ECS 848P-A7 User Manual

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 5.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.

MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.

Other product names used in this manual are the properties of their respective owners and are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesired operation

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1

Introducing the Motherboard

Describes features of the motherboard.

Go to

page 1

Chapter 2

Installing the Motherboard

Chapter 3

Using BIOS

Chapter 4

Using the Motherboard Software

Describes installation of motherboard components.

Go to

Provides information on using the BIOS Setup Utility.

Go to

Describes the motherboard software

Go to

page 7

page 25

page 47

Preface

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

ABLE OF CONTENTSABLE OF CONTENTS

Preface i

iii

Chapter 1

Introducing the Motherboard 1

Introduction.................................................................................................1

Feature..........................................................................................................2

Motherboard Components........................................................................4

Chapter 2

Installing the Motherboard 7

Safety Precautions......................................................................................7

Choosing a Computer Case.......................................................................7

Installing the Motherboard in a Case......................................................7

Checking Jumper Settings.........................................................................8

Setting Jumpers..............................................................................8

Checking Jumper Settings..............................................................9

Jumper Settings..............................................................................9

Connecting Case Components...............................................................10

Front Panel Connector.................................................................12

Installing Hardware...................................................................................13

Installing the Processor...............................................................13

Installing Memory Modules.........................................................15

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17

Installing a Floppy Diskette Drive...............................................19

Installing Add-on Cards..............................................................20

Connecting Optional Devices......................................................21

Connecting I/O Devices..........................................................................24

7 7

Chapter 3

Using BIOS 25

About the Setup Utility............................................................................25

The Standard Configuration........................................................25

Entering the Setup Utility..............................................................25

Updating the BIOS.......................................................................27

Using BIOS................................................................................................27

Standard CMOS Features...........................................................28

Advanced BIOS Features.............................................................30

Advanced Chipset Features.........................................................33

25 25

Integrated Peripherals..................................................................35

Power Management Setup............................................................39

PNP/PCI Configurations..............................................................41

PC Health Status..........................................................................42

Frequency/Voltage Control...........................................................43

Load Performance Defaults .............................................................44

Load Optimized Defaults.............................................................44

Set Supervisor/User Password....................................................44

Save & Exit Setup Option.............................................................45

Exit Without Saving......................................................................45

Chapter 4

47 47

Using the Motherboard Software 47

About the Software CD-ROM................................................................47

Auto-installing under Windows 98/ME/2000/XP................................47

Running Setup..............................................................................48

Manual Installation..................................................................................50

Utility Software Reference.......................................................................50

Multi-Language Translation

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing the 848P-A7 motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA775 Socket Intel Pentium 4/Celeron D/Pentium D processors for high-end business or personal desktop markets.

The motherboard incorporates the 848P Northbridge (NB) and ICH5 Southbridge (SB) chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 800/533 MHz with maximum theoretical BW of 6.4 GB/s. The momory controller supports DDR memory DIMM frequencies of 400/333/266 MHz. It supports two DDR Sockets with up to maximum memory of 2 GB. DDR Maximum memory bandwidth of 3.2 GB/s in single-channel mode is supported. One AGP interface supports AGP 3.0 including 8X/4X AGP Data Transfers and 8X/4X Fast Write Protocol.

The ICH5 Southbridge supports five PCI slots which are PCI 2.3 compliant. It accomodates eight USB 2.0 ports for Serial Transfers at maximum 480 Mb/s. This motherboard complies with AC’97 2.3 codecs and supports up to six channels of PCM audio output (full AC3 decode). Two onboard IDE connectors support 4 IDE devices in Ultra ATA100/66/33 mode. The Southbridge integrates two Serial ATA host controllers that is SATA v1.0 compliant, supporting two SATA ports with maximum transfer rate up to 1.5 Gb/s each.

This motherboard is equipped with advanced full set of I/O ports in the rear panel, including PS/2 mouse and keyboard connectors, one serial port, one parallel port, four USB ports, one optional LAN port, and audio jacks for microphone, line-in and line-out.

Introducing the Motherboard

Feature

Processor

This motherboard uses an LGA775 type of Pentium 4/Celeron D/Pentium D that carries the following features:

• Accommodates Intel Pentium 4/Celeron D/Pentium D processors

• Supports a system bus (FSB) of 800/533 MHz

• Supports “Hyper-Threading” technology CPU

“Hyper-Threading” technology enables the operating system into thinking it’s hooked up to two processors, allowing two threads to be run in parallel, both on separate “logical” processors within the same physical processor.

Chipset

The 848P Northbridge (NB) and ICH5 Southbridge (SB) chipset are based on an innovative and scalable architecture with proven reliability and performance.

848P (NB)

ICH5 (SB)

• Supports Hub Interface (HI) 1.5 with 266 MB/s point-topoint connection to ICH5

• Supports AGP 3.0 with 8X/4X AGP data transfers and 8X/ 4X fast writes respectively

• Supports Single-channel DDR memory interface

• Supports DDR400/333/266 DIMM modules

• Supports up to two unbuffered DIMMs with 2 GB maximum memory size

• Supports up to six PCI Masters fully compliant with PCI 2.3 specificaiton at 33 MHz

• Supports 2 channels Ultra ATA 100 bus master IDE controllers

• The SATA controller supports two SATA devices

• Compliant with AC’97 v2.3 supporting 6 Channels of audio outputs

• Supports eight USB 2.0 ports for serial transfers at 480 Mb/ s maximum

Memory

• Supports DDR400/333/266 DDR SDRAM memory module

• Accommodates two

• Up to 1 GB per DIMM with maximum memory size up to 2 GB

unbuffered DIMMs

Audio

• Compliant with AC’97 v2.3 CODEC

• Supports 6-channel audio CODEC designed for PC multimedia systems

• Provides three analog line-level stereo inputs with 5-bit volume control: Line-in, CD, AUX

• Meets Microsoft WHQL/WLP 2.0 audio requirements

Introducing the Motherboard

Onboard LAN (Optional)

This motherboard may support either of the following LAN chipset:

• Supports 10/100 Mb/s N-Way Auto negotiation operation

• Half/Full duplex capability

• Supports Wake-On-LAN(WOL) function and remote wake-up

• Integrate 10/100/1000 transceiver

• Supports PCI v2.3, 32-bit, 33/66 MHz

• Supports fully with IEEE802.3, IEEE802.3u and IEEE802.3ab

Expansion Options

The motherboard comes with the following expansion options:

• One AGP 3.0 compliant slot with 8X/4X speed (supports 1.5V AGP interface only)

• Five 32-bit PCI v2.3 compliant slots

• Two 40-pin IDE low profile headers that support four IDE devices

• One floppy disk drive interface

• Two 7-pin SATA connectors

This motherboard supports UltraDMA bus mastering with transfer rates of 100/66 MB/ s.

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One parallel port

• Four USB ports

• One LAN port (optional)

• Audio jacks for microphone, line-in and line-out

BIOS Firmware

This motherboard uses Award BIOS that enables users to configure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different processor clock speeds.

Some hardware specifications and software items are subject to change without prior notice.

Introducing the Motherboard

Motherboard Components

Introducing the Motherboard

Table of Motherboard Components

LABEL COMPONENT

1 CPU Socket

2 CPU_FAN CPU cooling fan connector 3 DIMM1~2 184-pin DDR SDRAM slots

4 FDD Floppy diskette drive connector

5 ATX1 Standard 20-pin ATX power connector

6 IDE1 Primary IDE connector

7 IDE2 Secondary IDE connector 8 PWR_FAN* Power fan connector

9 CLR_CMOS Clear CMOS jumper 10 SATA1~2 Serial ATA connectors

11 F_PANEL Front Panel switch/LED header 12 BIOS_WP BIOS protect jumper 13 SPK1 Speaker header

14 F_USB3~4 Front panel USB headers

15 IR Serial Infrared header 16 CHS1* Chassis detect header 17 JP1 LAN function enable/disable jumper

18 PCI1~5 32-bit add-on card slots

19 SPDIF1 SPDIF out header

20 AGP Accelerated Graphics Port slot 21 AUXIN1 Auxiliary In header

22 CD_IN Analog audio input header 23 F_AUDIO Front panel audio header

24 SYS_FAN Case cooling fan connector

25 ATX12V 4-pin +12V power connector

26 PAT1~2 PAT jumpers

LGA775 socket for latest Intel Pentium 4/Celeron D/Pentium D CPUs

*Stands for optional components

This concludes Chapter 1. The next chapter explains how to install the motherboard.

Introducing the Motherboard

Memo

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from static electricity

• Discharge static electricity by touching the metal case of a safely grounded object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the ATX system case. First, some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required. Secondly, this motherboard supports one or two floppy diskette drives and four enhanced IDE drives. Make sure that your case has sufficient power and space for all drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries an ATX form factor of 305 x 244 mm. Choose a case that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case.

Most system cases have mounting brackets installed in the case, which correspond the holes in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT

SHORT OPEN

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

Jumper Settings

Jumper

JP1

CLR_CMOS

BIOS_WP

PAT1

PAT2

Type

3-pin

Description

LAN FUNCTION

CLEAR CMOS

BIOS FLASH PROTECT

Turbo Mode

Installing the Motherboard

Setting (default)

1-2: ENABLE

2-3: DISABLE

1-2: CLEAR

2-3: NORMAL

Before clearing the CMOS, make sure to turn off the system.

OPEN: UNPROTECT

SHORT: PROTECT

1-2: DISABLE

2-3: ENABLE

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the case cooling fan connector to SYS_FAN. 3 Connect the power fan connector to PWR_FAN (optional). 4 Connect the case speaker cable to SPK1. 5 Connect the case switches and indicator LEDs to the F_PANEL. 6 Connect the standard power supply connector to ATX1. 7 Connect the auxiliary case power supply connector to ATX12V.

SYS_FAN/PWR_FAN (optional): FAN Power Connectors

Pin Signal Name Function

1 GND System Ground 2 +12V Power +12V 3 Sense Sensor

CPU_FAN: FAN Power Connector

Pin Signal Name Function

1 GND System Ground 2 +12V Power +12V 3 Sense Sensor

4 PWM CPU FAN control

Installing the Motherboard

SPK1: Internal speaker

Pin Signal Name

1 VCC

2 Key 3 GND

4 Signal

ATX1: ATX 20-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 11 +3.3V

2 +3.3V 12 -12V 3 Ground 13 Ground

4 +5V 14 PS ON#

5 Ground 15 Ground

6 +5V 16 Ground 7 Ground 17 Ground 8 PWRGD 18 -5V

9 +5VSB 19 +5V

10 +12V 20 +5V

ATX12V: ATX 12V Power Connector

Pin Signal Name

1 Ground

2 Ground 3 +12V

4 +12V

Installing the Motherboard

Front Panel Connector

The front panel connector (F_PANEL) provides a standard set of switch and LED connectors commonly found on ATX or micro-ATX cases. Refer to the table below for information:

Pin Signal Function Pin Signal Function

1 HD_LED_P Hard disk LED(+) 2 FP PWR/SLP *MSG LED(+)

3 HD_LED_N Hard disk LED(-)

5 RST_SW_N Reset Switch(-)

7 RST_SW_P Reset Switch(+)

9 RSVD Reserved

* MSG LED (dual color or single color)

4 FP PWR/SLP *MSG LED(-)

6 PWR_SW_P Power Switch(+)

8 PWR_SW_N Power Switch(-)

10 Key No pin

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change these settings by making changes to jumpers on the motherboard, or changing the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.

Warning: Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

This motherboard has an LGA775 processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

Installing the Motherboard

CPU Installation Procedure

The following illustration shows CPU installation components.

A. Read and follow the instructions shown on the

sticker on the CPU cap.

B. Unload the cap

· Use thumb & forefinger to hold the lifting tab of the cap.

· Lift the cap up and remove the cap completely from the socket.

C. Open the load plate

· Use thumb & forefinger to hold the hook of the lever, pushing down and pulling aside unlock it.

· Lift up the lever.

· Use thumb to open the load plate. Be careful not to touch the contacts.

D. Install the CPU on the socket

· Orientate CPU package to the socket. Make sure you match triangle marker to pin 1 location.

E. Close the load plate

· Slightly push down the load plate onto the tongue side, and hook the lever.

· CPU is locked completely.

F. Apply thermal grease on top of the CPU.

G. Fasten the cooling fan supporting base onto the CPU socket on the motherboard.

H. Make sure the CPU fan is plugged to the CPU fan connector. Please refer to the CPU cooling fan user’s manual for more detail installation procedure.

To achieve better airflow rates and heat dissipation, we suggest that you

use a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.

DO NOT remove the CPU cap from the socket before installing a CPU.

Return Material Authorization (RMA) requests will be accepted only if the

3. motherboard comes with the cap on the LGA775 socket.

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates two memory modules. It can support two 184-pin unbuffered DIMMs, DDR400/333/266. The total memory capacity is 2 GB.

DDR SDRAM memory module table

Memory module Memory Bus

DDR266 DDR333

DDR400

You must install at least one module in any of the two slots. Each module can be installed with 128 MB to 1 GB of memory; total memory capacity is 2 GB.

Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

133MHz 166MHz 200MHz

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR SDRAM only. 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the notches

in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it seats

correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.

6 Install any remaining DIMM modules.

Installing the Motherboard

Table A: DDR (memory module) QVL (Qualified Vendor List)

The following DDR400 memory modules have been tested and qualified for use with this motherboard.

Size Vendor Module Name

128MB

Infineon HYS64D16301GU-5-B NANYA NT128D64SH4B1G-5 NANYA NT128D64SH4B1G-5T

256MB

Infineon HYS64D32300GU-5-B

Infineon HYS64D32300HU-5-C

Micron MT8VDDT3264AG-40BC4 NANYA NT256D64S88B1G-5T Ramaxel Infineon

SAMSUNG M368L3223DTM-CC4

Apacer Infineon

512MB

Apacer MOSEL

Infineon HYS64D64320HU-5-C Infineon HYS64D64300HU-5-C

1GB

A-DATA VITESTA

NANYA NT1GD64S8HB0G-5T

Installing the Motherboard

Installing a Hard Dish Drive/CD-ROM/SATA Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive.

