ECS A785GM-AD3, A880GM-A3 User manual User Manual

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 1.0B

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. AMD, Phenom, Athlon, Sempron and Duron are registered trademarks of AMD

Corporation. Other product names used in this manual are the properties of their respective

owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interferencecausing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1 Introducing the Motherboard

Describes features of the motherboard.

page 1

Go to

Chapter 2 Installing the Motherboard

Chapter 3 Using BIOS

Chapter 4 Using the Motherboard Software

Chapter 5

Hybrid Graphics Support

Chapter 6 Setting Up AMD SB710 RAID Con-

figuration

Chatper 7 Setting Up eJIFFY

Chatper 8 Trouble Shooting

Technology

Provides basic trouble shooting tips

Preface

Describes installation of motherboard components.

Go to Provides information on using the BIOS

Setup Utility. Go to

Describes the motherboard software Go to

Describes the Hybrid Graphics® Technol ogy

Go to

Describes the AMD SB710 RAID Configuration

Go to

Describes the eJIFFY setting up Go to

page 7

page 27

page 45

page 49

page 53

page 61

page 79Go to

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

ABLE OF CONTENTSABLE OF CONTENTS

Preface i

Chapter 1 1

Introducing the Motherboard 1

Introduction............................................................................................1

Feature.....................................................................................................2

Specifications.........................................................................................5

Motherboard Components...................................................................6

iii

Chapter 2

Installing the Motherboard 7

Safety Precautions...............................................................................7

Choosing a Computer Case..................................................................7

Installing the Motherboard in a Case.................................................7

Checking Jumper Settings....................................................................8

Setting Jumpers...............................................................................8

Checking Jumper Settings...............................................................9

Jumper Settings...............................................................................9

Installing Hardware...........................................................................10

Installing the Processor.................................................................10

Installing Memory Modules...........................................................11

Expansion Slots.............................................................................15

Connecting Optional Devices........................................................17

Installing a Hard Disk Drive/CD-ROM/SAT A Hard Drive............20

Installing a Floppy Diskette Drive................................................21

Connecting I/O Devices......................................................................22

Connecting Case Components...........................................................23

Front Panel Header.......................................................................25

Chapter 3

Using BIOS 27

About the Setup Utility ....................................................................27

The Standard Configuration..........................................................27

Entering the Setup Utility...............................................................27

Resetting the Default CMOS V alues...............................................28

Using BIOS............................................................................................29

Standard CMOS Setup..................................................................30

Adva nced Setup.............................................................................32

Advanced Chipset Setup................................................................33

27 27

Integrated Peripherals.................................................................34

Power Ma nagement Setup.............................................................35

PCI/PnP Setup..............................................................................36

PC Health Status..........................................................................37

M.I.B.II (MB Intelligent BIOS II).................................................39

Load Default Settings....................................................................42

Supervisor Passwor d.....................................................................42

User Password..............................................................................43

Save & Exit Setup .........................................................................43

Exit Without Saving.......................................................................43

Updating the BIOS........................................................................44

Chapter 4

Using the Motherboard Software 45

About the Software D V D-ROM/CD-ROM.................................45

Auto-installing under W indows XP/V ista/7...............................45

Running Setup...............................................................................46

Ma nual Installation......................................................................48

Utility Software Reference............................................................48

Chapter 5

Hybrid Graphics® T e chnology Support 49

Hybrid Gra phics® T echnology.....................................................49

Chapter 6

Setting Up AMD SB710 RAID Configuration 53

Setting Up a Bootable RAID Array ................................................53

Chapter 7

Setting Up eJIFFY 61

Introduction....................................................................................61

Installation and BIOS Setup..............................................................62

Entering eJIFFY

Features Icons..............................................................................................66

Usage FAQ...................................................................................................67

..........................................................................................65

45 45

49 49

53 53

61 61

Chapter 8

T r ouble Shooting 79

Start up problems during a ssembly ..................................................79

Start up problems after prolong use................................................79

Maintena nce a nd care ti ps.................................................................80

Basic Troubleshooting Flowchart....................................................81

79 79

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the A785GM-AD3 motherboard. This motherboard is a high performance, enhanced function motherboard that supports socket for AM3 Phenom II/AthlonTM II/ SempronTM processors for high-end business or personal desktop markets.

The motherboard incorporate Southbridge (SB) chipsets. The Northbridge supports the HyperTransport terface. The memory controller supports DDR3 memory DIMM frequencies of 1600/1333/1066/800*1. It supports four DDR3 slots with maximum memory size of 32 GB*2. One PCI Express x16 slot, intended for Graphics Interface, are fully compliant to the PCI Express (version 2.0). In addition, two PCI Express x1 slots are supported.

The SB710 Southbridge supports three PCI slot which is PCI v2.3 compliant. It integrates USB 2.0 interface, supporting up to twelve functional ports (six USB ports and three USB 2.0 headers support additional six USB ports). One onboard IDE connector supports two IDE device integrates a Serial ATA host controller, supporting five SATA ports with maximum transfer rate up to 3.0 Gb/s each. It provides AMD SATA RAID configuration with RAID 0, 1 and 10 modes supported.

There is an advanced full set of I/O ports in the rear panel, including one DVI port, one VGA port, one LAN port, one eSATA port, one optical SPDIFO port, six USB ports,

nd audio jacks for microphone, line-in and 8-channel line-out.

a In addition, this motherboard comes with a power on button, a reset button and a

CLR_CMOS button. The processor can be overclocked when CPU Over-clocking

Func. is set to Enabled in M.I.B.II (MB Intelligent BIOS II).

*1(Due to AMD CPU spec limitation, please refer to Memory QVL for more information)

*2(Due to the DRAM maximum size is 4GB at present, the memory maximum size we have tested is 8GB)

s the AMD 785G Northbridge (NB) and SB710

s in Ultra ATA 133/100/66 modes. The Southbridge

3.0 in-

Introducing the Motherboard

Feature

Processor

This motherboard uses a socket AM3 that carries the following features:

• Accommodates AM3 Phenom

• Supports HyperTransport

• Support transfer rate up to 5200 mega-transfers per second

HyperTransportTM Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.

This board supports CPU up to 95W TDP only; you can refer to AMD website to check your CPU.

II/AthlonTM II/ SempronTM processors

(HT) 3.0 interface speeds

Chipset

The AMD 785G Northbridge (NB) and SB710 Southbridge (SB) chipsets are based on an innovative and scalable architecture with proven reliability and performance.

AMD 785G (NB)

• One x4 A-Link Express II interface for connection to an AMD Southbridge

• Supports PCIe (version 2.0)

• Proven Radeon

• Enhanced Digital Display integration

• Fully ACPI 2.0 and IAPC (In stantly Availa ble PC) power management

• Single chip solution in 55nm, 1.1 V CMOS technology

• Integrated ATI Hybrid CrossFire™, ATI AvivoTM HD1, AMD Cool'n'QuietTM, ATI SurroundViewTM, AMD OverDrive and AMD PowerNow!

graphics powering DirectX® 10.1

SB710 (SB)

• Compliant with PCI 2.3 specification at 33 MHz

• Supports five Serial ATA devices which speeds up to 3.0 Gb/s

• Integrated USB 2.0 Host Controller supporting up to twelve USB 2.0 ports

• Integrated IDE controller supports Ultra AT A 133/100/ 66 modes

• Supports integrated RAID0, RAID1, and RAID 10 (requires use of 4 or more SATA ports) functionalities across all 5 ports

Memory

• Supports DDR3 1600/1333/1066/800 DDR3 SDRAM with Dual-channel architecture

• Accommodates four unbuffered DIMMs

• 4 x 240-pin DDR3 DIMM sockets support up to 32 GB

Introducing the Motherboard

Audio

• All DACs support 192K/96K/48K/44.1KHz DAC sample rate

• High-quality analogy differential CD input

• Software selectable 2.5V/3.75V VREFOUT

• Meets Microsoft WLP3.10 audio requirements

• Direct Sound 3DTM compatible

Onboard LAN

• Onboard PCI-Express LAN controller

• Supports 10/100/1000 Mbit Ethernet (optional 10/100 Ethernet only available)

• Support Wake-on-LAN and remote wake-up

Expansion Options

The motherboard comes with the following expansion options:

• One PCI Express x16 slot for Graphics Interface

• Two PCI Express x1 slots

• Three 32-bit PCI v2.3 compliant slots

• One IDE connector supporting up to two IDE devices

• Five 7-pin SATA connectors

This motherboard supports Ultra DMA bus mastering with transfer rates of 133 /100/66 MB/s.

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• One PS/2 Keyboard & PS/2 mouse

• One DVI port

• One VGA port

• One LAN port

• One eSATA port

• One optical SPDIFO port

• Six USB ports

• Audio jacks for microphone, line-in, 8-channel line out and Optical SPDIF Out

Introducing the Motherboard

BIOS Firmware

The motherboard uses AMI BIOS that enables users to configure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different processor clock speeds. And it is available to adjust the voltages of the CPU, NB and SB.

1. Some hardware specifications and software items are subject to change without prior notice.

2. Due to chipset limitation, we recommend that motherboard be operated in the ambiance between 0 and 50°C.

Introducing the Motherboard

Specifications

CPU

Chipset Memory

Expansion Slots

Storage

Audio LAN

Rear Panel I/O

Internal I/O Connectors & Headers

• AM3 socket for PhenomTM II/AthlonTM II/ SempronTM proces-

• Supports “Hyper-Threading” technology CPU

• Support transfer rate up to 5200 mega-transfers per sec-

• AMD 785G & AMD SB710

• Dual-channel DDR3 1600 memory architecture

• 4 x 240-pin DDR3 DIMM sockets support up to 32 GB

• Supports DDR3 1600/1333/1066/800 DDR3 SDRAM

• 1 x PCI Express x16 slot

• 2 x PCI Express x1 slots

• 3 x PCI slots

• Supported by AMD SB710 Express Chipset

• 5 x Serial ATA 3.0 Gb/s Host Controllers

• Supports RAID 0, 1, and 10

• 2 x Ultra DMA133/100/66 devices

• 1 x eSATA 3.0 Gb/s device

• ALC888S 8-ch HD audio

• Realtek8111DL GigaLAN Controller (Colay RTL8103EL 10/

• 1 x PS/2 keyboard & PS/2 mouse connector

• 6 x USB ports

• 1 x DVI port

• 1 x VGA port

• 1 x eSATA port

• 1 x RJ45 LAN connector

• 1 x Optical SPDIFO port

• 1 x Audio port (1x Line in, 4x Line out, 1x Optical SPDIF Out)

• 24-pin ATX Power Supply connector, 4-pin 12V connector

• 1 x CPU_FAN

• 1 x SYS_FAN

• 1 x NB_F AN

• 5 x SATA 3Gb/s connectors

• 3 x USB 2.0 headers support additional 6 USB ports

• 1 x Front panel header

• 1 x Chassis Intrusion Detect header

• 1 x Front panel audio header

• 1 x Speaker header

• 1 x CD in header

• 1 x Power on button

• 1 x Clear CMOS button • 1 x Power on LED (Green Light)

• 1 x Reset button • 1 x Stand by LED (Red Light)

sors

ond

100 LAN Controller

System BIOS

Form Factor • ATX Size, 305mm x 220mm

• AMI BIOS with 8Mb SPI ROM

• Supports Plug and Play 1.0A, APM 1.2, Multi Boot, DMI

• Supports ACPI revision 3.0 specification

Introducing the Motherboard

Motherboard Components

Table of Motherboard Components

LABEL COMPONENTS

1. CPU Socket

2. CPU_FAN

3. DDR3_1~4

4. ATX_POWER

5. IDE

6. SPK

7. CASE

8. SATA1~6

9. PWR_BTN

10. F_PANEL

11. RST_BTN

12. F_USB1~3

13. USBPWR_F1~2

14. COM

15. CLR_CMOS_BTN

16. CD_IN

17. F_AUDIO

18. PCI1~3

19. PCIEX16

20. PCIE1~2

21. SYS_FAN

Socket for AM3 Phenom processors

CPU cooling fan connector 240-pin DDR3 SDRAM slots Standard 24 Primar S

eaker header Chassis detector header Serial ATA connectors Power on button Front panel switch/LED header Reset button Front panel USB headers Front panel USB power select jumpers Onboard serial port header Clear CMOS button Analog audio input connector Front panel audio header 32-bit add-on card slots PCI Express x16 slot for graphics interface PCI Express x1 slots System cooling fan connector

in ATX power connector

IDE connector

22. NB_FAN Northbridge cooling fan connector

23. USBPWR_R1~2

24. ATX12

Rear panel USB PS/2 power select jumpers 4-pin +12V power connector

This concludes Chapter 1. The next chapter explains how to install the motherboard.

II/Ath lonTM II/ Sempron

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the ATX system case. Firstly, some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required. Secondly, this motherboard supports one floppy diskette drive and two enhanced IDE drives. Make sure that your case has sufficient power and space for all drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries an ATX form factor of 350 X 220 mm. Choose a case that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT.

SHORT OPEN

Installing the Motherboard

Checking Jumper Settings & Clear CMOS Button

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

Jumper Settings

Jumper

Type Description

Setting (default)

CLR_CMOS_BTN

USBPWR_F1 3-pin

USBPWR_F2

USBPWR_R1

button

3-pin

1. To avoid the system unstability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save & Exit Setup”.

2. Make sure the power supply provides enough 5VSB voltage before selecting the 5VSB function.

3. It is required that users place the USBPWR_F1~2 & USBPWR_R1~2 cap onto 2-3 pin rather than 1-2 pin as default if you want to wake up the computer by USB/PS2 KB/Mouse.

CLEAR CMOS

USB Power Cotroller

NO PUSH: NORMAL PUSH: CLEAR

1-2: VCC5 2-3: 5VSB

1-2: VCC5

2-3: 5VSB

1-2: VCC5

2-3: 5VSB

1-2: VCC5

2-3: 5VSB

Installing the Motherboard

CLR_CMOS_BTN

USBPWR_F1

USBPWR_F2

USBPWR_R1

USBPWR_R2

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change these settings by making changes to jumpers on the motherboard, or changing the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.

Warning:

1. Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

2. Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

This motherboard has a Socket AM3 processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

Fail-Safe Procedures for Over-clocking

When end-users encounter failure after attempting over-clocking, please take the following steps to recover from it.

1. Shut down the computer.

2. Press and hold the “Page Up Key (PgUp)” of the keyboard, and then boot the PC up.

3. Two seconds after the PC boots up, release the “Page Up Key (PgUp)”.

4. The BIOS returns to the default setting by itself.

Installing the Motherboard

CPU Installation Procedure

The following illustration shows CPU installation components.

1 Install your CPU. Pull up the lever away from

the socket and lift up to 90-degree angle.

2 Locate the CPU cut edge (the corner with

the pin hold noticeably missing). Align and insert the CPU correctly.

3 Press the lever down and apply thermal

grease on top of the CPU.

4 Put the CPU Fan down on the retention mod-

ule and snap the four retention legs of the cooling fan into place.

5 Flip the levers over to lock the heat sink in

place and connect the CPU cooling Fan power cable to the CPUFAN connector. This completes the installation.

To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 4800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.

Installing Memory Modules

This motherboard accommodates four memory modules. It can support four 240-pin DDR3 1600/1333/1066/800. The total memory capacity is 32 GB.

DDR3 SDRAM memory module table

Memory module Memory Bus

DDR3 800 400 MHz

DDR3 1066 533 MHz DDR3 1333 667 MHz

DDR3 1600 800 MHz

You must install at least one module in any of the four slots. Each module can be installed with 8 GB of memory.

Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

Installing the Motherboard

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR3 SDRAM only. 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the

notches in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it

seats correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.

6 Install any remaining DIMM modules.

For best performance and compatibility, we recommend that users install DIMMs in the sequence of DIMM3, DIMM4, DIMM1 and DIMM2.

Recommend configuration for best performance and compatibility

Numb e r o f DIMMs DIMM 1 DIMM 2 DIMM 3 DIMM 4 AM 2 AM 2 + *

1 2 3 4

Single Channel

Dual Channel

Single Channel

Dual Channel

Unganged Mode

Ganged Mode

Unganged Mode

Ganged Mode

: operation with normal performance : operation with the best performance

Installing the Motherboard

Table A: DDR3 (memory module) QVL (Qualified Vendor List)

The following DDR3 2100/1800/1600/1333/1066 memory modules have been tested and qualified for use with this motherboard.

