ECS 945PL-A (V.1.1) Manual

Preface

Copyright

This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.

Version 1.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer
makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose.
The manufacturer reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Cor­poration.

Other product names used in this manual are the properties of their respective owners and
are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason­able protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this
equipment to ensure compliance with the pertinent RF emission limits governing this
device. Changes or modifications not expressly approved by the system’s manufacturer
could void the user’s authority to operate the equipment.

Preface

ii

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference
that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-causing
Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le
matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Motherboard

Describes features of the motherboard.

Go to

H

page 1

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Describes installation of motherboard
components.

Go to

Provides information on using the BIOS
Setup Utility.

Go to

Describes the motherboard software

Go to

H

H

H

page 7

page 25

page 41

Preface

TT

ABLE OF CONTENTSABLE OF CONTENTS

T

ABLE OF CONTENTS

TT

ABLE OF CONTENTSABLE OF CONTENTS

Preface i

ii

Chapter 1

Introducing the Motherboard 1

Introduction.................................................................................................1

Feature..........................................................................................................2

Motherboard Components........................................................................4

1

Chapter 2

Installing the Motherboard 7

Safety Precautions......................................................................................7

Choosing a Computer Case.......................................................................7

Installing the Motherboard in a Case......................................................7

Checking Jumper Settings.........................................................................8

Setting Jumpers..............................................................................8

Checking Jumper Settings..............................................................9

Jumper Settings..............................................................................9

Connecting Case Components...............................................................10

Front Panel Connector.................................................................12

Installing Hardware...................................................................................13

Installing the Processor...............................................................13

Installing Memory Modules.........................................................15

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17

Installing a Floppy Diskette Drive...............................................18

Installing Add-on Cards..............................................................19

Connecting Optional Devices......................................................21

Connecting I/O Devices..........................................................................23

7 7

7

7 7

Chapter 3

Using BIOS 25

About the Setup Utility............................................................................25

The Standard Configuration........................................................25

Entering the Setup Utility..............................................................25

Updating the BIOS.......................................................................27

Using BIOS................................................................................................27

Standard CMOS Features...........................................................28

Advanced BIOS Features.............................................................30

Advanced Chipset Features.........................................................34

25 25

25

25 25

iv

Power Management Features......................................................35

Hardware Health Features..........................................................37

BIOS Security Features................................................................39

Load Optimal Defaults................................................................40

Load Performance Defaults.........................................................40

Save Changes and Exit................................................................40

Discard Changes and Exit...........................................................40

Chapter 4

41 41

41

41 41

Using the Motherboard Software 41

About the Software CD-ROM................................................................41

Auto-installing under Windows 2000/XP.............................................41

Running Setup..............................................................................42

Manual Installation..................................................................................44

Utility Software Reference.......................................................................44

Multi-Language Translation

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the 945PL-A motherboard. This motherboard is a high perfor­mance, enhanced function motherboard designed to support the LGA775 socket Intel
Pentium 4/Celeron D/Pentium D processors for high-end business or personal desktop
markets.

The motherboard incorporates the 945PL Northbridge (NB) and ICH7 Southbridge (SB)
chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 800/533 MHz using
a scalable FSB Vcc_CPU. The memory controller supports DDR2 memory DIMM frequen­cies of 533/400 MHz. It supports two DDR Sockets with up to maximum memory of 2 GB.
DDR2 Maximum memory bandwidth of 8.5 GB/s in dual-channel interleaved mode assum­ing DDR2 533 MHz. High resolution graphics via two PCI Express slots, intended for
Graphics Interface, are fully compliant to the PCI Express Base Specification revision 1.0a.

The ICH7 Southbridge supports three PCI slots which are PCI 2.3 compliant. In addition,
one PCI Express x1 slot is supported, fully compliant to the PCI Express Base Specifica­tion, Revision 1.0a. It implements an EHCI compliant interface that provides 480Mb/s
bandwidth for eight USB 2.0 ports. One onboard IDE connector supports 2 IDE devices in
Ultra ATA100/66/33 mode. The Southbridge integrates a Serial ATA host controller that is
SATA II compliant, supporting four SATA ports with maximum transfer rate up to 3.0Gb/s
each.

The 945PL-A motherboard is equipped with advanced full set of I/O ports in the rear panel,
including PS/2 mouse and keyboard connectors, COM1, LPT2, four USB ports, one op­tional LAN port,one optional 1394a port and audio jacks for microphone, line-in and line
out.

1

Introducing the Motherboard

2

Feature

Processor

The 945PL-A uses an LGA775 type of Pentium 4/Celeron D/Pentium D that carries
the following features:

• Accommodates Intel Pentium 4/Celeron D/ Pentium D processors

• Supports a system bus (FSB) of 800/533MHz

• Supports “Hyper-Threading” technology CPU

“Hyper-Threading” technology enables the operating system into thinking it’s hooked
up to two processors, allowing two threads to be run in parallel, both on separate
“logical” processors within the same physical processor.

Chipset

The 945PL Northbridge (NB) and ICH7 Southbridge (SB) chipsets are based on an
innovative and scalable architecture with proven reliability and performance.

945PL (NB)

ICH7 (SB) • Enhanced DMA Controller, interrupt controller, and timer

• Supports 32-bit host bus addressing, decoding up to 2 GB
of the processor’s usable memory address space.

• Supports maximum memory bandwidth of 8.5 GB/s in dual
channel interleaved mode.

• 2 GB/s point-to-point Direct Media Interface (DMI) to ICH7
(1 GB/s)each direction.

• Supports one PCI Express x16 for Graphics Interface, fully
compliant to the PCI Express Base Specification revision

1.0a.

• Supports 256-Mb, 512-Mb and 1-Gb DDR2 technologies
for x8 and x16 devices

functions

• Compliant with PCI Express Base Specification, Revision

1.0a

• Compliant with PCI 2.3 specificaiton

• Compliant with Serial ATA II specification

• Integrated USB 2.0 Host Controller supporting up to eight
USB 2.0 ports

• Integrated IDE controller supports Ultra ATA100/66/33

Memory

• DDR2 533/400 DDR SDRAM with Dual-channel DDR2 architecture

• Accommodates two unbuffered DIMMs

• Up to 1 GB per DIMM with maximum memory size up to 2 GB

Onboard LAN (Optional)

The onboard LAN controller provides the following features:

• Supports 100/10 MB/s N-Way Auto-negotiation operation.

• Compliant with PCI v2.2, 32-bit, 33MHz

• Supports Wake-on-LAN and remote wake-up

• Supports Full Duplex Flow Control (IEEE 802.3x)

• Integrated 10/100/1000 transceiver

• Supports PCI V2.3, 32-bit,33MHz

• Supports fully with IEEE 802.3, IEEE 802.3u and IEEE 802.3ab

Introducing the Motherboard

1394a FireWire (Optional)

• Supports provisions of IEEE Std 1394-1995 standard for High Performance
Serial Bus 1.0 and IEEE Std 1394a-2000

• Provides two 1394a fully compliant cable ports at 400/200/100 Mbit/s

Audio (Optional)

• Compliant with AC’97 2.3 specification with 6-channel support

• 16-bit Stereo full-duplex CODEC with 48KHz sampling rate

• Supports double sampling rate (96KHz) of DVD audio playback

• Direct Sound 3DTM compatible

• Compliant with Intel High Definition Audio, supporting 8-channel DACs with
95dB S/N ratio

• Compatibilities: 192/96/48/44.1 KHz with 24/20/16 bits

• Power support: Digital: 3.3V; Analog: 3.3V/5.0V

• All analog jacks are stereo input and output re-tasking for analog plug&play

Expansion Options

The motherboard comes with the following expansion options:

• Two PCI Express x16 slots for Graphic Interface

• One PCI Express x1 slot

• Three 32-bit PCI v2.3 compliant slots

• One 40-pin IDE low profile connector that support two IDE devices

• One floppy disk drive connector

• Four 7-pin SATA connectors

The 945PL-A motherboard supports UltraDMA bus mastering with transfer rates of
100/66/33 MB/s.

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One parallel port

• Four USB ports

• One 1394a port(optional)

• One LAN port (optional)

• Audio jacks for microphone in, line-in and line out

3

BIOS Firmware

This motherboard uses AMI BIOS that enables users to configure many system
features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memroy timing

The firmware can also be used to set parameters for different processor clock speeds.

Some hardware specifications and software items are subject to change
without prior notice.

Introducing the Motherboard

4

Motherboard Components

Introducing the Motherboard

Table of Motherboard Components

LABEL COMPONENT

1 CPU Socket LGA775 socket for Pentium 4 CPUs

2 DIMM1~2 240-pin DDR2 SDRAM slots

3 ATX1 Standard 24-pin ATX power connector

4 IDE1 Primary IDE channel

5 SATA1~4 Serial ATA connectors

6 JP1 Clear CMOS jumper

7 SYSFAN3 System cooling fan connector

8 FDD1 Floppy diskette drive connector

9 PANEL1 Panel connector switches/LED header

10 SPK1 Speaker header

1 1 IR1 Internal infrared header

12 USB1-2 Front Panel USB headers

13 CHS1 Chasis detect header

14 SYSFAN2 System cooling fan connector
15 CD_IN1 CD-in connector

16 AUDIO1 Front panel audio header

17 PCI1~3 32-bit add-on card slots
18 PCIEX3 PCI Express slot for graphics interface(x4 Mode)

19 PCIEX2 PCI Express x1 slot

20 PCIEX1 PCI Express slot for graphics interface(x16 Mode)

21 ATX4P1 Auxiliary power connector for graphic card

22 CPUFAN1 CPU cooling fan connector

23 ATX12V1 Auxiliary 4-pin power connector

5

This concludes Chapter 1. The next chapter explains how to install the motherboard.

Introducing the Motherboard

6

Memo

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from
static electricity

• Discharge static electricity by touching the metal case of a safely grounded
object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with
the specifications for the ATX system case. First, some features on the motherboard are
implemented by cabling connectors on the motherboard to indicators and switches on the
system case. Make sure that your case supports all the features required. Secondly, this
motherboard supports one or two floppy diskette drives and two enhanced IDE drives.
Make sure that your case has sufficient power and space for all drives that you intend to
install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries a ATX form factor of 305 x 210 mm. Choose a case that
accommodates this form factor.

Installing the Motherboard in a Case

7

Refer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holes
in the motherboard. Place the motherboard over the mounting brackets and secure the
motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots
on your motherboard.

Installing the Motherboard

8

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than
one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on
the correct pins.

The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT

SHORT OPEN

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

9

Jumper Settings

Jumper

JP1

Type

3-pin

To avoid the system unstability after clearing CMOS, we recommend
users to enter the main BIOS setting page to “Load Optimal De­faults” and then “Save Changes and Exit”.

Description

CLEAR CMOS

Setting (default)

1-2: CLEAR CMOS

2-3: NORMAL

Before clearing the
CMOS, make sure to
turn off the system.

Installing the Motherboard

JP1

1

10

Connecting Case Components

After you have installed the motherboard into a case, you can begin con­necting the motherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPUFAN1.
2 Connect the system cooling fan connectors to SYSFAN2/3.
3 Connect the connector for graphics interface to ATX4P1.
4 Connect the case switches and indicator LEDs to the PANEL1.
5 Connect the standard power supply connector to ATX1.
6 Connect the auxiliary case power supply connector to ATX12V1.
7 Connect the case speaker cable to SPK1.

Connecting 20/24-pin power cable

Users please note that the 20-pin and 24-pin power cables can both be con­nected to the ATX1 connector. With the 20-pin power cable, just align the 20­pin power cable with the pin 1 of the ATX1 connector. However, using 20-pin
power cable may cause the system to become unbootable or unstable because of
insufficient electricity.

With ATX v1.x power supply, users please
note that when installing 20-pin power cable,
the latche of power cable falls on the left

20-pin power cable

24-pin power cable

side of the ATX1 connector latch, just as the
picture shows.

With ATX v2.x power supply, users please
note that when installing 24-pin power cable,
the latches of power cable and the ATX1
match perfectly.

Installing the Motherboard

CPUFAN1: CPU Cooling FAN Power Connector

Pin Signal Name Function

1 GND System Ground
2 +12V Power +12V
3 Sense Sensor

4 PWM CPU FAN control

Users please note that the fan connector supports the CPU cooling
fan of 1.1A~2.2A (26.4W max.) at +12V.

SYSFAN2 : System Cooling FAN Power Connectors

Pin Signal Name Function

1 GND System Ground
2 +12V Power +12V
3 Sense Sensor

SYSFAN3 : System Cooling FAN Power Connectors

Pin Signal Name Function
Pin Signal Name Function

1 GND System Ground
2 +12V Power +12V
3 NC Not connected

ATX12V1: ATX 12V Power Connector

11

Pin Signal Name

1 Ground

2 Ground
3 +12V

4 +12V

ATX1: ATX 24-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V
3 COM 15 COM

4 +5V 16 PS_ON

5 COM 17 COM

6 +5V 18 COM
7 COM 19 COM
8 PWR OK 20 -5V

9 +5VSB 21 +5V

10 +12V 22 +5V
11 +12V 23 +5V

12 +3.3V 24 COM

Installing the Motherboard

12

ATX4P1: Auxliary Power Connector for Graphics Interface

Pin Signal Name

1 NC

2 GND

3 GND

Make sure to connect a 4-pin ATX power cable
to ATX4P1; otherwise, the system will be un­stable.

4 +12V

SPK1: Internal speaker

Pin Signal Name

1 VCC

2 Key
3 NC

4 Signal

Front Panel Connector

The front panel connector (PANEL1) provides a standard set of switch and LED connec­tors commonly found on ATX or micro-ATX cases. Refer to the table below for informa­tion:

Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED+ 2 FP PWR/SLP *MSG LED+

3 HD_LED_N Hard disk LED-

5 RST_SW_N Reset Switch

7 RST_SW_P Reset Switch

9 RSVD Reserved

* MSG LED (dual color or single color)

4 FP PWR/SLP *MSG LED-

6 PWR_SW_P Power Switch (+)

8 PWR_SW_N Power Switch (-)

10 Key No pin

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data
is being read from or written to the hard drive. For the LED to function properly, an IDE
drive should be connected to the onboard IDE interface. The LED will also show activity
for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power
on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact
switch that is normally open. When the switch is closed, the board resets and runs POST.

Installing the Motherboard

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentary­contact switch that is normally open. The switch should maintain contact for at least 50 ms
to signal the power supply to switch on or off. The time requirement is due to internal de­bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before
the power supply recognizes another on/off signal.

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount
resistors with the clip of the cooling fan. If the clip of the cooling fan
scrapes across the motherboard, you may cause serious damage to the
motherboard or its components.

On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips.
Also, install the cooling fan in a well-lit work area so that you can clearly
see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change these settings by making changes
to jumpers on the motherboard, or changing the settings in the system Setup Utility. We
strongly recommend that you do not over-clock processors or other components to run
faster than their rated speed.

13

Warning: Over-clocking components can adversely affect the reliability
of the system and introduce errors into your system. Over-clocking can
permanently damage the motherboard by generating excess heat in
components that are run beyond the rated limits.

This motherboard has an LGA 775 socket. When choosing a processor, consider the
performance requirements of the system. Performance is based on the processor design, the
clock speed and system bus frequency of the processor, and the quantity of internal cache
memory and external cache memory.

Installing the Motherboard

14

CPU Installation Procedure

The following illustration shows CPU installation components.

A. Unload the cap

· Use thumb & forefinger to hold the
lifting tab of the cap.

· Lift the cap up and remove the cap
completely from the socket.

B. Open the load plate

· Use thumb & forefinger to hold the
hook of the lever, pushing down and pulling
aside unlock it.

· Lift up the lever.

· Use thumb to open the load plate. Be
careful not to touch the contacts.

C. Install the CPU on the socket

· Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.

D. Close the load plate

· Slightly push down the load plate onto the
tongue side, and hook the lever.

· CPU is locked completely.

E. Apply thermal grease on top of the CPU.

F. Fasten the cooling fan supporting base onto
the CPU socket on the motherboard.

G. Make sure the CPU fan is plugged to the
CPU fan connector. Please refer to the CPU
cooling fan user’s manual for more detail
installation procedure.

1. To achieve better airflow rates and heat dissipation, we suggest that you
use a high quality fan with 3800 rpm at least. CPU fan and heatsink
installation procedures may vary with the type of CPU fan/heatsink sup­plied. The form and size of fan/heatsink may also vary.

2. DO NOT remove the CPU cap from the socket before installing a CPU.

Installing the Motherboard

Installing Memory Modules

This motherboard accomodates two memory modules. It can support two 240-pin 1.8V
DDR2 533/400 DDR SDRAM. The total memory capacity is 2 GB.

DDR2 SDRAM memory module table

Memory module Memory Bus

DDR2 400 200MHz

DDR2 533 266MHz

You must install at least one module in any of the two slots. Each module can be installed
with 256 MB to 1 GB of memory; total memory capacity is 2 GB.

Do not remove any memory module from its antistatic packaging until you
are ready to install it on the motherboard. Handle the modules only by
their edges. Do not touch the components or metal parts. Always wear a
grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR2 SDRAM .
2 Push the latches on each side of the DIMM slot down.
3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the notches

in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it seats

correctly. The slot latches are levered upwards and latch on to the edges of
the DIMM.

6 Install any remaining DIMM modules.

15

Installing the Motherboard

16

d

Table A: DDR2 QVL (Qualified Vender List)

The following DDR2 memory modules have been tested and qualifie

for use with this motherboard.

Type Size Vendor Model Name

Micron MT8HTF3264AG-40EB3 CL3 SS

256MB

DDR2 400

512MB

256MB

DDR2 533

512MB

1GB Infenion HYS64T128020HU-3.7-A

Hynix HYMP532U646-E3 AA

Nanya NT256T64UH4A0F-5A CL3

Hynix HYMP564U648-E3 AA

Nanya NT512T64U88A0F-5A CL3

Samsung M378T3253FG0-CCC

Elixir M2U25664TUH4A0F-37B CL4

Infineon HYS64T32000HU-3.7-A
Kingston KVR533D2N4
Samsung M378T3253FG0-CD5 CL4

Elixir M2U51264TU88A0F-37B

Kingston KVR533D2N4

SAMSUNG M378T6553BGO-CD5

Installing the Motherboard

Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CD-ROM
drive.

About IDE Devices

Your motherboard has one IDE channel interface. An IDE ribbon cable supporting two IDE
devices is bundled with the motherboard.

You must orient the cable connector so that the pin1 (color) edge of the
cable correspoinds to the pin 1 of the I/O port connector.

IDE1: IDE Connector

This motherboard supports four high data transfer SATA ports with each runs up to 150
MB/s. To get better system performance, we recommend users connect the CD-ROM to
the IDE channel, and set up the hard dives on the SATA ports.

IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE.
Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that
one device is set to MASTER and the other device is set to SLAVE. The documentation of
your IDE device explains how to do this.

17

About SATA Connectors

Your motherboard features four SATA connectors supporting a total of four drives. SATA ,
or Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE
hard drives which are currently used in most PCs. These connectors are well designed and
will only fit in one orientation. Locate the SATA connectors on the motherboard and follow
the illustration below to install the SATA hard drives.

Installing Serial ATA Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial
ATA protocol. This SATA cable comes with an SATA power cable. You can connect either
end of the SATA cable to the SATA hard drive or the connector on the motherboard.

SATA cable (optional)

SATA power cable (optional)

Installing the Motherboard

18

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard.
2 Attach the other cable end to the SATA hard drive.
3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

This motherboard does not support the “Hot-Plug” function.

Installing a Floppy Diskette Drive

The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive
ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch
drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one
type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.

You must orient the cable connector so that the pin 1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.

FDD1: Floppy Disk Connector

This connector supports the provided floppy drive ribbon cable. After connecting the single
end to the onboard floppy connector, connect the remaining plugs on the other end to the
floppy drives correspondingly.

Installing the Motherboard

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the
system bus. Expansion slots are a means of adding or enhancing the motherboard’s features
and capabilities. With these efficient facilities, you can increase the motherboard’s capabili­ties by adding hardware that performs tasks that are not part of the basic system.

19

PCIEX1
Slot

PCIEX2
Slot

PCIEX3
Slot

PCI 1~3
Slots

The PCI Express slot is used to install an external PCI Express graphics card
that is fully compliant to the PCI Express Base Specification revision 1.0a.

The PCI Express x1 slots is fully compliant to the PCI Express Base Speci­fication revision 1.0a as well.

The PCI Express slot(x4 mode) allows users to install any other PCI Ex­press device. With two graphics cards installed, this motherboard can enable
quad-display.

This motherboard is equipped with three standard PCI slots. PCI stands for
Peripheral Component Interconnect and is a bus standard for expansion
cards, which for the most part, is a supplement of the older ISA bus standard.
The PCI slots on this board are PCI v2.3 compliant.

1. Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.

2. PCIEX2 slot will be disabled when PCIEX3 slot is installed.

Installing the Motherboard

20

Follow these instructions to install add-on cards:

1. Open the chassis and then remove the slot bracket from the case where you will
be installing the expansion cards.

2. Install your graphics card in the proper slot by pressing the card firmly into the
slot.

3. Drive in the screw to secure the slot bracket of the expanson card.

4. Replace your computer’s chassis cover.

5. Power on the computer, if necessary, set up BIOS utility of expansion card from
BIOS.

6. Install related driver to complete the installation.

Installing two graphics cards

Notes: 1. The two PCIE x16 slots run in two modes. With only one PCI Express Graphics card,
install it onto PCIEX1 slot by default. Having two PCI Express Graphics cards at hand, set
them up onto PCIEx1 and PCIEX3 slots simultaneously.

2. The Scalable D.G.E. supports a four-monitor configuration when PCIE x1 slot and PCIE

x3 slot are working simultaneously.

3. Please note that the graphics card driver supports Windows 2000/XP only.

4. Make sure to connect a 4-pin ATX power cable to the ATX4P1; otherwise, the system will

be unstable.

Installing the Motherboard

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

AUDIO1: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and line-out ports
for easier access.

Pin Signal Name Function

1 MIC Front Panel Microphone input signal
2 GND Ground used by Analog Audio Circuits
3 MIC_BIAS Microphone Power

4 5V Filtered+5V used by Analog Audio Circuits

5 Front_Out_R Right Channel Audio signal to Front Panel
6 Rear_OUT_ R Right Channel Audio signal to Rear Panel

7 NC Not Connected

8 Key No Pin
9 Front_Out_L Left Channel Audio signal to Front Panel

10 Rear_OUT_ L Left Channel Audio signal to Rear Panel

Pin Signal Name

21

CD_IN1: CD Audio Input header

Pin Signal Name Function

1 CD in_R CD In right channel
2 GND Ground
3 GND Ground
4 CD in_L CD In left channel

Installing the Motherboard

22

USB1/2: Front Panel USB header

The motherboard has four USB ports installed on the rear edge I/O port array. Additionally,
some computer cases have USB ports at the front of the case. If you have this kind of case,
use auxiliary USB connector to connect the front-mounted ports to the motherboard.

Pin Signal Name Function

1 USBPWR Front Panel USB Power
2 USBPWR Front Panel USB Power
3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal
5 USB_FP_P0+ USB Port 0 Positive Signal
6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground

8 GND Ground
9 Key No pin
10 NC Not connected

IR1: Infrared port

The mainboard supports an Infrared (IR1) data port. Infrared ports allow the wireless
exchange of information between your computer and similarly equipped devices such as
printers, laptops, Personal Digital Assistants (PDAs), and other computers.

Pin Signal Name Function

1 Not Assigned Not assigned

2 Key N o pin

3 +5V IR Power

4 GND Ground

5 IR_TX IrDA serial output

6 IR_RX IrDA serial input

SATA1/2/3/4: Serial ATA connectors

These connectors are used to support the new Serial ATA devices for the highest date
transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates
limitations of the current Parallel ATA interface. But maintains register compatibility and
software compatibility with Parallel ATA.

Pin Signal Name

Pin Signal Name Function

1 Ground 2 TX+

3 TX- 4 Ground
5 RX- 6 RX+

7 Ground - -

Pin Signal Name

CHS1: Chassis Intrusion Detect header

Pin 1-2 Function

Short Case Open

Open Case Close

Installing the Motherboard

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

23

Parallel Port (LPT2) Use LPT2 to connect printers or other parallel communications

Serial Port Use the COM port to connect serial devices such as mice or
(COM1) fax/modems. COM1 is identified by the system as COM1/3.

LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your computer

USB Ports Use the USB ports to connect USB devices.

Audio Ports

This concludes Chapter 2. The next chapter covers the BIOS.

devices.

to the Network.

Use the three audio jacks to connect audio devices. The first jack
is for stereo line-in signal.The second jack is for stero line-out
signal. The third jack is for microphone.

Installing the Motherboard

24

Memo

Installing the Motherboard

Chapter 3

Using BIOS

About the Setup Utility

The computer uses the latest American Megatrends BIOS with support for Windows Plug
and Play. The CMOS chip on the motherboard contains the ROM setup instructions for
configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configura­tion status and provides you with options to set system parameters. The parameters are
stored in battery-backed-up CMOS RAM that saves this information when the power is
turned off. When the system is turned back on, the system is configured with the values you
stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the
Setup Utility, ensure that you understand the Setup Utility options.

25

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend
that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes
to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines.
POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are
completed, the following message appears:

Using BIOS

26

Press DEL/F1 to enter SETUP

Press the delete key or F1 to access the BIOS Setup Utility.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.



Standard BIOS Features



Boot Configuration Features



Advanced BIOS Features



Advanced Chipset Features



Power Mangement Features

Hardware Health Configure





BIOS Security Features

Load Optimal Defaults

Load Best Performance Settings

Save Changes and Exit

Discard Changes and Exit

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Configure Time and Date. Display System Information.......

v02.58 (C)Copyright 1985-2004, American Mega trends, Inc.

Enter : Select

F9: Optimized Settings

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

ESC Exits the current menu



 Scrolls through the items on a menu



+/-/PU/PD Modifies the selected field’s values

F1 Displays a screen that describes all key functions

F8 Loads the Best Performance Defaults

F9 Loads an optimized setting for better performance

F10 Saves configuration changes and exits setup

ESC: Exit

F10: Save

Using BIOS

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s
Web site. New BIOS provides support for new peripherals, improvements in performance,
or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to allow

BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Advanced

BIOS features, disable it. (Firmware Write Protect prevents BIOS from being
overwritten.

3 Create a bootable system disk. (Refer to Windows online help for information

on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s Web

site. Copy these files to the system diskette you created in Step 3.

5 Turn off your computer and insert the system diskette in your computer’s

diskette drive. (You might need to run the Setup Utility and change the boot
priority items on the Advanced BIOS Features Setup page, to force your
computer to boot from the floppy diskette drive first.)

6 At the A:\ prompt, type the Flash Utility program name and the filename of the

new bios and then press <Enter>. Example: AMINF340.EXE 040706.ROM

7 When the installation is complete, remove the floppy diskette from the diskette

drive and restart your computer. If your motherboard has a Flash BIOS jumper,
reset the jumper to protect the newly installed BIOS from being overwritten.
The computer will restart automatically.

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup
Utility displays a list of the options that are available. A highlight indicates which option is
currently selected. Use the cursor arrow keys to move the highlight to other options. When
an option is highlighted, execute the option by pressing <Enter>.

27

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle
values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a



triangle

 .





) lead to submenus that enable you to change the



Using BIOS

28

Standard BIOS Features

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

System Overview

AMIBIOS

Version : 08.00.12
Build Date : 03/23/05
ID : PF500000

Processor

Typ e : Genuine Intel (R) CPU 3.00GHz
Speed : 3000MHz
Count : 1

System Memory

Size : 256MB

System Time [18:14:22]
Saystem Date [Fri 10/07/2005]

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Processor

The item is automatically detected by the system at start up time. The Processor item shows the
processor type and speed installed in your computer. This is display-only field. You cannot make
changes to this field.

System Memory

The item is automatically detected by the system at start up time. The is display-only field. You
cannot make changes to this field.

Time and Date

The Date and Time items show the current date and time on the computer. If
you are running a Windows OS, these items are automatically updated whenever you make changes
to the Windows Date and Time Properties utility.

Press <Esc> to return to the main menu setting page.

Standard BIOS Features

Enter : Select

F9: Optimized Settings

Help Item

Use [ENTER], [TAB]
or [SHIFT-TAB] TO
select a field.

Use [+] or [-] to
configure system Time.

ESC: Exit

F10: Save

Boot Configuration Features

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Boot Settings Configuration

1st Boot Device [1st FLOPPY DRIVE]
2nd Boot Device [HDD:SM-QUANTUM FIR]
3rd Boot Device [CD/DVD:SS-ASUS CD-]
4th Boot Device [Network: B3 D0 Yuko]
Hard Disk Drives [Press Enter]



Removable Drives [Press Enter]



CD/DVD Drives [Press Enter]



Quick Boot [Enabled]
Quiet Boot [Disabled]
Bootup Num-Lock [On]

+/-/: Value

: Move F1: General Help



F8:Best Performance Settings

Boot Configuration Features

Enter : Select

F9: Optimized Settings

F10: Save

Using BIOS

Help Item

Specifies the boot
sequence from the
available devices.

A device enclosed in
parenthesis has been
disabled in the
corresponding type
menu.

ESC: Exit

 Hard Disk (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Hard Disk Drives

Hard Disk Drives

1st Drive [HDD:SM-QUANTUM FIR]

Help Item

Specifies the boot
sequence from the
available devices.

29

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F10: Save

 Removable Drives (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Removable Drives

1st Drive [1st FLOPPY DRIVE]

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Removable Drives

Enter : Select

F9: Optimized Settings

F10: Save

Scroll to this item and press <Enter> to view the following screen:

 CD/DVD Drives (Press Enter)

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

CD/DVD Drives

1st Drive [CD/DVD:SS-ASUS CD-]

CD/DVD Drives

ESC: Exit

Help Item

Specifies the boot
sequence from the
available devices.

ESC: Exit

Help Item

Specifies the boot
sequence from the
available devices.

+/-/: Value

: Move F1: General Help



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

Using BIOS

F10: Save

ESC: Exit

30

Quick Boot (Enabled)

If you enable this item, the system starts up more quickly be elimination some of the power on test
routines.

Quiet Boot(Disabled)

If enabled,BIOS will show a full screen logo at boot; if disabled, BIOS will set the initial display mode
to BIOS and show the diagnostic POST screen at boot.

Boot Up NumLock (On)

This item defines if the keyboard Num Lock key is active when your system is started.

Press <Esc> to return to the main menu setting page.

Advanced BIOS Features

This page sets up more advanced information about your system. Handle this page with
caution. Any changes can affect the operation of your computer.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Advanced Settings



CPU Configuration [Press Enter]



Floppy Configuration [Press Enter]



IDE Configuration [Press Enter]



SuperIO Configuration [Press Enter]



Voltage Adjustment [Press Enter]

Advanced BIOS Features

Help Item

Configure CPU

+/-/: Value

: Move



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F1: General Help

F10: Save

ESC: Exit

 CPU Configuration (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

CPU Configuration

Manufacturer : Intel
Brand String : Genuine Intel(R) CPU 3.00GHz
Frequency : 3.00GHz
FSB Speed : 800MHz

Cache L1 : 16KB
Cache L2 : 1024KB

Hyper Threading Technology [Enabled]
Max CPUID Value limit [Disabled]
CPU TM function [TM1]
CPU Over-clocking Func. [Disabled]
PCIE CLK Synchronize [Disabled]

: Move



F8:Best Performance Settings

+/-/: Value

CPU Configuration

Enter : Select

F9: Optimized Settings

Sets the ratio
between CPU Core
Clock and the FSB
Frequency.
Note: If a invalid
ratio has been
entered to this field.
BIOS will restore it
to previous state.