About IDE Devices

Your motherboard has a primary and secondary IDE channel interface (IDE1 and IDE2). An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.

You must orient the cable connector so that the pin1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.

IDE1: Primary IDE Connector

The first hard drive should always be connected to IDE1.

IDE2: Secondary IDE Connector

The second drive on this controller must be set to slave mode. The cinfiguration is the same as IDE1.

IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.

Installing the Motherboard

About SATA Connectors

This motherboard features two SATA connectors supporting a total of two drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard (see page 20) and follow the illustration below to install the SATA hard drives.

Installing Serial ATA Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with an SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

SATA cable (optional)

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

This motherboard does not support the “Hot-Plug” function.

SATA power cable (optional)

Installing the Motherboard

Installing a Floppy Diskette Drive

The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.

You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.

FDD: Floppy Disk Connector

This connector supports the provided floppy drive ribbon cable. After connecting the single end to the onboard floppy connector, connect the remaining plugs on the other end to the floppy drives correspondingly.

Installing the Motherboard

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

AGP Slot

PCI 1~5 Slots

The AGP slot is used to install a graphics adapter that supports the 8X/4X AGP specification. It is AGP 3.0 compliant.

This motherboard is equipped with five standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

Installing the Motherboard

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the slot you

are going to use.

2 Install the edge connector of the add-on card into the expansion slot. Ensure

that the edge connector is correctly seated in the slot.

3 Secure the metal bracket of the card to the system case with a screw.

For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

Installing the Motherboard

SPDIF1: SPDIF out header

This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.

Pin Signal Name Function

1 SPDIF SPDIF digital output 2 +5VA 5V analog Power 3 Key No pin 4 GND Ground

F_AUDIO: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access.

Pin Signal Name Function

1 AUD_MIC Front Panel Microphone input signal 2 AUD_GND Ground used by Analog Audio Circuits 3 AUD_MIC_BIAS Microphone Power

4 AUD_VCC Filtered +5V used by Analog Audio Circuits 5 AUD_F_R Right Channel audio signal to Front Panel 6 AUD_RET_R Right Channel Audio signal to Return from Front Panel 7 REVD Reserved

8 Key No Pin 9 AUD_F_L Left Channel Audio signal to Front Panel 10 AUD_RET_L Left Channel Audio signal to Return from Front Panel

Pin Signal Name

CD-IN: Analog Audio Input header

Pin Signal Name Function

1 CD in_L CD In left channel 2 GND Ground 3 GND Ground 4 CD in_R CD In right channel

SATA1/SATA2: Serial ATA connectors

These connectors are use to support the new Serial ATA devices for the highest date transfer rates (1.5 Gb/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

Pin Signal Name

Pin Signal Name Function

1 Ground 2 TX+

3 TX- 4 Ground 5 RX- 6 RX+

7 Ground - -

Pin Signal Name

Installing the Motherboard

F_USB3/4: Front Panel USB header

The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

Pin Signal Name Function

1 USBPWR Front Panel USB Power 2 USBPWR Front Panel USB Power 3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal 5 USB_FP_P0+ USB Port 0 Positive Signal 6 USB_FP_P1+ USB Port 1 Positive Signal

7 GND Ground

8 GND Ground 9 Key No pin 10 USB_FP_OC0 Overcurrent signal

Please make sure that the USB cable has the same pin assignment as indicatged above. A different pin assignment may cause damage or system hang-up.

IR: Serial infrared header

The motherboard supports an Infrared (IR) data header. Infrared header allow the wireless exchange of information between your computer and similarly equipped devices such as printers, laptops, Personal Assistants (PDAs), and other computers.

Pin Signal Name Function

1 Not assigned Not assigned 2 Key No pin 3 +5V IR Power

4 GND Ground 5 IRTX IrDA serial output 6 IRRX IrDA serial input

AUXIN1: Auxliary In header

Pin Signal Name Function

1 AUX_L AUX In left channel 2 GND Ground 3 GND Ground 4 AUX_R AUX In right channel

Installing the Motherboard

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

Parallel Port (LPT1) Use LPT1 to connect printers or other parallel communications

Serial Port Use the COM port to connect serial devices such as mice or (COM1) fax/modems. COM1 is identified by the system as COM1/3.

LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your computer

USB Ports Use the USB ports to connect USB devices.

Audio Ports Use the three audio ports to connect audio devices. The first jack

This concludes Chapter 2. The next chapter covers the BIOS.

devices.

to the Network.

is for stereo line-in signal. The second jack is for stereo line-out signal. The third jack is for microphone.

Installing the Motherboard

Chapter 3

Using BIOS

About the Setup Utility

The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Using BIOS

Press DEL to enter SETUP

Pressing the delete key accesses the BIOS Setup Utility:

Phoenix-AwardBIOS CMOS Setup Utility:

Standard CMOS Features

Advanced BIOS Features Load Performance Defaults

Advanced Chipset Features Load Optimized Defaults

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Esc: Quit

F10: Save & Exit Setup

Time, Date, Hard Disk Type...

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

ESC Exits the current menu

oqrtoqrt

oqrt Scrolls through the items on a menu

oqrtoqrt

+/-/PU/PD Modifies the selected field’s values

F10 Saves the current configuration and exits setup

F1 Displays a screen that describes all key functions

F5 Loads previously saved values to CMOS

F6 Loads a minimum configuration for troubleshooting

F7 Loads an optimum set of values for peak performance

Frequency/Voltage Control

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

: Select Item

mnlk

Using BIOS

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to allow

BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Advanced

BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.

3 Create a bootable system disk. (Refer to Windows online help for information

on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s Web

site. Copy these files to the system diskette you created in Step 3.

5 Turn off your computer and insert the system diskette in your computer’s

diskette drive. (You might need to run the Setup Utility and change the boot priority items on the Advanced BIOS Features Setup page, to force your computer to boot from the floppy diskette drive first.)

6 At the A:\ prompt, type the Flash Utility program name and press <Enter>.

7 Type the filename of the new BIOS in the “File Name to Program” text box.

Follow the onscreen directions to update the motherboard BIOS.

8 When the installation is complete, remove the floppy diskette from the diskette

drive and restart your computer. If your motherboard has a Flash BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten.

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a

triangle

f .

f) lead to submenus that enable you to change the

Using BIOS

Standard CMOS Features

This option displays basic information about your system.

Phoenix-AwardBIOS CMOS Setup Utility Standard CMOS Features

Date (mm:dd:yy) Mon, Nov 17 2005 Time (hh:mm:ss) 13 : 4 : 54

IDE Channel 0 Master

IDE Channel 0 Slave

IDE Channel 1 Master

IDE Channel 1 Slave

Drive A [1.44M, 3.5 in.] Floppy 3 Mode Support [Disabled]

Video [EGA/VGA] Halt On [All Errors]

Base Memory 640K Extended Memory 261120K Total Memory 262144K

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Date and Time

The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility.

fIDE Devices (None)

Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices (Master and Slave). In addition, this motherboard supports two SATA channels (Primary and Secondary) and each channel allows one SATA device to be installed. Use these items to configure each device on the IDE channel.

Press <Enter> to display the IDE submenu:

Phoenix-AwardBIOS CMOS Setup Utility

IDE Primary Master

IDE HDD Auto-Detection [ Press Enter] IDE Channel 1 Master [Auto] Access Mode [Auto]

Capacity 0 M B Cylinder 0 Head 0 Precomp 0 Landing Zone 0 Sector 0

Item Help

Menu Level

Change the day, month, year and century.

Item Help

Menu Level

To auto-detect the HDD’s size, head...on this channel

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

IDE HDD Auto-Detection

Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically detect and configure an IDE device on the IDE channel.

If you are setting up a new hard disk drive that supports LBA mode, more than one line will appear in the parameter box. Choose the line that lists LBA for an LBA drive.

Using BIOS

IDE Channel 0/1 Master/Slave (Auto)

Leave this item at Auto to enable the system to automatically detect and configure IDE devices on the channel. If it fails to find a device, change the value to Manual and then manually configure the drive by entering the characteristics of the drive in the items described below.

Refer to your drive’s documentation or look on the drive casing if you need to obtain this information. If no device is installed, change the value to None.

Before attempting to configure a hard disk drive, ensure that you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk.

Access Mode (Auto)

This item defines ways that can be used to access IDE hard disks such as LBA (Large Block Addressing). Leave this value at Auto and the system will automatically decide the fastest way to access the hard disk drive.

Press <Esc> to return to the Standard CMOS Features page.

Drive A (1.44M, 3.5 in./None)

This item defines the characteristics of any diskette drive attached to the system.

Floppy 3 Mode Support (Disabled)

Floppy 3 mode refers to a 3.5-inch diskette with a capacity of 1.2 MB. Floppy 3 mode is sometimes used in Japan.

Video (EGA/VGA)

This item defines the video mode of the system. This motherboard has a built-in VGA graphics system; you must leave this item at the default value.

Halt On (All Errors)

This item defines the operation of the system POST (Power On Self Test) routine. You can use this item to select which types of errors in the POST are sufficient to halt the system.

Base Memory, Extended Memory, and Total Memory

These items are automatically detected by the system at start up time. These are display-only fields. You cannot make changes to these fields.

Using BIOS

Advanced BIOS Features

This option defines advanced information about your system.

CPU Feature [Press Enter]

Hard Disk Boot Priority [Press Enter]

CPU L3 Cache [Enabled] Hyper-Threading Technology [Enabled] Quick Power On Self Test [Enabled] First Boot Device [Floppy] Second Boot Device [Hard Disk] Third Boot Device [CDROM] Boot Other Device [Enabled] Boot Up Floppy Seek [Disabled] Boot Up NumLock Status [On] Gate A20 Option [Fast] Typematic Rate Setting [Disabled]

Typematic Rate (Chars/Sec ) 6 Typematic Delay (Msec) 250

Security Option [Setup]

APIC Mode [Enabled] OS Select For DRAM > 64MB [Non-OS2] HDD S.M.A.R.T. Capability [Disabled]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

CPU Feature (Press Enter)

Users please note that this function is only available for Prescott CPUs. Scroll to this item and press <Enter> to view the following screen:

Phoenix-AwardBIOS CMOS Setup Utility Advanced BIOS Features

Phoenix-AwardBIOS CMOS Setup Utility CPU F eature

Item Help

Menu Level

Delay Prior to thermal [16 Min] Thermal Management [Thermal Monitor 1] TM2 Bus Ratio [0 X] TM2 Bus VID [0.8375V] Limit CPUID MaxVal [Disabled] Executed Disabled Bit [Enabled]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6”Fail-Safe Defaults F7:Optimized

Item Help

Menu Level

Thermal Monitor 1 (On die throtting)

Thermal Monitor 2 Ratio & VID transition

Delay Prior to Thermal (Thermal Monitor 1)

This item enables you to set the delay time before the CPU enters auto thermal mode.

Thermal Management (Thermal Monitor 1)

This item displays CPU’s temperature and enables you to set a safe temperature to Prescott CPU.

Using BIOS

TM2 Bus Ratio (0X)

This item helps you to set the frequency (bus ratio) of the throttled performance that will be initiated when the on-die sensor goes from not hot to hot. You may set the bus ratio number from 0-255. This feature is available when CPU supports Thermal Monitor 2.

TM2 Bus VID (0.8375V)

This item helps you to set the voltage of the throttled performance that will be initiated when the on-die sensor goes from not hot to hot. This feature is available when CPU supports Thermal Monitor 2.

Limit CPUID MaxVal (Disabled)

This item can support Prescott CPUs for old OS. Users please note that under NT 4.0, it must be set “Enabled”, while under WinXP, it must be set “Disabled”.

Executed Disabled Bit (Enabled)

Users please leave this item in its default setting under Windows XP OS. Change the value to “Disabled” if users are to install Linux OS.

Press <Esc> to return to the Advanced BIOS Features screen.

Hard Disk Boot Priority (Press Enter)

Scroll to this item and press <Enter> to view the following screen:

Phoenix-AwardBIOS CMOS Setup Utility Hard Disk Boot Priority

1. Pri. Master:

2. Pri. Slave:

3. Sec. Master:

4. Sec. Slave:

5. USBHDD0:

6. USBHDD1:

7. USBHDD2:

8. Bootable Add-in Cards

Item Help

Menu Level

Use < > or < > to select

a device, then press <+> to move it up, or <-> to move it down the list. Press <ESC> to exit this menu.

: Move PU/PD/+/-/: Change Priority F10:Save ESC:Exit

CPU L3 Cache (Enabled)

All Prescott processors that can be installed in this mainboard use Level 3 (L3) cache memory to improve performance. Leave this item at the default value for better performance. This item is only available when you use L3 cache supported CPU.

Hyper-Threading Technology (Enabled)

This item is only available when the chipset supports Hyper-Threading and you are using a Hyper-Threading CPU.

Quick Power On Self Test (Enabled)

Enable this item to shorten the power on testing (POST) and have your system start up faster. You might like to enable this item after you are confident that your system hardware is operating smoothly.

Using BIOS

First/Second/Third Boot Device (Floppy/Hard Disk/CDROM)

Use these three items to select the priority and order of the devices that your system searches for an operating system at start-up time.

Boot Other Device (Enabled)

When enabled, the system searches all other possible locations for an operating system if it fails to find one in the devices specified under the First, Second, and Third boot devices.

Boot Up Floppy Seek (Disabled)

If this item is enabled, it checks the size of the floppy disk drives at start-up time. You don’t need to enable this item unless you have a legacy diskette drive with 360K capacity.

Boot Up NumLock Status (On)

This item defines if the keyboard Num Lock key is active when your system is started.

Gate A20 Option (Fast)

This item defines how the system handles legacy software that was written for an earlier generation of processors. Leave this item at the default value.

Typematic Rate Setting (Disabled)

If this item is enabled, you can use the following two items to set the typematic rate and the typematic delay settings for your keyboard.

• Typematic Rate (Chars/Sec): Use this item to define how many charac- ters per second are generated by a held-down key.

• Typematic Delay (Msec): Use this item to define how many milliseconds must elapse before a held-down key begins generating repeat characters.

Security Option (Setup)

If you have installed password protection, this item defines if the password is required at system start up, or if it is only required when a user tries to enter the Setup Utility.

APIC Mode (Enabled)

This item allows you to enable or disable the APIC (Advanced Programmable Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing support for up to 60 processors.

OS Select For DRAM > 64 MB (Non-OS2)

This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating system. Otherwise, leave this item at the default.

HDD S.M.A.R.T Capability (Disabled)

The S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system is a diagnostics technology that monitors and predicts device performance. S.M.A.R.T. software resides on both the disk drive and the host computer.

Report No FDD For WIN 95 (Yes)

This item determines whether the BIOS will report no FDD for Windows 95 OS.

Using BIOS

Small Logo (EPA) Show (Disabled)

Enables or disables the display of the EPA logo during boot.

Advanced Chipset Features

These items define critical timing parameters of the motherboard. You should leave the items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instability into your system.

Phoenix-AwardBIOS CMOS Setup Utility Advanced Chipset Features

DRAM Timing Selectable [By SPD] CAS Latency Time [2.5] Active to Precharge Delay [8] DRAM RAS# to CAS# Delay [4] DRAM RAS# Precharge [4] Memory Frequency For [Auto] System BIOS Cacheable [Disabled] Video BIOS Cacheable [Disabled] AGP Aperature Size (MB) [128] Init Display First [PCI Slot]

Fast Chip Select [Auto] Turbo Mode [Auto]

Item Help

Menu Level

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

DRAM Timing Selectable (By SPD)

Enables you to select the CAS latency time in HCLKs of 2, 2.5, or 3. The value is set at the factory depending on the DRAM installed. Do not change the values in this field unless you change specifications of the installed DRAM or the installed CPU.

• CAS Latency Time (2.5): This item controls the timing delay (in clock

cycles) before the DRAM starts a read command after receiving it.

• Active to Precharge Delay (8): This precharge time is the number of cycles

it takes for DRAM to accumulate its charge before refresh.

• DRAM RAS# to CAS# Delay (4): This field lets you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Disabled gives faster performance; and Enabled gives more stable performance.

• DRAM RAS# Precharge (4): Select the number of CPU clocks allocated forthe Row Address Strobe (RAS#) signal to accumulate its charge before

the DRAM is refreshed. If insufficient time is allowed, refresh may be incomplete and data lost.

Using BIOS

Memory Frequency For (Auto)

This item sets the main memory frequency. When you used an external graphics card, you can adjust this to enable the best performance for your system.

System BIOS Cacheable (Disabled)

When this item is enabled, the System BIOS will be cached for faster execution.

Video BIOS Cacheable (Disabled)

When this is enabled, the Video RAM will be cached resulting to better performance. However, if any program was written to this memory area, this may result to system error.

AGP Aperture Size (MB) (128)

This item defines the size of the aperture if you use an AGP graphics adapter. The AGP aperture refers to a section of the PCI memory address renge used for graphics memory. We recommend that you leave this item at the default value.

Init Display First (PCI Slot)

This item allows you to choose the primary display card.

Fast Chip Select (Auto)

This item allows you to read the Data transfer from CPU to GMCH.

Turbo Mode (Auto)

This item allows you to increase the performance of CPU L2 cache timing at high speed.

Using BIOS

Integrated Peripherals

These options display items that define the operation of peripheral components on the system’s input/output ports.

Phoenix-AwardBIOS CMOS Setup Utility Int egra ted P eri phera ls

OnChip IDE Device [Press Enter]

Onboard Device [Press Enter]

SuperIO Device [Press Enter]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

fOnChip IDE Device

Scroll to this item and press <Enter> to view the following screen:

Phoenix-AwardBIOS CMOS Setup Utility OnChip IDE Device

IDE HDD Block Mode [Enabled] On-chip Primary PCI IDE [Enabled] IDE Primary Master PIO [Auto] IDE Primary Slave PIO [Auto] IDE Primary Master UDMA [Auto] IDE Primary Slave UDMA [Auto] On-chip Secondary PCI IDE [Enabled] IDE Secondary Master PIO [Auto] IDE Secondary Slave PIO [Auto] IDE Secondary Master UDMA [Auto] IDE Secondary Slave UDMA [Auto] ATA 66/100 Cable Msg [Enabled]

*** On-Chip Serial ATA Setting***

SATA Mode [IDE] On-chip Serial ATA [Disabled] Serial ATA Port0 Mode [Primary Master]

Serial ATA Port1 Mode Primary Master

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

IDE HDD Block Mode (Enabled)

Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/write per sector the drive can support.

On-Chip Primary/Secondary PCI IDE (Enabled)

This integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel seperately.

Using BIOS

IDE Primary/Secondary Master/Slave PIO (Auto)

Each IDE channel supports a master device and a slave device. These four items let you assign the kind of PIO (Programmed Input/Output) was used by the IDE devices. Choose Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 0-4.

IDE Primary/Secondary Master/Slave UDMA (Auto)

Each IDE channel supports a master device and a slave device. This mainboard supports UltraDMA technology, which provides faster access to IDE devices. If you install a device that supports UltraDMA, change the appropriate item on this list to Auto. You may have to install the UltraDMA driver supplied with this mainboard in order to use an UltraDMA device.

ATA 66/100 Cable Msg (Enabled)

This item enalbes or disabled the display of the ATA 66/100 Cable Msg. If you install a device that supports UDMA, change the appropriate item on this list to Auto. You may have to install the UDMA driver supplied with this motherboard in order to use an UDMA device.

SATA Mode (IDE)

Use this item to select the mode of the Serial ATA.

On-Chip Serial ATA (Disabled)

Enables or disables the built-in on-chip Serial ATA.

Serial ATA Port0/Port1 Mode (Primary Master)

Use this item to select the SATA0 master or SATA1 master.

Press <Esc> to return to the Integrated Peripherals screen.

fOnboard Device

Scroll to this item and press <Enter> to view the following screen:

Phoenix-AwardBIOS CMOS Setup Utility Onboard Device

USB Controller [Enabled] USB 2.0 Controller [Enabled] USB Keyboard Support [Enabled] USB Mou se Support [Enabled] AC97 AUDIO [Auto] Onboard LAN Device [Enabled] Onboard LAN Boot ROM [Disabled]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

USB Controller (Enabled)

This item enables the USB controller. Leave this at the default “Enabled” if you want to connect USB devices to your computer.

USB 2.0 Controller (Enabled)

Enable this item if want to use the USB 2.0.

Using BIOS

USB Keyboard Support (Enabled)

This item allows the BIOS to interact with a USB keyboard or mouse to work with MS-DOS based utilities and non-Windows modes.

USB Mouse Support (Enabled)

Enable this item if you plan to use a mouse connected through the USB port in a legacy operating system (such as DOS) that does not support Plug and Play.

AC97 AUDIO (Enabled)

This option allows you to control the onboard AC97 audio. Disable this item if you are going to install a PCI audio add-on card.

Onboard LAN Device (Enabled)

This option allows you to enable or disable the onboard LAN.

Onboard LAN Boot ROM (Disabled)

Use this item to enable and disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed.

Press <Esc> to return to the Integrated Peripherals screen.

fSuperIO Device

Scroll to this item and press <Enter> to view the following screen:

Phoenix-AwardBIOS CMOS Setup Utility SuperIO Device

POWER ON Function [Hot Key] KB Power ON Password [Enter] Hot key Power ON [Ctrl-F12] Onboard FDC Controller [Enabled] Onboard Serial Port1 [3F8/IRQ4] Onboard Parallel Port [378/IRQ7] Parallel Port Mode [ECP] ECP Mode Use DMA [3] Power On After Power Fail [Off]

Item Help

Menu Level

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

POWER ON Function (Hot Key)

This feature allows you to set the method by which your system can be turned on.

KB Power ON Password (Enter)

When the POWER ON Function is set to Password, use this item to set the passowrd.

Hot Key Power On (Ctrl-F12)

When the POWER ON Function is set to Hot Key, use this item to set the hot key combination that turns on the system.

Using BIOS

Onboard FDC Controller (Enabled)

Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field.

Onboard Serial Port1 (3F8/IRQ4)

This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial port1 (COM1).

Onboard Parallel Port (378/IRQ7)

This option is used to assign the I/O address and interrupt request (IRQ) for the onboard parallel port.

Parallel Port Mode (ECP)

Enables you to set the data transfer protocol for your parallel port. There are four options: SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities Port), and ECP+EPP.

SPP allows data output only. Extended Capabilities Port (ECP) and Enhanced Parallel Port (EPP) are bi-directional modes, allowing both data input and output. ECP and EPP modes are only supported with EPP- and ECP-aware peripherals.

ECP Mode Use DMA (3)

When the onboard parallel port is set tp ECP mode, the parallel port can use DMA3 or DMA1.

Power On After Power Fail (Off)

This item enables your computer to automatically restart or return to its last operating status after power returns from a power failure.

Press <Esc> to return to the Integrated Peripherals screen.

Using BIOS

Power Management Setup

This option lets you control system power management. The system has various powersaving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be automatically resumed by certain events.

The power-saving modes can be controlled by timeouts. If the system is inactive for a time, the timeouts begin counting. If the inactivity continues so that the timeout period elapses, the system enters a power-saving mode. If any item in the list of Reload Global Timer Events is Enabled, then any activity on that item will reset the timeout counters to zero.

If the system is suspended or has been powered down by software, it can be resumed by a wake up call that is generated by incoming traffic to a modem, a LAN card, a PCI card, or a fixed alarm on the system realtime clock

Phoenix-AwardBIOS CMOS Setup Utility Power Management Setup

ACPI Suspend Type [S3 (STR)] Run VGABIOS if S3 Resume [Auto] Video Off Method [DPMS] Video Off In Suspend [Yes] Suspend Type [Stop Grant] Modem Use IRQ [3] Suspend Mode [Disabled] HDD Power Down [Disabled] Soft-Off by PWR-BTTN [Instant-Off] Resume by PCI PME [Enabled] Resume by Ring [Disabled] Resume by USB (S3) [Disabled] Resume by Alarm [Disabled]

Date (of Month) Alarm 0

Time (hh:mm:ss) Alarm 0 0 0

** Reload Global Timer Evernts **

Primary IDE 0 [Disabled] Primary IDE 1 [Disabled]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

ACPI Suspend Type (S3(STR))

Use this item to define how your system suspends. In the default, S1 (POS), the suspend mode is equivalent to a software power down. If you select S3 (STR), the suspend mode is suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the system memory.

Run VGABIOS if S3 Resume (Auto)

Use this item to initialize the VGA BIOS from S3 (Suspend to RAM) sleep state.

Video Off Method (DPMS)

This item defines how the video is powered down to save power. This item is set to DPMS (Display Power Management Software) by default.

Video Off In Suspend (Yes)

This option defines if the video is powered down when the system is put into suspend mode.

Using BIOS

Suspend Type (Stop Grant)

If this item is set to the default Stop Grant, the CPU will go into Idle Mode during power saving mode.

MODEM Use IRQ (AUTO)

If you want an incoming call on a modem to automatically resume the system from a power-saving mode, use this item to specify the interrupt request line (IRQ) that is used by the modem. You might have to connect the fax/modem to the motherboard Wake On Modem connector for this feature to work.

Suspend Mode (Disabled)

The CPU clock will be stopped and the video signal will be suspended if no Power Management events occur for a specified length of time. Full power function will return when a Power Management event is detected. Options are from 1 Min to 1 Hour and Disabled.

HDD Power Down (Disabled)

The IDE hard drive will spin down if it is not accessed within a specified length of time. Options are from 1 Min to 15 Min and Disable.

Soft-Off by PWR-BTTN (Instant-Off)

Under ACPI (Advanced Configuration and Power management Interface) you can create a software power down. In a software power down, the system can be resumed by Wake Up Alarms. This item lets you install a software power down that is controlled by the power button on your system. If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec. then you have to hold the power button down for four seconds to cause a software power down.

Resume by PCI PME (Enabled)

This item specifies whether the system will be awakened from power saving modes when activity or input signal of the specified hardware peripheral or component is detected.

Resume by Ring (Disabled)

An input signal on the serial Ring indicator (RI) line (in other words, and incoming call on the modem) awakens the system from a soft off state.

Resume by USB (S3)

This option allows the activity of the USB devices (keyboard and mouse) to wake-up the system from S3 sleep state.

Resume by Alarm (Disabled)

When set to Enabled, additional fields become available and you can set the date (day of the month), hour, minute and second to turn on your system. When set to 0 (zero) for the day of the month, the alarm will power on your system every day at the specified time.

** Reload Global Timer Events **

This field indicates which events waken the system from power saving mode.

Primary/Secondary IDE (Disabled)

When this item is enabled, the system power will resume the system from a power saving mode if there is any activity on primary or secondary IDE channel 0 or 1.

Using BIOS

PNP/PCI Configurations

This section describes configuring the PCI bus system. PCI (Peripheral Component Interconnect) is a system, which allows I/O devices to operate at speeds nearing CPU’s when they communicate with own special components. All the options describes in this section are important and technical and it is strongly recommended that only experienced users should make any changes to the default settings.

Phoenix-AwardBIOS CMOS Setup Utility PnP/PCI Configurations

Item Help

Reset Configuration Data [Disabled] Resources Controlled By [Auto(ESCD)]

IRQ Resources Press Enter

PCI/VGA Palette Snoop [Disabled] Assign IRQ For USB [Enabled] INT Pin 1 Assignment [Auto] INT Pin 2 Assignment [Auto] INT Pin 3 Assignment [Auto] INT Pin 4 Assignment [Auto] INT Pin 5 Assignment [Auto] INT Pin 6 Assignment [Auto] INT Pin 7 Assignment [Auto] INT Pin 8 Assignment [Auto]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Reset Configuration Data (Disabled)

When you enable this item and restart the system, any Plug and Play configuration data stored in the BIOS Setup is cleared from memory.

Resources Controlled By (Auto(ECSD))

You should leave this item at the default Auto(ESCD). Under this setting, the system dynamically allocates resources to Plug and Play devices as they are required. If you cannot get a legacy ISA (Industry Standard Architecture) expansion card to work properly, you might be able to solve the problem by changing this item to Manual, and then opening up the IRQ Resources submenu.

In the IRQ Resources submenu, if you assign an IRQ to Legacy ISA, then that

•

Interrupt Request Line is reserved for a legacy ISA expansion card. Press <Esc> to close the IRQ Resources submenu.

PCI/VGA Palette Snoop (Disabled)

This item is designed to overcome problems that can be caused by some non-standard VGA cards. This board includes a built-in VGA system that does not require palette snooping so you must leave this item disabled.

Assign IRQ For USB (Enabled)

“Enable” or “Disable” this item when users are to assign IRQ for the USB interface onboard.

INT Pin1~8 Assignment (Auto)

Identifies the interrupt request (IRQ) line assigned to a device connected to the PCI interface of your system.

Menu Level

Default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the OS cannot boot

Using BIOS

PC Health Status

On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds.

Phoenix-AwardBIOS CMOS Setup Utility PC Health Status

Target Temperature [Disabled] Shutdown Temperature [Disabled] Case Open Warning [Disabled]

Case has been: [Closing] Current System Temperature Current CPU Temperature SYS FAN Speed CPU FAN Speed PWR FAN Speed CPU Vcore

1.50 V

3.30V

5.00 V Battery Voltage

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

Target Temperature (Disabled)

This item enables throttling when CPU targets the temperature.

Shutdown Temperature (Disabled)

Enables you to set the maximum temperature the system can reach before powering down.

System Component Characteristics

These items allow end users and technicians to monitor data provided by the BIOS on this motherboard. You cannot make changes to these fields.

• Current CPU/System Temperature

• CPU Fan Speed

• CPU Core Voltage

• Battery Voltage

Using BIOS

Frequency Control

This item enables you to set the clock speed and system bus for your system. The clock speed and system bus are determined by the kind of processor you have installed in your system.

Phoenix-AwardBIOS CMOS Setup Utility Frequency Control

CPU Clock Ratio [8X] Auto Detect PCI Clk [Enabled] Spread Spectrum [Enabled] Async AGP/PCI CLK [Disabled] CPU Clock [100MHz]

: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help

mnlk

F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Item Help

Menu Level

CPU Clock Ratio (8X)

Enables you to set the CPU clock. The CPU clock ratio times the CPU Host/PCI Clock should equal the core speed of the installed processor. (For unlock Ratio CPU only.)

Example: CPU Clock Ratio 8

CPU Frequency X100 Installed CPU Clock Speed 800 MHz

Auto Detect DIMM/PCI Clk (Enabled)

When this item is enabled, BIOS will disable the clock signal of free DIMM and PCI slots.

Spread Spectrum (Enabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

Async AGP/PCI CLK (Disabled)

This item allows you to select the fixed clock to generate the output to AGP/PCI frequency.

CPU Clock (100MHz)

Use the CPU Host Clock to set the frontside bus frequency for the installed processor (usually 133 MHz, 100 MHz, or 66 MHz).

Using BIOS

Load Performance Defaults

This option opens a dialog box that lets you install performance defaults for all appropriate items in the Setup Utility:

Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The performance defaults place no great demands on the system and are generally stable. If your system is not functioning correctly, try installing the performance defaults as a first step in getting your system working properly again. If you only want to install performance defaults for a specific option, select and display that option, and then press <F6>.

Load Optimized Defaults

This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The optimized defaults place demands on the system that may be greater than the performance level of the components, such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults when your hardware does not support them. If you only want to install setup defaults for a specific option, select and display that option, and then press <F7>.

Set Supervisor/User Password

When this function is selected, the following message appears at the center of the screen to assist you in creating a password.

ENTER PASSWORD

Type the password, up to eight characters, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection.

To disable password, just press <Enter> when you are prompted to enter password. A message will confirm the password being disabled. Once the password is disabled, the system will boot and you can enter BIOS Setup freely.

PASSWORD DISABLED

If you have selected “System” in “Security Option” of “BIOS Features Setup” menu, you will be prompted for the password every time the system reboots or any time you try to enter BIOS Setup.

If you have selected “Setup” at “Security Option” from “BIOS Features Setup” menu, you will be prompted for the password only when you enter BIOS Setup.

Supervisor Password has higher priority than User Password. You can use Supervisor Password when booting the system or entering BIOS Setup to modify all settings. Also you can use User Password when booting the system or entering BIOS Setup but can not modify any setting if Supervisor Password is enabled.

Using BIOS

Save & Exit Setup Option

Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <Y> to save and exit, or press <N> to return to the main menu:

Exit Without Saving

Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, press <Y> to discard changes and exit, or press <N> to return to the main menu.

If you have made settings that you do not want to save, use the “Exit Without Saving” item and press <Y> to discard any changes you have made.

This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard.

Using BIOS

Memo

Using BIOS

Chapter 4

Using the Motherboard Software

About the Software CD-ROM

The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software.

Never try to install all software from folfer that is not specified for use with your motherboard.

Before installing any software, always inspect the folder for files named README.TXT, INSTALL.TXT, or something similar. These files may contain important information that is not included in this manual.

Auto-installing under Windows 98/ME/2000/XP

The Auto-install CD-ROM makes it easy for you to install the drivers and software for your motherboard.

If the Auto-install CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.

The support software CD-ROM disc loads automatically under Windows 98/ME/2000/XP. When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.

If the opening screen does not appear; double-click the file “setup.exe” in the root directory.

Using the Motherboard Software

Setup Tab

Setup

Browse CD

Exit The EXIT button closes the Auto Setup window.

Application Tab

Lists the software utilities that are available on the CD.

Read Me Tab

Displays the path for all software and drivers available on the CD.

Click the Setup button to run the software installation program. Select from the menu which software you want to install.

The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD.

Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly.

Some software is installed in separate folders for different operating systems.

In install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen.

Running Setup

Follow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

4. Click Next run the Installation Wizard. An item installation screen appears:

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Using the Motherboard Software

Manual Installation

Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior notice. Please refer to the support CD for available software.

AMI/AWARD Flash Utility

This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard, and lets you copy an updated version of the BIOS to the chip. Proceed with caution when using this program. If you erase the current BIOS and fail to write a new BIOS, or write a new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for more information.

WinFlash Utility

The WinFlash utility is a Windows version of the DOS BIOS flash writer utility. The utility enables you to flash the system BIOS stored on a Flash Memory chip on the motherboard while in a Windows environment. This utility is currently available for WINXP\ME\2000\98SE. To install the WinFlash utility, run AFUWIN.EXE(AMI) or WINFLASH.EXE(Award) from the following directory:\UTILITY\WINFLASH AMI or Award.

This concludes Chapter 4.

Using the Motherboard Software

Caractéristiques

Processeur

Cette carte mère utilise un type LGA775 de Pentium 4/Celeron D/Pentium D présentant les fonctionnalités suivantes :

• Reçoit des processeurs Intel Pentium 4/Celeron D/Pentium D

• Support un bus système (FSB) de 800/533 MHz

• Supporte le CPU de technologie “Hyper-Threading”

La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est connecté à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des processeurs ‘logiques’ dans le même processeur physique.

Chipset

Le chipset 848P Northbridge (NB) Chipset et ICH5 Southbridge (SB) se base sur une architecture innovante et évolutive avec des performances et une ﬁabilité éprouvées.

848P (NB)

• Prend en charge l’interface Hub (HI) 1.5 avec la connexion point à point de 266 Mo/s vers ICH5

• Prend en charge AGP 3.0 avec transferts de données AGP 8X/4X et fast writes 8X/4X respectivement

• Prend en charge l’interface mémoire DDR à canal simple & canal double

• Prend en charge les modules DIMM DDR400/333/266

• Prend en charge jusqu’à deux DIMM sans mémoire tampon avec une taille maximum de 2 Go

Français

ICH5 (SB)

• Prend en charge jusqu’à six Maîtres PCI entièrement conformes aux spéciﬁcations PCI 2.3 à 33MHz.

• Prend en charge 2 Contrôleurs IDE de Maître Bus à canaux Ultra ATA 100

• El controlador SATA soporta dos dispositivos SATA

• Conforme à AC’97 v2.3 prenant en charge 6 Canaux de sorties audio

• Huit Ports USB 2.0 pour les transferts en série en 480Mb/Sec Max.

Mémoire

• Supporte le module mémoire DDR SDRAM DDR400/333/266

• Reçoit deux DIMM sans tampon

• Jusqu’à 1 Go par DIMM avec une taille de mémoire maximum de 2 Go

Audio

• Conforme aux spéciﬁcations AC’97 2.3

• Prend en charge le CODEC audio 6 canaux destiné aux systèmes multimédia PC

• Offre trois entrées stéréo de niveau de ligne analogique avec contrôle de volume 5 bits: Ligne d’entrée, CD, AUX

• Conforme aux exigences audio de Microsoft WHQL/WLP 2.0

Multi-Language Translation

Français

LAN sur carte (optionnel)

Cette carte mère prend en charge les chipsets LAN suivants :

Options d’extension

La carte mère comporte les options d’extension suivantes :

La carte mère prenant en charge la maîtrise de bus UltraDMA avec vitesses de transfert de 100/66 Mo/s.

E/S intégrées

La carte mère comporte un ensemble complet de connecteurs et de ports E/S :

• Supporte le fonctionnement en Auto-négociation N-way en 10/100 Mb/s

• Prend en charge la capacite half/full duplex

• Supporte la fonction Wake-On-LAN (WOL) -réveil par appel réseau et le réveil à distance

• Emetteur-récepteur 1000/100/10 intégré

• Prend en charge PCI v2.3, 32 bits, 33/66-MHz

• Prise en charge totale avec IEEE 802.3, IEEE 802.3u et IEEE 802.3ab

• Un slot compatible AGP 3.0 avec vitesse 8X/4X(supporte la carte 1.5V AGP seulement)

• Cinq slots conforme PCI v2.2 32 bits

• Deux en-têtes demi-hauteur IDE de 40 broches supportant quatre canaux IDE

• Une interface de lecteur de disquette

• Deux connecteurs SATA à 7 broches

• Deux ports PS/2 pour souris et clavier

• Un port série

• Un port parallèle

• Quatre ports USB

• Un port LAN (optionnel)

• Prises audio pour microphone, ligne d’entrée et ligne de sortie

Microprogramme BIOS

Cette carte mère utilise Award BIOS qui permet aux utilisateurs de conﬁgurer de nombreuses caractéristiques du système comprenant les suivantes:

• Gestion d’alimentation

• Alarmes de réveil

• Paramètres de CPU

• Synchronisation de CPU et de mémoire

Le micro-programme peut également être utilisé pour déﬁnir les paramètres pour différentes vitesses d’horloge de processeur.

Certaines spéciﬁcations matérielles et certains éléments logiciels sont suscep tibles de modiﬁcation sans préavis.

Multi-Language Translation

Feature

Prozessor

Das Motherboard verwendet einen LGA775 Typ Pentium 4 folgenden Eigenschaften:

• Nimmt Intel Pentium 4/Celeron D/Pentium D Prozessoren auf

• Unterstützt einen Systembus (FSB) mit 800/533 MHz

• Unterstützt CPU mit “Hyper-Threading”-Technologie

“Hyper-Threading”-Technologie läßt das Betriebssystem glauben, es sei an zwei Prozessoren angeschlossen, was zwei parallele Threads auf separaten ‘logischen’ Prozessoren im selben physischen Prozessor erlaubt.

/Celeron D/Pentium D mit den

Chipsatz

Die 848P Northbridge (NB) und ICH5 Southbridge (SB) basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung.

848P (NB)

• Unterstützt Hub-Schnittstelle (HI) 1.5 mit 266 MB/s Punkt-zuPunkt Verbindung zu ICH5

• Unterstützt AGP 3.0 mit 8X/4X AGP Datenübertragung und 8X/4X schnelles Schreiben

• Unterstützt Single-Channel DDR Speicherschnittstellen

• Unterstützt DDR400/333/266 DIMM Module

• Unterstützt bis zu 2 ungepufferte DIMMs für bis zu 2 GB Systemspeicher.

Deutsche

ICH5 (SB)

• Unterstützt bis zu sechs PCI Steckplätze, die der PCI 2.3 Speziﬁkation mit 33 MHz entsprechen.

• Unterstützt 2 Känäle Ultra ATA 100 Bus Master IDE-Controller

• Der SATA-Controller unterstützt zwei SATA-Geräte

• Entspricht AC’97 v2.3 und unterstützt 6 Kanal Audioausgänge

• Acht USB 2.0 Ports für seriellen Datentransfer mit max. 480 Mb/Sek.

Speicher

• Unterstützt DDR SDRAM bis zu DDR400/333/266 Speichermodul

• Es können zwei ungepufferte DIMMs aufgenommen werden.

• Bis zu 1 GB pro DIMM mit maximaler Speicherkapazität von bis zu 2 GB.

Audio

• Entspricht AC’97 2.3 Speziﬁkationen

• Unterstützt 6-Kanal Audio CODEC, entwickelt für Multimedia PC-Systeme

• Stellt drei analoge Line-Level Stereoeingänge mit 5-bit Lautstärkeregelung zur Verfügung: Line-in, CD, AUX

• Entspricht den Microsoft WHQL/WLP 2.0 Audio-Anforderungen

Multi-Language Translation

Deutsche

Onboard LAN (Optional)

Dieses Motherboard kann einen der folgenden LAN-Chipsätze unterstützen:

• Unterstützt 10/100 Mb/Sek N-way Auto-negotiation Betrieb

• Unterstützt Halb-/Vollduplex

• Unterstützt Wake-On-LAN (WOL) Funktion und Remote Wake-up

• Enthält 1000/100/10 Transceiver

• Unterstützung von PCI v2.3, 32-Bit, 33/66-MHz

• Volle Unterstützung mit IEEE 802.3, IEEE 802.3u und IEEE 802.3ab

Erweiterungs-optionen

La carte mère comporte les options d’extension suivantes :

• Einen AGP 3.0 Steckplatz, gemäß Sockel mit 8x/4x Geschwindigkeit (unterstützt nur 1.5V AGP Interface)

• Fünf 32-bit PCI-Steckplätze

• Zwei 40-Pin IDE low proﬁle-Stecker, die vier IDE-Kanäle unterstützen

• Eine Schnittstelle für ein Floppydiskettenlaufwerk

• Zwei 7-Pin SATA Anschlüsse

Dieses Motherboard unterstützt UltraDMA Bus Mastering mit einer Übertragungsrate von 100/66 MB/Sek.

Integrierte I/O

Das Motherboard verfügt über einen kompletten Satz von I/O- Schnittstellen und Anschlüssen:

• Zwei PS/2-Ports für Maus und Tastatur

• Eine serielle Schnittstelle

• Eine parallele Schnittstelle

• Vier USB-Schnittstellen

• Eine LAN-Schnittstelle (optional)

• Audiobuchsen für Mikrofon, Line-in und Line-out

BIOS-Firmware

Das Motherboard verwendet Award BIOS, das es Benutzern gestattet, viele Systemfunktionen inkl. der Folgenden zu konﬁgurieren:

• Energieverwaltung

• Aufweckfunktionen

• CPU-Parameter

• CPU- und Arbeitsspeicherfrequenz

Die Firmware kann auch zur Einstellung von Parametern für verschiedene Prozessortaktge schwindigkeiten verwendet werden.

Manche Hardwarespeziﬁkationen und Softwareelemente können ohne Ankün digung geändert werden.

Multi-Language Translation

Caratteristiche

Processore

La scheda madre utilizza un tipo LGA775 di Pentium 4/Celeron D/Pentium D che offre le seguenti caratteristiche:

• Alloggia processori Intel Pentium 4/Celeron D/Pentium D

• Supporta un bus di sistema (FSB) ﬁno a 800/533 Mhz

• Supporta CPU con tecnologia “Hyper-Threading”

La tecnologia “Hyper-Threading” induce il sistema operativo a pensare di essere collegato a due processori, questo permette di eseguire due thread in parallelo, ambedue su processori “logicamente” separati all’interno dello stesso processore.

Chipset

I chipset 848P Northbridge (NB) e ICH5 Southbridge (SB) sono basati su una architettura innovativa e scalabile dalle prestazioni e afﬁdabilità garantite.

848P (NB)

• Supporto di Hub Interface (HI) 1.5 con collegamento point to point a 266 MB/s a ICH5

• Supporto di AGP 3.0 con trasferimento di dati AGP a 8X/4X e scrittura rapida a 8X/4X

• Supporto di interfaccia memoria DDR Single Channel

• Supporto di moduli DIMM con DDR 400/333/266

• Supporto di ﬁno a 2 DIMM senza buffer con una capacita massima di memoria di 2 GB

Italiano

ICH5 (SB)

• Supporto di ﬁno a sei master PCI a 33 MHz pienamente compatibili con la speciﬁca PCI 2.3

• Supporto di controller IDE Bus Master Ultra ATA 100 a 2 canali

• Il controller SATA supporta due dispositivi SATA

• Conforme alla speciﬁca AC’97 v2.3 con supporto di 6 canali audio in uscita

• Otto porte USB 2.0 per trasferimenti seriali a velocità di 480Mb/ sec Max

Memoria

• Supporta un modulo di memoria SDRAM DDR con a DDR 400/333/266

• Alloggia 2 DIMM unbuffered

• Fino a 1 GB per ciascun DIMM con una capacità massima di memoria di 2 GB

Audio

• Conforme alle speciﬁche AC’97 2.3

• Supporto di CODEC audio a 6 canali per sistemi PC multimediali

• Tre ingressi analogici stereo lineari con controllo volume a 5 bit: Line-In, CD, AUX

• Conforme ai requisiti audio di WHQL e WLP 2.0 di Microsoft

Multi-Language Translation

LAN Onboard (opzionale)

La funzionalità LAN integrata sulla scheda offre le seguenti caratteristiche:

Italiano

Opzioni di espansione

La carte mère comporte les options d’extension suivantes :

La scheda madre supporta bus master UltraDMA con tasso di trasferimento di 100/66 MB/s.

I/O integrato

La scheda madre è dotata di un set completo di connettori e porte I/O:

• Supporta operazioni di auto-negoziazione N-way a 10/100 Mb/s

• Supporto di funzionalità half/full duplex

• Supporto funzione WOL (Wake-On-LAN) e wake up remoto

• Transceiver 1000/100/10 integrato

• Supporta PCI v2.3, 32-bit, 33/66-MHz

• Completamente conforme con l’IEEE 802.3, IEEE 802.3u e IEEE

802.3ab

• Uno slot AGP 3.0 8X/4X(supporta solo l’interfaccia 1.5V AGP)

• Cinque slot PCI v2.3 a 32 bit

• Due connettori IDE a 40 pin che supportano quattro canali IDE

• Una interfaccia ﬂoppy disk

• Due connettori SATA a 7 pin.

• Due porte PS/2 per mouse e tastiera

• Una porta seriale

• Una porta parallela

• Quattro porte USB

• Una porta LAN (opzionale)

• Jack audio per microfono, linea d’ingresso e linea d’uscita

Firmware BIOS

Questa scheda madre adotto un BIOS Award che permette agli utenti di conﬁgurare le caratteristiche principali del sistema, inclusi::

• Gestione energia

• Allarmi wake up

• Parametri CPU

• Temporizzazione CPU e memoria

Il ﬁrmware può anche essere usato per impostare i parametri per diverse velocità di clock.

Alcune speciﬁche hardware e software potrebbero essere soggette a cambiamenti senza preavviso.

Multi-Language Translation

Características

Procesador

Esta placa principal usa un tipo LGA775 de Pentium 4/Celeron D/Pentium D que lleva las sigtes. características:

• Acomoda procesadores Intel Pentium 4/Celeron D/Pentium D

• Soporta un sistema de bus (FSB) de 800/533 MHz

• Soporta CPU de tecnología “Hyper-Threading”

La tecnología “Hyper-Threading” habilita el sistema operativo para que piense como si estuviera conectado a dos procesadores, que permite dos hilos a correr en paralelo, ambos en procesadores “lógicos” dentro del mismo procesador físico.

Chipset

Los chipsets Northbridge 848P (NB) y Southbridge ICH5(SB) están basados en una arquitectura innovadora y escalable con ﬁabilidad y rendimiento comprobados.

848P (NB)

ICH5 (SB)

• Soporta la Interfaz Hub (HI) 1.5 con conexión punto a punto de 266 MB/s a ICH5

• Soporta AGP 3.0 con transferencias de datos 8X/4X AGP y escrituras rápidas 8X/4X respectivamente

• Soporta interfaz de memoria DDR de Single-channel (Canal Singular )

• Soporta módulos DIMM de DDR400/333/266

• Soporta hasta dos DIMM sin buffer con un tamaño de memoria máxima de 2 GB.

• Soporta hasta seis PCI Masters completamente conforme con la especiﬁcación PCI 2.3 en 33 MHz

• Soporta controladores IDE de máster bus de Ultra ATA 100 de 2 canales

• El controlador SATA soporta dos dispositivos SATA

• Conforme con AC’97 v2.3 que soporta 6 Canales de salidas de sonido

• Ocho Puertos USB 2.0 para transferencias seriales en 480Mb/ seg Máx

Español

Memoria

• Soporta hasta módulo de memoria DDR400/333/266 DDRSDRAM

• Acomoda dos DIMMS sin buffer

• Hasta 1 GB por DIMM con tamaño de memoria máxima hasta 2 GB

Audio

• Conformidad con las CODEC AC’97 2.3

• Soporta CODEC de audio de 6 canales diseñaods para los sistemas multimedia

• Provee tres entradas en estéreo a nivel de línea análogicas con control de volumen de 5-bit: LIne-in, CD, AUX

• Satisface los requisitos de audio de Microsoft WHQL/WLP 2.0

Multi-Language Translation

LAN abordo(optativo)

Esta placa principal puede soportar uno de los sigtes. chipset LAN:

Español

Opciones de Expansión

La placa principla viene con las sigtes. opciones de expansión:

La placa principal soporta el mastering de bus UltraDMA con índices de transferencia de 100/66 MB/s.

I/O Integrado

La placa principal tiene un juego completo de puertos y conectores I/O:

• Soporta la operación de auto-negociación de 10/100 Mb/s N-way

• Soporta capacidad duplex medio/completo

• Soporta la función Wake-On-LAN (WOL) y despertar remoto

• Transceptor 1000/100/10 integrado

• Soporta PCI v2.3, 32-bit, 33/66-MHz

• Soporte completo con el IEEE 802.3, IEEE 802.3u y IEEE 802.3ab

• Una ranura conforme con AGP 3.0 con la velocidad 8X/4X (soporta interfaz

1.5V AGP solamente)

• Cinco ranuras conforme con 32-bit PCI v2.3

• Dos cabezales de perﬁl bajo 40-pin IDE que soporta cuatro canales IDE

• Una interfaz de lector de ﬂoppy

• Dos conectores 7-pin SATA

• Dos puertos PS/2 para ratón y teclado

• Un puerto seriales

• Un puerto paralelo

• Cuatro puertos USB

• Un puerto LAN (optativo)

• Clavijas de sonido para micrófono, entrada y salida de línea

BIOS Firmware

La placa principal usa Award BIOS que habilita a los usuarios para que conﬁguren muchas características del sistema incluyendo las siguientes:

• Administración de alimentación

• Alarmas despertadores

• Parámetros de CPU

• Cronometraje de CPU y de memoria

También se puede usar el ﬁrmware para conﬁgurar los parámetros para diferentes velocidades de reloj del procesador.

Algunas especiﬁcaciones de hardware e ítems de software son sujetos a cambio sin aviso previo.

Multi-Language Translation

Características

Procesador

Esta motherboard usa um tipo de Pentium 4/Celeron D/Pentium D LGA775 que possui as seguintes características:

• Acomoda processadores Intel Pentium 4/Celeron D/Pentium D

• Suporta um bus sistema (FSB) de 800/533 MHz

• Suporta CPU de tecnologia “Hyper-Threading”

A tecnologia “Hyper-Threading” permite que o sistema operativo “pense” que está ligado a dois processadores, permitindo que sejam executados dois threads em paralelo, ambos em processadores “lógicos” separados dentro do mesmo processador físico.

Chipset

O 848P Northbridge (NB) e o ICH5 Southbridge (SB) baseia-se numa inovadora arquitectura escalável, com conﬁança e desempenho comprovados.

848P (NB) • Suporta um Interface Hub (HI) 1.5 com ligação ponto a

ponto de 266 MB/s ao ICH5

• Suporta AGP 3.0 com transferências de dados de 8X/4X AGP e escritas rápidas 8X/4X respectivamente

• Suporta interface de memória DDR Bicanal

• Suporta módulos DDR400/333/266 DIMM

• Suporta até dois DIMMs sem buffers com capacidade máxima de memória de 2 GB

Português

ICH5 (SB)

• Suporta até seis PCI Masters que cumprem totalmente com a especiﬁcação PCI 2.3 a 33 MHz

• Suporta controladores IDE master bus 100 ATA Ultra com 2 canais

• O controlador SATA suporta dois dispositivos SATA

• Cumpre com a especiﬁcação AC’97 v2.3 suportando 6 Canais de saídas áudio

• Suporta oito portas USB 2.0 para transferências de série a um máximo de 480Mb/s

Memoria

• Suporta o módulo de memória DDR400/333/266 DDR SDRAM

• Acomoda dois DIMMs sem buffers

• Até 1 GB por DIMM com capacidade máxima de memória até 2 GB

Áudio

• Cumpre com as especiﬁcações AC’97 2.3

• Suporta CODEC áudio com 6 canais concebido para sistemas multimédia para PC

• Fornece três entradas estéreo nível de linha analógicas com controlo de volume de 5 bits: LIne-in, CD, AUX

• Cumpre com os requisitos áudio WHQL/WLP 2.0 da Microsoft audio

Multi-Language Translation

LAN incorporada (Opcional)

Esta motherboard poderá suportar qualquer um dos seguintes conjuntos de chips LAN:

• Suporta o funcionamento de negociação automática de 10/100 Mb/s N-

direcções

• Suporta capacidade de duplex pela metade/ou na totalidade

• Suporta a função Wake-On-LAN(WOL) e despertar remoto

• Transreceptor integrado 1000/100/10

• Suporta PCI v2.3, 32-bit, 33/66-MHz

• Suporta inteiramente com IEEE 802.3, IEEE 802.3u e IEEE 802.3ab

Português

Opções de Expansão

A placa principal vem equipada com as seguintes opções de expansão:

• Uma ranhura compatível com AGP 3.0 com uma velocidade de 8X/4X (suporta apenas 1.5V AGP)

• Cinco ranhuras compatíveis com PCI v2.3 de 32 bits

• Dois cabeçalhos de baixo perﬁl IDE 40 pinos, que suportam quatro disposi-

tivos IDE

• Uma interface da unidade de disquete

• Dois conectores SATA de 7 pinos

A motherboard suporta um domínio bus UltraDMA bus com taxas de Transferência de 100/66 MB/s.

E/S integrado

A placa principal conta com um conjunto completo de portas e conectores E/S:

• Duas portas PS/2 para o rato e o teclado

• Uma porta de série

• Uma porta paralela

• Quatro portas USB

• Uma porta LAN (opcional)

• Tomadas de áudio para microfone, linha de entrada e linha de saída

BIOS Firmware

Esta placa principal utiliza a Award BIOS que permite aos utilizadores conﬁgurarem muitas funções do sistema, incluindo as seguintes:

• Gestão de energia

• Alarmes de despertar

• Parâmetros da UCP

• Temporização da UCP e da memória

O ﬁrmware também pode ser utilizado para deﬁnir parâmetros para diferentes velocidades do relógio do processador

Algumas especiﬁcações de hardware e itens de software estão sujeitos a alteração sem aviso prévio.

Multi-Language Translation

機能

プロセッサ

このマザーボードには LGA775 タイプのPentium 4/Celeron D/Pentium D を取り付け可能で、次の特徴があります：

• Intel Pentium 4/Celeron D/Pentium D プロセッサに対応

• 800/533 MHzのシステムバス(FSB)をサポート

• “ハイパースレッド” 技術をサポート

ハイパースレッド（HT）技術というのは、オペレーションシステムに2つのプロセッサが存在すると認識させることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ、平行利用を可能とする技術

です。

チップセット

搭載した848P Northbridgeおよび ICH5 Southbridgeチップセットは最新且つ拡張性あるアーキテクチャを採用し、高い安定性およびパフォーマンスを兼ね備えたものです。

848P (NB)

ICH5 (SB)

• ICH5に266MB／秒のポイント対ポイントの接続を可能にするHI

(Hub Interface) 1.5 に対応

• 8X/4X のAGPデータ転送と8X/4X の高速書き込みとの機能を持

つ AGP 3.0 に対応

• シングルチャネルのDDR メモリインターフェースに対応

• DDR400/333/266 DIMMモジュールに対応

• 2つの非バッファーDIMMで最大2 GB までのメモリの取り付けを可能

• 6つのPCI Masterに対応、33MHZではPCI 2.3 規格に完全準拠

• 2 チャネルのUltra ATA 100 バスマスタ IDE コントローラをサポ

ート

• SATAコントローラで2つまでのSATAデバイスをサポート可能

• 6つチャネルのオーディオ出力をサポートするAC’97 v2.3に準拠

• 最大480Mb/秒のシリアル転送率可能の8つのUSB2.0ポート

メモリ-

• DDR400 /333/266 のDDR SDRAMメモリモジュールに対応

• 2つの非バッファーDIMMを搭載

• 各DIMMに1 GB のメモリを、合計で2 GBを装着可能

オーディオ

• AC’97 2.3 規格に準拠

• ＰＣマルチメディアシステムの6チャネルオーディオＣＯＤＥＣをサポート

• 5ビット音声コントロール可能のアナログラインレベルのステレオ入力が3つ：ライ

ンイン、ＣＤ、およびＡＵＸ

• Microsoft WHQL/WLP 2.0 オーディオ要求に適合

日本語

Multi-Language Translation

日本語

オンボードLAN (オプション)

当マザーボードは次のLANチップセットのいずれかを搭載しております：

• 10/100 Mb/秒のNウェイ自動認識機能動作をサポート

• 半/全二重動作可能

• Wake-On-LAN (WOL) 機能とリモートwake-up機能

• 1000/100/10 トランシーバーを搭載済み

• PCI v2.3, 32-bit, 33/66-MHzへの対応

• IEEE 802.3、IEEE802.3u およびIEEE802.3abに完全対応

拡張オプション

このメインボードには次の拡張オプションがあります:

• 8X/4Xモード対応のAGP3.0仕様スロット(1.5VAGPインターフェースのみに対応

)が1つ。

• 32ビットPCIスロットが5つ

• 40ピンIDEロープロフィルヘッダー(4つのIDEチャネルをサポート)が2つ

• フロッピーディスクインターフェースが1つ

• 7ピンSATAコネクタが2つ

このマザーボードは、100/66 MB/秒の転送速度でのUltra DMAバスマスタリングをサポートします。

統合の入出力ポート

このメインボードはフルセットのI/Oポートおよびコネクタを搭載しています。それらは次の通りです：

• マウスとキーボード用のPS/2ポートが2つ

• シリアルポートが1つ

• パラレルポートが1つ

• USBポートが4つ

• LANポートが1つ (オプション)

• マイクロフォンやラインイン、ラインアウト用のオーディオジャック

BIOSファームウェア

本メインボードは次ぎのシステム機能を含めた設定をすることができるAward BIOSを採用しています：

• 電源管理

• Wake-up警告

• CPU パラメータ

• CPU およびメモリのタイミング

その他に、各種プロセッサクロック速度のパラメータを設定することができます。

一部のハードウェア仕様及びソフトウェアアイテムは予告なく変更されることがあります。

Multi-Language Translation

기능

프로세서

본 마더보드는 팬티엄 4/Celeron D/팬티엄 D 의 LGA775 을 사용하며 다음과 같은 특 성을 지닙니다:

• Intel 팬티엄 4/Celeron D/팬티엄 D 프로세서 사용

• 800/533 MHz시스템 버스(FSB) 지원

• ” Hyper-Threading ”기술 CPU 지원

”Hyper-Threading”기술은 운영체제를 두 개의 프로세서에 연결한 것처럼 두개의 트래드를 패러럴로 실행하여 같은 물리적 프로세서 안에서 각기 다른 “논리적” 프 로세서를 실행할 수 있게 한다.

칩셋

848P Northbridge (NB) 와 ICH5 Southbridge (SB) 칩셋은혁신적이고 범위성을 지닌 아키텍쳐를 바탕으로 인정된 신뢰성과 성능을 지닌다.

848P (NB)

ICH5 (SB)

• ICH5 에 266 MB/s 포인트 투 포인트 커넥션을 지원하는 허브 인터페이스 (HI) 1.5 지원

• 8X/4X AGP 데이터 전송 및 8X/4X 패스트 라이트를 지원하 는 AGP 3.0 지원

• 싱글 채널 채널 DDR 메모리 인터페이스 지원

• DDR400/333/266 DIMM 모듈 지원

• 최대 2 개의 unbuffered DIMM 지원. 최대 메모리 용량 2 GB.

• 33 MHz 에서 PCI 2.3 사양에 전적으로 부합하는 PCI 마스터

최대 6 개 지원

• SATA 컨트롤러는 2개의 SATA 장치를 지원합니다

• 2 개의 시리얼 ATA 호스트 컨트롤러 지원

• 오디오 출력 6 채널을 지원하는 AC’97 v2.3 부합

• 480Mb/sec 의 시리얼 전송을 위한 8 개의 USB 2.0 포트

메모리

• DDR 400/333/266 MHz DDR SDRAM 메모리 모듈 지원

• 2 개의 unbuffered DIMM 사용

• DIMM 당 최대 1 GB, 최대 메모리 크기 2 GB

오디오

• AC’97 2.3 사양 부합

• PC 멀티미디어 시스템을 위해 디자인 된 6 채널 오디오 코덱 지원

• 5 비트 볼륨 컨트롤의 아날로그 라인 레벨 스테레오 입력 3개 : Line-in, CD,

AUX

• 마이크로소프트 WHQL/WLP 2.0 오디오 요구 조건 부합

한국인

Multi-Language Translation

한국인

보드 내장 LAN (선택 사항)

본 마더보드는 다음과 같은 LAN 칩셋을 지원합니다:

• 10/100 Mb/s 자동 조정 오퍼레이션 지원

• Half/Full 듀플렉스 지원

• Wake-On-LAN (WOL) 기능 및 원격 wake-up 지원

• 통합 1000/100/10 트랜시버

• PCI v2.3, 32-bit, 33/66-MHz 지원

• IEEE 802.3, IEEE802.3u 및 IEEE802.3ab 지원

확장 옵션

이 메인보드는 다음과 같은 확장 옵션이 있다

• 8X/4X 속도의 AGP 3.0 호환 슬롯 1개(1.5V AGP 인터페이스만 지원)

• 32 비트 PCI v2.3 호환 슬롯 5 개

• 4 개의 IDE 채널을 지원하는 40 핀 IDE 로우 프로파일 해더 2 개

• 플로피 디스크 드라이브 인터페이스 1 개

• 7 핀 SATA 커넥터 2 개

마더보드는 전송 속도 100/66 MB/s의 UltraDMA 버스 마스터링을 지원한다.

통합 I/O

이 메인보드에는 풀 세트의 I/O 포트와 커넥터가 있다

• 마우스와 키보드용 PS/2 포트 2 개

• 시리얼 포트 1개

• 패러럴 포트 1 개

• USB 포트 4개

• LAN 포트 1 개 (선택 사항)

• 마이크용 오디 오 잭, line-in 과 line-out

BIOS 펌웨어

본 메인보드는 Award BIOS 를 사용하여 사용자는 다음과 같은 시스템 기능을

• 전원 관리

• Wake-up 알람

• CPU 파라미터

• CPU 및 메모리 타이밍

펌웨어는 다른 프로세서의 클럭 속도를 설정하는 데도 사용될 수 있다

하드웨어 사양 및 소프트웨어 아이템은 사전 통보없이 변경될 수 있습니다

Multi-Language Translation

規格

處理器

本主機板適用於LGA775 型Pentium 4 /Celeron D/Pentium D且具有如下功能：

• 支援Intel Pentium 4 /Celeron D/Pentium D處理器

• 支援高達800/533 MHz之系統匯流排(FSB)

• 支援使用"超執行緒(Hyper-Threading)"技術之CPU

利用“超執行緒(HT)＂技術，可使作業系統在相當於裝上了兩具處理器的狀態下運作：利用一個＂實體＂處理器模擬出兩個獨立的＂邏輯＂處理器，同時執行兩個工作緒。

晶片組

848P北橋(NB)及ICH5(SB)南橋晶片組，採用了獨創且具有擴充功能的架構，能夠發揮最佳的穩定性及功能。

848P (NB)

ICH5 (SB)

• 支援Hub Interface (HI) 1.5，提供對ICH5高達266 MB/秒的點對點連接

• 支援具有8X/4X AGP 資料傳輸及8X/4X 快寫功能的AGP 3.0

• 支援單一通道 DDR記憶體介面

• 支援DDR400/333/266 DIMM 模組

• 支援高達2個非緩衝DIMM ，最多可安裝2 GB的記憶體

• 支援高達6個的PCI 主控擴充槽，完全相容於33MHz的 PCI 2.3 規

格

• 支援2 通道的Ultra ATA 100 匯流排主IDE 控制器

• SATA控制器最大可支援2個SATA裝置

• 相容於AC'97 v2.3，可支援6聲道之音訊輸出

• 8個 USB 埠，提供高達480 Mb/秒之串列傳輸速度。

記憶體

• 支援高達DDR400 /333/266 之DDR SDRAM記憶體模組

• 可安裝2個非緩衝式DIMM

• 每一DIMM支援1 GB，共可安裝2GB的記憶體

音頻

• 相容於AC’97 2.3 規格

• 支援為個人電腦多媒體系統設計的6聲道音訊CODEC功能

• 提供具有5位元音量控制功能的3種類比線級立體音效輸入：Lin-in、CD、及

AUX

• 符合Microsoft WHQL/WLP 2.0 音訊規格

繁體中文

Multi-Language Translation

機載LAN(選購)

本主機板搭載有如下其中一種LAN晶片組：

• 支援 10/100 Mb/秒N向自動辨識連線功能

• 支援半及全雙工

• 支援Wake-On-LAN (WOL)功能及遠端wake-up功能

• 整合有1000/100/10 收發器

• 支援PCI v2.3, 32位元, 33/66-MHz

• 完全支援IEEE 802.3、 IEEE802.3u 及IEEE802.3ab

擴充選項

主機板機載有下列擴充選項功能:

• 1個支援8X/4X 模式的AGP 3.0相容插槽(僅支援1.5伏特電壓規格介面)

• 5個32位元PCI插槽

• 2個40針IDE低通接頭(支援4個IDE通路)

• 1個軟體機介面

• 2個7針SATA插頭

本主機板支援傳輸率100/66 MB/秒下的Ultra DMA 匯流排主控功能。

繁體中文

整合的輸入出功能

本主機板完整地支援各種輸出入及連接器：

• 2個PS/2埠，分供滑鼠及鍵盤連接

• 1個串列埠

• 1個平行埠

• 4個USB埠

• 1個LAN埠(選購)

• 麥克風、線級輸入(line-in)及線級輸出(line-out)音效端子

BIOS韌體

本主機板使用了Award BIOS ，使用者可藉此對包括下列之系統功能進行設定

• 電源管理

• 喚醒警示

• CPU參數

• CPU及記憶體的定時

本BIOS也可用以設定各種有關處理器頻率的參數

有些硬體規格以及軟體物件將視狀況適當調整，不予另行通知。

Multi-Language Translation

功能

处理器

此主板使用 LGA775 型 Pentium 4/Celeron D/Pentium D CPU，具备以下特点：

• 支持 Intel Pentium 4/Celeron D/Pentium D 处理器

• 支持 800/533 MHz 系统总线 (FSB)

• 支持“多线程”技术 CPU

“多线程”技术可以让操作系统认为自己连接了两个处理器，允许两个线程并行运行，每个线程位于同一处理器中的单独“逻辑”处理器中。

芯片组

848P北桥 (NB) 和 ICH5 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构，能提供已经证明的可靠性和高性能。

848P (NB)

ICH5 (SB)

• 支持 266 MB/s 点对点连接到 ICH5 的 Hub 接口 (HI)

• 支持带 8X/4X AGP 数据传输和 8X/4X 快写功能的 AGP

3.0

• 支持单通道 DDR 存储接口

• 支持 DDR400/333/266 DIMM 内存模块

• 支持 2 个非缓冲 DIMM 内存条，最大内存可达 2 GB

• 支持 6 个 PCI 主控器，完全符合 PCI 2.3 规格（33

MHz）

• 支持 2 通道 Ultra ATA 100 总线主控 IDE 控制器

• SATA 控制器支持 2 个 SATA 设备

• 符合 AC’97 v2.3 规格，支持 6 声道音频输出

• 8 个用于串行传输的 USB 2.0 端口，最大传输速率可到

480Mb/Sec

内存

• 支持 DDR400/333/266 MHz DDR SDRAM 内存模块

• 支持 2 个非缓冲 DIMM

• 每个 DIMM 最大支持 1 GB，总共可支持 2 GB

音频

• 兼容 AC’97 v2.3 规格

• 支持为PC多媒体系统设计的 6 声道音频编解码器

• 提供 3 路带 5 位音量控制的模拟线路电平立体声输入：线入、CD 和

AUX

• 符合 Microsoft WHQL/WLP 2.0 音频要求

简体中文

Multi-Language Translation

简体中文

Onboard LAN (可选)

此主板支持以下任何一种 LAN 芯片组：

• 支持 10/100 Mb/s N 路自协商工作

• 支持半双工和全双工工作

• 支持 LAN 唤醒 (WOL) 功能和远程唤醒功能

• 集成 1000/100/10 收发器

• 支持 PCI v2.3，32-位，33/66-MHz

• 完全支持 IEEE 802.3，IEEE 802.3u和IEEE 802.3ab

扩展选项

此主板提供如下扩展选项：

• 1 个 8X/4X AGP 3.0 插槽(只支持 1.5V AGP 接口)

• 5 个 32 位 PCI v2.3 扩展槽

• 2 个 40-pin IDE 紧凑型接口，支持 4 个 IDE 通道

• 1 个软驱接口

• 2 个 7-pin SATA 接口

此主板支持 Ultra DMA 总线控制，传输速率可达 100/66 MB/sec。

集成 I/O

此主板具有完整的 I/O 端口和插孔：

• 2 个用于连接鼠标和键盘的 PS/2 端口

• 1 个串口

• 1 个并口

• 4 个 USB 端口

• 1 个 LAN 端口（可选）

• 麦克风、线入和线出声音插孔

BIOS

此主板使用 Award BIOS，可以让用户自己配置以下系统功能：

• 电源管理

• 唤醒报警

• CPU 参数

• CPU 和记忆的定时

还可用于设置不同处理器时钟速度的参数。

某些硬件规格和软件项目若有更改恕不另行通知。

Multi-Language Translation

Характеристики

Процессор

Плата построена на базе процессора следующими характеристиками:

• Обслуживает процессоры Intel Pentium 4/Celeron D/Pentium D

• Поддерживает системные шины (FSB) с частотой 800/533MHz

• Поддерживает технологию CPU “Hyper-Threading”

Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине имеется два процессора; это позволяет параллельно обслуживать два процесса, причем каждый из процессов обслуживается отдельным «логическим» процессором в пределах одного физического процессора.

Pentium 4/Celeron D/Pentium D LGA775 и обладает

Чипсет

Чипсеты 848P «Северный мост» (Northbridge, NB) и ICH5 «Южный мост» (Southbridge, SB) построены с использованием инновационной масштабируемой архитектуры, обеспечивающей высокую надежность и производительность.

848P (NB)

ICH5 (SB) • Поддерживает до щectь PCI Masters при полной

• Поддерживает интерфейс Hub Interface (HI) 1.5 с подсоединением 266 MБ/с point-to-point к ICH5

• Поддерживает AGP 3.0 со скоростью передачи данных 8X/4X AGP и скоростью записи 8X/ 4X

• Поддерживает одно- канальный интерфейс памяти DDR

• Поддерживает модели памяти DDR400/333/266 DIMM

• Поддерживает до два моделей небуферизуемой памяти DIMM (максимум 2 ГБ)

совместимости со спецификацией PCI 2.3, 33 MГц

• Поддерживает 2-канальный контроллер IDE Ultra ATA 100 bus master

• Контроллер SATA поддерживает два устройства SATA

• Соместима с AC’97 вер.2.3 и поддерживает 6канальный аудиовыход

• Поддерживает восемь портов USB 2.0 с максимальной скоростью передачи данных 480Mб/с

Русский

Память

• Поддерживает модули памяти DDR400/333/266 DDR SDRAM

• Обслуживает 2 модуля небуферизованной памяти DIMM

• Обслуживает до 1 ГБ на модуль DIMM (максимально до 2 ГБ памяти)

Аудио

• Совместимость со спецификацией AC’97 2.3

• Поддерживает 6-канальный аудио CODEC для мультимедиальных компьютерных систем

• Обеспечивает три аналоговых стереовхода с 5-битной регуляцией громкости: Line-in, CD, AUX

• Соответствие требованиям для аудио Microsoft WHQL/WLP 2.0

Multi-Language Translation

Русский

Встроенный сетевой адаптер LAN (опционально)

Встроенный сетевой адаптер LAN обладает следующими характеристиками:

• Поддерживает автоматическое определение скорости и режима соединения 10/100Mb/s

• Поддерживает режимы Half/Full duplex

• Поддерживает функции Wake-On-LAN(WOL) и remote wake-up

• Интегрированный трансивер 1000/100/10

• Поддеркжа PCI v2.3, 32-бит, 33/66-MГц

• Поддерживает технологии IEEE802.3, IEEE802.3u и IEEE802.3ab

Возможности расширения

Существуют следуюшие опции расширения данной материнской платы:

• Один слот, совместимый с AGP 3.0, обеспечивающий скорость 8X/4X (Поддерживает только интерфейс 1.5V AGP)

• Пять 32-битных слотов PCI v2.3

• Два 40-штырьковых низкопрофильных разъема IDE, обеспечивающих поддержку четырех устройств IDE

• Один разъем для накопителя на гибких дисках

• Два разъема 7-pin SATA

Плата поддерживает технологию захвата управления шиной скоростью передачи данных 100/66 МБ/сек.

UltraDMA bus mastering со

Интегрированный вход/выход

Плата снабжена полным набором портов входа/выхода и разъемов:

• Два порта PS/2 для подключения мыши и клавиатуры

• Один серийный порт

• Один параллельный порт

• Четыре порта USB

• Один порт LAN (опционально)

• Гнездо для подключения микрофона, гнезда аудио-входа и выхода

BIOS

Плата работает под Award BIOS, который позволяет пользователю конфигурировать различные характеристики системы:

• Управление питанием

• Сигналы пробуждения системы

• Параметры CPU

• Время доступа для CPU и памяти

BIOS допускает также установку параметров для различных частот процессора.

Некоторые параметры платы и характеристики ее программного обеспечения могут быть изменены без предварительного уведомления.

Multi-Language Translation

Cechy

Procesor

Ta płyta główna zaopatrzona jest w procesor Pentium 4/Celeron D/Pentium D typu LGA775 i charakteryzuje się następującymi cechami:

•

Przystosowana do obsługi procesorów Intel Pentium 4/Celeron D/Pentium D

• Obsługuje szynę systemowa (FSB) 800/533MHz

• Zabezpiecza technologię CPU “Hyper-Threading”

Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden z dwuch "logicznych" procesorów w ramach jednego ﬁzycznego procesora

Chipset

Mostek północny (NB) 848P i mostek południowy (SB) ICH5 chipsetu oparty jest na nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalności.

848P (NB)

• Obsługuje interfejs Hub Interface (HI) 1.5 z szybkością 266 MB/s połączeń point-to-point do ICH5.

• Obsługuje AGP 3.0 odpowiednio z szybkościami transferu 8X/4X AGP i zapisu 8X/ 4X.

• Obsługuje interfejs jednokanałowych pamięci DDR.

• Obsługuje moduły DDR400/333/266 DIMM.

• Obsługuje do dwa niebuforowanych DIMM o maksymalnej pojemności do 2 GB

ICH5 (SB)

• Obsługuje do sześć PCI Masters całkowicie zgodnych z PCI w wersji 2.3 o częstotliwości 33 MHz

• Obsługuje kontrolery 2 kanałów Ultra ATA 100 głównej szyny IDE

• Kontroler SATA obsługuje dwa urządzenia SATA

• Obsługuje 6 kanałowe wyjście audio zgodne z AC’97 w wersji 2.3

• Obsługuje osiem gniazd USB 2.0 o maksymalnej szybkości transferu danych 480Mb/s.

Pamięć

• Obsługuje pamięć DDR400/333/266 DDR SDRAM

• Zaopatrzony w dwa gniazda niebuforowanej pamięci typu DIMM

• Obsługuje pamięć DIMM do pojemności 1 GB każda; maksymalna możliwa pojemność pamięci do 2 GB

Audio

• Zgodne ze specyﬁkacją AC’97 w wersji 2.3

• Obsługuje 6 kanałów audio CODEC dla komputerowych systemów multimedialnych

• Zapewnia trzy wejściowe, analogowe linie stereo z 5 bitową regulacją głośności: Line-in, CD, AUX

• Spełnia wymagania stawiane audio przez ﬁrmę Microsoft w systemie WHQL/WLP 2.0

Multi-Language Translation

Polski

Zintegrowana obsługa sieci LAN (opcjonalnie)

Zintegrowana obsługa sieci LAN posiada następujące właściwości:

• Obsluguje N-drożne automatycznie ustalane operacje z szybkościami 10/100 Mb/s

• Zdolność Half/Full duplex

• Obsługuje funkcję Wake-On-LAN i zdalnie sterowane wake-up (uruchamianie komputera)

• Zintegrowany terminal nadawczo-odbiórczy 1000/100/10

• Obsluguje 32 bitowe PCI w wersji 2.3 o częstotliwościach 33/66-MHz

• Obsługuje wpełni IEEE802.3, IEEE802.3u oraz IEEE802.3ab

Możliwości rozbudowy

Płyta głwna wyposażona jest w następujące gniazda:

• Jedno gniazdo zgodne z AGP 3.0 o szybkości 8X/4X (obsluguje tylko karty AGP zasilane 1.5V).

• Pięć 32 bitowych gniazd PCI zgodnych z wersją 2.3.

• Dwa 40-nóżkowe, niskoproﬁlowe złącza zdolne obsłużyć cztery urządzenia IDE.

• Jedno złącze obsługujące stacje dyskietek

• Dwa 7-nóżkowe złącza SATA

Płyta główna obsługuje szynę UltraDMA z szybkością transferu 100/66 MB/s.

Zintegrowane We/Wy

Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:

• Dwa gniazda PS/2 dla myszy i klawiatury

• Jedno gniazdo szeregowe

• Jedno gniazdo równoległe

• Cztery gniazda USB

• Jedno gniazdo LAN (opcjonalnie)

• Gniazdo wejściowe mikrofonowe, gniazdo wejściowe i wyjściowe dzwięku (audio)

Firmowy BIOS

Płyta głwna wyposażona jest w BIOS ﬁrmy Award, który pozwala użytkownikowi konﬁgurować wiele cech systemu włączając w to następujące właściwości:

• Zarządzanie poborem mocy

• Alarmy typu Wake-up

• Parametry pracy procesora

• Ustalenia szybkoœci pracy procesora i pamiêci

BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara procesora.

Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie bez uprzedniego powiadomienia.

Multi-Language Translation

Vlastnosti

Procesor

Tato základní deska je určena pro procesory Pentium 4 /Celeron D/Pentium D LGA775 a může nabídnout následující vlastnosti:

• Použití pro procesory Intel Pentium 4/Celeron D/Pentium D

• Podporuje taktování systémové sběrnice (FSB) na frekvenci 800/533 MHz

• Podporuje technologii CPU „Hyper-Threading“

Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl připojen ke dvěma procesorům, protože je možné pracovat se dvěma toky programového kódu (vlákny) paralelně najednou, přičemž jsou k dispozici samostatné „logické“ procesory umístěné v rámci jednoho fyzického procesoru.

Čipová sada

Čipová sada 848P s northbridge (NB) a southbridge (SB) ICH5 je založena na inovativní a škálovatelné architektuře s ověřenou spolehlivostí a výkonem.

848P (NB)

• Podporuje rozhraní rozbočovače (HI) 1.5 s připojením mezi koncovými body s přenosovou rychlostí 266 MB/s ICH5

• Podporuje AGP 3.0 s přenosovými rychlostmi 8x/4x AGP a rychlostmi zápisu 8x/4x

• Podporuje jednokánálové rozhraní pamětí DDR

• Podporuje paměťové moduly DDR400/333/266 DIMM

• Podporuje až dvou moduly DIMM bez vyrovnávací paměti s maximální kapacitou 2 GB

ICH5 (SB) • Podporuje až pět PCI Master, plně dle standardu PCI 2.3

na frekvenci 33 MHz

• Podporuje 2 kanály sběrnice Ultra ATA 100 s řadičem IDE

• Řadič SATA podporuje 2 připojená zařízení SATA

• Splňuje požadavky standardu AC’97 v2.3, podporuje 6 výstupních audio kanálů

• Podporuje osm portů USB 2.0 pro sériový přenos dat maximální rychlostí 480 Mb/s

Paměť

• Podporuje paměťové moduly DDR SDRAM, DDR400/333/266

• Instalovat je možné až dvou DIMM moduly bez vyrovnávací paměti

• Až 1 GB paměti na jeden modul DIMM s maximální velikostí paměti do 2 GB

Zvuk

• Splňuje požadavky standardu AC’97 2.3

• Podpora 6kanálového zvukového kodeku určeného pro multimediální PC systémy

• Nabízí tří analogové linkové stereo vstupy s 5bitovým řízení hlasitosti:

LINE-IN, CD, AUX

• Splňuje požadavky pro audio zařízení Microsoft WHQL/WLP 2.0

Multi-Language Translation

Česky

Vestavění síťové rozhraní LAN (volitelně)

Vestavěné síťové rozhraní LAN nabízí následující možnosti:

• Podpora 10/100 Mb/s N–cestného automatického přepínání provozu

• Možnost polovičního a plného duplexu

• Podpora funkce Wake–On–LAN(WOL) a aktivace na dálku

• Integrovaný transceiver 1000/100/10

• Podpora rozhraní PCI v2.3, 32bitové, 33/66 MHz

• Podporuje plně IEEE802.3, IEEE802.3u a IEEE802.3ab

Možnosti rozšíření

Základní deska je dodávána s následujícími možnostmi rozšíření

• Jeden slot AGP 3.0 s přenosovými rychlostmi 8x/4x (podpora rozhraní – pouze 1,5 V AGP)

• Pět 32bitových patic PCI v2.3

• Dva nízkoproﬁlové 40kolíkové konektory IDE podporující připojení čtyř zařízení standardu IDE

• Jedno rozhraní pro disketovou mechaniku

• Dva 7kolíkové konektor SATA

Základní deska podporuje sběrnici Ultra DMA s přenosovými rychlostmi 100/66 MB/s.

Integrovaný vstup/výstup

Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:

• Dva porty PS/2 pro myš a klávesnici

• Jeden sériový port

• Jeden paralelní port

• Čtyři porty USB

• Jeden port LAN (volitelně)

• Zvukové konektory pro mikrofon, zvukový vstup a výstup

Česky

Firmware BIOS

Základní deska využívá BIOS formy Award, který uživateli umožňuje nakonﬁgurovat mnoho systémových parametrů, včetně následujících:

• Řízení spotřeby

• Alarmy při spouštění systému

• Parametry CPU

• Časování CPU a paměti

Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence procesoru.

Některé technické parametry hardware a software se mohou měnit bez předchozího upozornění.

Multi-Language Translation

Caracteristici

Procesorul

Această placă de bază utilizează Pentium 4/Celeron D/Pentium D de tipul LGA775, având următoarele caracteristici:

• Funcţionează cu procesoare Intel Pentium 4/Celeron D/Pentium D

• Funcţionează cu bus sistem (FSB) de 800/533 MHz

• Este compatibilă cu unităţi centrale dotate cu tehnologia „Hyper-

Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum ar exista două procesoare, putând ﬁ rulate în paralel două ﬁre, ﬁecare pe câte un procesor „logic” separat, aﬂate pe acelaşi procesor ﬁzic.

Threading”

Setul de chipuri

Seturile de chipuri 848P Northbridge (NB) şi ICH5 Southbridge (SB) se bazează pe o arhitectură inovatoare şi scalabilă, care s-a impus deja prin ﬁabilitate şi performanţă.

848P(NB)

• Suportă interfaţă Hub (HI) de 1,5 cu conexiune punct-lapunct de 266 MB/s la ICH5

• Suportă AGP 3.0 cu transfer de date AGP de 8X/4X şi scriere rapidă de 8X, respectiv 4X

• Suportă interfaţă de memorie DDR cu unh singur canal

• Suportă module DIMM DDR400/333/266

• Suportă până la două module DIMM fără zonă tampon, cu capacitate maximă de 2 GB

ICH5 (SB)

• Suportă până la şase masteri PCI compatibile complet cu

speciﬁcaţia PCI 2.3 la 33 MHz

• Suportă 2 canale de controleri IDE Ultra ATA 100 bus

master

• Controlerul SATA suportă două unităţi SATA

• Compatibil cu AC’97, versiunea 2.3, suportând 6 canale

de ieşire audio

• Suportă opt porturi USB 2.0 pentru trabsfer serial la viteza

maximă de 480 Mb/s

Memoria

• Suportă module de memorie DDR SDRAM DDR400/333/266

• Poate funcţiona cu două module DIMM fără zonă tampon

• Poate funcţiona cu module DIMM de cel mult 1 GB, iar cantitatea maximă de memorie este de 2 GB

Audio

• Compatibil cu speciﬁcaţia AC’97 2.3

• Suportă CODEC cu şase canale audio destinate sistemelor multimedia ale calculatoarelor

• Oferă trei intrări audio analoge stereo, cu un control al volumului sonor de 5 biţi: Intrare audio, CD, AUX

• Corespunde cerinţelor audio Microsoft WHQL/WLP 2.0

Multi-Language Translation

Română

Onboard LAN (opţional)

Onboard LAN are următoarele caracteristici:

• Suportă operaţii de autonegociere N-way de 10/100 Mb/s

• Posibilitate de semi-duplex sau duplex total

• Suportă funcţia Wake-On-LAN şi trezirea de la distanţă

• Unitate de emisie/recepţie 1000/100/10 integrat

• Suportă PCI, versiunea 2.3, de 32 biţi, la 33/66 MHz

• Pe deplin compatibil cu standardele IEEE802.3, IEEE802.3u şi IEEE802.3ab

Opţiuni de extindere

Placa de bază este dotată următoarele posibilităţi de extindere:

• Un slot compatibili cu AGP 3.0 cu viteze de 8X/4X (suportă doar interfaţă AGP de 1,5 V)

• Cinci sloturi PCI de 32 biţi compatibile cu versiunea 2.3

• Două conectoare IDE plate cu 40 de ace care suportă patru unităţi IDE

• O interfaţă pentru unitate ﬂoppy

• Două conectoare SATA 7

Placa de bază suportă bus mastering UltraDMA cu viteze de transfer de 100/66 MB/s

I/O integrată

Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:

• Două porturi PS/2, pentru mouse şi tastatură

• Un port serial

• Un port paralel

• Patru porturi USB

• Un port LAN (opţional)

• Mufe audio pentru microfon, intrare şi ieşire audio

Română

Firmware BIOS

Această placă de bază utilizează Award BIOS, care permite utilizatorului să conﬁgureze mai mulţi parametri ai sistemului, cum ar ﬁ:

• Gestionarea energiei

• Alarme de trezire

• Parametri CPU

• Temporizare CPU şi memorie

Acest ﬁrmware poate ﬁ utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale procesorului.

Anumite speciﬁcaţii hardware şi elemente de software pot ﬁ modiﬁcate fără înştiinţare prealabilă.

Multi-Language Translation

Спецификация

Процесор

Тази дънна платка използва Pentium 4/Celeron D/Pentium D тип LGA775 със следните спецификации:

• поддръжка на процесори Intel Pentium 4/Celeron D/Pentium D

• поддръжка на системна шина със скорост 800/533MHz

• поддръжка на процесори с технология “Hyper-Threading"

Технологията “ работи на два процесора, което дава възможност за паралелното изпълнение на две задачи на два отделни “логически” процесора в един и същ физически процесор.

Hyper-Threading" позволява да се “излъже” операционната система, че

Чипсет

Чŕпсетът със северен мост 848P и южен мост ICH5 е изграден на базата на оригинална архитектура с възможност за надстройка с доказана надеждност и производителност.

(NB) • Поддръжка хъб интерфейс (HI) 1.5 с 266 MB/s point-to-

848P

point връзка към моста ICH5

• Поддръжка на AGP 3.0 с трансфер на AGP данни 8X/4X и съответно 8X/ 4X fast writes

• Поддръжка на едноканален и двуканален интерфейс на паметта DDR

• Поддръжка на модули DDR400/333/266 DIMM

• Поддръжка на до четири небуферирани модула DIMM с общ максимален капацитет 2 GB

ICH5 (SB) • Поддръжка на до ШЕСТ PCI Master устройства, напълно

съвместимо със спецификацията PCI 2.3 при 33 MHz

• Поддръжка на двуканални Ultra ATA 100 bus master IDE контролери

• SATA контролер с поддръжка на две SATA устройства

• Съвместимост със спецификацията AC’97 v2.3 с поддръжка на 6-канално аудио

• Поддръжка на осем порта USB 2.0 за сериен трансфер на максимална скорост 480Mb/s

Памет

• Поддръжка на модули памет DDR400/333/266 MHz DDR SDRAM

• поддръжка на до два небуферирани DIMM слота

• до 1 GB памет на 1 DIMM канал с максимален капацитет 2 GB

Аудио

• Съвместимост със спецификацията AC’97 2.3

• Поддръжка на 6-канален аудио кодек за мултимедийни компютърни системи

• Три аналогови линейни стерео входа с 5-битов контрол на силата на звука: Line-in, CD, AUX

• Съответствие с изискванията на Microsoft WHQL/WLP 2.0

Multi-Language Translation

Български

Интегриран мрежов контролер (опция)

Спецификация на интегрирания мрежов контролер:

• Поддръжка на режими: 10/100 Mb/s с функция за определяне оптималната скорост на трансфер (N-Way Auto-negotiation).

• Half/Full duplex

• поддръжка на функция за “събуждане” Wake-On-LAN и дистанционен wake-up

• Интегриран 1000/100/10 контролер

• поддръжка на PCI v2.3, 32-bit, 33/66-MHz

• Пълна съвместимост с IEEE802.3, IEEE802.3u IEEE802.3ab

Възможности за разширяване

Дънната платка има следните разширителни възможности:

• Един слот AGP 3.0 8X/4X (поддържа само интерфейс 1.5V AGP)

• Пет слота 32-bit PCI v2.3

• Два нископрофилни 40-pin IDE колектора с поддръжка на четири IDE

устройства

• Един конектор за флопидисково устройство

• Два 7-щифтови SATA конектораs

Тази дънна платка поддържа UltraDMA директно управление на шината със скорости на трансфер 100/66 MB/s.

Интегриран Вход/Изход контролер

Дънната платка има пълен набор от I/O портове и конектори:

• Два PS/2 порта за мишка и клавиатура

• Един сериен порт

• Един паралелен порт

• Четири USB порта

• Един LAN порт (опция)

• Аудио жакове за микрофон, линеен вход и линеен изход

Български

BIOS Firmware

Дънната платка използва Award BIOS с възможност за различни системни настройки, включително

• управление на захранването

• Wake-up аларми

• параметри на процесора

• синхронизиране на процесора и паметта

настройка на скоростта на часовника на процесора

Хардуерните и софтуерни спецификации и параметри могат да бъдат изменени без предупреждение.

Multi-Language Translation

Jellemző

Processzor

Ez az alaplap LGA775 típusú Pentium 4/Celeron D/Pentium D számára készült, és a következő jellemzőkkel bír:

• Intel Pentium 4/Celeron D/Pentium D processzorokkal működik

• 800/533 MHz sebességű rendszerbuszt (FSB) támogat

• Támogatja a „Hyper-Threading” technológiát használó központi

A „Hyper-Threading” technológia által az operációs rendszer úgy működik, mintha két processzorral rendelkezne, ami két szál párhuzamos futását teszi lehetővé két független, ugyanazon ﬁzikai processzoron található „logikai” processzoron.

egységeket

Lapkakészlet

Az 848P Northbridge (NB) és ICH5 Southbridge (SB) lapkakészletek egy újító és méretezhető, nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.

848P (NB)

• Hub Interface (HI) 1,5 támogatása 266 MB/s ponttólpontig csatlakozást támogat az ICH5-tel

• AGP 3.0 támogatása 8-szoros/4-szeres AGP adatátvitellel, illetve 8-szoros/4-szeres gyors írás

• Egycsatornás DDR memória interfész támogatása

• DDR400/333/266 DIMM modulok támogatása

• Akár két puffer nélküli DIMM modult támogat, a maximális memória 2 GB

ICH5 (SB)

• Akár hat PCI mastert támogat, amely teljesen kompatibilis a PCI 2.3 speciﬁkációval 33 MHz-en

• Kétcsatornás Ultra ATA 100 bus master IDE vezérlők támogatása

• A SATA vezérlő két SATA egységet támogat

• Kompatibilis az AC’97 2.3-as verziójával, 6 csatornás audio kimenetet támogat

• Nyolc USB 2.0 port támogatása maximum 480 Mb/s soros átvitelre

Memória

• DDR400/333/266 DDR SDRAM memóriamodulokat támogat

• Két puffermentes DIMM egységgel működik

• Maximum 1 GB-os DIMM egységeket támogat, maximális memória 2 GB

Audio

• Megfelel az AC’97 2.3-as speciﬁkációnak

• A számítógép multimédiás rendszereinek szánt hat csatornás audio CODECet támogat

• Három analóg sztereo bemenetet biztosít 5 bites hangerő vezérléssel: bemenet, CD, AUX

• Megfelel a Microsoft WHQL/WLP 2.0 audio követelményeine

Multi-Language Translation

Magyar

Alaplapon levő LAN (választható)

Az alaplapon levő LAN jellemzői:

• 10/100 Mb/s N-Way automatikus beállítással

• Teljes/fél duplex lehetőség

• Támogatja a Wake-On-LAN (WOL) funkciót és a távoli ébresztést

• Integrált 1000/100/10 adó-vevő

• Támogatja a 32 bites, 33/66 MHz-es PCI 2.3-as változatát

• Teljesen kompatibilis az IEEE802.3, IEEE802.3u és IEEE802.3ab szbványoknak

Bővítési lehetőségek

Az alaplap a következő bővítési lehetőségekkel rendelkezik:

• Egy AGP 3.0 változattal kompatibilis 8-szoros/4-szeres sebességű foglalatot támogat (csak 1,5 V-os AGP interfészt támogat)

• Öt 32 bites, a PCI 2.3-as verziójával kompatibilis foglalattal rendelkezik

• Két 40 tűs lapos IDE csatlakozó, amelyek négy IDE eszközt képesek kiszolgálni

• Egy hajlékonylemez meghajtó interfész

• Két 7 tűs SATA csatlakozó

A alaplap támogatja az UltraDMA bus mastering megoldást, 100/66 MB/s sebességen

Beépített I/O

Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:

• Két PS/2 port az egér és a billentyűzet számára

• Egy soros port

• Egy párhuzamos port

• Négy USB port

• Egy LAN port (választható)

• Audio csatlakozók mikrofon, bemenet és kimenet számára

Magyar

BIOS Firmware

Az alaplapon levő Award BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja be, például:

• Energiagazdálkodás

• Ébresztési riasztások

• CPU paraméterek

• CPU és memória időzítés

A ﬁrmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.

Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül módosulhatnak.

Multi-Language Translation

ECS 848P-A7 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual