ECS 761GX-M754 V3.0 (Acer OEM) User Manual

iii

Preface

This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author.

Version 3.0

Disclaimer

The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.

Trademark Recognition

Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. AMD, Athlon, Sempron and Duron are registered trademarks of AMD Corporation. Other product names used in this manual are the properties of their respective owners and

are acknowledged.

Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment.

Preface

Declaration of Conformity

This device complies with part 15 of the FCC rules. Operation is subject to the following conditions:

• This device may not cause harmful interference, and

• This device must accept any interference received, including interference that may cause undesired operation.

Canadian Department of Communications

This class B digital apparatus meets all requirements of the Canadian Interference-causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada.

About the Manual

The manual consists of the following:

Chapter 1 Introducing the Motherboard

Describes features of the motherboard. Go to

page 1

Chapter 2 Installing the Motherboard

Chapter 3 Using BIOS

Chapter 4 Using the Motherboard Software

Chapter 5 SIS964 SAT A RAID Setup Guide

Describes installation of motherboard components.

Go to

Provides information on using the BIOS Setup Utility.

Go to

Describes the motherboard software Go to

Provides information about SATA RAID Setup

Go to

page 7

page 25

page 37

page 41

Preface

ABLE OF CONTENTSABLE OF CONTENTS

ABLE OF CONTENTS

ABLE OF CONTENTSABLE OF CONTENTS

Preface i

iii

Chapter 1

Introducing the Motherboard 1

Introduction................................................................................................1

Features.......................................................................................................2

Motherboard Components.......................................................................4

Chapter 2

Installing the Motherboard 7

Safety Precautions......................................................................................7

Choosing a Computer Case.......................................................................7

Installing the Motherboard in a Case......................................................7

Checking Jumper Settings.........................................................................8

Setting Jumpers..............................................................................8

Checking Jumper Settings..............................................................9

Jumper Settings..............................................................................9

Connecting Case Components...............................................................10

Front Panel Header.....................................................................12

Installing Hardware...................................................................................13

Installing the Processor...............................................................13

Installing Memory Modules.........................................................15

Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive........17

Installing a Floppy Diskette Drive...............................................19

Installing Add-on Cards..............................................................19

Connecting Optional Devices......................................................21

Connecting I/O Devices..........................................................................23

7 7

Chapter 3

Using BIOS 25

About the Setup Utility............................................................................25

The Standard Configuration........................................................25

Entering the Setup Utility..............................................................25

Updating the BIOS.......................................................................27

Using BIOS................................................................................................27

Standard CMOS Setup................................................................28

Advanced Setup Page..................................................................29

Features Setup Page....................................................................30

25 25

Power Management Setup Page..................................................31

PCI/Plug and Play Setup Page....................................................32

BIOS Security Features Setup Page.............................................33

CPU PnP Setup Page...................................................................33

Hardware Monitor Page..............................................................34

Load Optimal Defaults................................................................35

Save Changes and Exit................................................................35

Discard Changes and Exit.............................................................35

Chapter 4

37 37

Using the Motherboard Software 37

About the Software CD-ROM................................................................37

Auto-installing under Windows 98/ME/2000/XP................................37

Running Setup..............................................................................38

Manual Installation..................................................................................40

Utility Software Reference.......................................................................40

Chapter 5

41 41

SIS964 SATA RAID Setup Guide 41

Introduction for SiS964 SA T A RAID Function....................................41

Features......................................................................................................41

Support Operating Systems....................................................................41

What is RAID............................................................................................41

Installing Software Drivers......................................................................42

BIOS Utility Operation.............................................................................43

Multi-Language Translation

Chapter 1

Introducing the Motherboard

Introduction

Thank you for choosing this motherboard. This motherboard is a high performance, enhanced function motherboard that supports Socket 754 AMD Sempron/Athlon 64 processors for high-end business or personal desktop markets.

The motherboard incorporates the SiS761GX Northbridge (NB) and SiS964 Southbridge (SB) chipsets. The SiS761GX Northbridge on this motherboard features the HyperTranport complaint bus driver technology to support AMD Sempron/Athlon 64 processors up to 1600MT/s data rate. The Northbridge supports integrated Host-to-PCI Express Bridge, compliant with PCI Express spec.1.0a. Plus, SiS MuTIOL, a high bandwidth and mature technology, is incorporated to connect SiS761GX and SiS964 MuTIOL Media IO together.

The SiS964 Southbridge on this motherboard supports Hi-Precision Event Timer (HPET) for Microsoft Windows with multiple DMA bus architecture that supports isochronous request and continuous packet transmission. It implements an EHCI compliant interface that provides 480Mb/s bandwidth for eight USB 2.0 ports, integrates AC’97 v2.3 compliant audio controller that features a 6-channel audio speaker out and HSP v.90 modem support. The Southbridge integrates a Serial ATA host controller that is SATA v1.0 compliant, and supports 1.5Gb/s bandwidth for each serial port. It provides dual independent IDE channels and each of them support PIO mode 0,1,2,3,4 and multiword DMA mode 0,1,2 and UltraDMA 133/100/66.

There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and keyboard connectors, COM1, LPT, one VGA port and four USB ports, one optional LAN port, and audio jacks for microphone, line-in, and line-out. This motherboard is designed in a Micro ATX form factor using a four-layer printed circuit board and measures 244 mm x 204 mm.

Introducing the Motherboard

Feature

Processor

This motherboard uses a 754-pin socket that carries the following features:

• Accommodates AMD Sempron/Athlon 64 processors

• Supports up to 1600 MT/s HyperTransportTM (HT) interface speeds

HyperTransportTM Technology is a point-to-point link between two devices, it enables integrated circuits to exchange information at much higher speeds than currently available interconnect technologies.

Chipset

The SiS761GX Northbridge (NB) and SiS964 Southbridge (SB) chipset are based on an innovative and scalable architecture with proven reliability and performance.

SiS761GX(NB)

SiS964 (SB)

Memory

• Supports DDR400/333/266/200 DDR SDRAM DIMMs

• Accommodates two unbuffered DIMMs

• Up to 1GB per DIMM with maximum memory size up to 2 GB

• SiS MuTIOL is incorporated to connect SiS761GX and SiS964 MuTIOL Media IO

• Supports HyperTransport Technology up to 1600MT/s bandwidth

• Integrated Host-to-PCI Express Bridge, compliant with 16X/ PCI Express sepc. 1.0a

• Supports up to 128MB display memory with shared memory

• High Performance & High quality 3D Graphics Accelerator

• Concurrent servicing of all DMA Devices: Dual IDE Controllers, SATA controller, three USB 2.0/1.1 host controller, LAN MAC Controller and Audio/Modem DMA Controller

• Compliant with PCI 2.3 specificaiton supporting up to 6 PCI masters

• Compliant with Serial A TA 1.0 specification, supports power saving mode

• Compliant with AC’97 v2.3 supporting 6 Channels of audio outputs

• Integrated USB 2.0 Controller with three root hubs and eight function ports

T M

Graphics

• Built-in 32-bit floating point format VLIW triangle setup engine

• Built-in an 1T pipelined 128-bit BITBLT graphics engine

• Built-in Direct Draw & GDI+ Accelerator

• Supports up to 2048 x 2048 texture size

AC’97 Audio CODEC

• Compliant with AC’97 v2.3 specification

• 20-bit stereo full-duplex CODEC with independent and variable sampling rate

• Dual power support: Digital: 5V/3.3V Analog: 5V

Introducing the Motherboard

Expansion Options

The motherboard comes with the following expansion options:

• One PCI Express slot for Graphics interface

• Three 32-bit PCI slots

• Two IDE headers which support four IDE devices

• One floppy disk drive interface

• Two 7-pin SATA connectors

• One Communications Networking Riser (CNR1) slot

This motherboard supports Ultra DMA bus mastering with transfer rates of 133/100/66 MB/s.

Onboard LAN (optional)

The onboard LAN provides the following features:

• Supports 10/100 Mbps operation

• Supports half and full Duplex

• Supports IEEE 802.3u clause 28; 1.8V operation with 3.3V IO signal tolerance.

Integrated I/O

The motherboard has a full set of I/O ports and connectors:

• Two PS/2 ports for mouse and keyboard

• One serial port

• One parallel port

• One VGA port

• Four USB ports

• One LAN port (optional)

• Audio jacks for microphone, line-in and line-out

BIOS Firmware

The motherboard uses AMI BIOS that enables users to configure many system features including the following:

• Power management

• Wake-up alarms

• CPU parameters

• CPU and memory timing

The firmware can also be used to set parameters for different processor clock speeds.

Some hardware specifications and software items are subject to change without prior notice.

Introducing the Motherboard

Motherboard Components

Introducing the Motherboard

Table of Motherboard Components

LABEL COMPONENT

1 CPU Socket Socket 754 for AMD K8 processor 2 DIMM1~2 184-pin DDR SDRAM slots

3 FDD Floppy disk drive connector

4 ATX_POWER Standard 24-pin ATX power connector

5 IDE1 Primary IDE connector

6 IDE2 Secondary IDE connector 7 SYS_FAN System cooling fan connector

8 SATA1~SATA2 Serial ATA connectors

9 PANEL1 Front Panel switch/LED header

10 BIOS_WP BIOS flash protect jumper

11 USB3 ~ 4 Front Panel USB headers

12 CLR_CMOS Clear CMOS jumper

13 CNR1 Communications Networking Riser slot

14 SPDIFO1 SPDIF out header 15 CD_IN Analog Audio Input header

16 AUDIO2 Front panel audio header 17 PCI1~3 32-bit add-on card slots 18 PCIE1 PCI Express slot for graphics interface

19 CPU_FAN CPU cooling fan connector

20 ATX12V 4-pin +12V power connector

This concludes Chapter 1. The next chapter explains how to install the motherboard.

Introducing the Motherboard

Memo

Introducing the Motherboard

Chapter 2

Installing the Motherboard

Safety Precautions

• Follow these safety precautions when installing the motherboard

• Wear a grounding strap attached to a grounded device to avoid damage from

static electricity

• Discharge static electricity by touching the metal case of a safely grounded

object before working on the motherboard

• Leave components in the static-proof bags they came in

• Hold all circuit boards by the edges. Do not bend circuit boards

Choosing a Computer Case

There are many types of computer cases on the market. The motherboard complies with the specifications for the Micro ATX system case. First, some features on the motherboard are implemented by cabling connectors on the motherboard to indicators and switches on the system case. Make sure that your case supports all the features required. Secondly, this motherboard supports one or two floppy diskette drives and four enhanced IDE drives. Make sure that your case has sufficient power and space for all drives that you intend to install.

Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O template in the case matches the I/O ports installed on the rear edge of the motherboard.

This motherboard carries a Micro ATX form factor of 244 X 204 mm. Choose a case that accommodates this form factor.

Installing the Motherboard in a Case

Refer to the following illustration and instructions for installing the motherboard in a case. Most system cases have mounting brackets installed in the case, which correspond the holes

in the motherboard. Place the motherboard over the mounting brackets and secure the motherboard onto the mounting brackets with screws.

Ensure that your case has an I/O template that supports the I/O ports and expansion slots on your motherboard.

Installing the Motherboard

Do not over-tighten the screws as this can stress the motherboard.

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.

This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT

SHORT OPEN

Installing the Motherboard

Checking Jumper Settings

The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.

Jumper Settings

Jumper

CLR_CMOS 3-pin

BIOS_WP

Description

Type

CLEAR CMOS

3-pin BIOS PROTECT 1-2: DISABLE

Setting (default)

1-2: NORMAL 2-3: Clearing

Before clearing the CMOS, make sure to turn the system off.

2-3: ENABLE

Installing the Motherboard

CLR_CMOS

BIOS_WP

Connecting Case Components

After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:

1 Connect the CPU cooling fan cable to CPU_FAN. 2 Connect the system cooling fan connector to SYS_FAN 3 Connect the case switches and indicator LEDs to the PANEL1. . 4 Connect the standard power supply connector to ATX_POWER. 5 Connect the auxiliary case power supply connector to ATX12V.

Connecting 20/24-pin power cable

Users please note that the 20-pin and 24-pin power cables can both be connected to the ATX_POWER connector. With the 20-pin power cable, just align the 20pin power cable with the pin 1 of the ATX_POWER connector. However, using 20-pin power cable may cause the system to become unbootable or unstable because of insufficient electricity. A minimum power of 300W is recommended for a fully-configured system.

With ATX v1.x power supply, users please note that when installing 20-pin power cable, the latche of power cable falls on the left side of the ATX_POWER connector latch, just as the picture shows.

20-pin power cable

With ATX v2.x power supply , users please note that when installing 24-pin power cable, the latches of power cable and the ATX_POWER match perfectly.

24-pin power cable

Installing the Motherboard

CPU_FAN/SYS_F AN: FAN Power Connectors

Pin Signal Name Function

1 GND System Ground

2 +12V Power +12V

3 Sense Sensor

A TX_POWER: A TX 24-pin Power Connector

Pin Signal Name Pin Signal Name

1 +3.3V 13 +3.3V

2 +3.3V 14 -12V 3 Ground 15 Ground

4 +5V 16 PS_ON

5 Ground 17 Ground

6 +5V 18 Ground 7 Ground 19 Ground 8 PWRGD 20 -5V

9 +5VSB 21 +5V

10 +12V 22 +5V 11 +12V 23 +5V

12 +3.3V 24 Ground

A TX12V: A TX 12V Power Connector

Pin Signal Name

1 Ground

2 Ground 3 +12V

4 +12V

Installing the Motherboard

Front Panel Header

The front panel header (PANEL1) provides a standard set of switch and LED headers commonly found on ATX or micro-ATX cases. Refer to the table below for information:

Pin Signal Name Function

1 HDD+LED- Hard disk LED+ 2 SUS LED *MSG LED+

3 HDD+ LED- Hard disk LED-

5 RST SW Reset Switch

7 RST SW Reset Switch

9 NC Not connected

* MSG LED (dual color or single color)

Pin Signal Name Function

4 SUS LED *MSG LED-

6 PWR SW Power Switch

8 PWR SW Power Switch

10 Key No pin

Hard Drive Activity LED

Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data is being read from or written to the hard drive. For the LED to function properly, an IDE drive should be connected to the onboard IDE interface. The LED will also show activity for devices connected to the SCSI (hard drive activity LED) connector.

Power/Sleep/Message waiting LED

Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power on/off, sleep, and message waiting indication.

Reset Switch

Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact switch that is normally open. When the switch is closed, the board resets and runs POST.

Power Switch

Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal.

Installing the Motherboard

Installing Hardware

Installing the Processor

Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the motherboard, you may cause serious damage to the motherboard or its components.

On most motherboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed.

Avoid using cooling fans with sharp edges on the fan casing and the clips. Also, install the cooling fan in a well-lit work area so that you can clearly see the motherboard and processor socket.

Before installing the Processor

This motherboard automatically determines the CPU clock frequency and system bus frequency for the processor. You may be able to change these settings by making changes to jumpers on the motherboard, or changing the settings in the system Setup Utility. We strongly recommend that you do not over-clock processors or other components to run faster than their rated speed.

Warning: Over-clocking components can adversely affect the reliability of the system and introduce errors into your system. Over-clocking can permanently damage the motherboard by generating excess heat in components that are run beyond the rated limits.

This motherboard has a Socket 754 processor socket. When choosing a processor, consider the performance requirements of the system. Performance is based on the processor design, the clock speed and system bus frequency of the processor, and the quantity of internal cache memory and external cache memory.

Installing the Motherboard

CPU Installation Procedure

The following illustration shows CPU installation components.

1 Install your CPU. Pull up the lever away from the

socket and lift up to 90-degree angle.

2 Locate the CPU cut edge (the corner with the pin

hold noticeably missing). Align and insert the CPU correctly.

3 Press the lever down and apply thermal grease on

top of the CPU.

4 Put the CPU Fan down on the retention module and

snap the four retention legs of the cooling fan into place.

5 Flip the levers over to lock the heat sink in place and

connect the CPU cooling Fan power cable to the CPUFAN connector. This completes the installation.

To achieve better airflow rates and heat dissipation, we suggest that you use a high quality fan with 4800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The form and size of fan/heatsink may also vary.

Installing the Motherboard

Installing Memory Modules

This motherboard accommodates two 184-pin unbuffered Double Data Rate (DDR) SDRAM (Synchronous Dynamic Random Access Memory) memory modules, and can support DDR400/DDR333/DDR266/DDR200 memory types. Each module can be installed with 1GB of memory, and its total maximum memory size is 2 GB.

DDR SDRAM memory module table

Memory module Memory Bus

DDR200 100MHz DDR266 133MHz

DDR333 166MHz

DDR400 200MHz

Do not remove any memory module from its antistatic packaging until you are ready to install it on the motherboard. Handle the modules only by their edges. Do not touch the components or metal parts. Always wear a grounding strap when you handle the modules.

Installation Procedure

Refer to the following to install the memory modules.

1 This motherboard supports unbuffered DDR SDRAM only. 2 Push the latches on each side of the DIMM slot down. 3 Align the memory module with the slot. The DIMM slots are keyed with

notches and the DIMMs are keyed with cutouts so that they can only be installed correctly.

4 Check that the cutouts on the DIMM module edge connector match the notches

in the DIMM slot.

5 Install the DIMM module into the slot and press it firmly down until it seats

correctly. The slot latches are levered upwards and latch on to the edges of the DIMM.

6 Install any remaining DIMM modules.

Installing the Motherboard

T able A: Unbuffered DIMM Support for 754-pin

Numbers of

DIMMs

1 1

2 2 2

1 DIMM 1 connects to command/address pins MEMADDA [13:0], MEMBANKA [1:0], MEMRASA_L,

MEMCASA_L, MEMWEA_L, MEMCKEA.

2 DIMM 2 connects to command/address pins MEMADDB [13:0], MEMBANKB [1:0], MEMRASB_L,

MEMCASB_L, MEMWEB_L, MEMCKEB.

3 2T timing is supported in CG and later silicon revisions. Refer to the AMD Athlon™ 64 Processor

Power and Thermal Data Sheet, order #30430, for silicon revision determination.

4 The maximum allowable DRAM speed under these high load conditions may be reduced with certain

DIMMs due to signal integrity degradation.

4.1.5

DIMM 1

single rank

empty

double rank

empty

single rank

double rank

single rank

double rank

single ranksingle rank

double rank

single rank

double rank

DIMM 2

empty

Speed

1 T 2 T

DDR400

DDR333

DDR400

DDR333

Maximum DRAM

Table B: DDR (memory module) QVL (Qualified Vendor List)

The following DDR400 memory modules have been tested and qualified for use with this motherboard.

Size Vendor Model Name

SAMSUNG K4H560838D-TCC4

TwinMOS TMD7608F8E50D

256MB

KingMax KDL388P4EA-50A Winbond W942508BH-5

A-DATA ADD8608A8A-5B A-DATA ADD8608A8A-4.5B

Hynix HY5DU56822BT-D43

Infineon HYB25D256800BT-5 Kingston D3208DL1T-5 Kingston KHX3500AK2

PSC A2S56D30BTP

Hynix HY5DU56822DT-D5

Transcend V58C2256804SAT5B

ValueSelect VS32MB-5 2B0402

512 MB

CORSAIR CMX512-3200C2PT CORSAIR CMX512-3500C2PT CORSAIR CMX512-4400PT

Mushkin PC3500 level ONE

GEIL GE1GB3200BDC

G.SKILL F1-3200PHU2-1 GVZX

AENEON AED93T500 AENEON AED83T500

Team RD1024DB600EL

1GB CORSAIR CMX1024-3200PT

Installing the Motherboard

Installing a Hard Disk Drive/CD-ROM/SA T A Hard Drive

This section describes how to install IDE devices such as a hard disk drive and a CD-ROM drive.

About IDE Devices

Your motherboard has a primary and secondary IDE channel interface (IDE1 and IDE2). An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.

You must orient the cable connector so that the pin1 (color) edge of the cable correspoinds to the pin 1 of the I/O port connector.

IDE1: Primary IDE Connector

The first hard drive should always be connected to IDE1.

IDE2: Secondary IDE Connector

The second drive on this controller must be set to slave mode. The cinfiguration is the same as IDE1.

IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE. Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that one device is set to MASTER and the other device is set to SLAVE. The documentation of your IDE device explains how to do this.

About UltraDMA

This motherboard supports UltraDMA 133/100/66. UDMA is a technology that accelerates the performance of devices in the IDE channel. To maximize performance, install IDE devices that support UDMA and use 80-pin IDE cables that support UDMA 133/100/66.

Installing the Motherboard

About SAT A Connectors

Your motherboard features two SATA connectors supporting a total of two drives. SATA refers to Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard drives which are currently used in most PCs. These connectors are well designed and will only fit in one orientation. Locate the SATA connectors on the motherboard and follow the illustration below to install the SATA hard drives.

Installing Serial A T A Hard Drives

To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial ATA protocol. This SATA cable comes with an SATA power cable. You can connect either end of the SATA cable to the SATA hard drive or the connector on the motherboard.

SATA cable (optional)

Refer to the illustration below for proper installation:

1 Attach either cable end to the connector on the motherboard. 2 Attach the other cable end to the SATA hard drive. 3 Attach the SATA power cable to the SATA hard drive and connect the other

end to the power supply.

This motherboard does not support the “Hot-Plug” function.

SATA power cable (optional)

Installing the Motherboard

Installing a Floppy Diskette Drive

The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.

You must orient the cable connector so that the pin 1 (color) edge of the cable corresponds to the pin 1 of the I/O port connector.

FDD: Floppy Disk Connector

This connector supports the provided floppy drive ribbon cable. After connecting the single end to the onboard floppy connector, connect the remaining plugs on the other end to the floppy drives correspondingly.

Installing Add-on Cards

The slots on this motherboard are designed to hold expansion cards and connect them to the system bus. Expansion slots are a means of adding or enhancing the motherboard’s features and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.

Installing the Motherboard

PCIE1 slot The PCI Express x16 slot is fully compliant to the PCI Express Base

PCI Slots

CNR1 Slot

Follow these instructions to install an add-on card:

1 Remove a blanking plate from the system case corresponding to the slot you 2 Install the edge connector of the add-on card into the expansion slot. Ensure 3 Secure the metal bracket of the card to the system case with a screw.

Specification revision 1.0a as well

This motherboard is equipped with three standard PCI slots. PCI stands for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus standard. The PCI slots on this board are PCI v2.3 compliant.

This slot is used to insert CNR cards with Modem and Audio functionality.

Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation.

are going to use. that the edge connector is correctly seated in the slot.

For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-on card.

Installing the Motherboard

Connecting Optional Devices

Refer to the following for information on connecting the motherboard’s optional devices:

SPDIFO1: SPDIF out header

This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output to digital multimedia device through optical fiber or coaxial connector.

Pin Signal Name Function

1 SPDIF SPDIF digital output 2 +5VA 5V analog Power 3 Key No pin 4 GND Ground

AUDIO2: Front Panel Audio header

This header allows the user to install auxiliary front-oriented microphone and line-out ports for easier access.

Pin Signal Name Function

1 AUD_MIC Front Panel Microphone input signal 2 AUD_GND Ground used by Analog Audio Circuits 3 AUD_MIC_BIAS Microphone Power

4 AUD_VCC Filtered +5V used by Analog Audio Circuits 5 AUD_F_R Right Channel audio signal to Front Panel 6 AUD_RET_R Right Channel Audio signal to Return from Front Panel 7 REVD Reserved

8 Key No Pin 9 AUD_F_L Left Channel Audio signal to Front Panel 10 AUD_RET_L Left Channel Audio signal to Return from Front Panel

Pin Signal Name

Installing the Motherboard

SAT A1/SA T A2: Serial A T A connectors

These connectors are use to support the new Serial ATA devices for the highest date transfer rates (150 MB/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations of the current Parallel ATA interface. But maintains register compatibility and software compatibility with Parallel ATA.

Pin Signal Name

1 Ground 2 TX+

3 TX- 4 Ground 5 RX- 6 RX+

7 Ground - -

Pin Signal Name

USB3/USB4: Front Panel USB headers

The motherboard has four USB ports installed on the rear edge I/O port array. Additionally, some computer cases have USB ports at the front of the case. If you have this kind of case, use auxiliary USB connector to connect the front-mounted ports to the motherboard.

Pin Signal Name Function

1 USBPWR Front Panel USB Power 2 USBPWR Front Panel USB Power 3 USB_FP_P0- USB Port 0 Negative Signal

4 USB_FP_P1- USB Port 1 Negative Signal 5 USB_FP_P0+ USB Port 0 Positive Signal 6 USB_FP_P1+ USB Port 1 Positive Signal 7 GND Ground

8 GND Ground 9 Key No pin

10 NC Not connected

Please make sure that the USB cable has the same pin assignment as indicated above. A different pin assignment may cause damage or system hangup.

CD_IN: Analog Audio Input header

Pin Signal Name Function

1 CD in_L CD In left channel 2 GND Ground 3 GND Ground

4 CD in_R CD In right channel

Installing the Motherboard

Connecting I/O Devices

The backplane of the motherboard has the following I/O ports:

PS2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

PS2 Keyboard Use the lower PS/2 port to connect a PS/2 keyboard.

Parallel Port (LPT) Use LPT to connect printers or other parallel communications

devices.

Serial Port Use the COM port to connect serial devices such as mice or (COM1) fax/modems. COM1 is identified by the system as COM1/3.

VGA Port Connect your monitor to the VGA port.

LAN Port (optional) Connect an RJ-45 jack to the LAN port to connect your computer to the Network.

USB Ports Use the USB ports to connect USB devices.

Audio Ports Use the three audio ports to connect audio devices. The first jack

This concludes Chapter 2. The next chapter covers the BIOS.

is for stereo line-in signal. The second jack is for stereo line-out signal. The third jack is for microphone.

Installing the Motherboard

Memo

Installing the Motherboard

Chapter 3

Using BIOS

About the Setup Utility

The computer uses the latest American Megatrends BIOS with support for Windows Plug and Play. The CMOS chip on the motherboard contains the ROM setup instructions for configuring the motherboard BIOS.

The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are stored in battery-backed-up CMOS RAM that saves this information when the power is turned off. When the system is turned back on, the system is configured with the values you stored in CMOS.

The BIOS Setup Utility enables you to configure:

• Hard drives, diskette drives and peripherals

• Video display type and display options

• Password protection from unauthorized use

• Power Management features

The settings made in the Setup Utility affect how the computer performs. Before using the Setup Utility, ensure that you understand the Setup Utility options.

This chapter provides explanations for Setup Utility options.

The Standard Configuration

A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future.

This Setup Utility should be used:

• when changing the system configuration

• when a configuration error is detected and you are prompted to make changes to the Setup Utility

• when trying to resolve IRQ conflicts

• when making changes to the Power Management configuration

• when changing the password or making other changes to the Security Setup

Entering the Setup Utility

When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears:

Using BIOS

Press DEL to enter SETUP

Press the delete key to access the BIOS Setup Utility:

Standard CMOS Setup



Advanced Setup



Features Setup



Power Management Setup

  PCI/Plug and Play Setup

BIOS Security Features



: Move



F1: General Help

CPU PnP Setup



Hardware Monitor



Load Optimal Defaults

Save Changes and Exit

Discard Changes and Exit

+/-/: Value

F10: SaveEnter : Select

F9: Optimized Defaults

ESC: Exit

BIOS Navigation Keys

The BIOS navigation keys are listed below:

KEY FUNCTION

ESC Exits the current menu



 Scrolls through the items on a menu



+/- Modifies the selected field’s values

F1 Displays a screen that describes all key functions F9 Loads an optimized setting for better performance

F10 Saves the current configuration and exits setup

Using BIOS

Updating the BIOS

You can download and install updated BIOS for this motherboard from the manufacturer’s Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows:

1 If your motherboard has a BIOS protection jumper, change the setting to allow

BIOS flashing.

2 If your motherboard has an item called Firmware Write Protect in Advanced

BIOS features, disable it. (Firmware Write Protect prevents BIOS from being overwritten.

3 Create a bootable system disk. (Refer to Windows online help for information

on creating a bootable system disk.)

4 Download the Flash Utility and new BIOS file from the manufacturer’s Web

site. Copy these files to the system diskette you created in Step 3.

5 Turn off your computer and insert the system diskette in your computer’s

diskette drive. (You might need to run the Setup Utility and change the boot priority items on the Boot Configuration Features, to force your computer to boot from the floppy diskette drive first.)

6 At the A:\ prompt, type the Flash Utility program name and the file name of the

new BIOS, then press <Enter>

7 When the installation is complete, remove the floppy diskette from the diskette

drive and restart your computer. If your motherboard has a Flash BIOS jumper , reset the jumper to protect the newly installed BIOS from being overwritten.

Using BIOS

When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is currently selected. Use the cursor arrow keys to move the highlight to other options. When an option is highlighted, execute the option by pressing <Enter>.

Some options lead to pop-up dialog boxes that prompt you to verify that you wish to execute that option. Other options lead to dialog boxes that prompt you for information.

Some options (marked with a triangle values for the option. Use the cursor arrow keys to scroll through the items in the submenu.

In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a



triangle

 .



) lead to submenus that enable you to change the



Using BIOS

Standard CMOS Setup

This option displays basic information about your system.

System Time 00:01:25 System Date Fri 09/13/2005

Primary IDE Master Hard Disk Primary IDE Slave Not Detected Secondary IDE Master CD/DVD ROM Secondary IDE Slave Not Detected S-ATA 1 Not Detected

S-ATA 2 Not Detected

Floppy A 1.44 MB 3 1/2” Floppy B Disabled

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Standard CMOS Setup

Help Item

User [Enter], [TAB] or [SHIFT-TAB] to select a field. Use [+] or [-] to configure system time.

System Time & System Date

These items set up system date and time.

Primary/Secondary IDE Master/Slave

Your computer has two IDE channel and each channel can be installed with one or two devices (Master and Slave). In addition, this motherboard supports two SATA channels and each channel allows one SATA device to be installed. Use these items to configure each device on the IDE channel.

S-ATA1/S-ATA2 (Not Detected)

These items display the status of auto detection of S-ATA Devices when “Onboard SATAIDE” sets to” IDE”.

Floppy A/B (1.44MB 3 1/2”/Disabled)

These items set up size and capacity of the floppy diskette drive(s) installed in the system. Press <Esc> to return to the main menu page.

Using BIOS

Advanced Setup Page

This page sets up more advanced information about your system. Handle this page with caution. Any changes can affect the operation of your computer.

Share Memory Size Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Device Bootup Num-Lock Boot To OS/2 > 64 MB Auto Detect DIMM/PCI Clk Aperture Size Select Spread Spectrum Cool ‘N’ Quiet

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Advanced Setup

32MB Enabled WDC WD1200JB-00EV PIONEER DVD-ROM D 1st Floppy Drive Yes On No Enabled 64MB Disabled Enabled

Help Item

Options

32MB 64MB 128MB

Share Memory Size (32MB)

This item shows the VGA memory size borrowed from main memory capacity. In this case, 32MB is borrowed, which in the meanwhile the same the main memory loses.

Quick Boot (Enabled)

If you enable this item, the system starts up more quickly be elimination some of the power on test routines.

1st Boot Device/2nd Boot Device/3rd Boot Device(WDC WD1200JB-00EV/ PIONEER DVD-ROM D/1st Floppy Drive)

Use these items to determine the device order the computer uses to look for an operating system to load at start-up time.

Try Other Boot Device(Yes)

If you enable this item, the system will also search for other boot devices if it fails to find an operating system from the first two locations.

Bootup Num-Lock(On)

This item determines if the Num Lock key is active or inactive at system start-up time.

Boot To OS/2> 64MB (No)

Enable this item if you are booting the OS/2 operating system and you have more than 64MB of system memory installed.

Auto Detect DIMM/PCI Clk (Enabled)

When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI slots.

Aperture Size Select (64MB)

This item defines the size of aperture if you use a graphics adapter.

Spread Spectrum (Disabled)

If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic Interference) generated by the system.

Cool ‘N’ Quiet (Enabled)

This item helps the system lower the frequency when CPU idles. When the frequency decreases, the temperature will drop automatically as well.

Press <Esc> to return to the main menu setting page.

Using BIOS

Features Setup Page

This page sets up some parameters for peripheral devices connected to the system.

OnBoard Floppy Controller Serial Port1 Address Parallel Port Address Parallel Port Mode ECP Mode DMA Channel Parallel Port IRQ OnBoard PCI IDE Controller OnBoard SATA-IDE Audio Device Onboard LAN Device Onboard LAN Boot Rom OnBoard USB Function USB Function For DOS

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Features Setup

Enabled 3F8/IRQ4 378 ECP DMA3 IRQ7 Both IDE Enabled Enabled Disabled Enabled Disabled

Help Item

Allows BIOS to Enable or Disable Floppy Controller.

OnBoard Floppy Controller (Enabled)

Use this item to enable or disable the onboard floppy disk drive interface.

Serial Port1 Address (3F8/IRQ4)

Use this item to enable or disable the onboard COM1 serial port, and to assign a port address.

Parallel Port Address (378)

This item enables or disables the onboard LPT1 parallel port, and assigns a port address. The Auto setting will detect and available address.

Parallel Port Mode (ECP)

Use this item to set the parallel port mode. You can select Normal (Standard Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port), or EPP & ECP.

ECP Mode DMA Channel (DMA3)

When the onboard parallel port is set to ECP mode, the parallel port can use DMA 3 or DMA 1.

Parallel Port IRQ (IRQ7)

Use this item to assign IRQ to the parallel port.

OnBoard PCI IDE Controller (Both)

Use this item to enable or disable the onboard PCI IDE channel.

OnBoard SATA-IDE (IDE)

Use this item to choose IDE, RAID and Disabled to enable OnBoard SATA-IDE. The default setting is IDE.

Audio Device(Enabled)

This item enables or disables the onboard AC’97 audio chip.

OnBoard Lan Device (Enabled)

Enables and disables the onboard LAN device.

Using BIOS

Onboard LAN Boot ROM (Disabled)

Use this item to enable or disable the booting from the onboard LAN or a network add-in card with a remote boot ROM installed.

OnBoard USB Function (Enabled)

Enable this item if you plan to use the USB ports on this motherboard.

USB Function For DOS (Disabled)

Enable this item if you plan to use the USB ports on this motherboard in a DOS environment.

Press <Esc> to return to the main menu setting page.

Power Management Setup Page

This page sets up some parameters for system power management operation.

ACPI Aware O/S Power Management Suspend Time Out Resume on RTC Alarm LAN/Ring Power On Resume From USB Device ACPI Enhanced Efficiency

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Power Management Setup

Yes Enabled Disabled Disabled Disabled Disabled Disabled

Help Item

Enable/Disable ACPI support for Operating System

ENABLE: If OS supports ACPI

DISABLE: If OS does not support ACPI

ACPI Aware O/S (Yes)

This itme supports ACPI (Advanced Configuraion and Power Management Interface). Use this item to enable or disable the ACPI feature.

Power Management (Enabled)

Use this item to enable or disable a power management scheme. If you enable power management, you can use this item below to set the power management operation. Both APM and ACPI are supported.

Suspend Time Out (Disabled)

This item sets up the timeout for Suspend mode in minutes. If the time selected passes without any system activity, the computer will enter power-saving Suspend mode.

Resume on RTC Alarm (Disabled)

The system can be turned off with a software command. If you enable this item, the systemcan automatically resume at a fixed time based on the system’s RTC (realtime clock).Use the items below this one to set the date and time of the wake-up alarm. You must use an ATXpower supply in order to use this feature.

LAN/Ring Power On (Disabled)

The system can be turned off with a software command. If you enable this item, the system can automatically resume if there is an incoming call on the Modem/Ring, or traffic on the network adapter. You must use an ATX power supply in order to use this feature.

Using BIOS

Resume from USB Device (Disabled)

This option allows the activity of the USB devices to wake up the system from S3 sleep state.

ACPI Enhanced Efficiency (Disabled)

This item allows you to enable or disable ACPI Enhanced Efficiency function.

Press <Esc> to return to the main menu setting page.

PCI / Plug and Play Setup Page

This page sets up some parameters for devices installed on the PCI bus and those utilizing

. the system plug and play capability.

PCI / Plug and Play Setup

Primary Graphics Adapter PCI

Allocate IRQ to PCI VGA Yes

PCI IDE BusMaster Enabled

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Help Item

Options

PCI PCI Express Card

Primary Graphics Adapter (PCI)

This item helps you select which graphics controller to use as the primary boot device.

Allocate IRQ to PCI VGA (Yes)

If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system. You set this value to No to free up an IRQ.

PCI IDE BusMaster (Enabled)

This item enables or disables the DMA under DOS mode. We recommend you to leave this item at the default value.

Press <Esc> to return to the main menu setting page.

Using BIOS

BIOS Security Features Setup Page

This page helps you install or change a password.

Security Settings

Supervisor Password : Not Installed

Change Supervisor Password Press Enter

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

BIOS Security Features Setup

Help Item

Install or Change the password.

Supervisor Password

This item indicates whether a supervisor password has been set. If the password has been installed, Installed displays. If not, Not Installed displays.

Change Supervisor Password

You can select this option and press <Enter> to access the sub menu. You can use the sub menu to change the supervisor password. Press <Esc> to return to the main menu setting page.

CPU PnP Setup Page

This page helps you manually configure the mainboard for the CPU. The system will automatically detect the type of installed CPU and make the appropriate adjustments to the items on this page.

Processor

Type : AMD Athlon (tm) 64 Processor 3200+

CPU Clock 2 00 DRAM Frequency By SPD

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

CPU PnP Setup

Using BIOS

Help Item

CPU Freq Over Clock 100 to 250 Mhz

Manufacturer

These items show the brand of the CPU installed in your system.

CPU Clock (200 MHz)

This item allows you to adjust the CPU clock to 200MHz. You can key-in the numbers within the range to make a precise and ideal adjustment.

DRAM Frequency (By SPD)

This item shows the frequency of the DRAM in your system. Press <Esc> to return to the main menu setting page.

Hardware Monitor Page

This page sets up some parameters for the hardware monitoring function of this motherboard.

***System Hardware Monitor***

Vcore 1.488V Vdimm 2.528 V CPU FAN Speed 4560 RPM SYSTEM FAN Speed 0 RPM CPU Temperature 39oC/102oF SYSTEM Temperature 29oC/84oF

: Move Enter: Select +/-: Value F10: Save ESC: Exit







F1: General Help F9: Optimized Defaults

Hardware Monitor Setup

Help Item

System Component Characteristics

These items allow end users and technicians to monitor data provided by the BIOS on this motherboard. You cannot make changes to these fields.

• Vcore

• Vdimm

• CPU FAN /SYSTEM F AN Speed

• CPU/SYSTEM T emperature

Press <Esc> to return to the main menu setting page.

Using BIOS

Load Optimal Defaults

This option opens a dialog box that lets you install optimized defaults for all appropriate items in the Setup Utility. Press <OK> and then <Enter> to install the defaults. Press <Canel> and then <Enter> to not install the defaults. The optimized defaults place demands on the system that may be greater than the performance level of the components, such as the CPU and the memory. You can cause fatal errors or instability if you install the optimized defaults when your hardware does not support them. If you only want to install setup defaults for a specific option, select and display that option, and then press <F9>.

Save Changes and Exit

Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <OK> to save and exit, or press <Cancel> to return to the main menu:

Discard Changes and Exit

Highlight this item and press <Enter> to discard any changes that you have made in the Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears, press <OK> to discard changes and exit, or press <Cancel> to return to the main menu.

If you have made settings that you do not want to save, use the “Discard Changes and Exit” item and press <OK> to discard any changes you have made.

Using BIOS

Memo

Using BIOS

Chapter 4

Using the Motherboard Software

About the Software CD-ROM

The support software CD-ROM that is included in the motherboard package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the location for your motherboard version. More information on some programs is available in a README file, located in the same directory as the software.

Never try to install all software from folfer that is not specified for use with your motherboard.

Before installing any software, always inspect the folder for files named README.TXT, INSTALL.TXT, or something similar. These files may contain important information that is not included in this manual.

Auto-installing under Windows 98/ME/2000/XP

The Auto-install CD-ROM makes it easy for you to install the drivers and software for your motherboard.

If the Auto-install CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.

The support software CD-ROM disc loads automatically under Windows 98/ME/2000/XP. When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and Exit.

If the opening screen does not appear; double-click the file “setup.exe” in the root directory.

Using the Motherboard Software

Setup Tab

Setup

Browse CD

Exit The EXIT button closes the Auto Setup window.

Application Tab

Lists the software utilities that are available on the CD.

Read Me Tab

Displays the path for all software and drivers available on the CD.

Click the Setup button to run the software installation program. Select from the menu which software you want to install.

The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the contents of the support CD.

Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something similar. This file may contain important information to help you install the software correctly.

Some software is installed in separate folders for different operating systems, such as DOS, WIN NT, or WIN98/95. Always go to the correct folder for the kind of OS you are using.

In install the software, execute a file named SETUP.EXE or INSTALL.EXE by double-clicking the file and then following the instructions on the screen.

Running Setup

Follow these instructions to install device drivers and software for the motherboard:

1. Click Setup. The installation program begins:

The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing.

The motherboard identification is located in the upper left-hand corner.

Using the Motherboard Software

2. Click Next. The following screen appears:

3. Check the box next to the items you want to install. The default options are recommended.

4. Click Next run the Installation Wizard. An item installation screen appears:

5. Follow the instructions on the screen to install the items.

Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the installation.

Using the Motherboard Software

Manual Installation

Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your motherboard.

Look for the chipset and motherboard model; then browse to the directory and path to begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup program located in the operating system subfolder.

If the driver you want to install does not have a setup program, browse to the operating system subfolder and locate the readme text file (README.TXT or README.DOC) for information on installing the driver or software for your operating system.

Utility Software Reference

All the utility software available from this page is Windows compliant. They are provided only for the convenience of the customer. The following software is furnished under license and may only be used or copied in accordance with the terms of the license.

These software(s) are subject to change at anytime without prior notice. Please refer to the support CD for available software.

AMI/AWARD Flash Utility

This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard, and lets you copy an updated version of the BIOS to the chip. Proceed with caution when using this program. If you erase the current BIOS and fail to write a new BIOS, or write a new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for more information.

WinFlash Utility

The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility. The utility enables you to flash the system BIOS stored on a Flash Memory chip on the motherboard while in a Windows environment. This utility is currently available for WINXP\ME\2000\98SE. To install the WinFlash utility, run WINFLASH.EXE from the following directory: \UTILITY\WINFLASH 1.51

This concludes Chapter 4. Refer to the next chapter for information about SATA RAID Setup.

Using the Motherboard Software

Chapter 5

SiS 964 SA T A RAID Setup Guide

Introduction for SiS964 SA T A RAID Function

The 964 S-ATA controller only support two serial ATA on two independent ports. The Serial ATA RAID is designed to provide a cost-effective, high performance RAID solution that adds performance and/or reliability to PC desktops and/or servers using Serial ATA/150 hard disks.

Serial ATA RAID function supports striping (RAID 0), mirroring (RAID 1), and span (JBOD). Please note that the function supports hard disk drives only and the 964 S-ATA controller don’t support Striping + mirroring (Raid 0+1).

With striping, identical drives can read and write data in parallel to increase performance. Mirroring increases read performance through load balancing and elevator sorting while creating a complete backup of your files. Span would increase the logic hard disk space.

Serial ATA RAID striped arrays can double the sustained data transfer rate of Serial ATA/

150. Serial ATA RAID fully supports Serial ATA/150 specification of up to 150MB/sec per drive, depending on individual drive specifications.

Features

• The SiS 964 controller only support two Serial ATA (Serial ATA RAID) drivers.

• Support RAID function: RAID 0, RAID 1, JBOD.

• Support bootable disk.

• Windows-based RAID Utility software tool (only support Windows XP and

2000).

• BIOS Utility.

Support Operating Systems

Support Microsoft Windows 98/98SE/ME/2000 Professional and Server/XP.

What is RAID?

This section will give you an overview about the RAID system and introduce the basic background and glossary which you need to know before using “SiS RAID Controller Application”.

1 RAID: (Redundant Array of Independent Disk Drives) use jointly several hard

drives to increase data transfer rates and data security. It depends on the number of drives present and RAID function you select to fulfill the security or performance purposes or both.

2 RAID 0: Also known as “Stripping”. All of the data are distributed evenly to all

of the existing drives. You gain benefits on performance because the data transfer rate is multiplied by the number of drives. However, RAID 0 has high risks of data security. All of the stored data will be lost if even any one drive in the RAID set crashes.

3 RAID 1: Also known as “Mirroring”. Two hard drives are required. The goal of

RAID 0 is to ensure data security. Data is written to two or more drives synchronously. That is, 100% duplication of data from one drive to another.

SiS964 SAT A RAID Setup Guide

4 JBOD: (Just a Bunch of Drives). Also known as “Spanning”. Two or more hard

drives are required. Several hard disk types configured as a single hard disk. The hard drives are simply hooked up in series. This expands the capacity of your drive and results in a useable total capacity. However, JBOD will not increase any performance or data security.

Installing Software Drivers

SiS provides RAID driver for SiS 964 SATA with RAID function.

1 For RAID function, SiS 964 support RAID0, RAID1 and JBOD by software

RAID driver only.

2 Support the function of installing windows to RAID array.

New Windows 2000/XP Installation

1 Start the installation:

Boot from the CD-ROM. Press F6 when the message “Press F6 key if you

need to install third party SCSI or RAID driver” appears.

2 When the Windows 2000/XP Setup window is generated, press S key to

specify an Additional Device(s). 3 Insert the driver diskette into drive A: and press Enter. 4 Choose one of the following items:

“WinXP SiS Raid/IDE Controller”, “Win2000 SiS Raid/IDE Controller”,

that appears on screen, and then press the Enter key.

5 Press Enter to continue with installation or if you need to specify any addi-

tional devices to be installed, do so at this time. Once all devices are speci-

fied, Press Enter to continue with installation. 6 From the Windows 2000/XP Setup screen, press the Enter key. Setup will

now load all device files and then continue the Windows 2000/XP instal-

lation. 7 Please install the driver package again (ex. SiS RAID driver v1.00) while the

operation system has been setup.

If you would like to install windows to any RAID set, you should create RAID from BIOS utility or SiS 964 RAID Utility first and then follow the steps above.

Existing Windows 2000/XP/98/Me Installation

1 Install the driver by executing SiS driver setup utility. 2 The drivers will be automatically installed.

Confirming Windows 2000/XP Driver Installation

1 From Windows 2000/XP , open the Control Panel from “My Computer” followed

by the System icon. 2 Choose the “Hardware” tab, then click the “Device Manager” tab. 3 Click the “+” in front of “SCSI and RAID Controllers” hardware type. The driver

“SiS 180 Raid Controller” should appear.

SiS964 SAT A RAID Setup Guide

Confirming Windows 98/Me Driver Installation

1 From Windows 98/Me, open the Control Panel from “My Computer” followed

by the System icon. 2 Choose the “Device Manager” tab. 3 Click the “+” in front of “IDE ATA/AT API Controllers” hardware type. The driver

“SiS 180 IDE Dual Channel” and “SiS 180 IDE/RAID Controller” should

appear.

BIOS Utility Operation

BIOS Utility supports windows 2000/XP/98/Me.

St arting BIOS Utility

1 Boot your system. If this is the first time you have booted with the SiS 964 and

the drives installed, the BIOS will display the following:

Press <Ctrl.<S> to run BIOS Setting Utility

2 Press <Ctrl-S> keys to display the SiS 964 Utility Main Menu.

3 You can press <B> key to select the boot disk on the 964 controller. The

yellow highlight will show on the disk and you can switch it to select the disk

you wanted. Press “Enter” key to select it and the selected boot device will be

marked by “*”. The default boot device will be set as Disk 1. 4 Press <R> to display the RAID setup menu below. This is the fastest and

easiest method to creating your first array.

SiS964 SAT A RAID Setup Guide

Create RAID

• SIS 964 controller support RAID 0, RAID 1 and JBOD.

Creating a RAID 0 (Stripe) Array for Performance

• SIS 180 enables users to create striped arrays with 2, 3, or 4 drives.

• SIS 964 only supports 2 SATA drivers to create a stripe array.

To create an array for best performance, follow these steps:

1 Press <A> to start creating a RAID array. 2 Press <2> and <Enter> to select RAID 0.

3 You will have two selections to create a RAID 0 array. The default value is

<1>. If you select <1>Auto Create, you can create a RAID 0 array faster and easier. The Blocksize will be selected by its default value “64K”. The result after creating will be show on step 8. Besides, you also can select <2>Manual Create, see following steps.

4 Press <1>-<5> keys and <Enter> to select Block Size. (Default:64K)

SiS964 SAT A RAID Setup Guide

5 Use <↑ > < ↓ > to select disk, and press <Enter> to select disk, <Q> to exit.

When you press <Enter> on the disk you wanted, the RAID Type will be

changed from Single to RAID 0. An the disk you select first will be the SOURCE

disk.

6 Next, you will see a message “Split the SOURCE(DISK x) data to RAID disks?”.

Press <N> and <Enter> to create RAID 0 array only or press <Y> and <Enter>

to split the data from source disk to other disks.

7 Starting splitting action, the following frame will be shown.

8 After all steps finished, press ,<Q> until escape the setup menu and RAID 0

array will be show on the top of the main frame.

SiS964 SAT A RAID Setup Guide

9 Press <Q> again to exit this BIOS utility and the red message frame will show.

Press <Y> and <Enter> to save changes.

10 Once the array has been created, you will need to FDISK and format the array

as if it were a new single hard drive.

Creating a RAID 1 (Mirror) Array

SIS 964/180 enables users to create Mirror arrays with 2 drives only.

To create a Mirror array, follow these steps:

1 Press <A> to start creating a RAID array. 2 Press <3> and <Enter> to select Mirror.

3 You will have two selections to create a RAID 1 array. The default value is

<1>. If you select <1>Auto Create, you can create a RAID 1 array faster and easier. The result after creating will be show on step 7. Besides, you also can select <2>Manual Create, see following steps.

SiS964 SAT A RAID Setup Guide

4 Use <↑ > < ↓ > to select disk, and press <Enter> to select disk, <Q> to exit.

When you press <Enter> on the disk you wanted, the RAID Type will be

changed from Single to RAID 1. The same as RAID 0, the disk you select first

will be the SOURCE disk.

5 Next, you will see a message “Duplicate the SOURCE (DISK x) data to RAID

disks?”. Press <N> and <Enter> to create RAID 1 array only or press <Y> and

<Enter> to duplicate the data from source disk to mirror disk.

6 Starting duplicating action, the following frame will be showing.

7 After all steps finished, press <Q> until escape the setup menu and RAID 1

array will be show on the top of the main frame.

SiS964 SAT A RAID Setup Guide

8 Press <Q> again to exit this BIOS utility and the red message frame will show

as the same as the creation of the RAID 0 array. Press <Y> and <Enter> to save changes.

9 Once the array has been created, you will need to FDISK and format the array

as if it were a new single hard drive.

Creating a JBOD Array

1 SIS 180 enables users to create JBOD arrays with 2,3, or 4 drives. 2 SIS 964 only supports 2 SATA drivers to create a JBOD arrays.

To create an JBOD array, follow these steps:

1 Press <A> to start creating a RAID array. 2 Press <1> and <Enter> to select JBOD. 3 You will have two selections to create a JBOD array. The default value is

<1>. If you select <1>Auto Create, you can create a JBOD array faster and easier. The result after creating will be show on step 5. Besides, you also can select <2>Manual Create, see following steps.

4 Use <↑> < ↓ > to select disk, and press <Enter> to select disk, <Q> to exit.

When you press <Enter> on the disk you wanted, the RAID Type will be changed from Single to JBOD.

5 After all steps finished, press <Q> until escape the setup menu and JBOD

array will be show on the top of the main frame.

SiS964 SAT A RAID Setup Guide

6 Press <Q> again to exit this BIOS utility and the red message frame will show

as the same age as the creation of the RAID 0 array. Press <Y> and <Enter>

to save changes. 7 Once the array has been created, you will need to FDISK and format the array

as if it were a new single hard drive.

This concludes Chapter 5.

SiS964 SAT A RAID Setup Guide

Multi-Language Translation

Français

Les chipsets SiS761GX Northbridge (NB) et SiS964 Southbridge (SB) sont basés sur une architecture novatrice et dimensionnable avec une ﬁabilité et des performances prouvées.

SiS761GX(NB)

• SiS MuTIOL est incorporé pour connecter les ES Médias MuTIOL SiS761GX et SiS964

• Prend en charge la Technologie HyperTransport

T M

jusqu’à

une bande passante de 1600MT/s

• Pont Hôte vers PCI Express intégré, conforme à PCI Express sepc. 16X 1.0a

• Prend une mémoire d’afﬁchage allant jusqu’à 128Mo avec mémoire partagée

• Accélérateur Graphique 3D de Haute Performance & Haute Qualité

Mémoire

• Prend en charge les types de mémoire DDR400/333/266/200DDR SDRAM DIMMs

• Reçoit quatre DIMM sans tampon

• Jusqu’à 1 Go par DIMM avec une taille de mémoire maximum de 2 Go

Chipset

SiS964 (SB)

• Entretien simultané pour tous les Périphériques DMA: Contrôleurs IDE Doubles, contrôleur SATA, trois contrôleurs d’hôte USB 2.0/1.1, Contrôleur MAC LAN et Contrôleur DMA Audio/Modem

• Conforme aux spéciﬁcations PCI 2.3 prenant en charge jusqu’à 6 maîtres PCI

• Conforme aux spéciﬁcations ATA 1.0 Série, supporte le mode d’économie d’énergie

• Conforme à AC’97 v2.3 prenant en charge 6 Canaux de sorties audio

• Contrôleur USB 2.0 intégré avec trois hubs racine et huit ports de fonction.

Graphique

• Moteur d’installation en triangle VLIW au format de virgule ﬂottante en 32 bits intégré

• Moteur graphique BITBLT 128 bits en pipeline en 1T intégré

• Accélérateur Direct Draw & GDI+ Intégré

• Supporte jusqu’à la taille de texture de 2048 x 2048

Caractéristiques

Processeur

Cette carte mère utilise un socket de 754 broches ayant les caractéristiques suivantes :

• Reçoit les CPU AMD Sempron/Athlon 64

• Prend en charge des vitesses d’interface HyperTransportTM (HT) allant jusqu’à 1600MT/s

La Technologie HyperTransport

est une liaison point à point entre deux matériels, elle permet à des circuits intégrés d’échanger des informations à des vitesses bien plus élevées que ne le permettent les technologies à interconnexions actuellement disponibles.

CODEC Audio AC’97

• Conforme aux spéciﬁcations AC’97 v2.3

• CODEC full-duplex -20 bits avec vitesse d’échantillonnage indépendante et variable

• Support d’alimentation double : Numérique : Analogique 5V/3,3V: 5V

Multi-Language Translation

Français

Cette carte mère prend en charge la maîtrise de bus Ultra DMA avec des vitesses de transfert de 133/100/66 Mo/s.

La carte mère est livrée avec les options d’extensions suivantes:

• Un logement PCI Express pour interface Graphique

• Trois logements PCI 32 bits

• Deux connecteurs IDE prenant en charge jusqu’à quatre périphériques IDE

• Une interface de lecteur de disquette

• Deux connecteurs SATA à 7 broches

• Un logement Communications Network Riser (CNR1)

Options d’extension

LAN interne (optionnel)

• Supporte le fonctionnement en 10/100 Mbps

• Supporte half et full Duplex

• Supporte IEEE 802.3u clause 28; fonctionnement en 1,8V avec une tolérance de signal d’ES de 3,3V.

Le LAN interne offre les caractéristiques suivantes:

E/S intégrées

La carte mère possède un jeu complet de ports d’E/S et de connecteurs:

• Deux ports PS/2 pour souris et clavier

• Un port série

• Un port parallèle

• Un port VGA

• Quatre ports USB

• Un port LAN (optionnel)

• Prises audio pour microphone, ligne d’entrée et ligne de sortie

Microprogramme BIOS

La carte mère utilise AMI BIOS qui permet aux utilisateurs de conﬁgurer de nombreuses caractéristiques du système comprenant les suivantes:

• Gestion de l’alimentation

• Alarmes de réveil

• Paramètres de CPU

• Synchronisation du CPU et de la mémoire

Le microprogramme peut aussi être utilisé pour déﬁnir les paramètres pour les vitesses d’horloges de différents processeurs.

Certaines spéciﬁcations matérielles et éléments de logiciels peuvent être modiﬁés sans avertissement.

Multi-Language Translation

Deutsche

Die SiS761GX Northbridge (NB) und SiS964 Southbridge (SB) Chipsätze basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit und Leistung

SiS761GX(NB)

• SiS MuTIOL verbindet SiS761GX und SiS964 MuTIOL Media IO

• Unterstützt HyperTransport TMTechnologie mit einer Bandbreite von bis zu 1600MT/s

• Integrierte Host-zu-PCI Express Brücke, entspricht 16X PCI Express Speziﬁkation 1.0a

• Unterstützt bis zu 128MB Anzeigenspeicher mit Shared Memory

• Hochleistungsfähiger Qualitäts-3D-Graﬁkbeschleuniger

Speicher

• Unterstützt DDR400/333/266/200 DDR SDRAM DIMMs

• Es können zwei ungepufferte DIMMs aufgenommen werden.

• Bis zu 1 GB pro DIMM mit maximaler Speicherkapazität von bis zu 2 GB.

AC’97 Audio CODEC

Chipsatz

SiS964 (SB)

• Gleichzeitige Bearbeitung aller DMA-Geräte: Duale IDE-Con-

troller, SATA-Controller, drei USB 2.0/1.1 Host-Controller, LAN MAC-Controller und Audio/Modem DMA-Controller

• Entspricht PCI 2.3 Speziﬁkation und unterstützt bis zu 6 PCI-

Masters

• Entspricht Serial ATA 1.0 Speziﬁkation und unterstützt

Energiesparmodus

• Entspricht AC’97 v2.3 und unterstützt 6-Kanal-Audioausgaben

• Integrierte-USB 2.0-Controller mit drei Root Hub und acht

Port.

Graﬁk

• Integrierter 32-Bit Fließkomma VLIW-Triangle Setup Engine

• Integrierter 1T pipelined 128-Bit BITBLT-Graﬁk-Engine

• Eingebauter Direct Draw & GDI+ Beschleuniger

• Unterstützt bis zu 2048 x 2048 Strukturengröße

• Entspricht AC’97 v2.3 Speziﬁkation

• 20-Bit Stereo Vollduplex CODEC mit unabhängiger und variabler Samplingrate

• Dual Netzteilunterstützung: Digital: 5V/3.3V Analog: 5V

Feature

Prozessor

Dieses Motherboard verwendet einen 754-Pin Socket mit den folgenden Eigenschaften:

• Nimmt AMD Sempron/Athlon 64 auf

• Unterstützt bis zu 1600MT/s HyperTransportTM(HT) InterfaceGeschwindigkeiten

HyperTransport

Technologie ist ein Punkt-zu-Punkt Link zwischen zwei Geräten. Es ermöglicht integrierten Schaltkreisen einen Informationsaustausch mit wesentlich höherer Geschwindigkeit als bei gängigen Interconnect-Technologien.

Multi-Language Translation

Deutsche

Dieses Motherboard unterstützt Ultra DMA Bus-Mastering mit Transferraten von 133/100/ 66MB/s.

Das Motherboard bietet die folgenden Erweiterungsoptionen:

• Ein PCI Express Steckplatz für Graﬁkschnittstelle

• Drei 32-Bit PCI-Steckplätze

• Zwei IDE-Stecker, die bis zu vier IDE-Geräte unterstützen

• Ein Steckplatz für ein Diskettenlaufwerk

• Zwei 7-Pin SATA-Stecker

• Einen Steckplatz für Communications Network Riser (CNR1)

Erweiterungsoptionen

Integriertes

LAN (optional)

• Unterstützt 10/100 Mbps Betrieb

• Unterstützt Halb-/Vollduplex

• Unterstützt IEEE 802.3u Abschnitt 28; 1.8V Betrieb mit 3,3V IO Signaltoleranz.

Das integrierte LAN bietet folgende Features:

Integrierte I/O-Schnittstellen

Das Motherboard verfügt über einen kompletten Satz von I/O-Schnittstellen und Anschlüssen:

• Zwei PS/2-Schnittstellen für Tastatur und Maus

• Eine serielle Schnittstelle

• Eine parallele Schnittstelle

• Eine VGA- Schnittstelle

• Vier USB- Schnittstellen

• Eine LAN-Schnittstelle (optional)

• Audiobuchsen für Mikrofon, Line-In und Line-Out

BIOS Firmware

Dieses Motherboard setzt das AMI BIOS ein, mit dem der Anwender viele Systemeigenschaften selbst konﬁgurieren kann, einschließlich der folgenden:

• Energieverwaltung

• Wake-up Alarm

• CPU-Parameter

• CPU- und Speichertiming

Mit der Firmware können auch Parameter für verschiedene Prozessortaktgeschwindigkeiten eingestellt werden.

Einige Hardware- und Software-Speziﬁkationen können jederzeit und ohne vorherige Ankündigung geändert werden.

Multi-Language Translation

Italiano

I chipset SiS761GX Northbridge (NB) e SiS964 Southbridge (SB) sono basati su un’innovativa architettura scalabile e offrono collaudata afﬁdabilità e prestazioni comprovate.

SiS761GX(NB) • La tecnologia SiS MuTIOL incorporata consente di collegare

insieme MuTIOL Media I/O SiS 761GX e SiS 964

• Supporto di tecnologia HyperTransportTM con larghezza di banda ﬁno a 1600 MT/s

• Bridge Host-to-PCI Express integrato conforme alla speciﬁca 16X PCI Express 1.0a

• Supporto di memoria video ﬁno a 128MB con memoria condivisa

• Acceleratore graﬁco 3D a elevate prestazioni e qualità

Memoria

• Supporta DDR 400/333/266/200 DDR SDRAM DIMM

• Alloggia 2 DIMM unbuffered

• Dimensione massima della DIMM pari ad 1 GB per un ammontare massimo di 2 GB di memoria

CODEC Audio AC’97

Chipset

SiS964 (SB)

• Supporto simultaneo di tutti i componenti DMA: doppio controller IDE, controller SATA, tre host controller USB 2.0/

1.1, controller LAN MAC e controller DMA Audio/Modem

• Conforme alle speciﬁche PCI 2.3, in grado di supportare ﬁno a 6 master PCI.

• Conforme alla speciﬁca ATA Seriale 1.0 con supporto di modalità di risparmio energia

• Conforme alla speciﬁca AC’97 v2.3 con supporto di 6 canali audio in uscita

• Controller USB 2.0 integrato con tre hub e otto porte funzione

Graﬁca

• Motore triangle setup con architettura VLIW a virgola mobile a 32 bit integrato

• Motore graﬁco BITBLT a 128 bit con pipeline 1T integrato

• Acceleratore GDI+ e Direct Draw integrati

• Supporto di dimensioni di trama ﬁno a 2048 x 2048

• Conforme alla speciﬁca AC’97 v2.3

• CODEC full-duplex stereo a 20 bit con velocità di campionamento indipendente e variabile

• Duplice supporto di alimentazione: Digitale: 5 V/3,3 V Analogico: 5 V

Caratteristiche

Processore

La scheda madre utilizza una presa a 754 pin che offre le seguenti caratteristiche:

• Compatibilità con CPU AMD Sempron/Athlon 64

• Supporto di velocità di interfaccia HyperTransportTM (HT) ﬁno a 1600 MT/s

La tecnologia HyperTransport

consente il collegamento point-to-point fra due dispositivi e quindi un trasferimento di informazioni tra circuiti integrati molto più veloce di quanto sia possibile con le attuali tecnologie di interconnessione.

Multi-Language Translation

Italiano

La scheda madre supporta la funzionalità di bus mastering Ultra DMA con velocità di trasferimento di 133/100/66 MB/s.

La scheda madre è dotata delle seguenti opzioni di espansione:

• Uno slot PCI Express per interfaccia graﬁca

• Tre slot PCI a 32 bit

• Due connettori IDE per il supporto di ﬁno a quattro dispositivi IDE

• Un’interfaccia per unità disco ﬂoppy

• Due connettori SATA a 7 pin

• Una slot Communications e Network Riser (CNR1)

Opzioni di espansione

LAN integrata (opzionale)

• Supporto di operazioni a 10/100 Mbps

• Supporto di Half/Full Duplex

• Supporto di IEEE 802.3u clause 28; funzionamento a 1,8 V con tolleranza di segnale I/O 3,3 V

La funzionalità LAN integrata sulla scheda offre le seguenti caratteristiche:

I/O integrati

La scheda madre offre una serie completa di porte e connettori I/O:

• Due porte PS/2 per mouse e tastiera

• Una porta seriale

• Una porta parallela

• Una porta VGA

• Quattro porte USB

• Una porta LAN (opzionale)

• Prese jack audio per microfono, line-in e line-out

Firmware BIOS

La scheda madre si avvale del BIOS AMI che consente la conﬁgurazione personalizzata di molte funzionalità del sistema, tra cui:

• Gestione dell’alimentazione

• Allarmi di attivazione

• Parametri CPU

• Sincronizzazione di CPU e memoria

Il ﬁrmware consente inoltre di impostare i parametri per diverse velocità di clock del processore.

Alcune speciﬁche hardware e voci di software possono essere modiﬁcate senza preavviso.

Multi-Language Translation

Español

El chipset SiS761GX Northbridge (NB) y SiS964 Southbridge (SB) se basan de una arquitectura innovadora y escalable con ﬁabilidad y rendimiento comprobados.

SiS761GX(NB) • SiS MuTIOL está incorporado para conectar SiS761GX y

SiS964 MuTIOL Media IO

• Soporta la HyperTransport TMTechnology hasta una ancha de banda de 1600MT/s

• Puente Anﬁtrión-a-PCI Express Integrado, conforme con 16X PCI Express espc. 1.0a

• Soporta hasta la memoria de muestra de 128MB con memoria compartida

• Acelerador de Gráﬁcas 3D de Alto Rendimiento & Alta Calidad

Memoria

• Soporta DDR 400/333/266/200 DDR SDRAM DIMMs

• Acomoda dos DIMMS sin buffer

• Hasta 1 GB por DIMM con el tamaño de memoria máximo hasta 2 GB

CODEC de audio AC’97

Chipset

SiS964 (SB)

• Servicio concurrente de todos los Dispositivos DMA : Con

troladores IDE Dual, controlador SATA, tres controladores anﬁtriones USB 2.0/1.1, controlador LAN MAC y Controlador DMA Audio/Modem

• Conformidad de la especiﬁcación PCI 2.3 que soporta hasta 6 másters PCI

• Conformidad con la especiﬁcación Serial ATA 1.0, soporta el modo ahorro de energía

• Conformidad con AC’97 v2.3 que soporta 6 Canales de salidas de audio

• Controlador USB 2.0 integrado con tres hubs de raíz y ocho puertos funcionales

Graphics

• Motor de setup triangular VLIW de formato de punto ﬂotante de 32-bit incoporado

• Un motor de gráﬁcas BITBLT de 128-bit a línea de tubo 1T incorporado

• Acelerador Direct Draw & GDI+ Incorporado

• Soporta hasta tamaño de textura de 2048 x 2048

• Conformidad con la especiﬁcación AC’97 v2.3

• CODEC de 20-bit Duplex completo con índice de muestreo independiente y variable

• Soporte de alimentación dual: Digital: 5V/3.3V Analóg: 5V

Característica

Procesador

Esta placa principal usa un zócalo de 754-pin que lleva las sigtes. características:

• Acomoda CPUs AMD Sempron/Athlon 64

• Soporta hasta las velocidades de interfaz 1600MT/s HyperTransport

(HT)

La Tecnología HyperTransport

es un vínculo punto a punto entre dos dispositivos, habilita circuitos integrados para intercambiar la información en velocidades más rápidas que las tecnologías de interconexión disponibles actualmente.

Multi-Language Translation

Español

Esta placa principal soporta Ultra DMA bus mastering con índices de transferencia de 133/100/ 66MB/s.

La placa principal viene con las sigtes. opciones de expansión:

• Una renura PCI Express para la interfaz de Gráﬁcas

• Tres ranuras PCI de 32-bit

• Dos conectores IDE que soporta hasta cuatro dispositivos IDE

• Una interfaz de la unidad de disco ﬂoppy

• Dos conectores SATA de 7-pin

• Una ranura de Communications Network Riser (CNR1)

Opciones de Expansión

LAN Abordo (optativo)

• Soporta la operación de 10/100 Mbps

• Soporta Duplex medio y completo

• Soporta la operación IEEE 802.3u cláusura 28; 1.8V con tolerancia de señal de 3.3V IO.

El LAN abordo provee las sigtes. características:

I/O Integrado

La placa principal tiene un juego completo de puertos y conectores I/O:

• Dos puertos PS/2 para ratón y teclado

• Un puerto serial

• Un puerto paralelo

• Un puerto VGA

• Cuatro puertos USB

• Un puerto LAN (optativo)

• Clavijas de audio para micrófono, entrada y salida de línea

BIOS Firmware

La placa principal usa AMI BIOS que habilita usuarios para conﬁgurar muchas características de sistema que incluyen las sigtes:

• Administración de Alimentación

• Alarmas para despertar

• Parámetros de CPU

• Cronometraje de CPU y de memoria

También se lo puede usar el ﬁrmware para conﬁgurar los parámetros para diferentes velocidades de reloj de procesador.

Algunas especiﬁcaciones de hardware e ítems de software son sujetos a cambio sin aviso previo.

Multi-Language Translation

Português

O conjunto de chips SiS761GX Northbridge (NB) e SiS964 Southbridge (SB) é baseado numa arquitectura inovadora e escalável com ﬁabilidade e performance provadas.

SiS761GX(NB)

• O SiS MuTIOL vem incorporado para ligar SiS761GX e SiS964 MuTIOL Media IO juntamente

• Suporta Tecnologia de HyperTransport TM de largura de banda até 1600MT/s

• Express Bridge Host-para-PCI Integrada, compatível com 16X PCI Express sepc. 1.0a

• Suporta memória de visualização até 128MB com memória partilhada

• Acelerador de Gráﬁcos 3D de Elevada Qualidade & Elevada Performance

Memória

• Suporta DDR 400/333/266/200 DDR SDRAM DIMMs

• Acomoda dois DIMMs sem buffers

• Até 1 GB por DIMM com tamanho de memória máxima de até 2 GB

Conjunto de Chips

SiS964 (SB)

• Manutenção concorrente de todos os dispositivos DMA:

Controlador es IDE Dupl os, controlador SATA, três controladores host USB 2.0/1.1, Controlador LAN MAC e Controlador DMA Áudio/Modem

• Cumpre com especiﬁcação PCI 2.3 suportando até 6 PCI

masters

• Cumpre com especiﬁcação ATA 1.0 de Série, suporta

modo de poupança de energia

• Cumpre com AC’97 v2.3 suportando 6 Canais de saídas

áudio

• Controlador USB 2.0 Integrado com três hubs de raiz e

oito portas de função

Gráﬁcos

• Incorporado com dispositivo de conﬁguração triangular VLIW com formato de ponto ﬂutuante de 32 bit

• Incorporado com dispositivo de gráﬁcos BITBLT de 128 bit em paralelo 1T

• Direct Draw Incorporado & GDI+ Acelerador

• Suporta até 2048 x 2048 de formato de textura

Características

Processador

Esta motherboard usa uma ﬁcha de 754 pin que possui as seguintes características:

• Acomoda CPUs AMD Sempron/Athlon 64

• Suporta velocidades de interface de HyperTransport

(HT) até 1600MT/s

Tecnologia de HyperTransport

Té um link ponto-a-ponto entre dois dispositivos, permite circuitos integrados para trocar informação a velocidades muito mais elevadas que as disponíveis actualmente em tecnologias de interconexão.

Multi-Language Translation

Português

Esta motherboard suporta mastering bus Ultra DMA com taxas de transferência de 133/100/ 66MB/s.

A motherboard é fornecida com as seguintes opções de expansão:

• Uma ranhura PCI Express para Interface de Gráﬁcos

• Três ranhuras PCI de 32 bit

• Dois conectores IDE que suportam até quatro dispositivos IDE

• Um interface com drive de disco ﬂexível

• Dois conectores SATA de 7 pin

• Uma ranhura de Aumento da Rede de Comunicações (CNR1)

Opções de Expansão

Onboard LAN (opcional)

• Suporta funcionamento 10/100 Mbps

• Suporta Duplex pela metade e total

• Suporta IEEE 802.3u cláusula 28; funcionamento 1.8V com tolerância de sinal

3.3V IO.

O onboard LAN fornece as seguintes características:

I/O Integrado

A motherboard possui um conjunto completo de portas I/O e conectores:

• Duas portas PS/2 para rato e teclado

• Uma porta de série

• Uma porta paralela

• Uma porta VGA

• Quatro portas USB

• Uma porta LAN (opcional)

• Fichas áudio para microfone, entrada de linha e saída de linha

Microprogramação BIOS

Esta motherboard usa AMI BIOS que permitem aos utilizadores conﬁgurar muitas características do sistema incluindo as seguintes:

• Gestão de corrente

• Alarmes de despertar

• Parâmetros CPU

• Temporização de memória e CPU

A microprogramação poderá ser também usada para estabelecer parâmetros para diferentes velocidades de relógio do processador.

Algumas especiﬁcações de hardware e itens de software poderão ser sujeitos a alteraçõessem aviso prévio.

Codec Áudio AC’97

• Cumpre com especiﬁcação AC’97 v2.3

• CODEC de duplex total estéreo com 20 bits com taxa de amostragem variável e independente

• Suporte de alimentação dupla: Analógico 5V/3.3V: 5V

Multi-Language Translation

日本語

チップセット

SiS761GX Northbridge (NB)とSiS964 Southbridge (SB)チップセットは、実証された信頼性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいています。

SiS761GX(NB)

• SiS MuTIOL でMuTIOL Media IOチップセットであるSiS761GX

とSiS964 とを接続

• HyperTransportTM 技術をサポートで最大1600MT/秒の帯域幅を

提供

• Host-to-PCI Express Bridgeを統合し、16X PCI Express

sepc. 1.0a対応済み

• 最大 128MB までビデオメモリの共有を可能に

• 高性能で高品質の3D グラフィック・アクセラレータを搭載

SiS964 (SB)

• すべてのDMAデバイスの同時稼動が可能、これらのデバイスにはデ

ュアルIDE コントローラ、SATA コントローラ、3つのUSB 2.0/1.1 ホストコントローラ、LAN MAC コントローラ、およびオーディオ/モデム DMA コントローラがある

• PCI2.3規格に準拠することで、最大6つまでのPCIマスター設備の取り付けが可能

• シリアルATA 1.0仕様に準拠し、省電力モードをサポート

• AC’97 v2.3に準拠し、6 チャネルオーディオ出力をサポート

• 統合したUSB 2.0コントローラで、3つのルートハブと8つのポート

を提供

メモリ

• DDR 400/333/266/200 のDDR SDRAM DIMMに対応

• 2つの非バッファーDIMMを搭載

• 各DIMMスロットに1 GBまで装着可能で、合計2GBまでをサポート

AC’97 Audio CODEC

機能

プロセッサ

このマザーボードには、次の機能を持った754ピンソケットが一つあります：

• AMD Sempron/Athlon 64 プロセッサ取り付け可能

• 転送率が最大1600MT/秒までの HyperTransportTM (HT)インターフェース

を採用

HyperTransportTM技術とは、二つのデバイスを1対1( point-to-point)で接続する技術であり、従来のインターコネクト技術に比較して、集積回路同士の情報交換を高速化します。

• AC’97 v2.3仕様に準拠

• 20ビットステレオ全二重CODECで、独立で可変のサンプリング可能

• 1二重電源サポート： 5V/3.3V(デジタルの場合) 、5V(アナログの場合)

グラフィック

• 32ビット浮動小数点形式VLIWトライアングルセットアップエンジンを内蔵

• 1つの1T パイプライン化128ビットBITBLT グラフィックエンジンを内蔵

• Direct Draw & GDI+ アクセラレータを内蔵

• 最大2048 x 2048までの texture サイズに対応

Multi-Language Translation

日本語

拡張オプション

本マザーボードでは、次の拡張機能が利用できます。

• グラフィック・インターフェース用のPCI Express スロット x1

• 32ビットPCIスロット x3

• IDEヘッダー x2 (4つのIDEデバイスの接続を可能)

• フロッピーディスクドライブインターフェイス x1

• 7ピンSATAコネクタ X2

• CNR1（Communication Networking Riser）スロット x1

このマザーボードは、133/100/66MB/秒の転送速度でのUltra DMAバスマスタリングをサポートします。

オンボードLAN (オプション)

オンボードLANは、次の機能を提供します。

• 10/100 Mbps 動作をサポート

• 半/全二重をサポート

• IEEE 802.3u clause 28; 1.8V 動作をサポートし、入出力信号の許容電圧が

3.3V

統合の入出力ポート

マザーボードには、次のI/Oポートやコネクタを揃えています。

• マウスとキーボード用のPS/2ポート x2

• シリアルポート x1

• パラレルポート x1

• VGAポート x1

• USBポート x4

• LANポート x1(オプション)

• マイク、ラインイン、ラインアウト用オーディオジャック

BIOSファームウェア

本マザーボードはAMI BIOSを採用し、次の機能を含む多様なシステムの構成ををサポートします。

• 電源管理

• ウェークアップアラーム

• CPUパラメータ

• CPUとメモリとのタイミング

さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更することもできます。

一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更することがあります。

Multi-Language Translation

한국어

SiS761GX Northbridge (NB) 및 SiS964 Southbridge (SB) 칩셋은 혁신적이고 범위성 을 지닌 아키텍쳐를 기반으로 인정된 신뢰성과 성능을 지닌다.

SiS761GX(NB)

• SiS MuTIOL로 SiS761GX 와 SiS964 MuTIOL 미디어 IO

연결

• HyperTransport TMTechnology 에 최대 대역폭 1600MT/

s 지원

• 통합 Host-to-PCI Express Bridge, 16X PCI Express 1.0a

사양과 호환

• 공유 메모리와 함께 최대 128MB 디스플레이 메모리 지원

• 고 성능, 고 품질의 3D 그래픽 가속기

메모리

• DDR 400/333/266/200 DDR SDRAM DIMM 지원

• 2 개의 unbuffered DIMM 사용

• DIMM 당 최대 1 GB, 최대 메모리 2 GB

AC’97 오디오 코덱

칩셋

SiS964 (SB)

• 모든 DMA 장치의 동시 사용: 듀얼 IDE 컨트롤러, SATA 컨

트롤러, 3 개의 USB 2.0/1.1 호스트 컨트롤러, LAN MAC 컨 트롤러 및 오디오/모뎀 DMA 컨트롤러

• 최대 6 개의 PCI 마스터를 지원하는 PCI 2.3 사양과 부합

• 시리얼 ATA 1.0 사양과 부합, 절전 모드 지원

• 6 개의 오디오 출력 채널을 지원하는 AC’97 v2.3 과 부합

• 3 개의 루트 허브와 8 개의 기능 포트를 지닌 통합 USB 2.0

컨트롤러

그래픽

• 32 비트 플로팅 포인트 포맷 VLIW 트라이앵글 셋업 엔진 내장

• 1T pipelined 128 비트 BITBLT 그래픽 엔진 내장

• 빌트인 Direct Draw & GDI+ 가속기

• 최대 텍스처 크기 2048 x 2048 지원

• AC’97 v2.3 사양 부합

• 독집적이고 다양한 샘플링 속도를 지닌 20 비트 스테레오 풀-듀플렉스 코덱

• 이중 전원 지원: 디지털: 5V/3.3V 아날로그: 5V

특성

프로세서

본 마더보드는 다음과 같은 특성을 지닌 754 핀 소켓을 사용합니다:

• AMD Sempron/애슬론 64 CPU 사용

• HyperTransport

(HT) 인터페이스 속도 최대 1600MT/s 지원

HyperTransport

기술은 두 장치간의 point-to-point 링크로, 집적 회로가 기존의

상호 연결 기술 보다 더 빠른 속도로 정보를 교환할 수 있다.

Multi-Language Translation

한국어

본 마더보드는 전송 속도 133/100/66MB/s 로 Ultra DMA 버스 마스터링을 지원한다.

본 마더보드의 확장 옵션은 다음과 같다:

• 그래픽 인터페이스 용 PCI Express 슬롯 1 개

• 32 비트 PCI 슬롯 3 개

• 최대 4개의 IDE 장치를 지원하는 IDE 커넥터 2 개

• 플로피 디스크 드라이브 인터페이스 1 개

• 7 핀 SATA 커넥터 2 개

• Communications Network Riser (CNR1) 슬롯 1 개

확장 옵션

보드 내장 LAN (선택 사항)

• 10/100 Mbps 지원

• half 및 full Duplex 지원

• IEEE 802.3u 조항 28 지원; 3.3V IO 시그널 용인, 1.8V 작업.

보드 내장 LAN 은 다음과 같은 특성이 있다:

통합 I/O

본 마더보드는 풀 셋트의 I/O 포트 및 커넥터가 있다:

• 마우스 및 키보드용 PS/2 포트 2 개

• 시리얼 포트 1 개

• 패러럴 포트 1 개

• VGA 포트 1 개

• USB 포트 4 개

• LAN 포트 1 개 (선택 사항)

• 마이크, 라인 입력 및 라인 출력용 오디오 잭

BIOS 펌웨어

본 마더보드는 다음과 같은 시스템 특성을 구성할 수 있는 AMI BIOS 를 사용한다:

• 전원 관리

• Wake-up 알람

• CPU 파라미터

• CPU 및 메모리 타이밍

펌웨어로 다른 프로세서 클록 속도의 파라미터를 설정할 수도 있다.

몇 하드웨어 사양 및 소프트웨어 아이템은 사전 통보 없이 변경될 수 있습 니다.

Multi-Language Translation

繁體中文

SiS761GX北橋(NB)及SiS964南橋(SB)晶片組在研發設計上採用了創新且具擴充性之架構，具備優良的可靠性及性能。

SiS761GX(NB)

‧ 設置有SiS MuTIOL，用以連接SiS761GX 及SiS964 MuTIOL Media

IO晶片組；

‧ 支援 HyperTransportTM 技術，提供高達1600MT/s 的頻寬 ‧ 整合了 Host-to-PCI Express Bridge，相容於16X PCI Express sepc.

1.0a規格

‧ 支援共享高達128MB 的顯示記憶體 ‧ 具有高效能、高品質之3D 繪圖加速器

SiS964(SB)

‧ 支援DDR 400/333/266/200 DDR SDRAM DIMM ‧ 可安裝2個非緩衝式DIMM ‧ 各DIMM可安裝1GB記憶體，共可支援高達2GB的記憶體容量

功能

處理器

本主機板配備具有如下功能的754針插槽:

‧ 適用於AMD Sempron/Athlon 64 處理器 ‧ 支援高達1600MT/秒的HyperTransportTM (HT)介面傳輸速率

HyperTransportTM技術為以點對點方式連接兩台設備的技術，藉此，積體電路間能夠以

後高於現有各種內部連接技術(interconnect technology)技術的速度來交換資訊。

晶片組

AC'97 音頻編碼器

記憶體

‧ 所有DMA設備可同時提供服務，這些設備包括：Dual IDE 控制

器、SATA 控制器、3個USB 2.0/1.1 主控器、LAN MAC 控制器、

及音效/數據機 DMA 控制器

‧ 相容於 PCI 2.3規格，支援6個PCI主控器 ‧ 符合序列ATA 1.0規格，並支援省電模式 ‧ 符合AC'97 v2.3規格，支援6聲道音訊輸出 ‧ 內建USB 2.0/1.1控制器，提供8個連接埠

‧ 相容於AC'97 v2.3規格 ‧ 提供20位元立體音效全雙工CODEC，具有獨立及可變的採樣率 ‧ 雙電源支援：5V/3.3V(數位)、 5V(類比)

‧ 內建32位元浮點方式VLIW 幾何運算圖形加速引擎(triangle setup engine) ‧ 內建一1T 管線化128位元BITBLT繪圖引擎 ‧ 內建有 Direct Draw & GDI+ 加速器 ‧ 支援高達2048 x 2048 texture 尺寸

繪圖卡

Multi-Language Translation

繁體中文

擴充選項

本主機板包括下列擴充選項：

• 1 個繪圖卡用PCI Express 擴充槽

• 3 個 32-bit PCI 插槽

• 2 個 IDE 接頭，支援 4個 IDE 裝置

• 1 個軟碟機介面

• 2個7針SATA插頭

• 1個通訊網路附加卡(CNR1)插槽

本主機板支援傳輸率133/100/66 MB/秒下的Ultra DMA 匯流排主控功能。

內建區域網路 (選購)

內建區域網路提供下列功能：

• 支援10/100 Mbps 動作

• 支援半/全雙工

• 支援IEEE 802.3u clause 28; 1.8V 動作，提供3.3V的 IO信號容限

整合 I/O

主機板具有一組齊全的 I/O 連接埠及連接頭：

• 2 個 PS/2 埠，供滑鼠與鍵盤使用

• 1 個串列埠

• 1 個平行埠

• 1 個VGA埠

• 4 個USB埠

• 1 個區域網路埠(選購)

• 麥克風音頻插座、線級輸入及線級輸出

BIOS 韌體

本主機板使用AMI BIOS，使用者可以組態設定許多系統功能，包括如下：

• 電源管理

• 喚醒警鈴

• CPU參數

• CPU及記憶體的時脈定時

此外，也可藉由參數的設定，調整處理器的時脈速度。

部份硬體規格和軟體內容可能會在未經通知的情況下更動，敬請見諒。

Multi-Language Translation

简体中文

SiS761GX 北桥 (NB) 和 SiS964 南桥 (SB) 芯片组是基于一种新型的、可扩展的架构，能提供已经证明的可靠性和高性能。

SiS761GX(NB)

• SiS MuTIOL 将 SiS761GX 和 SiS964 MuTIOL Media IO 结

合

• 支持 HyperTransport

T M

技术，带宽可达 1600MT/s

• 集成主机到 PCI Express x1 桥路，符合 16X PCI Express

1.0a 标准

• 最大支持 128MB 显存，共享内存

• 高质量和高性能 3D 图形引擎

内存

• 支持 DDR 400/333/266/200 DDR SDRAM DIMM

• 支持 2 个非缓冲 DIMM

• 每个插槽支持 1 GB，总共最大可支持 2 GB

AC’97 音频编解码器

芯片组

SiS964 (SB)

• 所有 DMA 设备的并发服务：双 IDE 控制器、SATA 控制

器、3 个 USB 2.0/1.1主控器、LAN MAC 控制器和音频/调制解调器 DMA 控制器。

• 符合 PCI 2.3 规格，最多支持 6 个 PCI 主控器

• 符合串行 ATA 1.0 规格，支持节电模式

• 符合 AC’97 v2.3 规格，支持 6 声道音频输出

• 集成 USB 2.0 控制器，带有 3 个 Root Hub 和 8 个功能

端口

图形

• 内建 32 位浮点式 VLIW 三角设置引擎

• 内建一个 1T 管道 128 位 BITBLT 图形引擎

• 内建 Direct Draw & GDI+ 加速器

• 支持 2048 x 2048 纹理尺寸

• 兼容 AC’97 v2.3 规格

• 具有可调独立采样速率的 -20 位全双工 CODEC（编解码器）

• 支持双电源：数字：5V/3.3V 模拟：5V

功能

处理器

主板使用一个 754-pin 插座，此插座具有以下特点：

• 支持 AMD Sempron/Athlon 64 CPU

• 支持 1600MT/s HyperTransportTM (HT) 接口速度

HyperTransportTM 技术是一种在两台设备间进行点到点连接的技术，它可以让集成电路使用比当前互连技术更高的速度进行信息交换。

Multi-Language Translation

简体中文

主板支持 Ultra DMA 总线控制，传输速率可达 133/100/66MB/s。

此主板提供如下扩展选项：

• 1 个用于图形接口的 PCI Express 插槽

• 3 个 32 位 PCI 扩展插槽

• 2 个 IDE 接口，可支持 4 个 IDE 设备

• 1 个软驱接口

• 2 个 7-pin SATA 接口

• 1 个通信网络转接 (CNR1) 插槽

扩展选项

Onboard LAN（可选）

• 支持 10/100 Mbps 工作模式

• 支持半双工和全双工

• 支持 IEEE 802.3u 条款 28；1.8V 工作，带 3.3V IO 信号容错

板上集成的 LAN 提供以下功能：

集成 I/O

此主板具有完整的 I/O 端口和插孔：

• 2 个用于连接鼠标和键盘的 PS/2 端口

• 1 个串口

• 1 个并口

• 1 个 VGA 端口

• 4 个 USB 端口

• 1 个 LAN 端口（可选）

• 麦克风、线入和线出声音插孔

BIOS

此主板使用 AMI BIOS，可以让用户自己配置以下系统功能：

• 电源管理

• 唤醒报警

• CPU 参数

• CPU 和记忆定时

还可用于设置不同处理器时钟速度的参数。.

某些硬件规格和软件项目若有更改恕不另行通知。

Multi-Language Translation

Русский

Чипсеты SiS761GX «Северный мост» (Northbridge, NB) и SiS964 «Южный мост» (Southbridge, SB) построены с использованием инновационной масштабируемой архитектуры, обеспечивающей высокую надежность и производительность.

SiS761GX(NB)

• Для соединения мостов SiS761GX и SiS964 MuTIOL Media IO используется шина SiS MuTIOL

• Поддерживается технология HyperTransport TM, обеспечивающая пропускную способность до 1600MT/ s

• Интегрированный мостик Host-to-PCI Express, совместимость со спецификацией 16X PCI Express вер. 1.0a

• Поддержка видеопамяти до 128MB (разделенная память)

• Поддержка высокопроизводительного акселератора

высококачественной графики 3D

Память

• Поддержка памяти DDR 400/333/266/200 DDR SDRAM DIMM

• Обслуживает 2 модуля небуферизованной памяти DIMM

• Обслуживает до 1 ГБ на модуль DIMM (максимально до 2 ГБ памяти)

Чипсет

SiS964 (SB)

• Параллельное обслуживание всех DMA-устройств :

Двойной IDE-контроллер, SATA-контроллер, три USB

2.0/1.1 хост-контроллера, контроллер LAN MAC и аудио/модем DMA-контроллер

• Совместимость со спецификацией PCI 2.3,

поддерживающей до 6 PCI master-устройств

• Совместимость со спецификацией Serial ATA 1.0,

поддержка режима энергосбережения

• Совместимость с AC’97 v2.3, поддержка 6-канального

аудиовыхода

• Встроенный контроллер USB 2.0 с трехканальным

концентратором и восьмью функциональными портами

Графика

• Интегрированный 32-битовый модуль VLIW triangle setup для вычислений в режиме плавающей запятой

• Интегрированный графический модуль 1T pipelined 128-bit BITBLT

• Встроенный акселератор Direct Draw & GDI+

• Поддержка размеров текстуры до 2048 x 2048

Характеристики

Процессор

Технология HyperTransport

обеспечивает связь двух устройств по протоколу pointto-point, позволяя гораздо более быстрый обмен информацией между интегральными микросхемами, чем тот, который обеспечивается существующими технологиями.

Плата использует сокет 754-pin и обладает следующими характеристиками:

• Размещает процессоры AMD Sempron/Athlon 64

• Поддерживает технологию 1600MT/s HyperTransportTM (HT)

Multi-Language Translation

Русский

Плата поддерживает захват управления шиной Ultra DMA со скоростью передачи 133/100/66MБ/с.

Существуют следуюшие опции расширения данной материнской платы:

• Один слот PCI Express для графического интерфейса

• Три 32-битовых слота PCI

• Два разъема IDE с поддержкой до четырех устройств IDE

• Один разъем для накопителя на гибких дисках

• Два разъема 7-pin SATA

• Oдин слот CNR1

Возможности расширения

Встроенный сетевой адаптер LAN (опционально)

• Поддержка режимов10/100 Mbps

• Поддержка полного и половинного дуплекса

• Поддержка IEEE 802.3u п. 28; работа при напряжении 1.8V при допустимом сигнале на входе/выходе 3.3V

Встроенный сетевой адаптер LAN обладает следующими характеристиками:

Интегрированный вход/выход

Плата снабжена полным набором портов входа/выхода и разъемов:

• Два порта PS/2 для подключения мыши и клавиатуры

• Один серийный порт

• Один параллельный порт

• Один порт VGA

• Четыре порта USB

• Один порт LAN (опционально)

• Гнездо для подключения микрофона, гнезда аудио-входа и выхода

BIOS

Плата работает под AMI BIOS, который позволяет пользователю конфигурировать различные характеристики системы:

• Управление питанием

• Сигналы пробуждения системы

• Параметры CPU

• Время доступа для CPU и памяти

BIOS допускает также установку параметров для различных частот процессора.

Некоторые параметры платы и характеристики ее программного обеспечения могут быть изменены без предварительного уведомления.

AC’97 Аудио CODEC

• Совместим со спецификацией AC’97 v2.3

• 20-битовый стерео-КОДЕК полный дуплекс с независимым и переменным сэмплингом

• Поддержка двойного электропитания: цифровое: 5V/3.3V, аналоговое: 5V

Multi-Language Translation

Polski

Mostek północny (NB) SiS761GX i mostek południowy (SB) SiS964 chipsetu oparty jest na nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i funkcjonalnoœci.

SiS761GX(NB)

• SiS MuTIOL jest włączony w celu zapewnienia połączenia między urządzeniami SiS761GX i SiS964 MuTIOL Media IO

• Zabezpiecza technologię HiperTransportu

w paśmie do

1600MT/s

• Zintegrowany mostek Host-to-PCI Express, zgodny z protokołem 16X PCI Express w standardzie 1.0a

• Zabezpiecza do 128 MB pamięci wideo z pamięci wspólnej

• Obsługa zintegrowanego akseleratora graﬁki 3D

Pamięć

• Obsługuje pamięci typu DDR 400/333/266/200 DDR SDRAM DIMM

• Zaopatrzony w dwa gniazda niebuforowanej pamięci typu DIMM

• Obsługuje pamięć DIMM do pojemności 1 GB każda; maksymalna możliwa pojemność pamięci do 2 GB

Chipset

SiS964 (SB)

• Obsluguje wszystkie współczesne urządzenia DMA: kontrolery dual IDE, kontrolery SATA, trzy kontrolery USB

2.0/1.1, kontroler LAN MAC i kontroler audio/modem DMA

• Zgodnie z protokołem PCI 2.3 obsługuje do 6 urządzeń PCI typu masters

• Zgodnie z protokołem Serial ATA 1.0 zapewnia tryb oszczędności energii

• Zgodnie z protokołem AC’97 v2.3 zapewnia 6 kanałowe wyjście audio

• Zintegrowany kontroler USB 2.0 z trójdrożnym rozdzielnikiem i ośmiofunkcyjnym złączem

Graﬁka

• Wbudowany 32-bitowy procesor formatu zmiennoprzecinkowego VLIW triangle setup

• Wbudowany 128-bitowy procesor graﬁczny 1Tpipelined BITBLT

• Wbudowany przyśpieszacz Direct Draw & GDI+

• Obsługuje tekstury do rozmiarów 2048 x 2048

Cechy

Procesor

Ta płyta główna zaopatrzona jest w podstawkę dla procesorów z 754 nóżkami i charakteryzuje się następującymi cechami:

• Przystosowany do obsługi procesorów Sempron/Athlon 64 ﬁrmy AMD

• Obsługuje złącze HyperTransportTM (HT) z szybkością do 1600MT/s

Technologia HiperTransportu

jest protokołem komunikacji między dwoma urządzeniami, który umożliwia układom zcalonym wymieniać informację z dużo większymi szybkościami niż dotychczas stosowane technologie wzajemnych połączeń.

Multi-Language Translation

Polski

Płyta głwna obsługuje magistralę Ultra DMA o szybkościach przesyłu 133/100/66MB/s.

Płyta głwna wyposażona jest w następujące gniazda:

• Jedno gniazdo do karty graﬁcznej typu PCI Express

• Trzy 32-bitowe gniazda PCI

• Dwa złącza IDE mogące obsłużyć do czterech urządzeń IDE

• Jedno złącze obsługujące stacje dyskietek

• Dwa 7-nóżkowe złącza SATA

• Jedno gniazdo CNR1

Możliwości rozbudowy

Zintegrowana obsługa sieci LAN (opcjonalnie)

• Obsługuje operacje z szybkościami 10/100 Mbps

• Obsługuje half/full Duplex

• Obsługuje IEEE 802.3u z klauzulą 28, operuje na sygnałach 1,8 V przy 3,3 V We/Wy

Zintegrowana obsługa sieci LAN posiada następujące właściwości:

Zintegrowane We/Wy

Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:

• Dwa gniazda PS/2 dla myszy i klawiatury

• Jedno gniazdo szeregowe

• Jedno gniazdo równoległe

• Jedno gniazdo VGA

• Cztery gniazda USB

• Jedno gniazdo LAN (opcjonalnie)

• Gniazdo wejściowe mikrofonowe, gniazdo wejściowe i wyjściowe dzwięku (audio)

Firmowy BIOS

Płyta głwna wyposażona jest w BIOS ﬁrmy AMI, który pozwala użytkownikowi konﬁgurować wiele cech systemu włączając w to następujące właściwości:

• Zarządzanie poborem mocy

• Alarmy typu Wake-up

• Parametry pracy procesora

• Ustalenia szybkoœci pracy procesora i pamiêci

BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara procesora.

Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie bez uprzedniego powiadomienia.

AC’97 audio CODEC

• Zgodny z AC’97 w wersji 2.3

• 20 bitowy stereo CODEC full-duplex z niezależną i zmienną częstotliwością próbkowania

• Akceptuje dwa rodzaje zasilania w trybie cyfrowym: 5 V/3.3 V zaś w trybie analogowym: 5 V

Multi-Language Translation

Česky

Čipy northbridge (NB) SiS761GX a southbridge (SB) SiS964 jsou založeny na inovativní a škálovatelné architektuře s ověřenou spolehlivostí a výkonností.

SiS761GX(NB)

• SiS MuTIOL je určen ke vzájemnému propojení SiS761GX a SiS964 MuTIOL Media IO

• Podpora technologie HyperTransport

s maximální

šířkou pásma 1600MT/s

• Integrované přemostění mezi hostitelem a sběrnicí PCI Express, splňující požadavky 16x PCI Express SPEC 1.0a

• Podpora až 128MB paměti graﬁckého systému (sdílená paměť)

• Podpora vysoce výkonného 3D graﬁckého akcelerátoru s vysokou kvalitou

Paměť

• Podpora pamětí typu DDR 400/333/266/200 DDR SDRAM DIMMs

• Instalovat je možné až dva DIMM moduly bez vyrovnávací paměti

• Až 1 GB paměti na jeden modul DIMM s maximální velikostí paměti do 2 GB

Zvukový kodek AC’97

Čipová sada

SiS964 (SB) • Současná obsluha všech zařízení DMA: duální řadiče IDE,

řadič SATA, tři hostitelské řadiče USB 2.0/1.1, řadič LAN MAC a řadič audio/modemu DMA

• Splňuje požadavky standardu PCI 2.3 s podporou 6 hlavních kanálů PCI

• Splňuje požadavky standardu Serial ATA 1.0, podporuje režim řízení spotřeby energie

• Splňuje požadavky standardu AC’97 v2.3, podporuje 6 výstupních audio kanálů

• Integrovaný řadič USB 2.0 se třemi kořenovými rozbočovači a osmi funkčními porty.

Graﬁka

• Vestavěné 32bitové jádro pracující s formátem VLIW s plovoucí desetinnou čárkou

• Vestavěné graﬁcké jádro 1T se 128bitovou pipeline BITBLT

• Vestavěná podpora akcelerátoru Direct Draw a GDI+

• Podpora velikosti textur až 2048 x 2048

• Splňuje požadavky standardu AC’97 v2.3

• 20bitový plně duplexní stereo kodek s nezávislou a proměnnou vzorkovací frekvencí

• Podpora duálního napájení: Digitální: 5 V / 3,3 V Analogové: 5 V

Vlastnosti

Procesor

Tato základní deska využívá 754kolíkovou patici nabízející následující vlastnosti:

• Podpora procesoru AMD Sempron/Athlon 64

• Podpora rychlostí rozhraní HyperTransportTM (HT) až 1600 MT/s

Technologie HyperTransport

je přímým spojením mezi dvěma zařízeními, umožňující integrovaným obvodům výměnu informací vyššími rychlostmi, než jaké nabízejí současné technologie.

Multi-Language Translation

Česky

Tato základní deska podporuje řízení sběrnice Ultra DMA s přenosovými rychlostmi 133/ 100/66 MB/s.

Základní deska je dodávána s následujícími možnostmi rozšíření

• Jedna patice PCI Express pro graﬁckou kartu

• Tři 32bitové patice PCI

• Dva konektor IDE podporující až čtyři zařízení IDE

• Jedno rozraní pro disketovou mechaniku

• Dva 7kolíkové konektor SATA

• Jedna patice CNR1

Možnosti rozšíření

Vestavění síťové rozhraní LAN (volitelně)

• Podpora provozu 10/100 Mbps

• Podpora plného/polovičního duplexního provozu

• Podpora IEEE 802.3u par. 28; provoz 1,8 V s tolerancí I/O signálu 3,3 V.

Vestavěné síťové rozhraní LAN nabízí následující možnosti:

Integrovaný vstup/výstup

Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:

• Dva porty PS/2 pro myš a klávesnici

• Jeden sériový port

• Jeden paralelní port

• Jeden port VGA

• Čtyři porty USB

• Jeden port LAN (volitelně)

• Zvukové konektory pro mikrofon, zvukový vstup a výstup

Firmware BIOS

Základní deska využívá BIOS formy AMI, který uživateli umožňuje nakonﬁgurovat mnoho systémových parametrů, včetně následujících:

• Řízení spotřeby

• Alarmy při spouštění systému

• Parametry CPU

• Časování CPU a paměti

Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence procesoru.

Některé technické parametry hardware a software se mohou měnit bez předchozího upozornění.

Multi-Language Translation

Română

Seturile de chipuri SiS761GX Northbridge (NB) şi SiS964 Southbridge (SB) se bazează pe o arhitectură inovatoare şi scalabilă, care s-a impus deja prin ﬁabilitate şi performanţă.

SiS761GX(NB)

• SiS MuTIOL este incorporat pentru a conecta SiS761GX şi SiS964 MuTIOL Media IO

• Suportă tehnologia HyperTransportTM cu lăţime de bandă de cel mult 1600 MT/s

• Host-to-PCI Express Bridge integrat, compatibil cu speciﬁcaţia 16X PCI Express 1.0a

• Suportă o memorie video de cel mult 128 MB cu memorie partajată

• Suport pentru accelerator graﬁc de înaltă performanţă şi 3D de cea mai bună calitate

Memoria

• Funcţionează cu module SDRAM DIMM DDR 400/333/266/200 DDR

• Poate funcţiona cu două module DIMM fără zonă tampon

• Poate funcţiona cu module DIMM de cel mult 1 GB, iar cantitatea maximă de memorie este de 2 GB

AC’97 Audio CODEC

Setul de chipuri

SiS964 (SB)

• Deservire concurentă a tuturor aparatelor DMA: controlere IDE duale, controler SATA, trei controlere gazdă USD 2.0/

1.1, controler LAN MAC şi controler DMA Audio/Modem

• Compatibil cu speciﬁcaţia PCI, versiunea 2.3, care suportă cel mult 6 module PCI master

• Compatibil cu speciﬁcaţia Serial ATA 1.0, suportând modul de funcţionare economicos

• Compatibil cu AC’97, versiunea 2.3, suportând 6 canale audio de ieşire

• Controler USB 2.0 integrat, cu trei socluri de bază şi opt porturi funcţionale

Graﬁcă

• Format VLIW de calcul în triunghi în virgulă mobilă, de 32 biţi, incorporat

• Motor graﬁc BITBLT de 128 biţi, cu canal de prelucrare 1T, incorporat

• Direct Draw & GDI+ Accelerator încorporat

• asigură mărime textură de până la 2048 x 2048

• Compatibil cu speciﬁcaţia AC’97, versiunea 2.3

• CODEC 20-bit stereo full-duplex cu frecvenţă de comutare independentă şi variabilă

• suport curent dual: Digital: 5V/3.3V Analog: 5V

Caracteristici

Procesorul

Această placă de bază utilizează un soclu 754, având următoarele caracteristici:

• Funcţionează cu unităţi centrale AMD Sempron/Athlon 64

• Suportă interfeţe HyperTransportTM (HT) cu viteze de până la 1600 MT/s

Tehnologia HyperTransport

este o legătură punct-la-punct între două aparate, care permite viteze mult mai mari de schimb al informaţiilor între circuitele integrate, decât cel asigurat de tehnologiile de interconectare actuale.

Multi-Language Translation

Română

Această placă de bază suportă Ultra DMA bus mastering cu viteza de transfer de 133/100/ 66MB/s.

Placa de bază este dotată următoarele posibilităţi de extindere:

• Un slot PCI Express pentru interfaţă graﬁcă

• Trei sloturi PCI de 32 biţi

• Două conectoare IDE care suport cel mult 4 instrumente IDE

• O interfaţă pentru unitate ﬂoppy

• Două conectoare SATA 7

• Un slot CNR1

Opţiuni de extindere

Onboard LAN (opţional)

• Asigură operare 10/100 Mbps

• Asigură half şi full Duplex

• Asigură IEEE 802.3u clauza 28; operare 1.8V cu toleranţă semnal 3.3V IO

Onboard LAN are următoarele caracteristici:

I/O integrată

Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:

• Două porturi PS/2, pentru mouse şi tastatură

• Un port serial

• Un port paralel

• Un port VGA

• Patru porturi USB

• Un port LAN (opţional)

• Mufe audio pentru microfon, intrare şi ieşire audio

Firmware BIOS

Placa de bază utilizează AMI BIOS, care permite utilizatorului să conﬁgureze mai mulţi parametri ai sistemului, cum ar ﬁ:

• Gestionarea energiei

• Alarme de trezire

• Parametri CPU

• Temporizare CPU şi memorie

Acest ﬁrmware poate ﬁ utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale procesorului.

Anumite speciﬁcaţii hardware şi elemente de software pot ﬁ modiﬁcate fără înştiinţare prealabilă.

Multi-Language Translation

Български

Чипсетът със северен мост SiS761GX (NB) и южен мост SiS964 (SB) е изграден на базата на оригинална архитектура с възможност за надстройка с доказана надеждност и производителност.

SiS761GX(NB)

• Интегрирана система SiS MuTIOL за връзка между мостовете SiS761GX и SiS964 MuTIOL Media IO

• поддръжка на технологията HyperTransport

със скорост

до 1600MT/s

• Интегриран мост Host-to-PCI Express, съвместим със спецификациите 16X PCI Express 1.0a

• поддръжка на видео памет до 128MB със споделена памет

• поддръжка на високопроизводителен 3D графичен ускорител

Памет

• поддръжка на DDR400/333/266/200 DDR SDRAM DIMMs

• поддръжка на до два небуферирани DIMM слота

• до 1 GB памет на 1 DIMM канал с максимален капацитет 2 GB

AC’97 Audio CODEC

Чипсет

SiS964 (SB)

• Едновременна поддръжка на всички DMA устройства: два IDE контролера, SATA контролер, три USB 2.0/1.1 host контролера, LAN MAC контролер и Audio/Modem DMA контролер.

• съвместимост със спецификацията PCI 2.3 с поддръжка до 6 PCI мастъра

• съвместимост със спецификацията Serial ATA 1.0 с поддръжка на икономичен режим на захранване

• съвместимост с AC’97 v2.3 с поддръжка на 6-канален звук

• Интегриран USB 2.0 контролер с три колектора и осем функционални порта

Графичен чип

• интегриран triangle setup engine с 32-bit формат на плаваща запетая VLIW

• интегрирано графично ядро 1T pipelined 128-bit BITBLT

• Интегриран Direct Draw & GDI+ Ускорител

• Поддръжка на размер на текстурите до 2048 x 2048

• съвместимост със спецификацията AC’97 v2.3

• 20-битов стерео Аудио КОДЕК full-duplex с независима и вариативна честота (independent and variable sampling rate)

• Поддръжка на захранване: Цифрово: 5V/3.3V Аналогово: 5V

Спецификация

Процесор

Тази дънна платка използва 754-щифтов цокъл (754-pin socket) със следните параметри:

• Поддръжка на процесори AMD Sempron/Athlon 64

• Поддръжка на технологията HyperTransport

(HT) със скорост до

1600MT/s

Технологията HyperTransport

е връзка точка-до-точка (point-to-point) между две устройства, която предоставя възможност интегрираните вериги да обменят информация на много по-висока скорост от досегашно съществуващите технологии.

Multi-Language Translation

Български

Дънната платка поддържа шина Ultra DMA 133/100/66MB/s.

Дънната платка има следните разширителни възможности:

• Един PCI Express слот за графичен интерфейс

• три 32-bit PCI слота

• два IDE конектора с поддръжка до четири IDE устройства

• един конектор за флопидисково устройство

• два 7-щифтови SATA конектораs

• един слот CNR1

Възможности за разширяване

Интегриран мрежов контролер (опция)

• Поддръжка на режими на работа 10/100 Mbps

• Поддръжка на режими на работа Half /Full Duplex

• Поддръжка на стандарта IEEE 802.3u точка 28; захранване от 1.8V с толеранс на сигнала до 3.3V

Спецификация на интегрирания мрежов контролер:

Интегриран Вход/Изход контролер

Дънната платка има пълен набор от I/O портове и конектори:

• два PS/2 порта за мишка и клавиатура

• един сериен порт

• един паралелен порт

• един VGA порт

• четири USB порта

• един LAN порт (опция)

• Аудио жакове за микрофон, линеен вход и линеен изход

BIOS Firmware

Дънната платка използва AMI BIOS с възможност за различни системни настройки, включително

• управление на захранването

• Wake-up аларми

• параметри на процесора

• синхронизиране на процесора и паметта

настройка на скоростта на часовника на процесора

Хардуерните и софтуерни спецификации и параметри могат да бъдат изменени без предупреждение.

Multi-Language Translation

Magyar

A SiS761GX Northbridge (NB) és SiS964 Southbridge (SB) lapkakészletek egy új és méretezhető, nagy megbízhatóságú és teljesítőképességű architektúrára épülnek.

SiS761GX(NB) • Beépített SiS MuTIOL a SiS761GX és SiS964 MuTIOL

Media IO összekapcsolására

• Támogatja a max. 1600MT/s sávszélességű HyperTransportTM technológiát

• integrált Host-to-PCI Express Bridge híd, megfelel a 16X PCI Express 1.0a speciﬁkációnak

• Maximum 128MB képernyő-memóriát támogat, megosztott memóriával

• Nagyteljesítményű és csúcsminőségű 3D graﬁkus gyorsító támogatása

Memória

• 400/333/266/200 MHz-es DDR DDR SDRAM DIMM egységekkel működik

• Két puffermentes DIMM egységgel működik

• Maximum 1 GB-os DIMM egységeket támogat, maximális memória 2 GB

Lapkakészlet

SiS964 (SB)

• Az összes DMA eszköz egyidejű kiszolgálása: duál IDE vezérlők, a SATA vezérlő, három 2.0/1.1 USB gazda vezérlő, LAN MAC vezérlő, valamint Audio/Modem DMA vezérlő

• a PCI 2.3 szabvánnyal kompatibilis, maximum 6 PCI mastert támogat

• Kompatibilis a soros ATA 1.0 szabvánnyal, az energiatakarékos üzemmódot is támogatja

• Kompatibilis az AC”97 2.3-as verziójával, maximum 6 audio kimenet csatornát támogat

• Beépített USB 2.0 vezérlõ, amely három alaphub-bal és nyolc funkcionális porttal rendelkezik

Graﬁka

• Beépített 32 bites VLIW lebegőpontos háromszög számítás

• Beépített 1T csővonalas 128 bites BITBLT graﬁkus motor

• Beépített Direct Draw & GDI+ gyorsító

• Megfelel egészen 2048 x 2048 textúra méretnek

Jellemző

Processzor

Ez az alaplap 754 tűs foglalattal rendelkezik, ennek jellemzői pedig a következők:

• AMD Sempron/Athlon 64 központi egységekkel működik

• Maximum 1600 MT/s HyperTransportTM (HT) sebességű interfészt támogat

A HyperTransport

technológia egy ponttól pontig való kapcsolat két készülék között, és segítségével az integrált áramkörök közötti információcsere sebessége sokkal nagyobb, mint a jelenleg rendelkezésre álló összekapcsolási technológiák esetében.

Multi-Language Translation

Magyar

Ez az alaplap a 133/100/66MB/s átviteli sebességű Ultra DMA ’bus mastering’ megoldást is támogatja.

Az alaplap a következő bővítési lehetőségekkel rendelkezik:

• Egy PCI Express nyílás graﬁkai interfészhez

• Három 32 bites PCI foglalat

• Két IDE csatlakozó, amely összesen négy IDE eszközt támogat

• Egy hajlékonylemez meghajtó interfész

• Két 7 tűs SATA csatlakozó

• Egy CNR1 foglalat

Bővítési lehetőségek

Alaplapon levő LAN (választható)

• 10/100 Mbps működést biztosít

• Half és full duplex ellátás

• Megfelel az IEEE 802.3u 28-as kitételnek; 1.8V működés 3.3V IO jelzés toleranciával.

Az alaplapon levő LAN jellemzői:

Beépített I/O

Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:

• Két PS/2 port az egér és a billentyűzet számára

• Egy soros port

• Egy párhuzamos port

• Egy VGA port

• Négy USB port

• Egy LAN port (választható)

• Audio csatlakozók mikrofon, bemenet és kimenet számára

BIOS Firmware

Az alaplapon levő AMI BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja be, például:

• Energiagazdálkodás

• Ébresztési riasztások

• CPU paraméterek

• CPU és memória időzítés

A ﬁrmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.

Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül módosulhatnak.

AC’97 Audio CODEC

• Kompatibilis az AC”97 2.3-as változatának szabványával

• 20-bit stereo full-duplex CODEC önálló és változó mintavételezési

frekvenciát biztosít

• kettős áramellátás: Digitális: 5V/3.3V Analóg: 5V

ECS 761GX-M754 V3.0 (Acer OEM) User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual