ECS G41T-MR23 User Manual
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s
manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Chatper 5
Setting Up eJIFFY
Chatper 6
Trouble Shooting
Describes features of the
motherboard.
Go to
Describes installation of motherboard
components.
Go to
Provides information on using the
BIOS Setup Utility.
Go to
Describes the motherboard software.
Go to
Describes the eJIFFY setting up
Go to
Provides basic trouble shooting tips
H
H
H
H
H
H
page 1
page 7
page 29
page 49
page 53
page 63Go to
Preface
TT
ABLE OF CONTENTSABLE OF CONTENTS
T
ABLE OF CONTENTS
TT
ABLE OF CONTENTSABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction......................................................................................1
Feature...............................................................................................2
Specifications....................................................................................5
Motherboard Components.............................................................6
iii
Chapter 2
Installing the Motherboard 7
Safety Precautions............................................................................7
Choosing a Computer Case.............................................................7
Installing the Motherboard in a Case............................................7
Checking Jumper Settings...............................................................8
Setting Jumpers...................................................................8
Checking Jumper Settings...................................................9
Jumper Settings...................................................................9
Installing Hardware........................................................................10
Installing the Processor.....................................................10
Installing Memory Modules...............................................12
Expansion Slots.................................................................18
Connecting Optional Devices............................................20
Installing a Hard Disk Drive/CD-ROM/SA T A Hard Drive..22
Connecting I/O Devices................................................................24
Connecting Case Components.....................................................25
Front Panel Header...........................................................28
7 7
7
7 7
Chapter 3 29
Using BIOS 29
About the Setup Utility ................................................................ 29
The Standard Configuration..............................................29
Entering the Setup Utility....................................................29
Resetting the Default CMOS V alues...................................30
Using BIOS......................................................................................31
Standard CMOS Setup.......................................................32
Advanced Setup..................................................................34
Advanced Chipset Setup.....................................................37
Integrated Peripherals........................................................38
Power Management Setup..................................................39
iv
PCI/PnP Setup...................................................................40
PC Health Status................................................................40
Frequency/Voltage Control.................................................45
Load Default Settings.........................................................46
Supervisor Password.........................................................46
User Password...................................................................47
Save & Exit Setup................................................................47
Exit Without Saving.............................................................47
Updating the BIOS...............................................................48
Chapter 4
49 49
49
49 49
Using the Motherboard Software 49
About the Software DVD-ROM/CD-ROM.................................49
Auto-installing under Windows XP/V ista/7...............................49
Running Setup....................................................................50
Manual Installation........................................................................52
Utility Software Reference............................................................52
Chapter 5
53 53
53
53 53
Setting Up eJIFFY 53
Introduction..........................................................................................53
Installation and BIOS Setup.................................................................54
Entering eJIFFY.............................................................................................57
Features Icons...........................................................................................58
Usage FAQ.................................................................................................59
Chapter 6
63 63
63
63 63
T r ouble Shooting 63
Start up problems during assembly.......................................................63
Start up problems after prolong use.................................................64
Maintenance and care tips..................................................................64
Basic Troubleshooting Flowchart...................................................65
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the G41T-MR23 motherboard. This motherboard is a high
performance, enhanced function motherboard designed to support the LGA775 socket
®
Intel
Conroe/Presler/Wolfdale/Yorkfield processors for high-end business or per-
sonal desktop markets.
®
The motherboard incorporates the Intel
Southbridge (SB) chipsets.
quency of 1333/1066/800 MHz using a scalable FSB Vcc_CPU. The memory controller supports DDR3 memory DIMM frequencies of 1333 (OC)/1066/800; DDR2
memory DIMM frequency of 800. It supports two DDR3 sockets with up to maximum memory of 8 GB or two DDR2 sockets with up to maximum memory of 8 GB.
High resolution graphics via one PCI Express slot, intended for Graphics Interface,
is fully compliant to the PCI Express Gen 1.
The ICH7 Southbridge supports one PCI slot which is PCI v2.3 compliant. In addition, one PCI Express x1 slot is supported, fully compliant to the PCI Express Base
Specification revision 1.0. It implements an EHCI compliant interface that provides
480 Mb/s bandwidth for eight USB 2.0 ports (four USB ports and two USB 2.0 headers
support additional four USB ports). One onboard IDE connector supports two IDE
devices in Ultra ATA100/66/33 mode. The Southbridge integrates a Serial ATA host
controller, supporting four SATA ports with maximum transfer rate up to 3.0 Gb/s
each.
The Northbridge supports a Front Side Bus (FSB) fre-
G41 Northbridge (NB) and Intel® ICH7
1
The motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 mouse and keyboard connectors, one VGA port, four USB ports, one
LAN port, and audio jacks for microphone, line-in and line-out.
Introducing the Motherboard
2
Feature
Processor
The motherboard uses an LGA775 type of Intel® Conroe/Presler/Wolfdale/
Yorkfield processors that carries the following features:
• Intel® Conroe/Presler/Wolfdale/Yorkfield processors
• Supports a system bus (FSB) of 1333/1066/800 MHz
• LGA775 socket for latest Intel® 45nm Multi-Core processors
This board supports CPU up to 95W TDP.
Chipset
The Intel® G41 Northbridge (NB) and Intel® ICH7 Southbridge (SB) chipsets are
based on an innovative and scalable architecture with proven reliability and
performance.
G41 (NB)
ICH7 (SB)
• Supports 36-bit host bus addressing, allowing the CPU
to access the entire 64 GB of the memory address
space
• 2 GB/s point-to-point Direct Media Interface (DMI) to
ICH7 (1 GB/s each direction)
• Supports 2-GB, 1-Gb, 512 Mb DDR2 DRAM technologies for x8 and x16 devices
• Supports 1-Gb, 512 Mb DDR3 DRAM technologies for
x8 and x16 devices
• One, 16-lane (x16) PCI Express port intended for external device attach, fully compatible to the PCI Express Gen 1
• An integrated graphics device (IGD) delivering cost
competitive 3D, 2D and video capabilities
• Microsoft DX10 and 128MB share memory are supported
• Enhanced DMA Controller , interrupt controller, and timer
functions
• Compliant with PCI Express Base Specification, Revision 1.0a
• Compliant with PCI v2.3 specification
• Integrated SATA 3.0 Gb/s Host Controller
• Integrated USB 2.0 Host Controller supporting up to
eight USB 2.0 ports
• Integrated IDE controller supports Ultra ATA 100/66/33
Memory
• Supports DDR3 1333 (OC)/1066/800 DDR3 SDRAM with Dual-channel
architecture
• Supports DDR2 800 DDR SDRAM with Dual-channel architecture
• Accommodates two unbuffered DIMMs
• 2 x 240-pin DDR3 DIMM sockets support up to 8 GB
• 2 x 240-pin DDR2 DIMM sockets support up to 8 GB
Users pleased be noted that DDR3 & DDR2 memory modules can not be
installed at the same time.
Introducing the Motherboard
Onboard LAN (optional)
• Supports PCI ExpressTM 1.1
• Integrated 10/100/1000 transceiver
• Wake-On-LAN (WOL) and remote wake-up support
• Supports PCI ExpressTM 1.1
• Integrated 10/100 transceiver
• Wake-On-LAN (WOL) and remote wake-up support
Audio
This motherboard may support either of the following Audio chipsets:
• 5.1 Channel High Definition Audio Codec
• Exceeds Microsoft Windows Logo Program (WLP) Requirements
• ADCs support 44.1K/48K/88.2K/96K/192KHz sample rate
• Power Support: Digital: 3.3V; Analog: 5.0V
Expansion Options
The motherboard comes with the following expansion options:
• One PCI Express x16 slot for Graphic Interface
• One PCI Express x1 slot
• One 32-bit PCI v2.3 compliant slot
• One IDE connector that supports two IDE devices
• Four 7-pin SATA connectors
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• Two PS/2 ports for mouse and keyboard
• One VGA port
• Four USB ports
• One LAN port
• Audio jacks for microphone, line-in and line-out
3
Introducing the Motherboard
4
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure many system
features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1.Some hardware specifications and software items are subject to change
without prior notice.
2.Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50°C.
Introducing the Motherboard
Specifications
CPU
Chipset
Memory
• LGA775 socket for latest Intel
• Supports “Hyper-Threading” technology CPU
• Northbridge: Intel G41 Southbridge: Intel ICH7
• Dual-channel DDR3 1333 memory architecture
• Dual-channel DDR2 800 memory architecture
• 2 x 240-pin DDR3 DIMM sockets support up to 8 GB
• 2 x 240-pin DDR2 DIMM sockets support up to 8 GB
• Supports DDR3 1333 (OC)/1066/800 DDR3 SDRAM
• Supports DDR2 800 DDR2 SDRAM
Yorkfield processors
®
Conroe/Presler/Wolfdale/
5
Expansion
Slots
Storage
Audio
LAN
Rear Panel I/O
Internal I/O
Connectors &
Headers
System BIOS
• 1 x PCI Express x16 slot
• 1 x PCI Express x1 slot
• 1 x PCI slot
• Supported by Intel ICH7 chipset
• 4 x Serial ATA 3.0 Gb/s Host Controllers
• VIA VT1705 6-CH High definition audio CODEC
• Realtek RTL8103EL 10/100M Fast Ethernet Controller or
TL8111DL Giga Ethernet Controller (optional)
R
• 1 x PS/2 keyboard & PS/2 mouse combo connector
• 1 x VGA port
• 4 x USB ports
• 1 x RJ45 LAN connector
• 1 x Audio port (Line in, microphone in and 6-ch line out)
• 1 x 24-pin ATX Power Supply connector
• 1 x 4-pin ATX12V connector
• 4 x Serial ATA connectors
• 1 x CPU_FAN connector
• 1 x SYS_FAN connector
• 2 x USB 2.0 headers support additional 4 USB ports
• 1 x Serial header
• 1 x Chassis detect header
• 1 x Front panel header
• 1 x SPDIF out header
• 1 x Front panel audio header
• AMI BIOS with 8Mb SPI ROM
• Supports Plug and Play, STR (S3) / STD (S4) , Hardware
monitor, Multi Boot
• F11 hot key for boot up devices option
• Support PgUp clear CMOS hotkey
Form Factor
• Micro ATX Size, 225 mm x 190 mm
Introducing the Motherboard
6
/
Motherboard Components
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket
2. CPU_FAN CPU cooling fan connector
3. DDR3_1~2 240-pin DDR3 SDRAM slots
4. DDR2_1~2 240-pin DDR2 SDRAM slots
5. ATX_POWER Standard 24-pin ATX power connector
6. IDE Primary IDE channel
7. SYS_FAN System cooling fan connector
8. SATA3~4 Serial ATA connectors
9. CASE Chassis detect header
10. CLR_CMOS Clear CMOS jumper
11. SATA1~2 Serial ATA connectors
12. USBPWR_F Front panel USB power select jumper
13. F_USB1~2 Front panel USB headers
14. F_PANEL Front panel switch/LED header
15. COM Onboard serial port header
16. SPDIFO SPDIF out header
17. F_AUDIO Front panel audio header
18. PCI 32-bit add-on card slot
19. PCIE PCI Express x1 slot
20. PCIEX16 PCI Express x16 graphics card slot
21. USBPWR_R Rear panel USB PS/2 power select jumper
22. ATX12V 4-pin +12V power connector
This concludes Chapter 1. The next chapter explains how to install the motherboard.
LGA775 socket for Intel
Wolfdale/Yorkfield processors
®
Conroe/Presler
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid damage from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies
with the specifications for the Micro ATX system case. First, some features on the
motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the
features required. Secondly, this motherboard supports two enhanced IDE drives.
Make sure that your case has sufficient power and space for all drives that you intend
to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries a Micro ATX form factor of 225 x 190 mm. Choose a case
that accommodates this form factor.
7
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in
a case.
Most system cases have mounting brackets installed in the case, which correspond
the holes in the motherboard. Place the motherboard over the mounting brackets
and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion
slots on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the jumper
caps are placed on the correct pins.
The illustrations show a 2-pin jumper.
When the jumper cap is placed on both
pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper
cap on just one pin, the jumper is OPEN.
This illustration shows a 3-pin jumper.
Pins 1 and 2 are SHORT.
SHORT OPEN
Installing the Motherboard
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is
labeled.
Jumper Settings
9
Jumper
CLR_CMOS
USBPWR_F
USBPWR_R 3-pin
Type
3-pin
3-pin
1. To avoid the system instability after clearing CMOS, we recommend
users to enter the main BIOS setting page to “Load Default Settings” and
then “Save and Exit Setup”.
2. Make sure the power supply provides enough 5VSB voltage before selecting the 5VSB function.
3. It is required that users place the USBPWR_F & USBPWR_R cap onto 23 pin rather than 1-2 pin as default if you want to wake up the computer by
USB/PS2 KB/Mouse.
Description Setting (default)
1-2: NORMAL
Clear CMOS
Front Panel
USB Power
Select Jumper
Rear USB PS/2
Power Select
Jumper
2-3: CLEAR
Before clearing the
CMOS, make sure to
turn off the system.
1-2: VCC
2-3: 5VSB
1-2: VCC
2-3: 5VSB
Installing the Motherboard
1
CLR_CMOS
1
USBPWR_F
1
USBPWR_R
10
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure
that you DO NOT scratch the motherboard or any of the surfacemount resistors with the clip of the cooling fan. If the clip of the cooling
fan scrapes across the motherboard, you may cause serious damage
to the motherboard or its components.
On most motherboards, there are small surface-mount resistors near
the processor socket, which may be damaged if the cooling fan is
carelessly installed.
Avoid using cooling fans with sharp edges on the fan casing and the
clips. Also, install the cooling fan in a well-lit work area so that you
can clearly see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change the settings in the system
Setup Utility. We strongly recommend that you do not over-clock processors or
other components to run faster than their rated speed.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from
the power outlet before installing or removing the motherboard or
other hardware components.
This motherboard has an LGA775 socket. When choosing a processor, consider the
performance requirements of the system. Performance is based on the processor
design, the clock speed and system bus frequency of the processor, and the quantity
of internal cache memory and external cache memory.
Fail-Safe Procedures for Over-clocking
When end-users encounter failure after attempting over-clocking, please take the
following steps to recover from it.
1. Shut down the computer.
2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the
PC up.
3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.
4. The BIOS returns to the default setting by itself.
Installing the Motherboard
CPU Installation Procedure
The following illustration shows CPU installation components.
A. Read and follow the instructions shown
on the sticker on the CPU cap.
B. Unload the cap
· Use thumb & forefinger to hold the
lifting tab of the cap.
· Lift the cap up and remove the cap
completely from the socket.
C. Open the load plate
· Use thumb & forefinger to hold the
hook of the lever, pushing down and
pulling aside unlock it.
· Lift up the lever.
· Use thumb to open the load plate. Be
careful not to touch the contacts.
D. Install the CPU on the socket
· Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.
E. Close the load plate
· Slightly push down the load plate onto
the tongue side, and hook the lever.
· CPU is locked completely.
11
F. Apply thermal grease on top of the CPU.
G. Fasten the cooling fan supporting base
onto the CPU socket on the motherboard.
H. Make sure the CPU fan is plugged to the
CPU fan connector. Please refer to the
CPU cooling fan user’s manual for more
detail installation procedure.
1. To achieve better airflow rates and heat dissipation, we suggest
that you use a high quality fan with 3800 rpm at least. CPU fan and
heatsink installation procedures may vary with the type of CPU fan/
heatsink supplied. The form and size of fan/heatsink may also vary.
2. DO NOT remove the CPU cap from the socket before installing a
CPU.
3. Return Material Authorization (RMA) requests will be accepted
only if the motherboard comes with the cap on the LGA775 socket.
Installing the Motherboard
12
Installing Memory Modules
This motherboard accommodates two memory modules. It can support two 240-pin
DDR3 1333 (OC)/1066/800, the total memory capacity is 8 GB; it can also support
two 240-pin DDR2 800, the total memory capacity is 8 GB too.
Users pleased be noted that DDR3 & DDR2 memory modules can not be
installed at the same time. When DDR3 memory modules have been installed, you can not install DDR2 memory modules, vice versa.
DDR3 SDRAM memory module table
Memory module Memory Bus
DDR3 1333 667 MHz
DDR3 1066 533 MHz
DDR3 800 400 MHz
You must install at least one module in any of the two slots. The total memory
capacity is up to 8 GB.
DDR2 SDRAM memory module table
Memory module Memory Bus
DDR3 800 400 MHz
You must install at least one module in any of the two slots. The total memory
capacity is up to 8 GB.
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always
wear a grounding strap when you handle the modules.
Installing the Motherboard
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR3/DDR2 SDRAM .
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install another DDR3 or DDR2 DIMM module.
13
DDR3 DIMM slots: Yellow
DDR2 DIMM slots: Orange
Installing the Motherboard
14
Table A: DDR2 (memory module) QVL (Qualified V endor List)
The following DDR2 800/667 memory modules have been tested and qualified for
use with this motherboard.
Type
DDR2 667
DDR2 800
Si ze Vendor Module Name
512 MB Micron MT4HTF6464AY-667E 1
Apacer
Corsair VS1GB667D2
Kingston KVR667D2N5
1 GB
2 GB
1 GB
Micron M T8HTF 12864AY-667E 1
PSC
Samsung Gold Bar M378T2863DZS
Apacer 78.A1G9O.9K4
Hynix HYMP125U 64AP8-Y5
Kingston KVR667D2N5
LeadMax PC2-5300U
PSC AL8E8F73C- 6E1
A-DATA M2GVD6G3I41P0U 1E5E
Apacer
Geil Geil Millenary
Hynix HYM P112U64CP 8-S6 AB
KingMax KLDD48F-B8KU5 NGES
Kingston KVR800D2N5/1G 1.8V 9905316-054.A01LF
Nanya NT1GT64U88D0BY-AD
Ramaxel RML1320EH38D7F-800
Samsung
Transcend DDR/DIMM 5-5-5
Uni fosa GU341G0ALEPR6B2C6CE
Golden Bar M378T2953EZ3-CE7 0726
78.01G9O.9K5
667/AU01GE667C5K B GC
AL7E8E63B-6E1T
AL7E8F63J-6E1
AL7E8F73C-6E1
78.01GAO.9K5
78.01GA0.9L5
AU01GE800C5KBGC
M 378T2863EHS-CF7
Installing the Motherboard
Table B: DDR3 (memory module) QVL (Qualified V endor List)
The following DDR3 2200/2133/2000/1800/1600/1333/1066/800* memory modules have been tested and qualified for use with this motherboard.
15
Type
DDR3 800
DDR3 1066
Si ze Vendor Module Name
512 MB Qimonda IMSH51U03A1F1C-08E
512 MB
1 GB
2 GB
Elpida PC3-8500U-7-00-AP
Kingston KVR1066D3N7/512
Aeneon AEH760UD00-10FA98X
Elpida EBJ10UE8BDF0-AE-F
Hynix
Kingston KVR1066D3N7
Qimonda
Samsung M378B2873EH1-CF8
Mic ron
Ramaxel RMR1810NA48E7F-1066-LF
Elixir
Elpida EBJ21UE8BDF0-AE-F
Hynix
Mic ron
Nanya M2Y2G64TU8HD5B-BD
Qimonda
Samsung
HYMT112U64ZNF8-G8 AA
HMT112U6AFP8C-G7N0 AA
I MSH1GU03A1F1C-10F
I MSH1GU03A1F1C-10G
MT8JTF12864AY-1G1D 1
MT8JTF12864AY-1G1D 1
MT8JTF12864AZ-1G1F1
M 378B2873DZ1-CF8Samsung
M 2Y2G64CB8HC9N-BE
M 2Y2G64CB8HC5N-BE
HYMT125U64ZNF8-G8 AA
HMT125U6AFP8C-G7N0 AA
MT16JTF25664AY-1G1D1
MT16JTF25664AY-1G1D1
MT16JTF25664AZ-1G1F1
I MSH2GU13A1F1C-10F
I MSH2GU13A1F1C-10G
M 378B5673DZ1-CF8
M 378B5673DZ1-CF8
Installing the Motherboard
16
Type Size Vendor Module Name
DDR3 1333
A-DATA AD3U1333B1G9-B
Aeneon AXH760UD00-13GA98X
Elixir M2Y1G64CB88A5N-CG
El pida EBJ10U E8BDF0-DJ -F
Hynix HMT112U6AFP8C-H9N0 AA
KingsMax FLFD45F-B8KG9 NAUS
KingMax FLFD45F-B8KG9 NAES
Kingston
Mic r on
1 GB
Nanya NT 1GC64B88A0NF-CG
PSC AL 7F8 G73D-DG1
Qimonda IMSH1GU13A1F1C-13H
Ramaxel
Samsung
Silicon Pow er SP001GBLTU133S01
Unifosa GU502203EP0201
A-DATA AD3U1333B2G9-B
A-data Game A-DATA 8-8-8-24
Apacer 78.A1GC6.9L1
Elixir
El pida EBJ21U E8BDF0-DJ -F
G.SKILL
Hynix HMT125U6AFP8C-H9N0 AA
KingMax FLFE85F-B8KG9 NEES
KingsMax FLFE85F -B8KG9 NEUS
2 GB
Kingston
Micron MT16JTF25664AY-1G4D 1
Nanya NT2GC64B8HAONF-CG
PSC AL 8F8 G73D-DG1
Qimonda IMSH2GU13A1F1C-13H
Ramaxel RMR186EA48D8F-1333
Samsung
Unifosa GU512303EP0202
Winchip GDF2GB18L150C8
Kingston KVR1333D3N9/4G
4 GB
Samsung M378B 5273CH0-CH9
KVR1333D3N9
KVR1333D3N9
MT8JTF12864AY-1G4D1
MT8JTF12864AZ-1G4F1
RMR1810KD48E7F-1333
RMR1810E7F-1333
M378B2873DZ1-CH9
M378B2873EH1-CH9
M378B2873FHS-CH9
M2F2G64CB8HA4N-CG
M2Y2G64CB8HC9N-CG
M2Y2G64CB 8HA5N-CG
F3-10666CL9D-4GBRL
F3-10666CL8D-4GBECO 1.35V
F3-10666CL9D-4GBNQ
KVR1333D3N9
KVR1333D3N9
KVR1333D3N9K2/2G
KVR1333D3N9/2G
M378B5673EH1-CH9
M378B5673FH0-CH9
Installing the Motherboard
17
Type
DDR3 1600
DDR3 1800
DDR3 2000
DDR3 2133
DDR3 2200
Users pleased be noted that DDR3 2200/2133/2000/1800/1600 are defaulted
as DDR3 1333 to pass the test.
Size Vendor Module Name
1 GB A-DATA Super speed flying dragon
A-DATA AX3U1600GB2G9-AG ()
E lixir M2Y2G64CB8HA9N-DG
F3-12800C L9D-4GBNQ
2 GB
1 GB Kingston KHX1800C9D3K3/3GX
2 GB Corsair TR3X6G1866C9D
2 GB Apacer 78.AAGD5.9KD
2 GB Kingston KHX2133C 9D3T 1K2/4GX
2 GB
G.SKILL
KingsM ax
G.SKILL F3-17600C L7D-4GBPIS
Kingmax FLKE85F-B8KJ A FEIH
F3-12800CL9D-4GBECO 1.35V
F3-12800CL7D-4GBECO 1.35V
F3-12800CL9D-4GBRL
FLGD45F-B8KG9 NEES
FLGE85F-B8KG 9 NEES
Installing the Motherboard
Loading...