ECS GF8100VM-M3 User Manual
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0b
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD
Corporation.
Other product names used in this manual are the properties of their respective owners
and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Describes features of the
motherboard.
Go to
H
page 1
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Chapter 5
Setting Up N VIDIA RAID Conf iguration
Chapter 6
N VIDIA
®®
® Hybrid SLI
®®
®®
® T echnology Support
®®
Preface
Describes installation of
motherboard components.
Go to
Provides information on using the BIOS Setup Utility.
Go to
Describes the motherboard
software
Go to
Provides information about
SAT A RAID Setup
Go to
Provides information about
Hybrid SLI technology
Go to
H
H
H
H
H
page 7
page 27
page 45
page 51
page 61
TT
ABLE OF CONTENTSABLE OF CONTENTS
T
ABLE OF CONTENTS
TT
ABLE OF CONTENTSABLE OF CONTENTS
Preface i
iii
Chapter 1
Introducing the Motherboard 1
Introduction......................................................................................1
Feature ..............................................................................................2
Motherboard Components.............................................................5
Chapter 2
Installing the Motherboard 7
Safety Precautions...........................................................................7
Choosing a Computer Case............................................................7
Installing the Motherboard in a Case............................................7
Checking Jumper Settings...............................................................8
Setting Jumpers...................................................................8
Checking Jumper Settings...................................................9
Jumper Settings...................................................................9
Installing Hardware........................................................................10
Installing the Processor.....................................................10
Installing Memory Modules...............................................11
Expansion Slots..................................................................15
Connecting Optional Devices..............................................17
Installing a Hard Disk Drive/CD-ROM/SA T A Har d Drive...20
Installing a Floppy Diskette Drive......................................21
Connecting I/O Devices................................................................22
Connecting Case Components....................................................23
Front Panel Header.............................................................25
1
7 7
7
7 7
Chapter 3 27
Using BIOS 27
Using BIOS......................................................................................28
About the Setup Utility ................................................................ 27
The Standard Configuration..............................................27
Entering the Setup Utility...................................................27
BIOS Navigation Keys......................................................28
Standard CMOS Setup......................................................29
Advanced Setup.................................................................31
Advanced Chi pset Setup....................................................32
iv
Integrated Peripherals.......................................................34
Power Ma nagement Setup.................................................35
PCI/PNP Configuration.....................................................37
PC Health Status................................................................38
Frequency/Voltage Contr ol................................................40
Load Default Settings.......................................................41
Supervisor Password........................................................41
User Password..................................................................42
Save & Exit Setup..............................................................42
Exit Without Saving............................................................42
Updating the BIOS.............................................................43
Chapter 4
45 45
45
45 45
Using the Motherboard Software 45
About the Software CD-ROM......................................................45
Auto-installing under W indows XP/Vista..................................45
Running Setup....................................................................46
Ma nual Installation........................................................................50
Utility Software Reference............................................................50
Chapter 5
51 51
51
51 51
Setting Up NVIDIA RAID Configuration 51
Setting Up a Non-Boota ble RAID Array ....................................51
Setting Up a Bootable RAID Array .............................................54
Chapter 6
NVIDIA
®®
® Hybrid SLI
®®
®®
® T echnology Support 61
®®
61 61
61
61 61
Key Features...................................................................................61
Hybrid SLI Products......................................................................62
Hybrid Requirements a nd Constraints.......................................63
Installation a nd Use.......................................................................64
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the GF8100VM-M3 motherboard. This motherboard is a
high performance, enhanced function motherboard that supports socket for
TM
Phenom
Sempron
This motherboard is based on NVIDIA® GeForce8100 (MCP78V) Premium media
and communications processor (MCP) for best desktop platform solution.
GeForce8100 is a single-chip, highly integrated, high performance HyperTransport
peripheral controller, unmatched by any other single chip-device controller. The
memory controller supports DDR2 memory DIMM frequencies of 1066*1 (AM2+)/
800/667/533/400. It supports four DDR2 sockets with maximum memory size of 32
GB*2. High resolution graphics via one PCI Express x16 slot, two PCI Express x1
slots, 12 USB 2.0 ports (6 USB ports and 3 USB 2.0 headers support additional 6 USB
ports) and SATA support with RAID function.
There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and
keyboard connectors, COM, one VGA port, one optional DVI port, six USB ports,
one LAN port and audio jacks for microphone, line-in and 6/8-ch (optional) line-out.
This motherboard is designed in a Micro ATX form factor using a four-layer printed
circuit board and measures 244 mm x 244 mm.
processor (socket AM2+)/AMD AthlonTM 64 X2 Dual-Core/AthlonTM 64/
TM
processors for high-end business or personal desktop markets.
1. Due to the limitation of AMD CPU spec, please refer to Memory QVL
*
for more information.
2. Due to the DRAM maximum size (2 GB per dimm) at present, the
memory maximum size we have tested is 8 GB.
AMD
1
Introducing the Motherboard
2
Feature
Processor
This motherboard uses
• Accommodates AMD Phenom
AMD Athlon
• Supports HyperTransport
HyperTransportTM Technology is a point-to-point link between two devices, it
enables integrated circuits to exchange information at much higher speeds than
currently available interconnect technologies.
This board supports CPU up to 95W TDP only
a socket AM2+/AM2 that carries the following features:
TM
64 X2 Dual-Core/Athlon
TM
processor (socket AM2+)
TM
TM
(HT) 3.0 interface speeds
64/SempronTM processors
Chipset
The NVIDIA® GeForce8100 is a single-chip with proven reliability and performance.
• HyperTransport 3.0 x16 up and down links to the AMD socket AM2+/
AM2 CPU
• PCI Express 16-lane link interface for external graphics processors
• PCI Express Generation 2.0 compatible
• Integrated NVIDIA GeForce® Series DirectX 10 V ertex Shader 4.0 gra ph-
ics processor
• Compliant with PCI v2.3 interface at 33 MHz
• Integrated SATA 3.0 Gb/s Host Controller
• Twelve USB 2.0 ports supported
• Fast ATA-133 IDE controller
• NVIDIA® MediaShieldTM RAID with support for RAID 0, RAID 1, RAID 0+1,
RAID 5, and JBOD
• Integrated Hybrid SLI technology, NVIDIA® UltraShadowTM technology,
full NVIDIA® nView® multi-display technology capability
There are three Hybrid SLI modes for you to select: Save Power,
Boost Performance and Additional Displays.
Memory
• Supports DDR2 1066 (AM2+)/800/667/533/400 DDR2 SDRAM with Dual-
channel architecture
• Accommodates four unbuffered DIMMs
• Up to 8 GB per DIMM with maximum memory size up to 32 GB*
Introducing the Motherboard
Audio (Optional)
The onboard Audio provides either of the following features:
• 5.1 Channel High Definition Audio Codec
• DACs Support 96K/48K/44.1KHz DAC sample rate
• Power support: Digital:3.3V; Analog:5.0V
• WOW
• Provides single ended CD input with DRM solutions and legacy
• 7.1 Channel High Definition Audio Codec
• SPDIF In/Out supports 96K/48K/44.1KHz plus SPDIF OUT sup-
• Power support: Digital:3.3V; Analog:5.0V
• MAxx PlayerTM from Waves
• Provides single ended CD input with DRM solutions and legacy
TM
and Tru SurroundTM from SRS
OS issues
ports 88.2 KHz
OS issues
Onboard LAN (Optional)
The onboard LAN provides either of the following features:
• Compliant with 1000Base-T IEEE 802.3ab, 100Base-TX IEEE 802.3u
• Supports half/full duplex operation
• IEEE 802.3 compliant RGMII/MII
• 10/100 full/half duplex operation
• Supports RMII mode, MII, and 7-wire SNI (Serial Network Interface)
• IEEE 802.3/802.3u compliant
3
Expansion Options
The motherboard comes with the following expansion options:
• One PCI Express x16 slot for Graphics Interface
• Two PCI Express x1 slots
• One 32-bit PCI v2.3 compliant slot
• One IDE connector supporting up to two IDE devices
• One floppy disk drive interface
• Six 7-pin SATA connectors
This motherboard supports Ultra DMA bus mastering with transfer rates of 133/
100/66/33 Mb/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• Two PS/2 ports for mouse and keyboard
• One serial port
• One VGA port
• One optional DVI port
• Six USB ports
• One LAN port
• Audio jacks for microphone, line-in and 6/8-ch (optional) line-out
Introducing the Motherboard
4
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system
features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1. Some hardware specifications and software items are subject to change
without prior notice.
2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50
°C.
Introducing the Motherboard
Motherboard Components
5
Introducing the Motherboard
6
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket
2. CPU_FAN CPU cooling fan connector
3. DDR2_1~4 240-pin DDR2 SDRAM slots
4. FDD Floppy disk drive connector
5. ATX_POWER Standard 24-pin ATX power connector
6. IDE Primary IDE connector
7. SAT A1~6 Serial ATA connectors
8. F_PANEL Front Pan el Switch /LE D header
9. SPK Speak er header
10. CLR_CMOS Clear CM O S jum per
11. USBPWR_F1~2 Front Panel USB Power Select jumper
12. F_USB1~3 Front Panel USB headers
13. LPT Par allel po rt header
14. SPDIFO SPDIF out header
15. CD_IN Analog Audio Input connector
16. F_AUDIO Front Panel Audio header
17. PCI 32-bit add-on card slots
18. PCIEX16 PCI Express x16 graphics card slot
19. PCIE1~2 PCI Express x1 slots
20. SYS_FAN System Fan connector
21. USBPWR_R1~2 Rear USB/PS2 Power Select jumper
22. ATX12V 4-pin +12V power connector
Socket f o r AMD P h en o m
TM
64 X2 Dual-Core/AthlonTM 64/SempronTM processors
Athlon
TM
processor (socket AM2+)/AMD
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid damage from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies
with the specifications for the Micro ATX system case. Firstly, some features on the
motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the
features required. Secondly, this motherboard supports one floppy diskette drive and
two enhanced IDE drives. Make sure that your case has sufficient power and space for
all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries a Micro ATX form factor of 244 x 244 mm. Choose a case
that accommodates this form factor.
7
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the jumper
caps are placed on the correct pins.
The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.
This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT
SHORT OPEN
Installing the Motherboard
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is
labeled.
Jumper Settings
Jumper Type Description Setting (default)
1-2: NORMAL
CLR_CMOS
3-pin
CLEAR CMOS
2-3: CLEAR
Before clearing the
CMOS, make sure to
turn the system off.
1
CLR_CMOS
9
USBPWR_R1~2
USBPWR_F1~2
To avoid the system instability after clearing CMOS, we recommend
1.
users to enter the main BIOS setting page to “Load Optimized Defaults”
and then “Save & Exit Setup”.
Make sure the power supply provides enough VCC5_DUAL voltage
2.
before selecting the VCC5_DUAL function.
3.
It is required that users place the USBPWR_F & USBPWR_R cap onto
2-3 pin rather than 1-2 pin as default if you want to wake up the
computer by USB/PS2 KB/Mouse.
3-pin
3-pin
Rear USB/PS2
Power Select
Jumper
Front Panel
USB Power
Select Jumper
1-2: VCC5
2-3: VCC5_DUAL
1-2: VCC5
2-3: VCC5_DUAL
Installing the Motherboard
1
USBPWR_R1~2
1
USBPWR_F1~2
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes
across the motherboard, you may cause serious damage to the motherboard
or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change the settings in the system
Setup Utility. We strongly recommend that you do not over-clock processors or
other components to run faster than their rated speed.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components
that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from the
power outlet before installing or removing the motherboard or other
hardware components.