Type Size Vendor Module Name

512

1 GB

DDR3 1066

2 GB

4 GB

E LPIDA P C3-8500U-7-00-AP

Hynix

Kingston KVR1066D3N7/1G

M icron M T8JTF12864 AZ-1G1F1 Ramaxel RMR 1810NA48E7F -1066-LF Samsung Golden Bar M 378B 2873DZ1-CF8 0818

Elixir

Hynix

Micron

Samsung M378B5673DZ1-CF8 0842 Kingston

HYMT112U64ZNF8-G8 AA

HMT112U6AFP8C-G7N0 AA

M2Y2G64CB8HA9N-BE 0922.TW

M 2Y2G64C B 8HC5N-BE

HYMT125U64ZNF8-G8 AA

HMT125U6AFP8C-G7N0 AA

MT16JTF25664AZ-1G1F1 M T16JTF25664AY-1G1D1

KVR1066D3N7/4G 9905403-028.A00LF

Installing the Motherboard

Table B: DDR3 (memory module) QVL (Qualified V endor List)

The following DDR3 2100/1800/1600/1333/1066 memory modules have been tested and qualified for use with this motherboard.

Type Size Vendor Module Name

A-data AD3U1333B1G9-B

Apacer 78.01GC6.9L0

Hynix HMT112U6AFP8C-H9N0 AA

FLFD45F-B8KG9 NAES

FLFD45F-B8KG9 N AU S

M378B2873DZ1-CH9 M378B2873E H1-CH9

M2F2G64CB8HA4N-CG 0903.TW

M2Y2G64CB8H A9N -CG 0920.TW

FLFE 85F-B8KG9 NEE S FLFE 85F-B8KG9 NEUS

Kingston/KVR1333D3N9/2G

KVR1333D3N9/2G 9905403-011.A03LF

MT16JTF25664AY-1G4D1

MT8JTF12864AZ-1G4F1

DDR3 1333

2 GB

1 GB

DDR3 1600

2 GB

DDR3 1800 1 GB DDR3 2133 2 GB

KingMax

Kingston KVR1333D3N9/1G

Micron MT8JTF12864AY-1G4D1

PSC AL7F8G73D-DG1

Ramaxel RM R1810KD48E7F-1333

Samsung

Silicon Power SP001G BLTU133S01

A-data AD3U1333B2G9-B

Apacer 78.A1GC6.9L1

Elixir

Hynix HMT125U6AFP8C-H9N0 AA

KingMax

Kingston

Mic r on

PSC AL8F8G73D-DG1

Samsung M378B5673EH1-CH9

Silicon Power SP002G BLTU133S01

KingMax FLGD45F-B8KG9 NEES

Elixir M2Y2G64CB8H A9N -DG 0928.TWr

KingMax FLGE 85F-B8KG9 NEE S Kingston KHX1800C9D3K3/3GX 9905402-046.A01LF Kingston KHX2133C9D3T 1K2/4GX

Installing the Motherboard

Expansion Slots

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

PCIE1~2 Slots

PCIEX16 Slot

PCI1~3 Slots

The PCI Express x1 slots are fully compliant to the PCI Express Generation 2.0 (version 2.0).

The PCI Express x16 slot is used to install an external PCI Express graphics card that is fully compliant to the PCI Express Generation 2.0 (version 2.0).

This motherboard is equipped with three standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

Installing the Motherboard

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the

slot you are going to use.

2 Install the edge connector of the add-on card into the expansion slot.

Ensure that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

Installing the Motherboard

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

COM: Onboard serial port header

Connect a serial port extension bracket to this header to add a serial port to your system.

Pin Signal Name Function

1 DCDB Data Carrier Detect 2 SINB Serial Input

3 SOUTB UART B Serial Output

4 DTRB UART B Data Terminal Ready 5 GND Ground 6 DSRB Data Set Ready

7 RTSB RART B Request to Send 8 CTSB Clear to Send

9 RI Ring Indicator

10 Key No pin

Installing the Motherboard

SAT A1~5: Serial A T A connectors

These connectors are used to support the new Serial ATA devices for the highest data transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

Pin Signal Name

1 Ground 2 TX+

3 TX- 4 Ground 5 RX- 6 RX+

7 Ground - -

F_AUDIO: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and lineout ports for easier access.

Pin Signal Name Pin Signal Name Function

1 PORT 1L 2 AUD_GND

Pin Signal Name

3 PORT 1R 4 PRESENCE# 5 PORT 2R 6 SENSE1_RETURN

7 SENSE_SEND 8 KE Y

9 PORT 2L 10 SENSE2_RETURN

CD_IN: Analog audio input connector

Pin Signal Name Function

1 CD_L Left CD-in signal

2 GND Ground 3 GND Ground

4 CD_R Right CD-in signal

CASE: Chassis Intrusion Detect Header

This detects if the chassis cover has been removed. This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS.

Pin 1-2 Function

Short Chassis cover is removed

Open Chassis cover is closed

Installing the Motherboard

F_USB1~3: Front Panel USB headers

The motherboard has six USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

Pin Signal Name

1 USBPWR Front Panel USB Power

2 USBPWR Front Panel USB Power

3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal 5 USB_FP_P0+ USB Port 0 Positive Signal

6 USB_FP_P1+ USB Port 1 Positive Signal

7 GND Ground

8 GND Ground

9 Key No pin

10 USB_FP_OC0 Overcurrent signal

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hangup.

Function

Installing the Motherboard

Installing a Hard Disk Drive/CD-ROM/SAT A Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CDROM drive.

About IDE Devices

Your motherboard has one IDE interface. An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.

ou must orient the cable connector so that the pin1 (color) edge of the

Y cable corresponds to the pin 1 of the I/O port connector.

IDE: IDE Connector

This motherboard supports five high data transfer SATA ports with each runs up to

3.0 Gb/s. To get better system performance, we recommend users connect the CDROM to the IDE channel, and set up the hard drives on the SATA ports.

IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.

About SAT A Connectors

Your motherboard features five SATA connectors supporting a total of five drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

Installing Serial A T A Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with an SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

SATA cable (optional)

SATA power cable (optional)

Installing the Motherboard

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the

other end to the power supply.

This motherboard supports the “Hot-Plug” function.

Installing the Motherboard

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

VGA Port Connect your monitor to the VGA port.

DVI Port

USB Ports Use the USB ports to connect USB devices.

ESATA Port

LAN Port Connect an RJ-45 jack to the LAN port to connect your

computer to the network.

Optical SPDIF Output

Audio Ports Use the audio jacks to connect audio devices. The C port is

Connect the DVI port to connect the monitor.

Use this port to connect to an external SATA box or a Serial ATA port multiplier.

This jack connects to external optical digital audio output devices.

for stereo line-in signal, while the E port is for microphone in signal. This motherboard supports audio devices that correspond to the A, B and D port respectively. In addition, all of the 3 ports, B, and D provide users with both right & left channels individually. Users please refer to the following note for specific port function definition.

A: Center & Woofer D: Front Out B: Back Surround E: Mic_in Rear C: Line-in -

The above port definition can be changed to audio input or audio output by changing the driver utility setting.

Installing the Motherboard

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the standard power supply connector to ATX_POWER. 3 Connect the case speaker cable to SPK. 4 Connect the case switches and indicator LEDs to the F_PANEL. 5 Connect the system cooling fan connector to SYS_FAN. 6 Connect the auxiliary case power supply connector to ATX12V1. 7 Connect the northbridge cooling fan connector to NB_FAN.

Connecting 24-pin power cable

Users please note that the 24-pin power cable can be connected to the ATX_POWER connector.

With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX_POWER match perfectly.

24-pin power cable

Installing the Motherboard

Connecting 4-pin power cable

The ATX12V power connector is used to provide power to the CPU.

When installing 4-pin power cable, the latches of power cable and the ATX12V match perfectly.

4-pin power cable

CPU_FAN: Cooling F AN Power Connector

Pin Signal Name

1 GND System Ground 2 +12V Power +12V

3 Sense Sensor

4 PWM CPU FAN control

Users please note that the fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W max.) at +12V.

ATX_POWER: A TX 24-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V

3 Ground 15 COM

4 +5V 16 PS_ON

5 Ground 17 COM

6 +5V 18 COM 7 Ground 19 COM 8 PWRGD 20 -5V

9 +5VSB 21 +5V

10 +12V 22 +5V 11 +12V 23 +5V

12 +3.3V 24 COM

Function

SYS_FAN/NB_F AN: F AN Power Connector

Pin Signal Name Function

1 GND System Ground

2 +12V Power +12V

3 Sense Sensor

Installing the Motherboard

SPK: Internal speaker

Pin Signal Name

1 VCC 2 Key 3 NC 4 Signal

ATX12V1: A TX 12V Power Connector

Pin Signal Name

1 Ground 2 Ground 3 +12V

4 +12V

Front Panel Header

The front panel header (F_PANEL) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:

Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED (+)

3 HD_LED_N Hard disk LED (-)

5 RST_SW_N Reset Switch (-)

7 RST_SW_P Reset Switch (+)

9 RSVD Reserved

* MSG LED (dual color or single color)

2 FP PWR/SLP *MSG LED (+)

4 FP PWR/SLP *MSG LED (-)

6 PWR_SW_P Power Switch (+)

8 PWR_SW_N Power Switch (-)

10 Key No pin

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Installing the Motherboard

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentarycontact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary-contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

This concludes Chapter 2. The next chapter covers the BIOS.

Installing the Motherboard

Chapter 3

Using BIOS

About the Setup Utility

The computer uses the latest “American Megatrends Inc. ” BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Press DEL to enter SETUP

Using BIOS

Press the delete key to access the BIOS Setup Utility.

Standard CMOS Setup

Advanced Setup

Advanced Chipset Setup

Integrated Peripherals

Power Management Setup

PCI/PnP Setup

PC Health Status

: Move F10: Save ESC: Exit

mnlk

F1:General Help

Enter : Select

F9: Default settings

M.I.B.II (MB Intelligent BIOS II)

Load Default Settings Supervisor Password

User Password

Save & Exit Setup Exit Without Saving

+/-/: Value

Resetting the Default CMOS Values

When powering on for the first time, the POST screen may show a “CMOS Settings Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values.

Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message.

Standard CMOS Setup

Advanced Setup

Advanced Chipset Setup

Integrated Peripherals

Power Management Setup

PCI/PnP Setup

PC Health Status

: Move F10: Save ESC: Exit

mnlk

F1:General Help

Load Default Setting?

[Ok] [Cancel]

Enter : Select

F9: Default settings

M.I.B.II (MB Intelligent BIOS II)

Load Default Settings Supervisor Password

User Password

Save & Exit Setup Exit Without Saving

+/-/: Value

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle the values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a triangle

The default BIOS setting for this motherboard applies for most conditions with optimum performance. It is not suggested to change the default values in the BIOS setup and the manufacture takes no responsibility to any damage caused by changing the BIOS settings.

f) lead to submenus that enable you to change

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

ESC Exits the current menu

< >

+/-/ Modifies the selected field’s values

Enter Select

F9 F10 Saves the current configuration and exits setup F1 Displays a screen that describes all key functions

Scrolls through the items on a menu

Load a default optimized setting

Using BIOS

For the purpose of better product maintenance, the manufacture reserves the right to change the BIOS items presented in this manual. The BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual.

Standard CMOS Setup

This option displays basic information about your system.

Date Tue 12/01/2009 Time 00:04:15

IDE Master Not Detected

IDE Slave

SATA1 Not Detected

SA TA 2 Not Detected

SA TA 3 Not Detected

SATA 4 Not Detected

f f

SATA5 Not Detected eSATA Not Detected

IDE BusMaster Enabled

mnlk

Date & Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the

IDE Master/Slave, SATA1~5, eSATA

Windows Date and Time Properties utility.

Your computer has one IDE channel which can be installed with one or two devices (Master and Slave). In addition, this motherboard supports five SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the SATA channel.

Standard CMOS Setup

: Move

Enter : Select

F1: General Help

Not Detected

+/-/: Value

F9: Default settings

IDE Master

Help Item

User [Enter], [TAB] or [SHIFT-T AB] to select a field.

Use [+] or [-] to configure system Date.

F10: Save ESC: Exit

IDE Master

Device : Not Detected

Type Auto

LBA/Large Mode Block (Multi-Sector Transfer)

PIO Mode Auto

DMA Mode Auto

S.M.A.R.T Auto

32Bit Data Transfer Enabled

: Move

mnlk

Enter : Select

F1: General Help

Auto Auto

+/-/: Value

F9: Default settings

Using BIOS

Help Item

Select thd type of device connected to the system

F10: Save ESC: Exit

Type (Auto)

Use this item to configure the type of the IDE device that you specify. if the feature is unabled, it will enhance hard disk performance by reading or writing more data during each transfer.

LBA/Large Mode (Auto)

Use this item to set the LAB/Large mode to enhance hard disk performance by optimizing the area the hard disk is visited each time.

Block (Multi-Sector Transfer) (Auto)

If the feature is enabled, it will enhance hard disk performance by reading or writing more data during each transfer.

PIO Mode (Auto)

Use this item to set the PIO mode to enhance hard disk performance by optimizing the hard disk timing.

DMA Mode (Auto)

DMA capability allows user to improve the transfer-speed and data-integrity for compatible IDE devices.

S.M.A.R.T. (Auto)

The S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T. software resides on both the disk drive and the host computer.

32Bit Data Transfer (Enabled)

Use this item to set the onboard SATA-IDE channel to be disabled, IDE, or RAID.

Press <Esc> to return to the Standard CMOS Setup page.

IDE BusMaster (Enabled)

This item enables or disables the DMA under DOS mode. We recommend you to leave this item at the default value.

Press <Esc> to return to the main menu setting page.

Using BIOS

Advanced Setup

This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.

AMD C&Q Auto Enhanced Halt (CIE) Disabled Quick Power on Self Test Enabled Boot Up Numlock Status ON APIC Mode Enabled 1st Boot Device Hard Drive 2nd Boot Device CD/DVD 3rd Boot Device Removable Dev . Boot Other Device Yes ECS eJIFFY Function Disabled

Advanced Setup

: Move

mnlk

F1:General Help

Enter : Select

F10: Save ESC: Exit+/-/: Value

F9: Default settings

Help Item

Enable/Disable the generation of ACPI_PPC, _PSS, and _PCT objects.

AMD C&Q (Enabled)

This item helps the system to lower the frequency when CPU idles. When the frequency decreases, the temperature will drop automatically as well.

Enhanced Halt (C1E) (Disabled)

This item enables or disables enhanced halt.

Quick Power on Self Test (Enabled)

Enable this item to shorten the power on testing (POST) and have your system start

. You might like to enable this item after you are confident that your system

up faster hardware is operating smoothly.

Boot Up Numlock Status (On)

This item defines if the keyboard Num Lock key is active when your system is started.

APIC Mode (Enabled)

This item allows you to enable or disable the APCI (Advanced Programmable Interrupt Controller) mode.

APIC provides symmetric multi-processing (SMP) for sys-

tems, allowing support for up to 60 processors.

1st/2nd3rd Boot Device (Hard Drive/CD/DVD/Removable Dev.)

Use this item to determine the device order the computer used to look for an operating system to load at start-up time. The devices showed here will be different depending on the exact devices installed on your motherboard.

Using BIOS

Boot Other Device (Yes)

When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second and Third boot devices.

ECS eJIFFY Function (Disabled)

Use this item to enable or disable the ECS eJIFFY Function. eJIFFY is ECS unique software program for the quick access to the internet without entering O.S. Please refer to Chapter7 to know more about eJIFFY

Press <Esc> to return to the main menu setting page.

Advanced Chipset Setup

This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.

Advanced Chipset Setup

Internal Graphics Mode UMA GFX Clock Override Disabled Share Memory Auto Size Auto Init Display First PCI Memory Hole Remapping Enabled HDMI Audio Enabled DCT Unganged Mode Always

Enter : Select

: Move

mnlk

F1:General Help

F9: Default settings

F10: Save ESC: Exit+/-/: Value

Help Item

Options

Disabled UMA

Internal Graphics Mode (UMA)

Use this item to choose the onboard VGA mode. You can select [Disabled] to disablethe onboard VGA, [UMA] to use the system memory.

W arning: If Disabled Internal Graphics Mode, please Loading default toEnable it.

GFX Clock Override (Disabled)

Use this item to enable or disable GFX Clock Override.

Share Memory Size (Auto)

This item lets you allocate a portion of the main memory for the onboard VGA display application.

Using BIOS

Init Display First (PCI)

Use this item to select which graphics controller to use as the primary boot devices.

Memory Hole Remapping (Enabled)

This item allows users to enable or disable memroy hole remapping.

HDMI Audio (Enabled)

This item is used to enable or disable the onboard audio chip.

DCT Unganged Mode (Always)

This item is used to select the DCT mode (DRAM Controller mode). Press <Esc> to return to the main menu setting page.

Integrated Peripherals

This page sets up some parameters for peripheral devices connected to the system.

OnBoard IDE Controller Enabled OnBoard SAT A Mode Enabled SATA Configuration IDE OnBoard AUDIO Function Enabled OnBoard LAN Function Enabled OnBoard LAN Boot ROM Disabled Serial Port1 Address Disabled USB Functions Enabled Legacy USB Support Enabled

Integrated Peripherals

Options

DISABLED: disables the integrated IDE Controller.

Enabled : ensables both Controller.

Help Item

mnlk

: Move

F1:General Help

F9: Default settings

F10: Save ESC: Exit+/-/: Value

Enter : Select

OnBoard IDE Controller (Enabled)

Use this item to enable or disable the onboard IDE interface.

OnBoard SATA Mode (Enabled)

Use this item to enable or disable the onboard SATA mode.

SATA Configuration (IDE)

Use this item to show the Serial ATA Configuration options: Disabled, Compatible, Enhanced.

OnBoard AUDIO Function (Enabled)

Use this item to enable or disable the onboard Audio function.

OnBoard LAN Function (Enabled)

Use this item to enable or disable the onboard LAN function.

OnBoard LAN Boot ROM (Disabled)

Use this item to enable or disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed.

Using BIOS

Serial Port1 Address ( Disabled)

Use this item to enable or disable the onboard COM1 serial port, and to assign a port address.

USB Functions (Enabled)

Use this item to enable or disable the USB function.

Legacy USB Support (Enabled)

Use this item to enable or disable support for legacy USB devices. Setting to Auto allows the system to detect the presence of USB device at startup. If detected, the USB controller legacy mode is enabled. If no USB device is detected, the legacy USB support is disabled.

Press <Esc> to return to the main menu setting page.

Power Management Setup

This page sets up some parameters for system power management operation.

Power Management Setup

ACPI Suspend Type S3 PWRON After PWR-Fail Power Off Resume by Ring Disabled Resume By PCI/PCI-E/Lan PME Disabled Resume by USB (S3) Disabled Resume By PS2 KB (S3) Disabled Resume By PS2 MS (S3) Disabled Resume on RTC Alarm Disabled

Enter : Select

: Move

mnlk

F1:General Help

F9: Default settings

F10: Save ESC: Exit+/-/: Value

Help Item

Select the ACPI state used for System Suspend.

ACPI Suspend Type (S3)

Use this item to define how your system suspends. In the default, S3, the suspend mode is a suspend to RAM, i.e, the system shuts down with the exception of a refresh current to the system memory.

PWRON After PWR-Fail (Power Off)

This item enables your computer to automatically restart or return to its operating status.

Resume By Ring (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem.

You

must use an ATX power supply in order to use this feature.

Using BIOS

Resume By PCI/PCI-E/Lan PME (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the PCI card.

Resume By USB (S3) (Disabled)

This item allows you to enable/disable the USB device wakeup function from S3 mode.

Resume By PS2 KB (S3) (Disabled)

This item enables or disables you to allow keyboard activity to awaken the system from power saving mode.

Resume By PS2 MS (S3) (Disabled)

This item enables or disables you to allow mouse activity to awaken the system from power saving mode.

Resume on RTC Alarm (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume at a fixed time based on the system’s RTC (realtime clock). Use the items below this one to set the date and time of the wake-up alarm. You must use an ATX power supply in order to use this feature.

Press <Esc> to return to the main menu setting page.

PCI / PnP Setup

This page sets up some parameters for devices installed on the PCI bus and those utilizing the system plug and play capability.

Allocate IRQ to PCI VGA Yes

PCI / PnP Setup

Help Item

YES: Assigns IRQ to PCI VGA card if card requests IRQ. NO: Does not assign IRQ to PCI VGA card even if card requests an IRQ.

mnlk

: Move

F1:General Help

F10: Save ESC: Exit+/-/: Value

F9: Default settings

Enter : Select

Allocate IRQ to PCI VGA (Yes)

Use this item to select which graphics controller to use as the primary boot devices.

Press <Esc> to return to the main menu setting page.

Using BIOS

PC Health Status

On motherboards support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.

PC Health Status

-=- System Hardware Monitor-= Smart Fan Function Press Enter

Shutdown Temperature (CPU) Disabled

CPU T emperature : 53°C/127°F

NB Temperature : 55°C/131°F System Temperature : 37°C/98°F

CPU FAN Speed : 4821 RPM CPU Vcore : 1.328V

Vcc NB : 1.200V VDIMM : 1.600V VBAT : 3.216V

Case Open Warning Disabled

Chassis Opened No

Enter : Select

mnlk

Smart Fan Function

: Move

F1:General Help

F10: Save ESC: Exit+/-/: Value

F9: Default settings

Scroll to this item and press <Enter> to view the following screen:

SMART FAN Control Enabled Smart Fan Mode Normal SMART Fan start PWM value 43 SMART Fan start TEMP.(°C) 27 DeltaT1 +3 SMART Fan Slope PWM value 3 PWM value/°C CPU FAN Full Limit Temp 55°C

Help Item

Options

Disabled Enabled

Help Item

mnlk

: Move

F1:General Help

F10: Save ESC: Exit+/-/: Value

F9: Default settings

Enter : Select

SMART FAN Control (Enabled)

This item allows you to enable/disable the control of the system fan speed by changing the fan voltage.

Using BIOS

Smart Fan Mode (Normal)

This item allows you to select the fan mode (Normal, Quiet, Silent, or Manual) for a better operation environment. If you choose Normal mode, the fan speed will be auto adjusted depending on the CPU temperature. If you choose Quite mode, the fan speed will be auto minimized for quiet environment. If you choose Silent mode, the fan speed will be auto restricted to make system more quietly. If you choose Manual mode, the fan speed will be adjust depending on users’ parameters.

SMART Fan start PWM value (43)

This item is used to set the start PWM value of the smart fan.

SMART Fan start TEMP. (°C) (27)

This item is used to set the start temperature of the smart fan.

DeltaT1 (+3)

This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works.

SMART Fan Slope PWM value (3 PWM value/°C)

This item is used to set the Slope Select PWM of the smart fan.

CPU FAN Full Limit Temp. (55°C)

This item is used to set the limit temperature of the smart fan.

Press <Esc> to return to the main menu setting page.

Shutdown Temperature (CPU) (Disabled)

Enable you to set the maximum temperature the CPU can reach before powering down

System Component Characteristics

These items display the monitoring of the overall inboard hardware health events, such as CPU & System & NB temperature, CPU fan speed, CPU Vcore, ...etc.

• CPU Temperature

• NB Temperature

• System Temperature

• CPU FAN Speed

• CPU Vcore

• Vcc NB

• VDIMM

• VBAT

Case Open Warning (Disabled)

This item enables or disables the warning if the case is opened up, and the itembelow indicates the current status of the case.

Chassis Opened (No)

This item indicates whether the case has been opened Press <Esc> to return to the main menu setting page.

Using BIOS

M.I.B. II (MB Intelligent BIOS II)

This page enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

Memory Configuration Press Enter

Advanced Clock Calibration Auto Special ACC Disabled HT Frequency Auto CPU/HT Reference Clock (MHz) 20 0 Auto Detect DIMM/PCI Clk Enabled Spread Spectrum Enabled CPU Voltage Disabled DIMM Voltage Disabled NB Voltage +30mV SB Voltage 1.25 v

AMD Athlon (tm) II X4 630 Processor

Speed : 2800MHz, NB CLK: 2000MHz Current CPU Frequency 2000MHz Current CPU Voltage 1.3250v Current NB Frequency 2000MHz DIMM Voltage Default 1.60v NB Voltage Default 1.15v SB Voltage Default 1.20v

mnlk

F1:General Help

Memory Configuration

M.I.B. II (MB Intelligent BIOS II)

Options

Disabled Auto All Cores Per Core

: Move F10: Save ESC: Exit

Enter : Select

+/-/: Value

F9: Optimized Defaults

Help Item

Scroll to this item and press <Enter> to view the following screen:

Memory Configuration DRAM Frequency Auto

DRAM Timing Mode Auto Bank Interleaving Auto Channel Interleaving XOR of Address bits

Memory Configuration

Help Item

Options

Auto Limit Manual

Memory CLK : N/A,667MHz

CAS Latency (T cl) : N/A,9CLK RAS/CAS Delay (Trcd) : N/A,9CLK Row Precharge Time (Trp) : N/A,9CLK Min Active RAS (Tras) : N/A,24CLK RAS/RAS Delay (Trrd) : N/A,4CLK Row Cycle (Trc) : N/A,33CLK

: Move F10: Save ESC: Exit

mnlk

F1:General Help

Enter : Select

F9: Optimized Defaults

Using BIOS

+/-/: Value

DRAM Frequency (Auto)

This item enables users to adjust the DRAM frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable.

DRAM Timing Mode (Auto)

This item enables you to specify the DRAM timing mode to be configured automatically or manually.

Bank Interleaving (Auto)

This item is used to set the bank interleaving.

Channel Interleaving (XOR of Address bits)

This item is used to set the channel interleaving.

Memory CLK (533 MHz, N/A)

This item is used to set the memory clock mode.

CAS Latency (Tcl) (8 CLK, N/A)

This item controls the timing delay (inclockcycles) before the DRAM starts a read command after receiving it.

RAS/CAS Delay (Trcd) (8 CLK, N/A)

This is the amount of time a CAS is performed after a RAS. The lower the better, but some DRAM does not support low figures.

Row Precharge Time (Trp) (8 CLK, N/A)

This item specifies the Row precharge to Active or Auto-Refresh of the same bank.

Min Active RAS (Tras) (20 CLK, N/A)

This item determins the time RAS takes to read from and write to a memory cell.

RAS/RAS Delay (Trrd) (4 CLK, N/A)

This item specifies the active-to-active delay of different banks.

Row Cycle (Trc) (27 CLK, N/A)

Use this item to specify the Row Cycle Time. Press <Esc> to return to the M.I.B.II page.

Advanced Clock Calibration (Auto)

This item can enable greater performance tuning margin for the AMD Phenom Black Edition CPUs. The optimal gain can be seen in configurations that use highend CPU cooling solution in combination with elevated CPU core voltage (CPU VID) value. The motherboards that support “advanced Clock Calibration”-feature should enable power delivery capabilities, specifications in order to maximize the performance tuning potential.

Special ACC (Disabled)

Select disable or enable, Special ACC for ACC “Advanced Clock Calibration” function.

W arning:User please notice, when enable “Special ACC” item, it may cause unexpected issue.

Using BIOS

HT Frequency (Auto)

This item enables users to adjust the HT frequency. The default setting is auto and we recommend users leave the setting unchanged. Modify it at will may cause the system to be unstable.

CPU/HT Reference Clock (MHz) (200)

Use this item to set the CPU/HT Reference Clock through clock gen.

Auto Detect DIMM/PCI Clk (Enabled)

When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.

Spread Spectrum (Enabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

CPU Voltage (Disabled)

This item allows users to adjust the CPU voltage.

DIMM Voltage (Disabled)

This item allows users to adjust the DIMM voltage.

Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This function is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results. (Enable for AM2+ / Disable for AM2)

NB Voltage (+50mV)

This item allows users to adjust the Northbridge voltage.

SB Voltage (1.20V)

This item allows users to adjust the Southbridge voltage.

AMD Athlon (tm) II x2 250 Processor

This is display-only field and displays the information of the CPU installed in your computer

NB CLK (2000 MHz)

This item shows the frequency of Northbridge clock.

Current CPU Frequency (3000 MHz)

This item indicates the current CPU frequency. Users can not make any change tothis item. Please noted that the frequency will be varied with different CPU.

Current CPU Voltage (1.3250v)

This item indicates the current CPU voltage.

Current NB Frequency (2000 MHz)

This item indicates the current NB frequency.

DIMM Voltage Default (1.60v)

This item indicates the current NB frequency

Using BIOS

NB Voltage Default (1.15v)

This item indicates the NB voltage default value.

SB V

oltage Default (1.20v)

This item indicates the SB voltage default value.

Press <Esc> to return to the main menu setting page.

Load Default Settings

This option opens a dialog box to ask if you are sure to install optimized defaults or not. You select [OK], and then press <Enter>, the Setup Utility loads all default values; or select [Cancel], and then press <Enter>, the Setup Utility does not load default values.

Supervisor Password

This page helps you install or change a password.

Supervisor Password :Not Installed

Change Supervisor Password Press Enter

mnlk

Supervisor Password

Enter : Select

: Move

F1:General Help

F10: Save ESC: Exit+/-/: Value

F9: Default settings

Help item

Install or Change the password.

Supervisor Password (Not Installed)

This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.

Change Supervisor Password (Press Enter)

You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password.

Press <Esc> to return to the main menu setting page.

Using BIOS

User Password

This page helps you install or change a password.

User Password

User Password : Not Installed

Change User Password Press Enter

Enter : Select

: Move

mnlk

F1:General Help

F9: Default settings

F10: Save ESC: Exit+/-/: Value

Help item

Install or Change the password.

User Password (Not Installed)

This item indicates whether a user password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.

Change User Password (Press Enter)

You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the user password. This item will show if the supervisor password is set.

Press <Esc> to return to the main menu setting page.

Save & Exit Setup

Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, select [OK] to save and exit, or select [Cancel] to return to the main menu.

Exit Without Saving

Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, select [OK] to discard changes and exit, or select [Cancel] to return to the main menu.

If you have made settings that you do not want to save, use the “Exit Without Saving” item and select [OK] to discard any changes you have made.

Using BIOS

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to

allow BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Ad-

vanced BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.)

3 Prepare a bootable device or create a bootable system disk. (Refer to

Windows online help for information on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s

Web site. Copy these files to the bootable device.

5 Turn off your computer and insert the bootable device in your com-

puter. (You might need to run the Setup Utility and change the the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the bootable device first.)

6 At the C:\ or A:\ prompt, type the Flash Utility program name and the file

name of the new BIOS and then press <Enter>. Example: AMINF340.EXE040706.ROM

7 When the installation is complete, remove the bootable device from the

computer and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically.

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

Using BIOS

Chapter 4

Using the Motherboard Software

About the Software D VD-ROM/CD-ROM

The support software DVD-ROM/CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software. Before installing any software, always inspect the folder for files named README.TXT or something similar. These files may contain important information that is not included in this manual.

1. Never try to install all software from folder that is not specified for use with your motherboard.

2. The notice of Intel HD Audio Installation (optional): The Intel High Definition audio functionality unexpectedly quits working in Windows Server 2003 Service Pack 1 or Windows XP Professional x64 Edition. Users need to download and install the update packages from the Microsoft Download Center “before” installing HD audio driver bundled in the driver disk. Please log on to http://support.microsoft.com/ default.aspx?scid=kb;en-us;901105#appliesto for more information.

Auto-installing under W indows XP/Vista/7

The Auto-install DVD-ROM/CD-ROM makes it easy for you to install the drivers and software for your motherboard.

If the Auto-install DVD-ROM/CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.

The support software DVD-ROM/CD-ROM disc loads automatically under Windows XP/Vista/7. When you insert the DVD-ROM/CD-ROM disc in the DVD-ROM/CDROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.

If the opening screen does not appear; double-click the file “setup.exe” in the root directory.

Using the Motherboard Software

Drivers Tab

Setup

Browse CD

Exit

Utilities Tab

Lists the software utilities that are available on the disk.

Information Tab

Displays the path for all software and drivers available on the disk.

Click the Setup button to run the software installation program. Select from the menu which software you want to install.

The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support disk.

Before installing the software from Windows Explorer, look for a file named README.TXT or something similar. This file may contain important information to help you install the software correctly.

Some software is installed in separate folders for different operating systems.

In installing the software, execute a file named SETUP.EXE by doubleclicking the file and then following the instructions on the screen.

The EXIT button closes the Auto Setup window.

Running Setup

Follow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default optionsare recom-

mended.

4. Click Next run the Installation Wizard. An item installation screen appears:

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Using the Motherboard Software

Windows Vista/7 will appear below UAC (User Account Control) message after the system restart. You must select “Allow” to install the next driver.

Continue this process to complete the drivers installation.

Manual Installation

Insert the disk in the DVD-ROM/CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior no tice.

1. Please refer to the support disk for available software.

Please go to ECS website to download AMD Cool “n” Quiet

This concludes chapter 4.

technology.

Using the Motherboard Software

Chapter 5

Hybrid Graphics® Technology Support

Hybrid Graphics® Technology

The Hybrid Graphics® technology provides significant display performance boost to AMD-based systems by inserting the external PCI Express graphics card and enabling both the discrete GPU and the AMD785G graphics core to render

simultaneously in Hybrid CrossFire Follow the steps below to start the Hybrid Graphics

1.Insert a graphics card (which can be used for Hybrid Graphics HD3400 series) into the PCIEX16 slot. Make sure that the card is properly seated on the slot.

mode.

technology.

technology, such as

* For reference only

2. For Hybrid Graphics®, if display by PCI-Express, you must enter the BIOS, set the Surround View in Advanced Chipset Setup to PCI Express. Then press F10 to save the configuration and exit the BIOS. After entering OS, enter Catalyst Control Center to enable Hybrid CrossFire

Hybrid Graphics® Technology Support

SurroundView

provides the power and convenience of multiadapter, multimonitor support for computers that use a PCI-Express based graphics card in conjunction with ATI integrated graphic processors.

And there are two options: Disabled and PCI Express. If SurroundViewTM set to Disabled, and Init Display First set to

OnBoard, SurroundView based on cancel the Enable CrossFire

will be Enabled by Catalyst Control Center

option.

While if display by OnBoard, you must enter the BIOS, set the Init Display First in Advanced Chipset Setup to OnBoard. Then press F10 to save the configuration and exit the BIOS. After entering OS, enter Catalyst Control Center to enable CrossFire

3. Click with your right mouse button on My Computer, then click the option Manage and choose the Device Man ager, finally, click the Display Adapters. The following screen appears. Be sure that the external ATI graphics (ATI Radeon HD 3400 Grapics) and Onboard graphics (Radeon HD 4200) are both displaying in the Display adapters.

Hybrid Graphics® Technology Support

4. Enter Catalyst Control Center, you can see the option of CrossFireTM, click it and select Enable CrossFire

To disable Hybrid Graphics

, then Hybrid Graphics® starts.

, please make sure to cancel Enable CrossFire

in Catalyst Control Center firstly.

Hybrid Graphics® Technology Support

Memo

Hybrid Graphics® Technology Support

Chapter 6

Setting Up AMD SB710 RAID Configuration

Setting Up a bootable RAID Array

This section explains how to configure a bootable AMD RAID array.

Setting Up the BIOS

Start your computer, then press Delete to enter the BIOS setup.

The BIOS CMOS Setup Utility screen appears.

Figure 1.1 BIOS CMOS Setup Utility Main Screen

Use the arrow keys to select Integrated Peripherals (see Figure 1.1), then press Enter.

The Integrated Peripherals screen (or a screen similar to it) appears.

Figure 1.2 Integrated Peripherals Screen

Use the arrow keys to select the SATA Configuration (see Figure 1.2) and globally set SATA Configuration to RAID.

AMD RAID Configuration

Press F10 to save the configuration and exit. The PC reboots.

Enter the RAID BIOS Setup by pressing Ctrl-F when prompted, and proceed to set up the AMD RAID BIOS as described in the next section.

Configuring the AMD RAID BIOS

The AMD RAID BIOS set up lets you choose the RAID type and which hard drives you want to make part of the array.

Entering the RAID BIOS Setup:

Wait until you see the RAID software prompting you to press Ctrl-F.

The RAID prompt appears as part of the system POST and boot process prior to loading of the OS. You have a few seconds to press Ctrl-F before the screen disappears.

Press Ctrl-F.

The Main Menu screen appears (Figure 1.3).

Figure 1.3 Main Menu

AMD RAID Configuration

Select [2], then select LD 1 in the following page.

The Define LD Menu screen appears (Figure 1.4).

Figure 1.4 Define LD Menu

Using the Define a New Array Screen

If necessary, press the tab key to move from field to field until the appropriate field is highlighted.

•

Selecting the RAID Mode

By default, this is set to Mirroring. To change to a different RAID mode, press the spacebar until the mode that you want appears in the RAID Mode box—RAID0/1/10/JBOD.

Note: Not all RAID levels are supported on all platforms.

• Selecting the Stripe Block Size

Stripe block size is given in kilobytes, and affects how data is arranged on the disk. It is recommended to leave this value at the default Optimal, which is 64KB, but the values can be 64 KB and 128 KB. When choose RAID 1, the Stripe block size is unchangable.

AMD RAID Configuration

Assigning the Disks

1. Select the Assignment to Y to designate a free disk to be used as a RAID array disk.

Figure 1.5 illustrates the Define a New Array screen after two disks have been assigned as RAID 0 array disks.

Figure 1.5 FastBuild Utility—Array Disks Assigned

2. Press Ctrl-Y to save the configuration and exit.

The Define LD Menu screen appears (Figure 1.6).

Figure 1.6 Define LD Menu

AMD RAID Configuration

Press ESC to exit.

The Main Menu screen appears (Figure 1.7).

Figure 1.7 Main Menu

Press Y to reboot.

The following screen appears (Figure 1.8).

Figure 1.8

AMD RAID Configuration

Installing the RAID Drivers

Your system may come with a Windows install CD that already includes AMD RAID drivers. If so, then this section is not relevant.

If that is not the case (or you are trying to install a new version of Windows), then you will need an AMD RAID driver F6 install floppy. Check to see if one came with your system. If not, you can create one by downloading the appropriate driver package and following the steps in this section.

Copy all files in "...\RAID\ATI\SB750\Floppy\Win3264" to a floppy disk.

After you complete the RAID BIOS setup, boot from the Windows CD.

The Windows Setup program starts.

Figure 1.9

Press F6 and wait a few moments for the Windows Setup screen to

appear.

Figure 1.10 Windows Setup—Specify Devices

Specify the AMD drivers.

a Insert the floppy that has the RAID driver, press S, then press Enter.

AMD RAID Configuration

The following Windows Setup screen appears:

Figure 1.11 Windows Setup—Selected SCSI Adapter

b Select “ATI AHCI Compatible RAID Controller-x86 platform” and press Enter for 32-bit OS or Select “ATI AHCI Compatible RAID Controller-x64 platform” and press Enter for 64-bit OS.

The following Windows Setup screen appears listing both drivers:.

Figure 1.12 Windows Setup—AMD drives listed

Press Enter to continue with Windows XP Installation. Be sure to leave the floppy disk inserted in the floppy drive until the blue

screen portion of Windows XP installation is completed, then take out the floppy.

Follow the instructions on how to install Windows XP. After Windows XP is completely installed, it is recommended that you

install the ForceWare software in order to access the FastBuild RAID Management tool.

Note:

Each time you add a new hard drive to a RAID array, the RAID driver will have to be installed under Windows once for that hard drive. After that, the driver will not have to be installed.

AMD RAID Configuration

Memo

AMD RAID Configuration

Chapter 7

Setting Up eJIFFY

Introduction

eJIFFY is a fast boot program under Linux. Instead of waiting Windows O.S to start execution, eJIFFY is ready to provide users the instant enjoyment on web browsing, photo review and online chat just within several seconds after boot up.

Note: eJIFFY is ECS optional feature utility corresponding to the DVD activation and BIOS setup. Please check the hard copy user’s guide or product color-box to see

if the model has embodded eJIFFY feature. (eJIFFY icon on color-box )

Version: 4.0

Setting Up eJIFFY

Installation and BIOS Setup

DVD Activation

Finish the DVD utility setup, and then set the BIOS to complete eJIFFY activation.

1. Insert ECS software utility DVD and enter below “Utilities” screen. Click eJIFFY feature item to install.

2. Follow the onscreen instructions to finish eJIFFY setup.

Setting Up eJIFFY

3. After setting up eJIFFY under Windows, you can switch eJIFFY display/keyboard language from English to your local language. The changes will be applied after

rebooting.

Note: The keyboard language selection list offers several more regional keyboard setups to switch with the default English typing. Please refer to the usage FAQ for

more tips.

Setting Up eJIFFY

4. Restart your computer after eJIFFY installation. Press <DEL> or click the BIOS Setup button on the post screen to enter the BIOS setup page after boot up.

5. And then enter the Advanced Setup page to enable the item ECS eJIFFY Func- tion. Press F10 to save the configuration and exit. Restart your computer.

Note:

1. eJIFFY is available in SATA/IDE/AHCI mode. It does not support RAID configuration and the onboard 34-pin floppy drives.

2. Please refer to ECS website for new eJIFFY application updates.

Setting Up eJIFFY

Entering eJIFFY

The post screen appears within several seconds after boot up and it has three buttons on it, Operating system, eJIFFY and BIOS Setup.

Click to enter the normal OS you have installed

such as Windows.

Click to enter eJIFFY OS.

Click to set the BIOS.

If you click eJIFFY, the following screen will appear. And If you make no choice it will enter the normal OS automatically after ten seconds.

Setting Up eJIFFY

Feature Icons

The following illustration shows the main feature icons that eJIFFY provides on the menu.

eWeb: Firefox for web browsing/webmail and watching flash video.

ePix: Photo viewing.

ePal: On-line chat tool to use the most popular IMs in the world. (MSN, ICQ, AIM, etc.)

Shows ePal on-line connection status.

Shut Down/Restart: Ends your session and turns off the computer./Ends your session and restart the computer..

Click once to connect the storage disk to your computer. Click for the second time to remove your storage disk safely. (please refer to the FAQ for more usage information.)

Shows the network connection status.

Language Control Panel

Switch Keyboard Languages

Setting Up eJIFFY

Usage F AQ

Language Control Panel: Besides setting English as the default interface, eJIFFY offers multi-language displays and keyboard settings for languageswitch. Open the language control panel to select a preferable language setting.

Keyboard Language Setup

Step1. Click

to open the language control panel.

Setting Up eJIFFY

Step 2: Click “Keyboard Language” icon to open the keyboard selection

list, which offers several regional keyboard settings besides default English keyboard.

Step 3: Click the selected keyboard language (e.g. French) and press “OK”.

Setting Up eJIFFY

Tips for Language Switch:

Tip 1: Click “Change Keyboard” icon to switch the typing language.

The typing language on text box will switch to the selected one:

Click again to switch to English typing back.

If you use the default English keyboard, eJIFFY still offers other language

Tip 2.

inputs to switch with English.

Click to enable all possible language inputs you want to apply, and click

“Apply”:

Setting Up eJIFFY

Tip 3. How to change display language?

Open the Language Control Panel and click to show the display language

list. Check your desired display language. Your selected display language will be applied after rebooting.

Setting Up eJIFFY

eWeb: Firefox for web browsing/webmail and watching flash video.

Q1: How to download files to hard disk through eWeb?

Click on the file link directly. Then select “Save File” in the pop-up window.

1. Before downloading files, please “mount” the storage devices to make

Note:

sure the device is connected with eJIFFY interface. (Please refer to the usage FAQ to mount devices)

2. eWeb does not support Office Viewer/Reader/Writer format under eJIFFY interface. Please enter the Operating System to open Office files.

3. eWeb supports to open video/audio files online in Flash player format. Due to firefox limitation, the browser does not support files in Real player or Media player formats.

Setting Up eJIFFY

Q2: How to save image file through eWeb?

1. Select the image you want to save and press the right key of your mouse to show the menu, then click the option “ Save Image As” from the menu.

2. Then the “Save Image” window appears. You may rename the image file in the “Name” column and save the file in a folder as the following picture shows.

Rename the image file.

Then select a

Select a root directory.

subdirectory or click “Create Folder” to create a new

folder.

Click here to save the image

file.

Setting Up eJIFFY

ePix: Photo viewing.

Q1: How to find image files saved in hard disk through ePix?

Enter the ePix window, then click the icon “Folder” located in the upper left-hand corner, then follow the path for the files you have saved to view the image files.

Setting Up eJIFFY

Q2: How to use the fit function under slide show?

1. Click “Edit” and select “Preferences” option from the menu.

2. Click “Viewer” and choose “Keep previous zoom” in “After loading an image”. Close the window and you can use the fit function under slide show now.

Note: ePix supports to view image files only. It cannot support Office Viewer or other forms beside image files. Supported image types are: BMP, JPEG, GIF (including GIF animations), PNG, TIFF, ICO and XPM.

Setting Up eJIFFY

Mount/Unmount Disk.

Q1: What does it mean for “Mount Disk”?

“Mount” means to connect the storage devices to eJIFFY interface. After plugging the external device to the computer such as USB drives, a new disk

icon will appear as the following picture shows. Please click the “mount” prompt on the icon. It will change to to show the device is detected successfully.

Q2: What does it mean for “Unmount Disk”?

“Unmount” is to safely remove the storage devices. To unplug the external storage devices such as USB drives, users need to clik the

“Unmount” prompt as the following picture shows, then the icon will change to , you can remove the device now.

Setting Up eJIFFY

Memo

Setting Up eJIFFY

Chapter 8

Trouble Shooting

Start up problems during assembly

After assembling the PC for the first time you may experience some start up problems. Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips.

a) System does not power up and the fans are not running.

1.Disassemble the PC to remove the VGA adaptor card, DDR memory, LAN, USB and other peripherals including keyboard and mouse. Leave only the motherboard, CPU with CPU cooler and power supply connected. Turn on again to see if the CPU and power supply fans are running.

2. Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case. This is to prevent damage from short circuit.

3. Check the CPU FAN connector is connected to the motherboard.

4. For Intel platforms check the pins on the CPU socket for damage or bent. A bent pin may cause failure to boot and sometimes permanent damage from short circuit.

5. Check the 12V power connector is connected to the motherboard.

6. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

b) Power is on, fans are running but there is no display

1. Make sure the monitor is turned on and the monitor cable is properly connected to the PC.

2. Check the VGA adapter card (if applicable) is inserted properly.

3. Listen for beep sounds. If you are using internal PC speaker make sure it is connected. a. continuous 3 short beeps : memory not detected b. 1 long beep and 8 short beeps : VGA not detected

Trouble Shooting

c) The PC suddenly shuts down while booting up.

1. The CPU may experience overheating so it will shutdown to protect itself. Ensure the CPU fan is working properly.

2. From the BIOS setting, try to disable the Smartfan function to let the fan run at default speed. Doing a Load Optimised Default will also disable the Smartfan.

Start up problems after prolong use

After a prolong period of use your PC may experience start up problems again. This may be caused by breakdown of devices connected to the motherboard such as HDD, CPU fan, etc. The following tips may help to revive the PC or identify the cause of failure.

1. Clear the CMOS values using the CLR_CMOS jumper. Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual. When completed, follow up with a Load Optimised Default in the BIOS setup.

2. Check the CPU cooler fan for dust. Long term accumulation of dust will reduce its effectiveness to cool the processor. Clean the cooler or replace a new one if necessary.

3. Check that the 12V power & ATX connectors are fully inserted into the motherboard connectors. Make sure the latches of the cable and connector are locked into place.

4. Remove the hard drive, optical drive or DDR memory to determine which of these component may be at fault.

Maintenance and care tips

Your computer, like any electrical appliance, requires proper care and maintenance. Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can.

1. Keep your computer in a well ventilated area. Leave some space between the PC and the wall for sufficient airflow.

2. Keep your computer in a cool dry place. Avoid dusty areas, direct sunlight and areas of high moisture content.

3. Routinely clean the CPU cooler fan to remove dust and hair.

4. In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity.

5. Add more memory to your computer if possible. This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span.

6. If possible, ensure the power cord has an earth ground pin directly from the wall outlet. This will reduce voltage fluctuation that may damage sensitive devices.

Trouble Shooting

AC power cord is plu ed gg

start. eand r

Turn on PSU switch

or connect to wall socket

MCLR C OS and restart

Yes

oblem rBoard p

and PSU switch is turned on?

Problem with PSU or board?

If board problem -> contact RMA

-> contact RMA

ng.

er modify BIOS se

System fail to start or unstable

Yes

art the PC stRe

is connected

if CPU 12V power

CLR CMOS and check

has display

Check if monitor

Basic Troubleshooting Flowchart

on is pressed

Power Bu

but PC fails to start.

Check if Power Supply

Yes

(PSU) is working

Unit

Check if monitor h sa

Yes

Any Beep sound？

- If 3 short beeps:

DIMM memory not properly

inserted or memory failure

- If 1 long beep and 8 short beeps:

VGA not detected

play dis

Peripheral device issue

Yes

Halt at POST screen？

Yes

R CMOLC S and restart.

If fail, contact RMA

dnee to CLRCMOS.

- HDD problem.

- CMOS setup error,

Memo

Trouble Shooting

ECS A785GM-AD3, A880GM-A3 User manual User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual