick off the option of “Disabled Front Panel Detect ”. If you use HD Audio Front Panel, please don’ t tick off “Disabled Front Panel Detect ” .

* For reference only

AC’ 97 Audio Configuration: To enable the front panel audio connector to support AC97 Audio mode.

The front panel audio header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC’ 97 front panel audio to HD onboard headers, please set as below picture.

6. F_AUDIO: Front Panel Audio Header

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

If you use AC’ 97 Front Panel, please don’ t tick off “Using Front Jack Detect ”. If you use HD Audio Front Panel, please tick off the option of “ Using Front Jack Detect ” .

* For reference only

7. CASE: Chassis Intrusion Detect Header

This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.

This Motherboard implements one USB 3.0 header supporting 2 extra front USB 3.0 ports, which delivers 5Gb/s transfer rate.

8. USB3F: Front Panel USB 3.0 Header

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2-4-6. Installing a SATA Hard Drive

About SATA Connectors

Your motherboard features four SATA connectors supporting a total of four drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with a SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

* For reference only

Installing Serial ATA Hard Drives

This section describes how to install a SATA Hard Drive.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

No. Components No. Components

1CPU_FAN4 BZ

2 ATX_POWER 5 SYS_FAN

3 F_PANEL 6 ATX12V

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

2-4-7. Connecting Case Components

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

2. ATX_POWER (ATX 24-pin Power Connector) & 6. ATX12V (ATX 12V Power Connector)

Connect the standard power supply connector to ATX_POWER. Connect the auxiliary case power supply connector to ATX12V.

1. CPU_FAN (CPU cooling FAN Connector) & 5. SYS_FAN (System Cooling FAN Connector)

Connect the CPU cooling fan cable to CPU_FAN.

Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V.

Connect the system cooling fan connector to SYS_FAN.

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

3. F_PANEL: Front Panel Header

The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:

The ATX 24-pin connector allows you to connect to ATX_POWER power supply.

With ATX_POWER power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX_POWER match perfectly.

Connecting 24-pin power cable

24-pin power cable

The ATX12V power connector is used to provide power to the CPU.

When installing 4-pin power cable, the latches of power cable and the ATX12V match perfectly.

Connecting 4-pin power cable

4-pin power cable

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

This concludes Chapter 2. The next chapter covers the BIOS.

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

4. BZ: Buzzer Header

Chapter 2

H110M-C3V/H110M-C3D USER MANUAL

Memo

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

About the Setup Utility

The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Press DEL to enter SETUP

Chapter 3

Using BIOS

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Press the delete key to access BIOS Setup Utility.

Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.

Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

The default BIOS setting for this motherboard apply for most conditions with optimum performance. We do not suggest users change the default values in the BIOS setup and take no responsibility to any damage caused by changing the BIOS settings.

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

 Scrolls through the items on a menu

+/-

Change Opt.

F2 Previous Value F3 Optimized Defaults

F1 General Help

ESC Exits the current menu



Enter Select

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by an icon .

F4 Save & Exit

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with an icon ) lead to submenus that enable you to change the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

1. For the purpose of better product maintenance, the manufacture

reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.

2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select

item; Double click: enter; Right click: exit.

Select the default icon and press <Enter> or double click the left key of the mouse to display the screen. Then you can load optimized defaults or not.

Default

Select the advanced icon and press <Enter> or double click the left key of the mouse to display the screen.

Advanced

Select the exit icon and press <Enter> or double click the left key of the mouse to display the screen.

Exit

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Main Menu

System Date & Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.

System Language (English)

This item is used to set system language.

This menu shows the information of BIOS and enables you to set the system language, date and time.

Choose the system default language

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

BIOS Information System Language English

System Date Tue 07/14/2015

System Time 00:01:42

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

The Advanced menu items allow you to change the settings for the CPU and other system.

Advanced Menu

LAN Configuration Parameters

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

LAN Configuration

PC Health Status Power Management Setup ACPI Settings CPU Configuration SAT A Configuration USB Configuration Super IO Configuration Trusted Computing

LAN Configuration

The item in the menu shows the LAN-related information that the BIOS automatically detects.

Onboard LAN Controller (Enabled)

Use this item to enable or disable Onboard LAN controller.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

LAN Configuration

Onboard LAN Controller Enabled

Enabled/Disabled Onboard LAN Controller

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

PC Health Status

On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.

Scroll to this item and press <Enter> to view the following screen:

 Smart Fan Function

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU T emperature (DTS) 3 9 System T emperature 33 O C CPU Fan Speed 3000 RPM System Fan Speed 0 RPM Core Voltage 1.012V DIMM Voltage 1.364V +12V 12.012V +5VSB 5.027V +VCC 5.082V

TCC Activation Temperature (DTS) 10 0

Smart Fan Function

PC Health Status

Smart Fan Select

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Smart Fan Select CPU Fan

Smart Fan Mode Normal Smart Fan start PWM value 180

Smart Fan start PWM TEMP (DTS) 70 DeltaT 3 Smart Fan Slope PWM value 10 Fan Full Speed Offset (DTS) 7 7

Smart Fan Select (CPU Fan)

This item allows you to change and configure Smart Fans on M/B. ex. CPU Fan, System Fan.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Smart Fan Mode (Normal)

This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.

Smart Fan start PWM value (180)

Smart Fan start PWM TEMP (DTS) (70)

This item is used to set the start PWM value of the smart fan.

This item is used to set the start temperature of the smart fan.

DeltaT (3)

This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.

Smart Fan Slope PWM value (10)

This item is used to set the Slope Select PWM of the smart fan.

This item is used to set the fan full speed offset value.

Fan Full Speed Offset (DTS) (77)

Press <Esc> to return to the PC Health Status page.

• CPU Temperature (DTS)

• System Temperature

• CPU Fan Speed

• System Fan Speed

• Core Voltage

• DIMM Voltage

• +12V

• +5VSB

• +VCC

System Component Characteristics

These items display the monitoring of the overall inboard hardware health events, such as CPU & DIMM voltage, CPU & System fan speed...etc.

Press <Esc> to return to the Advanced Menu page.

TCC Activation Temperature (DTS) (100)

This item is used to set the value from the factory TCC activation temperature.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Power Management Setup

This page sets up some parameters for system power management operation.

Resume By PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI/PCI-E Modem or PCI/PCI-E LAN c

ard. You must use an ATX power supply in order to use this

feature. Use this item to do wake-up action if inserting the PCI/PCI-E card.

Resume By USB (Disabled)

This item allows you to enable or disable the USB device wakeup function from S3 mode.

EUP Function (Enabled)

This item allows user to enable or disable EUP support.

Press <Esc> to return to the Advanced Menu page.

Resume By RING (Disabled)

An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state.

Power LED Type (Dual Color LED)

This item shows the type of the Power LED.

Resume By PS2 MS (Disabled)

This item enables or disables you to allow mouse activity to awaken the system from power saving mode.

Resume By PS2 KB (Disabled)

This item enables or disables you to allow keyboard activity to awaken the system from power saving mode.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

About Resume by Ring

Power Management Setup

Resume By RING Disabled

Resume By PME Disabled Resume By USB Disabled Resume By PS2 KB Disabled Resume By PS2 MS Disabled Resume By RTC Alarm Disabled EUP Function Enabled Power LED Type Dual Color LED

Resume By RTC Alarm (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

ACPI Settings

The item in the menu shows the highest ACPI sleep state when the system enters suspend.

ACPI Sleep State [S3(Suspend to RAM)]

This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default).

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed.

ACPI Settings

ACPI Sleep State S3 (Suspend to RAM)

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

CPU Configuration

The item in the menu shows the CPU.

Intel(R) Core(TM) i5-6400K CPU @ 2.20GHz

This is display-only field and displays the information of the CPU installed in your computer.

EM64T (Supported)

This item shows the computer supports EM64T.

Processor Speed (2500MHz)

This item shows the current processor speed.

Processor Stepping (506E3)

This item shows the processor stepping version.

Microcode Revision (23)

This item shows the Microcode version.

Processor Cores (4)

This item shows the core number of the processor.

Intel HT Technology (Not Supported)

This item shows the computer not supports Intel HT Technology.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Number of cores to enable in each processor package.

CPU Configuration Intel(R) Core(TM) i5-6400K CPU @ 2.20GHz

EM64T Supported Processor Speed 2500 MHz Processor Stepping 506E3 Microcode Revision 2 3 Processor Cores 4 Intel HT Technology Not Supported Intel VT-x Technology Supported

Active Processor Cores All

Limit CPUID Maximum Disabled Execute Disable Bit Enabled Intel Virtualization T echnology Enabled Package C State limit AUTO Enhanced Halt (C1E) Enabled

Active Processor Cores (All)

Use this item to control the number of active processor cores.