This motherboard has a socket AM2+/AM2 processor socket. When choosing a
processor, consider the performance requirements of the system. Performance is
based on the processor design, the clock speed and system bus frequency of the
processor, and the quantity of internal cache memory and external cache memory.
Installing the Motherboard
CPU Installation Procedure
The following illustration shows CPU installation components.
1 Unhook the locking lever of the CPU socket. Pull the
locking lever away from the socket and raising it to
the upright position.
2 Match the pin1 corner marked as the beveled edge
on the CPU with the pin1 corner on the socket. Insert
the CPU into the socket. Do not use force.
3 Push the locking lever down and hook it under the
latch on the edge of socket.
4 Apply thermal grease to the top of the CPU.
5 Install the cooling fan/heatsink unit onto the CPU, and
secure them all onto the socket base.
6 Plug the CPU fan power cable into the CPU fan
connector (CPU_FAN) on the motherboard.
To achieve better airflow rates and heat dissipation, we suggest that you
use a high quality fan with 4800 rpm at least. CPU fan and heatsink
installation procedures may vary with the type of CPU fan/heatsink
supplied. The form and size of fan/heatsink may also vary.
11
Installing Memory Modules
This motherboard accommodates four memory modules. It can support four 240-pin
DDR2 1066 (AM2+)/800/667/533/400. The total memory capacity is 32 GB*.
DDR2 SDRAM memory module table
Memory module Memory Bus
DDR2 400 200 MHz
DDR2 533 266 MHz
DDR2 667 333 MHz
DDR2 800 400 MHz
DDR2 1066 533 MHz
You must install at least one module in any of the four slots. Each module can be
installed with 8 GB of memory; total memory capacity is 32 GB*.
The four DDR2 memory sockets (DDR2_1, DDR2_2, DDR2_3, DDR2_4) are divided into two channels and each channel has two memory sockets as following:
Channel 0: DDR2_1, DDR2_2
ff
Channel 1: DDR2_3, DDR2_4
ff
Installing the Motherboard
12
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always
wear a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR2 SDRAM only.
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install any remaining DIMM modules.
For best performance and compatibility, we recommend that users
install DIMMs in the sequence of DIMM3, DIMM4, DIMM1 and
DIMM2.
Recommend configuration for best performance and compatibility
Numb e r o f DIMMs DIMM 1 DIMM 2 DIMM 3 DIMM 4 AM 2 AM2+ *
1
2
3
4
Single Channel
Dual Channel
Single Channel
Dual Channel
Unganged Mode
Ganged Mode
Unganged Mode
Ganged Mode
:operation with normal performance
:operation with the best performance
Installing the Motherboard
Ta ble A: DDR2 (memory module) QVL (Qualified V endor List)
The following DDR2 1066 (AM2+)/800/667/533/400 memory modules have been
tested and qualified for use with this motherboard.
Type Size Vendor Module Name
M378T3354BZ0-CCC
K4T51163QB-ZCCC
M378T6553BG0-CCC
K4T51083QB-GCCC
Japan E2508AA-T7F-E
Hynix HY5PS121621
Nanya N T5TU32M16AG-37B
5PB42 D 9DCD
Elpida D5116AF-5C-E
AET93F370 SS
AET94F370 DS
Samsung K4T51083QB-ZCD5
VS512MB533D2 64M8CEC
Elpida 04180W B01
Hynix HY5PS12821
Nanya N T5TU64M8AE-37B
5PB32 D9DCN
6AD11 D9GCT
Elpida E5108AG-5C-E
PC2-4200U-4444-10-B1
K4T51083QF-ZCD5
PC2-4200U-4444-12-D S
K4T51083QC
Elpida E5108AB-5C-E
Samsung 8D22JB-KM
DDR2 400
DDR2 533
256 MB
512 MB
256 MB
512 MB
1 GB
Samsung
Samsung
TwinMos Samsung K4T51083QB-GCCC
Corsair VC256MB533D2 4PB11D9CHM
Elpida
Kingmax
Nanya
Ramaxel
Aeneon
Corsair
Elpida
Hynix Hynix HY5PS12821
I nfineon H Y818T512800AF37 33346778
Kingston
Ramaxel
Samsung
Tw inMos
Apacer Elpida E5108AB-5C-E
GEIL A016E2864T 2AG8AKT5H120001
Infineon HY818T512800AF37 33344539
Kingmax KKE A88E4AAKG-37
UMAX U2S12D30TP-5C
13
Installing the Motherboard
14
Type Size Vendor Module Name
256 MB
Ramaxel
A-DATA
Corsair
5NB31 D9DCG
AD29608A88-3EG
VALUESELEC T 32M8CEC
GEIL GL2L64M 088BA18W
DDR2 667
DDR2 800
512 MB
1 GB
512 MB
1 GB
Ramxel
Samsung
Sync MAX
Transcend
Tw inm os
Kingston
Samsung
UMAX
I nfineon
U2S12030TP-6E TBF 614-L93G
Infineon HYB18T256 800AF25
Infinity
Kingston
Apacer
I nfinity 04701G16CZ5U2G
Kingston
5LB31 D9DCL
K4T51083QC
PC35300U-25331-Z
K4T56083QF-ZCE6
04400WB01 R050008A
JetRam J1 2Q3AB-6
TMM6208G 8M30B
KVR667D2N5/1G
K4T51083QC
04751208CZ5U2D
KVR800D2N5/512
Apacer
AM4B5708BPJS8E0634E
KVR800D2N5/1G
UMAX U2S12D30TP-8E
Type Size Vendor
512 MB
DDR2 1066
1 GB
2 GB
Module Name
Kingston
Apacer 78.0AG9S.9K4 1.9 V
Micron MT8HTF12864AY-1GAE1 1.9 V
OCZ OCZ2RPR10662GK 1.9 V ~ 2.3 V
Qimonda HYS64T128020EU-19F-C
Apacer
Micron MT16HTF25664AY-1GAE1 1.9 V
KVR1066D2N7/512 1.8V /
9905315-094.A00LF
KVR1066D2N7/1G 1.8V /
9905316-106.A01LF
78.AAGAL.9KF 1.9V
Memory
Rec ommend Volt
1.8 V
1.8 V Kingston
1.9 V
Due to the Phenom CPU and memory module limitation, the DRAM may
need to adjust the voltage for supporting DDR2 1066. The memory modules
which can be used stably are listed in the above QVL table for reference.
Installing the Motherboard
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them
to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can
increase the motherboard’s capabilities by adding hardware that performs tasks that
are not part of the basic system.
15
PCIEX16 Slot The PCI Express x16 slot is used to install an external PCI Express
PCIE1~2 Slots
PCI Slot This motherboard is equipped with one standard PCI slot. PCI stands
graphics card that is fully compliant to the PCI Express Base Specification revision 2.0.
The PCI Express x1 slots are fully compliant to the PCI Express
Base Specification revision 1.1 as well.
for Peripheral Component Interconnect and is a bus standard for
expansion cards, which for the most part, is a supplement of the
older ISA bus standard. The PCI slot on this board is PCI v2.3
compliant.
Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.
Installing the Motherboard
16
Follow these instructions to install an add-on card:
1 Remove a blanking plate from the system case corresponding to the
slot you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network
adapters, you have to install drivers and software before you can begin
using the add-on card.
Ta ble B: Supported V GA Card List for Hybrid SLI T echnology
Hybrid SLI Technology GPUs
H ybrid Power G eFo rce B oost
GeForce 9800 GX2 Yes No
GeForce 8500 GT No Yes
GeForce 8400 GS No Yes
Installing the Motherboard
Loading...