F1: General Help

F10: Save

Help Item

ESC: Exit

Manufacturer/Brand String/Frequency/FSB Speed

These are display-only fields and display the information of current manufacturer, brand of the CPU,
frequency and Front Side Bus of the CPU installed in your computer.

Using BIOS

Cache L1/L2

These items show the actual CPU interal level 1/2 cache size.

Hyper Threading Technology (Enabled)

This item is only available when the chipset supports Hyper-Threading and you are using a Hyper­Threading CPU.

Max CPUID Value Limit (Disabled)

Use this item to enable or disable the Max CPU ID value limit. When supports Prescott and LGA775
CPUs, enables this item to prevent the system from “rebooting” when trying to install Windows
NT4.0.

CPU TM function (TM1)

This item displays CPU’s temperature and enables you to set a safe temperature for CPU.

CPU Over-clocking Fun,(Disabled)

This itm decides the CPU over-clocking function/frequency installed in your system.If the over­clocking fails, please turn off the system power. And then, hold the insert key(similar to the CLEAR
CMOS function) and turn on the power, the BIOS will recover the safe default.

PCIE CLK Synchronize(Disabled)

This item enables or disables you to select PCIE CLK Synchronize or asynchronous.

Press <Esc> to return to Advanced BIOS Features setting page.



Floppy Configuration (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Floppy Configuration

Floppy A [1.44 MB 3 ½”]

Floppy Configuration

Help Item

Select the type of
floppy drive
connected to the
system.

31

: Move



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F1: General Help+/-/: Value

F10: Save

ESC: Exit

Floppy A( 1.44 MB 3 ½)

Use this item to set up size and capacity of the floppy diskette drive(s) installed in the systems.

Press <Esc> to return to Advanced BIOS Features setting page.

Using BIOS

32



IDE Configuration (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

IDE Configuration

ATA/IDE Configuration [Compatible]
Legacy IDE Channels [SATA Pri, PATA Sec]

Primary IDE Master [Not Detected]



Primary IDE Slave [Not Detected]



Secondary IDE Master [Hard Disk]



Secondary IDE Slave [Not Detected]



Hard Disk Write Protect [Disabled]
IDE Detect Time Out (Sec) [35]
ATA (PI) 80Pin Cable Detect [Host ]

: Move F1: General Help



F8:Best Performance Settings

+/-/: Value

IDE Configuration

Enter : Select

F9: Optimized Settings

Help Item

Options

Disabled
Compatible
Enhanced

ESC: Exit

F10: Save

ATA/IDE Configuration (Compatible)

The ATA/IDE option can be configured as “Disabled”, “Compatible (default)” and “Enhanced” in the
BIOS configuration. Windows* 98SE and Windows* Me operating systems do not support Enhanced
mode IDE/Serial ATA resources for more than four devices. If the ATA/IDE option is set to Enhanced
mode, the operating installation will not be able to recognize the drive, and the installation will fail.
Before installing 98SE or Me, the ATA/IDE configuration must be changed from Enhanced to Legacy
mode.

IDE Chennels (SATA Pri, PATA Sec)

Use this item to set up the primary and secondary sequence of IDE channels and SATA channel. If
set ATA/IDE Configuration to Compatible mode and IDE channels to SATA Pri/PATA Sec, users can
only plug in SATA devices on SATA1 and SATA2; if set ATA/IDE Configuration to Compatible mode and
IDE channels as SATA Sec/PATA Pri, users can only plug in SATA devices on SATA3 and SATA4 or else
SATA devices will not be recognized. If set ATA/IDE Configuration to Enhanced mode, then SATA
devices can be plugged into any SATA connector.

Primary/Secondary IDE Master/Slave(Not detected/Hard Disk/Not Detected)

Your computer has two IDE channels and each channel can be installed with one or two devices
(Master and Slave). In addition, this motherboard supports four SATA channels and each channel
allows one SATA device to be installed. Use these items to configure each device on the IDE channel.

If any IDE device is detected in any one of the above items, press <Enter> to reveal the following
information.

Hard Disk Write Protect (Disabled)

Use this item to enable or disable hard disk write protection.

IDE Detect Time Out (35)

This item allows you to set time out for IDE detection.

ATA (PI) 80Pin Cable Detect (Host )

This item allows you to select the mechanism for detecting 80Pin ATA(PI) Cable.

Press <Esc> to return to Advanced BIOS Features setting page.

Using BIOS



SuperIO Configuration (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

IDE Configuration

OnBoard Floppy Controller [Enabled]
Serial Port1 Address [3F8/IRQ4]
Serial Port2 Address [2F8/IRQ3]
Serial Port2 Mode [NORMAL]
Parallel Port Address [378]
Parallel Port Mode [ECP]
ECP Mode DMA Channel [DMA3]
Parallel Port IRQ [IRQ7]

SuperIO Configuration

Help Item

Allows BIOS to
Enable or Disable
Floppy Controller

33

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F10: Save

ESC: Exit

Onboard Floppy Controller (Enabled)

Use this item to enable or disable the onboard floppy disk drive interface. The bios will automatically
detect the existence of floppy.

Serial Port1/2 Address (3F8/IRQ4/2F8/IRQ3)

Use this item to enable or disable the onboard COM1/2 serial port, and to assign a port address.

Serial Port2 Mode (Normal)

If Serial Port 2 Address is not disabled, it allows you to set the Serial Port 2 Mode.

Parallel Port Address (378)

Use this item to enable or disable the onboard Parallel port, and to assign a port address.

Parallel Port Mode(ECP)

Use this item to select the parallel port mode.

ECP Mode DMA Channel (DMA3)

This item assigns a DMA channel to the parallel port. The options are 0, 1, and 3.

Parallel Port IRQ (IRQ7)

Use this item to assign IRQ to the parallel port.

Press <Esc> to return to Advanced BIOS Features setting page.

Using BIOS

34



Voltage Adjustment

Scroll to this item and press <Enter> to view the following screen:

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

CPU Vcore Voltage [Auto]
DIMM Voltage [NORMAL]
NB Vcore Voltage [NORMAL]

: Move



F8:Best Performance Settings

+/-/: Value

Voltage Adjustment

Enter : Select

F9: Optimized Settings

F1: General Help

F10: Save

Help Item

Options

Auto

1.6000V

1.5875V

1.5750V

1.5625V

1.5500V

1.5375V

1.5250V

1.5125V

1.5000V

1.4875V

1.4750V

1.4625V

1.4500V

1.4375V

ESC: Exit

CPU Vcore Voltage (Auto)

This item allows you to adjust the processor’s core voltage to give it a small boost.

DIMM Voltage (NORMAL)

This item allows you to adjust the memory’s voltage.

NB Vcore Voltage (NORMAL)

This item allows you to adjust the Northbridge’s voltage.

Press <Esc> to return to Advanced BIOS Features setting page.

Advanced Chipset Features

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Advanced Chipset Settings

DRAM Frequency [Auto]
Configure DRAM Timing by SPD [Enabled]

Boots Graphic Adapter Priori [PEG/PCI]
Auto Detect PCI Clk [Enabled]
Spread Spectrum [Enabled]

Onboard Device

Legacy USB Support [Enabled]
Audio Controller [Enabled]
LAN Device [Enabled]
LAN Boot ROM [Enabled]

Advanced BIOS Features

Help Item

Options

Auto
400 MHz
533 MHz
667 MHz

: Move F1: General Help



F8:Best Performance Settings

+/-/: Value

Enter : Select

F9: Optimized Settings

F10: Save

ESC: Exit

DRAM Frequency (Auto)

This item determines frequency of DRAM memory.

Configure DRAM Timing by SPD (Enabled)

When this item is set to enable, the DDR timing is configured using SPD. SPD (Serial Presence
Detect) is located on the memory modules, BIOS reads information coded in SPD during system boot
up.

Using BIOS

Boots Graphic Adapter Priori (PEG/PCI)

This item allows you to choose which graphics controller to use as the primary boot device.

Auto Detect PCI Clk (Enabled)

This item allows you to enable or disable the function of detecting the PCI clock automatically.

Spread Spectrum (Enabled)

If you enable this function, it can significantly reduce the EMI (Electro-Magnetic Interference)
generated by the system.

Legacy USB Support (Enabled)

This item allows you to enable or disable Legacy USB support.

AUDIO Controller (Enabled)

Enables and disables the Audio controller.

LAN Device (Enabled)

Enables and disables the onboard LAN.

LAN Boot ROM (Enabled)

This item enables or disables the function of LAN Boot ROM.

Press <Esc> to return to the main menu setting page.

Power Management Features

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Suspend mode [S3(STR)]
Power Management/APM [Enabled]
Repost Video on S3 Resume [No]
PS/2 Keyboard Wakeup [Disabled]
PS/2 Mouse Wakeup [Disabled]
Suspend Time Out [Disabled]
Power Button Mode [On/Off]
Restore on AC Power Loss [Power off]
Resume On Ring [Disabled]
Resume On PME# [Enabled]
USB Device Wakeup From S3 [Disabled]
Resume On RTC Alarm [Disabled]

Power Management Features

Help Item

Select the ACPI
state used for
System Suspend

35

: Move F1: General Help+/-/: Value



F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F10: Save

ESC: Exit

Suspend mode (S3)(STR)

Use this item to define how your system suspends. In the default, S3 (STR), the suspend mode is
suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the system
memory.If you select S1(POS), the suspend mode is equivalent to a software power down.

Power Management/APM (Enabled)

Use this item to enable or disable a power management scheme. If you enable power management,
you can use the items below to set the power management operation. Only APM is supported.

Repost Video on S3 Resume (No)

If STR mode or Auto mode is selected, this item allows you to enable or disable this function.

PS/2 Keyboard/Mouse Wakeup (Disabled)

These items enable or disable you to allow keyboard or mouse activity to awaken the system from
power saving mode.

Using BIOS

36

Suspend Time Out (Disabled)

This sets the timeout for Suspend mode in minutes. If the time selected passes without any system
activity, the computer will enter power-saving Suspend mode.

Power Button Mode (On/Off)

This item lets you install a software power down controlled by the normal power button on your
system.

Restore on AC Power Loss (Power off)

This item defines how the system will act after AC power loss during system operation. When you
set to Off, it will keep the system in Off state until the power button is pressed.

Resume On Ring (Disabled)

The system can be turned off with a software command. If you enable this item, the system can
automatically resume if there is an incoming call on the Modem. You must use an ATX power supply
in order to use this feature.

Resume On PME# (Enabled)

The system can be turned off with a software command. If you enable this item, the system can
automatically resume if there is an incoming call on the PCI Modem or PCI LAN card. You must use
an ATX power supply in order to use this feature. Use this item to do wake-up action if inserting the
PCI card.

USB Device Wakeup From S3 (Disabled)

This item allows you to enable/disable the USB device Wakeup function from S3 mode.

Resume On RTC Alarm (Disabled)

The system can be turned off with a software command. If you enable this item, the
system can automatically resume at a fixed time based on the system’s RTC
(realtime clock). Use the items below this one to set the date and time of the wake-up
alarm. You must use an ATX power supply in order to use this feature.

Press <Esc> to return to the main menu setting page.

Using BIOS

Hardware Health Features

3

3

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Hardware Healthy Configure

Case Open Warning [Disabled]

Shutdown Temperature [Disabled]

Hardware Health Configure

SMART FAN Control [Enabled]
SMART CPU Temperature [70]
CPU Tolerance Temperature [1°]

StartUp Duty-Cycle [128]

SMART SYS Temperature [45]
SYS Tolerance Temperature [1°]

StartUp Duty-Cycle [30%]

System Temperature :21°/69°F

CPU Temperature :69°C/156°F
CPU Fan Speed : 3308 RPM

Hardware Health Features



2

2



37

Help Item

: Move F1: General Help+/-/: Value



Case Open Warning (Disabled)

F8:Best Performance Settings

Enter : Select

F9: Optimized Settings

F10: Save

ESC: Exit

This item enables or disables the warning if the case is opened up, and the item below indicates the
current ststus of the case.

Shutdown Temperature ( Disabled)

This item enables you to set the maximum temperature the system can reach before powering down.

SMART FAN Control (Enabled)

This item allows you to enable/disable the control of the system fan speed by changing the fan
voltage.

SMART CPU Temperature (70°C)

This item specifies the default CPU temperature. The ranges is from 40°C to 100°C.

CPU Tolerance Temperature (1°C)

This item enables users set the value of the CPU temperature to achieve the start and stop status.
The choices are 1°C, 2°C, 3°C and 4°C.

Example: SMART CPU Temperature 70°C + 1°C = Start up

SMART CPU Temperature 70°C - 1°C = Stop

StartUp Duty-Cycle(128)

This is output for FAN PWM value. When the CPU temperature is lower than Target Temp-tolerance
value, the value will remain as “128” for FAN speed.

SMART SYS Temperature (45°C)

This item specifies the default CPU temperature. The ranges is from 40°C to 100°C.

SYS Tolerance Temperature (1°C)

This item enables users set the value of the CPU temperature to achieve the start and stop status. The choices are 1°C, 2°C,
3°C and 4°C.

Example: SMART CPU Temperature 70°C + 1°C = Start up

SMART CPU Temperature 70°C - 1°C = Stop

StartUp Duty-Cycle(30%)

This item allows users to manually set the StartUp Duty-Cycle of the smart fan, in order to let the
system control the fan speed in an efficient way.

Using BIOS

38

System/CPU Temperature

These items display System/CPU temperatures.

CPU Fan Speed

These items display CPU Fan speed.

System Component Characteristics

These fields provide you with information about the systems current operating status. You cannot
make changes to these fields.

• SYSFan2 Speed

• CPU Vcore

• NB Vcore

• +12V

• +5V

• +5VSB

• VBAT

Using BIOS

BIOS Security Features

This option displays basic information about your system.

CMOS Setup Utility - Copyright (c) 1985-2004, American Megatrends, Inc.

Security Settings

Supervisor Password : Not Installed
User Password : Not Installed

Change Supervisor Password [Press Enter]
Change User Password [Press Enter]

Boot Sector Virus Protection [Disabled]

BIOS Security Features

Help Item

Install or Change
the password.

39

: Move F1: General Help



F8:Best Performance Settings

+/-/: Value

Enter : Select

F9: Optimized Settings

F10: Save

ESC: Exit

Supervisor Password/User Password (Not Installed)

This item indicates whether a supervisor password/user password has been set. If the password has
benn installed, Installed displays. If not, Not Installed displays.

Change Supervisor Password/Change User Password (Press Enter)

You can select this option and press <Enter> to access the sub menu. You can use the sub menu to
change the supervisor password.

Boot Sector Virus Protection (Disabled)

If set to Disabled, when anything attempts to access the boot sector or hard disk partition table, there
will be no warning message to appear.

Press <Esc> to return to the main menu setting page.

Using BIOS

40

Load Optimal Defaults

This option opens a dialog box that lets you install optimized defaults for all appropriate
items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press
<N> and then <Enter> to not install the defaults. The optimized defaults place de­mands on the system that may be greater than the performance level of the components,
such as the CPU and the memory. When your hardware does not support the “Opti­mized Defaults”, fatal system errors or instability may occur. If you only want to install
setup defaults for a specific option, select and display that option, and then press <F7>.

Users please remain the factory BIOS default setting of “Load Optimized Defaults”
when install Operation System onto your system.

Load Performance Defaults

If you select this item and press Enter a dialog box will appear. If you select [OK], and
then Enter, the Setup Utility loads a set of performance default values. These default
settings are quite demanding and your system might not function properly if you are
using slower CPU, memory, or other low-performance components.

Warning: To load Performance settings may make your system become unstable or unbootable.
When loading the Performance Defaults fails, users can choose “either” step to return the
motherboard to its defaults BIOS:

1. Power on the system and press “Insert” key. The system will bypass the previous BIOS
setting and automatically reload the default BIOS. (This procedure is BIOS setup only!)

2. Apply to the jumper setting reference onboard and proceed with the “Clear CMOS” to
recover the default BIOS setting. Please refer to Chapter 2, page 9, to complete the clear
CMOS action. (This procedure requires opening the chasis!)

Save Changes and Exit

Highlight this item and press <Enter> to save the changes that you have made in the Setup
Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <OK>
to save and exit, or press <Cancel> to return to the main menu:

Discard Changes and Exit

Highlight this item and press <Enter> to discard any changes that you have made in the
Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears,
press <OK> to discard changes and exit, or press <Cancel> to return to the main menu.

If you have made settings that you do not want to save, use the “Discard Changes
and Exit” item and press <OK> to discard any changes you have made.

Using BIOS

Chapter 4

Using the Motherboard Software

About the Software CD-ROM

The support software CD-ROM that is included in the motherboard package contains all the
drivers and utility programs needed to properly run the bundled products. Below you can find
a brief description of each software program, and the location for your motherboard
version. More information on some programs is available in a README file, located in the
same directory as the software. Before installing any software, always inspect the folder for
files named README.TXT, INSTALL.TXT, or something similar. These files may con­tain important information that is not included in this manual.

The Intel High Definition audio functionality unexpectedly quits working in Win­dows Server 2003 Service Pack 1 or Windows XP Professional x64 Edition. Users
need to download and install the update packages from the Microsoft Download
Center “before” installing HD audio driver bundled in the driver CD. Please log
on to http://support.microsoft.com/default.aspx?scid=kb;en-us;901105#appliesto
for more information.

Auto-installing under Windows 2000/XP

The Auto-install CD-ROM makes it easy for you to install the drivers and software for your
motherboard.

If the Auto-install CD-ROM does not work on your system, you can still install
drivers through the file manager for your OS (for example, Windows Ex­plorer). Refer to the Utility Folder Installation Notes later in this chapter.

41

The support software CD-ROM disc loads automatically under Windows 2000/XP. When
you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically
bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.

If the opening screen does not appear; double-click the file “setup.exe” in
the root directory.

Using the Motherboard Software

42

Setup Tab

Setup

Browse CD

Exit The EXIT button closes the Auto Setup window.

Application Tab

Lists the software utilities that are available on the CD.

Read Me Tab

Displays the path for all software and drivers available on the CD.

Click the Setup button to run the software installation program. Select
from the menu which software you want to install.

The Browse CD button is the standard Windows command that allows
you to open Windows Explorer and show the contents of the support
CD.

Before installing the software from Windows Explorer, look for a file
named README.TXT, INSTALL.TXT or something similar. This file
may contain important information to help you install the software
correctly.

Some software is installed in separate folders for different operating
systems. Always go to the correct folder for the kind of OS you are using.

In install the software, execute a file named SETUP.EXE or INSTALL.EXE
by double-clicking the file and then following the instructions on the
screen.

Running Setup

Follow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

The following screens are examples only. The screens and driver lists will be
different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

4. Click Next run the Installation Wizard. An item installation screen appears:

43

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instruc­tions, confirm commands and allow the computer to restart a few times to complete the
installation.

Using the Motherboard Software

44

Manual Installation

Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory.
This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path to
begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that auto­matically detects your operating system before installation. Other drivers have the setup
program located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operating
system subfolder and locate the readme text file (README.TXT or README.DOC) for
information on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided
only for the convenience of the customer. The following software is furnished under license
and may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.

AMI/AWARD Flash Utility

This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard,
and lets you copy an updated version of the BIOS to the chip. Proceed with caution when
using this program. If you erase the current BIOS and fail to write a new BIOS, or write a
new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for
more information.

WinFlash Utility

The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility.
The utility enables you to flash the system BIOS stored on a Flash Memory chip on the
motherboard while in a Windows environment. This utility is currently available for
WINXP\2000. To install the WinFlash utility, run WINFLASH.EXE from the following
directory: \UTILITY\WINFLASH 1.51

This concludes Chapter 4.

Using the Motherboard Software

Caractéristiques

Processeur

La 945PL-A utilise un type LGA775 de Pentium 4/Celeron D/Pentium D présentant les
fonctionnalités suivantes:

• Peut recevoir les processeurs Intel Pentium 4/Celeron D/Pentium D

• Support un bus système (FSB) de 800/533 MHz

• Supporte le CPU de technologie “Hyper-Threading”

La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est connecté
à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des processeurs
‘logiques’ dans le même processeur physique.

Chipset

Le chipset 945PL Northbridge (NB) Chipset et ICH7 Southbridge (SB) se base sur une archi
tecture innovante et évolutive avec des performances et une fiabilité éprouvées.

945PL (NB)

• Prend en charge l’adressage de bus hôte 32 bits, permettant
au CPU d’accéder à l’espace de 2 Go complet d’adresse mé
moire.

• Prend en charge une bande passante mémoire maximum de
8,5 Go/s en mode entrelacé double canal.

• Interface Direct Media (DMI) point à point de 2 Go/s vers chaque
direction ICH7 (1 Go/s).

• Prend en charge un PCI Express x16 pour Interface Graphique,
entièrement conforme à la Spécification de Base PCI Express
révision 1.0a.

• Prend en charge les technologies DDR2 256-Mb, 512-Mb et
1-Gb pour x8 et x16 périphériques

Français

-

-

ICH7 (SB)

• Fonctions de Contrôleur DMA Amélioré, de contrôleur d’inter-

ruption, et de minuterie

• Conforme aux spécifications de base PCI Express, Révision

1.0a

• Conforme aux spécifications PCI 2.3.

• Conforme aux spécifications ATA II Série

• Contrôleur d’Hôte USB 2.0 intégré prenant en charge jusqu’à

huit ports USB 2.0

• Contrôleur IDE intégré prenant en charge Ultra ATA100/66/33

Mémoire

• SDRAM DDR 533/400 DDR2 avec architecture DDR2 en double canal

• Reçoit deux DIMM sans tampon

• Jusqu’à 1 Go par DIMM avec une taille de mémoire maximum de 2 Go

LAN sur carte (optionnel)

Le contrôleur LAN interne offre les caractéristiques suivantes:

• Supporte le fonctionnement en Auto-négociation N-Way en 100/10 MB/s

• Prend en charge PCI v2.2, 32 bits, 33-MHz

• Prise en charge de Réveil par LAN et réveil distant

• Prend en charge le Contrôle de Flux Full Duplex (IEEE 802.3x)

• Emetteur-récepteur 10/100/1000 intégré

• Prend en charge PCI v2.3, 32 bits, 33-MHz

• Prise en charge totale avec IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Français

1394a FireWire (Optionnel)

• Prend en charge les provisions du standard IEEE Std 1394-1995 pour
hautes performances

• Offre deux ports câble entièrement conformes 1394a à 400/200/100 Mbit/s
Serial Bus 1.0 et IEEE Std 1394a-2000

Audio (Optionnel)

• Conforme aux spécifications AC’97 2.3 prenant en charge 6 canaux

• CODEC full-duplex 16 bits avec vitesse d’échantillonnage de 48MHz

• Prend en charge la vitesse d’échantillonnage double (96KHz) de la lecture
audio DVD

• Compatible Direct Sound 3D

• Conforme à l’audio haute définition d’Intel, prenant en charge les DAC à
8 canaux avec rapport S/B de 95dB

• Compatibilités: 192/96/48/44.1 KHz avec 24/20/16 bits

• Support d’alimentation : Numérique : 3,3V; Analogique : 3,3V/5,0V

• Toutes les prises analogiques sont des entrées et sorties stéréo avec
réattribution des tâches pour plug & play analogiqueb

TM

Options d’extension

La carte mère comporte les options d’extension suivantes :

• Deux logements PCI Express x16 pour interface graphique

• Un logement PCI Express x1

• Trois emplacements PCI v2.3 32bits

• Un en-têtes demi-hauteur IDE de 40 broches supportant deux canaux IDE

• Une interface lecteur de disquettes

• Q

La 945PL-A carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de
transfert de 100/66/33 Mo/s.

uatre connecteurs SATA à 7 broches

E/S intégrées

La carte mère comporte un ensemble complet de connecteurs et de ports E/S :

• Deux ports PS/2 pour souris et clavier

• Un port série

• Un port parallèle

• Q

uatre ports USB

• Un port 1394a

• Un port LAN (optionnel)

• Prises audio pour microphone, ligne d’entrée et ligne de sortie

(optionnel)

Microprogramme BIOS

La carte mère utilise AMI BIOS qui permet à l’utilisateur de configurer bon nombre de fonc­tions du système, dont :

• Gestion d’alimentation

• Alertes de réveil

• Paramètres de CPU

• Synchronisation de CPU et de mémoire

Le micro-programme peut également être utilisé pour définir les paramètres pour différentes
vitesses d’horloge de processeur.

Certaines spécifications matérielles et certains éléments logiciels sont sus
ceptibles de modification sans préavis.

-

Multi-Language Translation

Features

Prozessor

Der 945PL-A benutzt einen Pentium 4/
folgende Eigenschaften:

• Nimmt Intel Pentium 4/Celeron D/Pentium D Prozessoren auf

• Unterstützt einen Systembus (FSB) mit 800/533 MHz.

• Unterstützt CPU mit “Hyper-Threading”-Technologie.

“Hyper-Threading”-Technologie läßt das Betriebssystem glauben, es sei an zwei Prozessoren
angeschlossen, was zwei parallele Threads auf separaten ‘logischen’ Prozessoren im selben
physischen Prozessor erlaubt.

Celeron D/Pentium D des Typs LGA775 und besitzt

Chipsatz

Die 945PL Northbridge (NB) und ICH7 Southbridge (SB) Chipsätze basieren auf einer
innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung.

945PL (NB)

ICH7 (SB)

• Unterstützung einer 32-Bit Host-Bus-Adressierung, welche
der CPU einen Zugriff zum kompletten Speicherplatz von 2 GB
erlaubt.

• Unterstützt eine maximale Speicherbandbreite von 8,5GB/s
im Dualkanal Interleaved-Modus.

• 2 GB/s Punkt-zu-Punkt Direct Media Interface (DMI) zu ICH7
(1 GB/s) in jede Richtung.

• Unterstützung von PCI Express x16 für die Grafikschnittstelle,
gemäß den PCI Express-Base-Spezifikationen Revision 1.0a.

• Unterstützung von 256-Mb, 512-Mb und 1-Gb DDR2­Technologien für x8 und x16 Zubehör.

• Verbesserter DMA-Kontroller, Unterbrechungskontroller und
Zeitfunktionen.

• Gemäß PCI Express-Base-Spezifikationen, Revision1.0a.

• Gemäß Spezifikationen von PCI 2.3.

• Gemäß Serial ATA II Spezifikationen.

• Integrierter USB 2.0 Host-Kontroller, welcher bis zu acht USB

2.0 Steckvorrichtungen unterstützt.

• Integrierter IDE-Kontroller, welcher Ultra ATA100/66/33
unterstützt.

Deutsche

Arbeitsspeicher

• DDR2 533/400 DDR SDRAM mit Dualkanal DDR2-Architektur

• Es können zwei ungepufferte DIMMs aufgenommen werden.

• Bis zu 1 GB pro DIMM mit maximaler Speicherkapazität von bis zu 2 GB.

Onboard LAN (Optional)

Der Onboard-LAN-Kontroller hat folgende Eigenschaften:

• Unterstützt den Betrieb bei 100/10 MB/s N-Way Auto-Negotiation

• Unterstützung von PCI v2.2, 32-Bit, 33-MHz

• Unterstützung für Wake-on-LAN und Remote Wake-up

• Unterstützt Vollduplex-Flusskontrolle (IEEE 802.3x)

• Enthält 10/100/1000 Transceiver

• Unterstützung von PCI v2.3, 32-Bit, 33-MHz

• Volle Unterstützung mit IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Deutsche

1394a Firewire (optional)

• Unterstützt IEEE Std 1394-1995 Standard für eine höhere Leistung

• Bietet zwei Kabelanschlüsse, die vollständig 1394a kompatibel sind, bei
400/200/100 MBit/s Serial-Bus 1.0 und IEEE Std 1394a-2000

Audio(optional)

• Entspricht AC’97 2.3 Spezifikationen unterstützt 6-Kanal

• 16-Bit Stereo-Vollduplex CODEC mit einer Samplingrate von 48MHz

• Unterstützt bei der DVD-Audiowiedergabe die doppelte Samplingrate
(96KHz)

• Kompatibel mit Direct Sound 3DTM

• Entspricht Intel High Definition Audio, unterstützt 8-Kanal DACs mit 95dB
S/N Ratio

• Kompatibilität: 192/96/48/44.1 KHz mit 24/20/16 Bits

• Stromversorgung: Digital: 3.3V; Analog: 3.3V/5.0V

• Alle analogen Buchsen mit Stereo-Input und Output-Retasking für analoges
Plug & Play

Erweiterungsmöglichkeiten

Das Motherboard ist mit den folgenden Erweiterungsmöglichkeiten ausgestattet:

• Zwei PCI Expressx16-Slots für Grafik-Interface

• Ein PCI Express x1 Slot

• Drei 32-bit PCI v2.3-Steckplätze

• Einen 40-Pin IDE low profile-Stecker, die zwei IDE-Kanäle unterstützen

• Ein Diskettenlaufwerkanschluss

• Vier 7-Pin SATA Anschlüsse

Die 945PL-A-Motherboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate
von 100/66/33 MB/Sek.

Integrierte I/O-Schnittstellen

Das Motherboard verfügt über einen kompletten Satz von I/O-Schnittstellen und
Anschlüssen:

• Zwei PS/2-Anschlüsse für Maus und Tastatur

• Eine serielle Schnittstelle

• Eine parallele Schnittstelle

• Vier USB Schnittstelle

• Ein 1394a-Anschluss (optional)

• Ein LAN-Anschluss (optional)

• Audiobuchsen für Mikrofon, Line-In und Line-Out

BIOS-Firmware

Das Motherboard verwendet AMI BIOS, das es Benutzern gestattet, viele Systemfunktionen
inkl. der Folgenden zu konfigurieren:

• Energieverwaltung

• Aufweckfunktionen

• CPU-Parameter

• CPU- und Arbeitsspeicherfrequenz

Die Firmware kann auch zur Einstellung von Parametern für verschiedene Prozessortaktge
schwindigkeiten verwendet werden.

Manche Hardwarespezifikationen und Softwareelemente können ohne Ankün­digung geändert werden.

-

Multi-Language Translation

Caratteristiche

Processore

Il 945PL-A sfrutta un Pentium 4/Celeron D/Pentium D di tipo LGA775 che dispone delle
seguenti caratteristiche:

• Compatibile con processori Intel Pentium 4/Celeron D/Pentium D

• Supporta un bus di sistema (FSB) fino a 800/533 Mhz

• Supporta CPU con tecnologia “Hyper Threading”

La tecnologia “Hyper-Threading” induce il sistema operativo a pensare di essere collegato
a due processori, questo permette di eseguire due thread in parallelo, ambedue su processori
“logicamente” separati all’interno dello stesso processore.

Chipset

I chipset Intel 945PL Northbridge (NB) e ICH7 Southbridge (SB) sono basati su una architettura
innovativa e scalabile dalle prestazioni e affidabilità garantite.

945PL (NB)

ICH7 (SB)

• Supporta un indirizzamento host bus da 32 bit, consentendo
alla CPU di accedere a tutti i 2 GB della memoria di sistema.

• Supporto di larghezza di banda di memoria massima di 8,5
GB/s in Interleaved Mode a Dual Channel.

• Interfaccia DMI (Direct Media Interface) point-to-point da 2
GB/s in ciascuna direzione (1 GB/s) ICH7.

• Supporta un PCI Express x16 per interfaccia grafica,
completamente compatibile con le specifiche di revisione

1.0a di PCI Express Base.

• Supporta tecnologie DDR2 da 256-Mb, 512-Mb e 1-Gb per
dispositivi x8 e x16

• Controller DMA migliorato, controller interrupt e funzioni di
timer

• Compatibile con le Specifiche di base del PCI Express,
Revision1.0a

• Conforme alle specifiche PCI 2.3.

• Conforme alle specifiche Serial ATA II

• Host Controller USB 2.0 integratoin grado di supporare sino a
8 porte USB 2.0

• Integrato con controller IDE supporta Ultra ATA100/66/33

Memoria

• Supporto di SDRAM DDR 533/400 DDR2 con architettura DDR2 Dual Chan­nel

• Alloggia 2 DIMM unbuffered

• Dimensione massima della DIMM pari ad 1 GB per un ammontare massimo
di 2 GB di memoria

Italiano

LAN integrata (Opzionale)

La funzionalità LAN integrata sulla scheda offre le seguenti caratteristiche:

• Supporto di NWay Auto-negotiation a 100/10 MB/s

• Supporta PCI v2.2, 32-bit, 33-MHz

• Supporto di funzionalità Wake-on-LAN e riattivazione remota

• Supporto di controllo flusso full duplex (IEEE 802.3x)

• Transceiver 10/100/1000 integrato

• Supporta PCI v2.3, 32-bit, 33-MHz

• Completamente conforme con l’IEEE 802.3,IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Italiano

FireWire 1394a (Opzionale)

• Supporto delle disposizioni dello standard IEEE Std 1394-1995 per elevate
prestazioni

• Due porte cable conformi a 1394a con Serial Bus 1.0 a 400/200/100 Mbit/s
e IEEE Std 1394a-2000

Audio(Opzionale)

• Conforme alle specifiche AC’97 2.3 con supporto a 6 canali

• CODEC full-duplex stereo a 16 bit con velocità di campionamento di 48
KHz

• Supporto di velocità di campionamento doppia (96 KHz) per la
riproduzione audio di DVD

• Compatibile con Direct Sound 3D

• Conforme con Intel High Definition Audio e supporto di DAC a 8 canali con
rapporto S/N di 95 dB

• Compatibili: 192/96/48/44.1 KHz a 24/20/16 bit

• Supporto alimentazione: Digitale: 3,3V; Analogico: 3,3 V / 5,0 V

• Tutti i jack analogici offrono ingresso e uscita stereo con riassegnazione
a plug & play analogico

TM

Opzioni di espansione

La scheda madre è dotata delle seguenti opzioni di espansione

• Due slot PCI Express x16 per interfaccia grafica

• Uno slot PCI Express x1

• Tre slot PCI v2.3 a 32 bit

• Una connettori IDE a 40 pin che supportano due canali IDE

• Un’interfaccia per unità disco floppy

• Quattro connettori SATA a 7 pin.

La scheda madre 945PL-A supporta bus master UltraDMA con tasso di trasferimento di
100/66/33 MB/s.

I/O integrati

La scheda madre è dotata di un set completo di connettori e porte I/O:

• Due porte PS/2 per mouse e tastiera

• Una porta seriale

• Una porta parallela

• Quattro porte USB

• Una porta 1394a (opzionale)

• Una porta LAN (opzionale)

• Prese jack audio per microfono, line-in e line-out

Firmware BIOS

Questa scheda madre adotto un BIOS AMI che permette agli utenti di configurare le caratteri­stiche principali del sistema, inclusi:

• Gestione dell’alimentazione

• Allarmi di attivazione

• Parametri CPU

• Sincronizzazione di CPU e memoria

Il firmware può anche essere usato per impostare i parametri per diverse velocità di clock.

Alcune specifiche hardware e software potrebbero essere soggette a
cambiamenti senza preavviso.

Multi-Language Translation

Características

Procesador

La 945PL-A usa un tipo LGA775 de Pentium 4/Celeron D/Pentium D que lleva las sigtes.
características::

• Acomoda procesadores Intel Pentium 4/Celeron D/Pentium D

• Soporta un sistema de bus (FSB) de 800/533 MHz

• Soporta CPU de tecnología “Hyper-Threading”

La tecnología “Hyper-Threading” habilita el sistema operativo para que piense como si
estuviera conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en
procesadores “lógicos” dentro del mismo procesador físico.

Chipset

Los chipsets Northbridge 945PL (NB) y Southbridge ICH7 (SB) están basados en una arquitectura
innovadora y escalable con fiabilidad y rendimiento comprobados.

945PL (NB)

ICH7 (SB)

• Soporta la dirección de bus anfitrión 32-bit, que permite la
CPU acceder a todos los 2 GB del espacio de dirección de
memoria.

• Soporta la ancha de banda de memoria máxima de

8.5GB/s en el modo interlazado de canal dual

• Interfaz Direct Media (DMI) punto a punto de 2 GB/s a
ICH7 (1 GB/s) cada dirección.

• Soporta un PCI Express x16 para la Interfaz de Gráficas,
completamente conforme a la Especificación Base PCI
Express revisión 1.0a.

• Soporta las tecnologías 256-Mb, 512-Mb y 1-Gb DDR2
para los dispositivos x8 y x16.

• Controlador DMA reforzado, controlador de interrupción y
funciones de cornometraje.

• Conforme con la Especificación Base PCI Express,
Revisión1.0a.

• Conforme con la espec. PCI 2.3.

• Conforme con la espec. Serial ATA II

• Controlador Anfitrión USB 2.0 Integrado soporta hasta
ocho puertos USB 2.0.

• Controlador IDE integrado soporta Ultra ATA100/66/33.

Español

Memoria

• DDR SDRAM DDR2 533/400 con arquitectura DDR2 de canal dual

• Acomoda dos DIMMS sin buffer

• Hasta 1 GB por DIMM con el tamaño de memoria máximo hasta 2 GB

LAN en placa (opcional)

El controlador LAN abordo provee las sigtes. características:

• Soporta operación de Autonegociación N-Way de 100/10 MB/s

• Soporta PCI v2.2, 32-bit, 33-MHz

• Soporte de Despertar-en-LAN y Despertar remoto

• Soporta Full Duplex Flow Control (IEEE 802.3x)

• Transceptor 10/100/1000 integrado

• Soporta PCI v2.3, 32-bit, 33-MHz

• Soporte completo con el IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Español

1394a FireWire (Opcional)

• Soporta provisiones de la norma IEEE Std 1394-1995 para el Alto Ren­dimiento

• Provee dos puertos de cable con conformidad total de 1394a en
400/200/100 Mbit/s Bus Serial 1.0 y IEEE Std 1394a-2000

Audio

• Conformidad con las especificaciones AC’97 2.3 que soporta 6 canales

• CODEC de full-duplex estéreo de 16-bit con índice de muestreo de
48MHz

• Soporta doble índice de muestreo (96KHz) de reproducción de audio
DVD

• Compatible con Direct Sound 3DTM

• Conforme con el Audio de Alta Definición de Intel, que soporta DACs de 8
canales con proporción 95dB S/N

• Compatibilidades: 192/96/48/44.1 KHz con 24/20/16 bits

• Soporte de suministro: Digital: 3.3V; Analógico: 3.3V/5.0V

• Todas las clavijas analógicas son de retoma de entrada y salida de estéreo
para el plug & play analógico

Opciones de expansión

La placa base viene con las opciones siguientes de expansión:

• Dos ranuras PCI Express x16 para la Interfaz de Gráficas

• Una ranura PCI Express x1

• Tres ranuras conforme con 32-bit PCI v2.3

• Una cabezal de perfil bajo 40-pin IDE soporta dos canales IDE

• Una interfaz para unidad de disquete

• Cuatro conectores 7-pin SATA

La placa principal 945PL-A soporta el mastering de bus UltraDMA con índices de transferencia
de 100/66/33 MB/s.

I/O integrado

La placa base tiene un conjunto completo de puertos I/O y conectores:

• Dos puertos PS/2 para ratón y de teclado

• Un puerto serie

• Un puerto paralelo

• Cuatro puertos USB

• Un puerto 1394a

• Un puerto LAN (opcional)

• Clavijas de audio para micrófono, entrada y salida de línea

(opcional)

Firmware de BIOS

La placa base utiliza AMI BIOS que permite a los usuarios configurar muchas funciones
de sistema, incluyendo las siguientes:

• Administración de energía

• Alarmas de encendido

• Parámetros CPU

• Temporización de memoria y CPU

El firmware también puede utilizarse para ajustar los parámetros para diversas velocidades del
reloj del procesador.

Algunas especificaciones de hardware y elementos de software están sujetos
a cambios sin previo aviso.

Multi-Language Translation

Características

Processador

O 945PL-A usa um tipo LGA775 de Pentium 4/Celeron D/Pentium D que possui as seguintes
características:

• Acomoda processadores Intel Pentium 4/Celeron D/Pentium D

• Suporta um bus sistema (FSB) de 800/533 MHz

• Suporta CPU de tecnologia “Hyper-Threading”

A tecnologia “Hyper-Threading” permite que o sistema operativo “pense” que está ligado a
dois processadores, permitindo que sejam executados dois threads em paralelo, ambos em
processadores “lógicos” separados dentro do mesmo processador físico.

Chipset

Os chipsets da 945PL Northbridge (NB) e ICH7 Southbridge (SB) são baseados em uma
arquitetura inovativa e escalável com performance e confiabilidade comprovada.

945PL (NB)

ICH7 (SB) • Controlador DMA Melhorado, controlador de interruptor, e

• Suporta um endereçamento no host bus de 32-bit, permitindo
que o CPU aceda completamente aos 2 GB de espaço de
endereçamento da memória.

• Suporta largura de banda de memória máxima de 8.5 GB/
seg. no modo interfoliado de bicanal.

• Interface Media Directo (DMI) ponto-para-ponto com 2
GB/seg. para ICH7 (1 GB/seg. ) cada direcção.

• Suporta um PCI Express x16 Interface de Gráficos, que
cumpre inteiramente com a revisão de Especificação de
Base 1.0a. do PCI Express.

• Suporta 256-Mb, 512-Mb e tecnologias 1-Gb DDR2 para
aparelhos x8 e x16

funções de temporizador

• Cumpre com a Especificação de Base do PCI Express,
Revisão 1.0a

• Em conformidade com a especificação PCI 2.3

• Compatível com Série ATA II

• Controlador Host 2.0 USB integrado suportando até oito
portas USB 2.0

• Controlador IDE integrado suporta Ultra ATA100/66/33

Português

Memória

• DDR2 533/400 DDR SDRAM com arquitectura DDR2 bicanal

• Acomoda duas DIMMs sem buffers

• Até 1 GB por DIMM com tamanho de memória máxima de até 2 GB

Onboard LAN (opcional)

O controlador LAN onboard contém as seguintes características:

• Suporta operação de Auto-negociação N-Way 100/10 MB/s

• Suporta PCI v2.2, 32-bit, 33-MHz

• Suporte Wake-on-LAN e wake-up remoto

• Suporta Controlo de Fluxo Duplo Completo (IEEE 802.3x)

• Transreceptor integrado 10/100/1000

• Suporta PCI v2.3, 32-bit, 33-MHz

• Suporta inteiramente com IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

1394a FireWire (Opcional)

Áudio

Português

Opções de Expansão

A motherboard é fornecida com as seguintes opções de expansão:

A 945PL-A motherboard suporta um domínio bus UltraDMA bus com taxas de Transferência
de 100/66/33 MB/s.

I/O Integrado

A motherboard possui um conjunto completo de portas I/O e conectores:

Firmware do BIOS

A motherboard usa o AMI BIOS que permite aos usuários configurar vários recusos do sistema,
como:

O firmware também pode ser usado para definir os parâmetros de diferentes velocidades de
clock do processador.

• Suporta provisões de IEEE Std 1394-1995 standard para Elevada Perfor­mance

• Fornece duas portas de cabo 1394a totalmente compatíveis com Bus de
Série 1.0 a 400/200/100 Mbit/seg. e IEEE Std 1394a-2000

• Cumpre com as especificações AC’97 2.3 suportando 6 canais

• CODEC duplex total Estéreo de 16 bits com taxa de amostragem de
48MHz

• Suporta taxa de amostragem dupla (96KHz) de reprodução áudio DVD

• Compatível com Direct Sound 3D

• Compatível com Alta Definição Áudio da Intel, suportando DACs com 8
canais com rácio 95dB S/N

• Compatibilidades: 192/96/48/44.1 KHz com 24/20/16 bits

• Suporte de alimentação: Digital: 3.3V; Analógico: 3.3V/5.0V

• Todas as fichas analógicas são entradas estéreo e redistribuição de saídas
para ligar & reproduzir analógico

• Duas ranhuras x16 PCI Express slots para Interface de Gráficos

• One ranhura x1 PCI Express

• Três ranhuras compatíveis com PCI v2.3 de 32 bits

• Uma cabeçalhos de baixo perfil IDE 40 pinos, que suportam dois dispositivos

IDE

• Uma interface para unidade de disquete

• Quatro

• Duas portas PS/2 para o rato e o teclado

• Uma porta de série

• Uma porta paralela

• Quatro portas USB

• Uma porta 1394a (opcional)

• Uma porta LAN (opcional)

• Fichas áudio para microfone, entrada de linha e saída de linha

• Gerenciamento de energia

• Alarmes de reativação

• Parâmetros da CPU

• Sincronização da CPU e memória

conectores SATA de 7 pinos

Alguns itens de software e especificação de hardware estão sujeitos a alterações
sem prévio aviso.

TM

Multi-Language Translation

機能

プロセッサ

945PL-AはLGA775タイプのPentium 4/Celeron D/Pentium Dに対応したもので、
その特徴は次の通り：

• Intel Pentium 4/Celeron D/Pentium D プロセッサが搭載可能

• 800/533MHzのシステムバス(FSB)をサポート

• “ハイパースレッド技術対応のCPUを取り付け可能

ハイパースレッド（HT） 技術というのは、オペレーションシステムに2つのプロセッサが存在すると認
識させることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ、平行利用を可能とす
る技術です。

チップセット

945PL Northbridge (NB)とICH7 Southbridge (SB)チップセットは、実証された信頼
性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。

945PL(NB) • 32ビットホストバスアドレシング機能対応、これでCPUが2

ICH7(SB)

GBのメモリアドレス空間すべてをアクセス可能

• メモリ帯域幅は、デュアルチャネルのインターリーブモードで

最大8.5GB/秒まで可能

• 2 GB/秒 point-to-point Direct Media Interface (DMI)

で ICH7とのデータやり取りを1 GB/秒の転送率で実現

• グラフィックインターフェース用PCI Express x16 スロット

を提供、これでPCI Express Base Specification revision

1.0aに完全対応

• ８倍速または１６倍速のデバイスの256-Mbや512-Mb、1-Gb

のDDR2技術に対応

• 強化型DMAコントローラと、割り込みコントローラ、タイマー

機能を提供

• PCI Express Base Specification 1.0a版に完全対応

• PCI 2.3仕様に準拠しています

• シリアルATA II 仕様に準拠し

• 統合型USB 2.0ホストコントローラで、最大8つまでのUSB

2.0 ポートを対応可能

• 統合型IDEコントローラで、Ultra ATA100/66/33サポート

可能

日本語

メモリ

• DDR2 533/400 DDR SDRAM に対応し、デュアルチャネル DDR2 構成を実

現

• 2つの非バッファーDIMMを搭載

• 各DIMMスロットに1 GBまで装着可能で、合計2GBまでをサポート

オンボードLAN (オプション)

オンボードLANコントローラで次の機能を実現：

• 100/10MB/s N-way自動ネゴシエーション操作をサポート

• PCI v2.2, 32-bit, 33-MHzへの対応

• Wake-on-LANと遠隔 wake-upとの機能をサポート

• 全二重フロー制御(IEEE 802.3x)をサポート

• 10/100/1000 トランシーバーを搭載済み

• PCI v2.3, 32-bit, 33-MHzへの対応

• IEEE 802.3、IEEE 802.3u、IEEE 802.3abへの全面対応

Multi-Language Translation

日本語

1394a FireWire (オプション)

• IEEE Std 1394-1995 standard for High Performance”基準に準拠

• 搭載済みの2つの1394a ポートで、Serial Bus 1.0 とIEEE Std 1394a-

2000とに準拠した 400/200/100 Mbit/秒の転送率が可能

オーディオ(オプション)

• 6チャネルをサポートするAC’97 v2.3仕様に準拠

• 48MHzサンプリングレートの16ビットステレオ全二重CODEC

• DVD音声再生のダブルサンプリングレート(96KHz)に対応

• Direct Sound 3DTM に対応

• Intel High Definition Audio規格に準拠することで、95dB S/N率の8チャ

ネル DACをサポート

• 互換性： 24/20/16 ビットでの192/96/48/44.1 KHz

• 電源サポート：デジタルの場合は 3.3V、アナログの場合は3.3V/5.0V

• すべてのアナログ端子は、ステレオ入出力re-tasking機能によるアナログ

plug & playが可能

拡張オプション

本マザーボードでは、次の拡張機能が利用できます。

• グラフィックインターフェース用のPCI Express x16 スロットが2つ

• PCI Express x1 スロットが1つ

• 32ビットPCI v2.3 互換性スロットが3つ

• 40ピンIDEロープロフィルヘッダー(2つのIDEチャネルをサポート)が1つ

• フロッピーディスク　ドライブ　インターフェイス が1つ

• 7ピンSATAコネクタ が4つ

このマザーボードは、100/66/33 MB/秒の転送速度でのUltra DMAバスマスタリングを
サポートします。

統合I/O

マザーボードには、次のI/Oポートやコネクタを揃えています。

マウスとキーボード用のPS/2ポート が2つ

•

• シリアルポート が1つ

• パラレルポート が1つ

• USBポート が4つ

• 1394aポート が1つ(オプション)

• LANポート が1つ(オプション)

• マイク、ラインイン、ラインアウト用オーディオジャック

BIOSファームウェア

本マザーボードはAMI BIOSを採用し、次の機能を含めた多様なシステム構成を行えま
す。

• 電源管理

• ウェークアップアラーム

• CPUパラメータ

• CPUおよびメモリのタイミング

さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更す
ることもできます。

一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更することが
あります。

Multi-Language Translation

특징

프로세서

945PL-A 는 다음과 같은 특징을 지닌 팬티엄 4/셀러론 D /팬티엄 D 의 GA775 타입을
사용한다:

• 인텔 팬티엄 4/셀러론 D /팬티엄 D 프로세서 사용

• 800/533 MHz시스템 버스(FSB) 지원

• ”Hyper-Threading”기술 CPU 지원

”Hyper-Threading”기술은 운영체제를 두 개의 프로세서에 연결한 것처럼 두개의
트래드를 패러럴로 실행하여 같은 물리적 프로세서 안에서 각기 다른
서를 실행할 수 있게 한다.

논리적 프로세

칩셋

945PL Northbridge (NB) 와 ICH7 Southbridge (SB) 칩셋은혁 신적이고 범위성을 지
닌 아키텍쳐를 바탕으로 인정된 신뢰성과 성능을 지닌다.

945PL (NB)

ICH7 (SB)

• 32 비트 호스트 버스 어드레싱 지원으로, CPU 가 총 2 GB 메

모리 어드레스 공간에 액세스할 수 있다.

• 듀얼 채널 인터리브 모드에서 최대 메모리 대역폭 8.5 GB/s

지원

• ICH7 (1 GB/s).에 각 방향으로 2 GB/s point-to-point Direct

Media Interface (DMI)

• 그래픽 인터페이스를 위해 1 개의 PCI Express x16 지원,

PCI Express Base 1.0a 사양 완전 부합.

• x8 및 x16 장치를 위해 256-Mb, 512-Mb, 1-Gb DDR2 기술

지원.

• 보강 DMA 컨트롤러, 인터럽트 컨트롤러, 및 타이머 기능

• PCI Express Base 1.0a 사양 부합

• PCI 2.3 사양 호환.

• 시리얼 ATA II 사양 호환

• 최대 8 개의 USB 2.0 포트를 지원하는 통합 USB 2.0 호스트

컨트롤러

• 통합 IDE 컨트롤러로 Ultra ATA100/66/33 지원

한국인

메모리

• 듀얼 채널 DDR2 아키텍처를 지닌 DDR2 533/400 DDR SDRAM

• 2 개의 unbuffered DIMM 사용

• DIMM 당 최대 1 GB, 최대 메모리 2 GB

보드 내장 LAN (선택 사항)

보드 내장 LAN 컨트롤러는 다음과 같은 특징을 제공한다:

• 100/10 MB/s N-Way Auto-negotiation 작업 지원

• PCI v2.2, 32-bit, 33-MHz 지원

• Wake-on-LAN 및 원격 wake-up 지원

• Full Duplex Flow Control (IEEE 802.3x) 지원

• 통합 10/100/1000 트랜시버

• PCI v2.3, 32-bit, 33-MHz 지원

• IEEE 802.3, IEEE 802.3u, IEEE 802.3ab 전적으로 지원

Multi-Language Translation

한국인

1394a 파이어 와이어 (옵션)

• 고성능용 IEEE Std 1394-1995 표준 지원

• 2 개의 1394a 호환 케이블 포트 제공, 400/200/100 Mbit/s 시리얼 버스 1.0

및 IEEE Std 1394a-2000

오디오(옵션)

• AC'97 2.3 사양 호환, 6 채널 지원.

• 48MHz 샘플링 속도를 지닌 16 비트 스테레오 풀-듀플렉스 코덱

• DVD 오디오 재생 시 더블 샘플링 속도 (96KHz) 지원.

• Direct Sound 3DTM 호환

• 95dB S/N 비율로 8 채널 DAC를 지원하는 HD 오디오 부합

• 호환성: 24/20/16 비트의 192/96/48/44.1 KHz

• 전원 지원: 디지털: 3.3V; 아날로그: 3.3V/5.0V

• 모든 아날로그 잭은 스테레오 입력 및 출력, 아날로그 플러그 앤 플레이를

위한 re-tasking.

확장 옵션

이 메인보드는 다음과 같은 확장 옵션이 있다

• 그래픽 인터페이스 용 PCI Express x 16 슬롯 2 개

• PCI Express x 1 슬롯 1 개

• 32 비트 PCI v2.3 호환 슬롯 3 개

• 2 개의 IDE 채널을 지원하는 40핀 IDE 로우 프로파일 해더 1 개

• 플로피 디스크 드라이브 인터페이스 1 개

• 7 핀 SATA 커넥터 4개

945PL-A 마더보드는 전송 속도 100/66/33 MB/s의 UltraDMA 버스 마스터링을 지원
한다.

통합 I/O

이 메인보드에는 풀 세트의 I/O 포트와 커넥터가 있다

• 마우스와 키보드용 PS/2 포트 2 개

• 시리얼 포트1개

• 패러럴 포트 1 개

• USB 포트 4 개

• 1394a 포트 1 개 (선택 사항)

• LAN 포트 1 개 (선택 사항)

• 마이크, 라인 입력 및 라인 출력용 오디오 잭

BIOS 펌웨어

본 메인보드는 AMI BIOS 를 사용하여 사용자는 다음과 같은 시스템 기능을 구성할
수 있다

• 전원 관리

• Wake-up 알람

• CPU 파라미터

• CPU 및 메모리 타이밍

펌웨어는 다른 프로세서의 클럭 속도를 설정하는 데도 사용될 수 있다

하드웨어 사양 및 소프트웨어 아이템은 사전 통보없이 변경될 수 있
습니다

Multi-Language Translation

功能

處理器

945PL-A 採用LGA775型的Pentium 4/Celeron D/Pentium D，具有如下特徵：

• 可搭配Intel Pentium 4/Celeron D/Pentium D 處理器

• 支援高達 800/533MHz之系統匯流排(FSB)

• 支援使用超執行緒(Hyper-Threading)技術之CPU

利用“超執行緒(HT)”技術，可使作業系統在相當於裝上了兩具處理器的狀態下運
作：利用一個”實體”處理器模擬出兩個獨立的”邏輯”處理器，同時執行兩個工作
緒。

晶片組

945PL北橋(NB)及ICH7南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構，具
備優良的可靠性及性能。

945PL (NB)

• 支援32位元主事匯流排定址，藉此CPU 存取整個2 GB的記憶
位址空間

• 支援的記憶體頻寬在雙通道交錯模式下高達8.5GB/秒

• 提供對ICH7的2 GB/秒點對點Direct Media Interface
(DMI)，雙向1 GB/秒

• 具有一個繪圖卡用之PCI Express x16 介面，完全符合PCI
Express Base Specification 1.0a版

• 支援8倍速及16倍速之256-Mb、512-Mb、及1-Gb DDR2技術

ICH7 (SB)

• 增強型DMA控制器、中斷控制器、及計時功能

• 符合PCI Express Base Specification 1.0a版

• 符合PCI 2.3規格

• 符合序列ATA II 規格

• 內建式USB 2.0主控，可支援8個USB 2.0埠

• 整合式IDE控制器，支援Ultra ATA100/66/33

記憶體

• 支援DDR2 533/400 DDR SDRAM，提供雙通道DDR2 架構

• 可安裝2個非緩衝式DIMM

• 各DIMM可安裝1GB記憶體，共可支援高達2 GB的記憶體容量

內建區域網路 (選購)

機載區域網路控制器具有如下功能：

• 支援 100/10MB/s N-way 自動協調作業

• 支援PCI v2.2, 32位元, 33MHz

• 支援區域網路喚醒功能及遠距喚醒功能

• 支援全雙工流量控制(IEEE 802.3x)

• 整合有10/100/1000 收發器

• 支援PCI v2.3, 32位元, 33MHz

• 支援IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

繁體中文

繁體中文

1394a FireWire (選項)

• 支援「IEEE Std 1394-1995 standard for High Performance」 規格

• 提供2個1394a 相容埠，提供400/200/100 Mbit/秒之傳輸速度，並符合Se­rial Bus 1.0 及 IEEE Std 1394a-2000

音效(選項)

• 相容於AC'97 2.3 規格並且支援6聲道

• 16位元立體聲全雙工CODEC，取樣率48MHz

• 支援DVD音訊播放的雙取樣率(96KHz)

• Direct Sound 3DTM 相容

• 相容於Intel High Definition Audio規格，可支援95dB S/N 比的 8聲道
DAC

• 相容性：24/20/16位元下之192/96/48/44.1 KHz

• 電源支援：3.3V(數位時)，3.3V/5.0V(類比時)

• 所有類比插頭均具類比隨插即用的立體環場音訊輸入及輸出的重組態(re­tasking)功能

擴充選項

本主機板包括下列擴充選項：

• 2個繪圖介面用之PCI Express x16 插槽

• 1個PCI Express x1 插槽

• 3個32位元PCIv2.3插槽

• 1個40針IDE接頭(支援2個IDE裝置)

• 1個軟碟機介面

• 4個7針SATA插頭

本主機板支援傳輸率100/66/33 MB/秒下的Ultra DMA 匯流排主控功能。

整合 I/O

主機板具有一組齊全的 I/O 連接埠及連接頭：

• 2 個 PS/2 埠，供滑鼠與鍵盤使用

• 1 個串列埠

• 1 個平行埠

• 4 個USB埠

• 1 個1394a埠

• 1 個區域網路埠(選購)

• 麥克風音頻插座、線級輸入及線級輸出

(選購)

BIOS 韌體

本主機板使用AMI BIOS，使用者可以組態設定許多系統功能，包括如下：

• 電源管理；

• 喚醒警鈴；

• CPU參數；

• CPU及記憶體的時脈定時。

此外，也可藉由參數的設定，調整處理器的時脈速度。

部份硬體規格和軟體內容可能會在未經通知的情況下更動，敬請見諒。

Multi-Language Translation

功能

处理器

945PL-A 使用 LGA775 型 Pentium 4//Celeron D/Pentium D CPU，具备以下特点：

• 支持 Intel Pentium 4/Celeron D/Pentium D 处理器

• 支持 800/533 MHz 系统总线 (FSB)

• 支持“多线程”技术 CPU

“多线程”技术可以让操作系统认为自己连接了两个处理器，允许两个线程并行运行，
每个线程位于同一处理器中的单独“逻辑”处理器中。

芯片组

945PL北桥 (NB) 和 ICH7 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构，能提
供已经证明的可靠性和高性能。

945PL (NB)

• 支持 32 位主机总线寻址，允许 CPU 访问 2 GB 的完整内

存地址空间

• 在双通道隔行模式下支持 8.5 GB/s 最大存储带宽

• 每个方向 2 GB/s 点到点直接媒体接口 (DMI) 到 ICH7 (1

GB/s)

• 支持 1 个 PCI Express x16 用于图形接口，完全符合 PCI

Express Base 规格 1.0a

• 支持用于 x8 和 x16 设备的 256-Mb、512-Mb 和 1-Gb

DDR2 技术

ICH7 (SB)

• 增强 DMA 控制器、中断控制器和定时器功能

• 符合 PCI Express Base 规格 1.0a

• 符合 PCI 2.3 规格

• 符合串行 ATA II 规格

• 集成 USB 2.0 主控器，最多支持 8 个 USB 2.0 端口

• 集成 IDE 控制器，支持 Ultra ATA100/66/33

内存

• DDR2 533/400 DDR SDRAM，双通道 DDR2 架构

• 支持 2 个非缓冲 DIMM

• 每个插槽支持 1 GB，总共最大可支持 2 GB

Onboard LAN (可选)

板上集成的 LAN 控制器提供以下功能：

• 支持 100/10 MB/s N 路自协商工作

• 支持 PCI v2.2，32-位，33-MHz

• 支持 LAN 和远程唤醒

• 支持全双工流控制 (IEEE 802.3x)

• 集成 10/100/1000 收发器

• 支持 PCI v2.3，32-位，33-MHz

• 完全支持 IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

简体中文

简体中文

1394a 火线（可选）

• 支持之前的高性能 IEEE Std 1394-1995 标准

• 提供两个2 个电缆端口，支持 400/200/100 Mbit/s 串行总线 1.0 和 IEEE

Std 1394a-2000

音频

• 兼容 AC’97 v2.3 规格并支持 6 通道

• 具有 48MHz 采样速率的 16 位全双工 CODEC（编解码器）

• 支持 DVD 音频播放的双采样速率 (96KHz)

• 符合 Direct Sound 3DTM 规格

• 符合高精度音频规格，支持 8 通道 DAC，95dB 信噪比

• 兼容性：192/96/48/44.1 KHz，24/20/16 位

• 电源支持：数字：3.3V；模拟：3.3V/5.0V

• 所有模拟插孔为立体声输入和输出并重新指定为模拟即插即用

扩展选项

此主板提供如下扩展选项：

• 2 个用于图形接口的 PCI Express x16 插槽

• 1 个 PCI Express x1 插槽

• 3 个 32 位 PCI 扩展插槽

• 1 个 40-pin IDE 紧凑型接口，支持 2 个 IDE 通道

• 1 个软驱接口

• 4 个 7-pin SATA 接口

主板945PL-A支持 Ultra DMA 总线控制，传输速率可达 100/66/33 MB/sec。

集成 I/O

此主板具有完整的 I/O 端口和插孔：

• 2 个用于连接鼠标和键盘的 PS/2 端口

• 1 个串口

• 1 个并口

• 4 个 USB 端口

• 1 个 1394a 端口（可选）

• 1 个 LAN 端口（可选）

• 麦克风、线入和线出声音插孔

BIOS

此主板使用 AMI BIOS，可以让用户自己配置以下系统功能：

• 电源管理

• 唤醒报警

• CPU 参数

• CPU 和记忆定时

还可用于设置不同处理器时钟速度的参数。

某些硬件规格和软件项目若有更改恕不另行通知。

Multi-Language Translation

Характеристики

Процессор

Плата 945PL-A построена на базе процессора Pentium 4/Celeron D/Pentium D LGA775 и
обладает следующими характеристиками:

• Размещает процессоры Intel Pentium 4/Celeron D/Pentium D

• Поддерживает системные шины (FSB) с частотой 800/533MHz

• Поддерживает технологию CPU “Hyper-Threading”

Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине
имеется два процессора; это позволяет параллельно обслуживать два процесса, причем
каждый из процессов обслуживается отдельным «логическим» процессором в пределах
одного физического процессора.

Чипсет

Чипсеты 945PL «Северный мост» (Northbridge, NB) и ICH7 «Южный мост»
(Southbridge, SB) построены с использованием инновационной масштабируемой
архитектуры, обеспечивающей высокую надежность и производительность.

945PL (NB)

ICH7 (SB)

• Поддерживает 32-битную адресацию хоста, обеспечивая для

CPU адресацию памяти объемом 2ГБ .

• Поддерживает максимальную скорость переноса данных в

память 8.5 ГБ/с в двухканальном режиме чередования

• Интерфейс передачи данных Direct Media point-to-point со

скоростью 2 ГБ/с (DMI) к ICH7 (1 ГБ/с) в каждом направлении.

• Имеет один разъем для подключения карты графики PCI

Express x16; обеспечивает полную соместимость с PCI Express
Base, rev. 1.0a.

• Поддерживает технологии 256-Мб, 512-Мб и 1-Гб DDR2 для

устройств

• Расширенные функции контроллера DMA, контроллера
прерываний

• Совместимость с PCI Express Base, Rev. 1.0a

• Совместимость с PCI 2.3

• Совместимость с Serial ATA II

• Встроенный контроллер хоста USB 2.0 с поддержкой до

восьми портов

• Встроенный контроллер IDE с поддержкой Ultra ATA100/66/33

x8 и x16

, внутреннего таймера

USB 2.0

Память

• DDR2 533/400 DDR SDRAM с двухканальной архитектурой DDR2

• Обслуживает 2 модуля небуферизованной памяти DIMM

• Обслуживает до 1 ГБ на модуль DIMM (максимально до 2 ГБ памяти)

Встроенный сетевой адаптер LAN (опционально)

Встроенный сетевой адаптер LAN обладает следующими характеристиками:

• Поддерживает автоматическое определение скорости и режима
соединения 100/10 MB/s

• Поддеркжа PCI v2.2, 32-бит, 33-MГц

• Функция Wake-on-LAN и удаленного пробуждения

• Поддерживает режим управления потоком Full Duplex Flow Control

(IEEE 802.3x)

• Интегрированный трансивер 10/100/1000

• Поддеркжа PCI v2.3, 32-бит, 33-MГц

• Полная совместимость с технологией IEEE 802.3, IEEE 802.3u, IEEE

802.3ab

Multi-Language Translation

Русский

Русский

1394a FireWire (Опционально)

• Поддержка стандарта IEEE Std 1394-1995 для высокоэффективных
технлогий

• Два кабельных порта 1394a, полностью совместимых с
последовательной магистральной шиной 400/200/100 Mбит/с вер. 1.0
стандартом IEEE Std 1394a-2000

Аудио (Опционально)

• Совместимость со спецификацией AC’97 2.3 поддержка 6-канальных

• 16-битный стерео CODEC (полный дуплекс) с частотой сэмплирования
48 МГц

• Поддержка двойной скорости сэмплирования аудиовыхода DVD (96
кГц)

• Совместимость с Direct Sound 3D

• Совместимость с аудио-технологией Intel High Definition, поддержка
8-канального DAC с соотношением сигнал/шум 95дБ

• Совместимость с 192/96/48/44.1 KГц для 24/20/16 бит

• Электропитание: цифровое: 3.3V; аналоговое: 3.3V/5.0V

• Все аналоговые гнезда аудио имеют стереовход и выходa и
пригодны для аналогового plug & play

TM

Возможности расширения

Существуют следуюшие опции расширения данной материнской платы:

• Два слота PCI Express x16 для графического интерфейса

• Один слот PCI Express x1

• Три 32-битных слота PCI v2.3

• Один низкопрофильный 40-штырьковый слот IDE, обеспечивающий
поддержку двух устройств IDE

• Один разъем для накопителя на гибких дисках

• Четыре 7-штырьковых разъема SATA

Плата 945PL-A поддерживает технологию захвата управления шиной UltraDMA bus
mastering со скоростью передачи данных 100/66/33 МБ/сек.

Интегрированный вход/выход

Плата снабжена полным набором портов входа/выхода и разъемов:

• Два порта PS/2 для подключения мыши и клавиатуры

• Один серийный порт

• Один параллельный порт

• Четыре порта USB

• Один порт 1394a (опционально)

• Один порт LAN (опционально)

• Гнездо для подключения микрофона, гнезда аудио-входа и выхода

BIOS

Плата работает под AMI BIOS, который позволяет пользователю конфигурировать
различные характеристики системы:

• Управление питанием

• Сигналы пробуждения системы

• Параметры CPU

• Время доступа для CPU и памяти

BIOS допускает также установку параметров для различных частот процессора.

Некоторые параметры платы и характеристики ее программного
обеспечения могут быть изменены без предварительного уведомления.

Multi-Language Translation

Cechy

Procesor

Płyta główna 945PL-A zaopatrzona jest w procesor Pentium 4/Celeron D/Pentium D typu
LGA775 i charakteryzuje się następującymi cechami:

• Obsługuje procesory Pentium 4/Celeron D/Pentium D firmy Intel

• Obsługuje szynę systemowa (FSB) 800/533MHz

• Zabezpiecza technologię CPU “Hyper-Threading”

Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i
wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden
z dwuch "logicznych" procesorów w ramach jednego fizycznego procesora

Chipset

Mostek północny (NB) 945PL i mostek południowy (SB) ICH7 chipsetu oparty jest na
nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.

945PL (NB)

ICH7 (SB) • Rozszerzony kontroler DMA, kontroler przerywań i funkcje

• Obsługuje 32-bitowe adresowanie hosta pozwalając
procesorowi zaadresować 2 GB pamięci

• Obsługuje transfer zapisanych danych z prędkością do

8.5 GB/s w dwukanałowym trybie pamięci z przeplotem

• Interfejs bezpośredniego połączenia (DMI) typu point-to­point 2 GB/s do ICH7 (1 GB/s) w każdym kierunku

• Obsługuje jedno złącze grafiki PCI Express x16;
całkowicie zgodne z technologią PCI Express Base, w
wersji 1.0a.

• Obsługuje pamięci 256-Mb, 512-Mb i 1-Gb w technologii
DDR2 w urządzeniach x8 i x16

zegara

• Zgodny z technologią PCI Express Base, Rev. 1.0a

• Zgodny z PCI w wersji 2.3

• Zgodny ze standardem Serial ATA II

• Wbudowany kontroler hosta USB 2.0 obsługuje do ośmiu

portów USB

• Wbudowany kontroler IDE obsługujący Ultra

ATA100/66/33

Pamięć

• DDR2 533/400 DDR SDRAM z architekturą dwukanałową DDR2

• Zaopatrzony w dwa gniazda niebuforowanej pamięci typu DIMM

• Obsługuje pamięć DIMM do pojemności 1 GB każda; maksymalna
możliwa pojemność pamięci do 2 GB

Zintegrowana obsługa sieci LAN (opcjonalnie)

Zintegrowana obsługa sieci LAN posiada następujące właściwości:

• Obsluguje N-drożne automatycznie ustalane operacje z szybkościami 100/
10 MB/s

• Obsluguje 32 bitowe PCI w wersji 2.2 o częstotliwościach 33-MHz

• Obsługuje Wake-on-LAN i zdalne wake-up

• Obsługuje Full Duplex Flow Control (zgodnie ze standardem IEEE

802.3x)

• Zintegrowany terminal nadawczo-odbiórczy 10/100/1000

• Obsluguje 32 bitowe PCI w wersji 2.3 o częstotliwościach 33-MHz

• Obsługuje wpełni standard IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Polski

Polski

1394a FireWire (Opcjonalnie)

• Obsługuje standard IEEE Std 1394-1995 dla wysokosprawnych technologii

• Posiada dwa porty 1394a całkowicie kompatybilne z szyną 400/200/100
Mbit/s Serial Bus 1.0 i standardem IEEE Std 1394a-2000

Audio (Opcjonalnie)

• Zgodne ze specyfikacją AC’97 w wersji 2.3 obsługuje 6 kanałów

• 16 bitowe full-duplex CODEC z częstotliwością próbkowania 48MHz.

• DVD audio playback obsługuje z podwójną częstotliwością próbkowania
(96KHz)

• Zgodny z Direct Sound 3DTM

• Zgodny z protokołem Intel High Definition Audio, obsługuje 8 kanałowe
DAC ze stosunkiem sygnał/szum równym 95dB

• Zgodność: 192/96/48/44.1 KHz z 24/20/16 bitami

• Zapewnia zasilanie: 3,3 V cyfrowe; 3.3 V/5.0 V analogowe

• Wszystkie analogowe gniazda wejściowe i wyjściowe typu jack są
stereofoniczne i przystosowane do analogowego plug & play

Możliwości rozbudowy

Płyta głwna wyposażona jest w następujące gniazda:

• Dwa gniazda PCI Express x16 dla kart graficznych

• Jedno gniazdo PCI Express x1

• Trzy 32-bitowych gniazda zgodnych z PCI w wersji 2.3

• Jedno 40-nóżkowe złącze niskoprofilowe obsługujące dwa urządzenia IDE

• Jedno złącze obsługujące stacje dyskietek

• Cztery 7-nóżkowe złącza SATA

Płyta główna 945PL-A obsługuje szynę UltraDMA z szybkością transferu 100/66/33 MB/s.

Zintegrowane We/Wy

Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:

• Dwa gniazda PS/2 dla myszy i klawiatury

• Jedno gniazdo szeregowe

• Jedno gniazdo równoległe

• Cztery gniazda USB

• Jedno gniazdo 1394a (opcjonalnie)

• Jedno gniazdo LAN (opcjonalnie)

• Gniazdo wejściowe mikrofonowe, gniazdo wejściowe i wyjściowe dzwięku
(audio)

Firmowy BIOS

Płyta głwna wyposażona jest w BIOS firmy AMI, który pozwala użytkownikowi
konfigurować wiele cech systemu włączając w to następujące właściwości:

• Zarządzanie poborem mocy

• Alarmy typu Wake-up

• Parametry pracy procesora

• Ustalenia szybkoœci pracy procesora i pamiêci

BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara
procesora.

Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie
bez uprzedniego powiadomienia.

Multi-Language Translation

Vlastnosti

Procesor

Základní deska 945PL-A je urèena pro procesory Pentium 4/Celeron D/Pentium D LGA775 a mùže
nabídnout následující vlastnosti:

• Určeno pro procesory Intel Pentium 4/Celeron D/Pentium D

• Podporuje taktování systémové sběrnice (FSB) na frekvenci 800/533 MHz

• Podporuje technologii CPU „Hyper-Threading“

Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl připojen ke
dvěma procesorům, protože je možné pracovat se dvěma toky programového kódu (vlákny) paralelně
najednou, přičemž jsou k dispozici samostatné „logické“ procesory umístěné v rámci jednoho
fyzického procesoru.

Čipová sada

Čipy northbridge (NB) 945PL a southbridge (SB) ICH7 jsou založeny na inovativní a škálovatelné
architektuře s ověřenou spolehlivostí a výkonností.

945PL (NB)

ICH7 (SB)

• Podporuje 32bitové adresování, umožòující CPU pøistupovat
k celému adresovému prostoru pamìti 2 GB.

• Podporuje maximální šířku pásma paměti 8,5 Gb/s v
dvoukanálovém prokládaném režimu.

• 2 GB/s přímé rozhraní DMI (Direct Media Interface) pro ICH7
(1 GB/s) v obou směrech.

• Podpora jednoho rozhraní PCI Express x16 pro grafiku, zcela
splòující základní požadavky standardu PCI Express, revize

1.0a.

• Podpora 256 Mb, 512 Mb a 1 Gb DDR2 technologií pro
zařízení x8 a x16

• Vylepšený řadič DMA, řadič přerušení a funkcí časovače

• Splňuje základní požadavky standardu PCI Express, revize

1.0a

• Splňuje požadavky standardu PCI 2.3

• Splňuje požadavky standardu Serial ATA II

• Integrované hostitelské řadiče USB 2.0 podporující až osm

portů

• Integrovaný řadič IDE podporující Ultra ATA100/66/33

Paměť

• Paměti DDR2 533/400 DDR SDRAM s dvoukanálovou architekturou DDR2

• Instalovat je možné až dvě DIMM moduly bez vyrovnávací pamìti

• Až 1 GB pamìti na jeden modul DIMM s maximální velikostí pamìti do 2 GB

Vestavění síťové rozhraní LAN (volitelně)

Vestavěné síťové rozhraní LAN nabízí následující možnosti:

• Podpora 100/10 MB/s N–cestného automatického přepínání provozu

• Podpora rozhraní PCI v2.2, 32bitové, 33MHz

• Podpora funkce Wake–on–LAN (WOL) a vzdálené aktivace

• Podpora plně duplexního řízení toku dat (IEEE 802.3x)

• Integrovaný transceiver 10/100/1000

• Podpora rozhraní PCI v2.3, 32bitové, 33MHz

• Plná podpora rozhraní IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Česky

1394a FireWire (volitelně)

• Podporuje požadavky standardu IEEE Std 1394-1995 pro vysoký výkon ro­zhraní

• Poskytuje dva kabelové porty 1394a, splňující požadavky standardu s
přenosovou rychlostí 400/200/100 Mbit/s, sériová sběrnice 1.0 a IEEE Std

1394a-2000

Zvuk (volitelně)

• Splňuje požadavky standardu AC’97 2.3 podpora 6kanálového

• 16bitový stereo plnì duplexní kodek se vzorkovací frekvencí 48 MHz

• Podpora dvojnásobné vzorkovací frekvence (96 kHz) pro přehrávání DVD
audio

• Kompatibilita s Direct Sound 3D

• Splňuje požadavky standardu Hi–Fi audiokodeku Intel, s podporou
8kanálového D/A převodníku s odstupem šumu od zvuku 95 dB

• Kompatibilita: 192/96/48/44,1 kHz s 24/20/16bitovým vzorkováním

• Napájení: Digitální: 3,3 V; Analogové: 3,3 V / 5,0 V

• Všechny analogové vstupní a výstupní konektory jsou stereo, plug & play

TM

Možnosti rozšíření

Základní deska je dodávána s následujícími možnostmi rozšíření

• Dvě patice PCI Express x16 pro grafickou kartu

• Jedna patice PCI Express x1

• Tři 32bitové patice PCI v2.3

• Jeden nízkoprofilový 40kolíkový konektor IDE podporující připojení dvou
zařízení standardu IDE

• Jedno rozhraní pro disketovou mechaniku

• Čtyři 7kolíkové konektory SATA

Základní deska 945PL-A podporuje sběrnici Ultra DMA s přenosovými rychlostmi 100/66/33 MB/
s.

Česky

Integrovaný vstup/výstup

Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:

• Dva porty PS/2 pro myš a klávesnici

• Jeden sériový port

• Jeden paralelní port

• Čtyři porty USB

• Jeden port 1394a (volitelně)

• Jeden port LAN (volitelně)

• Zvukové konektory pro mikrofon, zvukový vstup a výstup

Firmware BIOS

Základní deska využívá BIOS formy AMI, který uživateli umožňuje nakonfigurovat mnoho
systémových parametrů, včetně následujících:

• Řízení spotřeby

• Alarmy při spouštění systému

• Parametry CPU

• Časování CPU a paměti

Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence procesoru.

Některé technické parametry hardware a software se mohou měnit bez
předchozího upozornění.

Multi-Language Translation

Caracteristici

Procesorul

945PL-A utilizează Pentium 4/Celeron D/Pentium D de tipul LGA775, având următoarele
caracteristici:

• Funcţionează cu procesoare Intel Pentium 4/Celeron D/Pentium D

• Funcţionează cu bus sistem (FSB) de 800/533 MHz

• Este compatibilă cu unităţi centrale dotate cu tehnologia „Hyper-

Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum ar
exista două procesoare, putând fi rulate în paralel două fire, fiecare pe câte un procesor „logic”
separat, aflate pe acelaşi procesor fizic.

Threading”

Setul de chipuri

Seturile de chipuri 945PL Northbridge (NB) şi ICH7 Southbridge (SB) se bazează pe o
arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi performanţă.

945PL (NB)

ICH7 (SB)

• Sprijină adresarea host bus (bus gazdă) de 32 biţi, permiţând
unităţii centrale să acceseze întreaga cantitate de memorie
de 2 GB.

• Asigură a lărgime de bandă maximală de 8.5 GB/s în mod
mix cu canal dual.

• Interfaţă Direct Media (DMI) punct la punct pe 2 GB/s
pentru ICH7 (1 GB/s) în ambele direcţii.

• Sprijină PCI Express de 16x pentru interfaţa grafică, este
pe deplin compatibil cu versiunea 1.0a a specificaţiei de
bază PCI Express.

• Este compatibil cu tehnologiile de 256-Mb, 512-Mb şi 1­Gb DDR2, pentru unităţi de viteza 8x sau 16x

• Controler DMA îmbunătăţit, controler de întreruperi şi funcţii

de temporizare

• Compatibil cu specificaţia de bază PCI Express,

versiunea 1.0a

• Compatibil cu specificaţia PCI 2.3

• Compatibil cu specificaţie Serial ATA II

• Controler gazdă USB 2.0 integrat, care suportă cel mult

opt porturi USB 2.0

• Controler IDE integrat, suportând Ultra ATA100/66/33

Memoria

• Module DDR SDRAM DDR2 533/400 cu arhitectură DDR2 cu canal dual

• Poate funcţiona cu două module DIMM fără zonă tampon

• Poate funcţiona cu module DIMM de cel mult 1 GB, iar cantitatea maximă
de memorie este de 2 GB

Onboard LAN (opţional)

Onboard LAN are următoarele caracteristici:

• Suportă operaţii de autonegociere N-way de 100/10 MB/s

• Suportă PCI, versiunea 2.2, de 32 biţi, la 33 MHz

• Suport pentru funcţiile Wake-on-LAN şi trezire la distanţă

• Suportă controlul proceselor de duplex total (IEEE 802.3x)

• Unitate de emisie/recepţie 10/100/1000 integrat

• Suportă PCI, versiunea 2.3, de 32 biţi, la 33 MHz

• compatibil pe deplin cu standardul IEEE 802.3, IEEE 802.3u, IEEE

802.3ab

Multi-Language Translation

Română

1394a FireWire (Opţional)

• compatibil cu proviziile standardului de IEEE Std 1394-1995 pentru Înaltă
Performanţă

• asigură două porturi de cablu deplin compatibile cu 1394a la 400/200/100
Mbit/s Serial Bus 1.0 şi IEEE Std 1394a-2000

Audio (Opţional)

• Compatibil cu specificaţia AC’97 2.3 suportând cu 6 canale

• CODEC de 16 biţi stereo cu duplex complet şi viteză de eşantionare de
48 MHz

• Suport pentru viteză dublă de eşantionare (96 kHz) pentru redare audio
de pe DVD

• Compatibil cu Direct Sound 3D

• Compatibilitate cu specificaţia Intel High Definition Audio, suportând DAC
pe 8 canale cu raport sunet/paraziţi de 95 dB

• Compatibil cu: 192/96/48/44,1 kHz, la 24/20/16 biţi

• Sursă de alimentare: digitală: 3,3 V; analoagă: 3,3 V / 5,0 V

• Toate mufele analoage sunt cu redistribuire intrare şi ieşire stereo pentru
configurare automată analoagă

TM

Opţiuni de extindere

Placa de bază este dotată următoarele posibilităţi de extindere:

• Două sloturi PCI Express x16 pentru interfaţa grafică

• Un slot PCI Express x1

• Trei sloturi de 32 biţi compatibile PCI, versiunea 2.3

• O interfaţă IDE 40 cu profil plat care poate deservi două unităţi IDE

• O interfaţă pentru unitate floppy

• Patru conectoare SATA 7

Placa de bază 945PL-A suportă bus mastering UltraDMA cu viteze de transfer de
100/66/33 MB/s

Română

I/O integrată

Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:

• Două porturi PS/2, pentru mouse şi tastatură

• Un port serial

• Un port paralel

• Patru porturi USB

• Un port 1394a (opţional)

• Un port LAN (opţional)

• Mufe audio pentru microfon, intrare şi ieşire audio

Firmware BIOS

Placa de bază utilizează AMI BIOS, care permite utilizatorului să configureze mai mulţi
parametri ai sistemului, cum ar fi:

• Gestionarea energiei

• Alarme de trezire

• Parametri CPU

• Temporizare CPU şi memorie

Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă
ale procesorului.

Anumite specificaţii hardware şi elemente de software pot fi modificate fără
înştiinţare prealabilă.

Multi-Language Translation

Спецификация

Процесор

Дънната платка 945PL-A поддържа Pentium 4/Celeron D/Pentium D тип LGA775 със следните
спецификации:

• поддръжка на процесори Intel Pentium 4/Celeron D/Pentium D

• поддръжка на системна шина със скорост 800/533MHz

• поддръжка на процесори с технология “Hyper-Threading"

Технологията “
на два процесора, което дава възможност за паралелното изпълнение на две задачи на два
отделни “логически” процесора в един и същ физически процесор.

Hyper-Threading" позволява да се “излъже” операционната система, че работи

Чипсет

Чипсетът със северен мост 945PL (NB) и южен мост ICH7 (SB) е изграден на базата
на оригинална архитектура с възможност за надстройка с доказана надеждност и
производителност.

945PL (NB)

ICH7 (SB)

• 32-bit адресация на шината, което позволява на процесора
достъп към пълното адресно пространство на паметта 2
GB.

• Поддръжка на максимална скорост на трансфер на паметта

- 8.5 GB/s в двуканален режим на редуване (dual channel
interleaved mode).

• Директен медия интерфейс (DMI) 2 GB/s point-to-point към
ICH7, (1 GB/s във всяка посока).

• поддръжка на шина PCI Express x16 за графичен
интерфейс, напълно съвместима с шината PCI Express
Base ревизия 1.0a.

• поддръжка на технологии 256-Mb, 512-Mb и 1-Gb DDR2 за
x8 и x16 устройства

• подобрен DMA Контролер, контролер на прекъсванията и

часовник

• поддръжка на шината PCI Express Base, ревизия 1.0a

• поддръжка на шината PCI 2.3

• съвместимост със спецификацията Serial ATA II

• интегриран контролер USB 2.0 с поддръжка на до осем

порта USB 2.0

• интегриран контролер IDE с поддръжка на Ultra

ATA100/66/33

Памет

• Дву-канална архитектура на паметта DDR2 533/400 DDR SDRAM

• поддръжка на до два небуферирани DIMM слота

• до 1 GB памет на 1 DIMM канал с максимален капацитет 2 GB

Интегриран мрежов контролер (опция)

Спецификация на интегрирания мрежов контролер:

• Поддръжка на 100/10 MB/s, N-Way Auto-negotiation operation

• Поддръжка на

• Поддръжка на функции Wake-on-LAN и remote wake-up

• Поддръжка на

• Интегриран 10/100/1000 контролер

• Поддръжка на

• Пълна поддръжка на

PCI v2.2, 32-bit, 33-MHz

Full Duplex Flow Control (IEEE 802.3x)

PCI v2.3, 32-bit, 33-MHz

IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Multi-Language Translation

Български

1394a FireWire (Опция)

• Съответствие с условията на стандарта IEEE 1394-1995 за висока
производителност

• Включва два кабелни порта, напълно съвместими с 1394a , на скорост
400/200/100 Mbit/s, Serial Bus 1.0 и IEEE 1394a-2000

Аудио (Опция)

• Съвместимост със спецификациите на AC’97 Rev2.3 с поддръжка на 6-

канални

• 16-bit Stereo full-duplex CODEC с честота 48MHz

• Поддръжка на двойна честота (96KHz) при възпроизвеждане на DVD

audio

• съвместимост с Direct Sound 3D

• Съвместимост с Intel High Definition Audio, с поддръжка на 8-канални
цифрово-аналогови преобразователи със съотношение звук/шум 95dB

• съвместимост с: 192/96/48/44.1 KHz на 24/20/16 bits

• Захранване: Цифрово: 3.3V; Аналогово: 3.3V/5.0V

• Всички аналогови гнезда са стерео, с възможност за аналогов режим plug
& play

TM

Възможности за разширяване

Дънната платка има следните разширителни възможности:

• Два слота PCI Express x16 за графичен интерфейс

• Един слот PCI Express x1

• три слота 32-bit PCI v2.3

• един нископрофилен 40-pin IDE колектор с поддръжка на две IDE устройства

• един конектор за флопидисково устройство

• четири 7-pin SATA конектора

Дънната платка 945PL-A поддържа UltraDMA директно управление на шината със скорост на
обмен 100/66/33 MB/s

Български

Интегриран Вход/Изход контролер

Дънната платка има пълен набор от I/O портове и конектори:

• два PS/2 порта за мишка и клавиатура

• един сериен порт

• един паралелен порт

• четири USB порта

• един 1394a порт (опция)

• един LAN порт (опция)

• Аудио жакове за микрофон, линеен вход и линеен изход

BIOS Firmware

Дънната платка използва AMI BIOS с възможност за различни системни настройки,
включително

• управление на захранването

• Wake-up аларми

• параметри на процесора

• синхронизиране на процесора и паметта

настройка на скоростта на часовника на процесора

Хардуерните и софтуерни спецификации и параметри могат да бъдат
изменени без предупреждение.

Multi-Language Translation

Jellemző

Processzor

A 945PL-A LGA775 típusú Pentium 4/Celeron D/Pentium D számára készült, és a következő
jellemzőkkel bír:

• Intel Pentium 4/Celeron D/Pentium D processzorokkal működik

• 800/533 MHz sebességű rendszerbuszt (FSB) támogat

• Támogatja a „Hyper-Threading” technológiát használó központi

A „Hyper-Threading” technológia által az operációs rendszer úgy működik, mintha két
processzorral rendelkezne, ami két szál párhuzamos futását teszi lehetővé két független,
ugyanazon fizikai processzoron található „logikai” processzoron.

egységeket

Lapkakészlet

A 945PL Northbridge (NB) és ICH7 Southbridge (SB) lapkakészletek egy új és méretezhető,
nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.

945PL (NB)

ICH7 (SB)

• 32 bites host bus addressing-et (gazdabusz címzést) tesz
lehetővé, ami által a központi egység a teljes 2 GB-os címzési
tárhelyhez hozzáfér.

• Támogatja a 8.5 GB/s maximális memória-sávszélességet
kettős csatornájú, kevert módban.

• 2 GB/s pontról-pontra adatátvitelű Direct Media interfész
(DMI) az ICH7 (1 GB/s) számára mindkét irányban.

• Egy 16-szoros Express PCI-vel rendelkezik a grafikus
interfész számára, amely teljesen kompatibilis a PCI Express
alapspecifikáció 1.0a változatával.

• 256 Mb-os, 512 Mb-os és 1 Gb-os DDR2 technológiát
támogat 8- és 16-szoros eszközök esetében

• Fejlett DMA vezérlő, megszakításvezérlő és időzítő funkciók

• Kompatibilis a PCI Express alapspecifikáció 1.0a változatával

• Kompatibilis a PCI 2.3-as specifikációjával

• Kompatibilis a soros ATA II specifikációval

• Beépített USB 2.0 gazda vezérlő, legtöbb nyolc USB 2.0
portot támogat

• Beépített IDE vezérlő, amely az Ultra ATA100/66/33 technológiát
támogatja

Memória

• DDR2 533/400 DDR SDRAM modulok kétcsatornás DDR2 kiépítésben

• Két puffermentes DIMM egységgel működik

• Maximum 1 GB-os DIMM egységeket támogat, maximális memória 2 GB

Alaplapon levő LAN (választható)

Az alaplapon levő LAN jellemzői:

• 100/10 MB/s N-Way automatikus beállítással

• Támogatja a 32 bites, 33 MHz-es PCI 2.2-as változatát

• A Wake-on-LAN és a távoli ébresztés funkciók támogatása

• Támogatja a teljes duplex folyamatvezérlést (IEEE 802.3x)

• Integrált 10/100/1000 adó-vevő

• Támogatja a 32 bites, 33 MHz-es PCI 2.3-as változatát

• Teljesen kompatibilis az IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
szabvánnyal

Multi-Language Translation

Magyar

1394a FireWire (Opcionális)

• megfelel az IEEE Std 1394-1995 standard rendelekezéseinek magas telje­sítményhez

• két 1394a-nak teljesen megfelelő kábel portot biztosít 400/200/100 Mbit/s
sebességű Serial Bus 1.0-on és IEEE Std 1394a-2000-on

Audio (Opcionális)

• Megfelel az AC’97 2.3-as specifikációnak 6 csatornás támogat.

• 16 bites sztereo teljes duplex CODEC 48 MHz-es mintavételezési
sebsséggel

• Dupla mintavételezési arányú (96 kHz) DVD audio lejátszást teszt
lehetővé

• Kompatibilis a Direct Sound 3DTM technológiával

• Kompatibilis az Intel High Definition Audio előírásokkal, 8 csatornás DAC
támogatásával, 95 dB jel-zaj aránnyal

• Kompatibilitás: 192/96/48/44,1 KHz, 24/20/16 biten

• Tápforrás: digitális: 3,3 V; analóg: 3,3 V / 5,0V

• Az összes analóg csatlakozó sztereó bemenetű és kimenetű analóg
azonnali felismerés támogatására

Bővítési lehetőségek

Az alaplap a következő bővítési lehetőségekkel rendelkezik:

• Két 16-szeres PCI Express foglalat a grafikus interfész számára

• Egy 1-szeres PCI Express foglalat

• Három 32 bites, a PCI 2.3-as változatával kompatibilis foglalat

• Egy 40 tűs lapos IDE foglalat, amely két IDE eszközt képes kiszolgálni

• Egy hajlékonylemez meghajtó interfész

• Négy 7 tűs SATA csatlakozó

A 945PL-A alaplap támogatja az UltraDMA bus mastering megoldást, 100/66/33 MB/s
sebességen

Magyar

Beépített I/O

Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:

• Két PS/2 port az egér és a billentyűzet számára

• Egy soros port

• Egy párhuzamos port

• Négy USB port

• Egy 1394a port (választható)

• Egy LAN port (választható)

• Audio csatlakozók mikrofon, bemenet és kimenet számára

BIOS Firmware

Az alaplapon levő AMI BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja
be, például:

• Energiagazdálkodás

• Ébresztési riasztások

• CPU paraméterek

• CPU és memória időzítés

A firmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.

Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül
módosulhatnak.

Multi-Language Translation