ECS 945G-M3 (3.0) User Manual

Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Cor­poration.
Other product names used in this manual are the properties of their respective owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason­able protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Describes features of the motherboard.
Go to
H
page 1
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Describes installation of motherboard components.
Go to
Provides information on using the BIOS Setup Utility.
Go to
Describes the motherboard software
Go to
H
H
H
page 7
page 27
page 49
Preface
TT
ABLE OF CONTENTSABLE OF CONTENTS
T
ABLE OF CONTENTS
TT
ABLE OF CONTENTSABLE OF CONTENTS
Preface i
iii
Chapter 1
Introducing the Motherboard 1
Introduction.................................................................................................1
Feature..........................................................................................................2
Motherboard Components........................................................................4
1
Chapter 2
Installing the Motherboard 7
Safety Precautions......................................................................................7
Choosing a Computer Case.......................................................................7
Installing the Motherboard in a Case......................................................7
Checking Jumper Settings.........................................................................8
Setting Jumpers..............................................................................8
Checking Jumper Settings..............................................................9
Jumper Settings..............................................................................9
Connecting Case Components...............................................................10
Front Panel Header.....................................................................12
Installing Hardware...................................................................................13
Installing the Processor...............................................................13
Installing Memory Modules.........................................................15
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17
Installing a Floppy Diskette Drive...............................................18
Installing Add-on Cards..............................................................19
Connecting Optional Devices......................................................20
Connecting I/O Devices.........................................................................25
7 7
7
7 7
Chapter 3 27
Using BIOS 27
About the Setup Utility........................................................................... 27
The Standard Configuration.......................................................27
Entering the Setup Utility..............................................................27
Updating the BIOS.......................................................................29
Using BIOS................................................................................................29
Standard CMOS Features...........................................................30
Advanced BIOS Features.............................................................32
Advanced Chipset Features.........................................................35
iv
Integrated Peripherals.................................................................37
Power Management Setup...........................................................41
PNP/PCI Configurations.............................................................43
PC Health Status..........................................................................44
Frequency Control.......................................................................45
Load Fail-Safe Defaults...............................................................46
Load Optimized Defaults Option.................................................46
Set Password...............................................................................46
Save & Exit Setup.........................................................................47
Exit Without Saving.......................................................................47
Chapter 4
49 49
49
49 49
Using the Motherboard Software 49
About the Software CD-ROM...............................................................49
Auto-installing under Windows 2000/XP.............................................49
Running Setup.............................................................................50
Manual Installation..................................................................................52
Utility Software Reference.......................................................................52
Multi-Language Translation
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing the motherboard. This motherboard is a high performance, en­hanced function motherboard designed to support the LGA775 socket Intel CoreTM2 Duo / Pentium D/Pentium 4/Celeron D processors for high-end business or personal desktop markets.
The motherboard incorporates the 945G Northbridge (NB) and ICH7 Southbridge (SB) chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 1066/800/533 MHz using a scalable FSB Vcc_CPU. The memory controller supports DDR2 memory DIMM frequencies of 667/533/400. It supports two DDR2 Sockets with up to maximum memory of 2 GB. DDR2 memory bandwidth of 5.3 GB/s in single-channel is supported, or 10.7 GB/ s in dual-channel interleaved mode assuming DDR2 667 MHz. High resolution graphics via one PCI Express slot, intended for Graphics Interface, is fully compliant to the PCI Express Base Specification revision 1.0a.
The ICH7 Southbridge supports two PCI slots which are PCI 2.3 compliant. In addition, one PCI Express x1 slot is supported, fully compliant to the PCI Express Base Specification, Revision 1.0a. It implements an EHCI compliant interface that provides 480 Mb/s band­width for eight USB 2.0 ports, integrates Azalia codec supporting Azilia standard that features an 8-channel High Definition Audio output. One onboard IDE connector supports 2 IDE devices in Ultra ATA100/66/33 mode. The Southbridge integrates a Serial ATA host controller that is SATA II compliant, supporting four SATA ports with maximum transfer rate up to 3.0 Gb/s each.
The motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and keyboard connectors, COM1, LPT1, one VGA port, four USB ports, one optional LAN port, one optional 1394 port and audio jacks for microphone, line-in and 8­ch line out.
1
Introducing the Motherboard
2
Feature
Processor
The motherboard uses an LGA775 type of Intel CoreTM2 Duo / Pentium D/Pentium 4/ Celeron D that carries the following features:
Accommodates Intel CoreTM2 Duo/Pentium D/Pentium 4/Celeron D proce- ssors
Supports a system bus (FSB) of 1066/800/533MHZ
Supports “Hyper-Threading” technology CPU
“Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical” processors within the same physical processor.
Chipset
The 945G Northbridge (NB) and ICH7 Southbridge (SB) chipsets are based on an innovative and scalable architecture with proven reliability and performance.
945G (NB)
Supports 32-bit host bus addressing, allowing the CPU to access the entire 4 GB of the memory address space.
2 GB/s point-to-point Direct Media Interface (DMI) to ICH7 (1 GB/s)each direction.
Supports one PCI Express x16 for Graphics Interface, fully compliant to the PCI Express Base Specification revision
1.0a.
Supports 256-Mb, 512-Mb and 1-Gb DDR2 technologies for x8 and x16 devices
Supports high quality 3D setup, Render Engine and high­quality texture engine
ICH7 (SB)
Enhanced DMA Controller, interrupt controller, and timer func­tions
Compliant with PCI Express Base Specification, Revision
1.0a
Compliant with PCI 2.3 specificaiton
Compliant with Serial ATA II specification
Integrated USB 2.0 Host Controller supporting up to eight USB 2.0 ports
Integrated LAN controller
Compliant with AC’97/Intel High Definition Audio Codec(s) supporting 8-channel audio outputs
Integrated IDE controller supports Ultra ATA100/66/33
Memory
Supports DDR2 667/533/400 DDR SDRAM with Dual-channel architecture
Accommodates two unbuffered DIMMs
Up to 1 GB per DIMM with maximum memory size up to 2 GB
Graphics
3D Setup and Render Engine
Zone Rendering Support
High Quality Texture Engine
Introducing the Motherboard
1394a FireWire (Optional)
Compliant with single chip hostcontroller for IEEE Std 1394-1995 and IEEE 1394a-2000
Integrated 400 Mbit 2-Port PHY for the PCI BUS
3.3V Power Supply with 5V Tolerant Inputs
Onboard LAN (Optional)
The onboard LAN controller provides the following features:
Integrated 10/100/1000 transceiver
Supports PCI v2.3, 32-bit, 33/66MHz
Supports fully with IEEE802.3, IEEE802.3u and IEEE802.3ab
• Supports 10/100 /Mb/s N-Way Auto negotiation operation
Half/Full deplux capacity
Supports wake-On-LAN(WOL)function and remote wake-up
Audio (Optional)
8-channels of DAC support 24/20/16-bit PCM format for 7.1 audio solution
Support 192K/96K/48K/44.1KHz DAC sample rate
Power support: Digital: 3.3V; Analog: 3.3V~5.25V
Meets Micrsoft WHQL/WLP 2.0 audio requirements
Direct Sound 3DTM compatible
Dolby Digital Encorder output for consumer electronic application
3
Compliant with Intel High Definition Audio, supporting 8-channel DACs with 95dB S/N ratio
Compabilities: 192/96/48/44.1 KHz with 24/20/16 bits
Power support: Digital: 3.3V; Analog: 3.3V/5.0V
All analog jacks are stereo input and output re-tasking for analog plug & play
Meets Micrsoft WHQL/WLP 2.0 audio requirements
Direct Sound 3DTM compatible
Dolby Digital Encorder output for consumer electronic application
Compliant with the AC’97 v2.3 CODEC
Supports 6-channel audio CODEC designed for PC multimedia systems
Provides three analog line-evel stereo inputs with 5-bit volum control: Line-in ,CD,AUX
Meets Micrsoft WHQL/WLP 2.0 audio requirements
Expansion Options
The motherboard comes with the following expansion options:
One PCI Express x16 slot for Graphic Interface
One PCI Express x1 slot
Two 32-bit PCI v2.3 compliant slots
One 40-pin IDE low profile header that support two IDE devices
One floppy disk drive interface
Four 7-pin SATA connectors
The motherboard supports UDMA bus mastering with transfer rates of 100/66 MB/s.
Introducing the Motherboard
4
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
Two PS/2 ports for mouse and keyboard
One serial port
One parallel port
One VGA port
Four USB ports
One 1394 port (optional)
One LAN port (optional)
Audio jacks for microphone in, line-in and 8-ch High Definition Audio output
BIOS Firmware
This motherboard uses Award BIOS that enables users to configure many system features including the following:
Power management
Wake-up alarms
CPU parameters
CPU and memroy timing
The firmware can also be used to set parameters for different processor clock speeds.
Some hardware specifications and software items are subject to change with out prior notice.
Introducing the Motherboard
Motherboard Components
5
Introducing the Motherboard
6
Table of Motherboard Components
LABEL COMPONENT
1 CPU Socket LGA775 socket for Intel CoreTM2 Duo/Pentium
2 CPU_FAN CPU cooling fan connector
3 DIMM1~2 240-pin DDR2 SDRAM slots
4 IRDA Infrared header 5 FDD Floppy diskette drive connector
6 ATX1 Standard 24-pin ATX power connector
7 IDE1 Primary IDE channel
D/Pentium 4/Celeron D
8 CHS_FAN System cooling fan connector
9 CLR_CMOS Clear CMOS jumper
10 EL** LED header
11 SATA1~4 Serial ATA connectors
12 PANEL1 Front panel switch/LED header
13 JLPC** Low pin count header
14 USB1~2 Front Panel USB headers
15 1394A2* IEEE 1394a header 16 BIOS_WP BIOS flash protect jumper
17 COM2* Onboard Serial port header 18 WOL1* Wake On LAN connector
19 SPDIFO or S/PDIF** SPDIF out header 20 F_AUDIO Front panel audio header
21 AUX_IN* Auxiliary In connector
22 PCI1~2 32-bit add-on card slots
23 PCIE1 PCI Express x1 slot
24 PCIEX16 PCI Express slot for graphics interface
25 SYS_FAN System cooling fan connector
26 ATX12V Auxiliary 4-pin power connector
* Stands for optional components
** Please be noted S/PDIF header is for special customers.
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Safety Precautions
Follow these safety precautions when installing the motherboard
Wear a grounding strap attached to a grounded device to avoid damage from static electricity
Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard
Leave components in the static-proof bags they came in
Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies with the specifications for the Micro ATX system case. First, some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required. Secondly, this motherboard supports one or two floppy diskette drives and two enhanced IDE drives. Make sure that your case has sufficient power and space for all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.
This motherboard carries an Micro ATX form factor of 244 x 244 mm. Choose a case that accommodates this form factor.
7
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in a case.
Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.
The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.
This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT
SHORT OPEN
Installing the Motherboard
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
9
Jumper Settings
Jumper
CLR_CMOS
Type
Description Setting (default)
1-2: NORMAL
3-pin
CLR_CMOS
2-3: CLEAR CMOS
Before clearing the CMOS, make sure to turn off the system.
OPEN : WRITE UNPROTECT
BIOS_WP
SHORT:WRITE PROTECT
2-pin
FLASH
PROTECT
Installing the Motherboard
1
CLR_CMOS
BIOS_WP
10
Connecting Case Components
After you have installed the motherboard into a case, you can begin con­necting the motherboard components. Refer to the following:
1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the system cooling fan connector to SYS_FAN. 3 Connect the case switches and indicator LEDs to the PANEL1. 4 Connect the standard power supply connector to ATX1. 5 Connect the auxiliary case power supply connector to ATX12V.
6 Connect the case cooling fan connector to CHS_FAN .
Connecting 20/24-pin power cable
Users please note that the 20-pin and 24-pin power cables can both be connected to the ATX1 connector. With the 20-pin power cable, just align the 20-pin power cable with the pin 1 of the ATX1 connector. However, using 20-pin power cable may cause the system to become unbootable or unstable because of insufficient electricity. A minimum power of 300W is recommended for a fully-configured system.
With ATX v1.x power supply, users please note that when installing 20-pin power cable, the latche of power cable falls on the left side of the ATX1 connector latch, just as the picture shows.
20-pin power cable
With ATX v2.x power supply , users please note that when installing 24-pin power cable, the latches of power cable and the ATX1 match perfectly.
24-pin power cable
Installing the Motherboard
CPU_FAN: FAN Power Connector
Pin Signal Name Function
1 GND System Ground 2 +12V Power +12V 3 Sense Sensor 4 PWM CPU FAN control
Users please note that the fan connector supports the CPU cooling fan of
1.1A ~ 2.2A (26.4W max) at +12V.
SYS_FAN/CHS_FAN: FAN Power Connector(optional)
Pin Signal Name Function
1 GND System Ground 2 +12V Power +12V 3 Sense Sensor
ATX1: ATX 24-pin Power Connector
Pin Signal Name Pin Signal Name
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V 3 Ground 15 Ground
4 +5V 16 PS_ON
5 Ground 17 Ground
6 +5V 18 Ground 7 Ground 19 Ground 8 PWRGD 20 -5V
9 +5VSB 21 +5V
10 +12V 22 +5V 11 +12V 23 +5V
12 +3.3V 24 Ground
11
ATX12V: ATX 12V Power Connector
Pin Signal Name
1 Ground
2 Ground 3 +12V
4 +12V
Installing the Motherboard
12
Front Panel Header
The front panel header (PANEL1) provides a standard set of switch and LED headers commonly found on ATX or Micro ATX cases. Refer to the table below for information:
Pin Signal Function Pin Signal Function
1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)
3 HD_LED_N Hard disk LED(- )
5 RST_SW_N Reset Switch(-)
7 RST_SW_P Reset Switch(+)
9 RSVD Reserved
* MSG LED (dual color or single color)
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.
4 FP PWR/SLP *MSG LED(-)
6 PWR_SW_P Power Switch(+)
8 PWR_SW_N Power Switch(-)
10 Key No pin
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentary­contact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal de­bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.
Installing the Motherboard
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.
On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.
Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change these settings by making changes to jumpers on the motherboard, or changing the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.
Warning: Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.
13
This motherboard has a LGA775 socket. When choosing a processor, consider the perfor­mance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.
Installing the Motherboard
14
CPU Installation Procedure
The following illustration shows CPU installation components.
A. Read and follow the instructions shown on the sticker on the CPU cap. B. Unload the cap
· Use thumb & forefinger to hold the lifting tab of the cap.
· Lift the cap up and remove the cap completely from the socket.
C. Open the load plate
· Use thumb & forefinger to hold the hook of the lever, pushing down and pulling aside unlock it.
· Lift up the lever.
· Use thumb to open the load plate. Be careful not to touch the contacts.
D. Install the CPU on the socket
· Orientate CPU package to the socket. Make sure you match triangle marker to pin 1 location.
E. Close the load plate
· Slightly push down the load plate onto the tongue side, and hook the lever.
· CPU is locked completely.
F. Apply thermal grease on top of the CPU.
G. Fasten the cooling fan supporting base onto the CPU socket on the motherboard.
H. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.
1. To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink sup plied. The form and size of fan/heatsink may also vary.
2. DO NOT remove the CPU cap from the socket before installing a CPU.
3. Return Material Authorization (RMA) requests will be accepted only if the motherboard comes with thecap on the LGA775 socket.
Installing the Motherboard
Installing Memory Modules
This motherboard accomodates four memory modules. It can support two 240-pin 1.8V DDR2 667/533/400. The total memory capacity is 2 GB.
DDR2 SDRAM memory module table
15
CPU FSB
533/800MHz
533/800/1066MHz
800/1066MHz
You must install at least one module in any of the two slots. Each module can be installed with 256 MB to 1 GB of memory; total memory capacity is 2 GB.
Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.
Memory module
DDR2 400
DDR2 533 266MHz DDR2 667 333MHz
Memory Bus
200 MHz
Installation Procedure
Refer to the following to install the memory modules.
1 This motherboard supports unbuffered DDR2 SDRAM . 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.
4 Check that the cutouts on the DIMM module edge connector match the notches
in the DIMM slot.
5 Install the DIMM module into the slot and press it firmly down until it seats
correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.
6 Install any remaining DIMM modules.
Installing the Motherboard
16
Table A: DDR2(memory module) QVL (Qualified Vendor List)
The following DDR2 400/533/667 memory modules have been tested and qualified for use
with this motherboard.
Type Size Vendor Module Name
DDR2
400
DDR2
533
DDR2
667
256MB
512MB
256MB
512MB
1GB
256MB
512MB
Micron MT8HTF3264AG-40EB3 CL3 SS
Hynix HYMP532U646-E3 AA
Nanya NT256T64UH4A0F-5A CL3
Hynix HYMP564U648-E3 AA
Nanya NT512T64U88A0F-5A CL3
Samsung M378T3253FG0-CCC
Elixir M2U25664TUH4A0F-37B CL4
Infineon HYS64T32000HU-3.7-A
Kingston KVR533D2N4
Samsung M378T3253FG0-CD5 CL4
Elixir M2U51264TU88A0F-37B
Kingston KVR533D2N4
SAMSUNG M378T6553BGO-CD5
Infineon HYS64T128020HU-3.7-A
NANYA NT512T64U88A0BY-3C
ELPIDA EBE52UC8AAFV-DF-E
Installing the Motherboard
Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive
This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive.
About IDE Devices
Your motherboard has one IDE channel interface. An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.
You must orient the cable connector so that the pin1 (color) edge of the cable correspoinds to the pin 1 of the I/O port connector.
IDE1: IDE Connector
This motherboard supports four high data transfer SATA ports with each runs up to 150 MB/s. To get better system performance, we recommend users connect the CD-ROM to the IDE channel, and set up the hard dives on the SATA ports.
17
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.
About SATA Connectors
Your motherboard features four SATA connectors supporting a total of four drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with an SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.
SATA cable (optional)
SATA power cable (optional)
Installing the Motherboard
18
Refer to the illustration below for proper installation:
1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
This motherboard does not support the “Hot-Plug” function.
Installing a Floppy Diskette Drive
The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.
FDD: Floppy Disk Connector
This connector supports the provided floppy drive ribbon cable. After connecting the single end to the onboard floppy connector, connect the remaining plugs on the other end to the floppy drives correspondingly.
Installing the Motherboard
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabili­ties by adding hardware that performs tasks that are not part of the basic system.
19
PCIEX16 slot
PCIE1
slot
PCI 1/2 slots
The one PCI Express x16 slot is fully compliant to the PCI Express Base Specification revision 1.0a as well.
The PCI Express x1 slot is fully compliant to the PCI Express Base Specifi­cation revision 1.0a as well.
This motherboard is equipped with two standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.
Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.
Installing the Motherboard
20
Follow these instructions to install an add-on card:
1 Remove a blanking plate from the system case corresponding to the slot you
are going to use.
2 Install the edge connector of the add-on card into the expansion slot. Ensure
that the edge connector is correctly seated in the slot.
3 Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapt­ers, you have to install drivers and software before you can begin using the add-on card.
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
Installing the Motherboard
F_AUDIO: Front Panel Audio header for Azalia
This header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access.
21
Pin Signal Name
Pin Signal Name Function
1 PORT 1L 2 GND
Pin Signal Name
Pin Signal Name
3 PORT 1R 4 PRESENCE# 5 PORT 2R 6 Sense1_return
7 SENSE_SEND 8 KEY
9 PORT 2L 10 Sense2_return
SATA1/2/3/4: Serial ATA connectors
These connectors are use to support the new Serial ATA devices for the highest date transfer rates (3.0 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.
Pin Signal Name
Pin Signal Name Function
1 Ground 2 TX+
Pin Signal Name
3 TX- 4 Ground 5 RX- 6 RX+
7 Ground - -
SPDIFO: SPDIF out header (optional)
This is an optional header that provides an SPDIFO (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coxial connector.
Pin Signal Name
Pin Signal Name Function
1 SPDIFOUT
2 +5V 3 Key
4 GND
S/PDIF: SPDIF out header (optional)
This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coxial connector.
Pin Signal Name
1 +5V
2 Key 3 SPDFOUT
4 GND
Installing the Motherboard
22
1394A2: IEEE 1394A header (optional)
Connect this header to any device with IEEE 1394a interface.
Pin Signal Name
Pin Signal Name Function
1 TPA1P 2 TPA1M
3 GND 4 GND 5 TPB1P 6 TPB1M
7 CPWR2 8 CPWR2
9 Key 10 GND
Pin Signal Name
AUX_IN: Auxliary In header (optional)
Pin Signal Name Function
1 AUX_L AUX In left channel
2 GND Ground
3 GND Ground 4 AUX_R AUX In right channel
WOL1: Wake On LAN connector (optional)
If you have installed a LAN card, use the cable provided with the card to plug into the WOL connector onboard. This enables the Wake On LAN (WOL) feature. When your system is in a power-saving mode, any LAN signal automatically resumes the system. You must enable this item using the Power Management page of the Setup Utility in the BIOS. See Chapter 3 for more information.
Pin Signal Name Function
1 5VSB +5V stand by power
2 GND Ground
3 Ring# Wake up signal (low active)
IRDA: Infrared header
The motherboard supports an Infrared (IRDA) data port. Infrared ports allow the wireless exchange of information between your computer and similarly equipped devices such as printers, laptops, Personal Digital Assistants (PDAs), and other computers.
Pin Signal Name
Pin Signal Name Function
1 VCC
2 Key
3 IRRX
4 GND
5 IRTX
Installing the Motherboard
EL: LED headers (optional)
This is an optional header that is used to switch on and off SATA signal light.
Pin Signal Name
Pin Signal Name
Pin Signal Name
Pin Signal Name 1 GPIO26
2
GND
3 EL_GRN_LED
4 GND
5 EL_YLW_LED
6 KEY
USB1/2: Front Panel USB headers
The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Pin Signal Name Function
1 USBPWR Front Panel USB Power 2 USBPWR Front Panel USB Power 3 USB_FP_P0- USB Port 0 Negative Signal
4 USB_FP_P1- USB Port 1 Negative Signal 5 USB_FP_P0+ USB Port 0 Positive Signal 6 USB_FP_P1+ USB Port 1 Positive Signal
7 GND Ground
8 GND Ground 9 Key No pin 10 USB_FP_OC0 Overcurrent signal
Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hang-up.
COM2: Onboard serial port connector (optional)
Connect a serial port extension bracket to this header to add a second serial port to your system.
Pin Signal Name Function
1 DCDB Data Carrier Detect 2 SINB Serial Input
3 SOUTB UART B Serial Output
4 DTRB UART B Data Terminal R eady 5 GND Ground 6 DSRB Data Set Ready
7 RTSB RART B Request to Send
8 CTSB Clear to Send 9 RI Ring Indicator 10 Key No pin
23
Installing the Motherboard
24
JLPC(Low pin count header ) (optional)
Pin No. Symbol Pin No. Symbol
1 CK_P_33M_JLPC 2 GND
3
FWH4 4 KEY
5 PCIRST_L1 6 SMBDATA
7 FWH3
9 VCC3
8 FWH2
1 0 FWH1 11 FWH0 12 GND 13 PENABLE 14 NC
15
3VSBY 16 SIRQ
17 GND 18 GND
19 LPCPD_L 20 SMBCLK
Installing the Motherboard
Connecting I/O Devices
The backplane of the motherboard has the following I/O ports:
PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.
25
Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications
Serial Port Use the COM port to connect serial devices such as mice or (COM1) fax/modems. COM1 is identified by the system as COM1/3.
VGA Port Connect your monitor to the VGA port.
1394a Port (optional) Use the 1394a port to connect to any firewire device.
LAN Port Connect an RJ-45 jack to the LAN port to connect your computer
USB Ports Use the USB ports to connect USB devices.
Audio Ports
This concludes Chapter 2. The next chapter covers the BIOS.
devices.
to the Network.
Use the audio jacks to connect audio devices. The D port is for stereo line-in signal, while the F port is for microphone in signal. This motherboard supports 8-channel audio devices that corre­spond to the A, B, C, and E port respectively. In addition, all of the 3 ports, B, C, and E provide users with both right & left channels individually. Users please refer to the following note for specific port function definition.
A: Center & Woofer D: Line-in B: Back Surround E: Front Out C: Side Surround F: Mic_in Rear
The above port definition can be changed to audio input or audio output by changing the driver utility setting.
Installing the Motherboard
26
Memo
Installing the Motherboard
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s configura­tion status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
Hard drives, diskette drives and peripherals
Video display type and display options
Password protection from unauthorized use
Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
27
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
when changing the system configuration
when a configuration error is detected and you are prompted to make changes to the Setup Utility
when trying to resolve IRQ conflicts
when making changes to the Power Management configuration
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:
Using BIOS
28
Press DEL to enter SETUP
Pressing the delete key accesses the BIOS Setup Utility:
Phoenix-AwardBIOS CMOS Setup Utility:
Standard CMOS Features
Advanced BIOS Features Load Fail-Safe Defaults
Advanced Chipset Features Load Optimized Defaults
Integrated Peripherals Set Password
Power Management Setup Save & Exit Setup
PnP/PCI Configurations Exit Without Saving
PC Health Status
Esc: Quit F10: Save & Exit Setup
Time, Date, Hard Disk Type...
Frequency/Voltage Control

BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY FUNCTION
ESC Exits the current menu

 Scrolls through the items on a menu

+/-/PU/PD Modifies the selected field’s values
F10 Saves the current configuration and exits setup
F1 Displays a screen that describes all key functions
F5 Loads previously saved values to CMOS
F6 Loads a minimum configuration for troubleshooting
F7 Loads an optimum set of values for peak performance
: Select Item
Using BIOS
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:
1 If your motherboard has a BIOS protection jumper, change the setting to allow
BIOS flashing.
2 If your motherboard has an item called Firmware Write Protect in Advanced
BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.
3 Create a bootable system disk. (Refer to Windows online help for information
on creating a bootable system disk.)
4 Download the Flash Utility and new BIOS file from the manufacturer’s Web
site. Copy these files to the system diskette you created in Step 3.
5 Turn off your computer and insert the system diskette in your
computer’s diskette drive. (You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the floppy diskette drive first.)
6 At the A:\ prompt, type the Flash Utility program name and press <Enter>. 7 Type the filename of the new BIOS in the “File Name to Program” text box.
Follow the onscreen directions to update the motherboard BIOS.
8 When the installation is complete, remove the floppy diskette from the diskette
drive and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.
29
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.
Some options (marked with a triangle values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a

triangle
 .


) lead to submenus that enable you to change the

Using BIOS
30
Standard CMOS Features
This option displays basic information about your system.
Phoenix-AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy) Time (hh:mm:ss) 9 : 33 : 26
IDE Channel 0 Master
 
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
Drive A [1.44M, 3.5 in.] Floppy 3 Mode Support [Disabled]
Video [EGA/VGA] Halt On [All Errors]
Base Memory 640K Extended Memory 65535K Total Memory 1024K
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Date and Time
The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.
IDE Devices (None)
Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices (Master and Slave). Use these items to configure each device on the IDE channel.
This motherboard features four SATA connectors supporting four SATA drives. SATA refers to Serial ATA (Advanced Technology Attachment), the standard interface for the IDE hard drives which are currently used in most PCs.
Wed, Jan 19 2005
Item Help
Menu Level
Change the day, month, year and century
Phoenix-AwardBIOS CMOS Setup Utility
IDE Channel 0 Maser
IDE HDD Auto-Detection [Press Enter]
IDE Prinmary Master [Auto] Access Mode [Auto]
Capacity 0MB
Cylinder 0 Head 0 Precomp 0 Landing Zone 0 Sector 0
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Item Help
Menu Level
To auto-detect the HDD’s size, head... on this channel
Using BIOS

IDE HDD Auto-Detection
Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically detect and configure an IDE device on the IDE channel.
If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Choose the line that lists LBA for an LBA drive.
IDE Channel 0/1 Master/Slave IDE/Extended IDE Drives (Auto)
Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel. If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below. Please noted that if you choose IDE Channel 2/3 Master, the item may change to Extended IDE Drive.
Refer to your drive’s documentation or look on the drive casing if you need to obtain this information. If no device is installed, change the value to None.
Before attempting to configure a hard disk drive, ensure that you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk.
Access Mode (Auto)
This item defines ways that can be used to access IDE hard disks such as LBA (Large Block Addressing). Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive. If you choose IDE Channel 2/3 Master, the item only have Large and Auto.
Press <Esc> to return to the Standard CMOS Features page.
31
Drive A (1.44M, 3.5 in.)
The item defines the characteristics of any diskette drive attached to the system. You can connect one or two diskette drives.
Floppy 3 Mode Support (Disabled)
Floppy 3 mode refers to a 3.5-inch diskette with a capacity of 1.2 MB. Floppy 3 mode is sometimes used in Japan.
Video (EGA/VGA)
This item defines the video mode of the system. This motherboard has a built-in VGA graphics system; you must leave this item at the default value.
Halt On (All Errors)
This item defines the operation of the system POST (Power On Self Test) routine. You can use this item to select which types of errors in the POST are sufficient to halt the system.
Base Memory, Extended Memory, and Total Memory
These items are automatically detected by the system at start up time. These are display-only fields. You cannot make changes to these fields.
Press <Esc> to return to AwardBIOS CMOS Setup Utility page.
Using BIOS
32
3
3
3
3
3
3
Advanced BIOS Features
This option defines advanced information about your system.
Phoenix-AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature [Press Enter]
Hard Disk Boot Priority [Press Enter] CPU L1 & L2 Cache [Enabled] CPU L3 Cache [Enabled] Hyper-Threading Technology [Enabled] Quick Power On Self Test [Enabled] First Boot Device [Floppy] Second Boot Device [Hard Disk] Third Boot Device [CDROM] Boot Other Device [Enabled] Boot Up Floppy Seek [Disabled] Boot Up NumLock Status [On] Gate A20 Option [Fast] Typematic Rate Setting [Disabled]
x
Typematic Rate (Chars/Sec0 6
x
Typematic Delay (Msec) 250
Security Option [Setup]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
CPU Feature (Press Enter)
Users please note that this function is only available for Prescott CPUs. Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility CPU F eature
2
2
2
2
2
2
Item Help
Menu Level
Delay Prior to Thermal [16 Min] Thermal Management [Thermal Monitor 1] TM2 Bus Ratio [0 X] TM2 Bus VID [0.8375V] Limit CPUID MaxVal [Disabled] Execute Disable Bit [Enabled] Virtualization Technology [Enabled]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6”Fail-Safe Defaults F7:Optimized
Item Help
Menu Level
Thermal Monitor 1 (On die throtting)
Thermal Monitor 2 Ratio & VID transition

DelayPrior to Thermal (16 Min)
Enables you to set the delay time before the CPU enters auto thermal mode.
Thermal Management (Thermal Monitor 1)
This item displays CPU’s temperature and enables you to set a safe temperature to Prescott CPU.
TM2 Bus Ratio (0X)
This item represents the frequency (bus ratio) of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot).
Using BIOS
TM2 Bus VID (0.8375V)
This item represents the voltage of the throttled performance state that will be initiated when the on-die sensor goes from not hot to hot.
Limit CPUID MaxVal (Disabled)
This item can support Prescott CPUs for old OS. Users please note that under NT 4.0, it must be set “Enabled”, while under WinXP, it must be set “Disabled”.
Execute Disable Bit (Enabled)
This item is a security feature that helps you protect your CPU and operating system against malicious software executing code. This item is available when CPU supports the feature.
Intel Virtualization Technology (Enabled)
When enabled, a VMM can utilize the additional hardware capabilities provided by Vandor pool Technology.
Hard Disk Boot Priority (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
1. Pri.Master:
2. Pri.Slave:
3. Sec. Master:
4. Sec. Slave:
5. USBHDD0:
6. USBHDD1:
7. USBHDD2:
8. Bootable Add-in Cards
Item Help
Menu Level
Use < > or < >
to select a device, then press <+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

33

: Move PU/PD+/-/:Change Priority F10:Save ESC:Exit
CPU L1&L2 Cache (Enabled)
All processors that can be installed in this mainboard use internal level 1 (L1) and external level 2 (L2) cache memory to improve performance. Leave this item at the default value for better performance.
CPU L3 Cache (Enabled)
This item is only available when processors support L3. Some high-end processors support L3. If the CPU do support L3, you may set this item to enable or disable. Leave this item at the default value for better performance.
Hyper-Threading Technology (Enabled)
This item is only available when the chipset supports Hyper-Threading and you are using a Hyper-Threading CPU.
Quick Power On Self Test (Enabled)
Enable this item to shorten the power on testing (POST) and have your system start up faster. You might like to enable this item after you are confident that your system hardware is operating smoothly.
First/Second/Third Boot Device (Floppy/Hard Disk/CDROM)
Use these three items to select the priority and order of the devices that your system searches for an operating system at start-up time.
Using BIOS
34
Boot Other Device (Enabled)
When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices.
Boot Up Floppy Seek (Disabled)
If this item is enabled, it checks the size of the floppy disk drives at start-up time. You don’t need to enable this item unless you have a legacy diskette drive with 360K capacity.
Boot Up NumLock Status (On)
This item defines if the keyboard Num Lock key is active when your system is started.
Gate A20 Option (Fast)
This item defines how the system handles legacy software that was written for an earlier generation of processors. Leave this item at the default value.
Typematic Rate Setting (Disabled)
If this item is enabled, you can use the following two items to set the typematic rate and the typematic delay settings for your keyboard.
Typematic Rate (Chars/Sec): Use this item to define how many characters per second are generated by a held-down key.
Typematic Delay (Msec): Use this item to define how many milliseconds must elapse before a held-down key begins generating repeat characters.
Security Option (Setup)
If you have installed password protection, this item defines if the password is required at system start up, or if it is only required when a user tries to enter the Setup Utility.
APIC Mode (Enabled)
This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors.
OS Select For DRAM > 64 MB (Non-OS2)
This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default.
HDD S.M.A.R.T Capability (Disabled)
The S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system is a diag­nostics technology that monitors and predicts device performance. S.M.A.R.T. software resides on both the disk drive and the host computer.
Report No FDD For WIN 95 (Yes)
Set this item to the default if your are running a system with no floppy drive and using Windows 95; this ensures compatibility with the Windown 95 logo certification.
Small Logo (EPA) Show (Disabled)
This item enables or disables the display of the EPA logo during boot.
Press <Esc> to return to Advanced BIOS Features screen.
Using BIOS
Advanced Chipset Features
These items define critical timing parameters of the motherboard. You should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.
Phoenix-AwardBIOS CMOS Setup Utility Advanced Chipset Feature
35
DRAM Timing Selectable [By SPD] CAS Latency Time [Auto] DRAM RAS# to CAS# Delay [Auto] DRA M RAS# Prech arge [Auto] Precharge delay (tRAS) [Auto] System Memory Frequency [Auto] System BIOS Cacheable [Auto] Video BIOS Cacheable [Disabled]
** VGA Setting **
PEG/Onchip VGA Control [Auto] PEG Force X1 [Disabled] On-Chip Frame Buffer Size [8MB] DVMT Mode [DVMT] DVMT/FIXED Memory Size [128MB] Boot Display [Auto]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
DDR ADDR/CMD Rate (Auto)
Item Help
Menu Level
DRAM Timing Selectable (By SPD)
The value in this field depends on performance parameters of the installed memory chips (DRAM). Do not change the value from the factory setting unless you install new memory that has a different performance rating than the original DRAMs.
CAS Latency Time (Auto)
When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. Do not reset this field from the default value specified by the system designer.
DRAM RAS# to CAS# Delay (Auto)
This field allows you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Disabled gives faster performance; and Enabled gives more stable performance.
DRAM RAS# Precharge (Auto)
Select the number of CPU clocks allocated for the Row Address Strobe (RAS#) signal to accumulate its charge before the DRAM is refreshed. If insufficient time is allowed, refresh may be incomplete and data lost.
Precharge delay (tRAS)
The precharge time is the number of cycles it takes for DRAM to accumulate its charge before refresh.
System Memory Frequency (Auto)
This item sets the main memory frequency. When you use an external graphics card, you can adjust this to enable the best performance for your system.
Using BIOS
36
System BIOS Cacheable (Disabled)
This item allows the system to be cached in memory for faster execution. Enable this item for better performance.
Video BIOS Cacheable (Disabled)
The item allows the video BIOS to be cached in memory for faster execution.
PEG/Onchip VGA Control (Auto)
This item allows you to choose the primary display card.
PEG Force X1 (Disabled)
This item is used to select PCI Express X1 forcedly.
On-chip Frame Buffer Size (8MB)
This allows you to set the VGA frame buffer size.
DVMT Mode (DVMT)
DVMT is Dynamic Video Memory Technology. This item helps you select video mode.
DVMT/FIXED Memory Size (128MB)
DVMT is Dynamic Video Memory Technology; this item allows you to select a maximum size of dynamic amount usage of video memory. The system would configure the video memory depends on your application.
Boot Display (Auto)
This item is for Intel define ADD card only.
Using BIOS
Integrated Peripherals
These options display items that define the operation of peripheral components on the system’s input/output ports.
Phoenix-AwardBIOS CMOS Setup Utility
Integrated Peripherals
OnChip IDE Device [Press Enter] Onboard Device [Press Enter]
SuperIO Device [Press Enter]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
OnChip IDE Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
OnChip IDE Device
Item Help
Menu Level

37
IDE HDD Block Mode [Enabled] ATA 66/100 Cable Msg [Enabled] IDE DMA transfer access [Enabled] On-Chip Primary PCI IDe [Enabled] IDE Primary Master PIO [Auto] IDE Primary Slave PIO [Auto] IDE Primary Master UltraDMA [Auto] IDE Primary Slave UltraDMA [Auto] On-Chip Secondary PCI IDE [Enabled] IDE Secondary Master PIO [Auto] IDE Secondary Slave PIO [Auto] IDE Secondary Master UltraDMA [Auto] IDE Secondary Slave UltraDMA [Auto]
** On-Chip Serial ATA Setting**
On-Chip Serial ATA [Auto] SATA PORT Speed Settings [Disabled] PATA IDE Mode [Primary]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Item Help
Menu Level
If your IDE hard drive sup­ports block mode select Enabled for automatic detec­tion of the optimal number of block read/writes per sec­tor the drive can support

IDE HDD Block Mode (Enabled)
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support.
ATA66/100 Cable Msg (Enabled)
This item enables or disables the display of the ATA 66/100 Cable MSG.
Using BIOS
38
IDE DMA transfer Access (Enabled)
This item allows you to enabled the transfer access of the IDE DMA.
On-Chip Primary/Secondary PCI IDE (Enabled)
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately.
IDE Primary/Secondary Master/Slave PIO (Auto)
Each IDE channel supports a master device and a slave device. These four items let you assign which kind of PIO (Programmed Input/Output) is used by IDE devices. Choose Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 0-4.
IDE Primary/Secondary Master/Slave UltraDMA (Auto)
This mainboard supports UltraDMA technology, which provides faster access to IDE de­vices. If you install a device that supports UltraDMA, change the item on this list to Auto. You may have to install the UltraDMA driver supplied with this mainboard in order to use an UltraDMA device.
On-chip Serial ATA (Auto)
Enables and disables the built-in on-chip serial ATA.
SATA PORT Speed Settings (Disabled)
This item is used to select SATA I or SATA II device support forcedly.
PATA IDE Mode (Primary)
This item is used to set the PATA IDE mode. When set to Primary, P1 and P3 are Secondary; on the other hand, when set to Secondary, P0 and P2 are Primary.
Press <Esc> to return to the Integrated Peripherals page.
Using BIOS
Onboard Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Onboard Device
39
USB Controller [Enabled] USB 2.0 Supports [Enabled] USB Keyboard Support [Enabled] USB Mou se Support [Enabled] Azalia/AC97 Audio Select [Auto] Onboard LAN Device [Enabled] Onboard Lan Boot ROM [Disabled] Onboard 1394 Device [Enabled]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Item Help
Menu Level

USB Controller (Enabled)
Enables or disables the onboard USB controller. We recommend users keep the dafault value. Disabling it might cause the USB devices not to work properly.
USB 2.0 Supports (Enabled)
This item enables or disables the onboard USB 2.0.
USB Keyboard Support (Enabled)
Enable this item if you plan to use a keyboard connected through the USB port in a legacy operating system (such as DOS) that does not support Plug and Play.
USB Mouse Support (Enabled)
Enable this item if you plan to use a mouse connected through the USB port in a legacy operating system (such as DOS) that does not support Plug and Play.
Azalia/AC97 Audio Select (Auto)
Enables or disables the onboard Azalia/AC 97 audio function. Disable this item if you are going to install a PCI audio add-on card.
Onboard LAN Device (Enabled)
Enables and disables the onboard LAN.
Onboard LAN BOOT ROM (Disabled)
This item allows you to enable or disable the onboard LAN Boot ROM function.
Onboard 1394 Device (Enabled)
Enable this item if you plan to use the 1394 device.
Press <Esc> to return to the Integrated Peripherals page.
Using BIOS
Power Management Setup
12
12
12
12
This option lets you control system power management. The system has various power­saving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events.
Power Management Timeouts
The power-saving modes can be controlled by timeouts. If the system is inactive for a time, the timeouts begin counting. If the inactivity continues so that the timeout period elapses, the system enters a power-saving mode. If any item in the list of Reload Global Timer Events is Enabled, then any activity on that item will reset the timeout counters to zero.
Wake Up Calls
If the system is suspended or has been powered down by software, it can be resumed by a wake up call that is generated by incoming traffic to a modem, a LAN card, a PCI card, or a fixed alarm on the system realtime clock
ACPI Suspend Type [S3(STR)] Run VGABIOS if S3 Resume [Auto] Video Off Method [DPMS] Video Off In Suspend [Yes] Suspend Type [Stop Grant] MODEM Use IRQ [3] Soft-Off by PWR-BTTN [Instant-Off] CPU THRM-Throttling [50.0%] Resume by PCI PME [Enabled] Resume by Ring [Disabled] Resume by USB(S3) [Disabled] Resume by Alarm [Disabled]
X
Date (of Month) Alarm 0 Time (hh:mm:ss) 0 0 0
X
** Reload Global Timer Events**
Primary IDE0 [Disabled] Primary IDE 1 [Disabled] Secondary IDE0 [Disabled]
Phoenix-AwardBIOS CMOS Setup Utility Power Management Setup
Item Help
Menu Level
41
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
ACPI Suspend Type (S3(STR))
Use this item to define how your system suspends. In the default, S3 (STR), the suspend mode is a suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the system memory.
Run VGABIOS if S3 Resume (Auto)
This item allows the system to initialize the VGA BIOS from S3 (Suspend to RAM) sleep state.
Video Off Method (DPMS)
This item defines how the video is powered down to save power. This item is set to DPMS (Display Power Management Software) by default.
Video Off In Suspend (Yes)
This option defines if the video is powered down when the system is put into suspend mode.
Using BIOS
40
SuperIO Device (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
POWER ON Function [Hot Key] Hot Key Power ON [Ctrl-F12] Onboard FDC Controller [Enabled] Onboard Serial Port 1 [3F8/IRQ4] Onboard Parallel Port [378/IRQ7] Parallel Port Mode [ECP] ECP Mode Use DMA [3]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Phoenix-AwardBIOS CMOS Setup Utility
SuperIO Device
Item Help
Menu Level

POWER ON Function (Hot KEY)
This feature allows you to set the method by which your system can be turned on.
Hot Key Power On (Ctrl-F12)
When the POWER ON Function is set to Hot KEY, use this item to set the hot key combination that turns on the system.
Onboard FDC Controller (Enabled)
Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.
Onboard Serial Port 1 (3F8/IRQ4)
This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port 1 (COM1).
Onboard Parallel Port (378/IRQ7)
This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel port.
Parallel Port Mode (ECP)
Enables you to set the data transfer protocol for your parallel port. There are four options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), and ECP+EPP.
SPP allows data output only. Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) are bi-directional modes, allowing both data input and output. ECP and EPP modes are only supported with EPP- and ECP-aware peripherals.
ECP Mode Use DMA (3)
When the onboard parallel port is set to ECP mode, the parallel port can use DMA3 or DMA1.
Press <Esc> to return to the Integrated Peripherals page.
Using BIOS
42
Suspend Type (Stop Grant)
If this item is set to the default Stop Grant, the CPU will go into Idle Mode during power saving mode.
MODEM Use IRQ (3)
If you want an incoming call on a modem to automatically resume the system from a power­saving mode, use this item to specify the interrupt request line (IRQ) that is used by the modem. You might have to connect the fax/modem to the motherboard Wake On Modem connector for this feature to work.
Soft-Off by PWR-BTTN (Instant-Off)
Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec. then you have to hold the power button down for four seconds to cause a software power down.
CPU THRM-Throttling (50.0%)
Use this item to specify the CPU speed (at percentage) to slow down the CPU when it reach the predetermined overheat temperature.
Resume by PCI PME (Enabled)
This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected.
Resume by Ring (Disabled)
An input signal on the serial Ring Indicator (RI) line (in other words, an incoming call on the modem) awakens the system from a soft off state.
Resume by USB (S3)(Disabled)
This option allows the activity of the USB devices (keyboard and mouse) to wake-up the system from S3 sleep state.
Resume by Alarm (Disabled)
When set to Enabled, additional fields become available and you can set the date (day of the month), hour, minute and second to turn on your system. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time.
** Reload Global Timer Events **
Global Timer (power management) events are I/O events whose occurrence can prevent the system from entering a power saving mode or can awaken the system from such a mode. In effect, the system remains alert for anything that occurs to a device that is configured as Enabled, even when the system is in a power-down mode.
Primary/Secondary IDE 1/0 (Disabled)
When these items are enabled, the system will restart the power-saving timeout counters when any activity is detected on any of the drives or devices on the primary or secondary IDE channels.
FDD, COM, LPT Port (Disabled)
When this item is enabled, the system will restart the power-saving timeout counters when any activity is detected on the floppy disk drive, serial ports, or the parallel port.
Using BIOS
PCI PIRQ[A-D]# (Disabled)
When this item is enabled, any activity from one of the listed devices wakes up the system.
Power On After Power Fail (Off)
This item enables your computer to automatically restart or return to its last operating status after power returns from a power failure.
PNP/PCI Configurations
These options configure how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the the ISA and PCI buses on the motherboard use system IRQs (Interrup ReQuests) and DMAs (Direct Memory Access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup utility for the motherboard to work properly. Selecting PnP/PCI Configurations on the main program screen displays this menu:
Phoenix-AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
43
Init Display First [PCI Slot] Reset Configuration Data [Disabled]
Resources Controlled By [Auto(ESCD)]
X
IRQ Resources Press Enter
PCI/VGA Palette Snoop [Disabled] INT Pin 1 Assignment [Auto] INT Pin 2 Assignment [Auto] INT Pin 3 Assignment [Auto] INT Pin 4 Assignment [Auto] INT Pin 5 Assignment [Auto] INT Pin 6 Assignment [Auto] INT Pin 7 Assignment [Auto] INT Pin 8 Assignment [Auto]
** PCI Express relatvie items**
Maximum Payload Size [4096]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Item Help
Menu Level

Init Display First (PCI Slot)
This item allows you to choose the primary display card.
Reset Configuration Data (Disabled)
If you enable this item and restart the system, any Plug and Play configuration data stored in the BIOS Setup is cleared from memory.
Resources Controlled By Auto (Auto(ESCD))
You should leave this item at the default Auto (ESCD). Under this setting, the system dynamically allocates resources to Plug and Play devices as they are required.
If you cannot get a legacy ISA (Industry Standard Architecture) expansion card to work properly, you might be able to solve the problem by changing this item to Manual, and then opening up the IRQ Resources submenu.
IRQ Resources:In the IRQ Resources submenu, if you assign an IRQ to Legacy ISA, then that Interrupt Request Line is reserved for a legacy ISA expansion card. Press <Esc> to close the IRQ Resources submenu.
In the Memory Resources submenu, use the first item Reserved Memory
Baseto set the start address of the memory you want to reserve for the ISA
Using BIOS
44
expansion card. Use the section item Reserved Memory Length to set the
amount of reserved memory. Press <Esc> to close the Memory Resources submenu.
PCI/VGA Palette Snoop (Disabled)
This item is designed to overcome problems that can be caused by some non-standard VGA cards. This board includes a built-in VGA system that does not require palette snooping so
you must leave this item disabled.
INT Pin 1-8 Assignment (Auto)
Identifies the interrupt request (IRQ) line assigned to a device connected to the PCI inter­face of your system.
Maximum Payload Size (4096)
This item specifies the maximum TLP payload size for the PCI Express devices. The unit is byte.
PC Health Status
On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, temperatures and fan speeds.
Phoenix-AwardBIOS CMOS Setup Utility
PC Health Status
Shutdown Temperature [Disabled] CPU Warning Temperature [Disabled]
Vcore (V) 5VSB (V)
3.3V
5.0V +12V VBT Current System Temperature Current CPU Temperature Current System Fan Speed Current CPU Fan Speed
Item Help
Menu Level
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Shutdown Temperature (Disabled)
Enables you to set the maximum temperature the system can reach before powering down.
CPU Warning Temperature (Disabled)
This item allows users to set the CPU warning temperature. The default setting is Disabled. Users may change it to 60°C/140°F, 65°C/149°F, 70°C/158°F, 75°C/167°F, or 80°C/176°F
System Component Characteristics
These fields provide you with information about the systems current operating status. You cannot make changes to these fields.
Vcore
5VSB (V)
+3.3V
+5V
+12V
VBT (V)
Current System Temperature
Current CPU Temperature
Current System FAN Speed
Current CPU FAN Speed
Using BIOS
Frequency Control
This item enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.
CPU Clock Ratio [16X] Auto Detect PCI Clk [Enabled] Spread Spectrum [Enabled] CPU Clock [200MHz]
: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
CPU Clock Ratio (16X)
Enables you to set the CPU clock. The CPU clock ratio times the CPU Host/PCI Clock should equal the core speed of the installed processor.
Example: CPU Clock Ratio 16
Installed CPU Clock Speed 3200MHz
Phoenix-AwardBIOS CMOS Setup Utility Frequency Control
Item Help
Menu Level
CPU Frequency x 200
45
Auto Detect PCI Clk (Enabled)
When this item is enabled, BIOS will disable the clock signal of free DIMM and PCI slots.
Spread Spectrum (Enabled)
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.
CPU Clock (200MHz)
This item allows you to adjust the CPU clock to 200MHz. You can key-in the numbers within the range to make a precise and ideal adjustment.
Using BIOS
46
Load Fail-Safe Defaults Option
This option opens a dialog box that lets you install fail-safe defaults for all appropriate items in the Setup Utility: Press <Y> and the <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The fail-safe defaults place no great demands on the system and are generally stable. If your system is not functioning correctly, try installing the fail-safe defaults as a first step in getting your system working properly again. If you only want to install fail-safe defaults for a specific option, select and display that option, and then press <F6>.
Load Optimized Defaults Option
This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The optimized defaults place de­mands on the system that may be greater than the performance level of the components, such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults when your hardware does not support them. If you only want to install setup defaults for a specific option, select and display that option, and then press <F7>.
Users please remain the factory BIOS default setting of “Load optimized Defaults” when install Operation System onto your system.
Set Password
When this function is selected, the following message appears at the center of the screen to assist you in creating a password.
ENTER PASSWORD
Type the password, up to eight characters, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection. To disable password, just press <Enter> when you are prompted to enter password. A message will confirm the password being disabled. Once the password is disabled, the system will boot and you can enter BIOS Setup freely.
PASSWORD DISABLED
If you have selected “System” in “Security Option” of “BIOS Features Setup” menu, you will be prompted for the password every time the system reboots or any time you try to enter BIOS Setup. If you have selected “Setup” at “Security Option” from “BIOS Features Setup” menu, you will be prompted for the password only when you enter BIOS Setup.
Supervisor Password has higher priority than User Password. You can use Supervisor Password when booting the system or entering BIOS Setup to modify all settings. Also you can use User Password when booting the system or entering BIOS Setup but can not modify any setting if Supervisor Password is enabled.
Using BIOS
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <Y> to save and exit, or press <N> to return to the main menu.
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, press <Y> to discard changes and exit, or press <N> to return to the main menu.
If you have made settings that you do not want to save, use the “Exit Without Saving” item and press <Y> to discard any changes you have made.
This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.
47
Using BIOS
48
Memo
Using BIOS
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software. Before installing any software, always inspect the folder for files named README.TXT, INSTALL.TXT, or something similar. These files may con­tain important information that is not included in this manual.
Intel HD Audio Installation (optional): The Intel High Definition audio func­tionality unexpectedly quits working in Windows Server 2003 Service Pack 1 or Windows XP Professional x64 Edition. Users need to download and install the update packages from the Microsoft Download Center “before” installing HD audio driver bundled in the driver CD. Please log on to support.microsoft.com/default.aspx?scid=kb;en-us;901105#appliesto for more information.
http://
Auto-installing under Windows 2000/XP
The Auto-install CD-ROM makes it easy for you to install the drivers and software for your motherboard.
49
If the Auto-install CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.
The support software CD-ROM disc loads automatically under Windows 2000/XP. When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.
If the opening screen does not appear; double-click the file “setup.exe” in the root directory.
Using the Motherboard Software
50
Setup Tab
Setup
Browse CD
Exit The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Click the Setup button to run the software installation program. Select from the menu which software you want to install.
The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD.
Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly.
Some software is installed in separate folders for different operating systems, such as Windows 2000/XP. Always go to the correct folder for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1. Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.
The motherboard identification is located in the upper left-hand corner.
Using the Motherboard Software
2. Click Next. The following screen appears:
3. Check the box next to the items you want to install. The default options are recommended.
4. Click Next run the Installation Wizard. An item installation screen appears:
51
5. Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen instruc­tions, confirm commands and allow the computer to restart a few times to complete the installation.
Using the Motherboard Software
52
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.
Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that auto­matically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.
Utility Software Reference
All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license.
These software(s) are subject to change at anytime without prior notice. Please refer to the support CD for available software.
This concludes Chapter 4.
Using the Motherboard Software
Multi-Language Translation
Français
Caractéristiques
Peut recevoir les processeurs Intel Core™ 2 Duo/Pentium D/ Pentium 4/ Celeron D
Support un bus système (FSB) de 1066/800/533 MHz
Supporte le CPU de technologie “Hyper-Threading”
Le chipset 945G Northbridge (NB) Chipset et ICH7 Southbridge (SB) se base sur une architecture innovante et évolutive avec des performances et une fiabilité éprouvées.
945G (NB)
Prend en charge l’adressage de bus hôte 32 bits, permettant au CPU
d’accéder à l’espace de 4 Go complet d’adresse mémoire.
Interface Direct Media (DMI) point à point de 2 Go/s vers chaque
direction ICH7 (1 Go/s).
Prend en charge un PCI Express x16 pour Interface Graphique, en-
tièrement conforme à la Spécification de Base PCI Express révision
1.0a.
Prend en charge les technologies DDR2 256-Mb, 512-Mb et 1-Gb
pour x8 et x16 périphériques
Prend en charge la Configuration 3D et moteur de Rendu et moteur
de texture de haute qualité.
La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est connecté à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des processeurs ‘logiques’ dans le même processeur physique.
La carte mère utilise un type LGA775 d’Intel Core™2 Duo/Pentium D/Pentium 4/ Celeron D comportant les caractéristiques suivantes :
Processeur
Chipset
ICH7 (SB)
Fonctions de Contrôleur DMA Amélioré, de contrôleur d’interruption,
et de minuterie
Conforme aux spécifications de base PCI Express, Révision 1.0a
Conforme aux spécifications PCI 2.3.
Conforme aux spécifications ATA II Série
Contrôleur d’Hôte USB 2.0 intégré prenant en charge jusqu’à huit
ports USB 2.0
Contrôleur LAN intégré
Conforme au(x) codec(s) audio de haute définition AC’97/Intel prenant
en charge les sorties audio à 8 canaux
Contrôleur IDE intégré prenant en charge Ultra ATA100/66/33
SDRAM DDR 667/533/400 DDR2 avec architecture en double canal
Reçoit deux DIMM sans tampon
Jusqu’à 1 Go par DIMM avec une taille de mémoire maximum de 2 Go
Mémoire
Graphique
Configuration 3D et moteur de rendu
Prise en charge du rendu de zone
Moteur de texture de haute qualité
1394a FireWire (Optionnel)
Conforme au contrôleur d’hôte à puce simple pour IEEE 1394-1995 et IEEE1394a-2000
PHY à 2 ports intégré de 400 Mbits pour le Bus PCI
Alimentation 3,3V avec entrées tolérantes de 5V.
Multi-Language Translation
Français
8 canaux de format PCM 24/20/16-bits de support DAC pour solution audio 7.1
Supporte la vitesse d’échantillonnage DAC de 192K/96K/48K/44,1KHz
Support d’alimentation : Numérique : 3,3V; Analogique : 3,5V~5,25V
Conforme aux exigences audio de Microsoft WHQL/WLP 2.0
Compatible Direct Sound 3D
TM
Sortie de codeur Dolby Digital pour application électronique consomma­teur
Conforme à l’audio haute définition d’Intel, prenant en charge les DAC à 8 canaux avec rapport S/B de 95dB
Compatibilités: 192/96/48/44.1 KHz avec 24/20/16 bits
Support d’alimentation : Numérique : 3,3V; Analogique : 3,3V/5,0V
Toutes les prises analogiques sont des entrées et sorties stéréo avec réat­tribution des tâches pour plug & play analogique
Conforme aux exigences audio de Microsoft WHQL/WLP 2.0
Compatible Direct Sound 3D
TM
Sortie de codeur Dolby Digital pour application électronique consomma­teur
Conforme aux spécifications AC’97 2.3
Prend en charge le CODEC audio 6 canaux destiné aux systèmes multi­média PC
Offre trois entrées stéréo de niveau de ligne analogique avec contrôle de volume 5 bits: Ligne d’entrée, CD, AUX
Conforme aux exigences audio de Microsoft WHQL/WLP 2.0
Audio (optionnel)
La carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de transfert de 100/66 Mo/s.
La carte mère comporte les options d’extension suivantes :
Options d’extension
Un logement PCI Express x16 pour interface graphique
Un logement PCI Express x1
Deux emplacements PCI v2.3 32bits
Un en-têtes demi-hauteur IDE de 40 broches supportant deux canaux IDE
Une interface lecteur de disquettes
Quatre connecteurs SATA à 7 broches
Emetteur-récepteur 10/100/1000 intégré
Prend en charge PCI v2.3, 32 bits, 33/66-MHz
Prise en charge totale avec IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Fonctionnement en auto-négociation N-way 10/100 Mb/s
Prend en charge le fonctionnement en half/full duplex
Prise en charge de Réveil par LAN et réveil distant
LAN sur carte (optionnel)
Le contrôleur LAN interne offre les caractéristiques suivantes:
Multi-Language Translation
Français
Gestion d’alimentation
Alertes de réveil
Paramètres de CPU
Synchronisation de CPU et de mémoire
Certaines spécifications matérielles et certains éléments logiciels sont sus
-
ceptibles de modification sans préavis.
Microprogramme BIOS
La carte mère utilise Award BIOS qui permet à l’utilisateur de configurer bon nombre de fonc­tions du système, dont :
Le micro-programme peut également être utilisé pour définir les paramètres pour différentes vitesses d’horloge de processeur.
Deux ports PS/2 pour souris et clavier
Un port série
Un port parallèle
Un port VGA
Q
uatre ports USB
Un port 1394 (optionnel)
Un port LAN (optionnel)
Prises audio pour entrée microphone, entrée de ligne et Audio Haute Défi­nition 8 ch.
E/S intégrées
La carte mère comporte un ensemble complet de connecteurs et de ports E/S :
Multi-Language Translation
Deutsche
Features
Nimmt Intel Core™ 2 Duo/Pentium D/Pentium 4/ Celeron D Prozessoren auf
Unterstützt einen Systembus (FSB) mit 1066/800/533 MHz.
Unterstützt CPU mit “Hyper-Threading”-Technologie.
Die 945G Northbridge (NB) und ICH7 Southbridge (SB) Chipsätze basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung.
945G (NB)
Unterstützung einer 32-Bit Host-Bus-Adressierung, welche der CPU einen Zugriff zum kompletten Speicherplatz von 4 GB erlaubt.
2 GB/s Punkt-zu-Punkt Direct Media Interface (DMI) zu ICH7 (1 GB/s) in jede Richtung.
Unterstützung von PCI Express x16 für die Grafikschnittstelle, gemäß den PCI Express-Base-Spezifikationen Revision 1.0a.
Unterstützung von 256-Mb, 512-Mb und 1-Gb DDR2­Technologien für x8 und x16 Zubehör.
Unterstützt 3D Setup, Render-Engine und qualitativ hochwertiger
Texture-Engine
“Hyper-Threading”-Technologie läßt das Betriebssystem glauben, es sei an zwei Prozessoren angeschlossen, was zwei parallele Threads auf separaten ‘logischen’ Prozessoren im selben physischen Prozessor erlaubt.
Das Mainboard verwendet einen LGA775 Typ Intel Core™2 Duo/ Pentium D/Pentium 4/ Celeron D mit den folgenden Eigenschaften:
Prozessor
Chipsatz
ICH7 (SB)
Verbesserter DMA-Kontroller, Unterbrechungskontroller und
Zeitfunktionen.
Gemäß PCI Express-Base-Spezifikationen, Revision1.0a.
Gemäß Spezifikationen von PCI 2.3.
Gemäß Serial ATA II Spezifikationen.
Integrierter USB 2.0 Host-Kontroller, welcher bis zu acht USB
2.0 Steckvorrichtungen unterstützt.
Integrierter LAN-Kontroller.
Entspricht AC’97/Intel High Definition Audio Codec(s),
unterstützt 8-Kanal Audioausgabe
Integrierter IDE-Kontroller, welcher Ultra ATA100/66/33
unterstützt.
DDR2 667/533/400 DDR SDRAM mit Dualkanal Architektur
Es können zwei ungepufferte DIMMs aufgenommen werden.
Bis zu 1 GB pro DIMM mit maximaler Speicherkapazität von bis zu 2 GB.
Arbeitsspeicher
Grafik
3D-Setup und Render Engine
Unterstützt Zone Rendering
Qualitativ hochwertiger Texture Engine
Kompatibel mit Singlechip-Host Controller für IEEE 1394-1995 und IEEE1394a-2000
Integrierter 400 Mbit 2-Port PHY für den PCI-Bus
3.3V Stromversorgung mit 5V-toleranten Eingängen
1394a FireWire (Optional)
Multi-Language Translation
Deutsche
8-Kanal DAC Unterstützung 24/20/16-Bit PCM-Format für 7.1 Audio
Unterstützt 192K/96K/48K/44.1KHz DAC Abtastrate
Netzteilunterstützung: Digital: 3,3V; Analog: 3,5V~5,25V
Erfüllt Audioanforderungen für Microsoft WHQL/WLP 2.0
Kompatibel mit Direct Sound 3DTM
Dolby Digital Encoder-Output für Unterhaltungselektronik
Entspricht Intel High Definition Audio, unterstützt 8-Kanal DACs mit 95dB S/N Ratio
Kompatibilität: 192/96/48/44.1 KHz mit 24/20/16 Bits
Stromversorgung: Digital: 3.3V; Analog: 3.3V/5.0V
Alle analogen Buchsen mit Stereo-Input und Output-Retasking für analoges Plug & Play
Erfüllt Audioanforderungen für Microsoft WHQL/WLP 2.0
Kompatibel mit Direct Sound 3DTM
Dolby Digital Encoder-Output für Unterhaltungselektronik
Entspricht AC’97 v2.3 CODEC
Unterstützt 6-Kanal Audio CODEC, entwickelt für Multimedia PC-Syste­me
Stellt drei analoge Line-Level Stereoeingänge mit 5-bit Lautstärkeregelung zur Verfügung: Line-in, CD, AUX
Erfüllt Audioanforderungen für Microsoft WHQL/WLP 2.0
Audio (Optional)
Die Mainboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate von 100/66 MB/Sek.
Das Mainboard ist mit den folgenden Erweiterungsmöglichkeiten ausgestattet:
Erweiterungsmöglichkeiten
Ein PCI Express-Slot x16 für Grafik-Interface
Ein PCI Express x1 Slot
Zwei 32-bit PCI v2.3-Steckplätze
Einen 40-Pin IDE low profile-Stecker, die zwei IDE-Kanäle unterstützen
Ein Diskettenlaufwerkanschluss
Vier 7-Pin SATA Anschlüsse
Enthält 10/100/1000 Transceiver
Unterstützung von PCI v2.3, 32-Bit, 33/66-MHz
Volle Unterstützung mit IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• 10/100 Mb/s N-Way Auto-Negotiation-Betrieb
• Unterstützt Halb-/Vollduplex
Unterstützung für Wake-on-LAN( WOL) und Remote Wake-up
Onboard LAN (Optional)
Der Onboard-LAN-Kontroller hat folgende Eigenschaften:
Multi-Language Translation
Deutsche
Energieverwaltung
Aufweckfunktionen
CPU-Parameter
CPU- und Arbeitsspeicherfrequenz
Manche Hardwarespezifikationen und Softwareelemente können ohne Ankün­digung geändert werden.
BIOS-Firmware
Das Mainboard verwendet Award BIOS, das es Benutzern gestattet, viele Systemfunktionen inkl. der Folgenden zu konfigurieren:
Die Firmware kann auch zur Einstellung von Parametern für verschiedene Prozessortaktge
-
schwindigkeiten verwendet werden.
Zwei PS/2-Anschlüsse für Maus und Tastatur
Eine serielle Schnittstelle
Eine parallele Schnittstelle
Eine VGA Schnittstelle
Vier USB Schnittstelle
Ein 1394-Anschluss (optional)
Ein LAN-Anschluss (optional)
Audiostecker fur Mikrofoneingang, line-in und hoch definiertem Ton mit 8 Kanalen
Integrierte I/O-Schnittstellen
Das Mainboard verfügt über einen kompletten Satz von I/O-Schnittstellen und Anschlüssen:
Multi-Language Translation
Italiano
Caratteristiche
Compatibile con processori Intel Core™ 2 Duo / Pentium D/Pentium 4 / Celeron D
Supporta un bus di sistema (FSB) fino a 1066/800/533 Mhz
Supporta CPU con tecnologia “Hyper Threading”
I chipset Intel 945G Northbridge (NB) e ICH7 Southbridge (SB) sono basati su una architettura innovativa e scalabile dalle prestazioni e affidabilità garantite.
945G(NB)
Supporta un indirizzamento host bus da 32 bit, consentendo alla CPU di accedere a tutti i 4 GB della memoria di sistema.
Interfaccia DMI (Direct Media Interface) point-to-point da 2 GB/s in ciascuna direzione (1 GB/s) ICH7.
Supporta un PCI Express x16 per interfaccia grafica, completamente compatibile con le specifiche di revisione 1.0a di PCI Express Base.
Supporta tecnologie DDR2 da 256-Mb, 512-Mb e 1-Gb per dispositivi x8 e x16
Supporto di setup 3D, motore di rendering e Motore di trama ad alta qualità.
La tecnologia “Hyper-Threading” induce il sistema operativo a pensare di essere collegato a due processori, questo permette di eseguire due thread in parallelo, ambedue su processori “logicamente” separati all’interno dello stesso processore.
Processore
Chipset
ICH7 (SB)
Controller DMA migliorato, controller interrupt e funzioni di timer
Compatibile con le Specifiche di base del PCI Express, Revision1.0a
Conforme alle specifiche PCI 2.3.
Conforme alle specifiche Serial ATA II
Host Controller USB 2.0 integratoin grado di supporare sino a 8 porte USB 2.0
Controller LAN integrato
Conforme a specifiche AC’97/Intel High Definition Audio con supporto di uscite audio a 8 canali
Integrato con controller IDE supporta Ultra ATA100/66/33
Supporto di SDRAM DDR 667/533/400 DDR2 con architettura Dual Chan­nel
Alloggia 2 DIMM unbuffered
Dimensione massima della DIMM pari ad 1 GB per un ammontare massimo di 2 GB di memoria
Memoria
Grafica
Setup 3D e motore di rendering
Supporto di rendering delle aree
Motore di trama ad alta qualità
Conforme a host controller Single Chip per IEEE1394-1995 e IEEE1394a-
2000
PHY a 2 porte da 400 Mbit integrato per il bus PCI
Alimentazione a 3,3 V con ingressi dotati di tolleranza di 5 V
FireWire 1394a (Opzionale)
La scheda madre utilizza un tipo LGA775 di processore Intel Core™2 Duo / Pentium D/ Pentium 4 / Celeron D che offre le seguenti caratteristiche:
Multi-Language Translation
Italiano
8 canali per formato PCM a 24/20/16 bit con supporto DAC per soluzioni audio 7.1
Supporto di velocità di campionamento DAC a 192K/96K/48K/44,1 KHz
Supporto alimentazione: Digitale: 3,3 V; Analogico: 3,5 V ~ 5,25 V
Conforme ai requisiti per audio di WHQL e WLP 2.0 di Microsoft
Compatibile con Direct Sound 3D
TM
Uscita Dolby Digital Encorder per apparecchiature elettroniche di largo consumo
Conforme con Intel High Definition Audio e supporto di DAC a 8 canali con rapporto S/N di 95 dB
Compatibili: 192/96/48/44.1 KHz a 24/20/16 bit
Supporto alimentazione: Digitale: 3,3V; Analogico: 3,3 V / 5,0 V
Tutti i jack analogici offrono ingresso e uscita stereo con riassegnazione a plug & play analogico
Conforme ai requisiti per audio di WHQL e WLP 2.0 di Microsoft
Compatibile con Direct Sound 3D
TM
Uscita Dolby Digital Encorder per apparecchiature elettroniche di largo consumo
Conforme alle specifiche AC’97 2.3
Supporto di CODEC audio a 6 canali per sistemi PC multimediali
Tre ingressi analogici stereo lineari con controllo volume a 5 bit: Line-In, CD, AUX
Conforme ai requisiti per audio di WHQL e WLP 2.0 di Microsoft
Audio (opzionale)
La scheda madre supporta bus master UltraDMA con tasso di trasferimento di 100/66 MB/s.
La scheda madre è dotata delle seguenti opzioni di espansione
Opzioni di espansione
Uno slot PCI Express x16 per interfaccia grafica
Uno slot PCI Express x1
Due slot PCI v2.3 a 32 bit
Una connettori IDE a 40 pin che supportano due canali IDE
Un’interfaccia per unità disco floppy
Quattro connettori SATA a 7 pin.
Transceiver 10/100/1000 integrato
Supporta PCI v2.3, 32-bit, 33/66-MHz
Completamente conforme con l’IEEE 802.3,IEEE 802.3u, IEEE 802.3ab
• Operazioni di auto-negoziazione N-way 10/100 Mb/s
Supporto di funzionalità half/full duplex
Supporto di funzionalità Wake-on-LAN e riattivazione remota
LAN integrata (opzionale)
La funzionalità LAN integrata sulla scheda offre le seguenti caratteristiche:
Multi-Language Translation
Italiano
Gestione dell’alimentazione
Allarmi di attivazione
Parametri CPU
Sincronizzazione di CPU e memoria
Alcune specifiche hardware e software potrebbero essere soggette a cambiamenti senza preavviso.
Firmware BIOS
Questa scheda madre adotto un BIOS Award che permette agli utenti di configurare le caratte­ristiche principali del sistema, inclusi:
Il firmware può anche essere usato per impostare i parametri per diverse velocità di clock.
Due porte PS/2 per mouse e tastiera
Una porta seriale
Una porta parallela
Una porta VGA
Quattro porte USB
Una porta 1394 (opzionale)
Una porta LAN (opzionale)
Jack audio per microfono, line-in e 8 canali audio ad alta definizione.
I/O integrati
La scheda madre è dotata di un set completo di connettori e porte I/O:
Multi-Language Translation
Español
Características
Acomoda procesadores Intel Core™ 2 Duo/Pentium D/ Pentium 4/ Celeron D
Soporta un sistema de bus (FSB) de 1066/800/533 MHz
Soporta CPU de tecnología “Hyper-Threading”
Los chipsets Northbridge 945G (NB) y Southbridge ICH7 (SB) están basados en una arquitectura innovadora y escalable con fiabilidad y rendimiento comprobados.
945G (NB) Soporta la dirección de bus anfitrión 32-bit, que permite la CPU ac-
ceder a todos los 4 GB del espacio de dirección de memoria.
Interfaz Direct Media (DMI) punto a punto de 2 GB/s a ICH7 (1
GB/s) cada dirección.
Soporta un PCI Express x16 para la Interfaz de Gráficas,
completamente conforme a la Especificación Base PCI Express revisión 1.0a.
Soporta las tecnologías 256-Mb, 512-Mb y 1-Gb DDR2 para los
dispositivos x8 y x16.
Soporta 3D setup, motor de rendimiento y Motor de textura de alta calidad
La tecnología “Hyper-Threading” habilita el sistema operativo para que piense como si estuviera conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en procesadores “lógicos” dentro del mismo procesador físico.
La placa principal usa un tipo LGA775 de Intel Core™2 Duo/Pentium D/Pentium 4/ Celeron D que lleva las sigtes. características:
Procesador
Chipset
ICH7 (SB)
Controlador DMA reforzado, controlador de interrupción y funciones
de cornometraje.
Conforme con la Especificación Base PCI Express, Revisión1.0a.
Conforme con la espec. PCI 2.3.
Conforme con la espec. Serial ATA II
Controlador Anfitrión USB 2.0 Integrado soporta hasta ocho
puertos USB 2.0.
Controlador LAN integrado .
Conformidad con el Codec de Audio de Alta Definición Intel/AC’97
que soporta salidas de audio de 8 canales
Controlador IDE integrado soporta Ultra ATA100/66/33.
DDR SDRAM DDR2 667/533/400 con arquitectura de canal dual
Acomoda dos DIMMS sin buffer
Hasta 1 GB por DIMM con el tamaño de memoria máximo hasta 2 GB
Memoria
Gráficas
3D setup y motor de rendimiento
Soporte de Rendimiento de Zona
Motor de textura de alta calidad
1394a FireWire (opcional)
Conformidad con un controlador anfitrión de un solo chip para IEEE 1394-1995 y IEEE1394a-2000
400 Mbit 2-Port PHY integrado para el Bus PCI
Suministro de 3.3V con Entradas Tolerantes de 5V
Multi-Language Translation
Español
8 canales de formato PCM de 24/20/16-bit de soporte DAC para la
solución de audio 7.1
Soporta índice de muestreo DAC 192K/96K/48K/44.1KHz
Soporte de suministro: Digital: 3.3V; Analógico: 3.V~5.25V
Obedece a los requisitos de audio de Microsoft WHQL/WLP 2.0.
Compatible con Direct Sound 3DTM
Salida de Decondificador Dolby Digital para la aplicación de
electrónicos de consumidores
Conforme con el Audio de Alta Definición de Intel, que soporta DACs de
8 canales con proporción 95dB S/N
Compatibilidades: 192/96/48/44.1 KHz con 24/20/16 bits
Soporte de suministro: Digital: 3.3V; Analógico: 3.3V/5.0V
Todas las clavijas analógicas son de retoma de entrada y salida de estéreo
para el plug & play analógico
Obedece a los requisitos de audio de Microsoft WHQL/WLP 2.0.
Compatible con Direct Sound 3DTM
Salida de Decondificador Dolby Digital para la aplicación de
electrónicos de consumidores
Conformidad con las especificaciones AC’97 2.3
Soporta CODEC de audio de 6 canales diseñaods para los sistemas multimedia
Provee tres entradas en estéreo a nivel de línea análogicas con control de volumen de 5-bit: LIne-in, CD, AUX
Obedece a los requisitos de audio de Microsoft WHQL/WLP 2.0.
Audio (opcional)
La placa principal soporta el mastering de bus UltraDMA con índices de transferencia de 100/66 MB/s.
La placa base viene con las opciones siguientes de expansión:
Opciones de expansión
Una ranuras PCI Express x16 para la Interfaz de Gráficas
Una ranura PCI Express x1
Dos ranuras conforme con 32-bit PCI v2.3
Una cabezal de perfil bajo 40-pin IDE soporta dos canales IDE
Una interfaz para unidad de disquete
Cuatro conectores 7-pin SATA
Transceptor 10/100/1000 integrado
Soporta PCI v2.3, 32-bit, 33/66-MHz
Soporte completo con el IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• Operación de autonegociación N-way de 100/10 Mb/s
• Soporta capacidad duplex medio/completo
• Soporta la función Wake-On-LAN y despertar remoto
LAN en placa (opcional)
El controlador LAN abordo provee las sigtes. características:
Multi-Language Translation
Español
Administración de energía
Alarmas de encendido
Parámetros CPU
Temporización de memoria y CPU
Algunas especificaciones de hardware y elementos de software están sujetos a cambios sin previo aviso.
Firmware de BIOS
La placa base utiliza Award BIOS que permite a los usuarios configurar muchas funciones de sistema, incluyendo las siguientes:
El firmware también puede utilizarse para ajustar los parámetros para diversas velocidades del reloj del procesador.
Dos puertos PS/2 para ratón y de teclado
Un puerto serie
Un puerto paralelo
Un puerto VGA
Cuatro puertos USB
Un puerto 1394 (opcional)
Un puerto LAN (opcional)
Clavijas de sonido para entrada de microfono, entrada de linea y Sonido de Alta Definicion de 8 canales.
I/O integrado
La placa base tiene un conjunto completo de puertos I/O y conectores:
Multi-Language Translation
Português
Características
Acomoda processadores Intel Core™ 2 Duo/ Pentium D/ Pentium 4/ Celeron D
Suporta um bus sistema (FSB) de 1066/800/533 MHz
Suporta CPU de tecnologia “Hyper-Threading”
Os chipsets da 945G Northbridge (NB) e ICH7 Southbridge (SB) são baseados em uma arquitetura inovativa e escalável com performance e confiabilidade comprovada.
945G (NB)
Suporta um endereçamento no host bus de 32-bit, permitindo que o
CPU aceda completamente aos 4 GB de espaço de endereçamento da memória.
Interface Media Directo (DMI) ponto-para-ponto com 2 GB/seg. para ICH7 (1 GB/seg. ) cada direcção.
Suporta um PCI Express x16 Interface de Gráficos, que cumpre inteiramente com a revisão de Especificação de Base 1.0a. do PCI Express.
Suporta 256-Mb, 512-Mb e tecnologias 1-Gb DDR2 para aparelhos x8 e x16
Suporta Disposição 3D, Motor de Distribuição e motor de textura de alta qualidade
A tecnologia “Hyper-Threading” permite que o sistema operativo “pense” que está ligado a dois processadores, permitindo que sejam executados dois threads em paralelo, ambos em processadores “lógicos” separados dentro do mesmo processador físico.
Esta motherboard usa um tipo de Intel Core™2 Duo/Pentium D/Pentium 4/ Celeron D LGA775 que possui as seguintes características:
Processador
Chipset
ICH7 (SB)
Controlador DMA Melhorado, controlador de interruptor, e funções de temporizador
Cumpre com a Especificação de Base do PCI Express, Revisão
1.0a
Em conformidade com a especificação PCI 2.3
Compatível com Série ATA II
Controlador Host 2.0 USB integrado suportando até oito portas USB 2.0
Controlador LAN integrado
Compatível com a(s) Codec Áudio Alta Definição AC’97/Intel suportando saídas áudio com 8 canais
Controlador IDE integrado suporta Ultra ATA100/66/33
DDR2 667/533/400 DDR SDRAM com arquitectura bicanal
Acomoda duas DIMMs sem buffers
Até 1 GB por DIMM com tamanho de memória máxima de até 2 GB
Memória
Gráficos
Instalação 3D e dispositivo de distribuição
Suporte de Distribuição de Zona
Dispositivo de textura de elevada qualidade
1394a FireWire (opcional)
Compatível com controlador host de chip único para IEEE 1394-1995 e IEEE1394a-2000
PHY integrado de 2 portas de 400 Mbits para o PCI Bus
Fonte de alimentação de 3.3V com Entradas Tolerantes de 5V
Multi-Language Translation
Português
Formato 24/20/16-bit PCM com suporte DAC de 8 canais para solução áudio 7.1
Suporta taxa de amostragem DAC 192K/96K/48K/44.1KHz DAC
Suporte de potência: Digital: 3.3V; Analógica: 3.5V~ 5.25V
Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft.
Compatível com Direct Sound 3D
TM
Saída Descodificador Digital Dolby para aplicação electrónica de consumo
Compatível com Alta Definição Áudio da Intel, suportando DACs com 8 canais com rácio 95dB S/N
Compatibilidades: 192/96/48/44.1 KHz com 24/20/16 bits
Suporte de alimentação: Digital: 3.3V; Analógico: 3.3V/5.0V
Todas as fichas analógicas são entradas estéreo e redistribuição de saídas para ligar & reproduzir analógico
Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft.
Compatível com Direct Sound 3D
TM
Saída Descodificador Digital Dolby para aplicação electrónica de consumo
Cumpre com as especificações AC’97 2.3
Suporta CODEC áudio com 6 canais concebido para sistemas multimédia para PC
Fornece três entradas estéreo nível de linha analógicas com controlo de volume de 5 bits: LIne-in, CD, AUX
Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft.
Áudio (opcional)
A motherboard suporta um domínio bus UltraDMA bus com taxas de Transferência de 100/66 MB/s.
A motherboard é fornecida com as seguintes opções de expansão:
Opções de Expansão
Uma ranhura x 16 PCI Express para Interface de Gráficos
Uma ranhura x1 PCI Express
Duas ranhuras compatíveis com PCI v2.3 de 32 bits
Uma cabeçalhos de baixo perfil IDE 40 pinos, que suportam dois dispositivos IDE
Uma interface para unidade de disquete
Quatro conectores SATA de 7 pinos
Transreceptor integrado 10/100/1000
Suporta PCI v2.3, 32-bit, 33/66-MHz
Suporta inteiramente com IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• Funcionamento de auto-negociação 10/100 Mb/s N-way
Suporta capacidade de duplex pela metade/ou na totalidade
Suporte Wake-on-LAN ( WOL) e wake-up remoto
Onboard LAN (opcional)
O controlador LAN onboard contém as seguintes características:
Multi-Language Translation
Português
Gerenciamento de energia
Alarmes de reativação
Parâmetros da CPU
Sincronização da CPU e memória
Alguns itens de software e especificação de hardware estão sujeitos a alterações sem prévio aviso.
Firmware do BIOS
A motherboard usa o Award BIOS que permite aos usuários configurar vários recusos do sistema, como:
O firmware também pode ser usado para definir os parâmetros de diferentes velocidades de clock do processador.
Duas portas PS/2 para o rato e o teclado
Uma porta de série
Uma porta paralela
Uma porta VGA
Quatro portas USB
Uma porta 1394 (opcional)
Uma porta LAN (opcional)
Fichas áudio para microfone, alinhadas e com Áudio de Elevada Definição 8-ch
I/O Integrado
A motherboard possui um conjunto completo de portas I/O e conectores:
Multi-Language Translation
日本語
機能
Intel Core2 Duo/Pentium D/Pentium 4/ Celeron D プロセッサの搭載が
可能
1066/800/533MHzのシステムバス(FSB)をサポート
“ハイパースレッド技術対応のCPUを取り付け可能
945G Northbridge (NB)とICH7 Southbridge (SB)チップセットは、実証された信頼性 と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。
945G(NB)
32ビットホストバスアドレシング機能対応、これでCPUが4 GBのメ
モリアドレス空間すべてをアクセス可能
2 GB/秒 point-to-point Direct Media Interface (DMI) で
ICH7とのデータやり取りを1 GB/秒の転送率で実現
グラフィックインターフェース用PCI Express x16 スロットを提
供、これでPCI Express Base Specification revision 1.0aに完 全対応
8倍速または16倍速のデバイスの256-Mbや512-Mb、1-Gb の
DDR2技術に対応
3D Setup機能、Renderエンジン、及び高品質のテクスチャエンジ
ンをサポート
ハイパースレッド(HT) 技術というのは、オペレーションシステムに2つのプロセッサが存在すると認識 させることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ、平行利用を可能とする技 術です。
本マザーボードは LGA775タイプのIntel Core2 Duo/Pentium D/Pentium 4/ Celeron D
をサポートするもので、下記の特徴を持っています:
プロセッサ
チップセット
ICH7(SB)
強化型DMAコントローラと、割り込みコントローラ、タイマー機能を
提供
PCI Express Base Specification 1.0a版に完全対応
PCI 2.3仕様に準拠
シリアルATA II 仕様に準拠
統合型USB 2.0ホストコントローラで、最大8つまでのUSB 2.0 ポ
ートを対応可能
統合型LANコントローラ
AC’97/Intel High Definition Audio Codec(s)規格に対応し、
8チャネルのオーディオ出力可能
統合型IDEコントローラで、Ultra ATA100/66/33サポート可能
DDR2 667/533/400 DDR SDRAM に対応し、デュアルチャネル 構成を実現
2つの非バッファーDIMMを搭載
各DIMMスロットに1 GBまで装着可能で、合計2GBまでをサポート
メモリ
グラフィック
3Dセットアップ&レンダーエンジンを導入
ゾーンレンダリング機能をサポート
高品質テクスチャエンジンを導入
1394a Fire Wire(オプション)
“IEEE 1394-1995 and IEEE1394a-2000”基準のシングル・チップ・ホスト・
コントローラに対応
PCI バスの400 Mbit 2-Port PHY を内蔵
3.3Vの電源サプライを採用し、許容入力5V
Multi-Language Translation
日本語
8チャネルのDACで、 7.1オーディオソリューションの24/20/16-bit
PCM形式をサポート
192K/96K/48K/44.1KHz DAC サンプリング率をサポート
電源サポート: 3.3V(デジタル方式の場合)、3.5V~5.25V(アナログ方式
の場合)
Microsoft WHQL/WLP 2.0 オーディオ規格に準拠
Direct Sound 3DTM に対応
電化製品向けのDolby Digital Encorder出力機能を搭載
Intel High Definition Audio規格に準拠することで、95dB S/N率の8チャ
ネル DACをサポート
互換性: 24/20/16 ビットでの192/96/48/44.1 KHz
電源サポート:デジタルの場合は 3.3V、アナログの場合は3.3V/5.0V
すべてのアナログ端子は、ステレオ入出力re-tasking機能によるアナログ
plug & playが可能
Microsoft WHQL/WLP 2.0 オーディオ規格に準拠
Direct Sound 3DTM に対応
電化製品向けのDolby Digital Encorder出力機能を搭載
AC’97 2.3 規格に準拠
PCマルチメディアシステムの6チャネルオーディオCODECをサポート
5ビット音声コントロール可能のアナログラインレベルのステレオ入力が
3つ:ラインイン、CD、およびAUX
Microsoft WHQL/WLP 2.0 オーディオ規格に準拠
オーディオ (オプション)
このマザーボードは、100/66 MB/秒の転送速度でのUltra DMAバスマスタリングをサ ポートします。
本マザーボードでは、次の拡張機能が利用できます。
拡張オプション
グラフィックインターフェース用のPCI Express x16 スロットが1つ
PCI Express x1 スロットが1つ
32ビットPCI v2.3 互換性スロットが2つ
40ピンIDEロープロフィルヘッダー(2つのIDEチャネルをサポート)が1つ
フロッピーディスク ドライブ インターフェイス が1つ
7ピンSATAコネクタ が4つ
10/100/1000 トランシーバーを搭載済み
PCI v2.3, 32-bit, 33/66-MHzへの対応
IEEE 802.3、IEEE 802.3u、IEEE 802.3abへの全面対応
10/100 Mb/s Nウェイ自動折衝動作
半/全二重の機能をサポート
Wake-on-LAN と遠隔 wake-upとの機能をサポート
オンボードLAN (オプション)
オンボードLANコントローラで次の機能を実現:
Multi-Language Translation
日本語
電源管理
ウェークアップアラーム
CPUパラメータ
CPUおよびメモリのタイミング
一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更することが あります。
BIOSファームウェア
本マザーボードはAward BIOSを採用し、次の機能を含めた多様なシステム構成を行え ます。
さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更す ることもできます。
マウスとキーボード用のPS/2ポート が2つ
シリアルポート が1つ
パラレルポート が1つ
VGAポート が1つ
USBポート が4つ
1394ポート が1つ(オプション)
LANポート が1つ(オプション)
さらに、マイ クロホン入力と 、ラ イン入力と、8 チャネルHig h Defin ition
Audio出力とを搭載。
統合I/O
マザーボードには、次のI/Oポートやコネクタを揃えています。
Multi-Language Translation
한국인
특징
인텔 코어™2 듀오/팬티엄 D/팬티엄 4/ 셀러론 D 프로세서 탑재
1066/800/533 MHz시스템 버스(FSB) 지원
”Hyper-Threading”기술 CPU 지원
945G Northbridge (NB) 와 ICH7 Southbridge (SB) 칩셋은혁 신적이고 범위성을 지 닌 아키텍쳐를 바탕으로 인정된 신뢰성과 성능을 지닌다.
945G (NB)
32 비트 호스트 버스 어드레싱 지원으로, CPU 가 총 4 GB 메
모리 어드레스 공간에 액세스할 수 있다.
ICH7 (1 GB/s).에 각 방향으로 2 GB/s point-to-point Direct
Media Interface (DMI)
그래픽 인터페이스를 위해 1 개의 PCI Express x16 지원,
PCI Express Base 1.0a 사양 완전 부합.
x8 및 x16 장치를 위해 256-Mb, 512-Mb, 1-Gb DDR2 기술
지원.
고품질의 텍스쳐 엔진과 함께 3D 설정, 랜더 엔진
”Hyper-Threading”기술은 운영체제를 두 개의 프로세서에 연결한 것처럼 두개의 트래드를 패러럴로 실행하여 같은 물리적 프로세서 안에서 각기 다른
논리적 프로세
서를 실행할 수 있게 한다.
본 마더보드는 인텔 코어
2 듀오/팬티엄 D/팬티엄 4/ 셀러론 D 의 LGA775 타입을 사용
하였으며 다음과 같은 특성을 지닌다.
프로세서
칩셋
ICH7 (SB)
보강 DMA 컨트롤러, 인터럽트 컨트롤러, 및 타이머 기능
PCI Express Base 1.0a 사양 부합
PCI 2.3 사양 호환.
시리얼 ATA II 사양 호환
통합 LAN 컨트롤러
AC97 부합/8 채널 오디오 출력을 지원하는 인텔 HD 오디오
코덱
오디오 출력에 8 개 채널을 지원하는 Azalia 사양 부합
통합 IDE 컨트롤러로 Ultra ATA100/66/33 지원
듀얼 채널 아키텍처를 지닌 DDR2 667/533/400 DDR SDRAM
2 개의 unbuffered DIMM 사용
DIMM 당 최대 1 GB, 최대 메모리 2 GB
메모리
그래픽
3D 설정 및 랜더 엔진
Zone 랜더링 지원
고품질 텍스처 엔진
1394a 파이어 와이어(선택 사항)
IEEE 1394-1995 및 IEEE1394a-2000 용 싱글 칩 호스트 컨트롤러 호환
PCI 버스 용 통합 400 Mbit 2 포트 PHY
3.3V 전원 공급 장치 (5V 허용오차)
Multi-Language Translation
한국인
8 채널 DAC, 7.1 오디오 솔루션을 위해 24/20/16 비트 PCM 포맷 지원
192K/96K/48K/44.1KHz DAC 샘플 속도 지원
전원 지원: 디지털: 3.3V; 아날로그: 3.5V~5.25V
마이크로소프트 WHQL/WLP 2.0 오디오 요구에 부합
Direct Sound 3DTM 호환
소비자 전기 어플리케이션을 위한 돌비 디지털 인코더 출력
95dB S/N 비율로 8 채널 DAC를 지원하는 HD 오디오 부합
호환성: 24/20/16 비트의 192/96/48/44.1 KHz
전원 지원: 디지털: 3.3V; 아날로그: 3.3V/5.0V
모든 아날로그 잭은 스테레오 입력 및 출력, 아날로그 플러그 앤 플레이를
위한 re-tasking.
마이크로소프트 WHQL/WLP 2.0 오디오 요구에 부합
Direct Sound 3DTM 호환
소비자 전기 어플리케이션을 위한 돌비 디지털 인코더 출력
AC97 2.3 사양 부합
PC 멀티미디어 시스템을 위해 디자인 된 6 채널 오디오 코덱 지원
5 비트 볼륨 컨트롤의 아날로그 라인 레벨 스테레오 입력 3개 : Line-in,
CD, AUX
마이크로소프트 WHQL/WLP 2.0 오디오 요구에 부합
오디오 (선택 사항)
마더보드는 전송 속도 100/66 MB/s의 UltraDMA 버스 마스터링을 지원한다.
이 메인보드는 다음과 같은 확장 옵션이 있다
확장 옵션
그래픽 인터페이스 용 PCI Express 16 개 x 슬롯 1 개
PCI Express 1 개 x 슬롯 1 개
32 비트 PCI v2.3 호환 슬롯 2 개
2 개의 IDE 채널을 지원하는 40핀 IDE 로우 프로파일 해더 1 개
플로피 디스크 드라이브 인터페이스 1 개
7 핀 SATA 커넥터 4개
통합 10/100/1000 트랜시버
PCI v2.3, 32-bit, 33/66-MHz 지원
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab 전적으로 지원
10/100 Mb/s N-way 자동 감지
Half/full 듀플렉스 지원.
Wake-on-LAN 및 원격 wake-up 지원
보드 내장 LAN (선택 사항)
보드 내장 LAN 컨트롤러는 다음과 같은 특징을 제공한다:
Multi-Language Translation
한국인
전원 관리
Wake-up 알람
CPU 파라미터
CPU 및 메모리 타이밍
하드웨어 사양 및 소프트웨어 아이템은 사전 통보없이 변경될 수 있 습니다
BIOS 펌웨어
본 메인보드는 Award BIOS 를 사용하여 사용자는 다음과 같은 시스템 기능을 구성 할 수 있다
펌웨어는 다른 프로세서의 클럭 속도를 설정하는 데도 사용될 수 있다
마우스와 키보드용 PS/2 포트 2 개
시리얼 포트1개
패러럴 포트 1 개
VGA 포트 1 개
USB 포트 4 개
1394 포트 1 개 (선택 사항)
LAN 포트 1 개 (선택 사항)
마이크 폰 입력, 라인 입력 및 8 채널 고 재생음 오디오를 위한 오디오 잭
통합 I/O
이 메인보드에는 풀 세트의 I/O 포트와 커넥터가 있다
Multi-Language Translation
繁體中文
功能
支援 Intel Core 2 Duo/ Pentium D/Pentium 4/ Celeron D 處理器 ‧ 支援高達 1066/800/533MHz之系統匯流排(FSB) ‧ 支援使用超執行緒(Hyper-Threading)技術之CPU
945G北橋(NB)及ICH7南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構,具備 優良的可靠性及性能。
945G (NB)
支援32位元主控匯流排定址,藉此CPU 可存取整個4 GB的記
憶位址空間
提供對ICH7的2 GB/秒點對點Direct Media Interface (DMI),雙
向1 GB/秒
具有一個繪圖卡用之PCI Express x16 介面,完全符合PCI
Express Base Specification 1.0a版 ‧ 支援8倍速及16倍速之256-Mb、512-Mb、及1-Gb DDR2技術 ‧ 支援高品質3D算圖引擎及高品質紋理引擎
利用“超執行緒(HT)"技術,可使作業系統在相當於裝上了兩具處理器的狀態下運 作:利用一個"實體"處理器模擬出兩個獨立的"邏輯"處理器,同時執行兩個工作 緒。
本主機板可安裝一個 LGA775型式之Intel Core2 Duo/Pentium D/Pentium 4/ Celeron D , 並具有如下特色:
處理器
晶片組
ICH7 (SB)
增強型DMA控制器、中斷控制器、及計時功能 ‧ 符合PCI Express Base Specification 1.0a版 ‧ 符合PCI 2.3規格 ‧ 符合SATA II 規格 ‧ 內建式USB 2.0主控,可支援8個USB 2.0埠 ‧ 內建式區域網路控制器 ‧ 相容於支援8聲道音訊輸出功能之高傳真音效編碼解碼器
(High Definition Audio Codec)規格 ‧ 整合式IDE控制器,支援Ultra ATA100/66/33
支援具有雙通道架構之DDR2 667/533/400 DDR SDRAM ‧ 具有2個非緩衝式DIMM ‧ 各DIMM可安裝1GB記憶體,共可支援高達2GB的記憶體容量
記憶體
‧ 3D Setup 及 Render引擎 ‧ 支援區域繪圖成形(Zone Rendering)功能 ‧ 高品質紋理引擎
繪圖卡
1394a Fire Wire (選購)
相容於"IEEE 1394-1995 and IEEE1394a-2000"規格之單晶主控制器 ‧ 內建PCI匯流排之 400 Mbit 雙埠 PHY ‧ 採3.3V 電源供應,5V之容限電壓輸入
Multi-Language Translation
繁體中文
配備8通道之DAC,可支援 7.1音訊解決方案之24/20/16-bit PCM 格式 ‧ 支援 192K/96K/48K/44.1KHz DAC 取樣率 ‧ 電源支援: 3.3V(數位)、3.5V~5.25V(類比) ‧ 符合Microsoft WHQL/WLP 2.0 音訊規格 ‧ Direct Sound 3DTM 相容 ‧ 支援家用電子產品之杜比數位編碼輸出功能
相容於Intel High Definition Audio規格,可支援95dB S/N 比的 8聲道DAC ‧ 相容性:24/20/16位元下之192/96/48/44.1 KHz; ‧ 電源支援:3.3V(數位時),3.3V/5.0V(類比時) ‧ 所有類比插頭均具類比隨插即用的立體環場音訊輸入及輸出的重組態(re-
tasking)功能 ‧ 符合Microsoft WHQL/WLP 2.0 音訊規格 ‧ Direct Sound 3DTM 相容 ‧ 支援家用電子產品之杜比數位編碼輸出功能
相容於AC´97 2.3 規格 ‧ 支援為個人電腦多媒體系統設計的6聲道音訊CODEC功能 ‧ 提供具有5位元音量控制功能的3種類比線級立體音效輸入:Lin-in、CD、
及AUX 符合Microsoft WHQL/WLP 2.0 音訊規格
音效(選購)
本主機板支援傳輸率100/66 MB/秒下的Ultra DMA 匯流排主控功能。
本主機板包括下列擴充選項:
擴充選項
1個繪圖介面用之PCI Express x16插槽 ‧ 1個PCI Express x1 插槽 ‧ 2個32位元PCIv2.3插槽 ‧ 1個40針IDE接頭(支援2個IDE裝置) ‧ 1個軟碟機介面 ‧ 4個7針SATA插頭
整合有10/100/1000 收發器 ‧ 支援PCI v2.3, 32位元, 33/66MHz ‧ 支援IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
‧ 10/100 Mb/s N路自動協商動作 ‧ 支援半/全雙工功能 ‧ 支援區域網路喚醒(Wake-On-LAN)及遠端喚醒功能
內建區域網路 (選購)
內建區域網路控制器具有如下功能:
Multi-Language Translation
繁體中文
電源管理 ‧ 喚醒警鈴 ‧ CPU參數 ‧ CPU及記憶體的時脈定時
部份硬體規格和軟體內容可能會在未經通知的情況下更動,敬請見諒。
BIOS 韌體
本主機板使用Award BIOS,使用者可以組態設定許多系統功能,包括如下:
此外,也可藉由參數的設定,調整處理器的時脈速度。
2 個 PS/2 埠,供滑鼠與鍵盤使用 ‧ 1 個串列埠 ‧ 1 個平行埠 ‧ 1 個VGA埠 ‧ 4 個USB埠 ‧ 1 個1394埠
(選購)
1 個區域網路埠(選購) 具有麥克風輸入端子、Line級輸入端子、及 8聲道高傳真音效(High Definition
Audio)輸出端子
整合 I/O
主機板具有齊全的 I/O 連接埠及連接頭:
Multi-Language Translation
简体中文
功能
支持 Intel Core2 Duo/Pentium D/Pentium 4/ Celeron D处理器
支持 1066/800/533 MHz 系统总线 (FSB)
支持“多线程”技术 CPU
945G北桥 (NB) 和 ICH7 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构,能提供 已经证明的可靠性和高性能。
945G (NB)
支持 32 位主机总线寻址,允许 CPU 访问 4 GB 的完整内
存地址空间。
每个方向 2 GB/s 点到点直接媒体接口 (DMI) 到 ICH7 (1
GB/s)。
支持 1 个 PCI Express x16 用于图形接口,完全符合 PCI
Express Base 规格 1.0a。
支持用于 x8 和 x16 设备的 256-Mb、512-Mb 和 1-Gb
DDR2 技术
支持高性能 3D 设置, 着色引擎和高性能纹理引擎
“多线程”技术可以让操作系统认为自己连接了两个处理器,允许两个线程并行运行, 每个线程位于同一处理器中的单独“逻辑”处理器中。
此主板使用 LGA775 型 Intel Core2 Duo/Pentium D/Pentium 4/ Celeron D 处理器, 具有以下特点:
处理器
芯片组
ICH7 (SB)
增强 DMA 控制器、中断控制器和定时器功能
符合 PCI Express Base 规格 1.0a
符合 PCI 2.3 规格
符合串行 ATA II 规格
集成 USB 2.0 主控器,最多支持 8 个 USB 2.0 端口
集成 LAN 控制器
符合支持 8 路音频输出的 AC97/Intel 高精度音频编解码
器规格
集成 IDE 控制器,支持 Ultra ATA100/66/33
DDR2 667/533/400 DDR SDRAM,双通道架构
支持 2 个非缓冲 DIMM
每个插槽支持 1 GB,总共最大可支持 2 GB
内存
图形
3D 设置和着色引擎
支持区域着色
高性能纹理引擎
1394a 火线(可选)
符合用于 IEEE1394-1995 和 IEEE1394a-2000 的单芯片 PCI 主机控制器标准
集成用于 PCI 总线的 400 Mbit 2 端口 PHY
3.3V 电源,带 5V 容错输入
Multi-Language Translation
简体中文
8 通道 DAC,支持 24/20/16 位 PCM 格式用于 7.1 音频解决方案
支持 192K/96K/48K/44.1KHz DAC 采样速率
电源支持: 数字亮:3.3V;模拟量:3.5V~5.25V
符合 Microsoft WHQL/WLP 2.0 音频要求
符合 Direct Sound 3DTM 规格
用于消费类电子应用的杜比数字编码器
符合高精度音频规格,支持 8 通道 DAC,95dB 信噪比
兼容性:192/96/48/44.1 KHz,24/20/16 位
支持 8 个智能插孔 I/O 端口
电源支持:数字:3.3V;模拟:3.3V/5.0V
所有模拟插孔为立体声输入和输出并重新指定为模拟即插即用
符合 Microsoft WHQL/WLP 2.0 音频要求
符合 Direct Sound 3DTM 规格
用于消费类电子应用的杜比数字编码器
兼容 AC97 v2.3 规格
支持为PC多媒体系统设计的 6 声道音频编解码器
提供 3 路带 5 位音量控制的模拟线路电平立体声输入:线入、CD 和
AUX
符合 Microsoft WHQL/WLP 2.0 音频要求
音频
此主板支持 Ultra DMA 总线控制,传输速率可达 100/66 MB/sec。
此主板提供如下扩展选项:
扩展选项
1 个用于图形接口的 PCI Express x16 插槽
1 个 PCI Express x1 插槽
2 个 32 位 PCI 扩展插槽
1 个 40-pin IDE 紧凑型接口,支持 2 个 IDE 通道
1 个软驱接口
4 个 7-pin SATA 接口
集成 10/100/1000 收发器
支持 PCI v2.3,32-位,33/66-MHz
完全支持 IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
10/100 Mb/s N 路自侦测运行
支持半双工/全双工工作
支持 LAN 唤醒 (WOL) 功能和远程唤醒功能
Onboard LAN (可选)
板上集成的 LAN 控制器提供以下功能:
Multi-Language Translation
简体中文
电源管理
唤醒报警
CPU 参数
CPU 和记忆定时
某些硬件规格和软件项目若有更改恕不另行通知。
BIOS
此主板使用 Award BIOS,可以让用户自己配置以下系统功能:
还可用于设置不同处理器时钟速度的参数。
2 个用于连接鼠标和键盘的 PS/2 端口
1 个串口
1 个并口
1 个 VGA 端口
4 个 USB 端口
1 个 1394 端口(可选)
1 个 LAN 端口(可选)
用于麦克风、线入和 8 声道高清晰度音频的音频插孔
集成 I/O
此主板具有完整的 I/O 端口和插孔:
Multi-Language Translation
Русский
Чипсеты 945G «Северный мост» (Northbridge, NB) и ICH7 «Южный мост» (Southbridge, SB) построены с использованием инновационной масштабируемой архитектуры, обеспечивающей высокую надежность и производительность.
945G (NB)
Поддерживает 32-битную адресацию хоста, обеспечивая для
CPU адресацию памяти объемом 4ГБ .
Интерфейс передачи данных Direct Media point-to-point со
скоростью 2 ГБ/с (DMI) к ICH7 (1 ГБ/с) в каждом направлении.
Имеет один разъем для подключения карты графики PCI
Express x16; обеспечивает полную соместимость с PCI Express Base, rev. 1.0a.
Поддерживает технологии 256-Мб, 512-Мб и 1-Гб DDR2 для
устройств
x8 и x16
Процессор трехмерной графики (3D setup, render)и Процессор
высококачественных текстур
Память
DDR2 667/533/400 DDR SDRAM с двухканальной архитектурой
Обслуживает 2 модуля небуферизованной памяти DIMM
Обслуживает до 1 ГБ на модуль DIMM (максимально до 2 ГБ памяти)
Чипсет
ICH7 (SB)
Расширенные функции контроллера DMA, контроллера прерываний
, внутреннего таймера
Совместимость с PCI Express Base, Rev. 1.0a
Совместимость с PCI 2.3
Совместимость с Serial ATA II
Встроенный контроллер хоста USB 2.0 с поддержкой до
восьми портов
USB 2.0
Встроенный контроллер LAN
Совместимость с аудио КОДЕК AC’97/Intel High Definition и
поддержка 8-канального аудио-выхода
Встроенный контроллер IDE с поддержкой Ultra ATA100/66/33
Характеристики
Процессор
Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине имеется два процессора; это позволяет параллельно обслуживать два процесса, причем каждый из процессов обслуживается отдельным «логическим» процессором в пределах одного физического процессора.
Материнская плата построена для процессоров типа LGA775 Intel Core™2 Duo/Pentium D/ Pentium 4/Celeron D и обладает следующими свойствами:
Размещает процессоры Intel Core™ 2 Duo/Pentium D/Pentium 4/Celeron D
Поддерживает системные шины (FSB) с частотой 1066/800/533MHz
Поддерживает технологию CPU “Hyper-Threading”
Графика
Процессор трехмерной графики (3D setup and render)
Поддержка технологии Zone Rendering
Процессор высококачественных текстур
Multi-Language Translation
Русский
Аудио (опционально)
Поддерживает 8-канальный DAC в 24/20/16-битном PCM формате для аудио вер. 7.1
Поддерживает частоту сэмплирования DAC 192K/96K/48K/44.1 КГц
Электропитание: цифровой режим: 3.3V; анал оговый режим:
3.5V~5.25V
Соответствует нормам звуковых карт Microsoft WHQL/WLP 2.0
Совместимость с Direct Sound 3D
TM
Декодер цифрового выхода Dolby соместим с домашней электроникой
Совместимость с аудио-технологией Intel High Definition, поддержка 8-канального DAC с соотношением сигнал/шум 95дБ
Совместимость с 192/96/48/44.1 KГц для 24/20/16 бит
Электропитание: цифровое: 3.3V; аналоговое: 3.3V/5.0V
Все аналоговые гнезда аудио имеют стереовход и выходa и пригодны для аналогового plug & play
Соответствует нормам звуковых карт Microsoft WHQL/WLP 2.0
Совместимость с Direct Sound 3D
TM
Декодер цифрового выхода Dolby соместим с домашней электроникой
Совместимость со спецификацией AC’97 2.3
Поддерживает 6-канальный аудио CODEC для мультимедиальных компьютерных систем
Обеспечивает три аналоговых стереовхода с 5-битной регуляцией громкости: Line-in, CD, AUX
Соответствует нормам звуковых карт Microsoft WHQL/WLP 2.0
Встроенный сетевой адаптер LAN (опционально)
Интегрированный трансивер 10/100/1000
Поддеркжа PCI v2.3, 32-бит, 33/66-MГц
Полная совместимость с технологией IEEE 802.3, IEEE 802.3u, IEEE
802.3ab
Режим автовыбора 10/100 Mb/s N-way
Поддержка режимов Half и Full Duplex
Функция Wake-on-LAN и удаленного пробуждения
Встроенный сетевой адаптер LAN обладает следующими характеристиками:
1394a FireWire (опционально)
Совместимость с одночипным контроллером хоста для IEEE 1394-1995 и IEEE1394a-2000
Встроенный 400 Mбит 2-портовый PHY для шины PCI
Питание 3.3 В при допустимости 5В на входе
Multi-Language Translation
Русский
Интегрированный вход/выход
Плата снабжена полным набором портов входа/выхода и разъемов:
Два порта PS/2 для подключения мыши и клавиатуры
Один серийный порт
Один параллельный порт
Один VGA порт
Четыре порта USB
Один порт 1394 (опционально)
Один порт LAN (опционально)
Гнездо для подключения микрофона, гнездо аудио-входа и 8­канального аудиовыхода
BIOS
Плата работает под Award BIOS, который позволяет пользователю конфигурировать различные характеристики системы:
Управление питанием
Сигналы пробуждения системы
Параметры CPU
Время доступа для CPU и памяти
BIOS допускает также установку параметров для различных частот процессора.
Некоторые параметры платы и характеристики ее программного обеспечения могут быть изменены без предварительного уведомления.
Плата поддерживает технологию захвата управления шиной UltraDMA bus mastering со скоростью передачи данных 100/66 МБ/сек.
Существуют следуюшие опции расширения данной материнской платы:
Один слота PCI Express x16 для графического интерфейса
Один слот PCI Express x1
Два
32-битных слота PCI v2.3
Один низкопрофильный 40-штырьковый слот IDE, обеспечивающий поддержку двух устройств IDE
Один разъем для накопителя на гибких дисках
Четыре 7-штырьковых разъема SATA
Возможности расширения
Multi-Language Translation
Polski
Mostek północny (NB) 945G i mostek południowy (SB) ICH7 chipsetu oparty jest na nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.
945G (NB)
Obsługuje 32-bitowe adresowanie hosta pozwalając procesorowi zaadresować 4 GB pamięci
Interfejs bezpośredniego połączenia (DMI) typu point-to-point 2 GB/s do ICH7 (1 GB/s) w każdym kierunku
Obsługuje jedno złącze grafiki PCI Express x16; całkowicie zgodne z technologią PCI Express Base, w wersji 1.0a.
Obsługuje pamięci 256-Mb, 512-Mb i 1-Gb w technologii DDR2 w urządzeniach x8 i x16
Obsługuje procesor 3D setup, render i procesor tekstur wysokiej jakości
Pamięć
DDR2 667/533/400 DDR SDRAM z architekturą dwukanałową
Zaopatrzony w dwa gniazda niebuforowanej pamięci typu DIMM
Obsługuje pamięć DIMM do pojemności 1 GB każda; maksymalna możliwa pojemność pamięci do 2 GB
Chipset
ICH7 (SB)
Rozszerzony kontroler DMA, kontroler przerywań i funkcje zegara
Zgodny z technologią PCI Express Base, Rev. 1.0a
Zgodny z PCI w wersji 2.3
Zgodny ze standardem Serial ATA II
Wbudowany kontroler hosta USB 2.0 obsługuje do ośmiu portów USB
Wbudowany kontroler LAN
Zgodny z protokołem AC’97/Intel High Definition Audio Codec(s), obsługuje 8 kanałowe wyjście audio
Wbudowany kontroler IDE obsługujący Ultra ATA100/66/33
Cechy
Procesor
Płyta główna posiada podstawkę typu LGA775, która jest przystosowana do obsługi procesorów Intel Core™2 Duo/Pentium D/Pentium 4/ Celeron D i posiada następujące właściwości:
Dostosowana do procesorów: Intel Core™ 2 Duo/Pentium D/ Pentium 4/ Celeron D
Obsługuje szynę systemowa (FSB) 1066/800/533MHz
Zabezpiecza technologię CPU “Hyper-Threading”
Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden z dwuch "logicznych" procesorów w ramach jednego fizycznego procesora
Grafika
Procesor 3D setup i render
Obsługuje technologię Zone Rendering
Procesor tekstur wysokiej jakości
1394a FireWire (opcjonalnie)
Zgodny z kontrolerem pojedynczego chipa IEEE 1394-1995 i IEEE1394a­2000
Dwa 400 MB złącza PHY zintegrowane z szyną PCI
Zasilacz -3,3 V z tolerancją wejścia 5 V
Multi-Language Translation
Polski
Płyta główna obsługuje szynę UltraDMA z szybkością transferu 100/66 MB/s.
Płyta głwna wyposażona jest w następujące gniazda:
Jedno gniazdo PCI Express x 16 dla kart graficznych
Jedno gniazdo PCI Express x1
Dwa 32-bitowych gniazda zgodnych z PCI w wersji 2.3
Jedno 40-nóżkowe złącze niskoprofilowe obsługujące dwa urządzenia IDE
Jedno złącze obsługujące stacje dyskietek
Cztery 7-nóżkowe złącza SATA
Możliwości rozbudowy
Audio (opcjonalnie)
Obsługuje 8 kanałów DAC w formacie 24/20/16-bit PCM w standardzie audio 7.1
Obsługuje częstotliwości próbkowania 192K/96K/48K/44.1KHz DAC
Zasilacz obsługuje odbiorniki 3.3V cyfrowe i 3.5V~5.25V analogowe
Spełnia wymagania audio według standardu Microsoft WHQL/WLP w wersji 2.0
Zgodny z Direct Sound 3DTM
Dekoder cyfrowego wyjścia Dolby pozwalający na współpracę z domową elektroniką
Zgodny z protokołem Intel High Definition Audio, obsługuje 8 kanałowe DAC ze stosunkiem sygnał/szum równym 95dB
Zgodność: 192/96/48/44.1 KHz z 24/20/16 bitami
Zapewnia zasilanie: 3,3 V cyfrowe; 3.3 V/5.0 V analogowe
Wszystkie analogowe gniazda wejściowe i wyjściowe typu jack są stereofoniczne i przystosowane do analogowego plug & play
Spełnia wymagania audio według standardu Microsoft WHQL/WLP w wersji 2.0
Zgodny z Direct Sound 3DTM
Dekoder cyfrowego wyjścia Dolby pozwalający na współpracę z domową elektroniką
Zgodne ze specyfikacją AC’97 w wersji 2.3
Obsługuje 6 kanałów audio CODEC dla komputerowych systemów multimedialnych
Zapewnia trzy wejściowe, analogowe linie stereo z 5 bitową regulacją głośności: Line-in, CD, AUX
Spełnia wymagania audio według standardu Microsoft WHQL/WLP w wersji 2.0
Zintegrowana obsługa sieci LAN (opcjonalnie)
Zintegrowany terminal nadawczo-odbiórczy 10/100/1000
Obsluguje 32 bitowe PCI w wersji 2.3 o częstotliwościach 33/66-MHz
Obsługuje wpełni standard IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
Możliwe operacje 10/100 Mb/s N-way Auto-negotiation
Zdolność Half/Full duplex
Obsługuje Wake-on-LAN ( WOL) i zdalne wake-up
Zintegrowana obsługa sieci LAN posiada następujące właściwości:
Multi-Language Translation
Polski
Zintegrowane We/Wy
Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:
Dwa gniazda PS/2 dla myszy i klawiatury
Jedno gniazdo szeregowe
Jedno gniazdo równoległe
Jedno gniazdo VGA
Cztery gniazda USB
Jedno gniazdo 1394 (opcjonalnie)
Jedno gniazdo LAN (opcjonalnie)
Wejście mikrofonowe, wejście audio i 8-kanałowe wyjście High Definition Audio
Firmowy BIOS
Płyta głwna wyposażona jest w BIOS firmy Award, który pozwala użytkownikowi konfigurować wiele cech systemu włączając w to następujące właściwości:
Zarządzanie poborem mocy
Alarmy typu Wake-up
Parametry pracy procesora
Ustalenia szybkoœci pracy procesora i pamiêci
BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara procesora.
Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie bez uprzedniego powiadomienia.
Multi-Language Translation
Česky
Čipy northbridge (NB) 945G a southbridge (SB) ICH7 jsou založeny na inovativní a škálovatelné architektuře s ověřenou spolehlivostí a výkonností.
945G (NB)
Podporuje 32bitové adresování, umožòující CPU pøistupovat k celému adresovému prostoru pamìti 4 GB.
2 GB/s přímé rozhraní DMI (Direct Media Interface) pro ICH7 (1 GB/s) v obou směrech.
Podpora jednoho rozhraní PCI Express x16 pro grafiku, zcela splòující základní požadavky standardu PCI Express, revize 1.0a.
Podpora 256 MB, 512 MB a 1 Gb DDR2 technologií pro zařízení x8 a x16
Podpora 3D nastavení a vykreslovacího jádra s Jádro pro zobrazování textur ve vysoké kvalitě
Paměť
Paměti DDR2 667/533/400 DDR SDRAM s dvoukanálovou architekturou
Instalovat je možné až dvě DIMM moduly bez vyrovnávací pamìti
Až 1 GB pamìti na jeden modul DIMM s maximální velikostí pamìti do 2 GB
Čipová sada
ICH7 (SB)
Vylepšený řadič DMA, řadič přerušení a funkcí časovače
Splňuje základní požadavky standardu PCI Express, revize 1.0a
Splňuje požadavky standardu PCI 2.3
Splňuje požadavky standardu Serial ATA II
Integrované hostitelské řadiče USB 2.0 podporující až osm portů
Integrovaný řadič LAN
Splňuje požadavky standardu Hi–Fi audiokodeku AC’97/Intel s podporou 8kánlových zvukových výstupů
Integrovaný řadič IDE podporující Ultra ATA100/66/33
Vlastnosti
Procesor
Tato základní deska používá typ LGA775 Intel CoreTM 2 Duo/Pentium D/Pentium 4/Celeron D , který má následující vlastnosti:
Určená pro procesory Intel Core™ 2 Duo//Pentium D/Pentium 4/ Celeron D
Podporuje taktování systémové sběrnice (FSB) na frekvenci 1066/800/533 MHz
Podporuje technologii CPU „Hyper-Threading“
Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl připojen ke dvěma procesorům, protože je možné pracovat se dvěma toky programového kódu (vlákny) paralelně najednou, přičemž jsou k dispozici samostatné „logické“ procesory umístěné v rámci jednoho fyzického procesoru.
Grafika
Renderovací grafické jádro 3D
Podpora zónového renderování
Jádro pro zobrazování textur ve vysoké kvalitě
Multi-Language Translation
Česky
Zvuk (volitelně)
8 kanálů převodníku DAC podporuje 24/20/16bitový formát PCM pro zvukový výstup 7.1
Podpora vzorkovací frekvence převodníku DAC 192k/96k/48k/44,1kHz
Podpora napájení: Digitální: 3,3 V; Analogové: 3,5 V ~ 5,25 V
Splňuje požadavky standardu Microsoft WHQL/WLP 2.0
Kompatibilita s Direct Sound 3DTM
Výstup enkodéru Dolby Digital pro použití ve spojení se spotřební elektronikou
Splňuje požadavky standardu Hi–Fi audiokodeku Intel, s podporou 8kanálového D/A převodníku s odstupem šumu od zvuku 95 dB
Kompatibilita: 192/96/48/44,1 kHz s 24/20/16bitovým vzorkováním
Napájení: Digitální: 3,3 V; Analogové: 3,3 V / 5,0 V
Všechny analogové vstupní a výstupní konektory jsou stereo, plug & play
Splňuje požadavky standardu Microsoft WHQL/WLP 2.0
Kompatibilita s Direct Sound 3DTM
Výstup enkodéru Dolby Digital pro použití ve spojení se spotřební elektronikou
Splňuje požadavky standardu AC’97 2.3
Podpora 6kanálového zvukového kodeku určeného pro multimediální PC systémy
Nabízí tří analogové linkové stereo vstupy s 5bitovým řízení hlasitosti:
LINE-IN, CD, AUX
Splňuje požadavky standardu Microsoft WHQL/WLP 2.0
Vestavění síťové rozhraní LAN (volitelně)
Integrovaný transceiver 10/100/1000
Podpora rozhraní PCI v2.3, 32bitové, 33/66MHz
Plná podpora rozhraní IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
10/100 Mb/s Ncestné automatické přepínání provozu
Podpora plného/polovičního duplexního provozu
Podpora funkce Wake–on–LAN (WOL) a vzdálené aktivace
Vestavěné síťové rozhraní LAN nabízí následující možnosti:
1394a FireWire (volitelné)
Shoda se standardem jednočipového řadiče IEEE 1394-1995 a IEEE1394a-2000
2 integrované porty 400 Mbit PHY pro sběrnici PCI
Podporuje napájení 3,3 V s tolerancí vstupu 5 V
Základní deska podporuje sběrnici Ultra DMA s přenosovými rychlostmi 100/66 MB/s.
Základní deska je dodávána s následujícími možnostmi rozšíření
Jedna patice PCI Express x 16 pro grafickou kartu
Jedna patice PCI Express x1
Dvě 32bitové patice PCI v2.3
Jeden nízkoprofilový 40kolíkový konektor IDE podporující připojení dvou zařízení standardu IDE
Jedno rozhraní pro disketovou mechaniku
Čtyři 7kolíkové konektory SATA
Možnosti rozšíření
Multi-Language Translation
Česky
Integrovaný vstup/výstup
Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:
Dva porty PS/2 pro myš a klávesnici
Jeden sériový port
Jeden paralelní port
Jeden port VGA
Čtyři porty USB
Jeden port 1394 (volitelně)
Jeden port LAN (volitelně)
Zvukové konektory pro mikrofon, zvukový vstup a 8kanálový Hi-Fi zvukový výstup
Firmware BIOS
Základní deska využívá BIOS formy Award, který uživateli umožňuje nakonfigurovat mnoho systémových parametrů, včetně následujících:
Řízení spotřeby
Alarmy při spouštění systému
Parametry CPU
Časování CPU a paměti
Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence procesoru.
Některé technické parametry hardware a software se mohou měnit bez předchozího upozornění.
Multi-Language Translation
Română
Seturile de chipuri 945G Northbridge (NB) şi ICH7 Southbridge (SB) se bazează pe o arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi performanţă.
945G (NB)
Sprijină adresarea host bus (bus gazdă) de 32 biţi, permiţând unităţii centrale să acceseze întreaga cantitate de memorie de 4 GB.
Interfaţă Direct Media (DMI) punct la punct pe 2 GB/s pentru ICH7 (1 GB/s) în ambele direcţii.
Sprijină PCI Express de 16x pentru interfaţa grafică, este pe deplin compatibil cu versiunea 1.0a a specificaţiei de bază PCI Express.
Este compatibil cu tehnologiile de 256-Mb, 512-Mb şi 1-Gb DDR2, pentru unităţi de viteza 8x sau 16x
Suport pentru motor de configurare şi procesare 3D, precum şi motor de texturare de cea mai bună
Memoria
Module DDR SDRAM DDR2 667/533/400 cu arhitectură cu canal dual
Poate funcţiona cu două module DIMM fără zonă tampon
Poate funcţiona cu module DIMM de cel mult 1 GB, iar cantitatea maximă de memorie este de 2 GB
Setul de chipuri
ICH7 (SB)
Controler DMA îmbunătăţit, controler de întreruperi şi funcţii de temporizare
Compatibil cu specificaţia de bază PCI Express, versiunea 1.0a
Compatibil cu specificaţia PCI 2.3
Compatibil cu specificaţie Serial ATA II
Controler gazdă USB 2.0 integrat, care suportă cel mult opt porturi USB 2.0
Controler LAN integrat
Compatibilitate cu specificaţiile AC’97/Intel High Definition Audio Codec, suportând ieşiri audio pe 8 canale
Controler IDE integrat, suportând Ultra ATA100/66/33
Caracteristici
Procesorul
Placa de bază utilizează Intel Core™2 Duo/Pentium D/Pentium 4/ Celeron D de tip LGA775 cu următoarele caracteristici:
Acomodează procesoare Intel Core™2 Duo/Pentium D/ Pentium 4/ Celeron D
Funcţionează cu bus sistem (FSB) de 1066/800/533 MHz
Este compatibilă cu unităţi centrale dotate cu tehnologia „Hyper­Threading”
Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum ar exista două procesoare, putând fi rulate în paralel două fire, fiecare pe câte un procesor „logic” separat, aflate pe acelaşi procesor fizic.
Grafică
Motor de configurare şi randare 3D
Permite randare de zone
Motor de texturare de înaltă calitate
1394a Fire Wire (opţional)
compatibil cu un host controller cu un singur chip pentru IEEE 1394-1995 şi IEEE1394a-2000
400 Mbit 2-Port PHY integrat pentru PCI Bus
sursă de alimentare 3.3V cu input de 5V toleranţă
Multi-Language Translation
Română
Onboard LAN (opţional)
Unitate de emisie/recepţie 10/100/1000 integrat
Suportă PCI, versiunea 2.3, de 32 biţi, la 33/66 MHz
compatibil pe deplin cu standardul IEEE 802.3, IEEE 802.3u, IEEE
802.3ab
Operare10/100 Mb/s N-way Auto-negotiation
Suportă modul de operare duplex total/semi-duplex
Suport pentru funcţiile Wake-on-LAN ( WOL) şi trezire la distanţă
Onboard LAN are următoarele caracteristici:
Placa de bază suportă bus mastering UltraDMA cu viteze de transfer de 100/66 MB/s
Placa de bază este dotată următoarele posibilităţi de extindere:
Un slot PCI Express x16 pentru interfaţa grafică
Un slot PCI Express x1
Două
sloturi de 32 biţi compatibile PCI, versiunea 2.3
O interfaţă IDE 40 cu profil plat care poate deservi două unităţi IDE
O interfaţă pentru unitate floppy
Patru conectoare SATA 7
Opţiuni de extindere
Audio (opţional)
Suport DAC 8 canale format PCM 24/20/16-bit pentru soluţii audio 7.1
Suport 192K/96K/48K/44.1KHz DAC sample rate
Suport curent: Digital: 3.3V; Analog: 3.5V~5.25V
Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0
Compatibil cu Direct Sound 3D
TM
Ieşire codificator Dolby Digital pentru aparate electronice de larg consum
Compatibilitate cu specificaţia Intel High Definition Audio, suportând DAC pe 8 canale cu raport sunet/paraziţi de 95 dB
Compatibil cu: 192/96/48/44,1 kHz, la 24/20/16 biţi
Sursă de alimentare: digitală: 3,3 V; analoagă: 3,3 V / 5,0 V
Toate mufele analoage sunt cu redistribuire intrare şi ieşire stereo pentru configurare automată analoagă
Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0
Compatibil cu Direct Sound 3D
TM
Ieşire codificator Dolby Digital pentru aparate electronice de larg consum
Compatibil cu specificaţia AC’97 2.3
Suportă CODEC cu şase canale audio destinate sistemelor multimedia ale calculatoarelor
Oferă trei intrări audio analoge stereo, cu un control al volumului sonor de 5 biţi: Intrare audio, CD, AUX
Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0
Multi-Language Translation
Română
I/O integrată
Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:
Două porturi PS/2, pentru mouse şi tastatură
Un port serial
Un port paralel
Un port VGA
Patru porturi USB
Un port 1394 (opţional)
Un port LAN (opţional)
Mufe audio pentru microfon, intrare audio şi pentru 8 canale audio de ieşire de înaltă fidelitate
Firmware BIOS
Placa de bază utilizează Award BIOS, care permite utilizatorului să configureze mai mulţi parametri ai sistemului, cum ar fi:
Gestionarea energiei
Alarme de trezire
Parametri CPU
Temporizare CPU şi memorie
Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale procesorului.
Anumite specificaţii hardware şi elemente de software pot fi modificate fără înştiinţare prealabilă.
Multi-Language Translation
Български
Чипсетът със северен мост 945G (NB) и южен мост ICH7 (SB) е изграден на базата на оригинална архитектура с възможност за надстройка с доказана надеждност и производителност.
945G (NB)
32-bit адресация на шината, което позволява на процесора достъп към пълното адресно пространство на паметта
4GB.
Директен медия интерфейс (DMI) 2 GB/s point-to-point към ICH7, (1 GB/s във всяка посока).
поддръжка на шина PCI Express x16 за графичен интерфейс, напълно съвместима с шината
PCI Express Base ревизия 1.0a.
поддръжка на технологии 256-Mb, 512-Mb и 1-Gb DDR2 за x8 и x16 устройства
Поддръжка на
3D setup, render engine и висококачествено
ядро за текстури.
Памет
Дву-канална архитектура на паметта DDR2 667/533/400 DDR SDRAM
поддръжка на до два небуферирани DIMM слота
до 1 GB памет на 1 DIMM канал с максимален капацитет 2 GB
Чипсет
ICH7 (SB)
подобрен DMA Контролер, контролер на прекъсванията и часовник
поддръжка на шината PCI Express Base, ревизия 1.0a
поддръжка на шината PCI 2.3
съвместимост със спецификацията Serial ATA II
интегриран контролер USB 2.0 с поддръжка на до осем порта USB 2.0
интегриран мрежов контролер
Съвместимост с AC’97/Intel High Definition Audio Codec(s) с поддръжка на 8-канални аудио изходи
интегриран контролер IDE с поддръжка на Ultra ATA100/66/33
Спецификация
Процесор
Тази дънна платка използва сокет LGA775 за процесори Intel Core™2 Duo/ Pentium D/Pentium 4/ Celeron D и поддържа следните спецификации:
поддръжка на процесори Intel Core™ 2 Duo/Pentium D/ Pentium 4/ Celeron D
поддръжка на системна шина със скорост 1066/800/533MHz
поддръжка на процесори с технология “Hyper-Threading"
Технологията “
Hyper-Threading" позволява да се “излъже” операционната система, че работи на два процесора, което дава възможност за паралелното изпълнение на две задачи на два отделни “логически” процесора в един и същ физически процесор.
Графичен чип
3D setup и render engine
поддръжка на Zone Rendering
висококачествено ядро за текстури
1394a FireWire контролер (опция)
host контролер на един чип за поддръжка на интерфейси IEEE 1394-
1995 и IEEE1394a-2000
Интегриран 400-мегабитов PHY интерфейс с два порт за PCI шината
Захранване 3.3V с толеранс 5V
Multi-Language Translation
Български
Дънната платка поддържа шина UltraDMA 100/66 MB/s
Дънната платка има следните разширителни възможности:
Един слот PCI Express x16 за графичен интерфейс
Един слот PCI Express x1
Два слота 32-bit PCI v2.3
Един нископрофилен 40-pin IDE колектор с поддръжка на две IDE устройства
Един конектор за флопидисково устройство
Четири 7-pin SATA конектора
Възможности за разширяване
Аудио (опция)
8-канален цифрово-аналогов преобразовател с поддръжка на 24/20/16-bit PCM формат за 7.1 канален звук.
Поддръжка на честота 192K/96K/48K/44.1KHz
Захранване: цифрово: 3.3V; аналогово: 3.5V~5.25V
Съвместим със спецификацията Microsoft WHQL/WLP 2.0
съвместимост с Direct Sound 3DTM
Изход с вграден Dolby Digital Encoder
Съвместимост с Intel High Definition Audio, с поддръжка на 8-канални цифрово-аналогови преобразователи със съотношение звук/шум 95dB
съвместимост с: 192/96/48/44.1 KHz на 24/20/16 bits
Захранване: Цифрово: 3.3V; Аналогово: 3.3V/5.0V
Всички аналогови гнезда са стерео, с възможност за аналогов режим plug & play
Съвместим със спецификацията Microsoft WHQL/WLP 2.0
съвместимост с Direct Sound 3DTM
Изход с вграден Dolby Digital Encoder
Аудио Кодек съвместим с AC’97 v2.3
Поддръжка на 6-канален аудио кодек за мултимедийни компютърни системи
Три аналогови линейни стерео входа с 5-битов контрол на силата на звука: Line-in, CD, AUX
Съвместим със спецификацията Microsoft WHQL/WLP 2.0
Интегриран мрежов контролер (опция)
Интегриран 10/100/1000 контролер
Поддръжка на PCI v2.3, 32-bit, 33/66-MHz
Пълна поддръжка на
IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
режими на работа 10/100 Mb/s N-way с автоматично съгласуване
Поддръжка на режими half/full duplex
поддръжка на функция за “събуждане” Wake-On-LAN и дистанционен wake-up
Спецификация на интегрирания мрежов контролер:
Multi-Language Translation
Български
Интегриран Вход/Изход контролер
Дънната платка има пълен набор от I/O портове и конектори:
два PS/2 порта за мишка и клавиатура
един сериен порт
един паралелен порт
един VGA порт
четири USB порта
един 1394 порт (опция)
един LAN порт (опция)
аудио жак за микрофон (вход), линеен вход, линеен изход и изход за 8­канално High Definition аудио
BIOS Firmware
Дънната платка използва Award BIOS с възможност за различни системни настройки, включително
управление на захранването
Wake-up аларми
параметри на процесора
синхронизиране на процесора и паметта
настройка на скоростта на часовника на процесора
Хардуерните и софтуерни спецификации и параметри могат да бъдат изменени без предупреждение.
Loading...