ECS A890GXM-A User Manual
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’ s
manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Chapter 5
Setting Up AMD SB850 RAID
Configuration
Chatper 6
Setting Up eJIFFY
Chapter 7
Trouble Shooting
Describes features of the motherboard.
Go to
Describes installation of motherboard
components.
Go to
Provides information on using the BIOS
Setup Utility.
Go to
Describes the motherboard software
Go to
Provides information about SATA RAID
Setup
Go to
Describes the eJIFFY setting up
Go to
Provides basic troubleshooting tips
Go to
H
H
H
H
H
H
H
page 1
page 7
page 25
page 45
page 49
page 57
page 67
Preface
TT
ABLE OF CONTENTSABLE OF CONTENTS
T
ABLE OF CONTENTS
TT
ABLE OF CONTENTSABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction............................................................................................1
Features...................................................................................................2
Motherboard Components...................................................................4
iii
Chapter 2
Installing the Motherboard 7
Safety Precautions...............................................................................7
Choosing a Computer Case..................................................................7
Installing the Motherboard in a Case.................................................7
Installing Hardware............................................................................8
Installing the Processor...................................................................8
Installing Memory Modules...........................................................10
Expansion Slots.............................................................................14
Connecting Optional Devices........................................................16
Installing a SATA Hard Drive.......................................................18
Connecting I/O Devices......................................................................19
Connecting Case Components..........................................................20
Front Panel Header.......................................................................23
Chapter 3
Using BIOS 25
About the Setup Utility ....................................................................25
The Standard Configuration..........................................................25
Entering the Setup Utility...............................................................25
Resetting the Default CMOS V alues...............................................26
Using BIOS............................................................................................27
Standard CMOS Setup..................................................................28
Adva nced Setup.............................................................................30
Advanced Chipset Setup................................................................32
Integrated Peripherals..................................................................33
Power Ma nagement Setup.............................................................34
PCI/PnP Setup...............................................................................35
PC Health Status...........................................................................35
M.I.B. III (MB Intelligent Bios)......................................................39
25 25
25
25 25
77
7
77
iv
Load Default Settings....................................................................42
Supervisor Password.....................................................................42
User Password...............................................................................43
Save & Exit Setup ..........................................................................43
Exit Without Saving........................................................................43
Updating the BIOS.........................................................................44
Chapter 4
Using the Motherboard Software 45
About the Software DV D-ROM/CD-ROM......................................45
Auto-installing under W indows XP/V ista/7....................................45
Running Setup...............................................................................46
Ma nual Installation............................................................................48
Utility Software Reference..................................................................48
Chapter 5
Setting Up AMD SB850 RAID Configuration 49
Setting Up a Bootable RAID Array..................................................49
Chapter 6
Setting Up eJIFFY 57
Introduction.......................................................................................57
Installation a nd BIOS Setup..............................................................58
Entering eJIFFY............................................................................................61
Features Icons..........................................................................................62
Usage FAQ................................................................................................63
Chapter 7
T r ouble Shooting 67
Start up problems during asse mbly ....................................................67
Start up problems after prolong use..................................................68
Maintena nce a nd care ti ps..................................................................68
Basic Troubleshooting Flowchart......................................................69
45 45
45
45 45
49 49
49
49 49
57 57
57
57 57
67 67
67
67 67
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the A890GXM-A motherboard. This motherboard is a high
performance, enhanced function motherboard that supports socket for AMD
PhenomTM II/AthlonTM II/SempronTM processors (socket AM3) for high-end business
or personal desktop markets.
The motherboard incorporates the AMD 890GX Northbridge (NB) and SB850
Southbridge (SB) chipsets. The Northbridge supports the HyperTransport
terface. The memory controller supports DDR3 memory DIMM frequencies of 1600
(OC)/1333/1066/800*1. It supports four DDR3 slots with maximum memory size of
32 GB*2. Two PCI Express x16 slot, intended for Graphics Interface, are fully compliant to the PCI Express Gen2 (version 2.0). In addition, two PCI Express x1 slots
are supported and one PCI Express x4 slot which is PCI v2.0 compliant is supported.
The SB850 Southbridge supports one PCI slot which is PCI v2.3 compliant. It
integrates USB 2.0 interface, supporting up to fourteen functional ports (six USB
ports and four USB 2.0 headers support additional eight USB ports). The Southbridge
integrates a Serial ATA host controller, supporting five SATA ports with maximum
transfer rate up to 6 Gb/s each.
There is an advanced full set of I/O ports in the rear panel, including one VGA port,
one DVI port, one ESATA port, one HDMI port, one Display port, six USB ports, two
LAN ports, one optical SPDIFO port and audio jacks for microphone, line-in and 8ch line-out.
TM
3.0 in-
1
*1. Due to the limitation of AMD CPU spec, please refer to Memory QVL
for more information.
*2. Due to the DRAM maximum size (2 GB per dimm) at present, the
memory maximum size we have tested is 8 GB per dimm.
Introducing the Motherboard
2
Feature
Processor
This motherboard uses a socket AM3 that carries the following features:
TM
• Accommodates AMD Phenom
(socket AM3)
• Supports HyperTransport
HyperTransportTM Technology is a point-to-point link between two devices, it
enables integrated circuits to exchange information at much higher speeds than
currently available interconnect technologies.
II/AthlonTM II/SempronTM processors
TM
(HT) 3.0 interface speeds
Chipset
The AMD 890GX Northbridge (NB) and SB850 Southbridge (SB) chipsets are
based on an innovative and scalable architecture with proven reliability and
performance.
AMD 890GX
(NB)
SB850 (SB)
• One x4 A-Link Express III interface for connection to
an AMD Southbridge. The A-Link Express III is a proprietary interface developed by AMD basing on the PCI
Express technology, with additional NorthbridgeSouthbridge messaging functionalities. It supports the
PCIe Gen 2 transfer rate of 5 GT/s, and is backward
compatible with the A-Link Express II interface.
• Supports two x16 PCI-Express Gen2 graphics link
• Fully supports ACPI states S1, S3, S4 and S5
• Supports ATI HyperMemory*.
Note: Includes dedicated and shared memory. The amount
of HyperMemory available is determined by various
factors. For details, please consult your AMD CSS
representative.
• Supports 16-bit up/down HyperTransport (HT) 3.0 interface up to 4.8 GT/s.
• Compliant with PCI 2.3 specification at 33 MHz
• Two-la ne PCI Express® (PCIe®) 2.0 interfa ce, supporting up to two general purpose devices. Supported
configurations include: § 1x2 § 2x1
• Supports five Serial ATA devices which speeds up to
6 Gb/s
• Integrated USB 2.0 Host Controller supporting up to
fourteen USB 2.0 ports
• Supports integrated RAID 0, RAID 1, RAID 5, and RAID
10 functionality across all 5 ports (RAID 10 requires
use of 4 or more SATA ports, and RAID 5 require s use
of 3 or more SATA ports)
Memory
• Supports DDR3 1600 (OC)/1333/1066/800 DDR3 SDRAM with Dual-
channel architecture
• Accommodates four unbuffered DIMMs
• Up to 8 GB per DIMM with maxi mum memory size up to 32 GB
Introducing the Motherboard
Audio
• 7.1+2 Channel High Definition Audio Codec
• Meets Microsoft WLP3.x (Windows Logo Program) audio requirements
• All DACs supports 44.1k/48k/96k/192kHz sample rate
• Software selectable 2.5V/3.2V/4.0V VREFOUT
• Direct Sound 3D. compatible
• Power Support: Digital: 3.3V; Analog: 5.0V
Onboard LAN
• Supports PCI Express
• Integrated 10/100/1000 transceiver
• Wake-on-LAN and remote wake-up support
TM
2.0
Expansion Options
The motherboard comes with the following expansion options:
• Two PCI Express x16 slots for Graphics Interface
• One PCI Express x4 slot(the PCI-e x16 slot with blue color)
• Two PCI Express x1 slots
• One 32-bit PCI v2.3 compliant slot
• Five 7-pin SATA connectors
This motherboard supports Ultra DMA bus mastering with transfer rates of
133/100/66/33 MB/s.
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
• One VGA port
• One DVI port
• One ESATA port
• One HDMI port
• One Display port
• Six USB ports
• Two LAN ports
• One optical SPDIFO port
• Audio jacks for microphone, line-in and 8-ch line-out
BIOS Firmware
The motherboard uses AMI BIOS that enables users to configure many system features including the following:
• Power management
• Wake-up alarms
• CPU parameters
• CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
1. Some hardware specifications and software items are subject to change
without prior notice.
2. Due to chipset limitation, we recommend that motherboard be operated in
the ambiance between 0 and 50°C.
Introducing the Motherboard
3
4
Specifications
TM
CPU
• AMD Phenom
AM3)
• Supports “Hyper-Threading” technology CPU
II/AthlonTM II/SempronTM processors (socket
Chipset
Memory
Expansion
Slots
Storage
Audio
LAN
Rear Panel I/O
Internal I/O
Connectors &
Headers
System BIOS
Form Factor • ATX Size, 305mm x 244mm
• NB: AMD 890GX SB: SB850
• Dual-channel DDR3 memory architecture
• 4 x 240-pin DDR3 DIMM sockets support up to 32 GB
• Supports DDR3 1600 (OC)/1333/1066/800 DDR3 SDRAM
•
2 x PCI Express Gen2 x16 slots
• 1 x PCI Express x4 slot(the blue PCI Express x16 is bandwidth of x4)
• 2 x PCI Express x1 slots
• 1 x PCI slot
• Supported by AMD SB850 Express Chipset
• 5 x Serial ATA 6.0 Gb/s Host Controllers
• Supports RAID 0, 1, 5 and 10
• ALC892 8-Channel
• Dual Realtek 811 1DL PCIE GigaLAN Controller
• 1 x VGA port
• 1 x DVI port
• 1 x ESATA port
• 1 x HDMI port
• 1 x Display port
• 6 x USB ports
• 2 x RJ45 LAN connectors
• 1 x Audio port (Line in, microphone in, line out, and optical
SPDIF out)
• 1 x 24-pin ATX Power Supply connector & ATX4P connector
& ATX8P connector .
• 5 x Serial ATA connectors
• 4 x USB 2.0 headers support additional 8 USB ports
• 1 x Front panel header
• 1 x Chassis Intrusion Detect header
• 1 x SPDIF out header
• 1 x Front panel audio header
• 1 x Speaker header
• 1 x Reset button
• 1 x Power button
• CPU_FAN/SYS_F AN/PW R_FAN connectors
• AMI BIOS with 8Mb SPI ROM
• Supports Plug and Play 1.0A, APM 1.2, Multi Boot, DMI
• Supports ACPI revision 1.0 specification
Introducing the Motherboard
Motherboard Components
5
The above image is for reference only; please take the actual
motherboard for detailed parts.
Introducing the Motherboard
6
Table of Motherboard Components
LABEL COMPONENTS
1. CPU Socket
2. CPU_FAN
3. DDR3_1~4
4. ATX_POW ER
5. PWR_FAN
6. CASE
7. SATA1~5
8. SPK
9. SPI_DEBUG
10. F_PANEL
11. PWR_BTN
12. RST_BTN
13. F_USB1~4
14. SYS_FAN
15. SPDIFO
16. F_AUDIO
17. PCI
18. PCIE16X_T
19. PCIE16X_S
20. PCIE1~2
21. PCIEX16
22. ATX4P
23. ATX12V 8-pin +12V power connector
Socket for AMD Phenom
CPU cooling fan connector
240-pin DDR3 SDRAM slots
Standard 24-pin ATX power connector
Power cooling fan connector
CASE open header
Serial ATA connectors
Speaker header
SPI debug header-for factory use only
Front panel switch/LED header
Power on button
Reset button
Front Panel USB headers
System cooling fan connector
SPDIF out header
Front panel audio header
32-bit add-on card slot
PCI Express x4 slot
PCI Express x16 slot for graphics interface
PCI Express x1 slots
PCI Express x16 slot for graphics interface
4-pin ATX power connector
TM
II processor (socket AM3)
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
• Follow these safety precautions when installing the motherboard
• Wear a grounding strap attached to a grounded device to avoid damage from static electricity
• Discharge static electricity by touching the metal case of a safely
grounded object before working on the motherboard
• Leave components in the static-proof bags they came in
• Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies
with the specifications for the ATX system case. Some features on the motherboard
are implemented by cabling connectors on the motherboard to indicators and switches
on the system case. Make sure that your case supports all the features required. Make
sure that your case has sufficient power and space for all drives that you intend to
install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the
motherboard.
This motherboard carries an ATX form factor of 305 X 244 mm. Choose a case that
accommodates this form factor.
7
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in
a case.
Most system cases have mounting brackets installed in the case, which correspond
the holes in the motherboard. Place the motherboard over the mounting brackets
and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion
slots on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes
across the motherboard, you may cause serious damage to the motherboard
or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.
Installing the Motherboard
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system
bus frequency for the processor. You may be able to change these settings by making
changes to jumpers on the motherboard, or changing the settings in the system Setup
Utility. We strongly recommend that you do not over-clock processors or other
components to run faster than their rated speed.
Warning:
1. Over-clocking components can adversely affect the reliability of the
system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components
that are run beyond the rated limits.
2. Always remove the AC power by unplugging the power cord from the
power outlet before installing or removing the motherboard or other hardware components.
This motherboard has a socket AM3 processor socket. When choosing a processor,
consider the performance requirements of the system. Performance is based on the
processor design, the clock speed and system bus frequency of the processor, and the
quantity of internal cache memory and external cache memory.
9
Installing the Motherboard
10
CPU Installation Procedure
The following illustration shows CPU installation components.
1 Install your CPU. Pull up the lever away from
the socket and lift up to 90-degree angle.
2 Locate the CPU cut edge (the corner with
the pin hold noticeably missing). Align and
insert the CPU correctly.
3 Press the lever down and apply thermal
grease on top of the CPU.
4 Put the CPU Fan down on the retention mod-
ule and snap the four retention legs of the
cooling fan into place.
5 Flip the levers over to lock the heat sink in
place and connect the CPU cooling Fan power
cable to the CPUFAN connector. This completes the installation.
To achieve better airflow rates and heat dissipation, we suggest that you
use a high quality fan with 4800 rpm at least. CPU fan and heatsink
installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.
Installing Memory Modules
This motherboard accommodates four memory modules. It can support four 240-pin
DDR3 1600 (OC)/1333/1066/800 . The total memory capacity is 32 GB .
DDR3 SDRAM memory module table
Memory module Memory Bus
DDR3 800 400 MHz
DDR3 1066 533 MHz
DDR3 1333 667 MHz
DDR3 1600 800 MHz
You must install at least one module in any of the four slots. Each module can be
installed with 8 GB of memory.
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always
wear a grounding strap when you handle the modules.
1. Due to the limitation of AMD CPU spec, please refer to Memory QVL
*
for more information.
Installing the Motherboard
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR3 SDRAM only.
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to
the edges of the DIMM.
6 Install any remaining DIMM modules.
* For reference only
11
For best performance and compatibility, we recommend that users install
DIMMs in the sequence of DIMM3, DIMM4, DIMM1 and DIMM2.
Installing the Motherboard
12
Ta ble A: DDR3 (memory module) QVL (Qualified V endor List)
The following DDR3 memory modules have been tested and qualified for use with this
motherboard.
Type
DDR3 1066
Size Vendor Module Name
Hy nix HMT112U6A F P 8C- G7N0 A A
Kingston KVR1066D3N7
1 GB
2 GB
1 GBDDR3 1333
Micron MT8JTF12864AZ-1G1F1
Ramaxel RMR1810NA48E7F-1066-LF
M2Y2G64CB8HC9N-BE
Elixir
Kingston KVR1066D3N7/4G 9905403- 028.A 00LF
Micron
Samsung M378B5673DZ1-CF 8 0842
A-data AD3U1333B1G9-B
Apacer 78.01GC6.9L0
Elixir EBJ10UE8BDF0-DJ-F
Hy nix HMT112U6A F P 8C- H9N0 AA
KingMax
Micron
PSC AL7F8G73D-DG1
Ramaxel
Samsung M378B2873EH1-CH9
Silicon
Power
M2Y2G64CB8HC5N-BE
M 2Y2G64CB8HA9N-BE 0922.TW
MT16JTF25664AZ-1G1F1
MT16JTF25664AY-1G1D1
FLFD45F-B8KG9 NAES
FLFD45F-B8KG9 NAUS
MT8JTF12864AY-1G4D1
MT8JTF12864AZ-1G4F1
RMR1810E7F-1333
RMR1810KD48E7F-1333
SP001GBLTU133S01
Installing the Motherboard
Ta ble B: DDR3 (memory module) QVL (Qualified V endor List)
The following DDR3 memory modules have been tested and qualified for use with this
motherboard.
13
Type
DDR3 1333
DDR3 1600
DDR3 1800
DDR3 2133 1 GB
DDR3 2200
Size
2 GB
4 GB
1 GB
2 GB
1 GB
2 GB
Vendor Module Name
A-data AD3U1333B2G9-B
Apacer 78.A1GC6.9L1
M 2F2G64CB 8HA4N-CG 0903.TW
Elixir
G.SKILL
Hy nix HM T125U6A FP8C-H9N0 AA
KingMax
Kingston KVR1333D3N9/2G 9905403-011. A03LF
Micron MT16JTF25664AY-1G4D1
Nany a NT2GC64B8HAONF-CG 0917.TW
PSC AL8F8G73D-DG1
Ramaxel RMR186EA48D8F-1333
Samsung M378B5673EH1-CH9
Silicon
Power
Kingston KVR1333D3N9
KingMax FLGD45F-B8KG9 NEE S
A - data Fast Dragon
Elixir M 2Y2G64CB8HA9N-DG 0928.TWr
G.SKILL
KingMax F L GE85F- B 8K G9 NEES
Kingston KHX1800C9D3K3/ 3GX 9905402- 04 6.A 01LF
Kingston KHX2133C9D3T1K2
G.SKILL F3-17600CL7D-4GBPIS
M2Y2G64CB8HC9N-CG
EBJ21UE8BDF0-DJ-F/J1108BDSE-DJ-F
M 2Y2G64CB8HA9N-CG 0920.T W
F3-10666CL9D-4GBRL
F3-10666CL8D-4GBECO
F3-10666CL9D-4GBNQ
FLFE85F-B8KG9 NEES
FLFE85F-B8KG9 NEUS
SP002GBLTU133S01
F3-12800CL9D-4GBNQ
F3-12800CL9D-4GBECO
F3-12800CL7D-4GBECO
F3-12800CL9D-4GBRL
Installing the Motherboard
14
Expansion Slots
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect
them to the system bus. Expansion slots are a means of adding or enhancing the
motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are
not part of the basic system.
PCIE1~2 Slots
PCIEX16/
PCIE16X_S
Slots
PCIE16X_T
Slot
(PCIEX4 Slot)
PCI Slot
The PCI Express x1 slots are fully compliant to the PCI
Express Gen2 (version 2.0).
The PCI Express x16 slot is used to install an external PCI
Express graphics card that is fully compliant to the PCI
Express Gen2 (version 2.0).
The PCI Express x4 slot is fully compliant to the PCI Express Base Specification revision 2.0.
This motherboard is equipped with three standard PCI slots.
PCI stands for Peripheral Component Interconnect and is a
bus standard for expansion cards, which for the most part, is
a supplement of the older ISA bus standard. The PCI slots on
this board are PCI v2.3 compliant.
Before installing an add-on card, check the documentation
for the card carefully. If the card is not Plug and Play, you
may have to manually configure the card before installation.
Installing the Motherboard
Follow these instructions to install an add-on card:
1 Remove a blanking plate from the system case corresponding to the
slot you are going to use.
2 Install the edge connector of the add-on card into the expansion slot.
Ensure that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
* For reference only
Notice to User:
1. When use some add-on cards on this motherboard, please install the required
driver and software first.
2. Graphics outputs matrix as follows:
Ex: using DP, user can use HDMI or DVI or D-Sub at the same time.
15
DP HDMI DVI D-Sub
DP O
HDMI O X O
DVI O X O
D-Sub O
Note:
1. Only two graphics outputs (DP,HDMI,DVI,D-Sub) can be displayed at the same
time
2. DVI and HDMI share the same signal, so they can not be used at the same time.
3. Display port and the first PCI E X16 slot (the closest to CPU) share the same
signal, so they can not be used at the same time.
4. The first PCI E X16 slot (the closest to CPU) only supports PCI E X16 Cards.
O
O
O
O
Installing the Motherboard
16
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional
devices:
SAT A1~5: Seri al A T A connectors
These connectors are used to support the new Serial ATA devices for the highest data
transfer rates (6.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
Pin Signal Name
1 Ground 2 TX+
3 TX- 4 Ground
5 RX- 6 RX+
7 Ground - -
Pin Signal Name
SPDIFO: SPDIF out header
This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface)
output to digital multimedia device through optical fiber or coaxial connector.
Pin Signal Name Function
1 SPDIF SPDIF digital output
2 +5VA 5V analog Power
3 Key No pin
4 GND Ground
Installing the Motherboard
F_USB1~4: Front Panel USB headers
The motherboard has six USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have
this kind of case, use auxiliary USB connector to connect the front-mounted ports to
the motherboard.
17
Pin Signal Name
Function
1 USBPWR Front Panel USB Power
2 USBPWR Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground
9 Key No pin
10 USB_FP_OC0 Overcurrent signal
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or system
hang-up.
F_AUDIO: Front Panel Audio header
This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.
Pin Signal Name
Pin Signal Name Function
1 PORT 1L 2 AUD_GND
3 PORT 1R 4 PRESENCE#
5 PORT 2R 6 SENSE1_RETURN
7 SENSE_SEND 8 KE Y
9 PORT 2L 10 SENSE2_RETURN
Pin Signal Name
CASE: Chassis Intrusion Detect Header
This detects if the chassis cover has been removed. This function needs a chassis
equipped with instrusion detection switch and needs to be enabled in BIOS.
Pin 1-2 Function
Short Chassis cover is removed
Open Chassis cover is closed
Installing the Motherboard
18
Installing a SATA Hard Drive
This section describes how to install a SATA hard drive.
About SAT A Connectors
Your motherboard features five SATA connectors supporting a total of four drives.
SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors
are well designed and will only fit in one orientation. Locate the SATA connectors on
the motherboard and follow the illustration below to install the SATA hard drives.
Installing Serial AT A Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the
Serial ATA protocol. This SATA cable comes with an SATA power cable. You can
connect either end of the SATA cable to the SATA hard drive or the connector on the
motherboard.
SATA cable
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard.
2 Attach the other cable end to the SATA hard drive.
3 Attach the SATA power cable to the SATA hard drive and connect the
other end to the power supply.
(optional)
SATA power cable (optional)
for reference only
This motherboard supports the “Hot-Plug” function.
Installing the Motherboard
Connecting I/O Devices
The backplane of the motherboard has the following I/O ports:
VGA Port Connect your monitor to the VGA port.
DVI Port Use the DVI port to connect the monitor.
19
DIS Port(Dispaly
Port)
HDMI Port Connect the HDMI port to the HDMI devices.
CLR_COMS_BTN Use the CLR_CMOS button to clear CMOS.
USB Ports Use the USB ports to connect USB devices.
LAN Port Connect an RJ-45 jack to the LAN port to connect your
computer to the network.
ESATA Port
Optical SPDIF
Output
Audio Ports Use the audio jacks to connect audio devices. The C port is
Use the Display port to connect the monitor.
Use this port to connect to external SATA boxes or Serial
ATA port multipliers.
Before connecting the eSATA cables, make sure to turn off
the power of the external enclosure.
This jack connects to external optical digital audio output
devices.
for stereo line-in signal, while the E port is for microphone
in signal. This motherboard supports audio devices that correspond to the A, B and D port respectively. In addition, all
of the 3 ports, B, and D provide users with both right & left
channels individually. Users please refer to the following
note for specific port function definition.
A: Center & Woofer D: Front Out
B: Back Surround E: Mic_in Rear
C: Line-in -
The above port definition can be changed to audio input or
audio output by changing the driver utility setting.
Installing the Motherboard
Loading...