Limit CPUID Maximum (Disabled)

Use this item to enable or disable the maximum CPUID value limit, you can enables this item to prevent the system from “rebooting” when trying to install Windows NT

4.0.

Intel VT-x Technology (Supported)

This item shows the computer supports Intel VT-x Technology.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Press <Esc> to return to the Advanced Menu page.

Execute Disable Bit (Enabled)

This item allows the processor to classify areas in memory by where application code can execute and where it cannot. When a malicious worm attempts to insert code in the buffer, the processor disables code execution, preventing damage or worm propagation. Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks, reducing the need for virus related repair.

Intel Virtualization Technology (Enabled)

When disabled, a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology.

Package C State limit (AUTO)

Use this item to set the package C state limit.

Enhanced Halt (C1E) (Enabled)

Use this item to enable or disable the Enhanced C1 state.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

SATA Configuration

Use this item to show the mode of serial SATA configuration options.

SATA Mode (AHCI)

Use this it

em to select SATA mode.

Press <Esc> to return to the Advanced Menu page.

SATA Port 1~4 (Not Present)

This motherboard supports four SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.

Spin up Device (Disabled)

On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device.

External SATA (Disabled)

Use this item to enable or disable External SATA Support.

Determines how SATA controller(s) operate.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

SAT A Configuration

SAT A Mode AHCI

SAT A Port1 Not Present Spin Up Device Disabled External SAT A Disabled

SAT A Port2 Not Present Spin Up Device Disabled External SAT A Disabled

SAT A Port3 Not Present Spin Up Device Disabled External SAT A Disabled

SAT A Port4 Not Present Spin Up Device Disabled External SAT A Disabled

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

All USB Devices (Enabled)

Use this item to enable or disable all USB devices.

USB Configuration

Use this item to show the information of USB configuration.

Legacy USB Support (Enabled)

Use this item to enable or disable support for legacy USB devices.

Press <Esc> to return to the Advanced Menu page.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

USB Support Parameters

USB Configuration

All USB Devices Enabled

Legacy USB Support Enabled

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Super IO Configuration

Use this item to show the information of Super IO configuration.

Super IO Chip (IT8613)

This item shows the information of the super IO chip.

Serial Port (Enabled)

This item allows you to enable or disable serial port.

Device Settings (IO=3F8h; IRQ=4)

This item shows the information of the device settings.

Change Settings (Auto)

Use this item to change device settings.

 Serial Port 1 Configuration

Scroll to this item and press <Enter> to view the following screen:

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Set Parameters of Serial Port 1 (COMA)

Super IO Configuration Super IO Chip IT8613

Serial Port 1 Configuration

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable or Disable Serial Port (COM)

Serial Port 1 Configuration

Serial Port Enabled

Device Settings IO=3F8h; IRQ=4; Change Settings Auto

Press <Esc> to return to the Super IO Configuration page.

Press <Esc> to return to the Advanced Menu page.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Trusted Computing

Use this item to show the information of trusted computing configuration.

Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available.

Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

TPM Support (Enabled)

Use this item to enable or disable the TPM support. O.S. will not show TPM. Reset of platform is required.

Configuration

TPM Support Enabled

Device Select Auto

Current Status Information No security Device Found

Press <Esc> to return to the Advanced Menu page.

Device Select (Auto)

TPM 1.2 will restrict support to TPM 1.2 devices, TPM 2.0 will restrict support to TPM 2.0 devices, Auto will support both with default set to TPM 2.0 devices if not found, TPM 1.2 devices will be enumerated.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

IGD Memory (64M)

This item shows the information of the IGD (Internal Graphics Device) memory.

The chipset menu items allow you to change the settings for the North Bridge chipset, South Bridge chipset and other system.

Chipset Menu

This item allows you to select graphics controller to use as the primary boot device.

DVMT Memory (256M)

When set to Fixed Mode, the graphics driver will reserve a fixed position of the s

ystem memory as graphics memory, according to system and graphics

requirements.

Initiate Graphic Adapter (Auto)



System Agent Configuration

Scroll to this item and press <Enter> to view the following screen:

System Agent (SA) Parameters.

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

System Agent Configuration

PCH Configuration ME Configuration

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select SG for Switchable Gfx.

System Agent Configuration

Initiate Graphic Adapter Auto

IGD Memory 64M DVMT Memory 256M IGD Multi-Monitor Disabled

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Multi-Monitor technology

Please note that Multi-Monitor technology supports up to four monitors: one or two Intel integrated Graphics and one or two PCI-Express graphics devices under Windows 7/8.

Multi-Monitor technology can help you to increase the area available for programs running on a single computer system through using multiple display devices.

It is not only to increase larger screen viewing but aslo to improving personal productivity.

Step 1. Insert ECS drives DVD to run Auto setup or browse the DVD to install Intel chipset drivers, VGA and sound drivers.(If you want know the detail information, please refer to chapter 4.)

Intel Integrated Graphics

PCI-Express Graphics

IGD Multi-Monitor (Disabled)

This item allows you to enable or disable the IGD Multi-Monitor.

Press <Esc> to return to the Chipset Menu page.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Step 2. Install all the drivers of PCI-Express graphic cards. Click the Browse CD item, then appears the following screen. Select the driver you want to install(e.g NVIDIA GeForce 8400 GS(Microsoft Corporation-WDDM v1.1)) and double click it.

Step 3. Enable IGD Multi-Monitor from BIOS. In the following BIOS screen, please set IGD Multi-Monitor to [Enabled].

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select which of IGFX/PEG/PCI Graphics device should be Primary Display or select SG for Switchable Gfx.

System Agent Configuration

Initiate Graphic Adapter Auto

IGD Memory 64M DVMT Memory 256M IGD Multi-Monitor Disabled

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Step 4. Change the appearance of your displays under Windows 7/8.

Change the apprearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

1. DELL U2410Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Extend desktop to this displayMultiple displays:

This is currently your main display.

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

Show the path of the setting location

Display devices

The type of the display

Set the multiple displays

1. Enter the Control Panel menu, select the Display in the All Control Panel Items and click the Screen Resolution, then appears the following screen.

2.Select display devices, set the multiple displays option and to extend destop for display “Multi-Monitor technology”.

Change the apprearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

3. DELL U2410Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Disconnect this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

Y ou must select Apply before making additional changes.

Extend desktop to this display

Disconnect this display

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Change the apprearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

4. AL1717Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Disconnect this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

Y ou must select Apply before making additional changes.

Change the apprearance of your displays

Control Panel All Control Panel Items Display Screen Resolution

Search Control Panel

Detect

Identify

4. AL1717Display:

Resolution:

1920 x 1200 (recommended)

Orientation: Landscape

Extend desktop to this displayMultiple displays:

Make this my main display

Advance settings

Make text and other items larger or smaller What display settings should I choose?

OK Cancel Apply

Y ou must select Apply before making additional changes.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

PCH Configuration

Scroll to this item and press <Enter> to view the following screen:

Restore AC Power Loss (Power Off)

This item enables your computer to automatically restart or return to its operating status.

Azalia HD Audio (Enabled)

This item enables or disables Azalia HD audio.

Case Open Warning (Disabled)

This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case.

Chassis Opened (No)

This item indicates whether the case has been opened.

Press <Esc> to return to the Chipset Menu page.

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Select AC power state when power is re-applied after a power failure.

PCH Configuration

Restore AC Power Loss Power Off

Audio Configuration Azalia HD Audio Enabled

Case Open Warning Disabled Chassis Opened No

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

 ME Configuration

Scroll to this item and press <Enter> to view the following screen:

ME Control (Enabled)

Use this item to enable or disable the ME Firmware.

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Enable/Disable ME Firmware

ME FW Version (11.0.0.1136)

This item shows the ME FW version.

Press <Esc> to return to the Chipset Menu page.

Management Engine T echnology Configuration

ME Control Enabled

TPM Device Selection dTPM 1.2 ME FW Version 1 1.0.0.1 136

TPM Device Selection (dTPM 1.2)

Use this item to select TPM device: PTT or dTPM. PTT-Enables PTT in SkuMgr. dTPM

1.2-Disables PTT in SkuMgr Warning! PTT/dTPM will be disabled and all data saved on it will be lost.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

+/- : Change Opt.

Enter/Dbl Click : Select



: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults

ESC/Right Click: Exit

F4: Save & Exit



Main Advanced Chipset Tweak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

CPU OverClocking Configuration

Tweak

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

Tweak Menu

Intel(R) Core(TM) i5-6400T CPU @ 2.20GHz Processor Speed 2500 MHz Memory Frequency 1067 MHz T otal Memory 1024 MB

CPU OverClocking Configuration

Memory Configuration Spread Spectrum Auto

EIST (Enabled)

This item allows users to enable or disable the EIST (Enhanced Intel SpeedStep Technology).

Turbo Boost (Enabled)

This item allows you to enable or disable turbo boost.

Main Advanced Chipset Tweak Security Boot Exit

Enhanced Intel SpeedStep T echnology

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

EIST Enabled

Turbo Boost Enabled Power Limit 3 Settings Power Limit 4 Settings Performance Mode Boost TDP Lock Disabled

Core Ratio 22 Core 1 Ratio Limit 28 Core 2 Ratio Limit 27 Core 3 Ratio Limit 25 Core 4 Ratio Limit 25

 CPU OverClocking Configuration

Scroll to this item to view the following screen:

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Main Advanced Chipset Tweak Security Boot Exit

Enable/Disable Limit 3 override. If this option is disabled, BIOS will leave the default values for Power Limit 3 and Power Limit 3 Time Window.

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Power Limit 3 Settings Power Limit 3 Override Disabled

 Power Limit 3 Settings

Scroll to this item to view the following screen:

Power Limit 3 Override (Disabled)

Use this item to enable or disable the limit 3 override. If this option is disabled, BIOS will leave the default values for power limit 3 and power limit 3 time window.

Press <Esc> to return to the CPU OverClocking Configuration page.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Main Advanced Chipset Tweak Security Boot Exit

Enable/Disable Limit 4 override. If this option is disabled, BIOS will leave the default values for Power Limit 4 and Power Limit 4 Time Window.

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Power Limit 4 Settings Power Limit 4 Override Disabled

 Power Limit 4 Settings

Scroll to this item to view the following screen:

Power Limit 4 Override (Disabled)

Use this item to enable or disable the limit 4 override. If this option is disabled, BIOS will leave the default values for power limit 4 and power limit 4 time window.

Press <Esc> to return to the CPU OverClocking Configuration page.

Press <Esc> to return to the Tweak Menu page.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Main Advanced Chipset Tweak Security Boot Exit

The selection of Memory Profiles which impacts memory sizing behavior.

Press <Esc> to return to the Tweak Menu page.

Memory Configuration

Scroll to this item to view the following screen:

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Memory Frequency (1067)

This item shows the information of the memory frequency.

Memory Profiles (Automatic)

This item enables you to set the memory profiles. The selection of memory profiles

impacts memory sizing beha

vior.

Memory Information

Memory Profiles Automatic

Memory Frequency 1067 Timing Default Current Target

Command Rate 0 2 1 tCL 16 16 7 tRCD 1 6 1 6 7 tRP 16 16 7 tRCD/tRP 16 16 7 tRAS 39 39 20 tRFC 19 3 19 3 59 tRFC2 193 193 0 tRFC4 133 133 0 tWR 18 18 8 tWTR_L 9 9 0 tWTR_S 3 3 0 tRRD_L 6 6 0 tRRD_S 4 4 0 tRTP 9 9 4 tFAW 28 28 20 tCWL 16 16 7

tCKE 0 6 0 tRDRD_dr 0 6 0 tRDRD_dd 0 7 0 tWRWR_dr 0 7 0 tWRWR_dd 0 7 0 tWRRD_dr 0 7 0 tWRRD_dd 0 7 0 tRDWR_dr 0 9 0 tRDWR_dd 0 10 0

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Processor Speed (2500 MHz)

This item shows the CPU speed.

Memory Frequency (1067 MHz)

This item shows the memory frequency.

Total Memory (1024 MB)

This item shows the total memory.

Intel(R) Core(TM) i5-6400T CPU @ 2.20GHz

This is display-only field and displays the information of the CPU installed in your comput

er.

Spread Spectrum (Auto)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

This page enables you to set setup administrator password and user password.

Security Menu

Administrator Password Status (Not Install)

This item shows administrator password installed or not.

User Password Status (Not Install)

This item shows user password installed or not.

Secure Boot (Disabled)

This item is used to control the secure boot flow, it is possible only if system runs in User Mode.

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Set Administrator Password

System Mode state (Setup)

This item shows system mode setup or not.

Secure Boot state (Not Active)

This item allows you to enable or disable the secure boot state.

Administrator Password

Administrator Password Status Not Install User Password Status Not Install

System Mode state Setup Secure Boot state Not Active

Secure Boot Disabled

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Main Advanced Chipset T weak Security Boot Exit

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

This page enables you to set the keyboard NumLock state.

Boot Menu

Operation System Select (Windows 7 or other OS)

This item is used to select the operation system.

Launch PXE OpROM (Disabled)

The item enables or disables launch PXE Option ROM.

Launch Storage OpROM (Enabled)

Use this item to enable or disable the Storage OpROM.

Fast Boot (Disabled)

This item enables or disables boot with initialization of a minimal set of device required to launch active boot option. Has no effect for BBS boot options.

Bootup NumLock State (On)

This item enables you to select NumLock state.

Quiet Boot (Enabled)

This item enables or disables quiet boot.

Update System BIOS (Enabled)

This item enables or disables update system BIOS.

Boot mode select (LEGACY)

Use this item to select boot mode.

Boot Option #1 /

2 /3 /4 /5 /6 /7 /8

These items show the boot priorities.

Windows 7 or other OS: Boot policy for Legacy OS.

Windows 8: Boot policy for UEFI OS without Compatibility Support Module(CSM).

Manual: User customized CSM parameters & boot policy.

Boot Configuration

Operation System select Windows 7 or other OS

Launch PXE OpROM Disabled Launch Strorage OpROM Enabled

Fast Boot Disabled Bootup NumLock State On

Quiet Boot Enabled Update System BIOS Disabled Boot mode select LEGACY

FIXED BOOT ORDER Priorities Boot Option #1 Hard Disk Boot Option #2 CD/DVD Boot Option #3 USB Hard Disk Boot Option #4 USB CD/DVD Boot Option #5 USB Key: Silicon-Pow... Boot Option #6 USB Floppy Boot Option #7 USB Lan Boot Option #8 Network

USB Flash Drive Priorities

This item enables you to specify the sequence of loading the operating system. Press <Enter> to see the submenu.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Boot Override

Use this item to select the boot device.

Save Options

This item enables you to save the options that you have made.

Save Changes

This item enables you to save the changes that you have made.

Discard Changes

This item enables you to discard any changes that you have made.

Restore Defaults

This item enables you to restore defaults to all the setup options.

Discard Changes and Exit

This item enables you to exit system setup without saving any changes.

Discard Changes and Reset

This item enables you to reset system setup without saving any changes.

This page enables you to exit system setup after saving or without saving the changes.

Exit Menu

Save Changes and Exit

This item enables you to exit

t the system setup after saving the changes.

Save Changes and Reset

This item enables you to reset system setup after saving the changes.

Main Advanced Chipset T weak Security Boot Exit

Go back to EZ Mode

Back to EZ Mode

Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset

Save Options Save Changes Discard Changes

Restore Defaults Save as User Defaults Restore User Defaults

Boot Override Silicon-Power PMAP

+/- : Change Opt.

Enter/Dbl Click : Select





: Select Screen

/Click: Select Item

F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit

Back to EZ Mode

This item enables you to back to EZ mode.

Save as User Defaults

This item enables you to save the changes that you have made as user defaults.

Restore User Defaults

This item enables you to restore the user defaults.

Chapter 3

H110M-C3V/H110M-C3D USER MANUAL

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Website. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

1 If your motherboard has a BIOS protection jumper, change the setting to

allow BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Ad-

vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)

3 Prepare a bootable device or create a bootable system disk. (Refer to

Windows online help for information on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s

Web site. Copy these files to the bootable device.

5 Turn off your computer and insert the bootable device in your computer.

(You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)

6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file

name of the new BIOS and then press <Enter>. Example: AFUDOS.EXE

040706.ROM

7 When the installation is complete, remove the bootable device from the

computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

Using the Motherboard Software

The auto-install DVD-ROM makes it easy for you to install the drivers and software. The support software DVD-ROM disc loads automatically under Windows 7/8. When you insert the DVD-ROM disc in the DVD-ROM drive, the auto-run feature will automatically bring up the installation screen. The screen has four buttons on it: Setup,

Utilities, Browse CD and Exit.

Auto-installing under Windows 7/8

Displays the path for all software and drivers available on the disk.

Open Windows Explorer and show the contents of the support disk.

Click “Exit” button to close the Auto-Setup

window.

Browse CD:

Click the “Setup” button to select and run the software installation program.

Click the “ Utilities” button to select and install ECS Intelligent Utility.

Information:

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

Follow these instructions to install device drivers and software for the motherboard:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

1. Click Setup. The installation program begins:

Running Setup

The motherboard identification is located in the upper left-hand corner.

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

5. Follow the instructions on the screen to install the items.

4. Click Next to run the Installation Wizard. An item installation screen appears:

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver.

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

If the auto-install DVD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Look

for the chipset and motherboard model, and then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

Manual Installation

ECS Utility Software (Intelligent EZ Utility)

ECS Intelligent EZ Utility provides friendly interfaces under Windows O.S, which makes your computing more easily and conveniently.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software.

Windows 7/8 will appear below UAC (User Account Control) message after the system restart. You must select “Yes” to install the next driver. Continue

this process to complete the drivers installation.

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

eBLU

ECS eBLU utility makes BIOS update faster and easier. eBLU will list the latest BIOS with a default check-mark. Click”install” button to install.

eDLU

ECS eDLU utility makes updating drivers fast and easy. eDLU saves time and hassle by listing all the latest drivers online. Just select the one you prefer and start to download and install the drivers.

eSF

eSF(Smart Fan) utility provides easy and safe way to adjust fan speed in accordance with your PC’s system loading and temperature.

It has five modes to adjust fan speed in a safe range without entering the BIOS to optimize your system cooling environment.

Microsoft .NET Framework 3.5 is required.

H110M-C3V/H110M-C3D USER MANUAL

Chapter 4

Memo

H110M-C3V/H110M-C3D USER MANUAL

Chapter 5

Trouble Shooting

Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. You may also log onto our ECS website for more information:

a) System does not power up and the fans are not running.

1. Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Make sure the power cord is plugged into the wall socket & the switch on the Power Supply Unit (PSU) is turned “ on “ as well. Turn on again to see if the CPU and power supply fans are running.

2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.

3. Check the CPU FAN connector is connected to the motherboard.

4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.

5. Check the 12V power connector is connected to the motherboard.

6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.

2. Check the VGA adapter card (if applicable) is inserted properly.

3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps: memory not detected b. 1 long beep and 8 short beeps: VGA not detected

c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Apply the thermal grease onto the CPU heatsink & ensure the CPU fan is well-connected with the CPU heatsink. Check if the CPU fan is working properly while the system is running.

http:// www.ecs.com.tw/ECSWebSite/Support/Support_FAQ.aspx?MenulD=49& childid=M 49&LanlD=0

H110M-C3V/H110M-C3D USER MANUAL

Chapter 5

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.

1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.

2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and

Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.

1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.

2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.

3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

4. Remove the hard drive, optical drive or DDR memory to determine which of these components may be at fault.

areas of high moisture content.

3. Routinely clean the CPU cooler fan to remove dust and hair.

4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.

5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.

6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.

Maintenance and care tips

2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.

5. Check whether there is any bulked up electrolytic capacitor or abnormal component.

Please logo onto our ECS website: http://www.ecs.com.tw/ECSWebSite/Support/ Technical_Support_List.aspx?MenuID=50&LanID=0 for more information.

uB rewoP

desserp si no

.trats ot sliaf CP tub

seY

ylppuS rewoP fi kcehC

tinU

gnikrow si )USP(

dnuos peeB ynA

kcehc dna SOMC RLC

rewop V21 UPC fi

detcennoc si

CP eht tratseR

?draob ro USP htiw melborP

AMR tcatnoc >- melborp draob fI

deulp si droc rewop CA gg

?no denrut si hctiws USP dna

seY

melborp draoB

AMR tcatnoc >-

:speeb trohs 3 fI -

ylreporp ton yromem MMID

eruliaf yromem ro detresni

:speeb trohs 8 dna peeb gnol 1 fI -

detceted ton AGV

seY

neercs TSOP ta tlaH

seY

OMC RL dna SC tser .tra

AMR tcatnoc ,liaf fI

seY

eussi ecived larehpireP

.melborp DDH-

,rorre putes SOMC-

d .SOMCRLC ot een

ts ot liaf metsyS elbatsnu ro tra

es SOIB yfidom re

.gn

M SOC RLC tratser dna

hctiws USP no nruT

tekcos llaw ot tcennoc ro

.tratser dna

h rotinom fi kcehC sa

sid

yalp

rotinom fi kcehC

yalpsid sah

Basic Troubleshooting Flowchart

H110M-C3V/H110M-C3D USER MANUAL

Chapter 5

Memo

ECS H110M-C3V, H110M-C3D User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual